In this Preview Unboxing Video I Take a look at 4 new Airsoft products from Arcturus all of them being AEG Airsoft Rifles with two based on the AK platform and the other two based on the AR platform. Three of the AEG Airsoft Rifles are mostly metal while I also feature a lower cost version with a Nylon Fiber Polymer receiver. All of these Replica AEG Airsoft Rifles are very good quality but you will get all metal (mostly steel and aluminum) build and a Hi-Cap and Mid-Cap magazine with the higher cost versions.
This review shows that low cost Airguns can perform just like higher priced Airguns. They may not be as realistic and all made out of metals for that added weight and feel but in terms of power and accuracy they can still get the job done as is with the Umarex NXG CO2 BB Pump Shotgun! In this Field Test Shooting Review I do just that, I test the power and accuracy first by shooting 5 rounds through my Chronograph to find out what the real world fps is, I then I shot 10 rounds down range at a fresh paper target to see what kind of grouping I can get and if the Umarex NXG CO2 BB Pump Shotgun is sighted in on the target out of the box.
Starting with the velocity test I first placed a brand new 12 gram CO2 into the Umarex NXG CO2 BB Pump Shotgun and loaded up the 10 rounds rotary magazine with Daisy Zinc Coated 4.5 mm Steel BB’s. The temperature was around 22 degrees Celsius which is 72 degrees Fahrenheit in the sea can indoor shooting range so not too warm or cold. The claimed fps from Umarex is 450, I was able to get an average of 403fps with the fastest shot hitting 425fps and the slowest shooting down to 388fps. So a bit under the Umarex claimed velocity but in the ball park.
Next I performed the accuracy test for the Umarex NXG CO2 BB Pump Shotgun and since the sights are non adjustable you kind of hope that where you aim is where the shots go but if they don’t then you will need to adjust your aim point just a bit. Out of the box the Umarex NXG CO2 BB Pump Shotgun did shoot a bit low but was fairly bang on side to side so when shooting at around 30 feet out you will need to aim just a tad over the intended target. Out of 10 shots, 8 rounds where all within a nice 1.5 inch grouping with a couple of flyers that I kind of want to keep out of this test because it was probably more me than the gun causing them to go off a bit. 1.5 inches is very good for a 4.5mm Steel BB Airgun!
All in all the Umarex NXG CO2 BB Pump Shotgun shot right around 400fps which is for sure a step up for something like a Red Ryder BB Rifle that at best can shoot 300fps. You also don’t have to work the pump as hard as you would the lever on a Red Ryder since the Umarex NXG CO2 BB Pump Shotgun is CO2 powered rather than spring powered. I also feel like the Umarex NXG Pump Shot was more accurate than the Red Ryder at least for me but that said some people can hit a nickel all day long with their Red Ryders! There are not a lot of Pump Action Looking Airguns out there in 4.5mm Steel BB versions and in more compact easier for younger or smaller shooters so if you fall into that category and want something in a shotgun format then the Umarex NXG CO2 BB Pump Shotgun may be perfect for you.
Trigger Pull: The trigger pull on the Umarex NXG CO2 BB Pump Shotgun is pretty decent, there is a short task up and fairly easy release as the pump action not only turns the rotary magazine but also cocks the internal hammer/striker system. So you will need to pump it before your first shot and after each shot.
Accuracy: I have not Field Test Reviewed the Umarex NXG CO2 BB Pump Shotgun yet but will be making a full Fields Test Review this week to find out what to expect in terms of accuracy and velocity. So we will find out if the fps is closer to the on the box specs of 450 fps or the mostly online specs of 490 fps. Perhaps somewhere in-between?
Build Quality: The Umarex NXG CO2 BB Pump Shotgun is almost all plastic which is not a bad thing in terms of quality and durability. The fact that it only weighs in at 2 pounds may make it feel kind of light and cheap but in a drop or fall situation it means it will most lily not sustain any damage because of the light weight. Most of todays airguns when made out of metals generally are made out of pot metal or zinc alloy which is a nice heavy metal that looks and feels great but is not super strong so when you drop a heavier gun made out of this material it can easily get damaged.
Realism: The Umarex NXG CO2 BB Pump Shotgun looks like a traditional pump action shotgun and even has a little bit of a recessed barrel to make it more believable but it is smaller in size since it is designed more for younger and smaller shooters. The light weight is not only a giveaway but makes ti feel more like a toy than a real gun. If you can ignore that then hopefully you can enjoy the Umarex NXG CO2 BB Pump Shotgun for what it is which is a low cost compact BB rifle made for customs interested in Airguns liek the Red Ryder but that perhaps want a bit more power.
Pros:
Low cost CO2 rifle great for all ages and sizes.
Has a fiber optic front sight.
Comes in a nice looking two tone Black/FDE color scheme.
Fairly easy to pump since the pumping action is not required to activate a spring or compress air.
Built in manual thumb safety.
Stock and high check rest position feel good and a good size length for smaller younger shooters.
Rotary drop out magazine holds 10 4.5mm steel BB’s for quick follow up shots.
Trigger feels pretty good, short and fairly light.
Full ambidextrous design.
Perhaps a step up for entry level shooter over a Red Ryder type BB rifle in terms of power.
Overall a decent looking air rifle.
Cons:
Mostly plastic, so a bit on the light weight side.
Sights are not adjustable in any way.
May be a bit cramped for larger shooters.
Comments: The Umarex NXG CO2 BB Pump Shotgun is not going to win any prizes for quality and realism but keep in mind it is really designed more for entry level younger shooters getting into the Airgun hobby. For them this will be not so intimidating as a larger, heavier more realistic version of a replica Shotgun. I think it will be realistic enough for most new Airgun Shooters and in terms of performance and features it is for sure a step up form something like a Red Ryder BB Rifle. I am looking forward to my upcoming Field Test Shooting Review out what the actual velocity is and what kind of groupings I can get shooting 30 feet down range on a paper target.
My Table Top Video of the Umarex NXG CO2 BB Pump Shotgun:
Umarex has released yet another Legends Replica Airgun and perhaps this one may be the most iconic yet, the M3 Grease gun with a history as far back as 1942. It was put into service int 1944 and then the later variant the M3A1 was used in the Korean War. Also make sure to watch my Table top Video for it for specifications and details along with more close up video.
Getting back to the Field Test Review for the Umarex Legends CO2 Blowback Full Auto M3 Grease Gun, as always I like to test each gun out in the Replace Airguns Indoor Sea Can Airguns Range first placing 5 rounds through my Chronograph to find out the real world velocity of each test gun, then I shoot 10 rounds in semi auto at a distance of 30 feet onto a paper target to see how tight of a grouping I can get shooting from a seated and rested position. With full auto Airguns I like to then perform a full auto shooting test to see how it groups in full auto as often times the full auto grouping will open up somewhat as some Blowback Full Auto Airguns do tend to move around a lot more in full auto mode.
For my Power or Velocity test I was using dual brand new CO2 cartages. Umarex does state that the Umarex Legends CO2 Blowback Full Auto M3 Grease Gun will shoot around 450 fps and with my 5 shot test I was able to confirm this and get close to this mark averaging 436fps. The temperature in the Sea Can was around 20 degrees Celsius or around 70 degrees Fahrenheit. Perhaps in warmer conditions I might hit the claimed 450 fps but I was close either way.
For my accuracy test I setup a new paper target 30 feet downrange and proceeded to place 10 shots into it using the peep sight on the Umarex Legends CO2 Blowback Full Auto M3 Grease Gun. I was fairly pleased with a fairly tight 1.5 inch grouping in semi auto. I then switched over to full auto fun mode and with the remaining BB’s I unloaded 50 or so rounds in very short order and as expected the grouping opened up to closer to a 4 inch grouping. This was kind of expected since the Umarex Legends CO2 Blowback Full Auto M3 Grease Gun uses an open bolt system which has a fairly heavy bolt which makes the blowback action more intense, similar to the KWC Mini Uzi but to a lessor degree.
Any time a company puts out another Full Auto Replica Rifle, especially full auto firing, I am 100% in on it. Both Crosman and Umarex have done a great job doing this and the Umarex Legends CO2 Blowback Full Auto M3 Grease Gun is another example of a well thought out and what I expect to be very popular Full Auto BB Rifle. Their Legends series encompasses guns of the later era which I personally really like since they are harder to come by in their real steel versions, so having them available in an easier to acquire version that you can even shoot in your back yard is a win win for everyone. I am also happy to confirm the high capacity double stack 60 round magazine seemed to feed pretty good for me only miss-feeding once during my testing while doing the Chronograph portion but it got back on track right away. If you’re into Full Auto Legendary Airguns then for sure pick one up from us!
In this Field Test Shooting Video I give the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol my usual Indoor Sea Can shooting field test using my Chronograph to see what the average 5 shot velocity is with .20 gram plastic Airsoft BB’s. I then shoot 10 rounds in semi auto at a paper target setup 30 feet down range using a seated shooting position with my hands rested on a sand bag up front for stability to find out what the accuracy is in semi auto mode. I follow this up with a full mag demo in full auto to see how large of a spread we get with this gun jumping around. If you want information on specifications and details along with some close up video of the Cybergun Licensed L6 .50AE Desert Eagle GBB Airsoft Pistolthen watch my Table Top Video for it here.
Starting off with my Chronograph test, the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol was able to get a 5 shot average of 392 fps with the fasters round hitting 400 fps and the slowest Airsoft BB recording 387 fps. Again I was using .20 gram Airsoft BB’s and the indoor temperature was around 20 degrees Celsius which is close to 70 degree Fahrenheit for reference so so the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol performed even better than the claimed on the box 380 fps.
Moving on to the accuracy portion of my Field Test Test for the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol, I carefully placed 10 rounds into my fresh paper target and was a bit dissapoitned in the rather spread out group I got. I feel like this is because of the high fps and lighter choice of Airosft BB I used for this test. When shooting a gun with higher fps it is best to use heavier Airsoft BB’s at least when it comes to accuracy as they won’t get that beach ball effect of floating around so much. I did also shoot the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol in Full auto which does rock around a lot because of the heavy blowback recoil and as expected BB’s kind of went all over but if I was shooting at a human sized target from that range I am sure most rounds would have found their intended target.
Overall the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol is a really nice Airsoft pistol. I love the way it looks and feels to hold in the hand and the blowback operation is very noticeable. It also shoots really hard for an Airsoft Pistol and other than the semi auto accuracy which may be corrected using heavier BB’s, it really does have a lot going for it. I may have to test it out again using heavier Airsoft BB’s to see if this improves accuracy for me at 30 feet out.
Trigger Pull: The trigger pull on the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol is single action only which means you will need to rack the slide to not only draw the hammer back but to also chamber the first round. After that the blowback action will do this for you until you are out of ammo and then the slide will lock back. You can also manually draw the hammer back if a round is already chambered. The trigger itself is really nice, it’s light, super short with a crisp light release perfect for fast action shooting.
Accuracy: At this point I have not made my Field Test Shooting portion of my review for the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol so I really don’t know what to expect? KWC claims an fps of 360 using CO2 as its power source and it is a realistic velocity based on previous Velocity tests with similar KWC Airsoft Guns. In terms of accuracy, again I have no idea since I have not reviewed this version of Desert Eagle before. So stay posted till next week when I make the Field Test Shooting Review for it.
Build Quality: Overall the metal and plastic build quality of the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol is good. It is mostly metal with a plastic frame, the real steel version would have an aluminum frame and has a weight closer to 4 pounds total so a bit lighter in terms of weight compared to the powder burning version. The fit and finishes look good.
Realism: The KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol is an excellent Replica Airsoft version of the real steel L6 Desert Eagle including the top and bottom rails and the ported front barrel. It also has full blowback action and you can fully field strip it. I like the addition of the fingered grips which I think adds ot the overall looks and function of this Airsoft Pistol.
Pros:
Lots of metal and good overall weight to it.
Very accurate replica of Desert Eagle L6.
Ergonomic rubberized grips.
Semi and full auto selectable.
Adjustable hop-up.
No orange tip.
CO2 for more power over GBB.
Uses standard KWC CO2 Desert Eagle magazines.
Picatinny rail top and bottom for lots of accessory mounting options.
Great light weight single action only trigger with super short take-up.
Cons:
Frame is plastic so compared to real steel version is much lighter.
Non adjustable sights, also all black so may be hard to see on darker targets.
No trademarks since non-licensed version via KWC direct.
Very large gun with large grips so not suitable for smaller handed shooters.
Comments: Going off just the looks and feel for the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol I can say for sure I do like it compared ot the standard KWC Desert Eagle with its venting up front and its ergonomic rubberized grips. I hope when I perform the Field Test Shooting Video fo fit it it performs well as the price point is good at around $200 Canadian and who doesn't want to have a Desert Eagle in their Replica Airgun collection at the end of the day!
My Table Top Video of the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol:
If you are wondering why I am doing another Field Test of a Crosman AR-15 type CO2 Full Auto BB Rifle… Well why not, any excuse to play around with one of these and I will take it. You never know, even though the Crosman R1 Fallen Patriots Blowback CO2 Full Auto BB Rifle is essentially just a re-skinned R1, what if it performs better or worse than the standard R1. I better test it out and find out for myself.
Like all my other Field Test Shooting Videos I test out the Velocity and Accuracy in the Replica Airguns Indoors Sea Can Shooting Range where I can control the temperature, wind and lighting conditions. The goal is to see if the velocity is what the manufacturer claims and what kind of groupings I can get in this case shooting 10 rounds in semi auto and the rest in full auto.
Starting with my velocity test for the Crosman R1 Fallen Patriots Blowback CO2 Full Auto BB Rifle I shot five 4.5mm Steel BB’s through my Chronograph and was able to average 389 fps. Crosman claims a max fps of 430 which would be best case scenario in what would most likely be fairly warm shooting conditions. During my testing the temperature was not overly warm or cool, right around room temperature so around 20 degrees Celsius (70 ish degrees Fahrenheit) and I was using dual brand new CO2 Cartridges.
Next I tested out the accuracy for the Crosman R1 Fallen Patriots Blowback CO2 Full Auto BB Rifle first shooting 10 rounds in semi auto and then dumping the rest of the magazine in full auto. Right out of the box using the iron pop-up sights I was able to get all but 1 shot in the Bulls-eye which is about 1 inch in diameter so not only is the Crosman R1 Fallen Patriots Blowback CO2 Full Auto BB Rifle very accurate but it was really well centered out of the box in my case. Switching over to full auto the grouping spread out as expected more to around 2+ inches and placing a bit lower on the target but this is expected when shooting a blowback Airgun in full auto as it will move around a bit.
I do have to say the Crosman R1 Fallen Patriots Blowback CO2 Full Auto BB Rifle is probably one of the best looking AR’s in the Crosman series of Full Auto BB Rifles and I am happy to report the performance was as expected since I have done several Field Test Shooting Reviews for this series of BB Rifles. No you do not get a red dot with the Crosman R1 Fallen Patriots Blowback CO2 Full Auto BB Rifle but rather more old school iron sights but it really suits this BB Machine Gun and for me it didn’t hurt performance at all!
In this Field Test Shooting Video I test out the BARRA 400e Full Auto AEG 4.5mm BB Rifle to test out the velocity along with the accuracy and also get an idea on what the rate of fire is in Full Auto mode as on the box it claims 550 rounds per minute using what I would assume is a 7.4 volt battery. I wanted to test the BARRA 400e using an 11.1 volt battery but mine died on me. I will more than likely make a short video where I test out the 11.1 volt battery to see how this effects the rate of fire. If you want more information on specifications and details for the BARRA 400e then check my Table Table Video for it here.
Starting with testing out the Velocity for the BARRA 400e Full Auto AEG 4.5mm BB Rifle I shoot 6 rounds through my Chronograph to average out the fps and I was able to average 385 fps which is fairly close to the claimed 410 fps. Temperature does not effect an AEG as no CO2 is being used. Battery voltage also does not effect velocity as long as there is enough voltage to make the AEG motor pull the spring all the way back. Only trigger delay and rounds per minute are effected by battery voltage.
Moving on to my accuracy findings, I loaded up a full 50 round magazine and first unloaded 10 rounds fairly quickly into my paper target setup 30 feet down range shooting from a seated shooting position with the BARRA 400e resting on a sand bag up front. I was impressed to get close to a 1 inch 10 round grouping that placed just a little to the left and down from the bullseye right out of the box. I could easily center the sights as they are fully adjustable. I then switched the BARRA 400e Full Auto AEG 4.5mm BB Rifle to full auto and shot the remaining 40 or so rounds into the same paper target and even though the grouping opened up a little bit, it was not by much so accuracy in semi and full auto is very good with the BARRA 400e.
I have to say the rate of fire on the BARRA 400e Full Auto AEG 4.5mm BB Rifle using a 7.4 volt battery is rather slow even compared to other Airsoft AEG Full Auto Airguns but I still yet have to test it out using a brand new 11.1 volt Lithium battery so I do expect the rate of fire to improve a noticeable amount. Stay posted for that update video. Even with the slower rate of fire from the BARRA 400e this gun is awesome, it is really accurate and the velocity stays super consistent since CO2 cool down is not a factor. The mostly all metal construction and overall quality is very good and the fact that this is really the first commercial AEG 4.5mm Steel BB Rifle makes that alone a great reason to pick one up.
Starting with what the actual velocity of the KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol. I made sure to keep the Sea Can and Airgun nice and warm before making this test and I also placed a brand new 12 gram CO2 cartridge in it and went with lead pellets I am guesstimating where around 7 grain so not super heavy or super light, definitely not high velocity alloy pellets. I was a bit shocked that my average fps was no where near the claimed 360 fps. My 5 shot average came to 259 fps with a couple shots even shooting under 200 fps which I through out. Is that good enough for shorter range plinking? I would say so but but way off the claimed 360 fps. Maybe the manufacturers claim was using high velocity light weight alloy pellets?
Next as with all my Field Test Shooting Videos for the KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol I performed my accuracy portion of the test and reloaded the 16 round magazine which is actually a dual 8 round rotary magazine you manually switch sides to unload all rounds. My first 8 shots for the most part where decently centered perhaps a bit to the right but the grouping was rather spread out close to a around 5 inches maybe even a bit more. I then rotated the magazine to the other side of fully loaded pellets and this time I had several malfunctions/jams where rounds did not rotate properly therefore getting squished rather than going down the barrel. I have a feeling this is a problem with this specific magazine as I had the same problem during my Velocity test. I even switched to pointed pellets for the accrual test from flat head pellets but it did not seem to help. The best I could do on this day with this gun was to get around a 5-6 inch grouping which is not very good for a pellet shooter at 30 feet out
As I mentioned in the video I only test the guns, I don’t make them and as with any product out there it is possible I got a lemon since it seems to me like only one side of the rotary magazine was giving me the problems with jamming pellets. That said even the side that was more consistent did not shoot a very tight grouping for me. If it was my money to spend and I wanted a 24/7 styled Replica Airgun I would probably go with the blowback CO2 BB version since I had a lot better performance from that pistol with the addition of blowback action and a much lighter single action trigger.
In this Field Test Shooting Review of the KWC PM Makarov Non-Blowback CO2 Pellet Pistol I find out what the actual Velocity is and how accurately I can shoot it at a paper target setup 30 feet down range. If you have not already watched my Table Top Review for the KWC PM Makarov Non-Blowback CO2 Pellet Pistol then make sure to do so to see some nice closeup video of it and all the details and specifications laid out for everyone.
Starting with what the actual velocity of the KWC PM Makarov Non-Blowback CO2 Pellet Pistol. I made sure to keep it nice and warm before making this test and I also placed a brand new 12 gram CO2 cartridge in it and went with lead pellets I am guesstimating where around 7 grain so not super heavy or super light, definitely not a high velocity pellets. I was a bit shocked that my average fps was no where near the claimed 340 fps. My 5 shot average came to 263 fps with the highest being 272 fps and the lowest being 256 fps. Is that good enough for shorter range plinking? For sure but far off the called 340 fps. Maybe the manufacturers claim was using high velocity super light weigth pellets?
Next I performed my accuracy portion of the test and reloaded the 12 round magazine which is actually a dual 6 round rotary magazine you manually switch sides to unload all rounds. My first 6 shots I pointed the KWC PM Makarov Non-Blowback CO2 Pellet Pistol right at the bulls eye and found out it shoot a bit on the low side so only two rounds actually made it on the paper. I then switched to the other 6 round rotary magazine and aimed a bit higher, this time I was able to get fairly well centered on the target and produce about a 3 inch grouping. So in other words no awards are going to be handed out for this pistol in terms of accuracy or power. By the way I was using my standard shooting stance which is with my hands stabilized on a sand bag up front and sitting on a stool in the back.
The KWC PM Makarov Non-Blowback CO2 Pellet Pistol is not listed as any sort of target pistol so I was not expecting world class performance but I was expecting it to shoot a little bit better than your average blowback CO2 BB shooter and it really didn’t at the end of the day. If you’re specifically looking for a pellet shooting Makarov then this will be your Airgun since I am pretty sure it is the only one out there at this time but personally I would go with one of the CO2 Blowback BB versions since they shoot a bit harder and are maybe even more accurate not to mention you also get that blowback recoil with a nice light single action trigger.
Type: Pellet Air Pistol. Distributer:KWC. Model: KWC 24/7 TAC NBB Pellet. Materials: Metal and polymer build. Weight: 1.76 pounds (799 grams). Barrel: Rifled steel. Propulsion: CO2 x1. Action: Semi auto non-blowback, double action only. Ammunition Type: .177 caliber pellets. Ammunition Capacity: 16 rounds (2x8). FPS: 360-370.
Trigger Pull: The trigger pull on the KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol is a bit on the medium to heavy side so it’s not going to make for the best action shooter as it is a double action only shooter when compared to a single action only trigger or a single and double action trigger. As with most double action triggers it is a bit longer and slightly heavy but not unusable, just be prepared to get a little bit of a finger workout.
Accuracy: I have not shot the KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol just yet but will be doing so probably next week so stay posted for my Full Field Test Shooting Video for the KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol. I expect it to perform well in terms of accuracy and power since there is no blowback operation to have to compensate for. Having a rifled barrel should also help with accuracy! We will see shortly.
Build Quality: The KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol is built as expected just like all the other KWC Airguns. KWC has been making Airguns for a while not just for themselves but for other companies like Umarex, Gletcher, ASG, Crosman and even Sig Sauer and so quality control and durability have to stand up to these manufacturers standards. You will find metal on this gun where it matter. The slide, the full size drop out metal magazine and of course lots of internal parts. The frame, magazine release, trigger and safety are all plastic. I do like the feel of the rubberized grips for sure! Fit and finish is good overall and the fact that this is a fairly simple Airgun design with no blowback action or even a moving slide, so less moving parts means there is less chance for something to go wrong so it should last a while even with a fair amount of use.
Realism: The KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol shares it’s looks with the Taurus 24/7 but is not an exact replica. The trigger guard is a bit different and so is the placement of the controls and even the slide and frame are not exact but very similar. In terms of size, weight and vernal overall design for sure the KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol looks a lot like a Real Steel Taurus 24/7 at first glance.
Good weight and solid feeling gun. Lots of metal where you need it in the slide, magazine and other internals.
All metal full size drop out magazine holds CO2 and 16 pellets.
Decent looking replica (but not bang on) of a Taurus 24/7.
Not a lot of writing on the gun, very clean looking (Non Ranger version).
Recessed barrel helps with look of realism.
Fiber Optic front and back sights for easy sight acquisition.
Rifled barrel will help with accuracy.
Non-blowback operation with increased fps and CO2 efficiency.
Rail on top of slide and frame for lots of accessory add on options.
Double action trigger is long but not overly heavy so should be OK for action shooting.
Cons:
No blowback, slide is fixed and does not move but can be removed with a tool for internal access and cleaning.
No single action shooting so may not be the most accurate for slowed down shooting.
Sights are not adjustable but you can add an adjustable red dot to it using the rail setup.
Hard to tell when out of ammo, have to listen to the sound or count shots.
Comments:
It is nice to see more full size drop out metal magazine Replica Pellet Pistols coming out in the Airgun market just liek the KWC Makarov PM I just reviewed. Generally speaking most are going to be non-blowback but there are a few blowback options. That said a Non-blowback CO2 Pellet Pistol like the KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol will typically give you a high velocity and more shots per CO2 and can even be a little bit better in the accuracy department since there is virtually no recoil from them. The KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol is a nice little Taurus 24/7 looking Airgun that has a nice modern look and feel to it. Hopefully it performs well for me during my Field Test Shooting Video I will be making soon for it.
My Vimeo Videos for the KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol:
In this Field Test Shooting Video I test out the Umarex T4E HDX .68 Paintball Shotgun to find out what the actual fps is and if .68 Caliber Rubber Balls shot out of this Paintball gun are even going to be somewhat accurate at 30 feet out? If you have not already watched my Table Top Video where I go over the details and specifications with some closer up video showing you around the Umarex T4E HDX .68 Paintball Shotgun then make sure to watch it here…
Starting with the velocity portion of this video I used .68 caliber rubber balls which are not super heavy and not made out of a very hard rubber as you can squish them with your fingers fairly easily. I put 5 rounds through my chronograph after loading a pair of 12 gram CO2 cartriges into the CO2 chamber. My results averaged 206 fps which may seem slower than expected but they did hit my target pretty hard and actually knocked the cardboard backing right off of it. Each round was fairly consistent ranging from 203 to 210 fps.
Moving on to the accuracy portion of this test I proceeded to shoot around 10 rounds into my fresh paper target setup 30 feet down range. My target is basically an 8.5 x 11 sheet of paper and my goal was ot get all my shots onto the paper which I managed successfully. I would say most of the rounds all hit within about 5-6 inches of each other which for a Paintball Gun is very good! Keep in mind I was shooting using a seated position with the Umarex T4E HDX .68 Paintball Shotgun rested up front on a sand bag.
All in all the Umarex T4E HDX .68 Paintball Shotgun performed really well shooting consistent velocities and also getting all the rounds on an 8.5 x 11 inch target easily at 30 feet away which means if you where shooting at a persons body area you would easily hit it every shot making this a decent close quarters shooter which is what it really would be used for at the end of the day. Could you use it for less lethal home defense? I guess so especially if you can get your hands on pepper balls but I am not sure if regular rubber or paintballs balls would stop someone? Just seeing this impressive shotgun may in fact be more of a deterrent then being shot by it, but if it get’s the job done then why not.
In this Field test Shooting Video I Test out the Specna Arms Core SA-C07-PDW AEG Airsoft Rifle in the Replica Airguns Indoor Airgun Shooting Range to find out what kind of velocity we can achieve using standard .20 gram Plastic Airsoft BB’s. I also shoot 10 rounds in semi auto at my paper target 30 feet down range to see what kind of grouping I can get and then switch it over to full auto and let her rip till I am basically out of ammo and see if I can punch a nice hole in my cardboard backed target. If you are looking for more details and specification along with some closer up video then make sure to watch my Table Top Review Video for the Specna Arms Core SA-C07-PDW AEG Airsoft Rifle.
Starting with my velocity test, I shot 5 rounds through my Chronograph using .20 gram Plastic Airsoft BB’s with the preinstalled spring and got an average of 402 fps with my lowest velocity being 400 and my highest velocity being 405 so really close in fps. You can tone down the Specna Arms Core SA-C07-PDW AEG Airsoft Rifle a bit b y installing the M90 Spring if you find the fps to be a bit high for close quarter battles.
For the accuracy portion of this Field Test Shooting Review I proceeded to fire 10 semi auto rounds into a paper target setup 30 feet away. I use a semi rested shooting position with the Specna Arms Core SA-C07-PDW AEG Airsoft Rifle resting on a sand bag up front and me sitting on a stool for stability. My 10 shot grouping was all within around 1 to 1.5 inches which is very good for an Airsoft Rifle shooting lighter Plastic BB’s. I then switched the selector into “fun mode” (Full Auto) and proceeded to hold the trigger down until I ran out of spring tension on the High Cap Magazine. I would say I got through around 100+ rounds with most of them making about a 2 inch hole in my target consisting of cardboard and of course the paper target in front of it.
I have reviewed the Specula Arms line of Airsoft Rifles in the past, both the Core and the Edge and they really are great Airsoft Guns. The Specna Arms Core SA-C07-PDW AEG Airsoft Rifle as expected lived up to my expectations and performed really great in this Field Test Shooting Video. If you like this model also make sure to checkout the other models Specna Arms Offers over in our Replica Airguns Canada and US Online Stores.
Type: Pellet Pistol. Distributer:Umarex. Model:Stainless Ruger Mark IV. Materials: Metal and polymer build. Weight: 1.56 pounds (708 grams). Barrel: 5.3 inches (135mm). Total Length: 11 inches (279mm). Propulsion: Spring Piston. Action: SAO Break Barrel. Ammunition Type: .177 caliber pellets. Ammunition Capacity: 1 round. FPS: 320.
Trigger Pull: The trigger pull on the Stainless Ruger Mark IV Break Barrel .177 Cal Pellet Pistolis not too bad, I feel it is a around 6-7 pounds or so without measuring. In comparison to a real steel 22LR semi auto SAO trigger pistol, the trigger is much heavier but most of these 22LR pistols of this nature have what I would consider to be near perfect triggers. Over time once you get use to the pressure and release point accuracy with this pistol it is for sure possible.
Accuracy: I have tested out the all black version of this pistol which will perform exactly the same or should I say is expected to perform the same since they are virtually the exact same Pellet Pistol but in different finishes. You can watch my Field Test Shooting Video for the all black version but in case you don’t make it there I will fill you in on the basic results… In terms of velocity I averaged 312 fps using 7 grain lead pellets and got around a 2 inch 7 rounds grouping but expect with a bit more trigger time to get closer to 1 inch.
Build Quality: The Stainless Ruger Mark IV Break Barrel .177 Cal Pellet Pistolis a low cost target plinker that also doubles as a licensed Replica for that coolness factor so you won’t get an all metal super top quality build here. That said metal and plastics are well used and for sure details in the fit and finish have been improved over the Buck Mark URX version where I found the barrel felt a bit sloppy and the trigger was plastic. The Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistol has a much tighter barrel fit when closed and the trigger is now metal! Maybe Umarex watched my video back in the day and took some notes?
Realism: The Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistol most resembles the Mark IV Hunter edition and is pretty much bang on in terms of being a replica other than the tell tail hinge just under the barrel required for a spring piston design, there really is no way to get around this so I’m not going to criticize this minor difference. The real steel version is almost 3 pounds and so the pellet shooting version is a bit under weight so it would have been to have had more metal perhaps in the barrel and lower frame. Again since the pellet shooting version is a springer you will not have any working bolts or slide catches or a built in magazine.
Pros:
It's a decent Ruger Mark IV Replica!
Feels well built overall.
Expect it to have really good accuracy like the Umarex Browning Buck Mark URX since they share similar mechanical design.
Barrel locks into place much better than the Umarex Browning Buck Mark URX did.
Fully adjustable rear sight with fiber optic front sight.
Auto locking safety, just don’t forget to unlock before each shot
Actual metal trigger in this version.
Nice and compact, not too heavy.
Full Ruger licensed via Umarex.
Fairly low price tag.
Cons:
No built in rail for a sight system like the Umarex Browning Buck Mark URX.
Would have liked a metal trigger and maybe a slightly lighter trigger pull to match the real Buck Mark's very light trigger pull.
A bit more metal would have been nice.
Significantly more expensive than the black version which is the same exact gun in a different color.
Comments: The Stainless Ruger Mark IV Break Barrel .177 Cal Pellet Pistol is a decent looking replica and a decent pellet shooting target pistol and if you own the real steel version in 22LR you may just want to get your hands on one of these Break Barrel Replica Pellet shooters. The only real question is do you get the Stainless version with simulated wood grips or the all black version? If you like the look of the stainless version and don’t care about money whatsoever, then pickup that one up since it is a Limited Edition version that will only go up in value over time. If you are on a budget and don’t mind the look of the all black versions or maybe even prefer it then by all means grab one since at the end of the day they will both perform exactly the same.
My Vimeo Table Top Review Videos for the Umarex Stainless Ruger Mark IV Break Barrel .177 Cal Pellet Pistol:
Type:Airsoft pistol. Distributer:Umarex. Model:Smith & Wesson M&P 9L. Materials: Metal and polymer build. Weight: 1.7 pounds (757 grams). Barrel: 4.75 inches (121mm), non-rifled. Total Length: 8.5 inches (215mm). Propulsion: CO2 x1. Action: Semi auto blowback, single action only Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 15 rounds. FPS: 410 Claimed.
Trigger Pull: The trigger pull on the Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol is fairly light weight being a single action only trigger. There is about a quarter inch of take up with an easy release that is not hitchy at all. You will need to rack the slide to load your first Airsoft BB into the breach and engage the action but on the first shot but then the blowback action does this for you until the Airsoft Pistol is out of ammo and the slide locks back.
Accuracy: I have not performed my Field Test Shooting Video for the Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol so stay posted for that video coming out in the next couple of weeks. Umarex has claimed a velocity of around 410 FPS using .20 gram Airsoft BB’s but that does seem a bit quick, well will have to see when I place some shots though my Chronograph! In terms of accuracy I expect it to shoot about the same as most Full Blowback Airsoft Pistols which generally produces a 1.5 to 2 inch 10 shot grouping from 30 feet out using a semi rested shooting position. Again we will find out when I perform my Field Test Shooting Video for the Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol.
Build Quality: The Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol build quality is fairly decent, fit and finish looks good with not too much slide wiggle and the materials used are both metal and plastic or polymer that look to be good quality. I do expect some of the black finishes ot come off on the high spots as these guns are generally electroplated and not too thick with it but this can actually make the gun look more realistic with that slightly worn in look to it.
Realism: The Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol in terms of looking like the real steel version of its counterpart is very close for sure, it would be hard to tell without really taking a close look t it. Everything about this Replica Pistol works for the most part like the real steel version including most of the mechanical parts like the slide catch release, magazine release, take down lever, trigger safety and you can even fully field strip it which gives you easy access to the hopup on the barrel. Of course the full blowback action really seals the deal in terms of making this gun shoot like a real semi auto pistol.
Pros:
Very accurate replica of the S&W M&P 9L.
Fairly accurate weight and feel to it.
Metal and plastic parts where you find them on the real steel version, fit and finish is good.
Working trigger safety and ambidextrous working slide catch release.
Full size dropout metal magazine that holds Airsoft BB's and CO2.
Warning instructions are discreet under the trigger guard.
Recessed barrel and hidden CO2 screw for more realistic look
Fully Smith & Wesson licensed via Umarex.
Rail for add on accessories.
White dot sights for easy target acquisition.
Comes with three sizes of interchangeable grips S/M/L.
Adjustable hopup so you can at least adjust elevation at range.
Comes in a box rather than a clamshell.
Cons:
Has an orange tip but could be painted black or silver to match.
Sight are not adjustable.
15 round magazine has less capacity than some other blowback Airsoft Pistols.
Comments: The Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol is a nice addition to the Smith & Wesson M&P line of Replica Airguns. I’m glad they made it in full blowback but being Airsoft based that is generally the way they lean towards. Hopefully we get to see 4.5mm Steel BB version too in the future! For now we have it in Airsoft and with the longer barrel perhaps it will shoot a bit hotter than most of the other CO2 Blowback Airsoft Pistols, maybe even 410fps like Umarex claims but I will be surprised if it does. I will be happy to see something in the high 300’s to be honest. No matter what, you now have yet another Smith & Wesson option to consider when looking for your ultimate Replica Airgun!
My Vimeo Videos for the Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol
Starting with my velocity test, I shot 3 rounds through my Chronograph using .177 caliber 7 grain lead pellets achieving 482, 489 and 466 fps with an average of 479 for the three shots. Not bad for a fairly compact Break Barrel Airgun. This is perhaps fast enough for small game like mice and small rats but you would need to get proficient on your shot accuracy to make sure you got a good head or lung shot to make it a more humane pest control.
For the accuracy portion of this Field test Shooting Review I proceeded to fire 6 rounds into a paper target setup 30 feet away. I use a semi rested shooting position with the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun resting on a sand bag up front and me sitting on a stool for stability. My 6 shot grouping was all within around 1.5 inches but I feel like this Pellet gun can do better with me getting a bit more use ot it, still not bad out of the box and with my first round shooting it.
I really like the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun as not only a Replica but it also shoed itself ot be a decent target Airgun at the end of the day. I do have to say the trigger is a bit long but not heavy at all, it has a smooth pull with a soft release. Most pimple should be able towel with this just fine. SO if you are looking for a Replica but also want an Airgun that can shoot hard and with decent accuracy then look no further than the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun.
In this Field Test Shooting Video Review I test out the brand new Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun in the Replica Airguns Indoor Airgun Range Sea Can to see what the actual velocity is along with accuracy. I first test fps using my Chronograph and I perform this test with and without the barrel extension to see how much the additional barrel length will increase velocity. I also shot the Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun in both semi auto shooting 10 rounds into my paper target setup 30 feet down range and then I perform a full auto 25 round magazine dump to see if the grouping expands or not.
Staring with the velocity test I did use brand new CO2 for this and the temperature was around 20 degrees Celsius or 68 Fahrenheit so not too cold or warm. With the Barrel extension installed I managed to average 418 fps shooting 4 rounds. With the barrel extension removed as expected the velocity did drop a bit down to 373 fps shooting 4 rounds and averaged out.
For my Accuracy Test I placed the Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun in semi auto for the first portion and fired 10 shots into the paper target setup 30 feet away, I was using a semi rested shooting position with a sand bag up front to rest the gun on and me sitting on a stool in the back. I did not sight the red dot in and found that out of the box the Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun shot down and too the right a fair amount but at least I was able to get most of the shots on the paper target and on camera. The grouping was around 2.5 to 3 inches so not super great but not bad either.
I then flicked the main selector to Full Auto since this is what most people want to see. I also reloaded the magazine with 25 rounds from the onboard hopper and unloaded the full magazine in a second or two. I did aim a bit higher and to the left this time to get the shots closer to the bullseye and I was able to do so with most of the 25 shots all within about 2.5 to 3 inches so not really any difference shooting in semi or full auto at least in terms of accuracy.
As I mention before in my Tabel Top Review for the Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun, it is a bit different looking and for me took a bit of getting use to but the good news is that it performs about the same as the other Crosman CO2 Full Auto Blowback BB Rifles in this similar lineup so if you like the look then don’t be afraid to pick one up over on our Canada or US replica Airgun Stores.
Type:Pellet Rifle. Manufacturer: Umarex Model:HK MP7 .177. Materials: Metal and Polymer. Weight: 4.4 pounds (2kg). Barrel: 11.7 inches (29.7cm). Total Length: 31 inches (78.7cm). Propulsion: Break Barrel Spring Piston. Action: Single Action Single Shot. Ammunition Type: .177 Caliber Pellets. Ammunition Capacity: 1. Max FPS: 490 Claimed.
Trigger Pull: The trigger on the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun is single action only requiring you to break the barrel and compress the internal spring piston before you can shoot it. The actual trigger pull is pretty decent overall. There is very little take-up but the creep is on the longer side but fairly smooth requiring medium pressure. The release is a bit hard at first to predict but nothing some trigger time can’t get you use to.
Accuracy: I have not performed any shooting tests with the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun so far. I hope to make that Video Review next week. I expect the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun to perform well in the accuracy department especially with the included Red Dot Optical Scope installed. I hope the velocity rating from Umarex is based on lead pellets and not hyper velocity light weight pellets but we will find out the story when I perform my Field Test Shooting Video shortly!
Build Quality: The Umarex HK MP7 .177 Cal Break Barrel Pellet Gun is a China made Airgun but looks to be well made. It has lots of metal parts as you would expect from a Spring Piston Rifle which adds a nice weight and feel to it. I did however have an issue with the front plastic mock Suppressor/Compensator as it does not seem to be attached to the metal barrel very well other than being pressure fit which is not going to cut it with all the vibration a spring piston system makes. My first shot loosened the mock Suppressor/Compensator so I will either have to hold it when shooting or find another way to make sure it stays in place.
Realism: The Umarex HK MP7 .177 Cal Break Barrel Pellet Gun is kind of unique in this department as most break barrel rifles are not Replicas, especially the more compact sub machine gun styled ones. Umarex did good job making the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun look like a real HK MP7 for the most part. Of course it is a Spring Piston Rifle at its core so exceptions had to be made to make this work including molded non working parts like the magazine release, sector switch and, bolt/ejection port. That said all in all it is a decent looking replica considering it is a Break Barrel Airgun under the skin.
Pros:
Not many Replica Pellet Rifles on the market, especially in a more compact gun.
Comes with Red Dot sight.
Lots of rails for adding accessories to it.
Full HK Licensed by Umarex.
Collapsible Wire Stock.
Nice high claimed 490 fps.
No need for CO2 so low cost to cooperate.
Not effected by temperature like a CO2 Airgun.
Should have better accuracy than most BB Replica Airguns.
Very solid feel to it, good overall weight and feel.
Cons:
Not going to be an action shooter, have to reload after each shot.
A good overall Replica but not as Realistic or full operation as a BB version would be.
Mock Suppressor/Compensator poorly attached to barrel.
Comments: The Umarex HK MP7 .177 Cal Break Barrel Pellet Gun is an interesting product, on one hadn't it is a Replica Airgun and most people expect a Replica Airgun to have all of the appropriate working parts similar to what would be found on the real steel version. But since this is a Break Barrel Airgun at the core the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun will not function the same as the Real Steel version so as long as you don’t expect it to and appreciate the fact that it should be a nice accurate low cost to operate target rifle then I think you will understand this product and enjoy it for what it is… A Single Shot Pellet Rifle that looks a lot like a HK MP7.
Type: BB Rifle. Manufacturer: Crosman. Model: ST-1. Materials: Metal & plastic. Weight: 6.07 pounds (2.75 kilograms). Total Length: 17.75/33 inches (Pistol/Rifle). Barrel Length: 15.5 inches. Propulsion: 12 gram CO2 dual cartridges. Action: Blowback - single action only. Ammunition Type: 4.5mm steel BB's. Ammunition Capacity: 25 Round/Spring - 300 Round/Hopper. FPS: 480fps. Rate of Fire: 1400 rounds per minute in full auto
Trigger Pull: The trigger pull on the Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun is single action only since the right side charging handle must be cocked first before you can shoot it to engage the action. The trigger is short and fairly light but not overly light. The real fun happens with the Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun when you switch it over to full auto mode and with just one pull and hold of the trigger you empty the 25 round magazine in a mere matter of seconds at 1400 rounds per minute.
Accuracy: I have not actually shot this BB Rifle to date but expect it to get similar results to the other Crosman Full Auto BB Machine guns I have already reviewed. I am expecting a bit more velocity with the longer barrel extension installed and would be happy if I was able to get in the mid 400’s. Accuracy should also be about the same with 1 inch semi auto groups from 30 feet out expending a bit when in full auto.
Build Quality: The Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun is well made all around. Weighing in at 6.07 pounds without any add on accessories other than the included compact Red Dot sight. It feels solid and well built. There is a lot of metal going on inside and out of this rifle but keep in mind the top and bottom receiver are plastic with metal parts where they need to be like in the internals, pretty much all the working parts are metal, the magazine is full metal, the buffer tub is metal, charging handle, selector switch, magazine release, bolt release, trigger and of course the barrel is metal.
Realism: The Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun is not modeled after any real steel gun I know of. It resembles a futuristic weapon you would see in a SciFi Action Movie or Alien First Person Shooter. I was not a fan of it when it was first released by Crosman but after seeing and holding it in person it is growing on me quickly.
Pros:
Very unique, not like your regular Replica Rifles, very futuristic in design.
Drop out magazine doubles as the 300 round hopper and holds CO2 and BB’s.
Comes with Red Dot Sight and lots of rails for mounting what every you want on it.
Can be either a Pistol or Rifle or a PDW by adding or removing the Barrel Extension and Rear Stock.
Barrel Extension actual lengthens the barrel and should increase fps, not just for show!
Tactile comfortable rubber padding in multiple locations.
Semi auto and full Auto selectable.
Expected higher fps of up to 480.
Cons:
Some people may not like the look? Not like your normal modern rifle.
Front rubber grip comes off really easy at least on mine?
Will require barrel extension for full velocity.
Comments:
The Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun is a brave move by Crosman, I was not expecting something like this from them and when I originally saw it I was not sure if it was a good idea or not but again once seeing it in person and actually holing it I feel a lot better about it. It will for sure appeal to those looking for a futuristic Airgun or wanting something that looks like a gun from a video game or SciFi movie. I also like the versatility you have with the Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun being able to configure it how you like either as a Pistol, full on Rifle or PDW style shooter.
My Table Top Video of the Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun:
Sights for guns in general are the same for Airguns as is with real steel guns for the most part and can be mixed and matched with a couple of exceptions. Spring piston rifles for instance are an exception because of the unique vibration the spring makes and how it can damage a standard optical sight, so in this case you’re best to use an optical sight designed for a spring piston Airgun. In most other cases sights can be used on all types of guns.
In this Airgun Sights video I will go over the various types of sights that either come as part of the gun design or can be added afterwards using a rail or mounting system.
Types of Airgun Sights most commonly used.
Iron Sight (Fixed or removable).
Iron Sight (Adjustable).
Iron Sight (White Dot, Fiber Optic).
Come in Post/Notch, Post/Aperture (Peep).
Common on Pistols and Rifles
Laser Sight:
Generally added to a rail or can sometime be integrated into the design of the gun.
Common on both Pistols and Rifles.
Red DotandHolographic:
Generally not magnified.
Most common on Rifles but can be used on Pistols.
Optical Magnified (Telescopic)
Come in a variety of magnifications for different shooting ranges.
