Entries in How To,Q&A Video

How Did Replica Airguns Come to Be?

No Comments

I am personally very interested in what the origins of a company are, at least companies that I am interested in. Where did the idea for the company come from,? How did the company first start up? What steps did they take to get to where they are now? Where there any road black along the way?

I don’t believe I have every talked about how Replica Airguns came to be in any of my videos, where and when it all started, so why not talk about it now…

And I don’t have any Airguns to review at the moment so I need to make a video of some sort…

Categories: Replica Airguns News, Q&A Video, Vimeo Video Tags:

Reasons why Replica Airguns are Better than Real Guns

No Comments

Cost:

Airguns are generally cheaper to buy and for sure cheaper to shoot. Airguns can cost as little as $50-100 to buy while real guns in similar models will cost many time more. Cost of ammo is so much less expensive than Real Gun ammo by a mile!

Difficulty to Obtain:

Airguns in most countries do not require any licensing or registration. Generally there are more available options in Airgun choices than Real Gun choices as restrictions often prohibit many Real Guns to be obtained.

Places to Shoot:

Unless you live in a super remote locations and your laws allow you to shoot Real Guns in those locations, then in most cases you can shoot an Airgun almost anywhere within reason. You can even shoot certain Airgun models in your basement. Airsoft is a great option for indoor shooting as the plastic ammo does not carry very much energy so with minimal effort you can make a backstop that will trap the ammo very well.

Trigger Time:

Because ammo is much less expensive and places you can shoot are easier to find, you can get a lot more Trigger Time under your belt which will also improve your shotgun with Real Guns and after all it’s just fun to shoot guns even if they are Airguns.

Safety:

I am not talking about safety in terms of protection. I am talking about safety as in if you do something stupid and your Gun goes off accidentally. If you accidentally fire your Airgun indoors, the bullet will not travel through floors or walls and potentially harm or kill someone on the other side. If you do manage to shoot yourself with an Airgun, the consequence are much less severe than shooting yourself with a Real Gun. That said, always treat an Airgun as if it was a Real Loaded Gun, as server injury and even death can occur even with an Airgun.

Ware Games and Training Situations:

There is no way you can use a standard Real Gun to shoot at people, unless extensively altered with special parts that make the Real Gun unusable to shoot live ammo. With Airguns you have the choice of using an Airsoft or Paintball gun that are both designed specifically for this purpose.

Pest Control:

If you have the need for pest control in an urban area where you do not want a stray bullet to travel too far or penetrate buildings if a shot where to go awry, then an Airgun designed for accuracy and power may be perfect for the job. Accuracy with target and hunting Airguns is on par if not better than many Real Guns and are have powerful enough to kill a pest humanely without having too much power for the job and having to worry as much about your background.

Prop Guns:

As mentioned already, Airguns can look a lot like Real Guns, so they are perfect to be used as a stand-in or Prop Gun when you need to simulate the look and function of a Real Gun. Again they are easier and cheaper to obtain and if something does go wrong, the consequences are much less severe.

Social Stigma:

Unfortunately Real Guns and perhaps any gun these days are looked upon with a social stigma as being the cause of the Crime rather than a tool used in a Crime. And so people blame Guns for these crimes rather than the people committing these crimes. If a person is motivated enough to do something bad, they are going to do it either way and will use whatever means is available to them to commit these Crimes. Including other means like: Knives, Blunt Objects, Poisons, Vehicles, Explosives… Sad but true! Airguns are not used in homicides or mass shootings as they are completely underpowered for a crime like this. They can however be used in crimes as a show of threat, as they do look a lot like real guns, generally people that use Airguns for real crimes, if challenged will give up immediately as they are completely outgunned. Don’t bring an Airgun to a Real Gun fight, you have better chance with a knife!











Categories: Comparison, Gun Safety, Pistol, Real Gun, Rifle, Vimeo Video, .20 cal, .22 cal, .43 cal, .50 cal, .68 cal, 10mm, 380, 4.5mm / .177 cal, 6mm, 8mm, 9mm, AEG, Airsoft, BB, Blowback, Break Barrel, Bulk Air, CO2, Full Auto, Gas, GBB, Gun Law, Non Airguns, Paintball, PCP, Pellet, Pump, Q&A Video, Repeater, Revolver, Semi Auto, Single Shot, Spring Piston Tags:

Airgun Magazine Types Explained - BB - Pellet - Airsoft

No Comments

There are many types of magazines used in Airguns and some of this is dependent on the ammunition used.

For instance a stacked type of magazine often used for Steel BB and Airsoft can not be used for Pellets as pellets tend to deform when stacked in such a way since there is no metal casting protecting them from mashing into each other.

So what type of magazines do we generally see in Airguns? The most common Airgun magazines are as follows:

Simple Stick Magazine

  • Mostly used with Steel BB but also found in some Airsoft Airguns.

  • Some Pellet Airguns use a type of stick magazine with a rotary magazine on each end.

  • Used in non-blowback and blowback Airguns.

  • Can be made from plastic or steel or a combination of both materials.

Full Size Drop Out Magazine

  • Used with Steel BB and Airsoft guns.

  • Generally you will find these types magazines hold both the BB’s and CO2.

  • Used in non-blowback and blowback Airguns.

  • Commonly used with Airsoft Rifles in mid to high capacity.

  • Can be made from plastic or steel or a combination of both materials.

Rotary magazine

  • Used with Steel BB, Airsoft and Pellet Airguns.

  • Used in non-blowback and blowback Airguns.

  • Can be made from plastic or steel.

  • Can often use mixed ammo types as in both 4.5mm Steel BB and .177 caliber pellet.

Belt Fed Magazine

  • Like rotary magazine belt fed magazine can accommodate Steel BB, Pellet and Airsoft but are most often used with Pellet Airguns.

  • Usually found in a full size magazine that also holds the CO2.

  • Used in non-blowback and blowback Airguns.

  • Can be made from plastic or steel or a combination of both materials.

Internal Magazine

  • Used with Steel BB, Airsoft.

  • Can have a hopper built in hat feeds a spring fed magazine.

  • Usually found in lesser expensive Airguns but not a rule.

In this Video I go through each type of Airgun Magazine and talk about their differences and uses.

Categories: 4.5mm / .177 cal, .22 cal, 6mm, AEG, Airsoft, BB, Blowback, CO2, Comparison, Bulk Air, Gas, GBB, How To, Pellet, Pistol, Review, Revolver, Rifle, Vimeo Video Tags:

Replica Airguns Frequently Asked Ammunition Related Questions

No Comments

In this video I answer some commonly asked questions I get in many of the comments section about Airgun ammunition.

Here is a list of the topics I go over in this video:

  • Can you remove a partially used 12 gram CO2 cartridge once you use it?

  • Can you reuse a CO2 cartridge?

  • Why is FPS consistency so inconsistent with CO2 cartridges?

  • What is the difference between Green Gas and CO2?

  • Why do pellet firing Airgun magazines not lock back after the last shot?

  • Can you use steel BB's in an Airsoft gun and plastic BB's in a BB gun?

  • What is the difference between (4.5mm and .177 caliber) and (6mm and .22 caliber)?

  • What is the difference between hypervelocity pellets and standard lead pellets?

  • What is the difference between copper coated steel BB's and zinc coated steel BB's?

  • What are the best pellets to use? Wad cutters vs domed vs hollow point vs pointed?

  • What is the best weight pellet to use with my Airgun?

Categories: Q&A Video, YouTube Video Tags:

Is an Airgun Good for Self Defense Revisit

No Comments

A while back I made a Vimeo Video named” Is an Airgun Good for Self Defense?” It’s been pretty popular on YouTube getting over 2 million video views and I get a lot fo feedback from my viewers with varying opinions on this issue. I like constrictive feedback and enjoy hearing what my YouTube viewers have to say as long as everyone is being civil about it and not just trying to start an argument.

In my first video on this subject I pretty much go on the record saying I don’t think Airguns are a good choice for self defense and there are for sure way better alternatives but many of you disagreed with me and so I decided to make this update or revisit video and go over some of the top pushback comments I get and see if they have some merit to them.

Here are the top 4 pushback comments I get the most often:

  • When the bad guy sees the airgun they are going to run away thinking it’s a real gun.

  • Just shoot the bad guy in the eyes / face.

  • Use an HPA large caliber rifle.

  • Use a full auto high capacity Airgun.

Watch my “Is an Airgun Good for Self Defense Revisit” Vimeo video to see how I address these pushback comments.

Categories: YouTube Video, Q&A Video, Gun Safety, Gun Law Tags:

Which is Better - Plastic or Metal Airguns?

No Comments

We often think that something that is more expensive and perhaps built with what we consider to be better materials is going to be the best option. That's not always the case! In this Vimeo Video I talk about some of the Pros and Cons to buying a Plastic Airgun versus a Metal Airgun. Of course this applies to BB, Airsoft and Pellet shooters.

Price
In most cases a Plastic Airgun is going to be less expensive, so if you have limited funds then your only option may be a Plastic Airgun and at the end of the day both airguns are going to probably get the job done much the same.

Realism
Generally speaking, most Metal Airguns are going to have more moving parts, often times with working slides and even blowback operation. This is not always the case but even a Metal Airgun that has few working parts will still feel more realistic simply because of the additional weight to the Airgun. Metal has that cold hard feel to it that makes you feel like you're holing something of substance. Plastic Airguns on the other hand can feel light and cheap and usually are very simple in design with less working parts.

Shooting an Airgun with blowback operation simulates the recoil action and in many cases allows for true single action operation of the trigger and hammer. This is going to feel a lot more realistic than shooting a non-blowback Airgun which again is generally what you get with Plastic Airguns.

Durability
Most people assume that because an Airgun is Meta, it is going to be stronger and more durable. This would be true if the Metal used in the Airgun was actually hardened steel but with almost Metal Airguns, they are made using a zinc alloy metal (Pot Metal) that is much softer then hardened steel and can wear and break a lot easier. When you also consider a Metal Airgun is going to be a lot heavier than a Plastic Airgun, a drop onto a hard surface will have a lot more impact which can cause breakage a to a heavy Metal Airgun versus a Plastic light weight Airgun.

Plastic surfaces are also a lot less prone to showing scratches since the Plastic material will usually be black all the way through versus a Metal Airgun that has a painted surface that when scratched hard enough will show through right to the bare metal. You also get wear marks on painted Metal Airguns that will make it look used and older, some people like this look but other do not.

Reliability
Again people are going to assume a Metal Airgun is going to be more reliable simply because it has more metal parts and metal parts are stronger right? Not the case if the parts are made out of zinc alloy. Now some companies will upgrade some high use parts in Airguns to hardened steel but it's hard to know for sure. You can use a magnet to determine what parts are Metal and what parts are hardened steel.

As we mentioned before, Plastic Airguns are generally pretty simple in design, less working parts means less to go wrong at the end of the day so just because you have a Plastic Airgun it doesn't mean it's going to break on you quickly. Actually it may even outlast your Metal Airgun since all those working parts will eventually wear out.

Now I am the first person to admit that I prefer Metal Airgun over Plastic Airguns, I don't mind spending the extra money for more realism and I'm willing to accept the fact that it's not going to last forever but the fact remains, a Plastic Airgun does have some advantages going for it so don't rule them out completely.

Categories: 4.5mm / .177 cal, 6mm, AEG, Airsoft, BB, Blowback, CO2, Comparison, Full Auto, Pellet, Pistol, Q&A Video, Revolver, Rifle, Semi Auto, Single Shot, YouTube Video Tags:

The Best Way to Hold Your Airgun

No Comments

I made a similar video about how to hold your airgun a while back but sometimes they get a bit buried in all the video I make. I feel it's really important how you grip your gun even if it's only an airgun with very little kick or recoil. Proper pistol grip is something you should use no matter what so that you can carry it forward to what ever gun you are shooting.

More kick or recoil means a firmer grip is required to hold the gun so when shooting a powder burner with lots of kick grip becomes even more important.

In this video I go over the proper two handed grip to use when holding a pistol, which hand to hold lose and which had to grip tight, how to overlap your fingers and thumbs.

Categories: Airsoft, BB, Break Barrel, CO2, Blowback, How To, Non Airguns, Paintball, Pellet, Pistol, Real Gun, YouTube Video Tags:

Why is My CO2 Airgun Not Working?

23 Comments

One of the most common types of question I get on my Replica Airguns YouTube channel has to be something like… Why is my Airgun not working? Most of the time the amount of info about the problem is limited to something like… “It was working yesterday but now it’s not working anymore” or something like “when I pull the trigger nothing happens”. My personal favorite is… “I took my gun apart and now it doesn’t work!”

I just made a similar video for Blank Guns and as I said in that video, trying to trouble shoot a mechanical or technical problem over the internet is very difficult, this goes for cars, guns, computers or what have you…

In this Why is My CO2 Airgun Not Working video I will however cover some of the more common and obvious problems I have seen relating to why a CO2 Airgun may not be working properly. I really don’t get a lot of questions about Spring Piston or Pump Airguns so I will be focusing on CO2 Airguns in this video. There will be a lot of crossover with CO2 Airsoft guns so this video may be helpful for some of you Airsofters out there

First let’s get the super obvious stuff out of the way! 

  • Did you put a new CO2 cartridge in it and is it pierced all the way?

  • Did you load BB’s or Pellets into the Airguns magazine and is the magazine in the gun correctly?

  • Is the safety off?

  • If the gun is a blowback semi auto single action Airgun then did you pull the slide back prior to the first shot?

CO2 Related Problems:

Not all CO2 cartridges are created equal, they often have slightly different shaped nubs on them and some brands will work better than others in different Airguns. If the shape of the CO2 nub does not fit properly into the valve area then it may not pierce or it could pierce but then not allow you to tighten it all the way losing all the CO2 in the process. If the CO2 is coming form the airguns handle to CO2 Valve area then this is an indication that your problem is related to the area where the CO2 enters the airgun.

There is a seal where the CO2 cartridge buts up to the valve, this seal can be damaged or even deformed from usage or even leaving your CO2 in the gun for too long. The outside CO2 Valve seal can also take the shape of a specific CO2 nub so when you use a different brand CO2 the seal may not properly make concat with the new CO2 type you are using, again causing leaking or even the total loss of all your CO2. Watch my YouTube video on “How to Fix Leaking CO2 in an Airgun”.

CO2 Valve Related Problems:

Again, make sure that Outside CO2 Valve Seal is in good condition and any leaking is not being caused by this problem, if you have checked the Out Side Seal and everything is OK with it then perhaps there is a problem with the CO2 valve?

One indication that your CO2 Valve might be the culprit is the total loss of all your CO2 when you try to insert and tighten a new CO2 Cartridge. Usually all the CO2 will exit the barrel, not the handle or valve area. What may be happening is the valve is stuck open or the internal seal is broken or deformed. If this is the case you will have to remove the valve and have a look inside, this is a lot easier on CO2 airguns that have the CO2 valve in the magazine, if the CO2 valve is in the actual Airguns then a lot more disassembly may be required and I would recommend an Airgun technician take care of this for you.

If the gavel is in the magazine then you will have to unscrew it, you may require a special tool for this? Once the valve is out of the magazine  take a look inside and examine the internal seal, also look for any bits of metal shavings as they can disrupt the action of the valve causing leaking. Give the inside of the valve a good clean and then lubricate it with some silence spray. hopefully that fixes your problem!

BB’s getting Stuck in the Blowback Gas Tube:

I have actually made a dedicated video for this problem so I will put a link to it in the description of this video. The main reason people may have this problem is because we all like to rack that slide on our full blowback Airguns, but if you have a fully loaded magazine then each time you reach that slide without shooting the gun, you are inadvertently trying to load another BB into the breach area, the breach is only designed to hold one BB at a time so after a few racks of the slide the newly loaded have no place to go but into the Gas Tube where they can get stuck and cause having to the operation of your Full Blowback CO2 Airgun.

BB’s Rolling Out of the Barrel of Your CO2 Airgun:

This is not actually a fault of the gun but happens because of the way the gun is designed. This situation can happen with certain CO2 Airguns when the gun user pulls the trigger really slowly while the gun is point slightly in a downward position. What is actually happening is the first part of the trigger is made to draw a BB from the magazine into the breach of the gun. If the barrel of the gun does not have a rubber hop-up stopper in it then the BB is free to roll down the barrel and out of the gun. How do you fix this problem? Be more committed to your trigger pull and or shoot at a target that is not so low. Perhaps place your targets slightly higher than the gun so the barrel is not pointing down, especially if you like to take your time with the trigger :)

A Little Maintenance Can Go a Long Way!

Sometimes a good cleans is all you need to do to get things working as they should, again I have already made video Tutorial Showing “How to Clean Airguns and Blank Guns”.

What about stuff like My Airgun is jammed or my trigger is stuck or some random part fell out of my gun?

There is only so much I can cover in this video, most other problems are going to get a bit more complicated to fix and I suggest if your Airgun is not working and the suggestions I have made in this video do not solve your problem, then consider taking your gun into a gun tech.

Categories: 4.5mm / .177 cal, 6mm, Airsoft, BB, Blowback, CO2, GBB, How To, Pellet, Pistol, Review, Semi Auto, YouTube Video Tags:

Why is My Blank Gun Not Working?

6 Comments

First off I want to say it’s hard to trouble shoot technical or mechanical problems over the internet regardless of if ithas to do with guns, cars, computers or pretty much anything where unless you are there in person it’s really hard to figure out the problem.

But I will attempt to address some of the more common issues why a blank gun may not be functioning properly.

Why is my Semi Auto Blank Gun Not Cycling or Ejecting Shells?

One very common reason a blank gun may not be cycling the shells properly is because the owner has removed the barrel restrictor plug. People usually do this to make the barrel opening look more realistic but the barrel restrictor is a necessary component to increase the back pressure allowing the slide to cycle fully to the rear position so it can eject and pickup a new shell.

The blanks you are using may not have enough gun powder in them. Some blank guns require banks with more gun powder than others, again this additional internal pressure forces the slide all the way back, if the blank does not have enough gun powder in it then only a partial slide motion happens and so the discharged shell may not eject properly, in this case the user would have to clear the blank gun manually so another shell can then be picked up and loaded into the breach.

If your blank guns is dirty or not lubricated then it may act sluggish again restricting the full movement of the slide which will effect correct operation. Make sure to thoroughly clean and lubricate your blank gun, that may be a quick fix for you!

You may have a faulty extractor? The extractor is like a hook that grabs the discharged shell while the slide is in the reward position pulling or extracting the shell out of the breach. If the extractor is worn or broken then the empty shell will not be ejected from the breach so when a new shell is picked up from the magazine it has nowhere to go and usually you will get a jam-up in the ejection port area.

One final situation that can cause your blank gun to not cycle properly is to strong of a slide spring, some blank guns out of the box just come with a really heavy slide spring, so much so that even blanks with lots of gunpowder in them are still not strong enough to make the slide operate full motion. Your only option here would be to replace the heavy slide spring with a lighter one.

Why Are My Blanks Not Firing?

This is a situation where you pull the trigger and nothing happens. Lets get the obvious causes right out of the way here… Did you put blanks in your gun and are they new blanks? Did you chamber the first round in your semi auto pistol?

So now that that’s out of the way let’s look at some other reasons why your blank gun may not be firing a blank. Perhaps the firing pin is broken? Most blank guns are not made out of carbon steel and even the firing pins can be lesser quality than what you would find in a real gun so blank guns are more prone to breaking than real guns. I have seen broken firing pins in blank guns first hand so make sure to check the firing pin and that it is fully operational.

Try changing up your blanks to another brand? Again blank gun ammunition is not made to the same higher standards that real firearm ammo is made and some primers may require a little more pressure than your gun is providing. Even with real guns an ammo change may help the gun operate better.

Why is the Trigger or Hammer Not Operating Properly?

I have come across blank guns where there are mechanical problems in the trigger and hammer areas, you may be able to address this yourself but I would recommend taking your blank gun to a gunsmith since you will have to take the gun pretty much full apart to fix a problem in the trigger and hammer areas.

Of course make sure your gun is clean and lubricated, this can help a lot with the mechanical areas of your blank gun.

One problem I saw with a few EKOL Special 99’s was specifically with the single action potion of the trigger, when I would pull the hammer back it would not lock back and the hammer would often slip and fire randomly, this is rather dangerous. When I took the gun apart I found that the table top or step that the trigger was supposed to catch on was worn down on the edge so it would simply slip off. I was able to fix this by filing a new edge on the step area. Again this can happen because blank guns are not made out of as high quality metal materials as real guns.

Why does the Flame Come out the Top of My Blank Gun and Not the Front?

If you find that the flame or discharge comes out of the top of your blank gun and not the barrel, this usually does not mean anything is wrong with your blank gun. All it means is you own a top venting blank gun and not a front firing blank gun. In some countries front firing blank guns are not allowed but front venting blank guns are. The same may also be reversed in some countries, for instance here in Canada we can only import front firing blank guns with flare adaptors since our blank guns are imported under the assumption that they are to be used as signaling or flare devices.

Can I Convert my Top Venting Blank Gun into a Front Venting Blank Gun?

I really don't recommend altering a blank gun in any way as it may be a violation of your local laws and it could cause the blank gun to malfunction in a very bad way causing serious injury or even death!

In theory I suppose it may be possible to convert your Top Venting Blank Gun into a Front Venting Blank Gun but again you would need to allow for just the right amount of back pressure so a wide open barrel would not work unless it was a revolver. You can not simply remove the red plug and bingo you have a front firing blank gun because in most cases the barrel will be completely plugged in the frontal region. Not only would you need to drill out the plugged portion of the barrel but you would also have to somehow fill in the top venting area and again makes sure to allow for just enough back pressure to cycle the slide back and forth.

Hopefully this has helped some of you with blank gun issues. If you’re looking for a blank gun make sure to come down to www.ReplicaAirguns.ca and www.ReplicaAirguns.us and have a look in our blank gun area of our online stores.

Categories: .22 cal, 380, 6mm, 8mm, 9mm, Blank Gun, How To, Pistol, Review, Revolver, Semi Auto, YouTube Video Tags:

Gletcher NGT NGT-R CO2 BB and Pellet Revolver Follow-up

No Comments

I already made several review videos for both Gletcher NGT (4.5mm Steel BB) and the Gletcher NGT R (.177 Cal Pellet) Revolvers, including table top and shooting videos. So make sure to check those videos out for more information on both versions of Gletcher NGT and NGT R Revolvers.

I did however miss some noteworthy details that I wanted to cover in this video. Firstly, the real steal Nagant M1895 Revolver this Gletcher NGT is styled after has a very unique gas-sealing system that the Airgun version does not replicate or really require but it is worth mentioning.

Here is some more info on how the original Nagant M1895 Revolver Gas Seal System works:

(From Wikipedia) The M1895 by contrast, has a mechanism which, as the hammer is cocked, first turns the cylinder and then moves it forward, closing the gap between the cylinder and the barrel. The cartridge, also unique, plays an important part in sealing the gun to the escape of propellant gases. The bullet is deeply seated, entirely within the cartridge case, and the case is slightly reduced in diameter at its mouth. The barrel features a short conical section at its rear; this accepts the mouth of the cartridge, completing the gas seal. By sealing the gap, the velocity of the bullet is increased by 15 to 45 m/s (50 to 150 ft/s.) This feature also eliminates the possibility of injury through the dangerous expansion of gases from the cylinder behind the barrel, which are easily capable of severing a finger if the user holds the gun incorrectly (with a finger positioned in front of the cylinder during fire) - a noted safety-issue in conventional revolvers.

Moving on to some of the features incorporated into the Gletcher NGT NGT-R CO2 BB and Pellet Revolver that I did not point in any of my previous videos. There is an extractor rod that can be used to extract a shell, this is not really necessary on the airgun version since the shells do not expand and tighten on the cylinder as they would n the real steal Nagant M1895 Revolver built is nice that we can replicate this feature with the Airgun version. You can also remove the cylinder completely from both the BB and Pellet shooting Gletcher NGT NGT-R CO2 Revolvers. The cylinder is actually very heavy and adds a lot of weight to this compact 7 shot Revolver.

It is always nice when an Airgun is built in such a way that it replicates the real steal version as closely as possible and the Gletcher NGT NGT-R CO2 BB and Pellet Revolvers do this nearly perfectly.

Categories: 4.5mm / .177 cal, BB, CO2, How To, Pellet, Pistol, Review, Revolver, YouTube Video Tags: Gletcher, NGT, NGT R

How to Get Rid of That Ugly White Writing on Your Airgun

1 Comment

I get asked on a daily bases form many of my Vimeo Viewers about how and if there is a way to get rid of the White lettering on Airguns, Typically people are wanting to remove the intrusive Warning instructions from Airguns like the Cybergun Tanfoglio Witness 1911, the Cybergun/Swiss Arms GSG 92/P92 and many other CO2 Replica Airguns that have lettering or branding that you may want to get rid of.

In this Instructional Tutorial Video I show you how can at least tone down the white lettering and even completely remove it on some Airguns without damaging the Airguns finish underneath the white lettering. You will have to use some patience and perhaps repeat this method a few times but the end result is worth the effort.

The magical product I use to remove the white lettering on many popular Airguns is a product from Birchwood Casey called the Presto Gun Blue Pen. This product is actually designed to touch up real steel gun in areas where the blueing has worn off, lucky for us the Birchwood Casey Presto Gun Blue Pen also works well to remove the ugly white lettering from Airguns.

Categories: 4.5mm / .177 cal, 6mm, Airsoft, BB, Blowback, CO2, How To, Pellet, Pistol, Review, Revolver, Semi Auto, YouTube Video Tags: Cybergun, KWC, Umarex

Which Shells Work in Which Shell Loading Revolvers?

No Comments

I have often been asked which of the Shells for the Shell Loading Revolvers work in which Shell Loading Revolvers? After all many of them look a lot alike so can you mix and match Shells for the various types of Shell Loading Revolvers?

In this Vimeo Instructional Video I test out a bunch of Shells to see which ones actually will work or not work in several of the most popular Shell Loading Revolvers.

Some of the Shell Loading Revovers Tested in this Instructional Video are:

Categories: 4.5mm / .177 cal, 6mm, Airsoft, BB, CO2, Comparison, How To, Pellet, Pistol, Review, Revolver, YouTube Video Tags: 357, ASG, Colt Single Action Army, Dan Wesson, Dan Wesson 715, G731, Gletcher, KWC, NGT, NGT R, Umarex, Webley

Can I put real 1911 Grips on my KWC-Cybergun 1911 BB-Airsoft Gun?

No Comments

With the popularity of the KWC - Cybergun 1911 Blowback CO2 Pistols and how super realistic they are in so many ways, it is no surprise that people often ask me if they can replace the original grips with grips made for a real 1911.

The short answer is yes you can! You will have to be prepared to remove just a little bit of material from the backside of both grips near the bottom of the handle where there is an area that has been flared out to accommodate the CO2. Not really a big deal, you can use a Dremel for the quick and easy approach or even some sand paper if you don't mind taking a little more time.

In this Vimeo Video I demonstrate using grips that fit a real 1911 and show you just exactly where you will need modify them to fit on the KWC and Cybergun CO2 Blowback 1911 pistol series.

Categories: 4.5mm / .177 cal, 6mm, Airsoft, BB, Blowback, CO2, Comparison, How To, Modification, Pistol, Real Gun, Semi Auto, YouTube Video Tags: Colt Government 1911, Cybergun, KWC, Model 1911, Tanfoglio Witness 1911

No Orange Tip On Your Airsoft Gun! Are You Insane?

No Comments

Whether you like it or not, most of us have come across an Airgun with an ugly orange tip on it at some point. In most cases you will find the intrusive orange or red tips on Airsoft guns that shoot plastic BB's, in some cases you will even find them on Airguns that shoot either lead pellets and/or steel BB's.

It really comes down to where you live as to what your local gun laws have determined is required for your area. You may even live in a region where Airguns and Airsoft guns are not allowed at all! So for you a red or orange tip on the front would be welcome if it would allow you to own an Airgun or Airsoft gun. What about the entire gun being painted a bright color, well that is the case for some folks so again having a red or orange tips may not be as bad as it originally seemed...

In Canada where I live, we used to only be allowed Airsoft guns that had clear sections as our replica gun laws are very strict and all black Airsoft guns would have fallen iinto the "replica" category if they did not have large clear plastic see-through sections on them. This clear section law was revised somewhat over the last several years to allow for all black Airsoft guns here in Canada. It was determined that many Airsoft guns with higher fps limits could cause a serious injury to a human, making them less of a toy in the eyes of the law and more of a weapon. Because of this, Airsoft guns that are capable of shooting a .20 gram plastic BB at a velocity of 360 fps or "higher" are now considered to be similar in the eyes of the law to a regular steel BB or lead pellet shooting Airgun. In Canada, Pellet and Steel BB guns are actually considered firearms of a sort so this allows the higher fps Airsoft guns to be all black since it can not be a replica of a firearm if it is in fact considered to be a firearm by law.

The long and short of all of this is that here in Canada we do not require our Airsoft guns to have orange or red tips since they are considered more or less to be just like any other Airgun and our Airguns do not have red or orange tips either.

Getting back to the title of this article "No Orange Tip On Your Airsoft Gun! Are You Insane?" I often get folks from the US giving me heck for removing the orange tips from my Airsoft guns or asking me why my Airsoft guns don't have them in the first place. These people even state that I could get in a lot of trouble for this! Perhaps they think I live in the US or that US laws govern Canada as well? I am not sure but I can say for the record that I am not breaking any laws at least here in Canada where I live.

I know in the US that wholesalers and retailers by law have to sell Airsoft guns with the affixed orange tips on them, once the end user receives that gun and depending on which state they live in, it may or may not be legal to remove the orange tip. Again, you will need to look into your local state laws as they are different from state to state in the US.

Categories: 4.5mm / .177 cal, 6mm, Airsoft, BB, Blank Gun, Comparison, Gun Law, How To, Pellet, Pistol, Q&A Video, Revolver, Rifle, YouTube Video Tags:

Best BB Guns

1 Comment

First off let’s get one thing straight! What I’m looking for in a BB gun is more than likely going to be way different than what someone else is looking for in what they think is the “Best BB Gun” available.

Many people will determine the Best BB Gun as the BB gun that has the highest price tag, usually you get better quality the higher the price goes up but not always, there are times when perhaps you are paying for a name brand or cosmetic add ons that don’t always make the gun better or the best.

On the other hand, some people will determine the best BB gun as the one that is the least cost since they may not have a lot of money to spend, and an expensive BB gun is a BB gun that that person would not be able to afford or even own, far from an ideal or the Best BB Gun for them.

Many people only look at the specifications to determine if that particular BB gun is the outright best BB Gun. One specification that people seem to fixate on is how powerful is the BB gun in question? If it has the highest FPS then surely it must be the best BB Gun! That Pop can never saw it coming! What about cost of operation, so things like reliability and how many shots per CO2 you can get out of a BB gun. All important features to consider when picking out the Best BB Gun!

Style is another important part of what makes a BB Gun the Best option for you, are you wanting a classic BB Pistol? Perhaps a Modern BB Gun, Maybe even a BB gun that you can not get in your area because of gun laws? Style is a very individual preference and what looks good to me may look terrible to someone else.

One aspect that is very important to me, is realism, does the BB Gun operate the same and does it have similar metal and plastic parts as the real steel version? Does the BB gun I am considering have blowback operation and a true single or double action trigger like it’s big brother? What about a full size drop out magazine and the ability to field strip the BB Gun?

Some people want their BB gun for simple backyard good old fun shooting and so as long as it shoots pretty straight and works as it’s supposed to, then that is all they care about. Many real steel shooters want a BB Gun to operate exactly like their real steel version, so they can practice with it to get in more trigger time when going to a gun range is not an option.

Of course there are aspects like Reliability, Performance, Fit and Finish, Licensing and Build Quality that all determine what makes the Best BB Gun and again it really depends which of these qualities are most important to you that will determine which BB Gun is the best BB Gun.

So how do you determine which is the Best BB Gun? Make a list of what you are looking for in a BB Gun. Attributes like Cost, Performance, Build Quality, Style, Realism, Availability…

Once you have narrowed down your Best BB Gun list, get as much information on each BB Gun you are considering, to narrow the list down even more. There are tons of Youtube videos you can watch for your Best BB Gun final short list to help you determine your ultimate choice.

So please don’t ask me what the Best BB Gun is? I can not even tell you which one I like the best since my wish list changes from day to day…

Categories: 4.5mm / .177 cal, 6mm, Airsoft, BB, Blowback, CO2, Comparison, Full Auto, GBB, Gas, Pellet, Pistol, Q&A Video, Repeater, Revolver, Semi Auto, YouTube Video Tags:

Clay Pigeons as Reactive Targets for Airguns and Airsoft Guns

2 Comments

If you have been watching my Full Auto Fun Videos, then you will have noticed that I have recently been using Clay Pigeons as my go-to targets. Generally Clay Pigeons are shot from launchers and used with shotguns since the flight of the Clay Pigeon simulates a bird in flight nicely.

So I thought, why not use them as reactive targets for my Airguns and Airsoft guns? It turns out they work pretty darn good, well at least with 4.5mm Steel BB pistols and I would imagine even better with pellet guns. What about Airsoft guns, will the Airsoft lighter weight plastic BB's have enough mass to get the job done?

You'll have to watch this video to find out the answer to that question when I unload a full magazine of .20 gram Airsoft BB's into some Clay Pigeons using my KWC .50 Desert Eagle...

 
Categories: Field Test, How To, Review, YouTube Video Tags: Desert Eagle, KWC

Replica Airguns Q&A Questions and Answers #2

3 Comments

Some more answers to some of your commonly asked questions. In this second Q&A Questions and Answers YouTube video I discuss some more of your questions, specifically:

  • What's going on with my order?

  • Do I need to clean and oil my airgun?

  • What is the most powerful blowback BB gun? 

  • I don't live in Canada or the US, do you ship to other countries?

So make sure to watch my second installment for the Replica Airguns Viewer Q&A Questions and Answers.

Categories: Q&A Video, YouTube Video Tags:

Replica Airguns Q&A Questions and Answers #1

1 Comment

Here we go with the first installment of the Replica Airguns Q&A Questions and Answers! Below are some of the questions I answer for some of my YouTube subscribers and followers.

1969triumph:

I find your vids very informative. One Quick question. All of the pistols I have are all close copies of real guns :- PPK ,1911 etc. What I would really like now is a western 6 shooter. Are there any in the pipeline ? Thanks Paul.

Kevin Men:

Will you be selling the Kalashnikov AK47 co2 bb gun? I heard it was made of real AK 47 parts and it might be banned in the US! Do you think the gun will be for sale ever again?

WindandWood:

When is the KWC Luger P-08 4.5 BB version going to be for sale in your USA store? Thanks!

Knight Rider:

Hey i found on a store two types of CO2 cartridge for a bb gun and i want to know if I can use bought in the same gun? One CO2 cartridge has lubrication in it and the another one is just a normal cartridge?

LOLfailblogger:

Will you get the pellet version of the Dan Wesson revolver available for purchase in the Canadian store?

ELinktricTears:

When are you going to make a how to get buff channel?

I also talk about generic gun repair questions.

Categories: Q&A Video, YouTube Video Tags:

How to Fix Leaking CO2 in an Airgun?

8 Comments

A very common occurrence with CO2 Airguns and Airsoft guns are leaky CO2 seals. Usually this occurs right where the CO2 cartridge connects to the main valve area. This can be either in the gun or in the magazine depending on the setup of the airgun.

There are many reasons why this can happen, but the most common reasons are a worn-out or dried up seals or even a seal that has been imprinted or misshapen from the constant pressure of the tip of the CO2 pressing against it.

When this happens you may encounter a leaking CO2, the severity of the leak can vary from mild slow leaks to leaks that can be so bad that the gun is unusable. Keep in mind there can be other problems not related to the CO2 seal such as in the valve area, the fix I show you in this YouTube video will not fix a leaking valve, you can try using something like Crosman Pellgun oil for a problem like that.

Watch my below Vimeo video where I show you how you can easily use some Plumbers Teflon Tape to improve the contact points between your CO2 and CO2 main seal and eliminate leaking CO2 in your Airgun.

Categories: CO2, How To, YouTube Video Tags:

How Long Can I Leave CO2 in My Airgun?

1 Comment

A very common question I get asked is "How Long Can I Leave CO2 in My Airgun?" So what do I do when I get asked a question over and over again... Well I make a video and give you my answer to the question.

Some CO2 Related Questions I seem to get over and over again are:

  1. Can I leave an unused CO2 in my Airgun and for how long is it safe?

  2. Can I reuse a C2 once it is empty?

  3. Can I use my gun without CO2?

In this YouTube video I address questions 1 and 2, I kind of forgot about question number 3 since it is not as often but it does come up from time to time believe it or not and the answer to being able to use a CO2 airgunwith out CO2 is "NO", It's kind of like trying to drive a car without gas, or turn on a light without electricity or stay alive without food...

So anyways, watch my below Vimeo video for answers to questions one and two:

Categories: CO2, How To, YouTube Video Tags: