I have already reviewed several Crosman 357 Pellet/BB Revolvers in the past like the Crosman Vigilante which also has the ability to shoot both .177 caliber pellets and 4.5mm Steel BB’s, (Really they all are with the right magazine). With the Vigilante my pellet chronograph tests got similar results but with Steel BB’s the Crosman Vigilante did a lot better than my Crosman Triple Threat CO2 Dual Ammo Revolver using a similar 6 inch barrel. As expected both the Crosman Vigilante and the Crosman Triple Threat did about the same in terms of accuracy getting better results with pellets over Steel BB’s.
Starting with the velocity portion of my Indoor Field Test Shooting video, I placed a brand new 12 gram CO2 into the Crosman Triple Threat CO2 Dual Ammo Revolver and tested out some 7 grain .177 caliber Lead Pellets. I averaged 382 fps in what I would consider normal indoor temperature ranges so you can expect a bit higher velocities in warmer conditions. Moving on to 4.5mm 5.1 grain Steel BB’s, I averaged quite a bit lower velocity at 288 fps. I was surprise since it was almost 100 fps lower than the heavier 7 grain lead pellets. The logical reason for this is that lead Pellets fit the barrel much more snug, stoping any CO2 from getting around them which helps increase the velocity over Steel BB’s which are a hard metal and need to be slightly smaller in diameter and therefore do let some CO2 get by reducing the pressure behind them.
For the accuracy porting of the the Indoor Field Test I shot 10 rounds for my pellet magazine first and then 6 rounds for the BB magazine, simply because this is how many rounds each magazine holds… Makes sense right? Even with the pellet magazine holding 10 rounds over the BB magazine’s 6 rounds, the Pellet magazine was still able to get a much tighter grouping at around 1 inch over the BB target which was closer to 3 inches. BB’s seemed to really like to hook a bit with the Crosman Triple Threat CO2 Dual Ammo Revolver, so I would for sure go with pellets if accuracy is importatn to you. Both pellets and BB’s shot a little bit high and to the left from the bulls-eye but that can easily be adjusted with the fully adjustable rear sight.
The Crosman Triple Threat performed rather as expected and was not a big surprise other than the BB’s really having a much lower velocity this time around. It is clear to me that I would not waste my time shooting Steel BB’s unless this is all I had on hand as they where not only much slower but also a lot less accurate. Over time the steel BB’s could damage the rifled steel barrel effecting future pellet accuracy. The Crosman Triple Threat CO2 Dual Ammo Revolver offers a lot of options with ammo choice and barrel choice that alter it’s looks and even performance to some degree but if you want a Crosman 357 type CO2 Revolver than it for sure gives you the most flexibility.
On with the show… First I shot five rounds through my Chronograph using a brand new CO2 in what I would consider to be room temperaterer (20C or 70F). Sig Sauer claims their MCX Rattler shoots around 325 fps and in my testing I got a five shot average of 318 with my slowest shot hitting 298 and my fastest shot hitting 346. So I would say Sig is right on the mark here.
I then setup a fresh pepper target 30 feet away and loaded up a full magazine (30 rounds) for my accuracy test where I first shot in 10 rounds in semi auto and then the remaining 20 rounds in three round burst. I would say I was able to get around a 2 inch grouping in semi auto but I did have to shoot aiming on the bottom of the rings and I was using the flattened sights rather than the pop up sights as you have two options with the Sig Sauer MCX Rattler CO2 BB Rifle. Once I switched the selector to three round burst, my grouping really did not change all that much, maybe 3 inches at most and that was with 20 rounds.
The Sig Sauer MCX Rattler CO2 BB Rifle is a lot of fun, it is by far not the most powerful blowback full auto-ish Blowback BB Rifle out there but it performs decent and looks really good. The internal blowback action does give you a slight tapping feel and it does allow for a true single action trigger. If you want a rather compact Blowback BB Rifle with Sig licensing and branding along with Sig quality then take a look at the Sig Sauer MCX Rattler CO2 BB Rifle. Did I mention it was really affordable too?
Type: Non-blowback CO2 BB Pistol. Manufacturer: Distributed by Bear River. Model: Bear River BR45. Materials: Mostly plastic. Weight: 1 pounds (454 grams). TotalLength: 8 inches (203mm). Barrel: 4.72 inches (120mm) metal non-rifled. Propulsion: CO2 x 1. Action: Semi auto non-blowback, DOA trigger. AmmunitionType: .4.5mm steel BB’s. AmmunitionCapacity: 20 round drop out metal stick magazine. FPS: Claimed 410.
Trigger Pull: The Bear River BR45 NBB CO2 BB Pistol has a double action trigger commonly found on lower cost NBB CO2 BB Pistols with a long trigger pull that requires more length and effort to pull, but I would say is still usable for action shooting. Your finger will get worked a bit after several magazines of action shooting. The Bear River BR45 trigger pull makes the internal metal barrel move forward and out of the front of the barrel opening but as it has a recessed barrel you don’t really see it protruding out of the front. When you reach the release point the barrel snaps back into the BB Pistol acting like the hammer and releasing CO2 and shooting a BB.
Accuracy: I have not shoot the Bear River BR45 NBB CO2 BB Pistol yet or performed my standard Field Test Shooting Video, so I can not comment at this time on the actual performance other than what is claimed in terms of fps (410fps). I have shot several similar CO2 BB Pistols which share almost the exact same internal components but have a different external skin on them. One bonus is that all this style of metal stick magazines are the same so they will be interchangeable. My previous experiences with similar BB Pistols is that they will get mid 400fps velocities and in general will shot around a 2 inch grouping or so. It is hard to say how close the Bear River BR45 is going to shoot to the bullseye, as out of the box it may shoot a bit high or low or left or right. We will find out during my shooting test.
Build Quality: The Bear River BR45 NBB CO2 BB Pistol is an almost all plastic moulded Airgun with only a few metal parts I can pick out. The trigger and magazine are metal along with the inner barrel and the area where the CO2 goes in. Because of the plastic build, it is rather light weight at around 1 pound which can actually be good if you were to drop it on a hard surface as the mass is low resulting in less damage. Scratches will also be less noticeable on an all plastic exterior Airgun over a metal Airgun as the material on a plastic Airgun is going to have the color throughout the material rather than a painted surface that will show blemishes a lot more. The simplicity of the design means you should get a lot of use from the Bear River BR45 before encountering any issues.
Realism: The Bear River BR45 NBB CO2 BB Pistol is not a replica of an exact real steel gun in production but it does take after a Sig Sauer or H&K looking at the basic shape and features. There are few external mechanical working parts on the Bear River BR45 other than the trigger, safety, magazine and inner barrel. The barrel is well recessed and the CO2 tab is sunken in the grip which helps in terms of it looking more realistic.
Pros:
Nice size BB pistol, feels good in the hand.
Decent FPS rating of 410.
Picatinny rail on frame for adding on accessories.
Non-blowback should get lots of shots per CO2.
Easy to see white dot sights front and back.
CO2 tab is recessed and somewhat hidden under the grip.
Double action trigger pull is long but not too firm.
Uses a generic all metal stick magazines commonly found in lower cost BB pistols.
Recessed barrel looks that part.
Simple design with not a lot of moving parts will make it reliable for a long time.
Cons:
All plastic gun for the most part.
Not many working parts, pretty much all moulded gun.
CO2 tab a bit hard to use for people with bigger fingers.
Comments:
The Bear River BR45 NBB CO2 BB Pistol is a basic mostly all plastic NBB CO2 BB Pistol very simple in design which makes it dependable and reliable as there is a lot less to go wrong as compared to a blowback metal BB Pistol with lots of moving parts. Also keep in mind the metal in Airguns is not as hard or strong as you find in a Real Steel Pistol so all of these moving metal parts will wear over time and some may eventually fail. Other advantages of a NBB CO2 BB Pistol are that it will have a decent velocity rating and it will also get more shots per CO2 as compared to blowback Air Pistols, so not only is the initial cost of a simple NBB Air Pistol going to be less but also you will not need as much CO2 to operate it. I do like the size of the Bear River BR45 NBB CO2 BB Pistol as it is a bit larger than similar NBB Replica Air Pistols which for me and my larger hands is a good thing.
Type: Non-blowback CO2 BB Pistol. Manufacturer: Distributed by Barra. Model: Barra 380. Materials: Mostly plastic. Weight: .93 pounds (422 grams). TotalLength: 6.89inches (175mm). Barrel: 4.25 inches (108mm) metal non-rifled. Propulsion: CO2 x 1. Action: Semi auto non-blowback, DOA trigger. AmmunitionType: .4.5mm steel BB’s. AmmunitionCapacity: 20 round drop out metal stick magazine. FPS: Claimed 410.
TriggerPull: The Barra 380 NBB CO2 BB Pistol has a typical double action trigger with a longer trigger pull that requires more length and effort to pull, but I would say is still usable as an action shooter. Your finger will get a bit tired after several magazines of action shooting. The Barra 380 trigger pull makes the internal metal barrel move forward and out of the front of the barrel opening enough to see it clearly, then when you reach the release point it snaps back into the BB Pistol acting like the hammer and releasing CO2 and shooting a BB.
Accuracy: I have yet to shoot the Barra 380 NBB CO2 BB Pistol or even performed my standard Field Test Shooting Video as of yet, so I can not comment at this time on the actual performance other than what is claimed in terms of fps - 410fps by the way. I have shot several similar CO2 BB Pistols which share almost the exact same internal components but have a different external skin on them. One benefit is that all this style of metal stick magazines are the same so they will be interchangeable. My previous experiences with similar BB Pistols is that they will get mid 400fps velocities and in general will shot around a 2 inch grouping or so. It is hard to say how close theBarra 380 NBB CO2 BB Pistol is going to shoot to the bullseye, as out of the box it may shoot a bit high or low or left or right. We will find out during my shooting test.
BuildQuality: The Barra 380 NBB CO2 BB Pistol is a pretty much almost all plastic Airgun with only a few metal parts I can see on it. The trigger is metal along with the inner barrel and the area where the CO2 goes in. Because of the plastic build, it is rather light weight which can actually be good if you where to drop it on a hard surface as the mass is low resulting in less damage. Scratches will also be less noticeable on a plastic Airgun over a metal Airgun as the material on a plastic Airgun is all tan/black throughout the material rather than a painted surface that will show blemishes a lot more. The simplicity of the design means you should get a lot of use from the Barra 380 before encountering any issues.
Realism: The Barra 380 NBB CO2 BB Pistol is not a replica of an exact real steel gun in production but it does take after a compact Beretta when you look at the open barrel and similar trigger guard. There are few external mechanical working parts on the Barra 380 CO2 NBB BB Pistol other than the trigger, safety, magazine and inner barrel. The barrel is slightly recessed and the CO2 tab is hidden in the grip which helps in terms of it looking the part.
Pros:
Nice compact size BB pistol easy to transport.
Decent FPS rating of 410.
Should get lots of shots per CO2 as it is non-blowback
Picatinny rail on frame for adding accessories.
Does have a white dot sight up front.
Finger groves on pistol grips for a secure grip.
CO2 tab is well hidden within the grip.
Double action trigger pull is long but not too firm.
Uses a generic all metal stick magazines commonly found on lower cost BB pistols.
Simple design with not a lot of moving parts will make it reliable for a long time.
Cons:
All plastic gun for the most part.
Not many working parts, pretty much all moulded gun.
Grip can pop of kind of easy if you pull a bit hard.
Sights are non adjustable and no white dots on the rear sight.
Comments:
I often mention how I prefer blowback Airguns that have a more solid weight and feel to them with more working parts, but again there is a lot more that can go wrong and complex parts wear out over usage a lot quicker than a more simple design as in the the case of the Barra 380 NBB CO2 BB Pistol. Price is also going to be a lot less when looking a more simplified Air Pistol like the Barra 380, as the plastic build is a lot cheaper to produce over more expensive metals. Another bonus with non-blowback CO2 airguns is that they do tend to have a higher velocity with more shots per CO2 than a similar CO2 Blowback Pistol, so less expensive to shoot over time. It really depends what you are really looking for? A couple other strong points to mention about the Barra 380 NBB CO2 BB Pistol would be the compatibility with other similar styled CO2 BB pistol metal stick magazines and if you like the look of a Beretta then you may also like the look of the Barra 380.
Type: Non-blowback CO2 BB Pistol. Manufacturer: Distributed by Crosman. Model: MK45. Materials: Mostly plastic. Weight: .63 pounds (281 grams). Total Length: 7.25 inches (184mm). Barrel: 4.5 inches (114mm) metal non-rifled. Propulsion: CO2 x 1. Action: Semi auto non-blowback, DOA trigger. AmmunitionType: .4.5mm steel BB’s. AmmunitionCapacity: 20 round drop out metal stick magazine. FPS: Claimed 480.
Trigger Pull: The Crosman MK45 CO2 NBB BB Pistol has a typical double action tiger with a longer trigger pull that requires more length and effort to pull, but I would say is still usable as an action shooter. The Crosman MK45 trigger pull makes the internal metal barrel move forward and out of the front of the barrel opening a bit, then when you reach the release point it snaps back into the BB Pistol acting like the hammer and releasing CO2.
Accuracy: I have yet to shoot the Crosman MK45 CO2 NBB BB Pistol or performed my standard Field Test Shooting Video, so I can not comment at this time on the actual performance other than what is claimed in terms of fps. I have shot several similar CO2 BB Pistols which share almost the exact same internal components but have a different external skin on them. The good news is the metal stick magazines for all of these type NBB CO2 BB Pistols are the same so they will be interchangeable. My previous experiences with similar BB Pistols is that they will get mid 400fps velocities and in general will shot around a 2 inch grouping or so. It is hard to say how close the Crosman MK45 CO2 NBB BB Pistol is going to shoot to the bullseye, as out of the box it may shoot a bit high or low or left or right. We will find out during my shooting test.
Build Quality: The Crosman MK45 CO2 NBB BB Pistol is a pretty much an all plastic Airgun with only a few metal parts I can find on it. The trigger is metal along with the inner barrel and the area where the CO2 goes in. Because of the plastic build, it is rather light weight which can actually be good in a fall as the mass is low resulting in less damage if you were to drop it on a hard surface. Scratches will also be less noticeable on a plastic Airgun over a metal Airgun as the material on a plastic Airgun is all tan/black rather than a painted surface that will show blemishes a lot more. The simplicity of the design means you should get a lot of use from the Crosman MK45 CO2 NBB BB Pistol before encountering any issues.
Realism: The Crosman MK45 CO2 NBB BB Pistol is not a replica of an exact real steel gun in production but it does share a lot of cosmetic characteristics as what you would see on a Sig Sauer or even H&K Pistol. The magazine release on the Crosman MK45 looks and works a lot like what you will find on an H&K Pistol. There are few external mechanical working parts on the Crosman MK45 CO2 NBB BB Pistol other than the trigger, safety and inner barrel. The barrel is slightly recessed and the CO2 tab is hidden in the grip which helps in terms of believability.
Pros:
Desert tan with black grips looks really good in my opinion.
High FPS rating of 480.
Picatinny rail on frame for adding on accessories.
Non-blowback should get lots of shots per CO2.
Easy to see fiber optic sights front and back.
CO2 tab is nicely hidden inside the grip.
Double action trigger pull is long but not too firm.
Uses a generic all metal stick magazines commonly found on lower cost BB pistols.
Ambidextrous magazine release.
Simple design with not a lot of moving parts will make it reliable for a long time.
Cons:
All moulded plastic BB gun for the most part.
Not many working parts, it’s pretty much an all plastic BB gun.
Grips are fairly loose, they don't really snap into place.
Sights are not adjustable.
Comments:
I personally prefer blowback Airguns that have a more solid weight and feel to them with more working parts, but again there is a lot more that can go wrong and parts tend to complex parts wear out over usage a lot quicker than a more simple design like in the case of the Crosman MK45 CO2 NBB BB Pistol. Price is also going to be a lot less when looking a more simplified Air Pistol like the Crosman MK45, as the plastic build is a lot cheaper to produce. Another bonus with non-blowback CO2 airguns is that they do tend to have a much higher velocity and also generally you will also get more shots per CO2 than a similar CO2 Blowback Pistol. It really depends what features you want more and in this case you also get a more cost effective Air Pistol with plenty of shooting enjoyment. A couple other strong points to mention about the Crosman MK45 CO2 NBB BB Pistol would be the fiber optic sights front and back and its sharp l looking two tone layout.
Trigger Pull: The trigger pull on the Crosman Triple Threat CO2 Dual Ammo Revolver like pretty much all of the 357 type Crosman Revolvers is rather nice in single action with virtually zero take-up and it has a not too light weight with a predictable feel to it. In double action it does get much longer and heavier but still very usable. If you have larger thicker finger then you may want to start off in single action as the finger opening is a bit tight.
Accuracy: I have not specifically tested out the Crosman Triple Threat so far but I would be very surprised if it was any different than the standard Crosman 357 and the Crosman Vigilante I have already done Field Test Reviews for. Other than the shape of the outer barrel, both of these guns are virtually the same including the frame and the 6 inch barrels. Back in 2012 when I tested out the Crosman 357 I averaged around 400 fps using mid grain lead pellets and was able to get a 1 to 1.5 inch multi-shot grouping at 30 feet away from my paper target. I will be making an update Field Test Shooting Video so we will see if I can replicate these results with the standard Crosman 357 and Vigilante CO2 Pellet and BB Revolver.
Build Quality: The CCrosman Triple Threat CO2 Dual Ammo Revolver is a fairly basic pistol that incorporates a variety of length plastic outer barrels and inner steel barrels (3/6/8 inches), the grips are also plastic as expected and so are the magazines and sights. Most everything else is metal including the receiver, trigger and hammer. This line of Crosman 357 pistols has been around for decades so you can expect hours of fun and reliable shooting with their multi-barrel dual ammo version.
Realism: There are for sure a lot more realistic looking Replica Revolvers out there with swing out cylinders that eject the shells just like their real steel counterparts, but where the Crosman Triple Threat shines is in performance, reliability and consistency. You will get more shots per CO2, higher fps and better accuracy with the Crosman Triple Threat CO2 Pellet and BB Revolver over other more realistic Revolvers on the market.
Pros:
Inexpensive Pellet revolver with a proven track record that goes back decades.
Good usage of metal parts where you need them most. (Metal trigger, hammer, frame, barrel, CO2 Tab screw
Single and double action trigger for action and more focused shooting.
Excellent accuracy and good power with a reasonable amount of shots per CO2 (based on similar versions).
Fully adjustable rear sight.
Riffled steel barrels (All three of them).
3 different barrel choices (3/6/8 inches) depending on the look and how compact you want it to be.
CO2 and tab are nicely hidden and use all metal.
Come with both a Pellet and BB magazines..
Cons:
Outer barrels are plastic but very solid. Metal would have added a bit more weigth perhaps better balance?
Grips and trigger pull length may be a bit long for smaller handed people when shooting in double action.
Not your most real revolver out there in terms of replicas out there but probably more usable then most.
No white dots on the sights.
Comments: The Crosman Triple Threat CO2 Dual Ammo Revolver is basically another reskinned Crosman 357 at the end of the day with a ton of options including 3 different barrel lengths that will change the look, size and power depending on your needs. You also have the choice of what ammo you want to use, cheaper 4.5mm Steel BB’s or more accurate and even higher velocity lead pellets for greater downrange energy and precision. If you are not sure which Crosman 357 type revolver to get? The standard 357… the Vigilante or the Triple Threat, maybe go with the Triple Threat at the end of today as it offers the most options and variety of configurations.
Type: BB Rifle. Manufacturer: Sig Sauer ASP Model: Sig Sauer MCX Rattler Materials: Metal and Nylon Fiber build. Weight: 4.6 Pounds (2.1 kg). Barrel: 7 inch (17.8 cm) steel non-rifled. Propulsion: Single 12 gram CO2. Action: Semi auto and 3 round burst with internal blowback (single action only trigger). AmmunitionType: 4.5mm Steel BB’s. AmmunitionCapacity: 30 rounds spring fed. Velocity: Claimed of 325 fps.
TriggerPull: The trigger pull on the Sig Sauer MCX Rattler CO2 BB Rifle is a single action only trigger that requires initial activation of the charging handle, after the first shot the internal blowback action will do this automatically for each followup shot. The single action only trigger is fairly short with a light pull and predictable release, great for action shooting. You also have the option of shooting in true semi auto (one trigger pull and one shot) or selecting 3 round burst mode which allows for one pull of the trigger with 3 rounds in full auto.
Accuracy: I really don’t have much feedback to give here as I have only shot a single magazine so far with the Sig Sauer MCX Rattler CO2 BB Rifle in a very uncontrolled format as I was not so much testing it out but rather just having some initial fun to see what it was all about. I will of course be following up this Table Top Review with a Field Test Review shortly to find out what the actual velocity is and see how accurate it is in both semi auto and 3 round burst mode.
BuildQuality: The build quality for the Sig Sauer MCX Rattler CO2 BB Rifle is really good considering it is mostly all plastic on the outside. It does feel solid and well built when holding it in the hand. From what I can tell the metal parts would include the barrel, the charging handle, the main controls and also much of the internal components inside both the rifle and the magazine. I would have liked to have seen a metal flash hider and perhaps the pop-up Iron sights could have also been metal.
Realism: The Sig Sauer MCX Rattler CO2 BB Rifle is a 1 to 1 scale very realistic Replica of the real steel Sig Sauer Rattler normally chambered in 5.56 NATO. It would have been nice if the dust cover opened up when charging the Airgun for realism but most of the other controls work as expected, like the charging handle, selector switch, magazine release and I am not sure but maybe even the bolt release, I will know more when I make my Field Test Shooting video for the Sig Sauer MCX Rattler.
Pros:
Perfect size and weight for a fun BB semi / full auto shooter.
Fully adjustable pop up sights that are usable in both the down and up position,
Lots of accessory mounting options with the picatinny top rail and MLOCK in the sides and bottom.
Folding rear stock allows for a compact size and much easier transportation.
Ambidextrous selector switch.
Can shoot in both semi and 3 round burst modes.
Very solid AR15 type magazine that holds the 30 4.5mm steel BB’s and the single 12 gram CO2.
Reasonably priced at around $250 at the time of this video.
Sig Sauer licensing.
Cons:
Only uses a single CO2, two would have been better in a fast action shooter like this to maintain fps.
325 fps seems a bit low.
Lots of plastic but build quality does feel good.
Comments:
The Sig Sig Sauer MCX Rattler CO2 BB Rifle reminds me a lot of the Umarex Steel Storm and Steel Force which are both Compact AR type Semi and Burt mode 4.5mm CO2 Blowback Airguns. Where the Sig Sauer MCX Rattler CO2 BB Rifle shines, is in the quality and realism as compared the Umarex counterparts. I do like that both the Umarex Steel Storm and Steel Force use dual 12 gram CO2 cartridges which I feel allows them to have more consistent velocity and performance as compared to the single CO2 in the Sig Sauer MCX Rattler CO2 BB Rifle. My First impressions without really testing the Sig Sauer MCX Rattler are all pretty positive but it will really come down to how well it performs and so I will put my recommendations on hold until I actually test it out!
My Table Top Review of the Sig Sauer MCX Rattler CO2 BB Rifle:
I love making these Mystery Box Unboxing Videos as many of the items inside are actually real mysteries to me, some I may have an idea of but even these items are new to me so it’s fun to open them up and check them all out. In this October 2023 Mystery Box Video I checkout 9 items ranging from AEG Airsoft Rifles to Airsoft , BB and Pellet Pistols. There is even a new Steel BB product from Sig Sauer that is a compact rifle with a 3 round burst option when shooting.
30 feet is not really a long enough distance to test out a Spring Piston Break Barrel Air Rifle but it’s been pretty rainy outside as the weather here in British Columbia has progresses into full on rainy fall weather. So we will have to make do with the 30 foot limitation I have here in the Replica Airguns Sea Can Indoor Shooting Range. At least it is warm and the lighting is perfect :) In this Filed Test Shooting Video for the Beeman Black Panther Dual Caliber Break Barrel Pellet Rifle I test out the velocity in fps along with the accuracy at 30 feet away. For both of these tests I use 15.43 grain .22 caliber Gamo lead pellets. If you are more invested in details and specifications along with some closer up video then watch my Table Top Video for the Beeman Black Panther.
Beeman claims just under 500 fps for the Beeman Black Panther Dual Caliber Break Barrel Pellet Rifle but it is unclear if this is with .177 caliber or .22 caliber pellets and what kind of pellet are being used? Light weigth Alloy or standard Lead pellets. I decided to go with the .22 caliber barrel for all my testing but may try out the .177 caliber barrel in a future update Field Test Video. I placed 5 shots through my Chronograph using the 15.43 grain .22 caliber lead pellets and was able to get an average velocity of 422 fps. The slowest shot was 418 fps with the fastest shot hitting a max of 429 fps so all fairly close together. In terms of energy output, a pellet that weighs 15.43 grain travelling at 422 fps has a foot pound energy of 6.1.
I am not the best shot when it comes to sprig Piston Air Rifles, but I did my best here. I shot a total of 8 shots on the paper target and the main group was about 1 inch in diameter, this consisted of 6 pellets in that main group with 2 pellets that came out one shot a bit high and one shot a bit to the right. I was using the built in post and notch fiber optic sights rather than installing the 4x32 scope. After all the target was only 30 feet away. I am pretty sure one could easily get a .5 inch grouping at this range with perhaps a 1 inch grouping at distances closer to the 50-60 foot mark, which should make this a decent pest control option when using the .22 caliber ammo as I feel it would get the job done with a bit more authority.
The Beeman Black Panther Dual Caliber Break Barrel Pellet Rifle comes with two barres offering the ability to shoot using .177 caliber pellets or .22 caliber pellets with a quick barrel change. .177 caliber pellets could be used for smaller pest control but I would mainly use the .177 barrel for basic target practice as .177 caliber pellets are definitely cheaper than .22 caliber pellets. When you do require that slight additional stopping power, then go with the .22 caliber barrel for sure!
I don’t get to test out Bolt Action Airsoft Sniper type Rifles all that often but I do enjoy them for sure. I would like to test out the S&T Matrix KAR98K Bolt Action Airsoft Rifle using longer ranges than I can here in the Replica Airguns Indoor Sea Can Shooting Range but hopefully this Filed Test Review gives you an idea of what this Spring powered Bolt Action Airsoft Rifle can do. Make sure to watch my Table Top Review for the S&T Matrix KAR98K Bolt Action Airsoft Rifle for details, specifications and closer up video. In this video I mainly test out the velocity and accuracy at 30 feet away to see what the actual fps is and how tight of a 10 shot grouping I can get on a paper target.
Starting with the velocity test, I generally put 5 rounds through my Chronograph and then average them out for a real world rating. In this test I used standard .20 gram Airsoft BB’s for both the velocity and accuracy components of the video. I was very impressed with the consistency of the velocity with the slowest shot hitting 362 fps and the fastest shot hitting 363 fps averaging 362.5 fps and only having a 1 fps maximum difference between all shots. Pretty good right? Consistent velocity is very important for any sniper type rifle as if there is a large spread in velocity this can reduce elevation accuracy down range.
In terms of accuracy I was again very impressed with my results. For my target test I setup a fresh paper target 30 feet away and proceeded to shoot 10 rounds into it. I did have to reset for each shot as I had to manually work the bolt after each shot, this can affect accuracy but it did not seem to all that much. I was using a seated position in the back with my hands rested on a sand bag up front which does hep settle things down. Even with having to reset between each shot, I still managed to get close to a 1 inch 10 shot grouping, one shot did shoot just a bit high but that was probably me pulling it a bit. Out of the box with no sight adjustments the S&T Matrix KAR98K Bolt Action Airsoft Rifle shot almost dead center in the bullseye, it is fairly easy to adjust the elevation using the rear sight but there is no easy way to adjust for windage using the built in iron sights.
I know this is a Field Test Shooting Video and so it’s not really all about build or quality. That said I do love the quality and attention to detail the S&T Matrix KAR98K Bolt Action Airsoft Rifle has and the fact that it performs really well too is a big bonus. One last point I did not even mention in the Field Test Video is that Was able to load a lot more than 11 rounds into the magazine. I stoped at 19 as the spring was getting on the tight side, but may have been able to load more? If you’re looking for a sniper rifle with a history and that will stand out in a game then take a look at the S&T Matrix KAR98K Bolt Action Airsoft Rifle as an option.
In this Field Test Shooting Review Video I test out the Bear River Black Ops SR4 CQ AEG Airsoft Rifle (which I would consider to be a midrange AEG Airsoft Rifle) to see how it performs in the Replica Airguns Sea Can Indoor Shooting Range. As always this test is to see what the real world velocity is using .20 gram Airsoft BB’s and I also shoot 10 rounds in semi auto and then essentially a mag dump in full auto to see what kind of accuracy I can get from 30 feet away shooting in both shooting modes. If you want more info on details and specifications along with some closer up video of the Bear River Black Ops SR4 CQ AEG Airsoft Rifle then watch my Table Top Video Review here.
Starting with the velocity or fps portion of my review, my 5 shot average produced 320 fps that was very consistent shot to shot. My lowest velocity was 319 while my highest velocity was 322 so not a big spread at all. This may seem a bit low but keep in mind it is a CQ (Close Quarters) Compact AEG Rifle purpose built for that situation, It is not really made for outdoor shooting where longer range shooting may be required.
For my Accuracy test, I placed a paper target 30 feet down range and actually ended up having to make this portion of my Test Video twice as two of my cameras did not cooperate with me and I do like to get multiple camera angels to make the videos a bit more interesting. For my second test I was able to get around a 1 inch group shooting 10 shots in semi auto. I did find the Bear River Black Ops SR4 CQ AEG Airsoft Rifle shot rather high so I had to place my aim point at the bottom of the rings on the papper target. This resulted in mid point shots but it did shoot a bit to the right. I would invest in either a red dot or perhaps some more adjustable iron sights for this Airsfot Rifle. As always I was shooting using a semi rested position sitting on a stool in the back rested on a sand bag up front. When I switched the sector to smile mode (Full Auto) I essentially did a mag dump of my remaining 50-60 rounds resulting in the grouping opening up to around 3 inches but this is expected with all those rounds being added to the grouping. Recoil was not really a factor as AEG Rifles don’t really move around all that much.
Overal the Bear River Black Ops SR4 CQ AEG Airsoft Rifle performed well for me in this Field Test Review. the FPS may seem a bit low but at close range it is more than enough and you don’t have to worry about hurting anyone so you can keep your mind on the game at hand. Accuracy was also in line with a mid range AEG Airsoft Rifle, perhaps even a bit better than most. The Bear River Black Ops SR4 CQ AEG Airsoft Rifle does come with a basic battery and charger but along with a better sighting system I would also invest in upgraded batters and charger to really complete this purchase. With the quad rail setup you can really make this AR Airsoft AEG your own in terms of customization, all that can be added at any time.
Type: Pellet Rifle. Manufacturer: Beeman Model: Black Panther Dual Caliber. Materials: Metal and Synthetic Plastic. Weight: 7.2pounds (2.3kg). Total Length: 44 inches (111.8cm). Barrel: 16.75 inches (42.5cm). Propulsion: Spring Piston. Action: Single Action Single Shot. AmmunitionType: .177 & .22 Caliber Pellets. AmmunitionCapacity: 1. MaxFPS: 495 Claimed.
Trigger Pull: The trigger on the Beeman Black Panther Dual Caliber Break Barrel Pellet Rifle is single action only requiring you to break the barrel and compress the internal spring piston before you can shoot it. This will also engage the safety which you have to disengage for each shot manually as an added security measure. The actual trigger pull is I would say a medium pull with an easy first stage then a more firm second stage. I am pretty sure the Black Panther uses the Sportsman tigger setup which does have some adjustment for trigger pull as far as I am aware of. Once I get a chance to shoot the Beeman Black Panther Dual Caliber Break Barrel Pellet Rifle I will be able to tell you more about how the trigger feels.
Accuracy: I have not performed any shooting tests with the Beeman Black Panther Dual Caliber Break Barrel Pellet Rifle so far, I will be making a Video Review next in the next few weeks “weather permitting” as I want to get outdoors for this test to be able to shoot the Black Panther at longer ranges. I expect the Beeman Black Panther Dual Caliber Break Barrel Pellet Rifle to perform well in the accuracy department using the 4x32 optical scope. In terms of power the spring does seem to take a bit of effort so I am hoping for a decent fps in both .177 caliber and .22 caliber!
Build Quality: The Beeman Black Panther Dual Caliber Break Barrel Pellet Rifle is made in China but looks to be fairly well made. It is mostly metal including the front and rear sights with a synthetic plastic stock and feels good to hold resting the cushioned rubber butt-pad to your shoulder. The stock and trigger guard are a one piece design, that said the trigger guard is fairly thick so it should stand up to some abuse.
Realism: The Beeman Black Panther Dual Caliber Break Barrel Pellet Rifle is not a copy of any real steel gun in production but does have that overall rifle shape to it so it looks like a gun but most people will be able to immediately see that it is a Pellet Rifle and that is exactly what it is since it is not trying to be a Replica Airgun or copy of any real steel rifle in production.
Pros:
All Weather durable ambidextrous synthetic stock.
All metal front and rear fiver optic sights.
Can shoot both .177 and .22 caliber pellets for multi purpose shooting.
Sportsman trigger (adjustable) with automatic safety system.
Comes with included 4x32 scope and mounts.
Very solid build at 9.92 pounds.
Nice cushioned rubber butt-plate looks good and adds to shooting comfort.
Has a scope-stop so your scope will stay nicely in place.
Cons:
Hard to tell if the claimed 495 fps is for .177 or .22 caliber lead or alloy pellets?
Hard to find this exact gun for info, not even on Beeman’s own website.
Made in China.
Comments: The Beeman Black Panther Dual Caliber Break Barrel Pellet Rifle is designed to be a more affordable Break Barrel Spring Piston Pellet Rifle with metal where it counts and a synthetic stock for durability and resiliency to weather conditions. You do have the option of shooting either .177 caliber pellets for a faster flatter trajectory or if you use the .22 caliber barrel, you benefit from perhaps a bit more downrange energy and less effect from windy conditions. You can also choose between shooting with the open fully adjustable metal sights or install the 4x32 scope for longer range shooting. You for sure get a versatile Spring Piston Air Rifle with the Beeman Black Panther Dual Caliber Break Barrel Pellet Rifle at the end of the day.
Type: Airsoft Rifle. Manufacturer: Bear River. Model: Black Ops SR4 CQ Materials: Mostly Metal. Weight: 6.2 pounds (2.8 kilograms). Length: 24-27.5 inches (610-699mm) BarrelLength: 7.8 inches (198mm) inner 6.06mm non-rifled. Propulsion: AEG. Action: Semi & Full Auto SAO. AmmunitionType: 6mm Airsoft BB's. AmmunitionCapacity: Mid Cap 300 rounds. FPS: 370 using .20 gram Airsoft BB’s.
TriggerPull: The trigger pull on the Bear River Black Ops SR4 CQ AEG Airsoft Rifle like pretty much every other AEG Airsoft Rifle I have reviewed is a SAO with a light and short trigger, typical of most AEG Airsoft guns having basically a trigger that is an electrical on/off switch. The trigger pressure I would say is about medium for this type of trigger and about a 1/4 inch in length. It has a curved metal trigger and works as expected.
Accuracy: I have not Field Test Reviewed the Bear River Black Ops SR4 CQ AEG Airsoft Rifle so far but I can only hope it performs as well as the Bear River Black Ops SR4 CQ AEG Airsoft Rifle I reviewed already as it really surprised me for such a low cost entry level AEG Airsoft Rifle. Bear River claims around a 370fps using .20 gram Airsoft BB’s but they do recommend using .25 gram or heavier Plastic BB’s. We will find out when I do my actual Field Test Shooting Video for it. Similar with accuracy, we will have to wait till my shooting video to know how the Bear River Black Ops SR4 CQ AEG Airsoft Rifle performs on a paper target in the Replica Airguns Indoor Sea Can Shooting range.
Build Quality: Build quality for the Bear River Black Ops SR4 CQ AEG Airsoft Rifle is exceptional with nearly the entire Airsoft Rifle made out of some sort of metal including the receiver, hadn't guard, buffer tube, barrel, sights, trigger, charging handle, sights and all of the controls. Internally you will find a full metal Gen. 3 gearbox from SRC with with 8 mm metal bearing bushings, metal spring guide, upgraded metal piston head, cylinder, and cylinder head, and pre-shimmed all steel gears. The Hop-up is also metal and Bear River has installed a high torque long axle motor from SRC along with a metal hop-up.
Realism: The Bear River Black Ops SR4 CQ AEG Airsoft Rifle like so many other AEG AR type Airsoft Rifles is super realistic, with the Black Ops SR4 CQ it takes it to the next level with so much equality and metal everywhere. Because of this it is fairly heavy for such a compact AR Rilfe coming in at over 6 pounds which does make it feel super solid to hold.
Pros:
Super compact CQ style AR.
Comes with charger and 9.6 volt Ni-MH battery to get you started.
Lots of mounting points for accessories.
Iron sights have 4 aperture option peep sight options.
6 position rear stock for different shoulder pull lengths.
Adjustable metal hop-up under dust cover.
Semi and full auto selectable.
Almost all metal build with good weight and feel to it.
Black Ops branding looks good.
Great looking Compact AR Replica.
Cons:
No dedicated bolt release.
Will want to upgrade battery soon to get the most out of it.
Sights are non adjustable.
Comments:
The Bear River Black Ops SR4 CQ AEG Airsoft Rifle for the price is a real deal as far as I am concerned selling currently for just over $400 in the Canada Replica Airguns Store, and $299 in the US Store. Keep in mind that also includes the 9.6 volt battery and charger to get you started, (I would recommend an 11.1 volt LIPO battery for higher RPM and a more responsive trigger). I really like more compact Rifles as I just like the look and they are easier to maneuver on the field or indoors with less bulk to get in the way. For the price you get a lot with the Bear River Black Ops SR4 CQ AEG Airsoft Rifle so if you are on a bit of a budget but still want all the bells and whistles then go for it!
Type: Airsoft Rifle. Manufacturer: Specna Arms. Model: RRA SA-CO2 Materials: Metal and Plastic. Weight: 4.96 pounds (2.25 kilograms). Length: 27.5-31 inches (699-787mm) BarrelLength: 10.63 inches (270mm) inner 6.03mm tight bore non-rifled. Propulsion: AEG. Action: Semi & Full Auto SAO. AmmunitionType: 6mm Airsoft BB's. AmmunitionCapacity: Mid Cap 450 rounds. FPS: 410 using .20 gram Airsoft BB’s.
TriggerPull: Like almost every other AEG Airsoft Rifle I’ve reviewed in the past, the trigger pull on the Specna Arms RRA SA-CO2 AEG Airsoft Rifle is a SAO with a light and short trigger feel. Most AEG Airsoft Rifles basically have a trigger that is an electrical on/off switch. The trigger pressure is not super light but for sure not heavy and the pull length is about a half centimeter long (quarter inch or so) and when you get to the end it basically actives the electric motor which compresses the spring allowing for semi or full auto shooting depending on what you have selected. Keep in mind higher voltage batteries will wind faster and make the hesitation shorter from the time you pull the trigger till the spring releases and shoots a BB.
Accuracy: In most cases I make my Table Top Review Video for each gun I review first, so I will not be able to share my experience of how this Specna Arms RRA SA-CO2 AEG Airsoft Rifle performs as that experience has not happened yet. I am planning to make my Field Test Shooting Video in a couple of weeks so stay posted for that video. You can watch a similar Specna Arms Core AEG Airsoft rifle video I have made previously showcasing a Core versus Edge series. The Specna Arms RRA SA-CO2 AEG Airsoft Rifle should performs about the same as a similar Core AEG Airsoft Rifle from Specna Arms.
Build Quality: Generally speaking from my past hands on with Sepcna Arms products both in Core and Edge version, they have been good in terms of quality and build. The Core versions will be a step down from the Edge version but they have still proven to perform well and hav a good overall build with decent internals no matter which version you decide to go with. I will say I did experience a problem with my Specna Arms RRA SA-CO2 AEG Airsoft Rifle when I pulled the charging handle back I had a fairly major malfunction with it. I am fairly sure the spring got jammed and now the charging handle will not spring back into forward resting position. This should not affect my Field Test Shooting Video as the only real purpose of this type of charging system is to open the dust cover and allow access to the hop-up system. I can still do this but need to pull back the hop door manually. Getting back to build quality, you get a plastic reacievr, buffer tube, carry handle, fore grip, magazine, rear stock and pistol grip. Metal can be found in most of the controls, the barrel and of course the trigger.
Realism: Other than the Specna Arms RRA SA-CO2 AEG Airsoft Rifle having a fair amount of plastic components it is a very realistic copy of a similar styled AR type Rifle. It will be a bit lighter but feels decent to hold and you can add a bit of mass by swapping out the carry hand and fore grip with metal versions.
Pros:
More classic AR15 look to it if you prefer that.
Quality components throughout even in the lower priced Core series.
ESA™ quick spring change system makes spring changes quick and easy.
Comes with two springs for potential indoor and outdoor usage.
Plastic parts are fiberglass reenforced making them very durable.
Fully adjustable peep sight with two aperture positions.
No orange tips on our Canada Store versions.
6 position rear stock for varies shoulder pull lengths.
Metal V2 Gearboxes with metal gears and mostly all metal parts inside.
Easy access to motor for any possible trouble shooting you any need to do.
Cons:
Plastic receiver.
Charging handle had a major malfunction in my demo unit.
You will need a more compact and specific battery size/type with this style of AR AEG.
Comments:
It is unfortunate that my review version of the Specna Arms RRA SA-CO2 AEG Airsoft Rifle was defective, this can happen to any product ever high end Airguns. It does not happen very often thankfully and this would be the first time it has happened to me with a Specna Arms Product so don’t be too hard on them. Fortunately I should still be able to make my Field test Shooting Video and get that info out to everyone. As it stands I think the Specna Arms RRA SA-CO2 AEG Airsoft Rifle is well priced and good value (in 100% working condition of course). Personally I would look more at the Edge series as the quality is a for sure a big step up but not everyone has a big budget so get what works best for your needs and budget.
Type: Airsoft Rifle. Manufacturer: S&T Model: KAR98K Materials: Metal & Wood. Weight: 3300 grams (7.28 pounds). Total Length: 1120mm (44.1 inches). Barrel: 483mm (19 inches) Smooth bore. Power Source: Spring Piston. Action: Bolt Action - Single Action Only. Ammo Type: 6mm Airsoft BB. AmmoCapacity: 11 Round Magazine. FPS: 380-420.
Trivia: The Karabiner 98 kurz (German: "carbine 98 short", often abbreviated Kar98k or K98k and often incorrectly referred to as a K98 (which was a Polish Carbine) is a bolt-action rifle chambered for the 7.9257mm Mauser cartridge that was adopted on 21 June 1935 as the standard service rifle by the German Wehrmacht. It was one of the final developments in the long line of Mauser military rifles. Although supplemented by semi- and fully automatic rifles during World War II, it remained the primary German service rifle until the end of the war in 1945. Millions were captured by the Soviets at the conclusion of World War II and were widely distributed as military aid. The Karabiner 98k, therefore, continues to appear in conflicts across the world as they are taken out of storage during times of strife.
Trigger Pull: The trigger pull on S&T Matrix KAR98K Bolt Action Airsoft Rifle is a single action only trigger as the bolt action not only compresses the spring but also readies the trigger for release making the trigger pull short and light. There is a short amount of takeup with a crisp and light release.
Accuracy: I have not shot the S&T Matrix KAR98K Bolt Action Airsoft Rifle so far but plan to make a full dedicated Field Test Shooting Video shortly to find out what the actual real world velocity and accuracy will be. So stay posted for my upcoming shooting test in a few weeks time…
Build Quality: The build quality for the S&T Matrix KAR98K Bolt Action Airsoft Rifle is really good as it is made almost exclusively of either metal or wood. The stock is finished in a dark walnut stain and the metal has a rustic finish about it which is what you would find in a real steel aged version. You will also find a CNC Aluminum body along with a Reinforced metal barrel, bolt assembly and internals. The S&T KAR98K has a quality feel about it inside and out.
Realism: As mentioned earlier the finishes has a less refined look adding to the realism, that combined with the real wood stock really makes this Bolt Action Airsoft Rifle supper believable as a Replica Airgun. The only real giveaway is when you pull the bolt back and it is a solid unit with no visibility in to the magazine area. Other than that the S&T Matrix KAR98K Bolt Action Airsoft Rifle is a solid copy of the real steel version.
Pros:
Super believable replica of the real Kar98k.
Very solid build quality weighing over 7 pounds.
Realistic materials including the real wood stock.
CNC Aluminum body.
Reinforced metal barrel, bolt assembly and internals.
No need for a battery or to use CO2 or gas.
Adjustable rear sight on the fly for elevation.
Bolt action feels smooth.
Easy to adjust Hop-up.
Cons:
Does come with a red tip (should be able to remove).
Rear sight not adjustable for windage.
No sling included, would have been nice.
Bolt does not allow to see into magazine area.
Comments:
The S&T Matrix KAR98K Bolt Action Airsoft Rifle looks and feels the part for sure and has a lot of quality going on with it’s real wood stock and quality metal throughout. I love the finish of not only the wood stock but also the metal parts as they have a less refined and aged quality about them that would be similar as to how a real World War 2 rifle would look today. If you want an ultra realist bolt action World War 2 Carbine that you can shoot almost anywhere, then look no further. OK the sticker price on this one is a bit higher than some, but again so is the quality so if that's important to you be prepared to pay a bit more.
In this Replica Airguns Unboxing Video I take a look at 6 Airguns consisting of 2 Paintball Pistols, 3 Airsoft Rifles and one Pellet Rifle. This is not a full review in any way but is rather a preview of what i will be doing full Reviews for over the next several weeks.
This is not exclusive to Airguns since trends of Airguns are highly influenced by what type of Real Steel Pistols are popular to people. This is often based on what people see portrayed in movies and TV Series, and also promoted online. There is for sure an overlap in what is popular and it is hard to say what is influencing what? Is it the popularity of Pistols out in the real world that influences what we see being used in the movies and on TV? Or is it what we see in Movies and TV that influences our choices of pistols out in the real world? Perhaps it is a combination of both?
My list is based on my own personal experience and does not represent the entirety of types of Pistol designs available.
Last week I individually tested out the Barra Black Ops M4 Viper MK5 and the Krytac LVOA-C AEG Airsoft Rifles here in the Replica Airguns Indoor Sea Can Shooting Range to see how well they would perform. I was very surprised at how closely they performed considering the Barra Black Ops is around a quarter of the cost of the Krytac LVOA-C.
My testing in the Indoor Sea Can is a bit limited in terms of range as I can only set a target to about 30 feet away given the limitations of my 40 foot Sea Cam. I really wanted to take both of these AEG Airsfot Rifles and test them out at much longer ranges to see if the much lower cost Barra Black Ops M4 Viper MK5 could compete with the Krytac LVOA-C Airsoft Rifle at 50 feet and 100 feet respectively. So that’s exactly what I did! I did use a bit heavier Airsoft BB’s (.28 gram) for the longer range outdoors and much windier shooting conditions but I do have to say it was a bit windy on my testing day which I am sure played a roll.
I did place a few pre-test shots downrange at my 100 foot target to get an idea of where I needed to place my aim point and this did help me a bit to get in the ball park but by no way was a bang on in terms of sighting in. Because of this I did have to make some on-the-fly adjustments as I tested but was able to get rounds on paper at 100 feet even with the wind gusts.
In this second video I test out the more expensive of the two AEG Airsoft Rifles, the Krytac LVOA-C AEG Airsoft Rifle to see how it compared to my previous Barra Black Ops M4 Viper MK5 test. I was a bit surprised at the results expecting the Krytac LVOA-C Airsoft Rifle to be the clearly superior option. As it turns out there was actually very little difference at least in term of accuracy out of the box. That said the Krytac LVOA-C had a much more responsive trigger with virtually no delay between pulling the trigger and actual BB’s being fired. This also makes full auto shooting a completely different experience as the Krytac LVOA-C rounds per minute is out of this world!
Last week I individually tested out the Barra Black Ops M4 Viper MK5 and the Krytac LVOA-C AEG Airsoft Rifles here in the Replica Airguns Indoor Sea Can Shooting Range to see how well they would perform. I was very surprised at how closely they performed considering the Barra Black Ops is around a quarter of the cost of the Krytac LVOA-C.
My testing in the Indoor Sea Can is a bit limited in terms of range as I can only set a target to about 30 feet away given the limitations of my 40 foot Sea Cam. I really wanted to take both of these AEG Airsfot Rifles and test them out at much longer ranges to see if the much lower cost Barra Black Ops M4 Viper MK5 could compete with the Krytac LVOA-C Airsoft Rifle at 50 feet and 100 feet respectively. So that’s exactly what I did! I did use a bit heavier Airsoft BB’s (.28 gram) for the longer range outdoors and much windier shooting conditions but I do have to say it was a bit windy on my testing day which I am sure played a roll.
I did place a few pre-test shots downrange at my 100 foot target to get an idea of where I needed to place my aim point and this did help me a bit to get in the ball park but by no way was a bang on in terms of sighting in. Because of this I did have to make some on-the-fly adjustments as I tested but was able to get rounds on paper at 100 feet even with the wind gusts.
In this first video I test out the cheaper option Barra Black Ops M4 Viper MK5 AEG Airsoft Rifle on its own, my next video will be exclusively the Krytac LVOA-C AEG Airsoft Rifle in which I will wrap up with my conclusion of both AEG Airsoft Rifles. I think you will be surprised at the results but you will have to wait a bit to find out!
In this Filed Test Shooting Video for the Krytac Warsport LVOA-C AEG Airsoft Rifle I test out the claimed velocity and then the general accuracy in both semi and full auto to find out if spending top dollar gets you top results. If you want more information on specifications and details along with more close up video then make sure to watch my Krytac Warsport LVOA-C AEG Airsoft Rifle Table Top Review Video already uploaded.
Krytac claims the Warsport LVOA-C is able to shoot a velocity of around 390-410 fps using .20 gram Airsfot plastic BB’s and by God it does. I was able to get an average 6 shot result of 402 fps with the slowest shot hitting 400 fps and the fastest shot toping out at 404 fps. This is ideal for most Airsoft Game shooting situations, having enough power to shoot out at fairly far away targets without hopefully injuring anyone that may get shot closer in.
For my Accuracy Test of the Krytac Warsport LVOA-C AEG Airsoft Rifle I first shot 10 rounds into a fresh paper target placed 30 feet down range using a rested up front and sitting in the back shooting position. I. Was not able to use the rear stock as my battery configuration was too bulky and did not allow for this so not being able to shoulder the Krytac Warsport LVOA-C AEG was not ideal but I got it done. My 10 shot semi auto grouping resulted in a solid 1 inch grouping, I did have one round come out just a tad but that was more than likely human factor rather than the gun. In terms of shot placement out of the box the Krytac Warsport LVOA-C was almost right on sight with a good amount of shots in the bullseye but leaning a bit to the left and a smidge low. You could easily adjust the sights to be dead on as they are fully adjustable. I then repeated this test but in Full Auto and basically emptied the 300 round magazine amazingly quickly and this time my grouping spread out an additional inch to 2 inches. Remember this was for 200+ total rounds!
So do you get what you pay for? Sure you do, I would say this AEG Airsoft Rifle has one of the fastest rates of fire I have tested to date, it is almost like shotgun a gatling gun! Additionally I really like the mid/high cap magazine design that does not have a standard spring tensioner you need to wind between groups of shots. Basically just use a speed loader to fill it up and shoot till it’s empty. Overall performance was really good as the testing showed. I would like to get this AEG Airsoft rifle outside and test it out at longer ranges to see how it stacks up against a lower costs AEG Airlift Rifles. Maybe that will be my next video? But for now I can for sure recommend the Krytac Warsport LVOA-C AEG Airsoft Rifle to anyone looking for a high end AEG AR styled Airsoft Rifle.
