This is part two of my three part Indoor Filed Test Shooting Video for the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol. In this second video I test out the velocity and energy shooting 5 rounds through my Chronograph, using the 2.7 gram Rubber/Steel Balls that I purchased on my own to test with this Less Lethal Pistol. I also shoot 5 rounds into a paper target setup 30 feet down range to get an idea on what to expect accuracy wise with the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol. In video three I plan to test out the 8 gram all Steel Balls to see they are a viable option with a CO2 Pistol like this designed for much lighter rounds . If you have not watched my Table Top Video for the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol, then make sure to do so for closer up video and all the specifications and details.
Umarex claims a max velocity of 485 fps with an energy rating of 13 Joules with the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol when using their supplied ammo. I am assuming this would be using the Powder Balls as they seem to be a bit lighter than the Rubber Balls and will have the highest velcoity. In my Chronograph testing I shot 5 rounds using the 2.7 gram Rubber/Steel balls. The velocity for the 2.7 gram Rubber/Steel Balls was slower as expected but they did stay fairly consistent ranging from a low of 300 fps to a high of 309 fps averaging 304 fps. The overall energy rating ended up being 12 Joules, so obviously lower in fps than claimed by Umarex but close to the claimed 13 Joules. Still a good result close to the claimed raw energy.
The main point to this ammo comparison video is to finds out not only if the heavier 2.7 gram Rubber/Steel Balls will have around the same energy as the lighter 1.6 gram all Rubber Balls, but also to see if they have similar accuracy. In terms of accuracy the 2.7 gram Rubber/Steel Balls did just a little bit better than the 1.6 gram all Rubber Balls, not by a lot but, by about 1 inch with a 5 round grouping of 5 inches. All 5 shots were well entered shooting just a bit high of my aim point by about 3 inches but in general well centered left to right as a grouping.
I was happy with the performance of the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol using the 2.7 gram Rubber/Steel Balls for this second Field Test. Energy was very close to the claimed 13 Joules and the average 304 fps I got with this ammo felt snappy and got to the target quickly and sounded like they really hit hard. I do like the higher 15 Joules and 450 fps I got from the lighter 1.6 gram all Rubber Balls, so at this point I would probably recommend sticking with them for the most power and energy down range. Next up I test out the 8 gram all Steel Balls to find out if they are even an option or if they are simply juts to heavy for the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol.
This is part one of my three part Indoor Filed Test Shooting Video for the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol. In this first video I test out the velocity and energy shooting 5 rounds through my Chronograph, using the 1.6 gram included Rubber Balls that came with it and then I also shoot 5 rounds into a paper target setup 30 feet down range to get an idea on what to expect accuracy wise with the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol. In video two I will be testing out the 2.7 gram Rubber/Steel Balls in the same way, and then in video three I will be testing out the much heavier all steel 8 gram rounds to see if they are even usable in a CO2 Airgun designed for much lighter rounds. If you have not watched my Table Top Video for the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol, then make sure to do so for closer up video and all the specifications and details.
Umarex claims a max velocity of 485 fps with an energy rating of 13 Joules with the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol. In my Chronograph testing I shot 5 rounds using the 1.6 gram included all rubber balls. I did throwout the first shot as it was about 50 fps lower than the rest, perhaps as it was first out of the barrel which can happen. The other 4 rounds averaged 445 fps with an overall energy rating of 15 Joules, so a bit slow in fps than claimed by Umarex but a higher energy output. Perhaps the fps rating was for lighter rounds like the included 10 powder balls? Still an excellent result with more raw energy than expected which is great for a system designed to deter an intruder!
What good is power if you can not hit the target? That’s why I always test out accuracy as you want your gun to shoot where you point it. With Rubber Balls they tend to “wing” or “curl” a bit in the air which does spread out the groupings a bit over a BB or even Airsoft gun, so I was not expecting under a 2 inch grouping. My goal was to hit the target fairly centered with around a 6 inch grouping and the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol did exactly that for me, so mission accomplished. I also wanted to find out how many shots to expect from a fresh 12 gram CO2 and my results showed around 20 shots, so you can reload the internal magazine around 4 times before the trigger stops working, which is how you know the CO2 pressure is not adequate enough to shoot any more rounds.
I was very happy with the performance of the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol using the included 1.6 gram All Rubber Balls for this Field Test. Energy was even 2 Joules higher than claimed by Umarex, and I did not have a single malfunction with this pistol through my testing of all types of ammo I used in videos 1, 2 and 3. I would say the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol is your best option as a Less Lethal Pistol here in Canada. Will it stop a very determined intruder? Maybe not, but I would feel a little bit safer with the Umarex T4E P2P HDP 50 Gen 2 CO2 Less Lethal Pistol at my side than not having it at all. And a couple well aimed rounds to some soft tissue will for sure make someone reconsider some of their life choices. Stay posted for videos two and three coming out shortly…
Type: Less Lethal Pistol. Manufacturer:Umarex - T4E. Model:P2P HDP 50. Materials: Metal & Polymer. Weight: 1.5 pounds (.7 kg). Barrel: 4 inches (10.2 cm) Smooth bore. Total Length: 8.5 inches (21.6 cm). Power Source: 1x12 gram CO2. Action: Semi auto - Double action only trigger. Ammo Type: .50 Caliber Rubber Ball, Pepper Ball, Powder Ball. Ammo Capacity: 6 Round spring fed internal magazine. FPS: 485 (13 Joules).
Trigger Pull: The trigger pull on Umarex P2P HDP 50 Gen 2 CO2 Less Lethal Pistol is double action only but not overly long or heavy. There does not seem to be any ammo friction which is nice, so the each round feels about the same with spring tension not playing a factor. In order to use the trigger, the Pistol will need to be fully charged by loading a 12 gram CO2 and giving it a smack on the bottom of the pistol grip. This will pierce the CO2, charging the gun with pressure and activation the trigger mechanism. When the CO2 pressure becomes too low, the trigger will not function and a fresh CO2 will needed to be swapped over.
Accuracy: So far I have only briefly tried out the Umarex P2P HDP 50 Gen 2 CO2 Less Lethal Pistol here in the Replica Airguns Indoor Airgun Shooting Range, and I was rather impressed at the initial performance as it did seem to be moving the .50 call rubber balls I was shooting at close to 500 fps with a lot of energy as my pepper and cardboard target was dislodged from the backstop after a few shots. Accuracy seems to be as expected from a Paintball type pistol, so I am expecting to get around a 4-6 inch 6 shot grouping at 30 feet away which will be effective in a Less Lethal encounter.
Build Quality: The build quality of the Umarex P2P HDP 50 Gen 2 CO2 Less Lethal Pistol is good overall. It is mostly made out of plastic which is fine, as I feel that if it was mostly metal, and because of its larger size, it would be on the heavy side and not something you may want to use in a cary situation if that was your plan. There is metal where it needs to be in most of the mechanical areas including the barrel, trigger, charging system and I am sure other internal parts. The plastic parts feel well made and fit and finish is very good. The Umarex P2P HDP 50 Gen 2 CO2 Less Lethal Pistol does have more than enough weight at 1.5 pounds to feel solid in the hand.
Realism: This version of the Umarex P2P HDP 50 Gen 2 CO2 Less Lethal Pistol comes with the orange slide to show that it is not a lethal firearm. I have seen all black version but at this time we only sell the colored slide version. This does make it obvious that the Umarex P2P HDP 50 Gen 2 CO2 Less Lethal Pistol is not a “Real Firearm” designed for lethal encounters, which in Canada is a good thing since our self protection laws seem to favor the criminal more than the victim. So making sure you are using a tool designed to deter a criminal rather than harm or kill them, is hopefully going to keep you out of trouble with the law. That said the Umarex P2P HDR 50 Gen 2 CO2 Less Lethal Pistol does look like a modern semi auto pistol and functions much the same but with less force.
Pros:
Not many options for a true less-lethal option here in Canada. This Airgun is purpose built for less lethal use so it has what I believe is enough power to actually dissuade most intruders.
In this case I like that it is clearly marked in orange to indicate it is not an actual lethal firearm. When protecting yourself in Canada you have to be cautious with your intentions, and having clear orange markings will help in your case to show that you where not trying to give the impression of using a real firearm.
Nice powerful 485fps with a 13 Joules energy rating.
Can store the 12 gram CO2 in it and activate with a quick hit to the bottom of the CO2 screw.
Holds 6 rounds in the internal magazine which hopefully gets the job done. Should be able to reload at least one more time for a total of 12 shots per 12 gram CO2.
Fiber Optic sights make it easy to line up your target in most lighting conditions and backgrounds.
Double action trigger feels smooth and not too heavy or long, also has a trigger safety on it.
Can add a tactical light or laser to the under barrel picatinny rail.
Comes with 10 rubber and 10 powder balls to get you started.
Cons:
It is a bit on the larger size, not going to be easy to cary if that is your plan. I do not know what the legal ramifications of carrying this would be as it is clearly designed for protection and not for lethal encounters.
Not a lot of shots per CO2 but the idea here is to quickly deliver as much damage as possible, this is not a weapon for prolonged gun fights.
In Canada it does not seem you can get pepper balls easily most likely due to import regulations.
Comments:
The Umarex P2P HDP 50 Gen 2 CO2 Less Lethal Pistol is a very refreshing product for us here in Canada as up until now similar styled Rubber Ball purpose built self defense products we have been able to get, in my opinion simply did not have enough power to really be effective other than the initial intimidation of holding what looks like a firearm. If it came down to actually shooting it, I don’t believe there would be enough stopping power to deter an intruder. The Umarex P2P HDP 50 Gen 2 CO2 Less Lethal Pistol on the other hand has a 485 fps, 13 Joules power rating which is a rather big jump from other similar products available to us here in Canada and although it may not stop everyone, I do believe you have a much better chance protecting yourself with the Umarex P2P HDP 50 Gen 2 CO2 Less Lethal Pistol. If you are looking for something to have at home to help you feel a bit safer, then the Umarex P2P HDP 50 Gen 2 CO2 Less Lethal Pistol is the absolute best option for Canadians at this time.
This was a really fun Unboxing Video for me as I received something I feel a lot of Canadians might be really interested in protecting yourself in Canada is not a right especially if you use lethal force. So having a less lethal option is a really good idea.
Let’s get into what I found in this most recent Mystery Box in order of appearance…
The first item I unboxed was the KWC SP2022 CO2 NBB 4.5mm Steel BB Pistol. A pretty basic 4.5mm CO2 BB Pistol mostly made out of plastic but with a full size 21 round drop out metal magazine that does help a lot to add some much needed weight to this Airgun. It uses standard 12 gram CO2 with a claimed velocity of 450 fps.
Probably the most exciting item I pulled out of this months Mystery Box was the Gen2 Umarex P2P HDP 50 Rubber Ball purpose built Less-lethal solution for personal and family protection. Most of the similar Rubber ball Less-lethal Airguns I have tested generally do not pack enough punch to really be much of a deterrent in my opinion but the Gen2 Umarex P2P HDP 50 has a claimed 495 fps and when I tested it out after making this video it defiantly has some power. I would not want to be at the receiving end of this product especially in close proximity. The Gen2 Umarex P2P HDP 50 uses a traditional 12 gram CO2 and holds 6 rounds of rubber ball or powder ball, it does come with 10 of each to get you started.
Next I took a look at three KJWORKS Airsoft Pistols all of which came with CO2 Magazines, extension barrels and thread on tips. The KJWORKS KP-19, the KJWORKS M9A1 TBC, and the KJWORKS KP-13 TBC. As expected with KJWORKS Airsoft Guns, they looked really good and will be a joy to review and test out.
Last out of the Mystery Box was a new product from Umarex, a full sized Marlin Cowboy Lever Action BB Rifle in the style of the classic Red Ryder BB Gun but as mentioned in a larger size more suitable for an adult. Hey why do the kids get to have all the fun? The Umarex Marlin BB Rifle holds 650 rounds in its BB hopper and has a claimed fps pf 300. It also has an adjustable for elevation peep sight in the back with a metal lever and a Classic Faux Wood Finish.
I have reviewed a few other Umarex T4E .43 Caliber Paintball Airguns in the past so if you have watched any of those than you already have a pretty good idea what to expect from the Umarex T4E PDP Compact Walther .43 Cal CO2 Blowback Paintball Gun. As with all my Field Test Shooting Videos I first test out the velocity in fps shooting 5 rounds through my Chronograph and averaging them out. I then place a full magazine generally into a paper target setup 30 feet down ranged see what the accuracy looks like. Make sure to also watch my Table Top Video for the Umarex T4E PDP Compact Walther .43 Cal CO2 Blowback Paintball Gun for more information about specifications, details and some close up video.
For my velocity test I placed a brand new 12 gram CO2 in the Umarex T4E PDP Compact Walther .43 Cal CO2 Blowback Paintball Gun and shot 5 rounds through my Chronograph, getting an average fps of 322. The fastest shot hit a velocity of 331 fps with the slowest shot hitting 311 fps so all pretty close together. I was using standard .43 caliber rubber balls as they are a lot less messy here inside the indoor sea can Airgun shooting range. I didn't check the temperate but generally I keep iti comfortable, so around 20 degrees Celsius or 68 degrees Fahrenheit.
Next up I shot a full magazine which is 8 rounds for the Umarex T4E PDP Compact Walther .43 Cal CO2 Blowback Paintball Gun. Paintball guns are not known for their accuracy but I was impressed with the base grouping I got from the Umarex T4E PDP, It shot really well centered with 6 rounds all within about 3 inches of each other. 2 rounds did “wing out” a bit increasing the grouping to closer to about 6 inches but still a good grouping from a paintball gun design not so much to be super accurate but to be able to hit human sized targets ate realistic ranges which it does do very well.
I am not sure if this is the best test result for an Umarex T4E Paintball Airgun I have ever done but for sure it is one of the best for what I remember. Velocity was right on the mark and accuracy was again very good. I would be very confident in the performance of the Umarex T4E PDP Compact Walther .43 Cal CO2 Blowback Paintball Gun out in the field. I also think it is one of the nicer looking Umarex T4E .43 Caliber Paintball Pistols but if you are more of a Glock or S&W person there are options form Umarex for you too so make sure to check out our selection of Paintball Airguns over on our our Canada and US Replica Airgun Stores.
Type:Paintball Gun. Manufacturer:Umarex - T4E. Model:Walther PDP. Materials: Metal & Polymer. Weight: 690 grams (1.52 pounds). Barrel: Smooth bore. Power Source: 1x12 gram CO2. Action: Semi-Automatic with blowback action. Ammo Type: .43 Caliber Paintball or Rubber Ball. Ammo Capacity: 8-9 Rounds. FPS: 300.
Trigger Pull: The trigger pull on the Umarex T4E PDP Compact Walther .43 Cal CO2 Blowback Paintball Gun feels a lot like a double action trigger in length of pull and weight. When you pull the trigger back, there is an inner barrel that retracts back into the magazine sealing off a Paintball for more efficient CO2 usage, but this does cause some trigger drag and friction. There is also a working trigger safety which is a nice safety feature.
Accuracy: So far I have not had the opportunity to test the Umarex T4E PDP Compact Walther .43 Cal CO2 Blowback Paintball Gun out, so stay posted for a future Field Test Shooting video where I will see what kind of fps and accuracy we can expect from it. I have made a Field Test Shooting Videos for the Umarex T4E Walther PPQ M2 CO2 Blowback .42 Caliber Paintball Pistol so have a watch of that video as the performance of the Umarex T4E PDP Compact Walther .43 Cal CO2 Blowback Paintball Gun should be about the same.
Build Quality: The build quality of the Umarex T4E PDP Compact Walther .43 Cal CO2 Blowback Paintball Gun is really very good, metal parts are where you would expect them to be, as in the slide, slide catch, barrel, magazine and most internal parts. This gives the Umarex T4E PDP Compact Walther .43 Cal CO2 Blowback Paintball Gun a nice 1.5 pound weight to it with the magazine in which makes the Paintball version pretty close to the real still version. The Umarex T4E PDP does have a polymer frame but again this is normal with todays modern guns and helps keep the weight down. Fit and finish is also excellent.
Realism: The Umarex T4E PDP Compact Walther .43 Cal CO2 Blowback Paintball Gun is a very close replica of the real steel Walther PDP, from the fully licensed trademarks to the large .43 caliber diameter barrel. If you placed the Paintball version side by side with the real steel version, I doubt you would be able to easily tell them apart without actually handling them? You will find that the slide cycle distance is a much shorter than it would be with the real steel version, meaning that when the side cycles rearward or the slide catch is engaged, the slide does not go as far back as it should. Filed stripping the Umarex T4E PDP Compact Walther .43 Cal CO2 Blowback Paintball Gun will require tools however.
Pros:
Really great weight and solid feeling gun.
Full Metal slide that locks back on the last shot.
All metal heavy full size drop out magazine adds some additional weight to the pistol.
Very Accurate Walther PDP replica, almost indistinguishable from the real steel version until you really examine it up close.
Everything works pretty much like the real gun so a great training tool.
White dot sights front and back, rear sight is adjustable for windage.
Working trigger safety.
Fit and finish is excellent.
Magazine spring release really shoots the magazine out making it easy to grab.
Can mount a red dot on the rear of the slide and comes with lots of mounting plate options.
Comes with a nice hard shell case for storing it in and locking it up.
Love the .43 caliber barrel opening, adds to realism.
Cons:
The trigger is a bit long as it shoots more like a double action trigger.
Magazine only holds 8-9 rounds, so you are going to need extra magazines or get quick at reloading.
Blowback action is not full blowback, more like a typical partial blowback CO2 BB airgun.
Comments:
Umarex and T4E working together have put out a nice line of .43 caliber CO2 Blowback Replica Paintball Training guns focusing on the Walther, Glock and HK Brands as Umarex holds a license with all of these gun manufactures. The realism is excellent not only in looks but also in function making their use as training weapons that much more valuable. If you are looking for the most realistic Replica Paintball Pi thenstol, Umarex T4E products are your best option and it is nice that we now have several models to choose from that may coincide with your standard side arm of choice.
In this Field Test Shooting Video for the Barra 1866 Lever Action 22 Cal CO2 Pellet Rifle, I get to test out a Replica .22 Caliber CO2 Rifle which I don’t get the chance to do so very often and .22 caliber combined with a Replica in a an Airgun is very uncommon! Well today I got to test one out and it was a lot of fun, I would say it performed very well for me. As usual, my main goal is to find out what the real world velocity is in fps and also to see how accurate the Barra 1866 Lever Action 22 Cal CO2 Pellet Rifle is shooting at a paper target 30 feet away. Also make sure to checkout my Table Top Video for the Barra 1866 Lever Action 22 Cal CO2 Pellet Rifle for more details and specifications and close up video.
First in my to-do list was the velocity portion of my Field Test, and so I loaded up dual 12 gram CO2 cartridges into the Barra 1866 Lever Action 22 Cal CO2 Pellet Rifle along with 10 preloaded .22 caliber shells. By the way I was using Gamo 15.43 grain (1 gram) lead pellets and the temperature was just a bit below room temperature, so not 100% ideal for maximum velocity but still warm enough for my purposes. The Barra 1866 Lever Action 22 Cal CO2 Pellet Rifle shot an average 5 shot velocity of 390 fps with the fastest shot hitting 411 fps and the slowest performer hitting 370 fps. That works out to 5.78 average foot pounds of energy.
Next up, I first recovered the 5 ejected shells I used in the velocity test, and again reloaded them with some more pellets and then back into the Barra 1866 Lever Action 22 Cal CO2 Pellet Rifle for my accuracy test. Keep in mind with a lever action rifle, I have to remove the rifle from my shooting position each time to work the lever action and chamber a round. This does cause me to have to fully reset for each shot which does kind of break a shooting grove just a bit, but it did not seem to make much of a difference as my accuracy results where still very good. I did notice vertically the grouping was about 2 inches while side to side it was closer to 1 inch. I attribute this to the sighting system as it was hard for me to focus on the rear sight and make sure I had it perfectly level with the front sight for each shot, which would account for some variation in elevation. The Barra 1866 Lever Action 22 Cal CO2 Pellet Rifle was also shooting about 2 inches high from my aim point.
I have said this a bunch of times before, but I do really love shooting lever action rifles. Even a low cost Red Ryder BB Rifle brings a smile to my face. I also have a Henry Lever Action 22LR that I also really enjoy shooting when I get the chance. The Barra 1866 Lever Action 22 Cal CO2 Pellet Rifle is a really sweet looking rifle that performs as good as it looks thankfully! It’s also well priced for what you get in my opinion at just under $300 Canadian at the time of this video. If you want a fairly powerful Replica Air Rifle that hits hard and true and is super fun to shoot then get this one but make sure to get a bunch of extras shells cause they like to disappear on you pretty quickly. For now I still have all 10 of mine but they love to hide in the craziest places when they get ejected :)
In this Indoor Field Test Shooting Video, I put the EMG SAI 2011 DS 4.3 CO2 Blowback Airsoft Pistol through my usual performance shooting test by first finding out what the velocity is by shooting 5 rounds through my Chronograph using a fresh CO2 along with .20 gram Airsoft BB’s. I follow this up with a 10 round accuracy test, again using .20 gram Airsoft BB’s and shooting at a paper target setup 30 feet down range, while seated on a stool in the back with my hands rested on a sand bag up front. This generally works pretty well and helps me get the most out the gun I am testing. If you are also interested in details and specifications than make sure to watch my Table Top Video I already made for the EMG SAI 2011 DS 4.3 CO2 Blowback Airsoft Pistol.
So how did the EMG SAI 2011 DS 4.3 CO2 Blowback Airsoft Pistol do in my testing? Not bad! Starting with the velocity fps test I shot 5 rounds through my chronograph with a brand new 12 gram CO2 cartridge and while EMG claims around 400 fps, I only averaged 321 fps with my fastest shot hitting 323 fps and my slowest shot hitting 318. So relatively close in terms of fps but not close to the 400 claimed fps. Totally fine for Airsoft games, perhaps in super hot temperatures, it can do better but in standard room temperatures this is what I got.
Next up I tested out the EMG SAI 2011 DS 4.3 CO2 Blowback Airsoft Pistol’s accuracy from 30 feet away and put 10 rounds down range as best as I was able to do with my slightly aging eyes. I was happy with the results with most of the rounds staying within about 2 inches of each other and just slightly to the right of the bullseye, but pretty much perfect in terms of elevation. There where a couple of rounds that came outside of the base 2 inch grouping, which increased the grouping to about 3 inches total.
I am a huge 1911 fan and so a 2011 design only tuns up the dial that much more. The EMG SAI 2011 DS 4.3 CO2 Blowback Airsoft Pistol performed without a glitch for me and I love the extra heft and snappy blowback action along with the crips light and short single action 1911 trigger. I was a bit surprised by the lower 323 fps velocity, but to be honest this is more than a capable velocity for a combat close range Airsoft Pistol. The EMG SAI 2011 DS 4.3 CO2 Blowback Airsoft Pistol is a real looker for sure, it just needs that eye soar of an orange tip removed to perfect its look. If you like the look and feel of a 1911/2011 in your hand, and if stainless steel is your color of choice, then I would say go for this one.
Trigger Pull: The trigger pull on the Barra 1866 Lever Action 22 Cal CO2 Pellet Rifle is light short and crips with just a little bit of take-up before it releases. You will have to first either work the lever action which also chambers a preloaded shell into the breach of the barrel, or you will have to pull the hammer back in order for the trigger to be active as a single action trigger.
Accuracy: At this time I have not made my Field Test Shooting Video or shot the Barra 1866 Lever Action 22 Cal CO2 Pellet Rifle. I am really looking forward to testing it out when I make my Filed Test Shooting Video Review for it hopefully soon! Barra claims is will shoot .22 caliber pellets up to 410 fps. I am not sure if this is for mid grain or light grain pellets but we will find out again when I make my shooting review video. The rear sight does have three positions of elevation so I should be able to find one that works here my Indoor Sea Can Airgun range where I setup paper targets at 30 feet away. I am hoping the Barra 1866 Lever Action 22 Cal CO2 Pellet Rifle shoots close to the bullseye out of the box as it does not have any windage adjustment to space of.
Build Quality: The Barra 1866 Lever Action 22 Cal CO2 Pellet Rifle seems to very well built and has a lot theft to it weighing in at 6.5 pounds so it feel very solid to hold and shoulder. It is mostly all metal which from what I can see, only the stock is plastic rather than actual wood. The faux wood does look very real and unless you get in close to it and notice none of the real wood imperfection, then you can figure out it is emotion wood. The fit and finish is all quality and I expect the Barra 1866 Lever Action 22 Cal CO2 Pellet Rifle to perform reliably.
Realism: The Barra 1866 Lever Action 22 Cal CO2 Pellet Rifle is based on the Winchester 1866 Lever Action Rifle and does look the part with all the expected working parts found on a lever action rifle. Barra has included a thumb safety behind the hammer along with a grip safety that requires the shooter to hold the lever tight to the stock or you will not be able to pull the trigger. Being a shell loading design that requires preloading pellets into the shells and then loading those shells into the rifle tub magazine also makes the experience feel very real. Barra has done a great job hiding the CO2 being the butt plate and the barrel open is about the diameter of a 45 caliber bullet.
Pros:
Not many rifles come in .22 Caliber. Should have a bit more down range power over .177 caliber.
Almost all metal construction with good weight and feel to it.
The Faux Wood stock looks very realistic, hard to tell it’s plastic!
Octagonal recessed barrel adds to realism.
White writing is mostly under the barrel so fairly discreet.
The gold receiver and but plate add to the look of quality.
Rear sight has three positions for different ranges and sighting types (standard low, peep mid, high distance).
Also have the option of mounting a red dot or magnified optical sight on the rear compact picatinny rail.
Dual 12 gram CO2 system is less expensive and reduces the cool down effect while allowing for lots of pellet reloads between heaving to change the CO2.
Has a secondary safety on the lever, it must be pressed into the stock to shoot, kind of like a grip safety.
Claimed 410 fps should be more than sufficient for mid range shooting.
Lever action rifles are just so much fun to shoot!
Cons:
Rear sight is not adjustable for windage.
More than likely going to lose some shells if you are shooting outside in the yard as they all eject into the grass or who knows where? Will probably need to buy some backup shells over time.
You will have to hold the lever snug to the stock or the trigger will not work.
Comments:
I was super excited this year at SHOT Show when I went to the Barra Booth and the Barra Team showed me their new Barra 1866 Lever Action 22 Cal CO2 Pellet Rifle. We also spoke about how the .22 caliber version shoudl be Canada friendly as it was under 500 fps. Here we now and I finally got my hands on one and it is nice to have a .22 Caliber Replica CO2 Lever Action Rifle available to us Airgun Collectors. Sure Umarex has their Legends CO2 Shell Loading BB Rifle but I like The Barra 1866 shooting pellets over BB’s. Price point for the Barra 1866 Lever Action 22 Cal CO2 Pellet Rifle is very reasonable for what you get as it is a lot of gun for the money. I am really looking forward to seeing how well it shoots and if it can get close to the claimed 400 fps.
My Vimeo Table Top Review for the Barra 1866 Lever Action 22 Cal CO2 Pellet Rifle:
Here we go with another unboxing video this month, and this is a big box, so no doubt the mystery items are going to be big too! As always with new products, I will be following up with dedicated Table Top and Field Test Videos for each of them so make sure to check down the road for those videos for a lot more information and actual performance results…
Don’t look below if you want to just watch the video and be surprises by what’s inside the mystery box but if you want a quick peak before hand then checkout the basic specs below for all three new items I will be reviewing soon.
Type: GBB Airsoft Pistol. Manufacturer: Distributed by EMG. Model:SAI 2011 DS 4.3. Materials: Mostly metal (Aluminum) and plastic. Weight: 1.94 pounds (878 grams). Total Length: 8.25 inches (210mm). Barrel: 4 inches (102mm) metal rifled. Propulsion: CO2 x1. Action: Semi auto Blowback, SAO trigger. Ammunition Type: 6mm Airsoft BB’s. Ammunition Capacity: 30+1. FPS: Claimed 380-430.
Trigger Pull: The trigger pull on the EMG SAI 2011 DS 4.3 CO2 Blowback Airsoft Pistol like what you would find on a traditional 1911 style pistol so it is Single Action Only and is nice and short and light in weight. Being a single action pistol for your first shot you will need to pull back the slide to chamber a round into the barrel which will also cock the hammer for you. the blowback action will cycle the slide for you from that point on automating the action.
Accuracy: I have not made my Field test Shooting Video or even tested out the EMG SAI 2011 DS 4.3 CO2 Blowback Airsoft Pistol yet or even shot it at all so I can not comment on the performance other than the claimed velocity of (380-430 fps) which does seem a bit high to me? My plan is to have this info available next week when I make my Field test Shooting Video so stay posted of that video coming out shortly…
Build Quality: The EMG SAI 2011 DS 4.3 CO2 Blowback Airsoft Pistol is a well made Airsoft Pistol with quality materials throughout. You will find a machined aluminum slide an aluminum frame and a full metal drop out magazine. The barrel is Titanium Nitride Coated and the only real plastic parts I could find would be the grips, the gas tube and the hop-up wheel. The stainless coating on this Airsoft pistol looks fairly thick and so should stand up over time with less wear showing.
Realism: The EMG SAI 2011 DS 4.3 CO2 Blowback Airsoft Pistol to me is not a true 2011 design as it does not have the once piece grip/trigger guard design found in 2011 pistols. It is double stack so that fits with the naming convention but I would say it is more like a combination of the Salient Arms SAI Red and SAI Red H. It does check all the boxes for realism in terms of function, looks and feel with all the working parts you expect on a Replica Airsoft Pistol including being able to fully field strip it.
Pros:
Superior Performance and 1:1 Scale Functionality.
Machined Aluminum Alloy Frame and Slide.
Rugged Reliability without sacrificing Weight.
Officially licensed by Salient Arms International.
Front and Rear Combat Style Sights with integrated Forward Fiber Optic.
Machined Anti-Glare Slide Top.
Ambidextrous Safety and Squared Trigger.
Titanium Nitride Style SAI Barrel for added durability.
On-Frame Integrated Accessory Rail.
Skeletonized trigger and hammer.
Options of both Green Gas and CO2 Magazines.
Deep Engraving with Real Steel Training Weapon Grade External Finish, Look, and Feel.
Cons:
Has orange barrel tip. But can be removed with some work.
No white dot or fiber optics on rear sight.
Not really a True 2011 in design as the name suggests.
Comments:
I am a huge 1911/2011 fan and so the EMG SAI 2011 DS 4.3 CO2 Blowback Airsoft Pistol really appeals to me. I like the compact design of the EMG SAI 2011 DS 4.3 yet it has a nice high capacity double stack magazine that gives this Airsoft Pistol a bit more girth in the hands which for me is OK as I have pretty large hands. I like that you have the option of shooting CO2 or Green Gas depending on what magazine you are using. This version comes with a CO2 Magazine, but you can purchase a green gas magazine if you prefer using gas over CO2. I like the modern look with the gold barrel and skeletonized trigger and hammer. The price is on the higher side but sometimes you have to pay a little bit more to get the additional quality and to have a gun that really stands out.
In this Mystery Boxing Video I get to take a look at 4 new Airgun Products and give you my first impressions along with a few specifications about each of them but not in a lot of details as I have not had an opportunity to research any of them as this my first time seeing them.
First out of the Mystery box is a new Umarex T4E .43 Caliber CO2 Blowback Paintball Pistol with Walther licensing called the Umarex T4E PDP. I have reviewed similar styled T4E .43 caliber CO2 Blowback Pistols in the past and this one should perform and function similarly.
The next Airgun I pulled out out of the box was the EMG SAI 2011 DS 4.3 CO2 Blowback Airsoft Pistol, a really nice 1911 styled Airsoft Pistol with a stainless finish and gold barrel with a CO2 Magazine. This one looks and feels really nice.
Staying with the pistols that came in this Mystery Box, I got my first look at the Umarex Markpoint .177 Caliber Break Barrel Pellet Pistol that has a bit of a utilitarian look and feel to it. This one is the longer barrel version and has a claimed fps of 395 using alloy pellets so we will see what it can get with more traditional lead pellets when I make my Field Test Video for it down the road a bit.
The last item out of the Mystery Box was another Umarex product, a fun CO2 BB Rifle with H&K licensing called the HK416. This semi auto and 6 round Burst internal Blowback CO2 BB Rifle is a lot like the Steel Storm and Steel Strike from Umarex but a little bit larger I would say and with H&K Licensing so more of a true Replica Airgun.
I will be making full Table Top and Field Test Videos for all of these items shortly so keep an eye out for those videos but for now you can at least get an idea what these Airgun Products will offer.
Here is video three in my series of Full Auto Fun videos I make each summer where I pick a few Full Auto Airguns and record some fun outside shooting with them. In this years Full Auto Fun Video series I do a bit of a walk around on my property and shoot a bunch of water filled pop cans. Maybe this doesn’t sound super exciting but I do use some really creative camera angles to capture it all which makes it lot more interesting to watch for sure!
In this third Full Auto Fun video I test out the Crosman A4-P AR Pistol and like my other videos it was not “picture perfect” or should I say “Video Perfect”… My cameras actually cooperated pretty good this time around, but one of my magazines had an issue (May have been me), so I had to switch over to my trusty KWA 1911 CO2 Blowback BB pistol to finish the job, good ting I had it on me, got to expect the unexpected!
Here is video two in my series of Full Auto Fun videos I make each summer where I pick a few Full Auto Airguns and record some fun outside shooting with them. In this years Full Auto Fun Video series I do a bit of a walk around on my property and shoot a bunch of water filled pop cans. Maybe this doesn’t sound super exciting but I do use some really creative camera angles to capture it all which makes it lot more interesting to watch for sure!
In this second Full Auto Fun video I test out the classic KWA Mini UZI Blowback CO2 4.5mm BB Machine Gun, at least with this video I did actually shoot in full auto but the video did not go without a few hiccups as my HoverAir Drone decided I was stopping for too long to take my shots and turned itself off a couple of times. And my Meta Glasses decided to get chunky on me and lower their frame rate down to a rather hard to watch frame per second. I did eventually make it though this video but it cold have gone better. No I am not redoing this one as it was shot in Full Auto this time which is what I promised. I can not promise all my tech gear will cooperate exactly s expected but I was able to get some decent footage overall if you can ignore the choppy video for the Meta Glasses for part of the video.
I try to make at least one series of Full Auto Fun video each summer where I pick a few Full Auto Airguns and record some fun outside shooting with them. In this years Full Auto Fun Video series I do a bit of a walk around on my property and shoot a bunch of water filled pop cans. Maybe this doesn’t sound super exciting but I do use some really creative camera angles to capture it all which makes it lot more interesting to watch for sure!
In this first Full Auto Fun video I start with the Barra 400e 4.5mm BB AEG Full Auto BB Rifle, but in the all the camera and audio setup confusion, I forgot to put it in Full Auto (getting old), so this is really not a Full Auto Fun Video, it was still fun and I hope you enjoy it anyway. The other videos in this Full Auto Fun Series are for sure in Full Auto and I will be taking out the Barra 400e and give it another go in Full Auto this time so stay posted for the true Full Auto Fun Video for the Barra 400e shortly!
In this performance Field Test Shooting Video for the John Wayne Marshal CO2 BB Revolver, I test out what the fps velocity is using a fresh standard 12 gram CO2 cartridge and shooting 4.5mm Steel BB’s through my Chronograph. I then setup a paper target 30 feet down range and shoot 10 rounds into it using the Single Action Only Trigger to see how tight of a grouping I can get out of the box. If you have not already watched my Table Top Video Review for the John Wayne Marshal CO2 BB Revolver, then make sure to do so for details and specifications along with some nice close up video.
First up for my velocity fps test of the John Wayne Marshal CO2 BB Revolver, I shot 5 rounds through my Chronograph. The slowest fps was 354 and the fastest shot hit an fps of 368, this result averaged 358 fps which was a somewhat under the claimed “up to” 420 fps from AirVenturi, still an OK velocity for shooting pop cans and the likes up to 30-40 feet away. The temperature in the Sea Can was about 20 degrees Celsius which is around 68 degrees Fahrenheit, so a good temperature to get middle of the road performance from a CO2 Airgun like the John Wayne Marshal CO2 BB Revolver. In warmer temperatures you can expect higher velocities…
I then placed my paper target on my pellet trap 30 feet downrange and using my standard semi rested shooting position (hands rested on a sandbag up front and sitting on a stool in the back), I proceeded to shoot 10 rounds into the target with the John Wayne Marshal CO2 BB Revolver and I was able to get about a 4 inch grouping well centered up and down but pushed to the left about 3 inches. I am not sure why this shot grouping spread out so much for me as my Crosman Forty Filed Test Review gave me a much better grouping and these guns are literally the same gun with different branding being the only real differences. Maybe I was just off on this day? Hey it happens sometimes!
The John Wayne Marshal CO2 BB Revolver is a lower cost mostly plastic Single Action Army Revolver with a fair amount of plastic in the build, but it does feel fairly well built and fairly solid other than being a bit lighter weight. It should produce close to 400 fps velocities in warmer conditions which is more than enough for plinking and pop can shooting which is really what it is built for. I do have to mention that this John Wayne Marshal CO2 BB Revolver for whatever reason is double the price of the Crosman Fortify CO2 BB Revolver I reviewed earlier, so if you don’t care about the John Wayne Licensing, than maybe consider the Crosman version for a lower priced option.
In this Filed Test Shooting Video recorded in the Replica Airguns Indoor Sea Can Shooting Range, I test out the Gamo GP-20 Combat CO2 BB Pistol to see what the actual velocity is in fps shooting 4.5mm steel BB’s with a fresh CO2 Cartridge. I also shoot 10 rounds of BB’s into a paper target setup 30 feet down range to see just how accurate the accurate the Gamo GP-20 Combat Pistol is out of the box. If you are more interested in details and specifications along with some closer up video of the Gamo GP-20 Combat CO2 BB Pistol, then make sure to watch my Table Top Video for it located here.
So let’s get to the velocity test for the Gamo GP-20 Combat CO2 BB Pistol. Gamo does claim up to 400 fps and to find out if these claims are true, I first installed a brand new 12 gram CO2 cartridge in the Gamo GP-20 Combat CO2 BB Pistol and proceeded to shoot 5 rounds through my Chronograph. I then averaged the shots out and was impressed with a much higher than claimed velocity of 422 fps. My slowest recorded shot was 419 fps with the fastest shot hitting 424 fps, so all of them very close to each other.
Moving on to the accuracy portion of my Field Test, I then setup a brand new paper target 30 feet away and using a semi rested shooting position (Hands on a sand bag up front and sitting on a stool in the back), I purposely shot 10 rounds with care into the target. The Gamo GP-20 Combat CO2 BB Pistol does not have adjustable sights at all so you will have to adjust your aim point if it is not bang on out of the box for you. That said, for me I was able to get about a 3 inch 10 round shot grouping, fairly well centered but just a bit to the left, about an inch or so. The shots did spread out a bit more up and down with less of a spread left to right, but still a decent grouping none the less.
The Gamo GP-20 Combat CO2 BB Pistol is like many of these low cost CO2 NBB BB Pistols, was very predictable as I have shot a ton of them and since they all share similar mechanical attributes internally, they tend to shoot about the same. I don’t mean this as a bad thing since they generally all shoot fairly decent with right around 400 fps velocities and generally I get anywhere from a 2 inch to 4 inch grouping with them. The good parts is the design is tried and trued and seems to be very durable and problem free with less moving parts to go wrong. They are also rather low cost and the magazines are interchangeable, so if you have other models based on this same build design, then you can mix and mach your magazines and load them all up for non-stop shooting fun. I do like the overall feel of this NBB CO2 BB Pistol, and the sights are very easy to aim with being white dot in the front and fiber optic in the back. If you are looking for a low cost basic NBB CO2 BB Shooter then this could just check all those boxes for you.
Type: BB Pistol. Manufacturer: Distributed by AirVenturi. Model: John Wayne Marshal. Materials: Mostly plastic, some internal metal parts. Weight: 1 pound (455 grams). Total Length: 10.5 inches (26.6cm). Barrel: 5.55 inches 14cm) metal non-rifled. Propulsion: CO2. Action: Revolver SAO. Ammunition Type: 4.5mm Steel BB’s. Ammunition Capacity: 18 round internal magazine. FPS: Claimed 420.
Trigger Pull: The trigger pull on the John Wayne Marshal CO2 BB Revolver is a single action only trigger, so you will have to cock the hammer back with each shot which does take away most of the trigger pull length and weight, making the Marshal trigger short and light and easy to shoot. Ideal for slowed down accurate shot placement, but less effective as an action shooter unless you have a very quick thumb!
Accuracy: I have not tested out the John Wayne Marshal CO2 BB Revolver but it should perform exactly like the Crosman Fortify revolver as they are literally the exact same gun with the exception of the branding and licensing. In my Field Test Shooting Review for the Crosman Fortify CO2 BB Revolver it did shoot a little bit lower than the claimed 420 fps and shot around a 2 inch 10 shot grouping at a target setup 30 feet away. You can watch that video here but I will be making a dedicated Field Test Shooting Video for the John Wayne Marshal CO2 BB Revolver shortly…
Build Quality: When it comes to the build for the John Wayne Marshal CO2 BB Revolver, there is not a lot to get overly excited about. It is basically a mostly all plastic gun with some metal parts internally like the barrel, trigger, hammer and CO2 area. The John Wayne Marshal has that lower cost Airgun, two halves, screwed together build which generally looks better on the side without the screws showing. As it is mostly plastic it is on the light side at around just over a pound. Overall there are not a lot of moving parts so it should be reliable enough just for that reason alone. All the mechanical components do what they need to do and feel solid enough.
Realism: The John Wayne Marshal CO2 BB Revolver at a glance looks a lot like a Colt Single Action Army Revolver, it has the same shape and size but the weight is much less at about half. The lack of actual bullet holes in the cylinder looking from the front of the revolver does take away from its realism. I guess I am really used to the new generation revolvers with working cylinders and real loadable and removable shells, but these guns are more expensive and hold less ammo as they are genuine to the 6 shooter capacity.
Pros:
A decent looking replica of a Colt Single Action Army revolver.
Single action only trigger is short and light and well suited to careful shot placement shooting.
420 claimed fps is about perfect for plinking at ranges up 30-40 feet.
18 round magazine has a nice high capacity and easy to load when empty
Safety is well thought out and built into an already existing part of the gun rather than simply adding a switch afterwards.
I like the look with the all back frame and bone white grips.
CO2 Allen key is built into grip so you always have it on hand and will not lose it.
John Wayne licensed for those old west John Wayne fans.
Cons:
Mostly plastic builds makes it a bit light in the hand.
No fake shell holes in the front of the cylinder, could have added this for a more genuine look.
Twice the price of the Crosman Fortify which is basically the same Airgun.
Comments: The John Wayne Marshal CO2 BB Revolver is for sure an option if you are looking for an old west single action cowboy BB shooter and specifically if you are a John Wayne fan. If you don't care about the John Wayne licensing and want to save about half of the price then my recommendation is to go for the Crosman Fortify as it is the same exact CO2 BB Revolver at the end of the day minus the john Wayne licensing on it. You also have the option of buying one of the many Shell Loading Single Action Army Revolvers available but they are a bit more money and will shoot a little slower with less ammo capacity but the trade of is a lot more realism.
Type: NBB CO2 BB Pistol. Manufacturer: Distributed by Gamo. Model: P-20. Materials: Plastic & metal. Weight: .97 pounds (439 grams). Total Length: 7.25 inches (184mm) Barrel: 4.25 inches (108mm) metal non-rifled. Propulsion: CO2 x 1. Action: Semi auto NBB, double action only trigger. AmmunitionType: 4.5mm steel BB's. AmmunitionCapacity: 20 round metal stick magazine. FPS: Claimed 400.
Trigger Pull: The trigger pull on the Gamo GP-20 Combat CO2 BB Pistol is the same as pretty much all of the DOA trigger low cost BB Pistols where the trigger has to do all the work. Much of which is pulling back the fairly strong internal hammer spring which in this case is the barrel which protrudes slightly out of the front of the pistol until you reach the release point, and it snaps back hitting the valve and pressurizing the Airgun. This will give you a bit of a finger workout if you are shooting fast and want to empty out the 20 round magazine.
Accuracy: At this point I have not tested or shot the Gamo GP-20 Combat CO2 BB Pistol but I plan on making my Field Test Shooting Video the following week so stay posted for that. I do expect it to perform nearly exactly live every other Airgun made like this, and there are many that essentially have all the same internal components with a slightly redesigned outer shell, so mechanically they are all the same and should shoot about the same. It should get really close to the claimed 400 fps and I expect it to shoot under a 2-3 inch grouping, unless I am having an off day.
Build Quality: The build quality of the Gamo GP-20 Combat CO2 BB Pistol is what you expect from almost all plastic BB Guns of this type. It is not super heavy but that means less can break when dropped on a hard surface. Fit and finish are good and one gripe I have with most of these types of BB pistols built the same way, is that the grips are a bit lose so it can pop off when you pull it back. The Gamo GP-20 Combat’s grips are a lot more solid and this does help make the Airgun feel a bit more confidence inspiring.
Realism: The Gamo GP-20 Combat CO2 BB Pistol from what I can see is not an exact copy of a real steel pistol in production but it does look like a modern semi auto pistol in design. The barrel is slightly recessed, and the CO2 tab is also hidden inside the grips, so unless you get close to the pistol you would think it could be the real deal. That said some giveaways are the moulded into the slide ejection port and the screw holes on the right side of the two plastic halves of the Airgun along with the kind of out of place standard safety switch that looks more like something you would find on a piece of electronics.
Pros:
Very low cost and simple design will make it reliable.
Fit and finish looks decent for an all plastic gun, grip are actually pretty tight.
Picatinny rail for adding accessories like a laser or tac light.
Standard metal stick magazine found in lots of Airguns for cross compatibility.
Right hand screws are very small and less obvious then some other two sided low cost plastic Airguns.
White dot sight up front and fiber optic in the back are easy to see on all backgrounds..
Safety is right above the trigger finger so easy to switch if you are right handed.
Recessed barrel for added realism.
Cons:
Some more metal would have been nice, but typical of a low cost BB shooter like this.
Double action trigger does require some work, so action shooting will be a bit harder.
Not a lot of working parts other than the trigger, safety, and magazine release.
Comments:
I have reviewed many CO2 BB Pistols built exactly like the Gamo GP-20 Combat CO2 BB Pistol, so it is at least for me, not the most exciting Airgun review but I always enjoy the chance to shoot even the most basic of Airguns. I would say the Gamo GP-20 Combat CO2 BB Pistol in this category is one of the nicer options as I feel Gamo stepped up the build quality just a bit, even if it was just to make the grips feel more solid and less prone to popping off when loading CO2. It is a little bit beefier than similar CO2 BB Pistols in this category so maybe not the best for smaller handed individuals but good for someone like me with larger mitts. The price is right for sure and with its simple design, it should perform as expected for a good long time!
Another box showed up at my door and this time I had no idea what was inside it, I asked the boys in the warehouse to surprise me and send some new product as I was low on review items, and in a couple of days later this tall somewhat large box showed up. In this Replica Airguns June Mystery Box Unboxing Video I open the box and take a look at what’s inside. I recommend you just watch the video and enjoy the suspense with me, but if you want to cheat and find out now, then look below at quick breakdown of each item…
