In this video I show you four Premium AEG Airsoft Rifles made by VFC and distributed and H&K Licensed by Umarex. This is not a detailed review but rather I focus on the basic specification and show my reaction as I take my first look at all four Umarex H&K AEG Airsoft Rifles. I do show off some close up photos so you can get an idea on the finish and what some of the components look like.
For this Field Test Shooting Video I put the Specna Arms RRA SA-C10 Core and Specna Arms RRA SA-E10 Edge head to head to see just how they will compare in terms of FPS and Accuracy at least out to 30 feet. If you want to know more about each of these AEG Specna Arms Airsoft Rifles then checkout my Table Top Review where I show them up nice and close and also talk about their specifications and how they both compare to each other.
For my Chronograph test, I decided to go with .25 gram Airsoft BB’s, a little bit heavier than what was used for the claimed FPS of around 380 using the M120 spring which by the way is preinstalled in these guns for import into Canada. Both the Specna Arms RRA SA-C10 Core and E10 Edge shot pretty similar with the C10 Core averaging right around 300 FPS and the E10 Edge shooting a little bit faster with 318 FPS. Throw some lighter .20 gram Airsoft BB’s into the mix and these numbers would go up for sure. I was using the same 11.1 volt Li-Po battery for all of my testing in this video.
Next I placed a fresh paper target 30 feet downrange and placed 10 semi auto rounds into it using a seated and rested shooting position. Both Specna Arms AEG Airsoft Rifles shot about a 1 inch grouping. I did find with both of these Specna Arms rifles that when using the peep sight they shot too low and when using the top notch sight they shot too high at least at this distance. Of course the sights are fully adjustable so this can easily be taken care of and you can adjust the hop-up for even more elevation considerations. After my 10 shot semi auto test I placed both Specna Arms Airsoft rifles in Full Auto and let the paper have it! As expected the groupings did spread out a little bit but not all that much, perhaps opening up to around 3-4 inches.
After testing both the Specna Arms RRA SA-C10 Core and E10 Edge AEG Airsoft Rifles side by side you really can’t go wrong with either version as they performed very similarly on the Chronograph and on Target. If you can afford to pay the little bit more than I would go with an Edge Series Specna Arms product since you do get a lot of extras for the little bit more you pay. Well worth it!
Type: AEG Airsoft Rifles
Manufacturer: Specna Arms.
Model: RRA SA-C10 / RRA SA-E10
Materials: Fiberglass reenforced plastic and metal/aluminum.
Weight: C10 4.9 pounds ( 2.2 kg) - E10 5.1 pounds (2.3 kg).
Total Length: 21.7 - 25.2 inches (550 - 640mm).
Barrel: 6.7 inch (170mm) inner 6.03mm tight bore barrel non rifled.
Propulsion: AEG.
Action: Single action semi & full auto.
Ammunition Type: .6mm plastic Airsoft BB’s.
Ammunition Capacity: Mid cap 120 round magazines.
FPS: 375 - 390 fps with installed spring, included M90 spring will be lower fps.
Trigger Pull: The trigger pull on both of the Specna Arms RRA SA-C10 Core and E10 Edge AEG Airsoft Rifles is similar to a light single action trigger as they are essentially an electrical on off switch. There is a little bit of take up with virtually no extra friction to let you know when the release is going to be, with a bit of use you will figure out exactly when the trigger will release the action.
Accuracy: At this time I have not made my Field Test Shooting Video or even shot the Specna Arms RRA SA-C10 Core and E10 Edge AEG Airsoft Rifles, but plan to very soon. They are next on my list for Filed Test Shooting Videos so stay posted for that video coming out soon. I do expect them to perform well and will be shooting both of these models side by side to see if there is any noticeable difference between the lower cost Core versus the slightly more premium Edge Specna Arms versions.
Build Quality: One thing I can say is no matter which version of the Specna Arms AEG Air Rifles you deicide to go with (either a Core or Edge Series), you are getting extremely good value for your money and neither one is going to have any low quality parts in it. Even the lower cost Core Series will have fiber glass reenforced plastic and metal parts along with a metal gearbox and virtually almost the same build as the more premium and slightly higher priced Edge Series. You will get upgrades in the Edge Series such as a an aluminum receiver and buffer tube, a GATE X-ASR Mosfet, the New Orion Gearbox, deep laser engraved licensing and an additional magazine. All of this for the little bit more you pay for an Edge series Specna Arms AEG Airsoft rifle.
Realism: The Specna Arms RRA SA-C10 Core and E10 Edge AEG Airsoft Rifles are based on the AR15 or M16 platform of course in a very modern and PDW styled look. They look and feel the part for sure with lots of working parts including the safety, selector switch, charging handle, dust cover, adjustable rear stock, pop-up front and rear sights as you would expect. Most of the hardware should be interchangeable with a real steel AR if you want to personalize the look of your Specna Arms Rifle.
Pros:
Super affordable yet very high quality product for what you pay.
Two options to consider, both with good price points and value.
Quality components throughout both the Core and Edge series.
Rock River Arms Licensed with hologram on receiver.
ESA™ quick spring change system makes spring changes quick and easy.
Comes with two springs for potential indoor and outdoor usage.
Plastic parts are fiberglass reenforced making them very durable.
Quick release fully adjustable pop-up sights.
No orange tips on our Canada Store versions.
Lots of rial mounting options even on such short PDW styled AR’s.
Metal gearboxes with metal gears and mostly all metal parts inside.
Easy access to motor for any possible trouble shooting you may need to do.
Cons:
Popup sights are mostly plastic..
Need to hold back charging handle to access the hop-up wheel.
Comments:
Value for your money is what comes to mind when I think about the entire Specna Ams AEG Airsoft Riffle product line. And this goes for not only the lower priced Core Series but also the premium Edge Series. Both version are built supper tuff with quality components throughout. You are just getting upgrades you are probably going to do at some point in time with the Edge Series and of course more metal components when you spend about $100 more for a similar Edge version. I figure if you can muster up the extra cash then go with an Edge Specna Arms AEG Airsoft Rifle, that said, any of the Core models will be money well spent.
Make sure not also watch my previous Specna Arms YouTube Video where I introduce the product line, show you around several models and talk about the key differences between the Core and Edge versions.
My Vimeo Table Top Review for the Specna Arms RRA C10 Core & E10 Edge Airsoft Rifles:
We have a new line of Airsoft rifles from Specna Arms I am super happy to be introducing to the Replica Airguns Airsoft Community.
Specna Arms AEG Airsoft Rifles are extremely cost effective and offer value for what you pay that is amazing. In this YouTube Introduction Video I go over the main differences between the Core Series (lower priced) versus the Edge Series (mid priced) so that you can understand what the extra cost will get you when buying a Spenca Arms Edge Series AEG Airsoft Rifle over a Specna Arm Core Series AEG Airsoft Rifle.
I also show 12 different versions from the Specna Arms Core and Edge Series some with Rock River Arms licensing and some without.
Specna Arms Core Series
Price: Mid $200’s (CAD)
Materials: Fiberglass Reenforced Plastic & Metal
Mosfet System: No
Gear Box: Ver 2 Metal Fully Upgradeable
Spring System: ESA Quick Change - 2 Springs (380-310 fps)
Licensing: Rock River Arms Some Models
Magazine/s: Comes with 1 Mag
Specna Arms Edge Series
Price: Mid-high $300’s (CAD)
Materials: Aluminum & Fiberglass Reenforced Plastic
Mosfet System: GATE X-ASR
Gear Box: Ver 2 - Orion Gear Box, Reenforced Shell & Internals
Spring System: ESA Quick Change - 2 Springs (380-310 fps)
Licensing: Rock River Arms Some Models
Magazine/s: Comes with 2 Mags
Type: Airsoft Sniper Rifle
Manufacturer: Tokyo Marui.
Model: VSR-10 Pro
Materials: ABS and Metal.
Weight: 4.6 pounds (2090 grams).
Total Length: 42.3 inches (107.5 cm)
Barrel: 17 inches (43 cm), metal non-rifled.
Propulsion: Spring.
Action: Bolt.
Ammunition Type: 6mm Airsoft BB's.
Ammunition Capacity: 30 round magazine.
FPS: 366.
Trigger Pull: The trigger pull on Tokyo Marui VSR-10 Pro Sniper Spring Bolt Action Airsoft Rifle is nice and short and light as would be expected form a bolt action sniper rifle. The take-up and release are virtually on existent, just nudge your finger a bit and this Airsoft rifle is firing a round down range.
Accuracy: So far I have not tested out the Tokyo Marui VSR-10 Pro Sniper Spring Bolt Action Airsoft Rifle but from what I have seen watching other YouTube videos, it looks to be very accurate right out of the box. The version I have has the Canada import legal heavier spring so it should shout right around 366 fps or a tad higher using .20 gram Airsoft BB’s. I will probably test mine out using heavier Airsoft BB’s when I perform my Field Test Shooting Video for the Tokyo Marui VSR-10 Pro Sniper Spring Bolt Action Airsoft Rifle.
Build Quality: The Tokyo Marui VSR-10 Pro Sniper Spring Bolt Action Airsoft Rifle like all Tokyo Marui products is very well made, there is a lot of plastic in this Airsoft Sniper rifle but it is of good quality, you will find metal in the barrel and bolt areas of course. The trigger, safety and sling attachments are also metal.
Realism: The Tokyo Marui VSR-10 Pro Sniper Spring Bolt Action Airsoft Rifle is based off of your typical bolt action hunting rifle with not a lot fo bells and whistles other than the included adjustable open sights but you can pimp it out with a ton of aftermarket modifications including much suppresses, scope mounts for a scope, bipods and pretty much all the internal parts can be upgraded and swapped out.
Pros:
Not a clone so all aftermarket parts will work on and in it.
No CO2 or batteries required, ready when you are.
Expect excellent accuracy at most ranges.
Easy to adjust on the field Hop-up.
Super easy to operate bolt action and very nice trigger.
Comes with heavier spring installed so more powerful than standard version.
Comes with integrated fully adjustable sights, no need for a scope to start shooting.
Comes with sling mounts which make it Bipod compatible.
No red tip.
Cons:
Does not come with scope plate so you will need that if you plan to install a stope on it.
Front sight is taped on with double sided tape.
Cost is high compared to other Spring powered Airsoft rifles on the market..
Comments:
There are lots of clones out there of the Tokyo Marui VSR-10 Pro Sniper Spring Bolt Action Airsoft Rifle but this is the real deal and so you will pay more for it for sure but you will get Tokyo Marui quality and performance. That can not be said for the clone versions. If you do plan on upgrading yours down the road the Tokyo Marui version will accept all the aftermarket add ons and parts which again the clones may not and so you could end up wasting your money on parts that don’t fit with the other versions. Something to keep in mind when adding up all the costs. One thing to be aware of with the Tokyo Marui VSR-10 Pro Sniper Spring Bolt Action Airsoft Rifle is the bolt is a bit firmer with the upgraded spring dn so you need to make sure it is all the way forward before twisting and releasing. If you don’t it will not lock into place and you will end up scratching the back paint off of the area just in front of the safety, not a big deal, you can always touch it up easy enough.
My Vimeo Table Top Review for theTokyo Marui VSR-10 Pro Sniper Spring Bolt Action Airsoft Rifle:
Perhaps you might call this a followup video since I already made a full Field Test Shooting Video of the all black version of this pistol and you may wonder if the color of a gun could in some way effect how it performs? Well I don’t think color would really matter but it has been over 6 years since I did my original Field Test Shooting video fo the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver and so perhaps some things have changed, maybe my shooting is better or worse? At any rate let’s find out.
Also make sure to take a look at my Table top Video for the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver if you're interested in the specifications and details along with some nice tight close up video of the Airgun.
Starting off with my Chronograph test I was able to get an average 6 shot velocity of 348 fps which is about 40 fps less than my testing 6 years ago of 390 fps, perhaps the temperatures where a bit different? Perhaps the valve setups of the guns was not the same? By the way the temperature was 23 degrees Celsius in the indoor Airgun Sea Can Shooting Range and I was using a brand new 12 gram CO2 along with 5.1 grain zinc coated steel BB’s.
Moving on to the accuracy test, surely I would get a similar 1 inch 6 shot grouping from the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver, after all it’s been 6 years and I must be a much more advanced shooter… Well there again the Chrome Umarex Colt Python 357 Magnum CO2 BB Revolver did not perform as well as the black one from my 2014 Field Test? Again maybe the steel BB’s I was using where not of the same quality? Maybe I simply had one too many espresso shots? As the video shows this time around I was only able to get about a 2 inch 6 shot grouping from the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver. Still not bad but I was hoping for better result or at least the same as before.
I could do this test again and get completely different results using perhaps another brand of CO2 on a warmer day with higher quality Steel BB’s and just maybe with me on my game a little bit better? At the end of the day 350 fps is perfectly fine for putting holes in pop cans and a 2 inch group at 30 feet will get you on most targets every time so I’m not going to sweat it too much. If you are looking for a shell loading CO2 BB Revolver the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver is for sure one of my top picks.
Type: BB air revolver
Manufacturer: Umarex.
Model: Colt Python 375
Materials: Almost entirely all Metal.
Weight: 2.75 pounds (1218 grams).
Barrel: 5.5 inches, metal non-rifled.
Propulsion: 12 gram CO2.
Action: Revolver, single & double actions.
Ammunition Type: 4.5mm steel BB's.
Ammunition Capacity: 6 round cylinder.
FPS: 400.
Trigger Pull: The trigger pull on the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver is good in both single and double action, it’s nice that you have the shorter lighter single action trigger for slower more accurate shooting but you can also blast away in double action when you feel like it. The hammer on the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver is firm with not very much wiggle which some other revolvers in this category do have.
Accuracy: Based on my results shooting the Umarex Colt Python 357 which is essentially the same gun in a different finish. The results I got shooting my 6 round group from a 30 foot out semi rested position where good overall. Vertically there was about a 2 inch spread while horizontally there was about a 1 inch spread. I did find the plastic tips on the brass shells seemed to be a bit tight at first and this is when I did most of my Chronograph and target shooting. I believe the tightness effected the consistency of the FPS which also effected the accuracy especially up and down. I did get one shot out of the Umarex Colt Python 357 well over the claimed 400 fps but again the fps was rather erratic most likely because of the snug BB fit due to shell break-in.
Build Quality: The Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver being mostly metal has a very good build quality and is on par with the Dan Wesson 715 shell loading revolver. It has a nice weigth adn balance to it and feels really good in the hand! The only real plastic I could find was in the grips and the shell tips. Fit and finish was also good with no noticeable chrome wear or sloppy workmanship. It will be interesting to see how the Chrome finish wears over time compared to the black finishes fodun on most KWC made Airguns.
Realism: TheUmarex Colt Python 357 Magnum Chrome CO2 BB Revolver overall is a close copy a the real steel Colt Python 357 styled revolver. I did notice the rear portion of the receiver (between the rear cylinder and hammer) to be a bit longer perhaps to accommodate the CO2 valve length, but other than that, this pistol is super close to the original Colt Python 357 styled revolver it is based on. Again being all metal gives this CO2 BB revolver very realistic weight and feel and the loadable brass shells make using this gun almost exactly like using a real shell loading revolver but for much less cost per shot and of course a lot less recoil on the hands and noise to be had.
Pros:
Shells loading revolver give you the feeling of loading and shooting a real revolver.
Mostly all metal design.
Lots of detail, well made, chrome looks nice, not sure if it will wear better than the black finish found on most KWC made pistols?
Good overall weight, almost 3 pounds.
Should have good overall power, accuracy and shots per CO2 (based on my previous Colt Python testing).
Fully adjustable sights.
Well hidden CO2 Screw.
Recessed barrel.
Nice Trigger pull in both single and double action.
Cons:
Grips are a bit rough and wood grain is only OK.
Grips may be a bit large for people with small hands.
Decent enough Colt Python 357 replica but the frame is a bit long between the cylinder and the hammer.
Comments:
It’s been a while since I reviewed a Shell Loading Airgun and this one is pretty much the same Airgun I have reviewed in the past in both the KWC and Umarex Distributed forms. It has been almost 6 years since I took a look at one on my table and it still hods up today. I plan on performing another Field Test Shooting Review for the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver to see if I can replicate the same good results I did back in 2014 when I tested it out on my deck. If you’re looking for a shell loading revolver in the 357 design then for sure checkout the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver as an option.
My Vimeo Table Top Review for the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver:
Type: Airsoft Pistol.
Manufacturer: KWC.
Model: PT92
Materials: Almost entirely all Metal.
Weight: 2.4 pounds (1089 grams).
Barrel: 4.5 inches, metal non-rifled.
Propulsion: 12 gram CO2.
Action: Semi and full auto, single and double action with full blowback.
Ammunition Type: 6mm Plastic Airsoft BB's.
Ammunition Capacity: 27 rounds full size drop out metal magazine.
FPS: 388 using .25 gram Airsoft BB’s.
Trigger Pull: The trigger pull on the KWC PT92 CO2 Blowback Airsoft Pistol is good in both single and double action. Of course in single action the trigger is much shorter and lighter but that said double action is still very usable. Once you fire a round in either double or single action the blowback action will continue to cock the hammer back allowing for single action followup shots.
Accuracy: The KWC PT92 CO2 Blowback Airsoft Pistol performed OK during my Field Test Shooting review in terms of accuracy. I shot it first in semi auto to get a sense of the overall accuracy and in terms of elevation it was right in the middle of the target. I did find the shots spread out a bit side to side perhaps as much as 4-5 inches during my test grouping. As expected when I flipped the happy switch to full auto the KWC PT92 CO2 Blowback Airsoft Pistol pretty much sprayed the target working its way up as the recoil from the full auto blowback action lifted the barrel. In terms of power the KWC PT92 CO2 Blowback Airsoft Pistol shot pretty hot, I was using .25 gram Airsoft BB’s and was still able to achieve close to 400 fps.
Build Quality: The KWC PT92 CO2 Blowback Airsoft Pistol like the other all metal KWC made Beretta 92 or Taurus PT92 copies out there being sold under different company names, is a good value blowback Beretta Taurus Airgun no matter which version you get. It’s not the best or worst, right about in the middle but most of the bugs have been worked out since it came out just after the KWC 1911 line and that’s been out for some time now. I find the finish does come off a bit easy but when this happens it kind of gives the Airgun a more realistic and slightly worn in look to it.
Realism: The KWC PT92 CO2 Blowback Airsoft Pistol is a One to One replica of the real steel Taurus PT92 and does a great job at replicating it. You would be hard pressed to see any differences in the Airgun version versus the 9mm caliber firing version until you pick one up and work the parts a bit. Even so pretty much all the mechanical parts work the same as a real steel Taurus PT92 including the ability to filed strip the Airgun version and gain access to the hop-up and other internal parts.
Pros:
All metal construction.
Full length blowback action with nice heavy recoil.
Accurate Taurus PT92 replica.
Single and double action triggers both feel good.
Double stack style metal magazine holds the CO2 and Airsoft BB’s.
No ugly white writing ( warning instructions) on the gun.
Fully filed strippable.
Adjustable Hop-up.
Recessed barrel for added realism.
FPS is fairly high for a full blowback gun.
Cons:
Finish on KWC guns can wear off quickly in the high spots but has gotten better over the years.
Full blowback action especially when in full auto mode will eat up a lot of CO2.
Comments: If you are a Beretta 92 or Taurus PT92 fan than I am sure you have already taken a look at the KWC line of Beretta 92 and Taurus PT92 Airguns, maybe in a steel BB version or Airsoft version? KWC first offered it in this PT92 style and then later brought out a more true to form Beretta 92 version. Depending on where you live and which model you buy you may or may not have the full auto feature but to be honest full auto is fun at first but then you realize you don’t really hit much with it and just end up wasting a lot fo CO2 and BB’s. Checkout our Replica Airguns Canada and US Stores for all the different versions and models of this KWC Beretta and Taurus style Airgun.
My Vimeo Video Review for the KWC PT92 CO2 Blowback Airsoft Pistol:
Type: Airsoft Pistol.
Manufacturer: KWC.
Model: M1911
Materials: Almost entirely all Metal.
Weight: 1.97 pounds (894 grams).
Barrel: 4.5 inches, metal non-rifled.
Propulsion: 12 gram CO2.
Action: Semi auto, single action only with full blowback.
Ammunition Type: 6mm Plastic Airsoft BB's.
Ammunition Capacity: 14-15 rounds full size drop out metal magazine.
FPS: 360+.
Trigger Pull: The Single Action Only trigger pull on the KWC M1911 CO2 Blowback Airsoft Pistol is exactly as it should be and just like what you would find on a real steel Colt 1911 pistol. That would be short, light and crisp. As there is no double action mode, you are required to rack the slide back to chamber a rounds and cock the hammer for the first shot, afterwards the blowback action will do this for you.
Accuracy: I wasn’t overly impressed with the accuracy of the KWC M1911 CO2 Blowback Airsoft Pistol when I tested it out in the Replica Airguns Indoor Sea Can Airgun Range but it is what it is. The M1911 shot really high and a bit loose getting about a 5 inch 10 shot grouping, perhaps a hop-up adjustment was in order but this is how it shot right out of the box which is how I test all my Airguns. In terms of power the KWC M1911 CO2 Blowback Airsoft Pistol was bang on shooting .25 gram Airsoft BB’s at right around 350 fps.
Build Quality: The KWC M1911 CO2 Blowback Airsoft Pistol like the other all metal KWC made 1911’s out there being sold under different company names, is a good value Blowback 1911 Airgun no matter which version you get. It’s not the best or worst, right about in the middle but most of the bugs have been worked out since this is one of the longes CO2 1911’s out there and for the most part has stayed about the same. I find the finish does come off a bit easy but when this happens it kind of gives the 1911 Airgun a more realistic and slightly worn in look to it.
Realism: The KWC M1911 CO2 Blowback Airsoft Pistol is a One to One replica of the real steel M1911 A1 and does a great job at replicating it. You would be hard pressed to see any differences in the Airgun version and the .45 caliber firing version until you pick one up and work the parts a bit, even so pretty much all the mechanical parts work the same as a real steel M1911 A1 including the ability to filed strip the Airgun version and gain access to the hop-up and other internal parts.
Pros:
All metal construction.
Full length blowback action with nice heavy recoil.
Accurate Colt M1911 A1 replica.
Single action only trigger feels good, short light and crips.
Accurate trigger design and working grip safety.
Metal magazine holds the CO2 and 14-15 Airsoft BB’s.
No ugly white writing (warning instructions) on the slide of the gun.
Fully filed strippable.
Adjustable Hop-up.
Recessed barrel for added realism.
FPS is just about perfect, just over 360 fps using .20 gram BB’s, not too powerful but Canada import friendly.
Cons:
Finish on KWC guns can wear off quickly in the high spots but has gotten better over the years.
Full blowback action will eat up a lot of CO2.
Comments: I have always been a fan of the 1911 pistol and the KWC M1911 CO2 Blowback Airsoft Pistol is no exception to this. Like all of the KWC 1911’s out there being redistributed by the big airgun companies the KWC version is really no different other than more simple KWC branding and with no licensing on the Airgun to speak of. Some people prefer the cleaner look to it and some will like to have licensed versions, to each their own. Do some looking around on our website and find a KWC made 1911 you like best, perhaps a simple KWC M1911 A1 like the one reviewed here or maybe a more tactical version with all the more modern updates to it like a rail, ambidextrous controls and tactical triggers and hammers.
My Vimeo Video Review for the KWC M1911 CO2 Blowback Airsoft Pistol:
If you have not already watched my Preview video for both of these Airsoft pistols then make sure to watch that video for details and specifications along with some nice tight shots of each Airsoft gun.
Another multi gun Field Test Shooting Review, in this Indoor Sea Can Field Test Shooting Video I test out the KWC M1911 and PT92 Full Blowback CO2 Airsoft Pistols. I first place 5 6mm .25 gram plastic Airsoft BB’s through my Chronograph to find out what the real world velocity is for each Airsoft Pistol and then I perform my accuracy test where I shoot multiple rounds into a paper target 30 feet down range to see how close of a grouping I can get with each Airgun. I use a seated and rested shooting position to eliminate as much human factor as possible. By the way is used a brand new 12 gram CO2 and the temperature was 25 degrees Celsius (77 degree Fahrenheit) inside the Airgun Sea Can Shooting Range.
Starting with the KWC M1911 CO2 Blowback Airsoft Pistol I averaged 351 fps with the fastest shot being 353 and the slowest shot 345, so very consistent for sure! Accuracy for the KWC M1911 CO2 Blowback Airsoft Pistol could have been a bit better, I had to adjust my aim point to just under the bottom rings and even so the KWC M1911 wanted to shoot high, I was able to get around a 5 inch 10 shot grouping but was hoping for a bit better.
Next I tested out the KWC PT92 CO2 Blowback Airsoft Pistol which does have a full auto option. For the velocity portion of my Field Test the KWC PT92 did shoot a bit after than the MWC M1911 getting an average fps of 388 with the fastest shot hitting 396 and the slowest shot at 383 so again very consistent performance. Since the KWC PT92 CO2 Blowback Airsoft Pistol is capable of full auto shooting I decided to shoot 5 rods on my paper target to get a base accuracy and this resulted in a bit of a lateral spread fairly close to the bullseye about 4-5 inches apart. I then did a mag dump and as expected pretty much sprayed 6mm Airsoft BB’s all over the place but most shot a bit high and to the left probably because of the blowback recoil action.
The KWC M1911 and PT92 CO2 Blowback Airsoft Pistols are both classic Airguns and great options if your looking for a 1911 or Beretta styled Airgun to add to your collection without all the markings and white writing on them.
You’ve seen them all before but have you seen them in this exact configuration? All the Airguns I show off in this video are made by KWC and generally come in either Steel BB and or Airsoft versions along with non-blowback and blowback versions. You can even find most of them redistributed by other companies like Umarex, Cybergun, Gletcher, Crosman and others even licensed in some cases.
The versions I am showing today I have not review yet in these exact configuration and all of them are the KWC made and distributed unlicensed versions, so nice and clean with virtually none of that ugly white lettering on them…
KWC M1911 CO2 Blowback Airsoft Pistol
Type: Airsoft Pistol
Manufacturer: KWC
Model: M1911
Materials: Full Metal
Weight: 894 g (1.97 lb)
Barrel: Smoothbore
Power Source: CO2
Action: Semi-Automatic, Single-Action
Ammo Type: 6mm Airsoft BBs
Ammo Capacity: 17 Rounds
FPS: 400 FPS
KWC PT92 CO2 Blowback Airsoft Pistol
Type: Airsoft Pistol
Manufacturer: KWC
Model: PT92
Materials: Full Metal
Weight: 1089 g (2.4 lb)
Barrel: 104 mm (4.1 in)
Power Source: CO2
Action: Semi-Automatic/Full-Automatic
Ammo Type: Sirsoft BBs 6mm
Ammo Capacity: 27 Rounds
FPS: 414
Make sure to check out my Table Top Video and Written Review for the ASG CZ P-09 Threaded Barrel CO2 Blowback Airsoft Pistol where I go over the features and specifications along with some nice close up video.
In this Field Test Shooting Video I shoot the ASG CZ P-09 Threaded Barrel CO2 Blowback Airsoft Pistol in my indoor Sea Can Airgun Shooting Range to see what the actual velocity is and also see how well it will group shooting 10 Airsoft BB’s at a paper target 30 feet down range. I was using .25 gram Airsoft BB’s for my testing purposes with Propane Gas as my propellant. The temperature inside the Sea Can was around 26 degrees Celsius (79 degrees Fahrenheit).
I started off my Field Test Shooting video with the Chronograph portion of my test and placed 5 shots through my Chrony using a brand new 12 gram CO2 cartridge. I have to mention the fps consistency was very impressive with all five shots only varying within 6 fps of each other the slowest being 330 fps and the fastest test shot being 336 fps. My end 5 shot average fps was 33fps again using a .25 gram Airsoft BB.
I then loaded my ASG CZ P-09 Threaded Barrel CO2 Blowback Airsoft Pistol with 10 rounds for the accuracy portion of my test and was able to get all 10 shots within a nice 2 inch grouping. The shot placement was well centered left to right and a little bit high on target which I am sure could be adjusted for using the hop-up.
The ASG CZ P-09 Threaded Barrel CO2 Blowback Airsoft Pistol is a rally nice Airsoft pistol, it has a great trigger with a firm blowback action. The super consistent fps is pretty much exactly where you want it to be, just powerful enough to allow for Canada import but not too powerful for Airsoft gaming. The accuracy was also very good right out of the box so pretty much nothing to complain about in terms of performance. Another nice Airsoft product from ASG!
Make sure to check out my Table Top Video and Written Review for the Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol where I go over the features and specifications along with some nice close up video.
In this Field Test Shooting Video I shoot the Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol in my indoor Sea Can Airgun Shooting Range to see what the real world velocity is and also how well it will group shooting 10 rounds at a paper target 30 feet down range. I was using .25 gram Airsoft BB’s for my testing along with Propane Gas. The temperature inside the sea can was around 26 degrees Celsius (79 degrees Fahrenheit).
Because the Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol coms with both a shorter internal barrel and a screw on extended barrel designed to be hidden inside a mock suppressor I thought it would make sense to test both the short and long barrels to see what the fps difference would be. With the short internal barrel I shot 4 rounds and average 255 fps. I then added the longer barrel extension again shooting 4 rounds but this time I averaged 363 fps so a good 100+ fps faster with the longer barrel attachment added to the Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol.
For my accuracy portion of the testing I left the extended barrel on the gun but was a bit disappointed in my 10 shot grouping. The Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol did not get the tightest of groupings coming in at around 5 inches. It also shot a little bit to the right but vertically was fairly well centered. Perhaps changing up the barrels and lengths might make a difference?
I did really like the Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol, it has a really light trigger that is a bit hard to find the release point, the blowback action is crisp but not overly heavy. I’m pretty sure the Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol is a VFC product so the quality is bang on. Other than the grouping being a little bit spread out I really liked everything about the Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol.
Type: Blowback CO2 Airsoft Pistol.
Manufacturer: ASG
Model: CZ P-09 Threaded Barrel.
Materials: Metal and polymer construction.
Weight: 2.3 Pounds (1050 grams).
Barrel Length: 4.4 inches (11.2 cm).
Total Length: 9 Inches (22.9 cm).
Propulsion: CO2
Action: Single and double action.
Ammunition Type: 6mm plastic Airsoft BB’s.
Ammunition Capacity: 25 round magazine.
Max FPS: 376 fps.
Trigger Pull: The ASG CZ P-09 Threaded Barrel CO2 Blowback Airsoft Pistol has a single and double action trigger setup. Both feel pretty decent, the double action trigger pull is a little on the heavy side but you won’t really be shooting in double action all that much since the blowback action will cock the hammer between shots allowing for the vast majority of your shots to be single action which you will find are short and very light. There is a slight bit of take-up followed by a crisp very light release.
Accuracy: So far I have not made my Field Test Shooting Video for the ASG CZ P-09 Threaded Barrel CO2 Blowback Airsoft Pistol. Check back shortly for my upcoming Field Test Shooting Video for the ASG CZ P-09 Threaded Barrel CO2 Blowback Airsoft Pistol, until then the shooting results will remain a mystery but if this product is like otter ASG products it should produce good results for me .
Build Quality: The build quality of the ASG CZ P-09 Threaded Barrel CO2 Blowback Airsoft Pistol is what I would expect from an ASG Airgun. The materials used look good and have an excellent finish to them. Slide wiggle is very minimal and all the mechanical parts feel solid and responsive. You will find metal parts where you would expect them to be like in the slide, barrel components, magazine, slide catch release take-down leaver, safety, hammer, trigger, rear sight, magazine release and lots of other internal parts.
Realism: In terms of realism the ASG CZ P-09 Threaded Barrel CO2 Blowback Airsoft Pistol is an excellent copy of the real steel CZ P-09 with all the markings and licensing in all the right places. Mechanically everything works about the same including full field strip-ability and the ability to add a mock suppressor if you want to.
Pros:
Build quality feels really goods, lots of weight to this Airsoft Pistol.
Full length blowback action.
Accurate licensed CZ P-09 replica.
Trigger pull is nice in both single and double action.
Picatinny rail for adding accessories like a tac light or laser.
Double stack full size drop out Metal Magazine holds the CO2 and 25 Airsoft BB’s
Comes with black and orange tips depending on what you prefer to use.
Easy to see white dot front and back sights.
CO2 powered makes it easy for Canada import.
Easily Filed Strippable.
Tips are easy to remove for the addition of a mock compensator.
Adjustable Hop-up.
Cons:
Sights don’t seem to be adjustable.
Controls are not all ambidextrous.
Comments:
The ASG CZ P-09 Threaded Barrel CO2 Blowback Airsoft Pistol is another great addition to the ASG CZ line of Airguns. You can now get CZ Replica Airguns from ASG in a variety of models including the CZ 75D, CZ 75 P-07 Duty, CZ 75D Compact and of course the CZ P-09 in Airsoft, Steel BB and even Pellet firing ammunition. I would say the ASG CZ P-09 Threaded Barrel CO2 Blowback Airsoft Pistol is probably one of the most realistic in terms of looks, action and functionally but no matter what your preferences is, ASG will have something for you in the CZ lineup of Airguns for sure!
My Vimeo Table Top Review for the ASG CZ P-09 Threaded Barrel CO2 Blowback Airsoft Pistol:
Type: GBB Airsoft Pistol.
Manufacturer: Cybergun
Model: FN Herstal FNX-45 Tactical.
Materials: Metal and polymer construction.
Weight: 1.8 Pound (820 grams).
Barrel Length: 4.8 inch (12.2 cm).
Total Length: 8.9 Inches (22.6 cm).
Propulsion: Green gas or propane
Action: Single and double action.
Ammunition Type: 6mm plastic Airsoft BB’s.
Ammunition Capacity: 25 round magazine.
Max FPS: 380 fps.
Trigger Pull: The Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol has a single and double action trigger setup. Both feel pretty good with a surprisingly light double action trigger pull, the blowback action will cock the hammer between shots allowing for the vast majority of your shots being single action which you will find are short and very light. There is a little bit of take-up followed by a crisp light release.
Accuracy: So far I have not made my Field Test Shooting Video for the Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol. Keep posted for my upcoming Field Test Shooting Video for the Cybergun FN Herstal FNX-45 Threaded Barrel GBB Airsoft Pistol, until then I can not really comment on the shooting results.
Build Quality: The build quality of the Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol feels really good, it has a nice weight to it and feels really solid in the hand. The materials used look good and have an excellent finish to them. There is just a bit of a slide wiggle but not excessive. You will find metal parts where you would expect them to be like in the slide, barrel components, magazine, slide catch release, take-down leaver, hammer and lots of internal parts.
Realism: In terms of realism the Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol is pretty much the spitting image of the real steel version with all the markings and licensing in all the right places. Mechanically everything works about the same including full field strip-ability with full ambidextrous controls.
Pros:
Build quality feels really good.
Full length blowback action.
Accurate licensed TFN Herstal FNX-45 Tactical replica.
Trigger pull is nice in both single and double action.
Picatinny rail for adding accessories like a tac light or laser.
Double stack full size drop out metal magazine holds the gas and 25 Airsoft BB’s
Comes with additional back-strap in smaller size for smaller hands.
White dot high rise front and back sights suitable for compensators.
Fully ambidextrous controls.
Easily Filed Strippable.
Tip is easy to remove for addition of a mock compensator.
Adjustable Bax Hop-up
Cons:
Sights are not adjustable.
Just a little bit of slide wiggle.
Comments:
The Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol is a really great looking gun. The quality is on par with KWA and KJ Works in my opinion. I’m not sure who actually makes it as Cybergun is the license holder and distributer but I feel like the Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol is a step up from the standard KWC gun often used as the base. I look forward to testing out the Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol in the Sea Can indoor Airgun Shooting range to see how it performs. I’ll be testing with the short barrel and with the barrel extension installed to see what the fps difference is between the two.
My Vimeo Table Top Review for the Cybergun FN Herstal FNX-45 Tactical GBB Airsoft Pistol:
In this Table Top Preview video I take a look at two Blowback Airsoft Pistols one Distributed by Cybergun and the otters Distributed by ASG. Both are very similar in that they have threaded barrels which makes them much suppressor ready the big difference being that the ASG CZ P-09 is CO2 powered while the FN Herstal FNX-45 is Green Gas or Propane powered. IN this video I talk about the specifications and details and also show both Airsoft Pistols up nice and close.
Cybergun FN Herstal FNX-45 Threaded Barrel GBB Airsoft Pistol
Ammo Type: 6mm Airsoft BB’s
Ammo Capacity: 25
Power Source: Green Gas
Primary Material: Metal & Polymer
Weight: 1.8 Pounds (820 grams)
FPS: 380
Total Length: 8.9 Inches (22.6 cm)
Barrel Length: 4.8 inch (12.2 cm) Threaded
Blowback Action: Full Blowback
Trigger Action: Double/Single
Hopu-up: BAX
Rear Sight: Fixed (Raised)
Front Sight: Blade (Raised)
Rail Type: Picatinny
Color: Black (also comes in tan)
Licensed FNH trademarks on slide and grip
Distributed by Cybergun made in Taiwan
ASG CZ P-09 Threaded Barrel CO2 Blowback Airsoft Pistol
Ammo Type: 6mm Airsoft BB’s
Ammo Capacity: 25
Power Source: CO2 x1
Primary Material: Metal & Polymer
Weight: 2.3 Pounds (1050 grams)
FPS: 376
Total Length: 9 Inches (22.9 cm)
Barrel Length: 14.4 inches (1.2 cm) Threaded
Blowback Action: Full Blowback
Trigger Action: Double/Single
Hop-up: Adjustable
Rear Sight: Fixed
Front Sight: Blade
Rail Type: Picatinny
Color: Flat Dark Earth (also comes in Urban Grey and all Black)
Licensed CZ trademarks on slide and grip
Distributed by ASG made in Taiwan
Type: Pellet Revolver.
Manufacturer: Gamo
Model: PR-776.
Materials: Mostly metal construction.
Weight: 2.2 Pounds (1 kg).
Barrel Length: 6 inches
Total Length: 11.5 inches.
Propulsion: CO2 x1
Action: Revolver single and double action.
Ammunition Type: .177 caliber pellets.
Ammunition Capacity: 8 rounds per magazine.
Max FPS: 400+ fps.
Trigger Pull: The Gamo PR-776 CO2 .177 Caliber Pellet Revolver has your traditional revolver single and double action trigger setup. In double action, the trigger is going to be a bit longer and heavier but it feel fairly smooth with no real friction points and I would consider it to have a medium trigger pull. When you cock the hammer back placing the Gamo PR-776 CO2 .177 Caliber Pellet Revolver in single action, the trigger pull becomes very short with virtually no take-up at all and the weight of the trigger is very light allowing for more accurate shots.
Accuracy: Make sure to watch my Field Test Shooting video for the Gamo PR-776 CO2 .177 Caliber Pellet Revolver where I test out the velocity and accuracy in the Replica Airguns Indoor Airgun Shooting Range. In summary the Gamo PR-776 CO2 .177 Caliber Pellet Revolver shot a little bit hotter than claimed at just over 400 fps using around 7 grain lead pellets. In terms of accuracy with a total of 16 shots the grouping spread out to around 4 inches but I am pretty sure a different pellet choice may have made a difference.
Build Quality: The build quality of the Gamo PR-776 CO2 .177 Caliber Pellet Revolver is pretty good overall. It is mostly all metal with the exception of the grips of course, Fit and finishes looks good, everything feel snug adn tight with the exception of the pistol grips. I feel like the grips could easily move out of place and get caught on something. This is not a problem when shooting, more so when in a holster. The Gamo PR-776 CO2 .177 Caliber Pellet Revolver feels good in the hadn't, nice and solid and with a good weight to it.
Realism: The Gamo PR-776 CO2 .177 Caliber Pellet Revolver is a decent looking Airgun in the style of a traditional revolver, I wouldn’t say it’s an exact replica of any specific revolver in production but it does tick off all the boxes in terms of looking realistic. The weight and feel for now and the Gamo PR-776 CO2 .177 Caliber Pellet Revolver also has a recessed barrel and hidden CO2 crew. The only real giveaway would be the cylinder size as it is a bit smaller than expected and of course is chambered for .177 caliber pellets.
Pros:
Good power over 400 fps using actual lead pellets.
Quicker reloading over shell loading revolvers
More shots per magazine reload, 8 versus 6.
Comes with two metal 8 round magazines.
Traditional single and double action trigger.
White dot front sight with fully adjustable rear sight.
Good weight and feel to it.
Fit and finish look good.
Recessed barrel for realistic looking barrel opening.
Should be able to use a dovetail type scope mount for adding on a red dot or magnified scope.
Cons:
Not a fan of the loose pistol grip setup to access the CO2.
Was hoping to get a bit tighter grouping but may have been a pellet choice issue.
Comments:
It was nice reviewing the Gamo PR-776 CO2 .177 Caliber Pellet Revolver as it was a bit different then most of today shell loading revolvers. I like that the Gamo PR-776 CO2 .177 Caliber Pellet Revolver still offered a realistic looking cylinder that the shell loading revolvers have but with the moon clip style magazines that allow for quick adn easy reloading of 8 rounds at a time. The velocity or power of the Gamo PR-776 CO2 .177 Caliber Pellet Revolver was even a bit high than Gamo claims using PBA Platinum pellets since Gamo claims 400 fps using these 5.1 grain lead pellets. My testing with closer to 7 grain pellets yielded fps up and over 400 fps. All the Gamo PR-776 CO2 .177 Caliber Pellet Revolver needs is to be just a little bit more accurate but I feel this may simply be more of a pallet choice, once you find a pellet the Gamo PR-776 CO2 .177 Caliber Pellet Revolver likes I am pretty sure it will deliver accurate shots.
My Table Top Review for the Gamo PR-776 CO2 .177 Caliber Pellet Revolver:
Make sure to watch my upcoming Table Top Review for the Gamo PR-776 CO2 .177 Caliber Pellet Revolver where I go over the specifications, pros and cons and show it up nice and close. In this Field Test Shooting Video I determine what the accuracy and velocity of the Gamo PR-776 CO2 .177 Caliber Pellet Revolver by testing out the fps with my Chronograph along with a accuracy test shooting a paper target at a distance of 30 feet away using a rested shooting position.
For the velocity test I placed a brand new CO2 Cartridge in the Gamo PR-776 CO2 .177 Caliber Pellet Revolver and shot five 6.9 grain lead pellets though my Chronograph. Gamo claims their 5.1 grain PBA Platinum pellets will shoot around 400 fps so I was expecting something in the low to mid 300’s but was surprised at a five shot average of 4115 fps with the much heavier RWS6.9 grain pellets. The slowest shot I achieved was 396 fps while the fastest shot was 434 fps. The temperature was right around 24 degrees Celsius or 75 degrees Fahrenheit.
For the next section of my Field Test Shooting Review I setup a brand new paper target 30 feet down range and loaded up two eight round magazines. The results for the Gamo PR-776 CO2 .177 Caliber Pellet Revolver where a bit confusing with both eight round magazines. It seemed like most of the shots wanted to group within about 1-2 inches of each other but I was getting several outliers that extended the grouping to closer to four inches. Not the best performance but as I have found with many guns, sometimes you need to find a pellet that the gun is happy with. the wrong pellet can really make a difference and I am fairly sure this was the case with the Gamo PR-776 CO2 .177 Caliber Pellet Revolver using the RWS pellets. just not the best choice for it.
The Gamo PR-776 CO2 .177 Caliber Pellet Revolver overall performer well, like I said I really think pellet choice will be the deciding factor in how accurate it is going to be. The velocity was very good for a CO2 Pellet revolver considering I was suing actual lead pellets and not the alloy pellets Gamo was using as their reference. The Gamo PR-776 CO2 .177 Caliber Pellet Revolver uses metal eight round magazines which are easy to preload and allow for two additional shots over the more common these days shell loading revolvers, which makes the Gamo PR-776 CO2 .177 Caliber Pellet Revolver more practical as a target pistol allowing for more power and easier loading.
Make sure to watch my Table Top view for the Jag Arms SPX2 Scattergun Green Gas Airsoft Shotgun where I take a closer look a talk about the specifications and go over the Pros and Cons.
In this Field Test Shooting Video I test out the Jag Arms SPX2 Scattergun Green Gas Airsoft Shotgun to see what the fps velocity is when shooting in 3 and 6 round burst modes. I also shoot a target 30 feet away again in both 3 shot burst and 6 shot burst mode tor see what the accuracy and groupings look like.
Starting with the velocity performance of the Jag Arms SPX2 Scattergun Green Gas Airsoft Shotgun. Using .25 gram Airsoft BB’s I placed several shots through my chronograph in 3 shot burst mode and averaged around 325 fps. When I switched over to 6 round burst mode the fps did not really change much averaging 321 fps. This was interesting since I thought adding Airsoft BB’s would slow the fps down but it did not.
I then setup a paper target 30 feet away to test out the accuracy or should I say grouping of the Jag Arms SPX2 Scattergun Green Gas Airsoft Shotgun. I was not excepting any 1 or two inch groupings since the Jag Arms SPX2 Scattergun Green Gas Airsoft Shotgun is designed to shoot like a shotgun and spread out the BB’s to some degree. I did find that the Jag Arms SPX2 Scattergun Green Gas Airsoft Shotgun out of the box shot a bit low but the front sight is adjustable for elevation so this is easy to correct. In both 3 and 6 round burst mode hitting the approximate 1 foot by 1 foot target was no problem and at this distance I would say the Airsoft BB’s spread out about 3-4 inches form each otters in both 3 and 6 shot burst modes.
Overall the Jag Arms SPX2 Scattergun Green Gas Airsoft Shotgun is a really fun Airsoft Shotgun to shoot. You get a lot of shots per green gas fill (around 100) and the fps is right on the money just over 300 fps both 3 and 6 shot burst. If you are looking for something a bit different then what most people are using on the field than the Jag Arms SPX2 Scattergun Green Gas Airsoft Shotgun will for sure catch some looks.
Type: Pump Action Shotgun.
Manufacturer: Jag Precision
Model: Jag Arms SPX2 Scattergun.
Materials: Mostly aluminum metal construction.
Weight: 4 Pounds (1.8 kg).
Barrel Length: 11 inches
Total Length: 31 inches.
Propulsion: Green gas or propane
Action: Pump action 3/6 rounds burst.
Ammunition Type: 6mm Airsoft BB’s
Ammunition Capacity: 28-30 rounds per shell.
Max FPS: 350-400 fps.
Trigger Pull: Since the Jag Arms SPX2 Scattergun Green Gas Airsoft Shotgun is a pump action shotgun you will need to work the pump action to load rounds into the barrel and cock the internal firing mechanism. The tigger is then engaged as a single action only trigger. The trigger pull is short and light. You can also hold the trigger down and pump the action for quick repetition shooting.
Accuracy: So far I have not tested the Jag Arms SPX2 Scattergun Green Gas Airsoft Shotgun but will be making my Field Test Shooting Video later this week. I have played around with the Jag Arms SPX2 Scattergun Green Gas Airsoft Shotgun and it seems to shoot pretty hard and the multi-round shots group fairly close together.
Build Quality: The build quality of the Jag Arms SPX2 Scattergun Green Gas Airsoft Shotgun is excellent. Most of the Jag Arms SPX2 Scattergun Green Gas Airsoft Shotgun is made out of aluminum with only a few parts made out of plastic including the pistol grips, rear stock and perhaps the side saddle for holding the shotguns shells/magazines.
Realism: The Jag Arms SPX2 Scattergun Green Gas Airsoft Shotgun is an awesome replica of a tactical fully tricked out pump action shotgun complete with AR accessories and rails for mounting whatever accessory you can dream of. Shells will not eject when pumping the Jag Arms SPX2 Scattergun Green Gas Airsoft Shotgun since the shells are essentially the magazines holding up to 30 rounds each.
Pros:
Full metal construction (mostly aluminum)
Comes pretty much fully loaded, nothing really to add on unless you want to customize it.
Tons of shots per gas fill with expected good fps.
Fully adjustable and removable pop-up iron sights.
AR compatible pistol grip and but stock.
Multiple mounting points for a sling.
Side saddle holds 6 rounds, 2 more just in case can be placed in the magazine tube.
3 or 6 round burst selectable.
The SPX2 comes in tan or black, lots of other options available.
Well priced for what you get compared to other gas Airsoft shotguns
Cons:
Does come with an orange tip but I am sure it can be removed.
Pump tube will show wear marks over time.
Will not be as accurate as an Airsoft rifle.
Comments:
The Jag Arms SPX2 Scattergun Green Gas Airsoft Shotgun is a really cool product. So far I have not come across a Green Gas Pump Action Airsoft Shotgun so this was a real treat for me. The build quality and the realism of the Jag Arms SPX2 Scattergun Green Gas Airsoft Shotgun is what I really like. It feels like a real shotgun and even performs much like one. Having the ability to shoot either 3 or 6 round bursts is also nice. If you want more shots per shell load then you can use the 3 round option, likewise if you select 6 round burst for more ammo down range with each shot. I like that the Jag Arms SPX2 Scattergun Green Gas Airsoft Shotgun comes pretty much all tricked out so you really don’t need to spend additional money on a bunch of accessories which adds a lot of value to this purchase.
My Table Top Review for the Jag Arms SPX2 Scattergun Green Gas Airsoft Shotgun:
