For this Field Test Shooting Video I actually had to go outside and use my field so in order to have an appropriate amount of distance to properly test the Umarex AirJavelin Archery CO2 Arrow Rifle. My Indoor Airgun Shooting Range is only 30 feet long and my metal backstop was simply not usable for the arrows.
I setup a make ship arrow backstop using a large bag of bark mulch with a rubber matt over top. This setup seemed to work really well for the Umarex AirJavelin Archery CO2 Arrow Rifle allowing the arrows to stick in most of the way. My target was setup around 55 feet away and I was using rested but standing shooting position for my testing.
I decided to combine the Chromo and Accuracy portion of my Field Test Shooting Video for the Umarex AirJavelin Archery CO2 Arrow Rifle by recording each shot on my chronograph while I placed shots on target, why not right? I placed 6 arrows on target with 5 of my shots being recorded by the chronograph. The average fps was only 156, the highest being 183 and lowest being 136. I did experience a bit of a CO2 leak when I first placed my 88 gram CO2 in the Umarex AirJavelin Archery CO2 Arrow Rifle. I believe this was because I did not pull the bolt back which allowed the valve mechanism to be open slightly. I realized this fairly quickly and pulled the bolt back which saved most of the CO2 but I did lose a some. This may have lowered the fps a little bit but I was surprise that the Umarex AirJavelin Archery CO2 Arrow Rifle was recording about half the fps claimed by Umarex. That said the effectiveness of the arrows and penetration into the backstop would for sure get the job done if I was trying to eradicate some small to medium sized pests.
In terms of accuracy I was very impressed with the Umarex AirJavelin Archery CO2 Arrow Rifle. At 55 feet or so I was able to get 5 of the arrows all within 2-3 inches of each other, I did have one arrow drop a little bit lower than the main grouping. I’m not sure if I would want to shoot a pest out at 50-60 feet but it could be done with the Umarex AirJavelin Archery CO2 Arrow Rifle especially if you where to add a nice red dot or optical sight to it. I would think the Umarex AirJavelin Archery CO2 Arrow Rifle would be best suited shooting small to medium game at 30-40 feet which should allow for sub 2 inch groupings.
Type: Archery. Manufacturer: Umarex. Model:AirJavelin & AirSaber. Materials: Metal & polymer construction. Weight: 3.9 pounds / 6.3 pounds no scope. Foot Pounds Energy: 34 ft/lbs / 124 ft/lbs. Total Length: 34 inches / 41 inches. Propulsion: 88 gram CO2 x1 / PCP 3625 PSI, 250 cc. Action: Bolt single action. Ammunition Type: Carbon fiber 190 grain / 350 grain arrows (Field tip can be swapped over to broad-head) Ammunition Capacity: 1 Arrow. Max FPS: 300 / 450.
Trigger Pull: The trigger pull on both the Umarex AirJavelin and the Umarex AirSaber are both single action that require the bolts to be pulled back in order to shoot them. The Umarex AirJavelin trigger is not as short, light or crisp as the Umarex AirSaber, the Umarex AirSaber for sure feels higher quality as expected.
Accuracy: This is going to be very interesting as I have never shot anything like this before but from what I was told at SHOT Show this year I can expect very accuracy results from both the Umarex AirJavelin and the Umarex AirSaber Archery CO2 and PCP Arrow Rifles. I’m not sure if I will test the Umarex AirSaber unless I can make a safe shooting range for it, luckily I live out on average so as long as I can setup a good backstop I should be able to test them both.
Build Quality: The build quality of the Umarex AirJavelin and the Umarex AirSaber Archery CO2 and PCP Arrow Rifles is very good overall, the Umarex AirJavelin is mostly plastic and is not very heavy but the fit and finish is good all round. The Umarex AirSaber on the other hand has a lot of metal used in the construction, the only real plastic found on the Umarex AirSaber would be in the stock. The Umarex AirSaber is for sure a step up in quality over the Umarex AirJavelin but will cost you almost double in the end.
Realism: This is going to be pretty short section since both the Umarex AirJavelin and the Umarex AirSaber Archery CO2 and PCP Arrow Rifles are not replicas of any actual gun in production. Their primary use is going to be for hunting and or pest control I would say.
Pros:
Only Canada non PAL Airguns with enough power to hunt medium and larger game.
Overall price point is good, nothing like this to compare to.
Arrows are propelled from the front, no archers paradox when aiming.
Arrows come with field tip arrows but can be unscrewed and replaced with broad tip arrows for hunting.
Easy to use cross bolt safeties.
Pistol grips allow for easy hold and control.
Fit and finish is very good and excellent on the AirSaber.
AirJavelin: 88 Gram CO2 for quick easy use.
AirSaber: PCP for more power and larger game options.
AirJavelin: White dot up front with fully adjustable peep sight on back.
AirJavelin: M-Lock on sides for adding accessories.
AirSaber: Picatinny rails on top for scope, sides and bottom for accessories.
AirJavelin: Adjustable AR-style rear stock.
AirJavelin: Rubber buttplate for added comfort.
Cons:
No scope or sights with base model AirSaber so you will need to get one for it.
Not a lot of shots per 88 gram CO2, will need a pump for the PCP AirSaber.
Arrows are not cheap so make sure of your shots.
Comments: The Umarex AirJavelin and Umarex AirSaber Archery CO2 and PCP Arrow Rifles are very interesting in that they are really the only Canada legal “firearms” that can actually put down small, medium and even large game without requiring a firearms license (PAL). This is because they do not exceed 500 fps, they do exceed the foot pound energy limit of 4.2 foot pounds but since both of these rifles do not exceed the 500 fps limit they do not exceed both requirements to place them in the regulated firearms category that requires a firearms license. This is great news for anyone in Canada without a PAL license that wants to be able to hunt various game or take care of pests humanly. Umarex has also been kind enough to bring us two variations on this design. The Umarex AirJavelin more economical and easier to use CO2 powered version designed for small to medium sized game and the Umarex AirSaber higher quality PCP powered big brother version designed to be used even for larger game. Both are great, all you need to do is pick which one is right for you!
My Table Top Review for the Umarex AirJavelin and AirSaber Archery CO2 and PCP Arrow Rifles:
Type: Pellet Revolver. Manufacturer: Gamo Model:PR-776. Materials: Mostly metal construction. Weight: 2.2 Pounds (1 kg). Barrel Length: 6 inches Total Length: 11.5 inches. Propulsion: CO2 x1 Action: Revolver single and double action. Ammunition Type: .177 caliber pellets. Ammunition Capacity: 8 rounds per magazine. Max FPS: 400+ fps.
Trigger Pull: The Gamo PR-776 CO2 .177 Caliber Pellet Revolver has your traditional revolver single and double action trigger setup. In double action, the trigger is going to be a bit longer and heavier but it feel fairly smooth with no real friction points and I would consider it to have a medium trigger pull. When you cock the hammer back placing the Gamo PR-776 CO2 .177 Caliber Pellet Revolver in single action, the trigger pull becomes very short with virtually no take-up at all and the weight of the trigger is very light allowing for more accurate shots.
Accuracy: Make sure to watch my Field Test Shooting video for the Gamo PR-776 CO2 .177 Caliber Pellet Revolver where I test out the velocity and accuracy in the Replica Airguns Indoor Airgun Shooting Range. In summary the Gamo PR-776 CO2 .177 Caliber Pellet Revolver shot a little bit hotter than claimed at just over 400 fps using around 7 grain lead pellets. In terms of accuracy with a total of 16 shots the grouping spread out to around 4 inches but I am pretty sure a different pellet choice may have made a difference.
Build Quality: The build quality of the Gamo PR-776 CO2 .177 Caliber Pellet Revolver is pretty good overall. It is mostly all metal with the exception of the grips of course, Fit and finishes looks good, everything feel snug adn tight with the exception of the pistol grips. I feel like the grips could easily move out of place and get caught on something. This is not a problem when shooting, more so when in a holster. The Gamo PR-776 CO2 .177 Caliber Pellet Revolver feels good in the hadn't, nice and solid and with a good weight to it.
Realism: The Gamo PR-776 CO2 .177 Caliber Pellet Revolver is a decent looking Airgun in the style of a traditional revolver, I wouldn’t say it’s an exact replica of any specific revolver in production but it does tick off all the boxes in terms of looking realistic. The weight and feel for now and the Gamo PR-776 CO2 .177 Caliber Pellet Revolver also has a recessed barrel and hidden CO2 crew. The only real giveaway would be the cylinder size as it is a bit smaller than expected and of course is chambered for .177 caliber pellets.
Pros:
Good power over 400 fps using actual lead pellets.
Quicker reloading over shell loading revolvers
More shots per magazine reload, 8 versus 6.
Comes with two metal 8 round magazines.
Traditional single and double action trigger.
White dot front sight with fully adjustable rear sight.
Good weight and feel to it.
Fit and finish look good.
Recessed barrel for realistic looking barrel opening.
Should be able to use a dovetail type scope mount for adding on a red dot or magnified scope.
Cons:
Not a fan of the loose pistol grip setup to access the CO2.
Was hoping to get a bit tighter grouping but may have been a pellet choice issue.
Comments: It was nice reviewing the Gamo PR-776 CO2 .177 Caliber Pellet Revolver as it was a bit different then most of today shell loading revolvers. I like that the Gamo PR-776 CO2 .177 Caliber Pellet Revolver still offered a realistic looking cylinder that the shell loading revolvers have but with the moon clip style magazines that allow for quick adn easy reloading of 8 rounds at a time. The velocity or power of the Gamo PR-776 CO2 .177 Caliber Pellet Revolver was even a bit high than Gamo claims using PBA Platinum pellets since Gamo claims 400 fps using these 5.1 grain lead pellets. My testing with closer to 7 grain pellets yielded fps up and over 400 fps. All the Gamo PR-776 CO2 .177 Caliber Pellet Revolver needs is to be just a little bit more accurate but I feel this may simply be more of a pallet choice, once you find a pellet the Gamo PR-776 CO2 .177 Caliber Pellet Revolver likes I am pretty sure it will deliver accurate shots.
My Table Top Review for the Gamo PR-776 CO2 .177 Caliber Pellet Revolver:
Make sure to watch my upcoming Table Top Review for the Gamo PR-776 CO2 .177 Caliber Pellet Revolver where I go over the specifications, pros and cons and show it up nice and close. In this Field Test Shooting Video I determine what the accuracy and velocity of the Gamo PR-776 CO2 .177 Caliber Pellet Revolver by testing out the fps with my Chronograph along with a accuracy test shooting a paper target at a distance of 30 feet away using a rested shooting position.
For the velocity test I placed a brand new CO2 Cartridge in the Gamo PR-776 CO2 .177 Caliber Pellet Revolver and shot five 6.9 grain lead pellets though my Chronograph. Gamo claims their 5.1 grain PBA Platinum pellets will shoot around 400 fps so I was expecting something in the low to mid 300’s but was surprised at a five shot average of 4115 fps with the much heavier RWS6.9 grain pellets. The slowest shot I achieved was 396 fps while the fastest shot was 434 fps. The temperature was right around 24 degrees Celsius or 75 degrees Fahrenheit.
For the next section of my Field Test Shooting Review I setup a brand new paper target 30 feet down range and loaded up two eight round magazines. The results for the Gamo PR-776 CO2 .177 Caliber Pellet Revolver where a bit confusing with both eight round magazines. It seemed like most of the shots wanted to group within about 1-2 inches of each other but I was getting several outliers that extended the grouping to closer to four inches. Not the best performance but as I have found with many guns, sometimes you need to find a pellet that the gun is happy with. the wrong pellet can really make a difference and I am fairly sure this was the case with the Gamo PR-776 CO2 .177 Caliber Pellet Revolver using the RWS pellets. just not the best choice for it.
The Gamo PR-776 CO2 .177 Caliber Pellet Revolver overall performer well, like I said I really think pellet choice will be the deciding factor in how accurate it is going to be. The velocity was very good for a CO2 Pellet revolver considering I was suing actual lead pellets and not the alloy pellets Gamo was using as their reference. The Gamo PR-776 CO2 .177 Caliber Pellet Revolver uses metal eight round magazines which are easy to preload and allow for two additional shots over the more common these days shell loading revolvers, which makes the Gamo PR-776 CO2 .177 Caliber Pellet Revolver more practical as a target pistol allowing for more power and easier loading.
Make sure to watch my Table Top view for the Umarex REKT OPFOUR CO2 Foam Dart Rifle where I take a closer look a talk about the specifications and go over the Pros and Cons.
Umarex claims the Umarex REKT OPFOUR CO2 Foam Dart Rifle will perform with 30% faster and farther shots than a similarly styled rifle. If you look up the average speed of a Nerf Gun on Google, Wikipedia says that it is a around 70 fps and Umarex claims 90+fps. I placed 7 shots through my Chronograph averaging 127 fps, the slowest shot was 100 fps and the fasters shot was 148 fps do a fairly big spread. faster shots hitting close to 150 fps will hurt so be careful!
Next I wanted to see if the Umarex REKT OPFOUR CO2 Foam Dart Rifle can actually hit a person sized target at around 30 feet which I feel would be about the max distance you would be shooting the Umarex REKT OPFOUR CO2 Foam Dart Rifle as you will probably using it indoors or outside but in close proximity. My paper target is about 1 foot by 1 foot in size which is around the same size as a human torso. If I can hit that from 30 feet then I should be able to hit a person. The Umarex REKT OPFOUR CO2 Foam Dart Rifle was able to reach out 30 feet no problem but during the last 10 feet the Nerf style darts did seem to veer off target. I was able to get some of the darts on target but found that at 20 feet it was way more consistent. So try and get in a bit closer if you want to be more sure of placing an accurate shot on target. By the way the dart will travel as far as 150 feet.
Type: Nerf Type Gun. Manufacturer: Umarex Model:REKT OPFOUR. Materials: Mostly plastic build with some internal metal parts. Weight: 1 pound 8 oz (680 grams). Length: 30 inches (762mm). Propulsion: 12 gram CO2 x2. Action: Pump single action. Ammunition Type: Nerf type foam darts. Ammunition Capacity: 12 rounds. Max FPS: NA. Claimed 30% faster and 30% father than standard similar type Nerf spring pistols.
Trigger Pull: The trigger on the Umarex REKT OPFOUR CO2 Foam Dart Rifle is what you would expect form a single action only trigger. Very little take up with a crisp light release. When you pull the Free Grip back you are working the pump action which loads a dart into the breach and at the same time cocks the internal hammer/striker.
Accuracy: I haven’t performed my Field Test Shooting video for the Umarex REKT OPFOUR CO2 Foam Dart Rifle but I can say after play around with it I expect it to shoot a lot harder than 90 fps. When the dual CO2 system is fully charged I was getting some pretty ferociously fast shots form the Umarex REKT OPFOUR CO2 Foam Dart Rifle. I would say it was even able to shoot out into my yard at least 150+ feet. I was even a bit concerned shooting the Umarex REKT OPFOUR CO2 Foam Dart Rifle inside my house as it is possible to dent walls with the Nerf Darts. IN terms of accuracy it seems pretty good but I will know more once I have made my Field Test Shooting Video later this week.
Build Quality: The Umarex REKT OPFOUR CO2 Foam Dart Rifle is built pretty much exactly like other Umarex all plastic CO2 BB guns and that’s a good thing since they are pretty much bullet proof. I would even go on record to say the Umarex REKT OPFOUR CO2 Foam Dart Rifle is built better or should I say stronger than a Standard Nerf gun in terms of plastic thickness and even the fit and finish is very good.
Realism: One big advantage over most Nerf Guns is that the Umarex REKT OPFOUR CO2 Foam Dart Rifle looks a lot more like a real gun, it’s about the same size, has the same feel and looks a lot like a modern AR Rilfe other than the bright coloring going on. Ergonomically speaking the Umarex REKT OPFOUR CO2 Foam Dart Rifle would make a much better trainer than a Nerf gun since it is close to a one to one scale replica.
Pros:
No need to work a spring before each shot because of the CO2 power source.
More power and range than a traditional Nerf Gun.
More realistic looking than most Nerf Gun.
Like an Airsoft Gun but more usable indoors and less chance of injury.
Rear Peep sight is removable and can be swapped out.
Has a working selector switch safety.
Uses Standard Nerf Foam Darts.
Picatinny Rail top and sides for adding on accessories.
Dual CO2 system for extended shooting time before changing.
A great option for having some indoor fun!
Cons:
Will require CO2 x2.
May actually be a bit too powerful and can cause damage or injury if not careful?
More money than a traditional similar type Nerf rifles.
Comments: The Umarex REKT OPFOUR CO2 Foam Dart Rifle may be the ideal indoor fun Nerf styled rifle right now while we are all staying at home a lot more these days. Sure you could use a standard Nerf Gun but having a CO2 powered AR-15 looking Nerf gun is way cooler! I like that the Umarex REKT OPFOUR CO2 Foam Dart Rifle is more realistic looking then a traditional Nerf Gun, perhaps the perfect intermediary gun if you want something between a Nerf Gun and an Airsoft Gun? If you’re interested in a pistol version of the REKT line of Nerf Dart shooting guns then checkout the REKT OPSIX.
My Table Top Review for the REKT OPSIX CO2 Single Shot Foam Dart Launcher:
Type: BB Rifle. Manufacturer: Crosman. Model: R1 AR. Materials: Metal & plastic. Weight: 6 pounds (2.7 kilograms). Length: 26.25 / 29.25 inches (Stock closed / extended). Propulsion: 12 gram CO2 dual cartridges. Action: Blowback - single action only. Ammunition Type: 4.5mm steel BB's. Ammunition Capacity: 25 rounds. FPS: 430fps. Rate of Fire: 1400 rounds per minute in full auto
Trigger Pull: The trigger pull on the Crosman R1 CO2 Blowback BB Machine Gun is single action only since the charging handle must be cocked first before you can shoot it. The trigger is short and fairly light as you would expect from an AR type trigger action. The real fun happens with the Crosman R1 CO2 Blowback BB Machine Gun when you switch it over to full auto mode and with just one pull and hold of the trigger you empty the 25 round magazine in mere seconds.
Build Quality: The Crosman R1 CO2 Blowback BB Machine Gun is well made all around. Weighing in at 6 pounds without any add on accessories it feel solid and well built. There is a lot of metal going on inside and out of this rifle but keep in mind the top and bottom receiver are plastic with metal parts where they need to be like in the internals, pretty much all the working parts are metal, the magazine is full metal, the buffer tub is metal, charging handle, selector switch, magazine release, bolt release, trigger and of course the barrel is metal.
Realism: The Crosman R1 CO2 Blowback BB Machine Gun is about as real as you are going to get in a CO2 Blowback AR/M4 styled Airgun. You can even take it apart and split the top and bottom receivers like the real steal version. The blowback action gives you some recoil but more importantly offers a true single action trigger and of course the full auto ability we all love. Almost all the working parts work like they would on a real AR / M4 other than the forward assist which is moulded into the receiver.
Pros:
Super realistic working M4/AR 4.5mm BB Rifle just like the otters Crosman Rifles in this lineup.
Full blowback operation with both semi and full auto shooting, can feel the blowback operation rocking the gun.
Great weight and feel to it.
Almost everything works exactly like the real steel version. (Charging handle, dust cover, bolt release, magazine release, selector switch…)
Duel CO2 full metal drop out magazine that holds the 25 4.5mm steel BB’s as well.
Adjustable and customizable AR butt stock.
Included red dot sight and ability to add pop-up iron sights.
Lots of rails of mounting additional cool hardware.
Removable flash hider that uses standard threading.
Cons:
Receiver is plastic but well made and does not compromise feel or weight since there is lots of metal throughout this gun.
No iron sights included.
Comments:
The Crosman R1 CO2 Blowback BB Machine Gun is really pretty much the same as the Crosman DPMS SBR and Crosman MPW with more or less Cosmetic changes. Like the Crosman MPW the Crosman R1 has an AR compatible Rear stock and pistol grip, the Crosman R1 CO2 Blowback BB Machine Gun is the only Crosman AR Full Auto CO2 BB Rifle that has the ability to change out the flash hider, you can even put a mock suppression or in it if you choose to. No matter which of the Crosman AR Full Auto CO2 BB Rifles you chooses to get they are mechanically every similar and share most of the same parts. I would say the Crosman R1 CO2 Blowback BB Machine Gun is the most customizable to date but they are all fantastic Air Rifles!
My Table Top Video of the Crosman R1 CO2 Blowback BB Machine Gun:
Here we are with yet another Crosman AR styled Full Auto Blowback CO2 BB Rifle and they just keep getting better, I say that lightly as even the first version the Crosman DPMS SBR still holds up to the 3 part lineup. It kind of has to since all three of them can be mixed and matched in terms of the uppers and lowers, magazines and I am sure most intern parts. Check out the Crosman DPMS SBR and the Crosman MPW for reference as I have made full table top and field test shooting videos for them already.
The purpose as always for my Field Test Shooting Videos is to find out how the airgun being reviewed performs in terms of velocity and accuracy, and if the ratings on paper end up being the same or close to the tested results. Crosman claims the Crosman R1 CO2 Blowback BB Machine Gun is capable of shooting 5.1 grain 4.5mm Steel BB’s at up to 430 fps. When I tested the Crosman R1 CO2 Blowback BB Machine Gun using my Chronograph averaging out 5 shots using a brand new set of CO2 cartridges I averaged 395 fps. Note the temperature in my Indoor Airgun Sea Can Shooting Range was about average at about 24 degrees Celsius or right around 75 degrees Fahrenheit. Comparatively I was able to get 405 fps from the Crosman DPMS SBR and around 385 fps with the Crosman MPW. Temperature may have beene slightly different on those testing days so that needs to be factored in.
Moving on to the accuracy portion of this Field Test Shooting Review for the Crosman R1 CO2 Blowback BB Machine Gun, I placed 10 semi auto shots on my paper target setup 30 feet downrange. I was using a rested and seated shooting position to help minimize human factor. I was able to get pretty much a 1 inch grouping with my 10 semi auto shots which was nit surprising as I have been able to get tight shot placement like this from the Crosman AR series before.
I then flipped the Crosman R1 CO2 Blowback BB Machine Gun semi auto selector switch to full auto and dumped the remaining 10 rounds into my paper target in full auto mode flowed by another full 25 round magazine again in full auto and the grouping only stretched out to about 2.5 -3 inches even with all the full auto vibrations and rocking around of the gun. Shot placement was a little bit high and to the left but this can easily be corrected using the red dot sight adjustments.
In summary the Crosman R1 CO2 Blowback BB Machine Gun performed a lot like the Crosman DPMS SBR and the Crosman MPW which makes since since all of them are virtually mechanically the same. In the end I think it really comes down to which of the Crosman AR type full auto BB rifles you like the look of since they areal very capable shooters. If you can’t decide then maybe get one of each :)
Starting with my Chronograph velocity testing for the Sig Sauer MCX ASP .177 Caliber CO2 Pellet Rifle, I used a brand new Sig branded 90 gram CO2 cartridge along with 6.9 grain RWS pellets. The temperature was 24 degrees Celsius (75 degrees Fahrenheit) in the Sea Can Indoor Airgun Shooting Range. Sig claims the Sig Sauer MCX ASP .177 Caliber CO2 Pellet Rifle to shoot up to 5.7 Joules. My Chrono testing resulted in an average fps of 418 with the 6.9 grain lead pellets which yielded a 3.7 Joule (2.7 foot pound) power output. I was not expecting 5.7 joules as that would have been closer to 600 fps using 6.9 grain pellets.
Next I setup a fresh paper target 30 feet down range and using seated and rested shooting position I placed 10 rounds into the target. The Sig Sauer MCX ASP .177 Caliber CO2 Pellet Rifle shot a decent 1.5 inch 10 round grouping but I am pretty sure I can get better results once I find the right pellet, I have found this especially to be true with Sig Air Rifles. My MCX Virtus was able to get 1/2 inch groupings at 50 feet once I found ammo it liked and my MPX also shot a bit tighter form 30 feet out with a different ammo selection. I then unload the remaining 15 rounds in to the target rapid fire, followed by another 30 round full magazine and the grouping only stretched out a little bit, closer to 2 inches. Shots placed on the target a little bit low and to the right but this can be easily corrected for consistent bullseyes using the fully adjustable sights.
The Sig Sauer MCX ASP .177 Caliber CO2 Pellet Rifle performed well for me in general, I did find that occasionally the belt did not index resulting in a misfire (no pellet fired) but the next pull of the trigger would index the belt resulting in a pellet firing, there where no jams and all rounds from the belt where fired. I am not sure why this happened as this did not happen to me with my other Sig Sauer Air Rifles. Perhaps I short triggered it a bit not getting a full belt index. I know many of you have been waiting for a Canadian version of the Sig Sauer MCX ASP .177 Caliber CO2 Pellet Rifle, now that we have them in the All Black Iron Sight Version and FDE Red Dot Version, make sure to get one as once we run out I am pretty sure we will no longer be able to get these Canada Import Legal Sig Sauer MCX ASP .177 Caliber CO2 Pellet Rifles.
Watch my Preview Video where I take a quick look at the Sig Sauer MCX CO2 Pellet Rifle and Crosman R1 Full Auto BB Rifle. Full Table Top and Field Test Shooting Videos coming soon.
The Umarex T4E TR50 .50 Caliber Paintball Revolver is an interesting Paintball pistol, it has a very different look and also uses .50 caliber Paintballs which are a little bit less common than the .68 and .43 caliber paintball gun I have been reviewing up until now. The Umarex T4E TR50 .50 Caliber Paintball Revolver is some countries is marketed as a self defense gun but those versions do have a little bit more fps and foot pounds of energy. The version I am testing is not marketed here in Canada or the US as self defense products but rather as more of a training Paintball Gun.
Starting with my Chronograph velocity test I placed 5 Rubber Balls through my Chronograph using a brand new CO2. The Rubber balls I am going to say are a little bit heavier than standard Paintballs and Umarex claims the Umarex T4E TR50 .50 Caliber Paintball Revolver is capable of hitting around 360 fps so with the heavier rubber balls I was expecting a little bit under the max fps. I was able to get an average of 328 fps so not bad at all.
Moving on to my accuracy test. I need up placing 10 of my 12 rounds into the paper target as I had two rounds that went off in what I am going to call an uncontrolled manor. The 10 rubber paintball rounds that did hit my paper target that was setup 30 feet down range all hit within about 6 inches of each other daily well centered left and right and a little bit low on the target. Gettin back to the uncontrolled shots, I had a situation where I pulled the trigger and the Umarex T4E TR50 .50 Caliber Paintball Revolver went click as you would expect but no CO2 was expelled and so no round was shot. I thought perhaps the cylinder was caught up so I went to wiggle it to try and free it up. As I did so the gun went off without my finger anywhere near the trigger. I am glad I was using rubber balls since the rubber ball hit my cabinet leaning a biota a mark but really causing any damage. This happened twice with the same cylinder, the second time I was bit more prepared for it and had the gun pointed well downrange. I was not able to recreate this problem again so perhaps the cylinder magazine was not seated properly but this still concerns me a bit.
Overall I really like the Umarex T4E TR50 .50 Caliber Paintball Revolver, it’s a pretty cool looking Paintball Gun with decent accuracy and power, you can even feel a little push back and barrel lift when you shoot it. I also like that you can preload a CO2 and puncture it whenever hypo are ready to shoot with a quick smack on the bottom of the grip. Just made sure to put the CO2 in the right way :)
First, I put four rounds through my Chrony Chronograph to see what the real world FPS would be, keep in mind I was using rubber balls rather than paintballs and the rubber balls are a little bit heavier and smaller in diameter than paintballs so this could bring the FPS down a bit compared to the slightly lighter paintballs. Using a brand new CO2, the Umarex T4E TPM1 .43 Cal. Paintball Pistol average 303 FPS which was higher than the claimed 290 FPS. Temperature inside my Indoor Sea Can Airgun Shooting Range was around 22 degrees Celsius or 72 degrees Fahrenheit.
Moving on to my accuracy testing as per my usual indoor field tests, I positioned myself 30 feet back from a fresh paper target and using a seated and rested shooting position I shot a full magazine (8 rounds) of rubber balls on target with the Umarex T4E TPM1 .43 Cal. Paintball Pistol. As mentioned before I was expecting around a 6 inch grouping and got pretty close to it getting closer to an 8 inch 8 shot grouping. The rubber balls did center well on the target all placing uniformly arounds the bullseye. If I was aiming at a human sized torso, I would have hit it with every shot from 30 feet away so good enough for me.
As expected I was able to get very similar and decent results compared to the other Umarex .43 Caliber CO2 Blowback Paintball Pistols I have already reviewed. I did want to mention some of shooting qualities you will find with the Umarex T4E TPM1 .43 Cal. Paintball Pistol. The trigger can feel a bit heavy especially using rubber balls as when you pull the trigger the inner barrel moves back and into the magazine going around the paintball and helping to seal off the CO2 from escaping. There is a bit of friction and I find the rubber paintballs seem to have more friction perhaps because the rubber grips more than the plastic surface on standard paintballs? This extra trigger friction or heaviness is really only noticeable when you are pulling the trigger slowly for accuracy testing but when shooting quickly as you would be more likely to do so in an actual training simulation, the trigger friction is all but forgotten about.
Type: Paintball Gun. Manufacturer:Umarex - T4E. Model:T4E TPM1 Materials: Metal & Polymer. Weight: 532 grams (1.2 pounds). Barrel: Smooth bore. Power Source: 1x12 gram CO2. Action: Semi-Automatic with blowback action. Ammo Type: .43 Caliber Paintball or Rubber Ball. Ammo Capacity: 8 Rounds. FPS: 290.
Trigger Pull: The trigger pull on Umarex T4E TPM1 .43 Cal. Paintball Pistol feels a lot like a double action trigger mainly because when you pull the trigger the inner barrel travels backwards into the magazine placing a paintball round in the barrel which seals the barrel with the magazine so less CO2 is wasted. This does make the trigger a little bit longer and heavier than a single action trigger. I believe the internal hammer/striker is engaged from the blowback action.
Build Quality: The build quality of the Umarex T4E TPM1 .43 Cal. Paintball Pistol is really very good, metal parts are where you would expect them, the slide, slide catch, barrel, magazine and most internal parts giving the Umarex T4E TPM1 .43 Cal. Paintball Pistol a decent overall weight with the magazine in which makes the Paintball version a little bit lighter than a real steel Glock 17 (624 grams - 22 ounces). The Umarex T4E TPM1 .43 Cal. Paintball Pistol does have a polymer frame but again this is normal with todays modern guns and helps keep the weight down. Fit and finish is also very good!
Realism: The Umarex T4E TPM1 .43 Cal. Paintball Pistol is not an actual replica of the the Glock17 Pistol, it is Umarex’s version of the Glock, Umarex does now the Glock lisense but perhaps they where not able to find an actual Glock 17 Paintball gun they could bring to market. The T4E TPM1 is designed to hold and feel similar to a Glock and for most real steel Glock owners the Umarex T4E TPM1 .43 Cal. Paintball Pistol would be close enough for training purposes. You will find that the slide cycle distance is a bit shorter than it would be meaning that when the side catch is engaged the slide does not go as far back as it the real 9mm Glock. Field stripping the Umarex T4E TPM1 .43 Cal. Paintball Pistol will requires some tools and pin removal.
Full Metal slide that locks back on the last shot.
All metal heavy full size drop out magazine adds some additional weight to the gun.
Good for Glock shooters looking for a similar training weapon.
Everything works pretty much like the real gun so again great as a training tool.
Easy to see yellow dot sights front and back.
Working trigger safety.
Fit and finish is excellent.
Magazine spring release really shoots the magazine out.
43 caliber barrel opening, adds to realism.
Cons:
White warning lettering stands out a bit too m much on the slide.
Magazine only holds 8 rounds, so you are going to need extra magazines for sure.
Blowback action is not full blowback, more like a typical half blowback BB gun.
Comments:
TheUmarex T4E TPM1 .43 Cal. Paintball Pistol is mechanically very close to the Umarex Walther PPQ M2 .43 Cal. Paintball Pistol and the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol in how it functions as a Paintball Pistol so I expect all of them to shoot very similarly and that’s not a bad thing since previous versions I have tested so far have performed rather well for me in the Replica Airguns Sea Can Indoor Shooting Range. If you are a Glock fan than the Umarex T4E TPM1 .43 Cal. Paintball Pistol is about as close as you are going to get at least for now to a Glock Replica Paintball Pistol. As of right now being stuck at home, perhaps a Glock Paintball Trainer like the Umarex T4E TPM1 .43 Cal. Paintball Pistol using .43 caliber rubber ammo may just allow you to get some indoor shooting practice to keep your shooting skills up.
I wasn’t sure if I was going to do a traditional Field test Shooting video for the REKT OPSIX CO2 Single Shot Foam Dart Launcher but then I thought why not, and I’m kind of glad I did, it was a lot fo fun making it and now we all know what to expect for this line of CO2 powered Nerf styled guns.
Umarex claims the REKT OPSIX CO2 Single Shot Foam Dart Launcher will perform with 30% faster and farther shots than a similarly styled Nerf spring powered gun but what does that mean. If you look up the average speed of a Nerf Gun on Google, Wikipedia says that it is a around 70 fps so I guess we are shooting for around 100 fps (Pardon the pun). Well after placing 5 shots through my Chronograph and actually getting readings for most shots, I did end up averaging 104 fps so Umarex was bang on with their claim of 30% faster which makes sense to also assume 30% farther.
Next I wanted to see if the REKT OPSIX CO2 Single Shot Foam Dart Launcher can actually hit a person sized target at around 30 feet which I feel would be about the max distance you would be shooting the REKT OPSIX CO2 Single Shot Foam Dart Launcher as this is really an indoor fun gun. My paper target is about 1 foot by 1 foot in size which is around the same size as a human torso. If I can hit that from 30 feet then I should be able to hit a person. The REKT OPSIX CO2 Single Shot Foam Dart Launcher was able to reach out 30 feet no problem but during the last 10 feet the Nerf style darts did seem to veere off target. I was able to get some of them on target but found that at 20 feet it was way more consistent. So try and get in a bit closer if you want to be more sure of placing an accurate shot on target.
The REKT OPSIX CO2 Single Shot Foam Dart Launcher is for sure a step up from a spring powered Nerf pistol in terms of power, distance, quicker reloading and especially when it comes to realism as they look like a traditional modern styled hand gun rather than a toy gun like most Nerf gun designs. I figure why not grab a couple REKT OPSIX CO2 Single Shot Foam Dart Launchers for when you get bored around the house, heck there’s a lot of that going on right now!
As always I like to test each gun out in the Replace Airguns Indoor Sea Can Airguns Range first placing 5 rounds through my Chronograph to find out the real world velocity of each test gun, then I shoot 10 rounds at a distance of 30 feet onto a paper target to see how tight of a grouping I can get shooting from a seated and rested position. When it come to full auto BB guns like the Umarex Legends M1A1 Blowback CO2 BB Machine Gun, I will usually switch up to full auto and dump the rest of the magazine to see if I can still sray on target with the remaining rounds.
For my Power or Velocity test I was using fairly new CO2, I had shot a full magazine a couple days before but the Umarex Legends M1A1 Blowback CO2 BB Machine Gun was all warmed up and ready to perform optimally. Umarex does state that it will shoot around 435 fps and with my 5 shot test I was able to confirm that with a 434 fps average. The temperature in the Sea Can was around 23 degrees Celsius or 73 degrees Fahrenheit.
For my accuracy test I setup a new paper target 30 feet downrange and proceeded to place 10 shots into it using the peep sights on the Umarex Legends M1A1 Blowback CO2 BB Machine Gun. Other than one slight flyer my 10 round grouping was around 3/4 of an inch and just a tad low of the bullseye but pretty close. I then switched over to full auto fun mode and with the remaining BB’s I unloaded all 20 rounds in about a half a second, or at least it seemed like that! The Umarex Legends M1A1 Blowback CO2 BB Machine Gun even in full auto mode with the trigger matted till the gun ran out I was still able to get a 2 inch grouping!
I’m a big fan of the Umarex Legends Series BB Guns and the Umarex Legends M1A1 Blowback CO2 BB Machine Gun may be my favorite out of all of them to date. The Thompson M1A1 is just such a stand out Machine Gun we all know from the Mob shows. Not only does the Umarex Legends M1A1 Blowback CO2 BB Machine Gun look the part but it performs I would have to say so far the best when it comes to Full Auto Machine guns at least from Umarex. I do have to say that the Crosman CO2 BB AR Series does not disappoint. That said if you are looking for a more classic BB Machine Gun that performs as good as it looks then my advice is grab yourself one of the Umarex Legends M1A1 Blowback CO2 BB Machine Gun and add it to your collection.
Type: Air Rifle / Machine Gun. Distributer: Umarex Model:Legends M1A1. Materials: Mostly Metal build. Weight: 7.75 pounds (3.5 kilograms) Barrel: 12 inches - smooth bore steel. Propulsion: 2x12 gram CO2. Action: Internal BoltBlowback single action. Ammunition Type: 4.5mm Steel BB's. Ammunition Capacity: 30 round full size drop out magazine. Max FPS: 435.
Trigger Pull: The trigger pull on the Umarex Legends M1A1 Blowback CO2 BB Machine Gun is single action only so you will need to charge the bolt for the first shot just like you would on the real steel Thompson M1A1, after that the blowback operation will charge the bolt which allows for semi and full auto shooting. Trigger pull is not very long or heavy.
Build Quality: The Umarex Legends M1A1 Blowback CO2 BB Machine Gun is pretty much all metal other than the stock and pistol grip. Pretty much everything that is black is going to be metal on this CO2 airgun. It weighs in at a hefty 7.75 pounds which is lighter than the real steel version by about 2 pounds but keep in mind the simulated plastic wood grips are a much lighter than real wood would be. Overall the fit and finish is really good, mechanical parts work well and seem to be well machined..
Realism: The Umarex Legends M1A1 Blowback CO2 BB Machine Gun is a 1 to 1 replica of the real steel World War II Thompson M1A1 Machine Gun and is very authentic looking with similar operation. Even the magazine holds 30 rounds just like the real steel Thompson M1A1. The blowback operation will give you a little bit of that shoulder tap but of course nothing like a 45 caliber M1A1. As expected in todays Replica Airguns the barrel is recessed to give it a larger opening and the CO2 screw is hidden well enough. I would like to see at least a real wood kit for the Umarex Legends M1A1 Blowback CO2 BB Machine Gun which would not lonely look even better but also increase the overall weight closer to the 10 pound real steel weight.
Yet another Classic Legends Replica Airgun from Umarex, maybe one of the best to date.
Mostly all metal design with good overall weight.
Semi and Full auto select-ability.
Dual CO2 design for increased shots and less cool down effect.
High capacity 30 round full size drop out metal magazine.
Umarex went with less rounds to get away from the double stay configuration of the 50 round Legends MP40 which was not always dependable.
Great looking replica of the real steel M1A1 in looks, operation and feel.
Internal bolt blowback will give a bit of recoil feedback feel.
Simulated wood looks very realistic.
Recessed barrel for added realism.
Cons:
Real wood hardware would have been cine and added it of additional weight. Maybe Umarex will offer this down the road?
Price is getting up there a bit but still worth it if you are an M1A1 fan, imagine what a real one would cost?
Going to eat up CO2 quickly in full auto mode but you can always switch over to semi auto.
Comments: Another great Legends product from Umarex, maybe even the best one so far. The only issues I had with the Umarex Legends MP40 was the double stack magazine feeding dependability with the 50 round double stack magazine not always feeding consistently. Umarex went back to a less aggressive closer to a single stack magazine on the Umarex Legends M1A1 Blowback CO2 BB Machine Gun which has a fewer rods but is expected to feed more consistently. I am looking forward to getting out and actually shooting the Umarex Legends M1A1 Blowback CO2 BB Machine Gun when I make my Field Test Shooting video. My advice right now with uncertainties about if and when we will get new inventory is buy now if you are in a position to as I am not sure how long they will last and when we will be able to get more stock.
My Vimeo Table Top Review of the Umarex Legends M1A1 Blowback CO2 BB Machine Gun:
Type: Nerf Type Gun. Manufacturer: Umarex Model:REKT OPSIX. Materials: Mostly plastic build with some internal metal parts. Weight: 11.75 oz (332 grams) with CO2 installed. Propulsion: 12 gram CO2 x1. Action: Single shot double action trigger. Ammunition Type: Nerf type foam darts. Ammunition Capacity: 1 round. Max FPS: NA. Claimed 30% faster and 30% father than standard similar type Nerf spring pistols.
Trigger Pull: The trigger on the Umarex REKT OPSIX CO2 Single Shot Foam Dart Launcher is much the same as your standard double action non-blowback BB gun, I’m pretty sure the actual mechanical hammer and trigger mechanism is much the same since the barrel moves in and out just like many of Umarex’s non-blowback CO2 BB pistols. The double action trigger is as expected a bit long but it’s not overly heavy and since this is not a rapid fire gun your trigger finger will not get tired shooting the Umarex REKT OPSIX CO2 Single Shot Foam Dart Launcher.
Accuracy: I haven’t performed my Field Test Shooting video for the Umarex REKT OPSIX CO2 Single Shot Foam Dart Launcher and I’m not sure what that is going to entail but I have placed some rounds at targets around 20-25 feet away and for the most part you can easily hit a human sized object in the mid section easily enough. I would not want to shoot much over 30 feet but the Umarex REKT OPSIX CO2 Single Shot Foam Dart Launcher like other Nerf type guns is mainly for indoor fun.
Build Quality: The REKT OPSIX CO2 Single Shot Foam Dart Launcher is built pretty much exactly like other Umarex non-blowback all plastic CO2 BB pistols and that’s a good thing since they are pretty much bullet proof. I would even go on record to say the REKT OPSIX CO2 Single Shot Foam Dart Launcher is built better or should I say stronger than a Standard Nerf gun in terms of plastic thickness and even the fit and finish is very good.
Realism: One big advantage over most Nerf Guns is that the Umarex REKT OPSIX CO2 Single Shot Foam Dart Launcher looks a lot more like a real gun, it’s about the same size, has the same feel and looks a lot like a modern semi auto hand gun other than the bright coloring going on. Ergonomically speaking the REKT OPSIX CO2 Single Shot Foam Dart Launcher would make a much better trainer than a Nerf gun and should even fit into standard pistol holsters.
Pros:
No need to work a spring before each shot because of the CO2 power source.
More power and range than a traditional Nerf Gun (30% more).
More realistic looking than most Nerf Guns.
Like an Airsoft Gun but more usable indoors and less chance of injurys.
White dot sights front and back.
Has a working safety.
Uses standard Nerf foam darts.
Picatinny rail underneath for adding accessories.
A great option for having some fun indoors while many of us are shut in our houses.
Cons:
Will require CO2 to operate.
Requires reloading between each shot.
More money than a traditional similar type Nerf pistol.
Comments: The Umarex REKT OPSIX CO2 Single Shot Foam Dart Launcher may be the ideal indoor fun gun right now while we are all staying at home a lot more these days. Sure you could use a standard Nerf Gun but not if you want to be the cool kid (or cool kid stuck in an adults body). I like that the REKT OPSIX CO2 Single Shot Foam Dart Launcher is more realistic looking then a traditional Nerf Gun, perhaps the perfect intermediary gun if you want something between a Nerf Gun and an Airsoft Gun? Hopefully we can keep them in stock and get more product for you if need be moving forward.
My Vimeo Table Top Review for the REKT OPSIX CO2 Single Shot Foam Dart Launcher:
I want to thank Drew from Tippmann Armory/Air Ordnance for sending me this unit for review. I have been wanting to get my hands one of these Air-Ordnance SMG 22 .22 Caliber Full Auto Pellet Machine Guns for several years now and super glad I happened finally :) I really don’t think there is any airgun out there like it. I am really hoping that we will be able to have this one in both our Canada and US Online Replica Airguns Stores.
So what exactly is the Air-Ordnance SMG 22 .22 Caliber Full Auto Pellet Machine Gun? It’s a PCP powered semi/full auto .22 caliber pellet firing Airgun and it is available in a Canada legal version that shoots just under 500 fps allowing it to be classified here in Canada as an unregulated Firearm. Unregulated Firearms do not require a license or registration and do not have to abide by the same rules that regulated firearms have to such as full auto limitations, magazine capacities and size limitations. So in other words if you want a full auto .22 caliber Machine gun here in Canada this is going to be your only option at least for now.
Some other cool features about the Air-Ordnance SMG 22 .22 Caliber Full Auto Pellet Machine Gun is the trigger setup, pull it light and quick and you get a single shot, pull and hold using medium force and you get full auto but not at a super high rate of fire. Press and hold the trigger down hard and you get full auto with a much faster rate of fire so you control the rate of fire by how hard you press the trigger down. Air-Ordnance SMG 22 .22 Caliber Full Auto Pellet Machine Gun also has an adjustment to set the maximum rate of full auto fire.
