In this Field test Shooting Video I Test out the Specna Arms Core SA-C07-PDW AEG Airsoft Rifle in the Replica Airguns Indoor Airgun Shooting Range to find out what kind of velocity we can achieve using standard .20 gram Plastic Airsoft BB’s. I also shoot 10 rounds in semi auto at my paper target 30 feet down range to see what kind of grouping I can get and then switch it over to full auto and let her rip till I am basically out of ammo and see if I can punch a nice hole in my cardboard backed target. If you are looking for more details and specification along with some closer up video then make sure to watch my Table Top Review Video for the Specna Arms Core SA-C07-PDW AEG Airsoft Rifle.
Starting with my velocity test, I shot 5 rounds through my Chronograph using .20 gram Plastic Airsoft BB’s with the preinstalled spring and got an average of 402 fps with my lowest velocity being 400 and my highest velocity being 405 so really close in fps. You can tone down the Specna Arms Core SA-C07-PDW AEG Airsoft Rifle a bit b y installing the M90 Spring if you find the fps to be a bit high for close quarter battles.
For the accuracy portion of this Field Test Shooting Review I proceeded to fire 10 semi auto rounds into a paper target setup 30 feet away. I use a semi rested shooting position with the Specna Arms Core SA-C07-PDW AEG Airsoft Rifle resting on a sand bag up front and me sitting on a stool for stability. My 10 shot grouping was all within around 1 to 1.5 inches which is very good for an Airsoft Rifle shooting lighter Plastic BB’s. I then switched the selector into “fun mode” (Full Auto) and proceeded to hold the trigger down until I ran out of spring tension on the High Cap Magazine. I would say I got through around 100+ rounds with most of them making about a 2 inch hole in my target consisting of cardboard and of course the paper target in front of it.
I have reviewed the Specula Arms line of Airsoft Rifles in the past, both the Core and the Edge and they really are great Airsoft Guns. The Specna Arms Core SA-C07-PDW AEG Airsoft Rifle as expected lived up to my expectations and performed really great in this Field Test Shooting Video. If you like this model also make sure to checkout the other models Specna Arms Offers over in our Replica Airguns Canada and US Online Stores.
Type: Pellet Pistol. Distributer:Umarex. Model:Stainless Ruger Mark IV. Materials: Metal and polymer build. Weight: 1.56 pounds (708 grams). Barrel: 5.3 inches (135mm). Total Length: 11 inches (279mm). Propulsion: Spring Piston. Action: SAO Break Barrel. Ammunition Type: .177 caliber pellets. Ammunition Capacity: 1 round. FPS: 320.
Trigger Pull: The trigger pull on the Stainless Ruger Mark IV Break Barrel .177 Cal Pellet Pistolis not too bad, I feel it is a around 6-7 pounds or so without measuring. In comparison to a real steel 22LR semi auto SAO trigger pistol, the trigger is much heavier but most of these 22LR pistols of this nature have what I would consider to be near perfect triggers. Over time once you get use to the pressure and release point accuracy with this pistol it is for sure possible.
Accuracy: I have tested out the all black version of this pistol which will perform exactly the same or should I say is expected to perform the same since they are virtually the exact same Pellet Pistol but in different finishes. You can watch my Field Test Shooting Video for the all black version but in case you don’t make it there I will fill you in on the basic results… In terms of velocity I averaged 312 fps using 7 grain lead pellets and got around a 2 inch 7 rounds grouping but expect with a bit more trigger time to get closer to 1 inch.
Build Quality: The Stainless Ruger Mark IV Break Barrel .177 Cal Pellet Pistolis a low cost target plinker that also doubles as a licensed Replica for that coolness factor so you won’t get an all metal super top quality build here. That said metal and plastics are well used and for sure details in the fit and finish have been improved over the Buck Mark URX version where I found the barrel felt a bit sloppy and the trigger was plastic. The Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistol has a much tighter barrel fit when closed and the trigger is now metal! Maybe Umarex watched my video back in the day and took some notes?
Realism: The Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistol most resembles the Mark IV Hunter edition and is pretty much bang on in terms of being a replica other than the tell tail hinge just under the barrel required for a spring piston design, there really is no way to get around this so I’m not going to criticize this minor difference. The real steel version is almost 3 pounds and so the pellet shooting version is a bit under weight so it would have been to have had more metal perhaps in the barrel and lower frame. Again since the pellet shooting version is a springer you will not have any working bolts or slide catches or a built in magazine.
Pros:
It's a decent Ruger Mark IV Replica!
Feels well built overall.
Expect it to have really good accuracy like the Umarex Browning Buck Mark URX since they share similar mechanical design.
Barrel locks into place much better than the Umarex Browning Buck Mark URX did.
Fully adjustable rear sight with fiber optic front sight.
Auto locking safety, just don’t forget to unlock before each shot
Actual metal trigger in this version.
Nice and compact, not too heavy.
Full Ruger licensed via Umarex.
Fairly low price tag.
Cons:
No built in rail for a sight system like the Umarex Browning Buck Mark URX.
Would have liked a metal trigger and maybe a slightly lighter trigger pull to match the real Buck Mark's very light trigger pull.
A bit more metal would have been nice.
Significantly more expensive than the black version which is the same exact gun in a different color.
Comments: The Stainless Ruger Mark IV Break Barrel .177 Cal Pellet Pistol is a decent looking replica and a decent pellet shooting target pistol and if you own the real steel version in 22LR you may just want to get your hands on one of these Break Barrel Replica Pellet shooters. The only real question is do you get the Stainless version with simulated wood grips or the all black version? If you like the look of the stainless version and don’t care about money whatsoever, then pickup that one up since it is a Limited Edition version that will only go up in value over time. If you are on a budget and don’t mind the look of the all black versions or maybe even prefer it then by all means grab one since at the end of the day they will both perform exactly the same.
My Vimeo Table Top Review Videos for the Umarex Stainless Ruger Mark IV Break Barrel .177 Cal Pellet Pistol:
Type:Airsoft pistol. Distributer:Umarex. Model:Smith & Wesson M&P 9L. Materials: Metal and polymer build. Weight: 1.7 pounds (757 grams). Barrel: 4.75 inches (121mm), non-rifled. Total Length: 8.5 inches (215mm). Propulsion: CO2 x1. Action: Semi auto blowback, single action only Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 15 rounds. FPS: 410 Claimed.
Trigger Pull: The trigger pull on the Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol is fairly light weight being a single action only trigger. There is about a quarter inch of take up with an easy release that is not hitchy at all. You will need to rack the slide to load your first Airsoft BB into the breach and engage the action but on the first shot but then the blowback action does this for you until the Airsoft Pistol is out of ammo and the slide locks back.
Accuracy: I have not performed my Field Test Shooting Video for the Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol so stay posted for that video coming out in the next couple of weeks. Umarex has claimed a velocity of around 410 FPS using .20 gram Airsoft BB’s but that does seem a bit quick, well will have to see when I place some shots though my Chronograph! In terms of accuracy I expect it to shoot about the same as most Full Blowback Airsoft Pistols which generally produces a 1.5 to 2 inch 10 shot grouping from 30 feet out using a semi rested shooting position. Again we will find out when I perform my Field Test Shooting Video for the Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol.
Build Quality: The Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol build quality is fairly decent, fit and finish looks good with not too much slide wiggle and the materials used are both metal and plastic or polymer that look to be good quality. I do expect some of the black finishes ot come off on the high spots as these guns are generally electroplated and not too thick with it but this can actually make the gun look more realistic with that slightly worn in look to it.
Realism: The Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol in terms of looking like the real steel version of its counterpart is very close for sure, it would be hard to tell without really taking a close look t it. Everything about this Replica Pistol works for the most part like the real steel version including most of the mechanical parts like the slide catch release, magazine release, take down lever, trigger safety and you can even fully field strip it which gives you easy access to the hopup on the barrel. Of course the full blowback action really seals the deal in terms of making this gun shoot like a real semi auto pistol.
Pros:
Very accurate replica of the S&W M&P 9L.
Fairly accurate weight and feel to it.
Metal and plastic parts where you find them on the real steel version, fit and finish is good.
Working trigger safety and ambidextrous working slide catch release.
Full size dropout metal magazine that holds Airsoft BB's and CO2.
Warning instructions are discreet under the trigger guard.
Recessed barrel and hidden CO2 screw for more realistic look
Fully Smith & Wesson licensed via Umarex.
Rail for add on accessories.
White dot sights for easy target acquisition.
Comes with three sizes of interchangeable grips S/M/L.
Adjustable hopup so you can at least adjust elevation at range.
Comes in a box rather than a clamshell.
Cons:
Has an orange tip but could be painted black or silver to match.
Sight are not adjustable.
15 round magazine has less capacity than some other blowback Airsoft Pistols.
Comments: The Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol is a nice addition to the Smith & Wesson M&P line of Replica Airguns. I’m glad they made it in full blowback but being Airsoft based that is generally the way they lean towards. Hopefully we get to see 4.5mm Steel BB version too in the future! For now we have it in Airsoft and with the longer barrel perhaps it will shoot a bit hotter than most of the other CO2 Blowback Airsoft Pistols, maybe even 410fps like Umarex claims but I will be surprised if it does. I will be happy to see something in the high 300’s to be honest. No matter what, you now have yet another Smith & Wesson option to consider when looking for your ultimate Replica Airgun!
My Vimeo Videos for the Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol
This time I have a tiny Mystery Box to unpack and show you guys, this time there are only two pistols, one is a Spring Piston Single Shot .177 Caliber Pellet Pistol and the other is a 6mm Airsoft Blowback BB Pistol, both are Licensed Replicas for Umarex. If you want to find out more about each Air Pistol then make sure to watch this Mystery Box Unboxing Preview Video!
This will be my only video this week as I am in what is called Peak Week in preparation for the Vancouver Fall Calssic Fitness show I am competing in this upcoming weekend. Peak Week really takes a lot out of me and is rather time consuming with the physical activity I am doing and daily blog styled videos I am posting for my other channel www.GetFitOver40.com.
If you are interested in what I do fitness wise then checkout that channel and follow me along this week as I hope to kick some but competing against dudes half my age.
Type: AEG Airsoft Rifles Manufacturer:Specna Arms. Model:Core SA-C07-PDW Materials: Fiberglass reenforced plastic and metal/aluminum. Weight: 5.27 pounds ( 2.39 kg). Total Length: 27.2 - 30.3 inches (690 - 770mm). Barrel: 10.63 inch (270) inner 6.03mm tight bore barrel non rifled. Propulsion: AEG. Action: Single action semi & full auto. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: High cap 380 round magazines. FPS: 380 fps with installed spring, included M90 spring will be lower fps.
Trigger Pull: The trigger pull on the Specna Arms Core SA-C07-PDW AEG Airsoft Rifle is similar to a light single action trigger as they are essentially an electrical on off switch. There is a little bit of take up with virtually no extra friction to let you know when the release is going to be, with a bit of use you will figure out exactly when the trigger will release the action.
Accuracy: At this time I have not made my Field Test Shooting Video or even shot the Specna Arms Core SA-C07-PDW AEG Airsoft Rifle, but plan to very soon. You can checkout a previous video where I test out both Specna Arms RRA SA-C10 Core and E10 Edge which should perform similarly to the Specna Arms Core SA-C07-PDW AEG Airsoft Rifle
Build Quality: One thing I can say is no matter which version of the Specna Arms AEG Air Rifles you deicide to go with (either a Core or Edge Series), you are getting extremely good value for your money and neither one is going to have any low quality parts in it. Even the lower cost Core Series will have fiber glass reenforced plastic and metal parts along with a metal gearbox and virtually almost the same build as the more premium and slightly higher priced Edge Series. You will get upgrades in the Edge Series such as a an aluminum receiver and buffer tube, a GATE X-ASR Mosfet, the New Orion Gearbox, deep laser engraved licensing and an additional magazine. All of this for the little bit more you pay for an Edge series Specna Arms AEG Airsoft rifle.
Realism: The Specna Arms Core SA-C07-PDW AEG Airsoft Rifle is based on the AR15 or M16 platform of course in a very modern and PDW styled look. It looks and feels the part for sure with lots of working parts including the safety, selector switch, charging handle, dust cover, adjustable rear stock, pop-up front and rear sights as you would expect. Most of the hardware should be interchangeable with a real steel AR if you want to personalize the look of your Specna Arms Rifle.
Pros:
Super affordable yet very high quality product for what you pay.
Quality components throughout both the Core and Edge series.
Rock River Arms Licensed with hologram on receiver.
ESA™ quick spring change system makes spring changes quick and easy.
Comes with two springs for potential indoor and outdoor usage.
Plastic parts are fiberglass reenforced making them very durable.
Quick release fully adjustable pop-up sights.
No orange tips on our Canada Store versions.
Lots of rial mounting options even on such a short PDW styled AR.
Metal V2 Gearboxes with metal gears and mostly all metal parts inside.
Easy access to motor for any possible trouble shooting you any need to do
Cons:
Plastic receiver.
Need to hold back charging handle to access hop-up.
You will need a very compact battery setup with most Specna Arms models.
Comments:
Value for your money is what comes to mind when I think about the entire Specna Ams AEG Airsoft Riffle product line, especially with the Core series. The Specna Arms Core SA-C07-PDW AEG Airsoft Rifle is probably one of my more favorite versions as I really like PDW style compact AR’s in general. You will have to make sure you have on hand a very compact battery as space is extremely limited but other than that one main downside to this style of AEG everything else about it for the money is bang on and worth any slight compromises.
My Vimeo Table Top Review for the Specna Arms Core SA-C07-PDW AEG Airsoft Rifle:
I have another Huge Mystery Box to open and share with everyone, this one was even larger and heavier than the last one! You are going to have to watch the video to get all the details on what is actually inside but I can say there are 4 AEG Airsoft Rifles from a new to us company called Arcturus in both AR and AK versions and 2 CO2 Non Blowback Replica Pellet Pistols from KWC.
I do have a some more videos to make from the last Mystery Box Preview being a Specna Arms AEG PDW AR Airsoft Rifle and a Paintball Pump Shotgun that I still need to make both Table Top and Field Test Shooting Video for.
Type:Pellet Rifle. Manufacturer: Umarex Model:HK MP7 .177. Materials: Metal and Polymer. Weight: 4.4 pounds (2kg). Barrel: 11.7 inches (29.7cm). Total Length: 31 inches (78.7cm). Propulsion: Break Barrel Spring Piston. Action: Single Action Single Shot. Ammunition Type: .177 Caliber Pellets. Ammunition Capacity: 1. Max FPS: 490 Claimed.
Trigger Pull: The trigger on the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun is single action only requiring you to break the barrel and compress the internal spring piston before you can shoot it. The actual trigger pull is pretty decent overall. There is very little take-up but the creep is on the longer side but fairly smooth requiring medium pressure. The release is a bit hard at first to predict but nothing some trigger time can’t get you use to.
Accuracy: I have not performed any shooting tests with the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun so far. I hope to make that Video Review next week. I expect the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun to perform well in the accuracy department especially with the included Red Dot Optical Scope installed. I hope the velocity rating from Umarex is based on lead pellets and not hyper velocity light weight pellets but we will find out the story when I perform my Field Test Shooting Video shortly!
Build Quality: The Umarex HK MP7 .177 Cal Break Barrel Pellet Gun is a China made Airgun but looks to be well made. It has lots of metal parts as you would expect from a Spring Piston Rifle which adds a nice weight and feel to it. I did however have an issue with the front plastic mock Suppressor/Compensator as it does not seem to be attached to the metal barrel very well other than being pressure fit which is not going to cut it with all the vibration a spring piston system makes. My first shot loosened the mock Suppressor/Compensator so I will either have to hold it when shooting or find another way to make sure it stays in place.
Realism: The Umarex HK MP7 .177 Cal Break Barrel Pellet Gun is kind of unique in this department as most break barrel rifles are not Replicas, especially the more compact sub machine gun styled ones. Umarex did good job making the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun look like a real HK MP7 for the most part. Of course it is a Spring Piston Rifle at its core so exceptions had to be made to make this work including molded non working parts like the magazine release, sector switch and, bolt/ejection port. That said all in all it is a decent looking replica considering it is a Break Barrel Airgun under the skin.
Pros:
Not many Replica Pellet Rifles on the market, especially in a more compact gun.
Comes with Red Dot sight.
Lots of rails for adding accessories to it.
Full HK Licensed by Umarex.
Collapsible Wire Stock.
Nice high claimed 490 fps.
No need for CO2 so low cost to cooperate.
Not effected by temperature like a CO2 Airgun.
Should have better accuracy than most BB Replica Airguns.
Very solid feel to it, good overall weight and feel.
Cons:
Not going to be an action shooter, have to reload after each shot.
A good overall Replica but not as Realistic or full operation as a BB version would be.
Mock Suppressor/Compensator poorly attached to barrel.
Comments: The Umarex HK MP7 .177 Cal Break Barrel Pellet Gun is an interesting product, on one hadn't it is a Replica Airgun and most people expect a Replica Airgun to have all of the appropriate working parts similar to what would be found on the real steel version. But since this is a Break Barrel Airgun at the core the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun will not function the same as the Real Steel version so as long as you don’t expect it to and appreciate the fact that it should be a nice accurate low cost to operate target rifle then I think you will understand this product and enjoy it for what it is… A Single Shot Pellet Rifle that looks a lot like a HK MP7.
Type: BB Rifle. Manufacturer: Crosman. Model: ST-1. Materials: Metal & plastic. Weight: 6.07 pounds (2.75 kilograms). Total Length: 17.75/33 inches (Pistol/Rifle). Barrel Length: 15.5 inches. Propulsion: 12 gram CO2 dual cartridges. Action: Blowback - single action only. Ammunition Type: 4.5mm steel BB's. Ammunition Capacity: 25 Round/Spring - 300 Round/Hopper. FPS: 480fps. Rate of Fire: 1400 rounds per minute in full auto
Trigger Pull: The trigger pull on the Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun is single action only since the right side charging handle must be cocked first before you can shoot it to engage the action. The trigger is short and fairly light but not overly light. The real fun happens with the Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun when you switch it over to full auto mode and with just one pull and hold of the trigger you empty the 25 round magazine in a mere matter of seconds at 1400 rounds per minute.
Accuracy: I have not actually shot this BB Rifle to date but expect it to get similar results to the other Crosman Full Auto BB Machine guns I have already reviewed. I am expecting a bit more velocity with the longer barrel extension installed and would be happy if I was able to get in the mid 400’s. Accuracy should also be about the same with 1 inch semi auto groups from 30 feet out expending a bit when in full auto.
Build Quality: The Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun is well made all around. Weighing in at 6.07 pounds without any add on accessories other than the included compact Red Dot sight. It feels solid and well built. There is a lot of metal going on inside and out of this rifle but keep in mind the top and bottom receiver are plastic with metal parts where they need to be like in the internals, pretty much all the working parts are metal, the magazine is full metal, the buffer tub is metal, charging handle, selector switch, magazine release, bolt release, trigger and of course the barrel is metal.
Realism: The Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun is not modeled after any real steel gun I know of. It resembles a futuristic weapon you would see in a SciFi Action Movie or Alien First Person Shooter. I was not a fan of it when it was first released by Crosman but after seeing and holding it in person it is growing on me quickly.
Pros:
Very unique, not like your regular Replica Rifles, very futuristic in design.
Drop out magazine doubles as the 300 round hopper and holds CO2 and BB’s.
Comes with Red Dot Sight and lots of rails for mounting what every you want on it.
Can be either a Pistol or Rifle or a PDW by adding or removing the Barrel Extension and Rear Stock.
Barrel Extension actual lengthens the barrel and should increase fps, not just for show!
Tactile comfortable rubber padding in multiple locations.
Semi auto and full Auto selectable.
Expected higher fps of up to 480.
Cons:
Some people may not like the look? Not like your normal modern rifle.
Front rubber grip comes off really easy at least on mine?
Will require barrel extension for full velocity.
Comments:
The Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun is a brave move by Crosman, I was not expecting something like this from them and when I originally saw it I was not sure if it was a good idea or not but again once seeing it in person and actually holing it I feel a lot better about it. It will for sure appeal to those looking for a futuristic Airgun or wanting something that looks like a gun from a video game or SciFi movie. I also like the versatility you have with the Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun being able to configure it how you like either as a Pistol, full on Rifle or PDW style shooter.
My Table Top Video of the Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun:
As the title suggest this a video about a Huge Mystery Box so I am not going to say what’s in it, I can say that their are 4 main products mostly rifles per-say. One is a Futuristic Full Auto BB Rifle, one is a Paintball Shotgun, One is an AEG Airsoft Rifle and one is a Replica Break Barrel Pellet Rifle.
So I have a lot of variety here to show everyone! I did absolutely zero research on any of the products I show in this video since like you I had no real idea what was inside other than how many and that most where rifle based.
Enjoy finding out what new products I will be reviewing over the next month with dedicated Table Top and Field Test Shooting videos.
Sights for guns in general are the same for Airguns as is with real steel guns for the most part and can be mixed and matched with a couple of exceptions. Spring piston rifles for instance are an exception because of the unique vibration the spring makes and how it can damage a standard optical sight, so in this case you’re best to use an optical sight designed for a spring piston Airgun. In most other cases sights can be used on all types of guns.
In this Airgun Sights video I will go over the various types of sights that either come as part of the gun design or can be added afterwards using a rail or mounting system.
Types of Airgun Sights most commonly used.
Iron Sight (Fixed or removable).
Iron Sight (Adjustable).
Iron Sight (White Dot, Fiber Optic).
Come in Post/Notch, Post/Aperture (Peep).
Common on Pistols and Rifles
Laser Sight:
Generally added to a rail or can sometime be integrated into the design of the gun.
Common on both Pistols and Rifles.
Red DotandHolographic:
Generally not magnified.
Most common on Rifles but can be used on Pistols.
Optical Magnified (Telescopic)
Come in a variety of magnifications for different shooting ranges.
Gun Safeties generally are going to be similar for all types of guns, so Safeties used with Airguns are often the same types as used with Real Steel Guns. Some guns will have no Safeties at all while other guns many have multiple Safeties on them. In this informative video I go over six of the more common types of Gun Safeties used in Real Steel Guns and Air Guns.
Here is a list of the more common types of gun Safeties.
I sometimes mention in my review videos that a gun is either Full Blowback or Partial Blowback and some people may not understand exactly what this means and how it effects the Airguns Blowback Action and Performance so I figured it would be best to make a dedicated video talking about the differences and also some of the Pro’s and Con’s of each type of Blowback Action.
In the video I obviously go into a fair amount of detail and show you around each type of Airgun and Magazine as they do differ a fair amount but to summaries for you here in this written form, the main difference is going to be how much the slide moves back and forth. With Full Blowback Airguns the slide will move much longer back and forth on the frame of the Airgun much like a real gun does and the slide Catch/Lock generally locks back further too. With a Partial Blowback Airgun the slide generally has a shorter range of movement back and forth on the frame with the slide locks usually about half of the distance compared to a Full Blowback Airgun.
The magazines are also very different as a Full Blowbacks Airgun generally has a partially exposed BB which is pushed into the barrel by the nozzle with each slide cycle. With a Partial Blowback Airgun the BB is generally not exposed and either the trigger action or simply the CO2 force is required to transfer the BB in the breach of the Airgun.
Another point to mention is that Full Blowback Airguns tend to use more CO2 and have a slightly lower velocity as compared to Partial Blowback Airguns but this is not a rule.
There are many types of magazines used in Airguns and some of this is dependent on the ammunition used.
For instance a stacked type of magazine often used for Steel BB and Airsoft can not be used for Pellets as pellets tend to deform when stacked in such a way since there is no metal casting protecting them from mashing into each other.
So what type of magazines do we generally see in Airguns? The most common Airgun magazines are as follows:
Simple Stick Magazine
Mostly used with Steel BB but also found in some Airsoft Airguns.
Some Pellet Airguns use a type of stick magazine with a rotary magazine on each end.
Used in non-blowback and blowback Airguns.
Can be made from plastic or steel or a combination of both materials.
Full Size Drop Out Magazine
Used with Steel BB and Airsoft guns.
Generally you will find these types magazines hold both the BB’s and CO2.
Used in non-blowback and blowback Airguns.
Commonly used with Airsoft Rifles in mid to high capacity.
Can be made from plastic or steel or a combination of both materials.
Rotary magazine
Used with Steel BB, Airsoft and Pellet Airguns.
Used in non-blowback and blowback Airguns.
Can be made from plastic or steel.
Can often use mixed ammo types as in both 4.5mm Steel BB and .177 caliber pellet.
Belt Fed Magazine
Like rotary magazine belt fed magazine can accommodate Steel BB, Pellet and Airsoft but are most often used with Pellet Airguns.
Usually found in a full size magazine that also holds the CO2.
Used in non-blowback and blowback Airguns.
Can be made from plastic or steel or a combination of both materials.
Internal Magazine
Used with Steel BB, Airsoft.
Can have a hopper built in hat feeds a spring fed magazine.
Usually found in lesser expensive Airguns but not a rule.
In this Video I go through each type of Airgun Magazine and talk about their differences and uses.
I have another Full Auto Fun Video this one focusing on 4.5mm Steel BB Versus 6mm Plastic and which one is better in terms of accuracy and shredding power. I perform this super scientific test by shooting obviously in full auto two comparable Steel BB and Plastic Airsoft Rifles at a paper target setup 20 feet away with a magazine as a backer so I can see what the accuracy is like and how much of the paper magazine gets shredded by each ammo being tested.
I have split this video into three separate videos, in video one I compare two similar AR styled rifles, a CO2 powered Blowback 4.5mm BB Rifle to a Gas Blowback 6mm Airsoft Rifle. In video two I compare two AK type Blowback Rifles to each otters, again a CO2 4.5mm Steel BB along with a Gas 6mm Airsoft.
And lastly in Video three I compare my top picks for each category which include a non-Blowback CO2 4.5mm BB Machine gun to an AEG 6mm Airsoft Rifle.
I have another Full Auto Fun Video this one focusing on 4.5mm Steel BB Versus 6mm Plastic and which one is better in terms of accuracy and shredding power. I perform this super scientific test by shooting obviously in full auto two comparable Steel BB and Plastic Airsoft Rifles at a paper target setup 20 feet away with a magazine as a backer so I can see what the accuracy is like and how much of the paper magazine gets shredded by each ammo being tested.
I have split this video into three separate videos, in video one I compare two similar AR styled rifles, a CO2 powered Blowback 4.5mm BB Rifle to a Gas Blowback 6mm Airsoft Rifle. In video two I compare two AK type Blowback Rifles to each otters, again a CO2 4.5mm Steel BB along with a Gas 6mm Airsoft.
And lastly in Video three I compare my top picks for each category which include a non-Blowback CO2 4.5mm BB Machine gun to an AEG 6mm Airsoft Rifle.
I have another Full Auto Fun Video this one focusing on 4.5mm Steel BB Versus 6mm Plastic and which one is better in terms of accuracy and shredding power. I perform this super scientific test by shooting obviously in full auto two comparable Steel BB and Plastic Airsoft Rifles at a paper target setup 20 feet away with a magazine as a backer so I can see what the accuracy is like and how much of the paper magazine gets shredded by each ammo being tested.
I have split this video into three separate videos, in video one I compare two similar AR styled rifles, a CO2 powered Blowback 4.5mm BB Rifle to a Gas Blowback 6mm Airsoft Rifle. In video two I compare two AK type Blowback Rifles to each otters, again a CO2 4.5mm Steel BB along with a Gas 6mm Airsoft.
And lastly in Video three I compare my top picks for each category which include a non-Blowback CO2 4.5mm BB Machine gun to an AEG 6mm Airsoft Rifle.
For this Video 2 Accuracy Test I shoot all of the above listed Airguns at a paper target setup 30 feet down range using a semi rested shooting position with my hands resting on a sand bag up front and seated on a stool in the back. It’s not perfect but works well enough. I didn’t take a ton of time with each gun since there where 4 to shoot in this Field Test Shooting Video so accuracy may have been a bit better if I took a little more time with each gun.
In Video 2 I test the power and penetration of each Airgun option shooting at a pop can, a soup can and a toilet paper roll so make sure to watch that video if you have not already watched it.
For this Video 1 Power Test I shoot all of the above listed Airguns first at a pop can, then a soup can and then a toilet paper roll. The ides is to test penetration abilities with the pop and soup can and then raw force shooting the toilet paper as it will absorb all the energy from each airgun round and by gauging how much the toilet paper reacts or moves it should tell us which airgun has the most raw power or energy.
In Video 2 I will be testing accuracy using my standard 30 round paper target setup in the Replica Airguns Sea Can so stay posted for that upcoming video shortly…
Type:Airsoft Rifle. Manufacturer: Tokyo Marui. Model:CQBR Block1. Materials: Metal and Polymer. Weight: 9.97 pounds (4.52kg). Barrel: 9.84 inches (250mm). Propulsion: Gas Blowback. Action: Semi & Full Auto - SAO trigger. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: 35 Max FPS: 350 Tested (.20 gram).
Trigger Pull: The trigger on the Tokyo Marui CQBR Block1 GBB Airsoft Rifle is single action only so the charging handle will need to be engaged on your first shot un less the bolt is already back for a preview empty magazine and reload. The trigger is light and short with virtual no makeup but then just a bit of creep before releasing the internal striker and firing a round.
Accuracy: I did already perform my Field Test Shooting Video for the Tokyo Marui CQBR Block1 GBB Airsoft Rifle so I do have some information to share relating to the shooting abilities of this Gas Blowback Airsoft Rifle. During my Velocity Chronograph Test I was able to average 332 fps using .20 gram Airsfot BB’s with my highest velocity shot hitting 350 fps. My 10 shot grouping at 30 feet away yielded a 1.5 inch spread and when I placed the Tokyo Marui CQBR Block1 GBB Airsoft Rifle in full auto it did open up a fair amount since the blowback action really rocks this gun around a lot making full auto shooting spread out much monroe than semi auto shooting but still so much fun to shoot in full auto :). You can watch my full Field Test Shooting Video here!
Build Quality: The build quality of the Tokyo Marui CQBR Block1 GBB Airsoft Rifle is one of the highest out there with high quality metal parts throughout this GBB AIrsfot Rifle both inside and out. Some of the internals include a heavy duty 19mm blowback piston, New mechanism Z-system to prevent wear and tear of bolt catch, piston absorber and friction relief bolt roller to reduce the burden on internal parts due to bolt operation.
Realism: The Tokyo Marui CQBR Block1 GBB Airsoft Rifle is a near perfect replica of a Colt licensed AR 15 and Tokyo Marui has a ton of detail to the fit and finish including the unique and multiple finishes on the external parts: The rail hand guard, front sight, and stock reproduce the difference in FDE color tone applied to each part as in the real thing. The metal rail hand guard reproduces the color by alumite treatment with excellent scratch resistance. In addition, the upper / lower frame and bolts are made of Ceracoat, which has a strong coating film and excellent scratch resistance.
Pros:
Super high quality GBB Airsoft Rifle.
Bolt locks back for easy hop-up adjustments.
Very heavy blowback operation.
Lots of metal parts, mostly everything except the stock, fore grip and pistol grip.
Lots of mounting points with it’s quad rail setup.
Awesome internals: Heavy duty 19mm blowback piston, New mechanism Z-system to prevent wear and tear of bolt catch, piston absorber and friction relief bolt roller to reduce the burden on internal parts due to bolt operation.
Attention to detail goes beyond expectation! Color reproduction and special surface treatment is a good example of this.
Easy to mount a sling with it’s QD tactical sling mounts on handguard, lower receiver, and stock.
Adjustable hop-up as expected.
6 portion rear stock.
Removable and fully adjustable rear sight.
Great for close and mid range shooting situations with a 350 average fps using .20 gram BB’s.
Accuracy was good at 30 feet getting around a 1.5 inch 10 shot grouping.
Cons:
My magazine did not seem to seal very well in the nozzle area when filling with propane but mag seemed to fill OK, just seemed to waste a bit of gas while filling.
Heavy blowback makes full auto accuracy move around a fair amount.
Pretty much have sue the included magazine filling tube to load BB’s in the magazine sop will need ot be carried with you in a game.
On the very high end of the price spectrum.
Comments: I am a bit of a sucker for Blowback Airguns in general whether it be Pistol, Rifle, BB, Pellet, Paintball or Airsoft. So right out of the box I loved the Tokyo Marui CQBR Block1 GBB Airsoft Rifle with its heavy blowback recoil. All that aside the Tokyo Marui CQBR Block1 GBB Airsoft Rifle is one of the highest quality Gas Blowback AR 15 type Airsoft Rifles you will be able to get your hands on assuming if you can find it in stock. It is a near perfect Airsoft Replica of a real steel Colt AR with only the best finishes and parts available for such a GBB Rifle.
Type:Airsoft Rifle. Manufacturer: Sig Sauer Model:ProForce MCX Virtus. Materials: Metal and Polymer. Weight: 7 pounds (3kg). Barrel: 11.6 inches (295mm). Propulsion: AEG. Action: Semi & Full Auto - SAO Electronic trigger. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: 120 (Mid cap). Max FPS: 408 Tested (.20 gram).
Trigger Pull: The trigger on the Sig Sauer ProForce MCX Virtus AEG Airsoft Rifle is essentially a Single Action Only electric on off switch that can allow for semi and full auto shooting along with a safety position based on the sector switch position. Because of this it is fairly short and light weight. There can be a slight delay from the time you pull the trigger to when the BB is released as since the electric motor needs to first pull back the internal spring before being released. A higher voltage battery will shorten the time between your trigger pull and the Airsoft BB release. Higher voltage battery also increases the full auto cycle rate.
Accuracy: I did already perform my Field Test Shooting Video for the Sig Sauer ProForce MCX Virtus AEG Airsoft Rifle so I do have some information to share relating to the shooting abilities of this AEG Airsoft Rifle. During my Velocity Chronograph Test I was able to average 408 fps using .20 gram Airsfot BB’s, that was using the out of the box installed 120 spring. In terms of accuracy, my 10 shot grouping at 30 feet away yielded a 1.5 inch spread and when I placed the Sig Sauer ProForce MCX Virtus AEG Airsoft Rifle in full auto it did not open up that much more, only to around 2 inches since there is virtually no recoil to throw off full auto shot placement. You can watch my full Field Test Shooting Video here!
Build Quality: The build quality of the Sig Sauer ProForce MCX Virtus AEG Airsoft Rifle is exceptional with high quality material inside and out, this Airsoft Rifle is mostly metal with a CNC machined receiver and a hefty 7 pound weight to it. Internally you will find VFC Avalon Gearbox featuring improved bearings, quick change spring system, built in MOSFET, and powered by high torque neodymium magnet motors.
Realism: The Sig Sauer ProForce MCX Virtus AEG Airsoft Rifle is designed and licensed by Sig Sauer to be as close to their real steel version of the MCX Virtus as possible in every way. As expected you will find Sig Sauer and Virtus licensing all over, size, handling and weight are also true to the original.
Pros:
Super high quality AEG Airsoft Rifle.
Bolt locks back for easy hop-up adjustments.
Sig Sauer designed and licensed.
Lots of metal parts including the CNC machined metal receiver, rear stock guide rails and most mechanical moving parts.
Lots of mounting points with it’s full length picatinny top rail with M-LOK handguard.
Awesome internals, VFC Avalon Gearbox, quick change spring system, built in MOSFET, high torque neodymium magnet motors.
Easy to mount a sling with it’s QD tactical sling mounts on handguard, lower receiver, and stock.
Performed well in the Field test hitting close to claimed fps and easily shooting a 1.5 inch 10 shot group for 30 feet away.
Cons:
No included sights so you will need to add your own iron, red dot or optical sight.
Battery area is a bit tight so you will need fairly compact batteries.
Comes with orange flash hider but can be swapped out.
On the high end of the price spectrum.
Comments: The Sig Sauer ProForce MCX Virtus AEG Airsoft Rifle is not only a looker but also a performer and is one of the higher quality AEG AR Styled Airsoft Rifles out there. I know there are a ton of AR AEG Airsoft Rifles to pick from but if you want something a little bit different then the rest than the Sig Sauer ProForce MCX Virtus AEG Airsoft Rifle is for sure one to look at. It is a bit more money up front but will offer exceptional performance and the high quality internals will not only perform well but will last the test of time saving you money long term.
