Entries in Airsoft,Rifle

SHOT Show 2020 Las Vegas Teaser Video

No Comments

Here we go again, another round of SHOT Show videos brought to you direct from Replica Airguns!

As always I like to start off with a Teaser Video with a few quick clips of some of the new products I had the opportunity to take a look at at this years SHOT Show 2020 Las Vegas.

I will be rolling out Interview Videos as quickly as I can edit them and put them together for the following Airgun Related companies:

  • Sig Sauer

  • Umarex

  • Crosman - Velocity Outdoors

  • ASG

  • Air Venturi

  • Chiappa

So sit back and enjoy this years Replica Airguns SHOT Show 2020 Las Vegas Teaser Video!

Categories: .22 cal, 4.5mm / .177 cal, 6mm, Airgun News, Airsoft, Airsoft News, BB, Blowback, Bulk Air, CO2, Full Auto, Gas, GBB, Nerf High Impact Round, PCP, Pellet, Pistol, Pump, Replica Airguns News, Revolver, Rifle, Semi Auto, Single Shot, Spring Piston, YouTube Video Tags: SHOT Show, SHOT Show 2020, Umarex, ASG, Crosman, AirVenturi, Sig Sauer, Chiappa

Umarex Legends Cowboy Rifle Versus Daisy Red Ryder BB Rifle Shooting Comparison

No Comments

I have not officially done a Field Test Shooting Video for the Umarex Legends CO2 BB Lever Action Cowboy Rifle other than my quick outside shooting test where I simply shot a bunch of rounds at some pop cans just to see how the Umarex Legends CO2 BB Lever Action Cowboy Rifle would work for me and it did perform well during that test.

Jumping ahead to a little while later when I went to make my Official Field Test Shooting Video for the Umarex Legends CO2 BB Lever Action Cowboy Rifle. I found it was not performing well at all, shooting well under the 410 claimed fps closer to 200 fps which was a surprise since it seemed to do a lot better for me on my previous test. I even changed out the CO2 but still did not get any better results. I racked this up to maybe being a defective gun and so I went about getting my hands on another Umarex Legends CO2 BB Lever Action Cowboy Rifle.

Guess what? Same thing with rifle number two. Very poor fps, again almost half of the claimed rated velocity. So at this point I decided I was goring to make the Field Test Shooting Video for the Umarex Legends CO2 BB Lever Action Cowboy Rifle and let the results speak for themselves… I also thought it would be fun to compare it to the Classic 1938 Daisy Red Ryder BB Gun since I figured they would both get similar fps and accuracy and be rather comparable at the end of the day.

I do have to say that the Umarex Legends CO2 BB Lever Action Cowboy Rifle did make me eat my words and I am happy it did since I really like the Umarex Legends CO2 BB Lever Action Cowboy Rifle and wanted it to do well!

Usually I state all there results for My Field Test Shooting Videos here in the written article but I kind of feel it is best if you just watch this one from start to finishes since the video result s did turn out to really surprise me in the end.

Categories: 4.5mm / .177 cal, BB, CO2, Comparison, Field Test, Repeater, Review, Rifle, Spring Piston, YouTube Video Tags: Umarex, Legends Cowboy Rifle, Daisy, Red Ryder

Replica Airgun Favorite Picks of 2019

No Comments

We had a lot of great new Airguns that I reviewed this year at Replica Airguns. Some of them really stood out to me and so I made a video showing my Favorite Replica Airgun Picks of 2019. Of course there where many other Airguns that could has just as easily made this video but I had to draw the line somewhere and pick the ones that in my opinion where the best of 2019. Make sure to watch my Vimeo video where I go into some more details on why I liked each Airgun.

Below is a list of the top Replica Airgun Picks of 2019:

Pellet Rifles:

BB Rifles:

Airsoft Rifles:

Pellet Pistols:

Airsoft Pistols:

Paintball Guns:

Blank Guns:

BB Pistols:

Categories: .43 cal, 4.5mm / .177 cal, 6mm, 9mm, Airsoft, BB, Blank Gun, Blowback, Break Barrel, CO2, Comparison, Full Auto, Gas, GBB, Paintball, Pellet, Pistol, Repeater, Review, Rifle, Semi Auto, Spring Piston, YouTube Video Tags: Umarex, Glock, KWC, Crosman, SIG Sauer P365, AirVenturi, Tokyo Marui, ROHM

Tokyo Marui Hi-Capa 5.1 D.O.R GBB Airsoft Pistol Table Top Review

1 Comment

Type: GBB AIrsoft Pistol.
Manufacturer: Made by Tokyo Marui.
Model: Hi-Capa 5.1 D.O.R.
Materials: Mostly polymer with metal components.
Weight: 1.85 pounds (839 grams).
Barrel: 4.4 inches (112mm) metal non-rifled.
Propulsion: Green gas.
Action: Semi auto blowback, single action only trigger.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 31 round drop out full size metal magazine.
FPS: Claimed 365.

Trigger Pull: The single action only trigger pull on the Tokyo Marui Hi-Capa 5.1 D.O.R GBB Airsoft Pistol is extremely nice, there is virtually zero take-up with a light and easy release. You can really hammer out quick shots with this Airsoft pistol. Other than the Tokyo Marui Strike Warrior .45 1911, one of the best 1911 triggers I have tested so far.

Accuracy: At this point I have not shot the Tokyo Marui Hi-Capa 5.1 D.O.R GBB Airsoft Pistol so I have no idea what the actual fps is and how accurate it will be but based on the reputation of Tokyo Marui Airsoft guns I have high expectations from the Tokyo Marui Hi-Capa 5.1 D.O.R GBB Airsoft Pistol when I perform my Field Test Shooting Video.

Build Quality: The Tokyo Marui Hi-Capa 5.1 D.O.R GBB Airsoft Pistol on the outside it is mostly all plastic (Slide and portion of the frame). That said the quality is fantastic, fit and finish is top notch everywhere and you will find metal parts where they need to be as in the inner and outer barrel, trigger, hammer, slide catch release, back strap safety, trigger group, magazine and many more internal parts.

Realism: The Tokyo Marui Hi-Capa 5.1 D.O.R GBB Airsoft Pistol is built on the Colt 45 1911 design but is obviously a more modernized and tacticle version of the classic 1911. The only factor that separates the Tokyo Marui Hi-Capa 5.1 D.O.R GBB Airsoft Pistol from that of a traditional 1911 in design is the lack of a barrel bushing which kind of makes field stripping and access to the Airsoft guns intervals a little bit easier. You still get that 1911 feel and awesome Single Action Only Trigger with your thumb safety and slide catch release in all the familiar places. Of course the Grip safety works as you would expect on a 1911.

Pros:

  • Light and crips flat faced SAO trigger feels great.

  • Fit and finish is excellent, next to zero slide wiggle.

  • Very cool looking tactical modernized 1911.

  • Direct Optic Ready removable rear sight to accommodate for included red dot mounting plates.

  • Optional under-rail plate included.

  • Full size high capacity 31 round double stack metal magazine.

  • Ambidextrous thumb safeties.

  • Working grip safety as you would expect on a 1911 based gun.

  • Most mechanical parts work just like a real steel 1911 and can be easily field stripped to access the hop-up.

  • Super fast blowback action, great for quick action shooting.

  • Decent 1.85 pounds weight considering much of the Airsoft gun is plastic.

Cons:

  • Mostly all plastic build.

  • Does not have the barrel bushing found on traditional 1911’s.

  • No white dots on rear sight.

Comments:

So far I have reviewed three of the Tokyo Marui Airsoft pistols and all three have impressed me. Even with a mostly plastic build at least externally in the slide and frames, these Airsoft Pistols still feel and shoot great even if they are a little on the light side. That may be a plus for some people who want a nice light weight side arm that is not weighing them down on the field. The plastic slides really cycle fast and are super snappy, when combined with short and light tirggers you can pop off rounds amazingly fast and on target. For the price I really think any of the Tokyo Marui Airsoft Guns would be a great choice. I do however have a soft spot for 1911’s and so for me the Tokyo Marui Hi-Capa 5.1 D.O.R GBB Airsoft Pistol would be my choice out of the three I have reviewed so far.

Categories: 6mm, Airsoft, Blowback, Gas, GBB, Pistol, Review, Semi Auto, YouTube Video Tags: Tokyo Marui, Hi-Capa 5.1 D.O.R.

Air Venturi TR5 .177 Caliber Pellet Rifle Field Test Review

No Comments

In a way I have already Field Tested the Air Venturi TR5 .177 Caliber Pellet Rifle, well at least in the Baikal version. The Air Venturi version is pretty much a knock of of the Baikal IZH MP-61 which not only look a lot alike but also performed very similarly for me, checkout my Baikal YouTube Video Review for comparison. All that said we can not get Baikal products here in North America anymore so it’s great that Air Venturi has recreated a very similar product for us to have in Canada and the US.

Moving on to the Field Test Review for the Air Venturi TR5 .177 Caliber Pellet Rifle, I first placed 5 shots through my Chronograph to see if the Air Venturi TR5 .177 Caliber Pellet Rifle did in fact shoot around 500 fps and in fact I was able to get all 5 shots up and over 500 fps averaging around 513 fps. Still within our Non-regulated firearm laws here in Canada since we where still under the 4.2 foot pound energy limit using 6.9 grain pellets.

When it came to accuracy I would have liked to have tested out the Air Venturi TR5 .177 Caliber Pellet Rifle over a longer range but in my Sea Can I have a max 30 feet range limit which does give us a decent idea on what to expect for the Air Venturi TR5 .177 Caliber Pellet Rifle. I again shot 5 rounds using the Air Venturi TR5 .177 Caliber Pellet Rifle into my paper target since it has a 5 round magazine. I am not the best springer shooter but I think I did OK as I was able tonged a 1 inch grouping from the Air Venturi TR5 .177 Caliber Pellet Rifle, with 4 of the rounds all within a half inch of each other.

As mentioned before when I shot the Baikal IZH MP-61 I was able to get very similar results but I did have an optical scope on the Baikal IZH MP-61 as compared to the Air Venturi TR5 .177 Caliber Pellet Rifle where I just used the open sights. In my opinion the Air Venturi TR5 .177 Caliber Pellet Rifle is good value for your money offering a unique design with excellent performance and getting as much power out of a pellet rifle as you can get here in Canada without requiring a firearms license.

Pick one up in our Canada or US Online Replica Airguns stores!

Categories: 4.5mm / .177 cal, Break Barrel, Field Test, Pistol, Review, Rifle, Spring Piston, YouTube Video Tags: AirVenturi, TR5

TR5 Pellet Rifle - Schofield No. 3 BB-Pellet Revolver - RG-88 Chrome Blank Pistol Unboxing Preview Video

No Comments

Here we have three very different products I Unbox and Preview for everyone. A Spring Piston multi-shot .177 Caliber Pellet Rifle, a single action BB/Pellet revolver that’s not a Colt! And a really nice looking Semi Auto Blank Pistol in a Chrome finish.

Let’s start with the Air Venturi TR5 Spring Piston 5-shot .177 Caliber Pellet Rifle. I think this is a really well thought out Air Rifle. It’s “almost a Bullpup” in design but it does actually load in front of the trigger just a bit, that said most of the spring piston is behind the trigger setup making it really compact yet with a longer than normal barrel compared to regular Break Barrel Spring Piston Air Rifles. The Air Venturi TR5 Spring Piston 5-shot .177 Caliber Pellet Rifle also has a side lever cocking mechanism along with a 5 round auto indexing magazine which makes it much quicker to cock and reload for fast follow-up shots, again compared to a standard Break Barrel Air Rifle, not to mention no barrel droop! The Air Venturi TR5 Spring Piston 5-shot .177 Caliber Pellet Rifle has a claimed fps of up to 500 so we are getting the max amount of velocity possible for our Canadian laws without making it a regulated firearm and requiring a PAL license. And by the way the Air Venturi TR5 Spring Piston 5-shot .177 Caliber Pellet Rifle does come in both a Lime Green and all Black version just in case you are not a fan of the Lime Green finish I show in this video.

Moving onto the Schofield No. 3 BB/Pellet 6 Shot Revolver Replica, if you like single action revolvers then take a look at the Schofield No. 3 BB/Pellet 6 Shot Revolver Replica. It’s a lot more bulky than a Colt Single Action Revolver and also has that top Break design that makes reloading quick and easy. The version we are selling inner Replica Airgun Online Store is the kit version that comes with 6 BB shells and 6 pellet shells so you can take your pick on ammo types. The barrel is not rifled so Steel BB’s will not hurt the Airgun and since pellets are skirted they do not need a rifled barrel to fly straight and true. You can expect around 445 fps for the Schofield No. 3 BB/Pellet 6 Shot Revolver Replica.

Last up is one of my favorite Blank firing Semi Auto Pistols which I have already full reviews in the all Black version so checkout those Video Reviews for more info on the ROHM RG-88 line of Front Firing 9mm Blank Pistols. All I really wanted to show you guys with the ROHM RG-88 9mm PAK Blank Pistol in Polished Chrome is how awesome it looked with the Polished Chrome finish and that we do have more choices now than we use to have in terms of what finish you can get your ROHM RG-88 in. Personally I like the Polished Chrome finish the best but you can also get it in all Black and Matte Chrome, so you decide which one you like the best.

Categories: 4.5mm / .177 cal, 9mm, BB, Blank Gun, CO2, Pellet, Pistol, Repeater, Review, Revolver, Rifle, Semi Auto, Spring Piston, YouTube Video Tags: AirVenturi, TR5, Schofield No. 3, ROHM, RG-88

Umarex T4E HDS Paintball Shotgun and Diana Bandit - Chaser Pellet Pistol Unboxing

No Comments

In this Unboxing Preview video you really can’t get too much different in terms of product types. First up I showcase the Umarex T4E HDS Double Barrel .68 caliber CO2 Paintball Shotgun. I then take a look at the Diana Bandit PCP and Diana Chaser CO2 Bolt Action Match Grade .177 Caliber Pellet Pistols.

The Umarex T4E HDS Double Barrel .68 caliber CO2 Paintball Shotgun is a two shot short barrelled that could come in handy for CQB engagements but it looks to be designed also as a none lethal home defence weapon since you can load a CO2 without piercing it but when in a bind you simply hit the CO2 screw and it pierces the CO2 activating the gun for instant use. I will have to test this one out to see if it really has enough power to stop an intrude, after all you only get two shots so they better count!

And then we have two Diana Match Grade CO2 Bolt Action Pellet Pistols, both has a similar bolt, sights, barrel and trigger setup but with the Diana Bandit you get a wooden grips, an included 10 shot rotary magazine and it’s PCP powered so you will need a compressor or a pump to use it. The Diana Chaser on the other hand is CO2 powered, has a plastic pistol grip and does not include the 10 shot rotary magazine but you can buy it later on if you get bored loading one round at a time into the breach. I expect both of these pistols to be tack drivers!

The Umarex T4E HDS Double Barrel .68 caliber CO2 Paintball Shotgun is available in both our Canada and US Online Replica Airgun Store while Both Diana Pellet Pistols can only be found in our Canada Store.

Categories: .68 cal, 4.5mm / .177 cal, CO2, Paintball, PCP, Pellet, Pistol, Review, Rifle, Single Shot, YouTube Video Tags: Umarex, T4E HDS, Diana, Bandit, Chaser

2019 Replica Airguns Halloween Contest Giveaway

No Comments

There are two parts to they video, the Halloween Costume Contest and what’s going on next week so make sure to watch it all…

Part 1 - 2019 Replica Airguns Halloween Contest Giveaway

Contest Rules:

  • Must be 18+ to receive a prize.

  • Canada & US winners only.

  • Halloween Costumes must have a weapon of some sort in them.

  • Must post a Halloween costume video to your YouTube channel.

  • Your video must be named "2019 Replica Airguns Halloween Contest Giveaway".

  • November 9th is the deadline date for you to get your video in.

  • Must post a comment in this video letting me know you have a video for me.

  • Must be a subscriber to the Replica Airguns channel.

  • Must like this video

1st, 2nd and 3rd Prizes Awarded:

What’s going on next week?

I will be away competing in a Body Building Fitness Contest so there will not be any more videos that week.

You may have noticed I have been withering away this past couple of months. This is in preparation for a Fitness Contest I am going into. For a show like this you need to be super lean to be competitive.

I have been competing since 2015 mainly in Men’s Physique and have qualified myself over the years to compete at the National level in Amateur Body Building.

The competition I am going to is the GNC / ALLMAX Canadian National Pro Qualifier in Toronto. If I do really well I can possibly get an IFBB Pro Card. Getting an IFBB Pro Card means I would now be able to compete in Pro Body Building competitions.

In order to win the Pro Card I would need to win my hight class and then win the overalls against the other winners in their hight class.

To date I have come close to winning the IFFB Pro Card but just missed it on two occasions. I am hoping to get the IFBB Pro Card this times around but I know the competition will be very competitive.

Categories: 4.5mm / .177 cal, 6mm, Airsoft, BB, Blowback, CO2, Full Auto, Replica Airguns News, Semi Auto, Pistol, Rifle, YouTube Video Tags: Crosman, Bushmaster MPW, KWC, Taurus PT24 24/7, Umarex, Makarov PM, Makarov

Tokyo Marui FNX-45 Tactical GBB Airsoft Pistol TableTop Review

1 Comment

Type: GBB Airsoft Pistol.
Manufacturer: Made by Tokyo Marui.
Model: FNX-45 Tactical.
Materials: Mostly polymer with metal components.
Weight: 1.8 pounds (830 grams).
Barrel: 4.4 inches metal non-rifled.
Propulsion: Green gas.
Action: Semi auto blowback, singled double action trigger.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 29 round drop out full size metal magazine.
FPS: Claimed 366.

Trigger Pull: The single action trigger pull on the Tokyo Marui FNX-45 Tactical GBB Airsoft Pistol is light and smooth with just a bit of take-up and a crisp release. You can also shoot in double action, as expected the trigger pull in double action will be longer and heavier but it’s still pretty smooth and not at all heavy.

Accuracy: At this point I have not shot the Tokyo Marui FNX-45 Tactical GBB Airsoft Pistol so I have no idea what the actual fps is and how accurate it may be but I can say I like the feel of how it dry fires so if that’s any indication as to how well it performs then I have high hopes for the Tokyo Marui FNX-45 Tactical GBB Airsoft Pistol.

Build Quality: The Tokyo Marui FNX-45 Tactical GBB Airsoft Pistol even though on the outside it’s all plastic (Slide and frame), the quality is fantastic, fit and finish is top notch everywhere and you will find metal parts where they need to be as in the inner and outer barrel, trigger, hammer, slide catch release, back strap safety, trigger group and many more internal parts.

Realism: The Tokyo Marui FNX-45 Tactical GBB Airsoft Pistol is virtually an exact replica of a Real Steel FNX-45 Tactical, looking at photos online of the powder burning version it is nearly impossible to tell them apart. You will find FN licensing in all the right places but keep in mind Tokyo Marui does not actually hold an FN license so yours will come with black stickers over the FN markings. Easy enough to take off :) In terms of functionality the Tokyo Marui FNX-45 Tactical GBB Airsoft Pistol operated pretty much exactly like the real steel version including the ability to field strip it for easy Hop-up adjustments.

Pros:

  • Ultra realistic Replica of the FNX-45 with authentic markings.

  • Removable slide cover allows mounting of red dot sight.

  • 16mm CW threaded barrel is mock suppressor-ready.

  • Multiple grip backstraps for a custom fit to your hand size.

  • Overall quality, fit and finish is excellent.

  • Easy to see white dot sights front and back.

  • Full size full metal magazine.

  • Ambidextrous safety, slide catch and magazine release.

  • Can easily put a mock suppressor on it.

  • Comes with additional internal barrel lengths for a mock suppressor or no meat tenderizer setup.

  • All mechanical parts work just like a steel FNX-45.

  • Super fast blowback action, great for action shooting.

Cons:

  • Mostly all plastic build.

  • Not actually licensed by Tokyo Marui.

Comments:

I am really liking the Tokyo Marui product line and welcome it to our Canada Replica Airguns Store. The Tokyo Marui FNX-45 Tactical GBB Airsoft Pistol is one the nicest quality Airsoft guns I have reviewed so far, it really is a work of art. The only thing that would be nice is a metal slide but I can live without it since everything else about the gun is nearly perfect! The Tokyo Marui FNX-45 Tactical GBB Airsoft Pistol is really built for everyone, left hand or right handed, large or small hands, the full set of ambidextrous controls and interchangeable back-straps will take care of you.

Categories: 6mm, Airsoft, Blowback, Gas, GBB, Pistol, Review, Semi Auto, YouTube Video Tags: Tokyo Marui, FNX-45 Tactical

Tokyo Marui Strike Warrior .45 1911 GBB Airsoft Pistol Table Top Review

No Comments

Type: GBB Airsoft Pistol.
Manufacturer: Made by Tokyo Marui.
Model: Marui Strike Warrior .45 1911.
Materials: Mostly polymer with metal components.
Weight: 1.8 pounds (816 grams).
Barrel: 3.9 inches metal non-rifled.
Propulsion: Green gas.
Action: Semi auto blowback, single action only trigger.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 28 round drop out full size metal magazine.
FPS: Claimed 366.

Trigger Pull: The single action only trigger pull on the Tokyo Marui Strike Warrior .45 1911 GBB Airsoft Pistol is extremely nice, there is virtually zero take-up with a light and easy release. You can really hammer out quick shots with this Airsoft pistol. One of the best 1911 triggers I have tested so far.

Accuracy: At this point I have not shot the Tokyo Marui Strike Warrior .45 1911 GBB Airsoft Pistol so I have no idea what the actual fps is and how accurate it may be but I can say I like the feel of how it dry fires so if that’s any indication as to how well it performs then I have high hopes for the Tokyo Marui Strike Warrior .45 1911 GBB Airsoft Pistol.

Build Quality: The Tokyo Marui Strike Warrior .45 1911 GBB Airsoft Pistol even though on the outside it’s all plastic (Slide and frame), the quality is fantastic, fit and finish is top notch everywhere and you will find metal parts where they need to be as in the inner and outer barrel, trigger, hammer, slide catch release, back strap safety, trigger group and many more internal parts.

Realism: The Tokyo Marui Strike Warrior .45 1911 GBB Airsoft Pistol is built on the Colt 45 1911 design but as you can see it comes in a compact version with a very tactical and aggressive look. You can tone it down a bit by removing the “Meat Tenderize” from the front basically turning it into a straight forward Tactical 1911 Compact version.

Pros:

  • Custom Detonics style slide and outer barrel.

  • Meat tenderizer-like Strike Face muzzle gives gun aggressive appearance.

  • 20mm underside rail for laser or flashlight attachment.

  • Squared-off SAO trigger guard with short-stroke trigger pull.

  • Fit and finish is excellent.

  • Easy to see white dot sights front and back.

  • Full size full metal magazine.

  • Very cool looking tactical compact 1911.

  • Ambidextrous safety.

  • Comes with additional internal barrel lengths for a Mock suppressor or no Meat tenderizer setup.

  • Working grip safety as you would expect.

  • All mechanical parts work just like a real steel 1911.

  • Super fast blowback action, great for action shooting.

Cons:

  • Mostly all plastic build.

  • Can not field strip easily and get to the hop-up adjustment with the Meat tenderizer on it.

Comments:

This is my first real experience with a Tokyo Marui product and I have to say I am very impressed with their build quality and design. Even though the slide and frame are plastic, there is enough metal going on in this Airsoft pistol to give it decent enough weight and feel. I really like what Tokyo Marui did with the styling of the Tokyo Marui Strike Warrior .45 1911 GBB Airsoft Pistol with the Meat tenderizer-like Strike Face muzzle, squared-off trigger guard and overall tactical look and feel. A great addition to the Replica Airguns Canada Online Store!

Categories: 6mm, Airsoft, Blowback, Gas, GBB, Pistol, Review, Semi Auto, YouTube Video Tags: Tokyo Marui, Strike Warrior .45

Tokyo Marui New Product Preview Unboxing Video

No Comments

TokyoMaruiLogo.jpg

I though I would feature the fact that we recently added some of the Tokyo Marui product line to our Canada Replica Airguns Store. Tokyo Marui is said to be one of the best Airsoft products on the market and they have been around for a while so they have had time to get it right! As Tokyo Marui is a Japanese based company they are restricted to only being able to use plastic frames and slides but even with this limitation the Tokyo Marui products that I have personally looked at are extremely well made.

In this Tokyo Marui New Product Preview Unboxing Video I take a look at 4 Tokyo Marui models; the Tokyo Marui Strike Warrior .45 1911 Gas Blowback Airsoft Pistol, the Tokyo Marui Hi-Capa 5.1 D.O.R (Direct Optics Ready) GBB Airsoft Pistol, the Tokyo Marui FNX-45 Tactical Gas Blowback Airsoft Pistol and lastly the Tokyo Marui VSR-10 Pro Sniper Bolt Action Airsoft Rifle.

Tokyo Marui Strike Warrior .45 1911 Gas Blowback Airsoft Pistol

  • Type: Airsoft Pistol

  • Manufacturer: Tokyo Marui

  • Model: Strike Warrior .45

  • Materials: ABS

  • Weight: 816 g (1.8 lb)

  • Length: 205 mm (8.1 in)

  • Barrel: 74 mm (2.9 in), metal

  • Power Source: Green Gas

  • Action: Semi-automatic, blowback

  • Ammo Type: 6mm airsoft BBs

  • Ammo Capacity: 28 rounds

  • FPS: 366

Tokyo Marui Hi-Capa 5.1 D.O.R (Direct Optics Ready) GBB Airsoft Pistol

  • Type: Airsoft Pistol

  • Manufacturer: Tokyo Marui

  • Model: Hi-Capa 5.1 D.O.R.

  • Materials: Polymer and metal

  • Weight: 839 g (1.85 lb)

  • Length: 220 mm (8.7 in)

  • Barrel: 112 mm (4.4 in), metal

  • Power Source: Green Gas

  • Action: Semi-automatic, blowback

  • Ammo Type: 6mm airsoft BBs

  • Ammo Capacity: 31 rounds

  • FPS: 366

Tokyo Marui FNX-45 Tactical Gas Blowback Airsoft Pistol

  • Type: Airsoft Pistol

  • Manufacturer: Tokyo Marui

  • Model: FNX-45 Tactical

  • Materials: ABS

  • Weight: 830 g (1.8 lb)

  • Length: 220 mm (8.7 in)

  • Barrel: 113 mm (4.4 in)

  • Power Source: Green Gas

  • Action: Semi-automatic, blowback, single/double-action

  • Ammo Type: 6mm airsoft BBs

  • Ammo Capacity: 29 rounds

  • FPS: 366

Tokyo Marui VSR-10 Pro Sniper Bolt Action Airsoft Rifle

  • Type: Airsoft Rifle

  • Manufacturer: Tokyo Marui

  • Model: VSR-10 Pro Sniper vers.

  • Materials: ABS

  • Weight: 1.9 kg (4.2 lb)

  • Length: 107.5 cm (42.3 in)

  • Barrel: 430 mm (17 in)

  • Power Source: Spring

  • Action: Bolt action

  • Ammo Type: 6mm airsoft BBs

  • Ammo Capacity: 30 rounds

  • FPS: 366

Categories: 6mm, Airsoft, Blowback, Comparison, GBB, Gas, Pistol, Review, Replica Airguns News, Rifle, Semi Auto, Spring Piston, YouTube Video Tags: Tokyo Marui, VSR-10 Pro, FNX-45 Tactical, Hi-Capa 5.1 D.O.R., Strike Warrior .45

Umarex T4E HK 416 Training Marker CO2 Paintball Rifle Field Test Review

No Comments

If you have not already watched my Table Top Video Review for the Umarex T4E HK 416 Training Marker CO2 Paintball Rifle than make sure to do so if you are interested in more specifications and details.

I don’t often make many Paintball Review Gun Videos let alone Shooting Videos so this one is a bit different than the norm. Lucky for me I have some .43 caliber Rubber Paintballs that I can use in my Indoor Sea Can Shooting Range so as not to make a mess of things. As per usual I like to use a brand new 12 Gram CO2 Cartridge for my testing and for your reference the temperature was right around room temperature or 21 degree Celsius, 69 degrees Fahrenheit.

First up I generally perform my Chronograph test to see what the real world velocity or fps is for the Umarex T4E HK 416 Training Marker CO2 Paintball Rifle. I shot a short string of rubber rounds through my Chronograph and was able to get a 280 fps average with the Umarex T4E HK 416 Training Marker CO2 Paintball Rifle. This is plenty enough power for the intended target down range to feel the paintball effect without causing too much trauma.

With the remaining 10 rounds in my Umarex T4E HK 416 Training Marker CO2 Paintball Rifle magazine, I then setup a brand new paper target 30 feet down range and using a rested and seated shooting position and carefully unloaded the Umarex T4E HK 416 Training Marker CO2 Paintball Rifle into the target. I was a bit surprised to see the rounds spread out a fair amount perhaps as much as 10-12 inches but at least half where in the target rings.

I would not recommend the Umarex T4E HK 416 Training Marker CO2 Paintball Rifle as a long range paintball marker but it would be perfect for close quarters ultra realistic simulations. I would like to give actual .43 caliber paintballs a try outside to see if accuracy would be better, maybe the rubber balls grip the barrel a bit too much causing some random and unexpected spinning to occur? Either way the Umarex T4E HK 416 Training Marker CO2 Paintball Rifle is a really unique and fun Paintball Gun to shoot, maybe not for everyone but if you want the most realistic Paintball Marker then it would be a great option.

Categories: .43 cal, Blowback, CO2, Field Test, Paintball, Review, Rifle, Semi Auto, YouTube Video Tags: Umarex, T4E HK416

Umarex T4E T4E HK 416 Training Marker CO2 Paintball Rifle Table Top Review

No Comments

Type: Paintball Rifle.
Manufacturer: Umarex - T4E.
Model: H&K 416.
Materials: Metal & Polymer.
Weight: 3016 grams (6.65 pounds).
Barrel: Metal smooth bore.
Power Source: 1x12 gram CO2.
Action: Semi-Automatic with internal working bolt blowback action.
Ammo Type: .43 Caliber Paintball or Rubber Ball.
Ammo Capacity: 14 Rounds.
FPS: 330-460?

Trigger Pull: The trigger pull on Umarex T4E T4E HK 416 Training Marker CO2 Paintball Rifle is pretty typical of what you would find on an AR styled rifle. Since the internal bolt cycles with each shot, the trigger is engaged and the Paintball rifle is ready for the next shot with a very light and short single action trigger pull.

Accuracy: So far I have not had the opportunity to test the Umarex T4E T4E HK 416 Training Marker CO2 Paintball Rifle other than placing a few rounds down range into my ammo trap to see how it shot and felt. Without actually shooting rounds through the Chronograph I don’t really know what the fps velocity is going to be but I can say it felt like it was shooting perhaps even over 400 fps? Out of the box the Umarex T4E T4E HK 416 Training Marker CO2 Paintball Rifle was shooting rather low but you can adjust the rear sight for windage and elevation.

Build Quality: The build quality of the Umarex T4E T4E HK 416 Training Marker CO2 Paintball Rifle is very good since this Paintball gun is made for military and law enforcement training use. You’re going to find high quality metal and polymer where you would normally find them on the real steel version. The bolt carrier is expected to last at least 3000 shots but you do get an extra one included with it.

Realism: The fully licensed Umarex T4E T4E HK 416 Training Marker CO2 Paintball Rifle is about as realistic as you are going to get in a Paintball Rifle. It’s basically made very similar to a GBB Airsoft Rifle of the same type with a working bolt and pretty much all working parts on it. You can even break the Umarex T4E T4E HK 416 Training Marker CO2 Paintball Rifle down into the lower and upper receiver halves. The bolt blowback action is not super strong but this may be a good thing since CO2 usage will be more efficient allowing for higher fps and more shots per CO2.

Purchase it from the Canada Replica Airguns Store or the US Replica Airguns Store

Pros:

  • Seem to have decent fps, will see when I do my Field Test?

  • Full Size drop out magazine that holds 14 .43 caliber Paintballs and the CO2.

  • Removable 4 position adjustable stock.

  • Removable and adjustable iron sights.

  • Lots of rials for adding accessories.

  • Fully licensed H&K 4116 replica via Umarex.

  • Blowback does give a bit of recoil feedback and allow for a true single action trigger.

  • Very high quality metaled polymer build.

  • Used as a training weapon for military and law enforcement.

  • Comes with extra bolt carrier.

Cons:

  • Very expensive, well over $1000!!

  • Comes with blue hardware but can be swapped out (Pistol grip, But stock, Magazine).

  • Bolt carrier may wear out at around 3000 rounds.

Comments:

If’ you’re looking for the ultimate in Paintball Rifle realism the Umarex T4E T4E HK 416 Training Marker CO2 Paintball Rifle is going to meet that requirement for sure. It will come at a pretty decent cost but you are going to have a very unique Airgun that not many people will own. And as they say you do get what you pay for which is realism, quality and reliability. I look forward to testing out the Umarex T4E T4E HK 416 Training Marker CO2 Paintball Rifle on the Chronograph using some rubber ball ammo, I may even take it outside for some paintball ammo shooting, we will have to see…

Categories: .43 cal, Blowback, CO2, Paintball, Review, Rifle, Semi Auto, YouTube Video Tags: T4E HK416, Umarex

G&G GPM1911 GBB Airsoft Pistol Field Test Review

No Comments

I’m going to start off by saying this Field Test Shooting Review for the G&G GPM1911 GBB Airsoft Pistol did not go all that well as I had some complications with this Airgun when chambering rounds. I am pretty sure it is magazine related and hope to try a different magazine with it soon. I say this because I am following through with my review regardless of my initial results to demonstrate that not all Airguns perform as expected during my reviews and sometimes you get a lemon even with a good quality brand like G&G.

I am fairly certain the defect in this case for the G&G GPM1911 GBB Airsoft Pistol was the magazine tip being too tight and not allowing an Airsoft BB to position all the way to the top of the magazine which means when the slide cycled and the nozzle was in position to push an Airsoft BB into the breach, it simple was hitting the top of the BB and pushing it even further into the magazine. All said and done I was able to test the fps and accuracy on target so let’s get on with my review.

Using .20 gram Airsoft BB’s with a fully filled propane gas magazine in my G&G GPM1911 GBB Airsoft Pistol, I was able to get 6 recoreded shots through my Chronograph averaging 319 fps. The slowest shot being 313 fps and the fastest shot hitting 330 fps. The temperature was right around room temperature so around 22 degrees Celsius or 72 degrees Fahrenheit.

As I was having issues with with the G&G GPM1911 GBB Airsoft Pistol chambering rounds with the .20 gram Airsoft BB’s. I was hoping that when I switched to a different .32 gram Airsoft BB for my target portion of this review that perhaps the different Airsoft BB’s would chamber better but they did not. To get through the target portion of my test, with each shot I had to drop the magazine, make sure the Airsoft BB’s was at the top of the magazine, rack the slide, insert the magazine and then release the slide. So as you can see I was resetting completely for each shot which does not always make for the tightest groupings. Surprisingly I was still able to get about a 1.5 inch grouping on my paper target setup 30 feet downrange using a rested and seated shooting position.

Not all reviews go as planned but you still have to make the best of it. I really feel the G&G GPM1911 GBB Airsoft Pistol is a good gun overall even though mine did not perform that well for me. When I was able to chamber a round it shot a consistent fps and placed Airsoft BB’s downrange accurately and very close to the bullseye. Perhaps simply by swapping out the magazine I will have a much more reliable Airsoft gun? I will have to get back to you on that one.

Categories: 6mm, Airsoft, Blowback, Field Test, Gas, GBB, Pistol, Review, Semi Auto, YouTube Video Tags: G&G, GPM1911, 1911, M1911 A1

G&G GPM1911 GBB Airsoft Pistol Table Top Review

2 Comments

Type: Gas Blowback Airsoft Pistol.
Manufacturer: G&G
Model: GPM1911
Materials: Metal slide, frame & Magazine.
Weight: 2.25 pounds (1020 grams).
Length: 8.66 inches (22.0 cm) total.
Barrel: 4.58 inches (11.7 cm), Metal non-rifled smooth bore.
Propulsion: Green gas or propane.
Action: Blowback, single action only.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 25 rounds.
FPS: 300-330 fps.

Trigger Pull: The single action only trigger pull on the G&G GPM1911 GBB Airsoft Pistol is what you would expect from a traditional single action only 1911 trigger, a very short take-up and a crips and light release. Great for getting a lot fo shoots off quickly and accurately down range without making your trigger finger do a lot of work.

Accuracy: I have not done my actual Field Test Shooting video review for the G&G GPM1911 GBB Airsoft Pistol so I can into comment just yet but I will be making a Field Test Shooting Video for it as soon as I can and will post that here on the website and of course over on the Replica Airguns YouTube channel when I have it ready.

Build Quality: The G&G GPM1911 GBB Airsoft Pistol is in my opinion one for the nicer looking finishes wise and I would have to say it seems to also be one of the better quality 1911 Airguns out there, for sure a step up from a KWC blowback 1911’s and in line with what KWA and KJWorks is making these days which is good quality. The G&G GPM1911 GBB Airsoft Pistol is one of the heavier Airsoft 1911 Blowback Pistols which makes me think the metal is a bit higher quality where it needs to be. Tolerances are nice and tight and the blowbacks action is very heavy.

Realism: The G&G GPM1911 GBB Airsoft Pistol like most of these full blowback 1911 Airguns, Steel BB or Airsoft BB, is super realistic with an all metal build. All the real steel working parts like the slide catch release, back strap safety and pretty much everything else function as they should. The G&G GPM1911 GBB Airsoft Pistol even field strips like a traditional 1911 pistol. Not sure what you could do to make it more authentic for an Airgun?

Available in the: Replica Airguns Store

Pros:

  • Nice high capacity magazine compared to other GBB 1911 Airsoft pistols.

  • Heavier than most Airsoft 1911’s.

  • All parts fit nice and tight, tolerances are very good.

  • Working back-strap safety.

  • No ugly red tip.

  • Finish is really nice, gun looks really good.

  • Expect to get decent amount of shots per gas fill.

  • Micro Gas Filter and Whirl Cylinder Valve help to manage gas efficiency and reduced frost buildup.

  • Traditional adjustable Hop-up.

  • Full Size Dropout metal magazine pretty standard on Airsoft pistols.

  • Comes with high quality hard shell case and speed loader.

Cons:

  • Sights are pretty basic, no white dots and non-adjustable as you would expect on a 1911 A1.

  • Very simple Airsoft gun, no modern bits and pieces on it.

  • FPS could be a bit higher but fine for close quarters.

Comments:

The G&G GPM1911 GBB Airsoft Pistol is for sure one of the nicer 1911 A1 styled Airsoft pistols, inline with KWC and KJWorks. It does come in a little bit heavier and seems to have more blowback recoil action which is nice. All I need to do now is find out how well it shoots! If it’s not half bad then it is for sure worth the price which by the way is a little bit cheaper than a KWA or KJWorks 1911 and about the same price as a KWC 1911. So many choices I know but that’s a good thing :)

My Table Top Review of the G&G GPM1911 GBB Airsoft Pistol:

Categories: 6mm, Airsoft, Blowback, Comparison, Gas, GBB, Pistol, Review, Semi Auto, YouTube Video Tags: G&G, GPM1911

Webley Nemesis and G&G GPM1911 Unboxing Preview Video

No Comments

I keep getting more and more really cool airguns to review and it’s been hard to keep up with them all and get out Table Top and Field Test videos for each new product. I at least want to be able to get the word out so to speak for some of the new Airguns that come across my tassel even if I may not be able to get to their full reviews right away.

That said I have two new Airguns that we have in our Replica Airguns Stores to show everyone, the Webley Nemesis in .177 Caliber Pellet and the G&G GPM1911 GBB Airsoft Pistol. Both could not be any more different for sure but I really like each of them for their own reasons.

The Webley Nemesis is a very unique CO2 powered pistols since it is bolt action like many of the corpsman pistols but the Webley Nemesis .177 Caliber Pellet Pistol comes with a duel sided rotary magazine that holds 7 rounds on each side, the .22 caliber version holds 6 rounds on each side. The .177 caliber version can shoot up to 450 fps while the .22 caliber version has a claimed fps of up to 370. I look forward to testing and reviewing the Webley Nemesis .177 Caliber Pellet Pistol as soon as I can.

I also showcase the G&G GPM1911 GBB Airsoft Pistol which is a well priced basic A1 styled 1911 that is really well built and about one of the heaviest full metal 1911’s I have come across to date hitting the scale at nearly 2 pounds and 4 ounces. Another Replica Airgun I look forward to treating out!

Categories: .22 cal, 4.5mm / .177 cal, 6mm, Airsoft, Blowback, CO2, GBB, Gas, Pellet, Pistol, Review, Semi Auto, YouTube Video Tags: Webley, Nemesis, G&G, GPM1911

Air Venturi Springfield Armory M1 Carbine CO2 BB Rifle Field Test Review

1 Comment

Lots of CO2 BB Rifles getting reviewed these days and that’s kind of awesome, I remember a few years back and we barely had any realistic Replica BB rifles available to us. Now we have an ever increasing list of choices from Historical to Modern.

Todays Field Test Shooting Video focusses on the Air Venturi Springfield Armory M1 Carbine CO2 BB Rifle, I have not done my Table Top Video yet for it but I did make a preview video where I show it around a bit and talk about some basic specs. In short the Air Venturi Springfield Armory M1 Carbine CO2 BB Rifle is a CO2 powered semi auto 4.5mm Steel BB firing replica of the Springfield Armory M1 Carbine. It holds the CO2 and 15 rounds of Steel BB’s in its full size drop out metal magazine. Available with a plastic or upgraded wood stock.

For the Field Test Shooting part of this review I tested out the power and accuracy of the Air Venturi Springfield Armory M1 Carbine CO2 BB Rifle by first shooting 5 rounds through my Chronograph to establish the Feet Per Second velocity. I then placed a fresh paper target 30 feet downrange, while using a rested and seated shooting position I fired off 10 rounds into the target to see how tight of a group I can get with the Air Venturi Springfield Armory M1 Carbine CO2 BB Rifle. I used a brand new CO2 along with 5.1 grain 4.5mm Zinc coated Steel BB’s. The temperature was a conservative 22 degrees Celsius or 71 degrees Fahrenheit.

During my Chronograph velocity test I was a bit surprised to only obtain an average of 335 fps from the Air Venturi Springfield Armory M1 Carbine CO2 BB Rifle. Air Venturi claims closer to 425 so I am not sure why it was nearly 100 fps lower than claimed but perhaps the CO2 did not pierce as well as it could have, that said 335 fps does get the job done when shooting targets 20-30 feet away.

In terms of accuracy I was very pleased with the Air Venturi Springfield Armory M1 Carbine CO2 BB Rifle, it kind of made up for the slower than expected feet per second by getting a sub 1 inch 10 round group and I am not a big fan of peep sights so I was really not expecting these results. Right out of the box the Air Venturi Springfield Armory M1 Carbine CO2 BB Rifle shot pretty close to the bullseye, just s slight bit to the left and about 1-2 inches high. The rear sight is adjustable for elevation so that can be taken care of pretty easy.

All in all I really like the Air Venturi Springfield Armory M1 Carbine CO2 BB Rifle other than the lower than expected fps which may have been something to do with my rifle? I will have to try a fresh CO2 with it sometime to see if this can be improved but even with the lower velocity the Air Venturi Springfield Armory M1 Carbine CO2 BB Rifle performs well hitting what ever you are shooting at with excellent accuracy. The blowback action gives the Air Venturi Springfield Armory M1 Carbine CO2 BB Rifle just enough recoil feel to tap your shoulder a bit and of course give you that nice short and light single action only trigger.

Categories: 4.5mm / .177 cal, BB, Blowback, CO2, Field Test, Review, Semi Auto, YouTube Video, Rifle Tags: AirVenturi, Springfield Armory, M1 Carbine

Crosman Bushmaster MPW CO2 Blowback BB Machine Gun Field Test Review

No Comments

Make sure to watch my Table Top Video Review for the Crosman Bushmaster MPW CO2 Blowback BB Machine Gun for all the details and specifications. And if you have not already taken a look at the Crosman DPMS SBR CO2 Blowback BB M4 then watch those video reviews since both guns are very similar internally with some cosmetic differences.

The purpose of my Field Test Shooting Video is to find out how the airgun being reviewed performs in terms of velocity and accuracy, and if the ratings on paper end-up being the same or close to the tested results. Crosman claims the Crosman Bushmaster MPW CO2 Blowback BB Machine Gun is capable of shooting 5.1 grain 4.5mm Steel BB’s at up to 430 fps. When I tested the Crosman Bushmaster MPW CO2 Blowback BB Machine Gun using my Chronograph averaging out 5 shots using a brand new set of CO2 cartridges I averaged 385 fps. Note the temperature in my Indoor Airgun Sea Can Shooting Range was not super warm at about 20-22 degrees Celsius or right around 70 degrees Fahrenheit. I was able to get 405 fps from the Crosman DPMS SBR CO2 Blowback BB M4 but I have a feeling the temperate may have been a little bit warmer for the DPMS SBR Testing which does help to increase the fps.

Moving on to the accuracy portion of this Field Test Shooting Review for the Crosman Bushmaster MPW CO2 Blowback BB Machine Gun, I loaded up the 25 round magazine with the maximum amount t it would hold and then placed 10 semi auto shots on my paper target setup 30 feet downrange. I was using a rested and seated shooting position to help minimize human factor. I was a bit surprised that the Crosman Bushmaster MPW CO2 Blowback BB Machine Gun shot a 2.5 inch semi auto 10 shot group since the Crosman DPMS SBR CO2 Blowback BB M4 was able to get just under 1 inch when I performed the same test.

I then flipped the semi auto selector switch to full auto and dumped the remaining 15 rounds into my paper target in full auto mode and to my surprise the Crosman Bushmaster MPW CO2 Blowback BB Machine Gun actually tightened up it’s grouping a little bit closer to 1.5 inches which is amazing in full auto mode with the airgun rocking around a lot due to the blowback action.

In summary the Crosman Bushmaster MPW CO2 Blowback BB Machine Gun performed a lot like the Crosman DPMS SBR CO2 Blowback BB M4, just a little bit lower fps perhaps because of the difference in temperature when both of the airguns where tested. In semi auto mode I should have been able to get a tighter grouping, perhaps it was my performance on this day? But in full auto mode I was able to get nearly identical results as I shot with the Crosman DPMS SBR CO2 Blowback BB M4.

I think it really comes down to which of the Crosman AR type full auto BB rifles you like the look of since both are very capable shooters. Or just get both if you can’t decide :)

Categories: 4.5mm / .177 cal, BB, Blowback, CO2, Field Test, Full Auto, Review, Rifle, Semi Auto, YouTube Video Tags: Crosman, Crosman MPW, Bushmaster MPW, Crosman Remington DPMS SBR

Umarex Legends Cowboy Shell Ejecting CO2 BB Rifle Review

1 Comment

This Review for the Umarex Legends Cowboy Shell Ejecting CO2 BB Rifle is a bit different than most I do since usually I perform a dedicated Table Top and Field Test Reviews for each gun I review here on the Replica Airguns Website. I feel that since the Umarex Legends Cowboy Shell Ejecting CO2 BB Rifle is such a “long gun” that showing it on the table would not work so well , plus it was a super nice day and I wanted to get outside and maybe even shoot a little bit.

I will be performing my usual Field Test Shooting video where I test the Feet Per Second and accuracy at 30 feet so stay posted for that. For now I will leave you with this outdoor “Show and Tell” review.

Specifications:

Type: CO2 BB Rifle.
Manufacturer: Umarex
Model: Umarex Legends Cowboy
Materials: Mainly metal with plastic stock.
Weight: 5.95 pounds (2699 grams).
Length: 38 inches total length
Barrel: 19.25 inch Metal non-rifled smooth bore.
Propulsion: Dual 12 gram CO2.
Action: Lever Action.
Ammunition Type: 4.5mm Steel BB's.
Ammunition Capacity: 10.
FPS: 410 fps.

Trigger Pull: The trigger pull on the Umarex Legends Cowboy Shell Ejecting CO2 BB Rifle is pretty much a single action only trigger since you will need to work the lever action to not only elect and chamber a shell but to also pre cock the hammer. Once the hammer is cocked and ready the trigger pull is short, light and crips, perfect for accurate shooting.

Accuracy: I have only shot 16 rounds through the Umarex Legends Cowboy Shell Ejecting CO2 BB Rifle during the making of this review video and found the Umarex Legends Cowboy Shell Ejecting CO2 BB Rifle to shoot right on target at 30 feet out. I did notice it shot just slightly high at this range but not a lot and it was dead center windage wise. For longer ranges you can adjust the rear sight to raise the barrel even more. In terms of power it’s hard to say what I was getting, Umarex says it should hit around 410 fps, I felt like it was pretty close to this , maybe a tad bit faster but I will find out for sure when I perform my Field Test Shooting Video Review shortly.

Build Quality: The Umarex Legends Cowboy Shell Ejecting CO2 BB Rifle looks and feels great coming in at nearly 6 pounds and built out of mostly metal with a plastic stock. Don’t be too put out by the plastic stock, it does mimmic the part of wood very well. All the metal parts have a semi-gloss or I would even say matt back finish and so far the paint is wearing pretty good, no noticeable paint coming off that I can see. The action works great with no failure to chamber, eject or shoot rounds.

Realism: The Umarex Legends Cowboy Shell Ejecting CO2 BB Rifle is an awesome example of the classic lever action cowboy rifle. Having the ejecting shells makes it feel like you are shooting the real deal right from the time you start loading up the 10 shells into the pipe magazine, until you work that lever action and pull the trigger. Watching the ejected shells fly through the air is the icing on the cake :) There is not much more you can ask for from a BB firing replica Lever Action Cowboy Rifle!

Pros:

  • Super realistic replica lever action BB firing Cowboy Rifle.

  • Fully working lever action, chambers and ejects shells perfectly.

  • Good weight and feel to it with lots of metal throughout.

  • Everything works exactly like the real steel version.

  • Duel CO2 to help get not only more shots before reloading CO2 but also a more consistent FPS from all shots.

  • Adjustable rear sight for elevation.

  • Comes with 10 rounds and can also use your Umarex Colt Single Action Army BB shells in it.

  • Plastic imitation wood stock looks very much like real wood.

Cons:

  • Stock is not real wood, hopefully Umarex offers a wood upgrade for it at some time.

  • A bit low in FPS, why not take it right up to 499 fps since the US version has a 600 fps rating.

  • Took too long for us to get it here in Canada!.

Comments:

The Umarex Legends Cowboy Shell Ejecting CO2 BB Rifle is a perfect example of an Airgun company listening to their customers and bringing to market exactly what we are looking for, kind of like the Single Action Army Revolvers that came out a while back. These old cowboy guns are a blast to shoot from the time you pick up the rifle, insert 10 shells into the magazine, work the lever action, pull that trigger and then repeat 10 times. This is a must have for anyone looking for a super realistic BB rifle, even if you’re not an old west cowboy fan I think you will love shooting the Umarex Legends Cowboy Shell Ejecting CO2 BB Rifle!

My Table Top Video of the Umarex Legends Cowboy Shell Ejecting CO2 BB Rifle:

Categories: 4.5mm / .177 cal, BB, CO2, Field Test, Review, Repeater, Rifle, YouTube Video Tags: Umarex, Legends Cowboy Rifle

Air Venturi Springfield Armory XDM BB vs Airsoft Pistol Comparison

1 Comment

For more of a traditional Table Top Features and Specifications video for the Air Venturi Springfield Armory XDM Air Pistol, then watch my Table Top Review for the Airsoft Springfield Armory XDM here.

Since both the 6mm Airsoft and 4.5mm Steel BB Air Venturi Springfield Armory XDM’s are nearly identical with only a few exceptions, I didn’t feel it was necessary to make another almost identical Table Top Video for the Steel BB firing Air Venturi Springfield Armory XDM. Instead I want to focus mainly on the differences in this comparison video.

Watch my Video for all the main differences but in short here they are for those reading this post:

  • Steel BB version uses CO2 while the Airsoft version uses Green Gas or Propane.

  • There is no orange tip on the Steel BB version while Airsoft versions come with orange tips installed.

  • Steel BB versions have 20 round full length magazines for both the 3.8 and 4.5 inch versions, while the Airsoft 3.8 compact comes with the shorter 14 round magazine and the Airsoft 4.5 comes with a longer 25 round magazine.

  • FPS for the Steel BB versions are 270fps for the 3.8 and 325fps for the 4.5, comparably the Airsoft 3.8 is claimed to have 280fps with the 4.5 version a bit higher at 330fps. (Keep in mind that steel BB’s weigh more at around .33 grams compared to the .20 gram plastic Airsoft BB’s used for testing).

  • I did notice that on the sliver slide version, my earlier Airsoft 4.5 had more of a parkerized metallic finish while my same Steel BB version I received at a later time had more of brushed stainless look to it. Air Venturi has since informed me that all silver slide version will now have the brushed stainless finish.

Categories: 6mm, 4.5mm / .177 cal, Airsoft, Blowback, CO2, Comparison, Gas, GBB, Pistol, Review, Semi Auto, YouTube Video Tags: AirVenturi, Springfield Armory, XDM