In this Field Test Shooting Video I put the Webley Valuemax 22 Caliber Spring Piston Break Barrel Rifle through my standard Replica Airguns Indoor Field Test protocol by first testing out the velocity and placing 5 rounds through my Chronograph to see what the actual real world fps is using 14.3 grain lead pellets. I then setup a fresh paper target 30 feet downrange and place 10 pellets into it to see what type of grouping I can get. If you have not already watched my Table Top Video for this Break Barrel Spring Piston Pellet Rifle then make sure to do so for more details, specifications and close up video.
Starting off with my real world velocity test for the Webley Valuemax 22 Caliber Spring Piston Break Barrel Rifle, I went with 14.3 grain lead pellets which are I would say on the heavier side. Even so I managed to hit 478 fps which produced a nice 7.26 foot pounds of energy which by the way is almost 10 Joules! If you are wondering about Canadian legalities, as long as I do not go over 500 fps AND go over 4.2 foot pounds (both thresholds must be exceeded), then this Airgun is considered a non-regulated firearm and does not require a firearms license.
Moving on to the accuracy portion of my Indoor Field Test in the Replica Airguns Sea Can. As always I placed a brand new paper target 30 feet downrange and proceeded to shoot ten 14.3 grain lead pellets from a rested and seated shooting position to allow for best possible results with as little human error but I am imperfect so some human error is always present. I was using the open fiver optic sights on the Webley Valuemax 22 Caliber Spring Piston Break Barrel Rifle rather than a scope even thought there is a dovetail rail with included scope stop. To be honest I was expecting a better grouping, something close to half an inch but on this day with this ammo choice I was closer to 1.5 to even 2 inches. I did see several pellets land in a tighter sub group but some came out of this group enlarging the grouping. I would like to try a different pellet choice to see if I can do better as I believe this rifle has way more potential.
In terms of power the Webley Valuemax 22 Caliber Spring Piston Break Barrel Pellet Rifle is about has high as you can go before it becomes a regulated firearm here in Canada so no complaints in that department. Again I was disappointed in the accuracy but I honestly believe a different pellet choice could fix that problem as I have seen often with other Pellet Rifles. Once the right pellet choice is made and granted a more consistent and tighter grouping is achieved, this Spring Piston Pellet Rifle could make a decent small pest control airgun!
Type: Pellet Rifle. Distributer:Webley & Scott. Model:Valuemax. Materials: Metal and polymer build. Weight: 6.4 pounds (2900 grams). Barrel: 17.7 inches (450mm), rifled. Total Length: 43 inches (1092mm) Propulsion: Spring Piston Action: Break Barrel. Ammunition Type: .22 Caliber Pellets. Ammunition Capacity: Single Shot. FPS: 499.
Trigger Pull: The trigger pull on the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle is fairly nice There is a little bit of very light take up followed by a vert light release , the take up or travel length can be adjusted on this Air Rifle but that is the only trigger adjustment you can make and perhaps all that is needed.
Accuracy: I have not performed my Field Test Shooting Video for the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle but I did get to take around 20 or so shots with it when I was trying to get it to diesel for me. It looks ot me like it is going to be nice and accurate as I was not even really going for accuracy and it seemed to already be grouping fairly tight. I was recoding fps using my Chronograph as I was trying to find out if by adding some oil to the spring piston chamber could get it to diesel which it never did for me, I was however to establish that the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle shot right around 470-480 fps using 14.3 grain lead pellets which worked out to right around 7.32 foot pounds of energy. I will know a lot more when I do my official Field Test Shooting Video next week.
Build Quality: Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle is built to be a value priced Airgun hence the name (Valuemax), that said it is maid well enough with lots of metal and of course some plastic or in this case mostly nylon as the stock is a solid nylon piece. Other than the stock the plastic parts are found to be in the sights and trigger guard, everything else seems to be metal.
Realism: The Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle is not a replica or copy of any real steel gun in production but it does look like a traditional hunting rifle in basic shape so make sure to transport thank airgun as if it was a real gun. Either in a gun case or perhaps a blanket in your trunk and always obey any laws for gun position and transportation in your area.
Pros:
Inexpensive price tag for well made decent performer.
Initial test showed to have good accuracy and power! (more to come).
Fully adjustable sights with optical TRUGLO Fiber Optics.
Can add a magnified optical scope using the top built in dovetail rail.
Nylon fiber stock is durable and functional with the addition of a vented rubber buttplate.
Trigger feels decent and is also adjustable for travel length.
Rear thumb safety resets after each break of the barrel.
Nice light and short single action trigger.
Would be good for small pest control because of decent FPS and good accuracy.
Cons:
Included sights are mostly plastic.
The Valuemax version has a more basic less adjustable trigger.
Detuned down to under 500 fps for Canada import as non-regulated Firearm.
Comments: I am looking forward to performing my Indoor Field Test Shooting Video for the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle to see what it can really do in terms of accuracy so stay posted for that video next week. Overall if you are lucky enough to already have one or can get your hands on one since this rifle is discontinued in some area, I think this is a great Break Piston Air Rifle especially if you live in Canada and want the most bang for your buck. I am not only talking about cost verses features, I also mean power and energy since the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle is a .22 caliber Air Rifle that can shoot really close to 500 fps with a nice heavy grain lead pellet achieving decent energy levels reasonable enough for small pest control. The Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle is not feature less, it does include a reseting safety, anti bear trap system, dove tail mounts with an included scope stop, fiver optic adjustable sights and a vert ergonomic textured nylon stock. All in all great value for what you pay!
My Vimeo Videos for the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle:
Wow, an accessory review, not many of these :) Today I take a look at the Amomax Airsoft Airgun Holster product line since at some point you may want to put your gun in a holster or practice drawing your gun from a holster?
The good news is we just got in a decent amount of product for our Amomax Airsoft Airgun Holsters. Here is a bit of info about Amomax but of course make sure to watch the video as I take a good look at a few of the versions we sell in our Canada and US online Replica Airguns Stores.
Amomax holsters are compatible with 4 different carrying platforms :paddle (standard), belt clip, MOLLE, and drop leg platforms. All the carrying platforms can be replaced by only one screw. Users can carry them in daily use, outdoor sports, normal shooting training and competition. Holster will stay firmly on a belt, leg and MOLLE system even in fast moving situations with a quick release Retention System button that keeps the gun locked in place until you are ready to draw. Holster body and carrying platform are connected with a tooth gear that allows for 360 degrees of rotation. User can easily adjust the carrying position to fit their needs.
Amomax Holsters are currently available in the following versions:
I will say right off the bat this Field Test Shooting Video for the Air Venturi 3000 PSI Aluminum HPA Tank with Stock and Adapter did not go as well as I would have wanted it to! The HPA tank itself worked really well but I believe the adapter was faulty as it was destroying the seals on my tank and not regulating very well.
I still wanted to publish this video regardless as not all reviews go as planned, some fail horribly but I would rather be honest and transparent about it rather than have you believe every product is a perfect.
There will always be problems even with really great products there can be defects. I plan to get a new adaptor and try this Field Test Review Video again but for now you can have some fun watching me at least have some success using the Air Venturi 3000 PSI Aluminum HPA Tank with Stock on my Rap4 Rap5 MP5.
You can also watch my Table Top Review Video for more details and info on this product!
I will also be following up my Table Top video with a Field Test Shooting Video to see what possible advantages and disadvantages the Air Venturi 3000 PSI with Stock & Adapter Aluminum Tank has in a real world test of its performance, hopefully all advantages!
Pros:
Compact and is the perfect size to use as a rear buttstock for various 88 Gram and or HPA rifles.
Smaller tank means if you are using a foot pump it won’t take all day to fill up :)
Comes with adapter so can be used with regular HPA and 88 Gram CO2 systems.
Regulated to 1100 psi so should perform better in terms of max velocity and consistency compared to CO2 which is around max 800-900 psi with velocity being effected by cool down.
Not effected by colder temperatures compared to CO2.
Once you have this tank the cost is virtually nothing to shoot compared to expensive 88 Gram CO2 cartages. You just need to buy your pellets or BB’s.
Cons:
Still takes a while to pump up using a foot pump system.
Higher initial cost ($195) than simply buying 88 gram CO2 cartages when you need them.
Will need access to a pump or compressor to use it.
Doesn’t look as good as the supplied buttstock at least with the Sig Sauer MCX and MPX.
Comments:
I guess the question is who is this for? If you are a casual shooter that perhaps owns the Sig MPX or MCX or even another 88 Gram CO2 Air Rifle that the Air Venturi 3000 PSI with Stock & Adapter Aluminum Tank would work with then this may be a bit expensive especially if you don’t have a way to pressurizer the tank at home. On the other hand if you already have a foot pump or air compressor or easy access to one and maybe you have other HPA or CO2 based airguns this tank will work with then it’s kind a no brainer to get it. Maybe you juts want a system that gives you maximum and consistent velocity no matter how cold it is outside. All good reasons to get one in my books.
In this Update Preview Unboxing Video I take a look at 5 products that came across my table and that I have not reviewed so far on the Replica Airguns YouTube channel.
First I show off an HPA tank from Air Venturi that works perfectly for the Sig Sauer MPX and MCX Pellet Rifles allowing for more consistent fps and I would image a higher overall fps? We will find out when I test it out in the replica Airguns Indoor Sea Can Airgun Range.
13 Oz Aluminum
10 Inches Long
2 Inches Diameter
Integrated Pressure Gauge
Includes Buttstock
CO2 Adaptor Included
3000 PSI Fill
1100 PSI Regulated
Next I take a look at the KJWorks M9A1 GBB Airsoft Pistol, I hover revived the CO2 version before but this version comes with the Gas magazine rather than the CO2 mag for those that prefer gas operated Blowback Airsoft Pistols. Because of the slightly lower FPS the Gas version comes with a barrel extension to make it Canada import friendly.
6mm Airsoft BB’s
Green Gas / Propane
370 fps
25 Round Magazine
2 Pounds
Probably one of the most interesting product I look at in this video at least for me is the EMG JW3 Combat Master GBB Airsoft Pistol. This Airsoft pistol is mainly aluminum with some polymer based off of the 2011 STI and was featured in the 2019 John Wick 3 Film. I’m really looking forward to testing this one out in the Sea Can Replica Airguns Airgun Range!
6mm Airsoft BB’s
Green Gas / Propane
9.4 Inches
366 fps
28 Round Magazine
2.4 Pounds
Moving along to another Air Pistol I finally get my hands on the Crosman P1 which is really just a KWC PT92 4.5mm Blowback CO2 BB Pistol but with Crosman Branding and an included laser. Since I have never shot a PT92 BB Pistol with a laser I will probably make a Field Test Shooting Video to see how well it performs.
4.5 mm Steel BB’s
CO2 x 1
4.2 Inch Barrel
330 fps
19 Round Magazine
2.4 Pounds
Comes with Laser Sight
Last up I take a look at the ASG TAC-6 which is pretty much the exact same ASG TAC-4.5 CO2 Air Rifle I tested a while back but in this case the 6 refers to it being a 6mm Airsoft Rifle rather than a 4.5mm Steel BB Riffle. I am not sure I will do a full Table Top Video since these guns are virtually identical but just in different Ammo types but I hope to get outside and see how well it performs shooting at a bit more distance than the 30 foot indoor range I usually test my Airgun in.
I thought when I read the one mag instruction guide that I had a good idea on how to use it but there was one area I misunderstood. I thought I needed to pull the tab in and out several times to reload the magazine but in fact I only needed to pull it out once, then shale the magazine back and forth horizontally a few times and then I was good to go.
I also read some other comments that mentioned I didn’t have to take the magazine out every time I reloaded so in this video I test that out to make sure and then one last comment that rather than pulling the charging handle back each time I reloaded I could simply press the bolt release on the right side of the Airgun, and yes this is the case with the Crosman Full Auto rile series.
So here I go a second time in making sure I do it right this time!
I have been wanting to test out the Crosman Full Auto Quick Reload Magazine for a while now and finally got around to it. The weather was cooperating with me so I went outside for this one and setup a bunch of cameras to make the many many magazine reloads a bit more interesting for my viewers.
The Crosman Full Auto Quick Reload Magazine has a hopper that is said to hold around 300 4.5mm Steel BB’s which I can attest it does in fact hold at least 300 BB’s. The Crosman Full Auto Quick Reload Magazine like their regular Crosman Full Auto Magazines holds two 12 gram CO2 Cartridges, so the question is, will I be able to get through most of the 300 BB’s without reloading the CO2?
Watch my struggle a bit to figure out the exactly how to properly use the Crosman Full Auto Quick Reload Magazine and then quickly eat through 300 or so BB’s blasting pop cans down range!
My systems setup for a more powerful airgun as I was shooting .22 caliber lead pellets with about 11-12 foot pounds of energy. Direct hits passing through the 3/4 inch cut outs had no problem laying down the metal paddles and resetting the paddles was a lot easier than I though it would be even way back 50 feet.
I did not have my Sig Sauer Virtus PCP .22 Caliber Air Rifle perfectly sighted in so I did have to aim low and to the left which made it a bit harder dropping the plates but I did manage to get the job done at least for providing a decent test video fo the Rx Target Systems for the purposes of this video.
Make sure to not only watch my Field Test Shooting video included in this post but also checkout my Rx Target Systems Preview Video where I show it up and close and also go into more details on the Rx Target Systems and how modular and versatile it really is.
I want to thank David Bitkowski from Rx Target Systems for providing me with this sample unit to share with the Replica Airguns community. This video is only a Preview video as I wanted to get the RX Target System out there before I follow up with my actual Table Top and Shooting Videos for it.
For now here are some of the key points I want to get out to everyone:
Mission: Rx Target Systems are meant to bridge the gap between firearms and airguns. They allow high precision shooting on a reactive, three- dimensional, rugged target that can be carted around in a back pack. What makes Rx Target Systems unique is that it is a system. It is so modular and adaptable with interchangable faceplates and paddles. Rx Target Systems are not going to break or get dented or dissembled on the range as many of the lighter gauged steel targets on the market today vs today’s high powered airguns.
Modular
One base allows interchange of faceplates for different target configurations
One threaded axel allows interchange of paddle from 10 gauge to 3/8 inch-thick paddles
Portable
Mount it on a shelf indoors
Mount it on a sawhorse outdoors
Carry it in a backpack or duffle bag- its 10 pounds
Rugged
Solid steel design
Faceplates from 10 gauge to ¼ inch thick
3-Dimensional
Faceplate is offset from paddles
Clipping the aperture does not guarantee a score
Intentions of target configurations
Standard 1 inch bulls.- represents kill zone of many small game at 30 yards, great for sighting in prior to the hunt. Also is ¼ scale of bull used in rapid fire pistol when shot from 8.3 meters. (25 meters distance/100mm bull)
1.2 inch bulls- represents the 4-10 ring of the NRA 10 meter air rifle target. Gears the shooter to consistently hitting the “black” of that target on paper
AAFTA style- represents common kill zones found in American Airgun Field Target Assosciation using 1.5”, 1”, ¾", ½", and 3/8”.
WFTF style- represents common kill zones found in World Field Target Federation using 15mm, 25mm, and 38mm apertures
10-15- Inspired by customer request, uses 10mm and 15mm apertures. High-Precision shooting.
In this SHOT Show Las Vegas 2020 Interview Video Scott takes us through a range of new products from Air Venturi.
Scott and I talk about the Air Venturi TR5 and how it came about to fill the hole the Baikal MP-61 left behind. We also talk a look at some new Air Rifles, a pumper called the Butterfly with a super cool linkage based system that makes pumping a lot easier. A PCP side lever cocking Air Rifle that I’m not even sure has a name yet but will be available in .177 .22 and .25 caliber pellet for around $299 US.
The only Air Venturi replica we looked at is a new Springfield Armory under lever Spring Piston Air rifle modeled after the M1A. Last up Scott went showed us how the Bada Bang targeting system is shaping up and looks to be almost ready for production.
We had a lot of great new Airguns that I reviewed this year at Replica Airguns. Some of them really stood out to me and so I made a video showing my Favorite Replica Airgun Picks of 2019. Of course there where many other Airguns that could has just as easily made this video but I had to draw the line somewhere and pick the ones that in my opinion where the best of 2019. Make sure to watch my Vimeo video where I go into some more details on why I liked each Airgun.
Below is a list of the top Replica Airgun Picks of 2019:
In a way I have already Field Tested the Air Venturi TR5 .177 Caliber Pellet Rifle, well at least in the Baikal version. The Air Venturi version is pretty much a knock of of the Baikal IZH MP-61 which not only look a lot alike but also performed very similarly for me, checkout my Baikal YouTube Video Review for comparison. All that said we can not get Baikal products here in North America anymore so it’s great that Air Venturi has recreated a very similar product for us to have in Canada and the US.
Moving on to the Field Test Review for the Air Venturi TR5 .177 Caliber Pellet Rifle, I first placed 5 shots through my Chronograph to see if the Air Venturi TR5 .177 Caliber Pellet Rifle did in fact shoot around 500 fps and in fact I was able to get all 5 shots up and over 500 fps averaging around 513 fps. Still within our Non-regulated firearm laws here in Canada since we where still under the 4.2 foot pound energy limit using 6.9 grain pellets.
As mentioned before when I shot the Baikal IZH MP-61 I was able to get very similar results but I did have an optical scope on the Baikal IZH MP-61 as compared to the Air Venturi TR5 .177 Caliber Pellet Rifle where I just used the open sights. In my opinion the Air Venturi TR5 .177 Caliber Pellet Rifle is good value for your money offering a unique design with excellent performance and getting as much power out of a pellet rifle as you can get here in Canada without requiring a firearms license.
Pick one up in our Canada or US Online Replica Airguns stores!
Again I have some new products to show everyone. Some we got a bit of a preview of when I was at SHOT Show 2019 earlier this year but now I have them in my hands to show off and of course will be doing full Table Top and Filed Test for anything new as soon as I can get to them.
Starting with Sig Sauer, they sent me their brand new Sig Sauer P365 CO2 Blowback BB Pistol. This was probably one of my favorite new Air Pistols at SHOT Show simply because it is so small and somehow Sig was able to find a way to put a full size drop out metal magazine that holds both the CO2 and BB’s in it. This is one I am really looking forward to testing out in the Indoor Sea Can Airgun Shooting Range.
Another fantastic product is Crosman’s DPMS Full Auto CO2 BB Rifle which was pretty much perfect the first time around. Well at SHOT Show this year Crosman updated it a bit mainly with some cosmetic changes and now is offering the Crosman MPW, a slightly shorter version of the DPMS and now with an AR Compatible Stock for customizing your Crosman’s MPW Full Auto CO2 BB Rifle.
So maybe not as exciting… I also take a look at a NBB CO2 BB Makarov from KWC that is pretty basic but is much less expensive and will offer higher FPS and more shots per CO2 being that it is Non-blowback Airgun. It will be interesting to see how it compares performance wise to the KWC Full Blowback CO2 BB version.
Last but also super cool and I know it’s not really as Airgun related but still something I think everyone will be interested in is the Pocket Shot Pro Arrow Pouch with D-Loop. I reviewed the Pocket Shot “Slingshot” a while back, this new product allows you to use standard Arrows with their new Arrow Pouch getting around 40 pounds of pull and it comes with a trigger release. By the way the Pocket Shot Pro Arrow system is legals to hunt deer with in most US States, I’m not sure about Canada but perhaps here too?
In this December Update Video I wish everyone a Merry Christmas and Happy New Year. If you have other beliefs and perhaps don’t celebrate Christmas in the traditional Canadian fashion then I wish you a Happy Holiday!
I received a number of products lately and really don’t have time to do full reviews of them as the Holliday season is on us which is going to limit how many videos I can pump out over the next couple of weeks so hopefully this Update video will keep everyone excited about the future Replace Airgun Videos.
Here are the items I talk about in this December 2018 Update Video:
A while back I did review of the 1/4 Scale Mini Replica Guns distributed by Goat Guns. Goat Guns sent them to me for review and at the time we where not selling them in our Replica Airguns Store. Recently we got some of our own 1/4 Scale Mini Replica Guns that I would say are pretty much exactly the same as the Goat Gun Line but with different packaging since they are not distributed by Goat Guns.
The good news is you can get the same product from us now in our Canada and US Replica Airguns Stores! And ours are even pre-assembled for you but if you like you can take them apart similarly to a real gun.
These 1/4 Scale Mini Replica Guns are made out of a lot of metal where you wound find it on the real steel counterpart and most parts operate the same too like removable magazines, working triggers and safety’s, Even the dust covers on the M4’s open when you charge the mini gun!
My struggle for a reliable and dependable Chronograph to test the feet per second velocity of the airguns I test in my indoor Sea Can shooting range has been going on for some time now. My original Chrony Chronograph just never gave me consistent results and over time it pretty much became useless so I ended up shooting the living tar out of it (Watch that video) and replacing it with a slightly better Chronic Chronograph.
The new Chrony Chronograph setup in my indoor Sea Can Airgun range worked really well for me especially using the LED lighting system I added to it (Made by Caldwell). But not even two years later my new Chrony Chronograph just flat out died on me, the screen went all garbley-goop and became unreadable. I tried a new battery and looked everywhere to see if there was a factory reset I could do but was not able to get it working again :(
Well I figured I invested enough money buying Chrony Chronographs with not so good results from them so it was time to look to another company for my airgun velocity testing needs. I ended up going with the Caldwell Ballistic Precision Chronograph which by the way is compatible with my LED lighting system since it is all made by the same company. I paid $149 Canadian for my Caldwell Ballistic Precision Chronograph which is pretty good and it even came with a super long cable to connect a smart phone that works on both iPhone and Android phones using the Caldwell App to display velocity readings in the their smartphone App.
I will be making a "test" video where I shoot several airguns I have not Chronographed yet to see how my new Caldwell Ballistic Precision Chronograph works so stay posted for that video coming out very soon!
On another note I upgraded my Drone just a little, I previously bought the Yuneec Breeze 4k Drone to use in my future videos to get some new interesting camera angles while I do some of my outdoor shooting and to be honest the quality is really good on it. Probably good enough for what I'm doing, but for only a couple hundred dollars more I was able to buy the DJI Spark which is by far a much better drone than the Breeze in many ways. Video is more stable and "follow me modes" are way more reliable to name a few things the DJI Spark does that are important to me.
You'll get to see video from the DJI Spark shortly in fixture videos. This little Drone is crazy!
I made a similar video about how to hold your airgun a while back but sometimes they get a bit buried in all the video I make. I feel it's really important how you grip your gun even if it's only an airgun with very little kick or recoil. Proper pistol grip is something you should use no matter what so that you can carry it forward to what ever gun you are shooting.
More kick or recoil means a firmer grip is required to hold the gun so when shooting a powder burner with lots of kick grip becomes even more important.
In this video I go over the proper two handed grip to use when holding a pistol, which hand to hold lose and which had to grip tight, how to overlap your fingers and thumbs.
