Another Field Test Shooting Video Review coming for the Replica Airguns Sea Can Indoor Airgun Shooting Range! In todays Shooting Review I test out the Schofield No. 3 CO2 BB-Pellet Revolver using both 4.5mm 5/1 grain Steel BB’s and .177 Caliber 6.9 grain Lead Pellets to see how well they perform in velocity and accuracy. As always I use a brand new CO2 for my velocity testing and for reference the temperature during my testing in the Sea Can was 23 degrees Celsius or 73 degrees Fahrenheit. For my accuracy portion of the shooting test I use a rested and seated shooting position shot 30 feet away from my fresh paper targets.
Starting off with the velocity or power potion of my Field Test Shooting Video for the Schofield No. 3 CO2 BB-Pellet Revolver. I first used the 4.5mm Steel BB shells and shot 3 rounds through my Chronograph averaging 369 fps. I then loaded up the Schofield No. 3 CO2 BB-Pellet Revolver with pellet shells and again placed three .177 caliber lead pellets through my Chrony and got a very similar result with an average of 361 fps. Keep in mind the lead pellets where 6.9 grain versus the steel BB’s at only 5.1 grain, so the lead pellets will be carrying more raw energy at the point of impact even though they where going just a tad bit slower than the steel BB’s.
In terms of accuracy both rounds performed about the same shooting at my paper target 30 feet away. Since the Schofield No. 3 CO2 BB-Pellet Revolver has a 6 round cylinder I shot 6 sounds for each test, 6 steel BB’s and then 6 lead pellets. I also changed the targets for each type of ammo between reloading. I found the Schofield No. 3 CO2 BB-Pellet Revolver shot fairly close to the bullseye, l but with both the Steel BB’s and lead pellets I got one outlier that spread out my groupings significantly, the other 5 rounds where all close being about 2 inches apart? Perhaps it was a bad or misshaped round, or maybe even me ;) I did notice the lead pellets seemed to have a really nice 4 round group out of the 6 that all fell within the bullseye. Hard to really say if BB’s or pellets performed better than the other one at least in my testing.
Overall the Schofield No. 3 CO2 BB-Pellet Revolver shot well for me, the trigger is nice and short and light making placing your shots easy, of course since it is a single action only trigger you kind of need to reset yourself between every shot which can effect groupings just a bit. Since the barrel is not rifled with no danger of damaging the rifling, you can really shoot what ever ammo type you feel like shooting or have on hand and since Schofield No. 3 CO2 BB-Pellet Revolvers get about the same speed and accuracy then it really doesn’t matter that much at the end of the day!
Type: BB/Pellet air revolver. Manufacturer/Distributor: Bear River. Model: Schofield No. 3 Materials: Mostly metal with plastic grips. Weight: 2.4 pounds. (1089 grams) Barrel: 7 inch (178mm) smooth bore barrel. Propulsion: 12 gram CO2. Action: Revolver, single action only. Ammunition Type: 4.5mm steel BB's and .177 Cal. Pellets. Ammunition Capacity: 6 rounds. FPS: 445fps.
Trigger Pull: The trigger pull on the single action only Schofield No. 3 CO2 BB-Pellet Revolver is what you would expect from a pistol of this design. Like the Colt Single Action Army the trigger pull is very short, light and crips, perfect for taking your time and getting a precise shot on target. You will of course have to cock the hammer manually before each shot ao no real action shooting.
Accuracy: I have not tested the Schofield No. 3 CO2 BB-Pellet Revolver in the Replica Airguns Sea Can Indoor Airgun Range but plan to get to it shortly. I will test out both 4.5mm Steel BB’s and some .177 caliber lead Pellets and see how the different ammo types effect both power and accuracy. Keep in mind the Schofield No. 3 CO2 BB-Pellet Revolver has a smooth bore barrel but I am pretty sure pellets will still perform well at 30 feet away.
Build Quality: The Schofield No. 3 CO2 BB-Pellet Revolver is built a lot like the Webley MK VI .455 CO2 Shell Loading Revolver line, perhaps even made in the same factory in Taiwan? The Schofield No. 3 CO2 BB-Pellet Revolver is pretty much an all metal construction other than the plastic grips and any internal seals. The fit and finish is excellent with a great overall weight in the hand. The pistol grips is a lot like what you have with the Colt Single Action Army pistol but the Schofield No. 3 CO2 BB-Pellet Revolver is a lot more front end heavy because of its beefy barrel.
Realism: In terms of replicating a real steel Schofield No. 3 CO2 BB-Pellet Revolver for sure looks and feels that part. The reassessed barrel and well hidden CO2 screw don’t give anything away that the Airgun version is not the real deal. But as with all of these shell loading Airgun Revolvers, the shells are actually closer to a .380 Caliber in diameter rather than a 45 which is what the real steel Schofield No. 3 CO2 BB-Pellet Revolver would be designed for.
If you are like a bulky revolver with good weight to it then the Bear River Schofield No. 3 is it.
Can shoot Steel BB’s or Pellets since it comers with both shell types.
Recessed barrel.
Well concealed CO2.
Shell loading design that loads from the back so no need to remove shells if you wish not to.
Single Action Only hammer and trigger action feel good, nice and light with short take-up and release.
Fairly discreet safety location right behind the hammer so easy to get at.
Super easy to load, pellet shells can even be reloaded with shells in the gun if you are using the pellet shells.
Really like the Nickel Finish on this gun.
Can get simulated Ivory grips for it if you prefer that look.
Cons:
Sights are not adjustable.
Warning instructions on side of the frame.
Barrel is not rifled for pellet use?
Only a Single Action Only Hammer and Trigger but true to the style of the gun.
Comments:
Yet another classic shell loading CO2 BB Revolver, and again the more the merrier in my option! I like that you get 12 shells with our kit version, 6 removable shells for 4.5mm Steel BB’s and 6 removable shells for .177 caliber Pellets. The Schofield No. 3 CO2 BB-Pellet Revolver is for sure a hefty revolver but the pistol grip is not super large so even people with smaller hands should not have a problem shooting the Schofield No. 3 CO2 BB-Pellet Revolver. The real problem is deciding which Shell Loading Airgun Revolver to buy now since we have so many to choose from… Classic or modern, nickel or black, or perhaps weathered?
My Table Top Review for the Schofield No. 3 CO2 BB/Pellet Revolver:
I don’t do a lot of paintball gun reviews, they just don’t come across my table all that often so it’s a lot fo fun when I do get the chance to shoot some beefier caliber ammunition in the Replica Airguns Sea Can Indoor Airgun Shooting Range. Of course I use rubber ball ammo rather than standard paintball rounds in order to keep the mess to a minimum.
I have not done my Table Top YouTube Video Review yet for the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun but you can checkout a Preview Video for now. In Summary the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun is a pretty much exactly what the name says. It’s basically a sawn off pistol grip styled double barrel shotgun that uses CO2 and shoots .68 caliber paintballs. You have a selector for shooting either out of the left or right barrel or if you want to can even both at the same time but this really slows down the fps so I would not advise it with the 200 fps version that I was testing with.
Now on to the actual testing of the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun! As alway I like to find out how close to the factory claimed fps I will get. Umarex claims around 200 fps for this version which is around 7.5 Joules of energy, apparently there is a 16 Joules version that shoots closer to 300 fps but we do not carry it at least right now. I put a couple fo rounds through my Umarex T4E HDS Double Barrel CO2 Paintball Shotgun using rubber ball paintballs which will be a little bit heavier than a standard paintballs and my first shot yielded 180 fps, my second shot was slightly higher at 184 fps so pretty close to the claimed 200 fps and that was in not the warmest of environments since the temperature in the Replica Airguns Sea Can Indoor Airgun Shooting Range was only 16 Degrees Celsius (60 Degrees Fahrenheit).
Next up it was time to see how the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun performed shooting at a target setup 30 feet away. Since there are no actual sights on the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun I had to kind eyeball it and as I shot it more and more I was able to get my shots closer to the center of the target. The Umarex T4E HDS Double Barrel CO2 Paintball Shotgun is not a tac driver but at 30 feet out you should be able to hit an 8-10 inch target pretty consistently. I don’t recommend using the double shot option since the same amount of CO2 is applied to both rounds that would normally be applied to one round decreasing the fps by about half making the paintball rounds shoot a lot slower and not really being that effective. This may be an option with the higher 300 fps version of the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun.
So all in all I had a lot of fun shooting the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun, it’s kind of like a big boy Nerf Gun that you can take onto the paintball field if you wanted to. For home defense I think it is a bit underpowered but there may be a little bit of shock factor that could slow someone down or deter them enough to either give you time get away or take shelter somewhere safe. Maybe using the pepper rounds would work OK in this situation? Either way the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun is a really cool and unique CO2 Airgun that is not overly expensive and a welcome addition to any Airgun enthusiasts collection.
Starting off with my velocity power test using my Caldwell Ballistic Precision Chronograph, I was able to get really close to the factory claimed fps of 360 with an average of 347 fps. Shooting conditions where decent in the See Can compared to outside temperatures in late October but still not that warm at only 16 Degrees Celsius (60 Degrees Fahrenheit), a lot warmer than outside but still not as warm as your typical summer day. In warmer conditions I am sure I would have hit the claimed 360 or even high fps with the Umarex Glock 19X CO2 Blowback BB Pistol.
Next for my Field Testing , I placed 10 shots into a paper target with my Umarex Glock 19X CO2 Blowback BB Pistol from 30 feet down range using my standard seated and rested shooting position (Seated in the back and rested on a sand bag up front). I was able to get right around a 2 inch 10 shot group, not bad at all! The Umarex Glock 19X CO2 Blowback BB Pistol did shoot a little bit high and to the left which for some reason is common with most CO2 action airguns and I know it’s not entirely me since others have commented the their airguns shoot a bit to the left in most cases. Elevation was pretty close at 30 feet but just a tad high.
The Umarex Glock 19X CO2 Blowback BB Pistol is very similar to their Umarex Glock 17 3rd Gen in terms of their mechanical build and function since both use the same magazines and have that semi blowback action but I can say the Umarex Glock 19X CO2 Blowback BB Pistol not only looks better in my opinion but the slide is improved as it seems to have a less metallic sound and the slide wiggle is very minimal. The Umarex Glock 19X CO2 Blowback BB Pistol also did not lack in the performance department getting really close to the the claimed 360 FPS while shooting about the same 10 round grouping of 2 inches which is about what I expect for an action BB shooter. Now we have a bunch of Umarex Glocks to chooses from, checkout our Replica Airguns Canada and US Online Stores for Glock airguns and find one that’s right for you!
Type: Blowback CO2 BB Pistol. Manufacturer: Distributed by Umarex. Model:Glock 19X. Materials: Metal & Polymer. Weight: 1.5 pounds (662 grams). Barrel: Smooth bore 3.36 inch barrel (85.3mm). Propulsion: CO2 x 1. Action: Semi auto blowback, double action only trigger. Ammunition Type: 4.5mm steel BB's. Ammunition Capacity: 18 round drop out full size metal magazine. FPS: Claimed 360.
Trigger Pull: The trigger pull on the Umarex Glock 19X CO2 Blowback BB Pistol is what I would call a double action trigger mainly because there is an indexing of the BB from the magazine into the breach area every time you pull the trigger which means the take up is longer thanks a standard Glock take up and there is a little bit of friction from the mechanical mechanism that indexes the BB making the trigger feel more like a double action only trigger.
Build Quality: TheUmarex Glock 19X CO2 Blowback BB Pistol seems to be really well made. Fit and finish are nice and slide wiggle is minimal. There is a bit of a clanky sound when the slide cycles but not as bad as the Umarex Glock 17 Gen 3 CO2 Blowback BB Pistol. I also think the Coyote finish is the nicest looking with its black on tan two tone look.
Realism: The Umarex Glock 19X CO2 Blowback BB Pistol absolutely looks the part of a Glock 19X, sitting on the table and even holding it in your hand you are going to think it's the real deal until of course you drop the magazine and see that it is a CO2 mag. Mostly everything operates like a real Glock 17 but the slide is not a full blowback meaning it only goes back about 3/4 as much as a real Glock 17 slide would. One other noticeable difference is the ability to quickly field strip the Umarex Glock 19X CO2 Blowback BB Pistol, you will need to remove a pin since the take down tabs are non functioning and moulded into the frame. Available From: The Replica Airguns Store.
Pros:
Nice weight and feel to it, build quality seems good.
Really nice looking replica of the real steel Glock 19X, love the Coyote color.
Fully Glock licensed.
Easy to see white dot sights front and back.
Recessed barrel for added realism.
Accessory rail for adding a laser or tactical light.
Full size drop out metal magazine that holds the CO2 and 18 4.5mm steel BB’s.
Safety built into the serial number plate area keeps it well hidden.
Warning instruction are nice and discreet under trigger guard
Not bad feeling double action only trigger as the blowback pre-cocks the internal hammer/strike.
360 fps is decent for a blowback BB gun.
Cons:
Does have blowback action but not full blowback.
Slide sound is a bit clanky but not as bad as the 17 Gen 3 Blowback.
Sight are non-adjustable which is common with low cost action shooters like this one.
Would have liked to have seen more pristine packaging from Glock over the plastic clamshell
Comments:
It’s great to see Umarex expanding their live of Glock licensed Airguns and the addition of the Umarex Glock 19X CO2 Blowback BB Pistol is welcome! Some of you are not going to like the semi blowback action but it does mean you get higher fps and more shots per CO2 while still getting that simulated recoil form the blowback action. I honestly thing the Umarex Glock 19X CO2 Blowback BB Pistol is one of the most attractive Glock Airguns with it’s Coyote Tan frame and slide with black highlights, I also like the compact size for its shortened frame and slide over the Umarex Glock 17 Gen 3 CO2 Blowback BB Pistol. So many to choose for now but I guess that a good thing or perhaps just get them all!
I though I would feature the fact that we recently added some of the Tokyo Marui product line to our Canada Replica Airguns Store. Tokyo Marui is said to be one of the best Airsoft products on the market and they have been around for a while so they have had time to get it right! As Tokyo Marui is a Japanese based company they are restricted to only being able to use plastic frames and slides but even with this limitation the Tokyo Marui products that I have personally looked at are extremely well made.
I don’t often make many Paintball Review Gun Videos let alone Shooting Videos so this one is a bit different than the norm. Lucky for me I have some .43 caliber Rubber Paintballs that I can use in my Indoor Sea Can Shooting Range so as not to make a mess of things. As per usual I like to use a brand new 12 Gram CO2 Cartridge for my testing and for your reference the temperature was right around room temperature or 21 degree Celsius, 69 degrees Fahrenheit.
First up I generally perform my Chronograph test to see what the real world velocity or fps is for the Umarex T4E HK 416 Training Marker CO2 Paintball Rifle. I shot a short string of rubber rounds through my Chronograph and was able to get a 280 fps average with the Umarex T4E HK 416 Training Marker CO2 Paintball Rifle. This is plenty enough power for the intended target down range to feel the paintball effect without causing too much trauma.
With the remaining 10 rounds in my Umarex T4E HK 416 Training Marker CO2 Paintball Rifle magazine, I then setup a brand new paper target 30 feet down range and using a rested and seated shooting position and carefully unloaded the Umarex T4E HK 416 Training Marker CO2 Paintball Rifle into the target. I was a bit surprised to see the rounds spread out a fair amount perhaps as much as 10-12 inches but at least half where in the target rings.
I would not recommend the Umarex T4E HK 416 Training Marker CO2 Paintball Rifle as a long range paintball marker but it would be perfect for close quarters ultra realistic simulations. I would like to give actual .43 caliber paintballs a try outside to see if accuracy would be better, maybe the rubber balls grip the barrel a bit too much causing some random and unexpected spinning to occur? Either way the Umarex T4E HK 416 Training Marker CO2 Paintball Rifle is a really unique and fun Paintball Gun to shoot, maybe not for everyone but if you want the most realistic Paintball Marker then it would be a great option.
In this Field Test Shooting Video I focus on Umarex’s latest CO2 Blowback BB Airgun, the Umarex Glock 17 4th Gen CO2 Blowback BB Pistol. We have been waiting a while for this one to ship and now that it’s here I really want to get to shooting it and finding out if it performed as good as it looked and felt.
I loaded up my Umarex Glock 17 4th Gen CO2 Blowback BB Pistol with a brand new 12 gram Sig Sauer CO2 cartridges along with some 4.5mm RWS 5.1 grain Zinc coated BB’s and began the Chronograph portion of my Indoor Field Test Shooting Video. The temperature was not overly warm sitting right around 19 degrees Celsius or 66 degrees Fahrenheit. Umarex claims roughly around 300 fps from the Umarex Glock 17 4th Gen CO2 Blowback BB Pistol but I was able to get just a bit high with my 5 shots through the Chronograph averaging 310 fps.
I then put up a paper target 30 feet down range, reloaded my full size drop out metal magazine with 10 more steel BB’s and proceeded to carefully place the 10 shots into the target using a rested and seated shooting position. I was able to get around a 3.5 inch grouping but I feel I could have done better since several rounds actually shot one on top of the other. The Umarex Glock 17 4th Gen CO2 Blowback BB Pistol did shot just a little bit low and to the left but not a lot.
Type: Blowback CO2 BB Pistol. Manufacturer: Distributed by Umarex. Model:Glock 17 Gen 4. Materials: Metal & Polymer. Weight: 1.7 pounds (771 grams). Barrel: 3.6 inches metal non-rifled. Propulsion: CO2 x 1. Action: Semi auto blowback, single action only trigger. Ammunition Type: 4.5mm steel BB's. Ammunition Capacity: 18 round drop out full size metal magazine. FPS: Claimed 300.
Trigger Pull: The trigger pull on the Umarex Glock 17 Gen 4 CO2 Blowback BB Pistol is single action only so you will need to rack the slide first to not only chamber a 4.5mm Steel BB in the breach area but to also cock the internal striker. There is a working trigger safety on the Umarex Glock 17 Gen 4 CO2 Blowback BB Pistol and you’ll also find the Glock 17 Gen 4 has a nice short and light trigger as you would expect similar to the real steel Glock. Perfect for fast action shooting!
Accuracy: At this point I have not shot the Umarex Glock 17 Gen 4 CO2 Blowback BB Pistol so I can only quote what Umarex is saying in terms of FP2 which is 300. That sounds reasonable based on other Airguns like this that have that full blowback action since much of the CO2 gas is used to work the action of the slide. This not only reduces how many shots you can expect o get out of a single 12 gram CO2 cartridge but a reduction in power over non-blowback or even partial blowback CO2 Airguns.
Build Quality: TheUmarex Glock 17 Gen 4 CO2 Blowback BB Pistol looks to be well made overall with metal and plastic parts where you would find them on a real steel Glock 17 Gen 4. Fit and finish are nice and the slide wiggle is next to zero. The slide spring is very heavy and the sound of the slide when racked and released does not have that cheap metallic sound some blowback Airguns have. I am expecting some pretty decent blowback action recoil from the Umarex Glock 17 Gen 4 CO2 Blowback BB Pistol when I do my Field Test Shooting Review!
Realism: The Umarex Glock 17 Gen 4 CO2 Blowback BB Pistol 100% looks the part of a Glock 17 4th Generation, sitting on the table and even holding it in your hand you are going to think it's the real deal until of course you drop the magazine and see that it is a BB/CO2 mag. Mostly everything operates like a real Glock 17 including the slide catch release, trigger safety, magazine release and even the take down switches for quick field stripping and access to the adjustable hop-up, yes it is adjustable. Available From: The Replica Airguns Store.
Pros:
Good weight and feel to it, build quality seems very good.
Really nice looking and full featured replica of the original Glock 17 Gen 4.
Fully Glock licensed through Umarex.
Easy to see white dot sights front and back.
Recessed barrel for added realism.
Accessory rail for adding a laser or tactical light.
Full size drop out metal magazine that holds the CO2 and 18 4.5mm steel BB’s.
Slide spring feels heavier than most full blowback Airguns, should have a heavy blowback recoil effect.
Safety built into the serial number plate area keeps it well hidden.
Comes with additional Backstraps for different sized hands.
Warning instruction are nice and discreet under trigger guard.
Great feeling single action only trigger as the blowback pre-cocks the internal hammer/strike.
300 fps is decent for a full blowback BB gun.
Cons:
FPS could be higher but fairly inline with other full blowback CO2 air pistols.
Sight are non-adjustable which is common with low cost Airguns like this one.
Would have liked to have seen more pristine packaging from Glock..
Comments:
I know everyone has been waiting for Umarex to release the Umarex Glock 17 Gen 4 CO2 Blowback BB Pistol and here it is finally, does it live up to all the hype and excitement? So far without shooting it I have to say yes, I am very pleased with how the Umarex Glock 17 Gen 4 CO2 Blowback BB Pistol looks and feels. There is not too much more you can ask for in a replica Airgun of any kind… it looks like the real steel version, it feels like there real steel version, it functions like there real steel version. Hopefully it shoots just as well! If you haven’t bought one of the Umarex Glocks so far then this one is the one to have, but I say why not have them all :)
The Webley Nemesis is a really interesting CO2 Pellet Pistol, so far I have not reviewed an Airgun like it. Yes I have reviewed bolt action CO2 Pellet Pistols in the past but not one with a rotary magazine for much quicker followup shots. This is by no means as quick as a semi auto shooter but being able to quickly work the bolt action without having to manually place a pellet in the breach area sure does speed things up.
On the box Webley claims up to 420 fps with the ,177 caliber version the Webley Nemesis is a really interesting CO2 Pellet Pistol I was testing and I was able to get an average of 430 fps using a brand new CO2 along with RWS 6.9 grain lead pellets. I did find the RWS pellets I was using did not feed all that well perhaps because they had a fairly narrow waist on them which does effect the way pellets are held in the rotary magazine. The temperature was fairly normal at right around room temperature.
For my accuracy portion of the Field Test Shooting Video for the Webley Nemesis is a really interesting CO2 Pellet Pistol, I switched to Sig Sauer .177 caliber lead pellets and they worked much better in terms of chambering cleanly for me. I found the Webley Nemesis is a really interesting CO2 Pellet Pistol shot a bit high on my paper target placed 30 feet away, so I set my sights on the bottom ring which placed almost all my 14 shots right in the bullseye. My 14 shot string was grouping around 1.5 inches but I am sure the Webley Nemesis is a really interesting CO2 Pellet Pistol could shoot quarter sized objects at 30 feet downrange all day long once you get use to it.
The trigger on the Webley Nemesis Bolt Action CO2 Pellet Pistol is one of the highlights of this air pistol, it really feels great. Combine this with nice high consistent fps and excellent accuracy and the Webley Nemesis is a really interesting CO2 Pellet Pistol is a great target shooter with potential for up close small pest control.
I’m going to start off by saying this Field Test Shooting Review for the G&G GPM1911 GBB Airsoft Pistol did not go all that well as I had some complications with this Airgun when chambering rounds. I am pretty sure it is magazine related and hope to try a different magazine with it soon. I say this because I am following through with my review regardless of my initial results to demonstrate that not all Airguns perform as expected during my reviews and sometimes you get a lemon even with a good quality brand like G&G.
I am fairly certain the defect in this case for the G&G GPM1911 GBB Airsoft Pistol was the magazine tip being too tight and not allowing an Airsoft BB to position all the way to the top of the magazine which means when the slide cycled and the nozzle was in position to push an Airsoft BB into the breach, it simple was hitting the top of the BB and pushing it even further into the magazine. All said and done I was able to test the fps and accuracy on target so let’s get on with my review.
Using .20 gram Airsoft BB’s with a fully filled propane gas magazine in my G&G GPM1911 GBB Airsoft Pistol, I was able to get 6 recoreded shots through my Chronograph averaging 319 fps. The slowest shot being 313 fps and the fastest shot hitting 330 fps. The temperature was right around room temperature so around 22 degrees Celsius or 72 degrees Fahrenheit.
As I was having issues with with the G&G GPM1911 GBB Airsoft Pistol chambering rounds with the .20 gram Airsoft BB’s. I was hoping that when I switched to a different .32 gram Airsoft BB for my target portion of this review that perhaps the different Airsoft BB’s would chamber better but they did not. To get through the target portion of my test, with each shot I had to drop the magazine, make sure the Airsoft BB’s was at the top of the magazine, rack the slide, insert the magazine and then release the slide. So as you can see I was resetting completely for each shot which does not always make for the tightest groupings. Surprisingly I was still able to get about a 1.5 inch grouping on my paper target setup 30 feet downrange using a rested and seated shooting position.
Not all reviews go as planned but you still have to make the best of it. I really feel the G&G GPM1911 GBB Airsoft Pistol is a good gun overall even though mine did not perform that well for me. When I was able to chamber a round it shot a consistent fps and placed Airsoft BB’s downrange accurately and very close to the bullseye. Perhaps simply by swapping out the magazine I will have a much more reliable Airsoft gun? I will have to get back to you on that one.
Type: Gas Blowback Airsoft Pistol. Manufacturer: G&G Model: GPM1911 Materials: Metal slide, frame & Magazine. Weight: 2.25 pounds (1020 grams). Length: 8.66 inches (22.0 cm) total. Barrel: 4.58 inches (11.7 cm),Metal non-rifled smooth bore. Propulsion: Green gas or propane. Action: Blowback, single action only. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 25 rounds. FPS: 300-330 fps.
Trigger Pull: The single action only trigger pull on the G&G GPM1911 GBB Airsoft Pistol is what you would expect from a traditional single action only 1911 trigger, a very short take-up and a crips and light release. Great for getting a lot fo shoots off quickly and accurately down range without making your trigger finger do a lot of work.
Accuracy: I have not done my actual Field Test Shooting video review for the G&G GPM1911 GBB Airsoft Pistol so I can into comment just yet but I will be making a Field Test Shooting Video for it as soon as I can and will post that here on the website and of course over on the Replica Airguns YouTube channel when I have it ready.
Build Quality: The G&G GPM1911 GBB Airsoft Pistol is in my opinion one for the nicer looking finishes wise and I would have to say it seems to also be one of the better quality 1911 Airguns out there, for sure a step up from a KWC blowback 1911’s and in line with what KWA and KJWorks is making these days which is good quality. The G&G GPM1911 GBB Airsoft Pistol is one of the heavier Airsoft 1911 Blowback Pistols which makes me think the metal is a bit higher quality where it needs to be. Tolerances are nice and tight and the blowbacks action is very heavy.
Realism: The G&G GPM1911 GBB Airsoft Pistol like most of these full blowback 1911 Airguns, Steel BB or Airsoft BB, is super realistic with an all metal build. All the real steel working parts like the slide catch release, back strap safety and pretty much everything else function as they should. The G&G GPM1911 GBB Airsoft Pistol even field strips like a traditional 1911 pistol. Not sure what you could do to make it more authentic for an Airgun?
Nice high capacity magazine compared to other GBB 1911 Airsoft pistols.
Heavier than most Airsoft 1911’s.
All parts fit nice and tight, tolerances are very good.
Working back-strap safety.
No ugly red tip.
Finish is really nice, gun looks really good.
Expect to get decent amount of shots per gas fill.
Micro Gas Filter and Whirl Cylinder Valve help to manage gas efficiency and reduced frost buildup.
Traditional adjustable Hop-up.
Full Size Dropout metal magazine pretty standard on Airsoft pistols.
Comes with high quality hard shell case and speed loader.
Cons:
Sights are pretty basic, no white dots and non-adjustable as you would expect on a 1911 A1.
Very simple Airsoft gun, no modern bits and pieces on it.
FPS could be a bit higher but fine for close quarters.
Comments:
The G&G GPM1911 GBB Airsoft Pistol is for sure one of the nicer 1911 A1 styled Airsoft pistols, inline with KWC and KJWorks. It does come in a little bit heavier and seems to have more blowback recoil action which is nice. All I need to do now is find out how well it shoots! If it’s not half bad then it is for sure worth the price which by the way is a little bit cheaper than a KWA or KJWorks 1911 and about the same price as a KWC 1911. So many choices I know but that’s a good thing :)
My Table Top Review of the G&G GPM1911 GBB Airsoft Pistol:
Trigger Pull: The trigger pull on the KWC Makarov PM CO2 NBB BB Pistol is pretty decent for a double action only trigger, certainly light enough for some fairly fast action shooting without tiring your trigger finger too much. It would have been nice to have been able to cock the hammer for some slower and more precise single action shots.
Accuracy: So far I have not had the chance to test out the shooting performances for the KWC Makarov PM CO2 NBB BB Pistol, but I am expecting it to get sub 2 inch 10 shot groupings from 30 feet out and hopefully the KWC Makarov PM CO2 NBB BB Pistol will chronograph in close to the 400 claimed fps. Watch for my Field Test Shooting Video down the road.
Build Quality: The KWC Makarov PM CO2 NBB BB Pistol is a pretty basic CO2 BB Airgun, basically two metal halves of the frame screwed together and not a lot of working parts. It’s almost all metal except for the grips and hammer and has a good weight and solid feel to it so I expect it to hold up well over time. The fit and finishes seem just fine but it does have some noticeable seems going all around the Airgun where the two halves join together.
Realism: The KWC Makarov PM CO2 NBB BB Pistol at first looks like a real steel Makarov, it’s about the right size and weight, has a recessed barrel and no CO2 tab on the bottom so overall a good looking replica. It’s when you look a little bit closer look that you can really tell, from the lack of an open ejection port to the small screws on the right hand side of the KWC Makarov PM CO2 NBB BB Pistol. When you start to play around with it you will notice the hammer is plastic and only for show and of course not being a blowback gun the slide and slide catch release do not function at all.
Pros:
Full metal frame.
All metal full size drop out magazine that holds the BB’s and CO2.
Working safety, and magazine release.
Because it’s NBB it will get higher fps and more shots per CO2.
No ugly CO2 tab on the magazine.
Seems to have a decent double action only trigger.
Very affordable at around $70 Canadian.
Less moving parts means less to go wrong for longer reliability.
Cons:
No blowback operation so no single action trigger or simulated recoil.
Ejection port is not cut out and hammer is only for show.
Has those ugly screws on one side of the frame.
Comments:
Most of you probably already know I am a bit of a Blowback operation Airgun snob so when I review Non Blowback Airguns I am generally not as excited. What can I say, I just like the simulated recoil Blowback offers and the fact that Blowback Airguns will generally allow for a much lighter and shorter single action trigger. The plus side to a Non Blowback Airgun is going to be four main points: Usually a lower price tag, faster fps, more shots per CO2 and better longevity of the gun since there are a lot less moving parts to wear or break. It really come down to what you prefer, but the good news is you can have your choice of a Non Blowback Makarov like the KWC Makarov PM CO2 NBB BB Pistol or you can go with the blowback KWC Makarov PM CO2 Blowback BB Pistol. Or better yet, why not both!
My Video Review for the KWC Makarov PM CO2 NBB BB Pistol:
Lots of CO2 BB Rifles getting reviewed these days and that’s kind of awesome, I remember a few years back and we barely had any realistic Replica BB rifles available to us. Now we have an ever increasing list of choices from Historical to Modern.
Todays Field Test Shooting Video focusses on the Air Venturi Springfield Armory M1 Carbine CO2 BB Rifle, I have not done my Table Top Video yet for it but I did make a preview video where I show it around a bit and talk about some basic specs. In short the Air Venturi Springfield Armory M1 Carbine CO2 BB Rifle is a CO2 powered semi auto 4.5mm Steel BB firing replica of the Springfield Armory M1 Carbine. It holds the CO2 and 15 rounds of Steel BB’s in its full size drop out metal magazine. Available with a plastic or upgraded wood stock.
For the Field Test Shooting part of this review I tested out the power and accuracy of the Air Venturi Springfield Armory M1 Carbine CO2 BB Rifle by first shooting 5 rounds through my Chronograph to establish the Feet Per Second velocity. I then placed a fresh paper target 30 feet downrange, while using a rested and seated shooting position I fired off 10 rounds into the target to see how tight of a group I can get with the Air Venturi Springfield Armory M1 Carbine CO2 BB Rifle. I used a brand new CO2 along with 5.1 grain 4.5mm Zinc coated Steel BB’s. The temperature was a conservative 22 degrees Celsius or 71 degrees Fahrenheit.
During my Chronograph velocity test I was a bit surprised to only obtain an average of 335 fps from the Air Venturi Springfield Armory M1 Carbine CO2 BB Rifle. Air Venturi claims closer to 425 so I am not sure why it was nearly 100 fps lower than claimed but perhaps the CO2 did not pierce as well as it could have, that said 335 fps does get the job done when shooting targets 20-30 feet away.
In terms of accuracy I was very pleased with the Air Venturi Springfield Armory M1 Carbine CO2 BB Rifle, it kind of made up for the slower than expected feet per second by getting a sub 1 inch 10 round group and I am not a big fan of peep sights so I was really not expecting these results. Right out of the box the Air Venturi Springfield Armory M1 Carbine CO2 BB Rifle shot pretty close to the bullseye, just s slight bit to the left and about 1-2 inches high. The rear sight is adjustable for elevation so that can be taken care of pretty easy.
The purpose of my Field Test Shooting Video is to find out how the airgun being reviewed performs in terms of velocity and accuracy, and if the ratings on paper end-up being the same or close to the tested results. Crosman claims the Crosman Bushmaster MPW CO2 Blowback BB Machine Gun is capable of shooting 5.1 grain 4.5mm Steel BB’s at up to 430 fps. When I tested the Crosman Bushmaster MPW CO2 Blowback BB Machine Gun using my Chronograph averaging out 5 shots using a brand new set of CO2 cartridges I averaged 385 fps. Note the temperature in my Indoor Airgun Sea Can Shooting Range was not super warm at about 20-22 degrees Celsius or right around 70 degrees Fahrenheit. I was able to get 405 fps from the Crosman DPMS SBR CO2 Blowback BB M4 but I have a feeling the temperate may have been a little bit warmer for the DPMS SBR Testing which does help to increase the fps.
Moving on to the accuracy portion of this Field Test Shooting Review for the Crosman Bushmaster MPW CO2 Blowback BB Machine Gun, I loaded up the 25 round magazine with the maximum amount t it would hold and then placed 10 semi auto shots on my paper target setup 30 feet downrange. I was using a rested and seated shooting position to help minimize human factor. I was a bit surprised that the Crosman Bushmaster MPW CO2 Blowback BB Machine Gun shot a 2.5 inch semi auto 10 shot group since the Crosman DPMS SBR CO2 Blowback BB M4 was able to get just under 1 inch when I performed the same test.
I then flipped the semi auto selector switch to full auto and dumped the remaining 15 rounds into my paper target in full auto mode and to my surprise the Crosman Bushmaster MPW CO2 Blowback BB Machine Gun actually tightened up it’s grouping a little bit closer to 1.5 inches which is amazing in full auto mode with the airgun rocking around a lot due to the blowback action.
I think it really comes down to which of the Crosman AR type full auto BB rifles you like the look of since both are very capable shooters. Or just get both if you can’t decide :)
In this Field Test Shooting Review Video I test out both the 3.8 Compact and 4.5 Full Size Air Venturi Springfield Armory XDM Blowback CO2 BB Pistols to see how they perform in both velocity and accuracy. I thought it would be interesting to see how the shorter and longer barreled versions compare side by side and if we sill see a difference in power and down range accuracy…
As always I use a brand new 12 gram CO2 along with 5.1 gran zinc coated steel BB’s for my testing and on this day the temperature in the Sea Can Indoor Airgun range was around 24 degrees Celsius or 75 degrees Fahrenheit.
This Review for the Umarex Legends Cowboy Shell Ejecting CO2 BB Rifle is a bit different than most I do since usually I perform a dedicated Table Top and Field Test Reviews for each gun I review here on the Replica Airguns Website. I feel that since the Umarex Legends Cowboy Shell Ejecting CO2 BB Rifle is such a “long gun” that showing it on the table would not work so well , plus it was a super nice day and I wanted to get outside and maybe even shoot a little bit.
I will be performing my usual Field Test Shooting video where I test the Feet Per Second and accuracy at 30 feet so stay posted for that. For now I will leave you with this outdoor “Show and Tell” review.
Specifications:
Type: CO2 BB Rifle. Manufacturer: Umarex Model: Umarex Legends Cowboy Materials: Mainly metal with plastic stock. Weight: 5.95 pounds (2699 grams). Length: 38 inches total length Barrel: 19.25 inch Metal non-rifled smooth bore. Propulsion: Dual 12 gram CO2. Action: Lever Action. Ammunition Type: 4.5mm Steel BB's. Ammunition Capacity: 10. FPS: 410 fps.
Trigger Pull: The trigger pull on the Umarex Legends Cowboy Shell Ejecting CO2 BB Rifle is pretty much a single action only trigger since you will need to work the lever action to not only elect and chamber a shell but to also pre cock the hammer. Once the hammer is cocked and ready the trigger pull is short, light and crips, perfect for accurate shooting.
Accuracy: I have only shot 16 rounds through the Umarex Legends Cowboy Shell Ejecting CO2 BB Rifle during the making of this review video and found the Umarex Legends Cowboy Shell Ejecting CO2 BB Rifle to shoot right on target at 30 feet out. I did notice it shot just slightly high at this range but not a lot and it was dead center windage wise. For longer ranges you can adjust the rear sight to raise the barrel even more. In terms of power it’s hard to say what I was getting, Umarex says it should hit around 410 fps, I felt like it was pretty close to this , maybe a tad bit faster but I will find out for sure when I perform my Field Test Shooting Video Review shortly.
Build Quality: The Umarex Legends Cowboy Shell Ejecting CO2 BB Rifle looks and feels great coming in at nearly 6 pounds and built out of mostly metal with a plastic stock. Don’t be too put out by the plastic stock, it does mimmic the part of wood very well. All the metal parts have a semi-gloss or I would even say matt back finish and so far the paint is wearing pretty good, no noticeable paint coming off that I can see. The action works great with no failure to chamber, eject or shoot rounds.
Realism: The Umarex Legends Cowboy Shell Ejecting CO2 BB Rifle is an awesome example of the classic lever action cowboy rifle. Having the ejecting shells makes it feel like you are shooting the real deal right from the time you start loading up the 10 shells into the pipe magazine, until you work that lever action and pull the trigger. Watching the ejected shells fly through the air is the icing on the cake :) There is not much more you can ask for from a BB firing replica Lever Action Cowboy Rifle!
Pros:
Super realistic replica lever action BB firing Cowboy Rifle.
Fully working lever action, chambers and ejects shells perfectly.
Good weight and feel to it with lots of metal throughout.
Everything works exactly like the real steel version.
Duel CO2 to help get not only more shots before reloading CO2 but also a more consistent FPS from all shots.
Adjustable rear sight for elevation.
Comes with 10 rounds and can also use your Umarex Colt Single Action Army BB shells in it.
Plastic imitation wood stock looks very much like real wood.
Cons:
Stock is not real wood, hopefully Umarex offers a wood upgrade for it at some time.
A bit low in FPS, why not take it right up to 499 fps since the US version has a 600 fps rating.
Took too long for us to get it here in Canada!.
Comments:
The Umarex Legends Cowboy Shell Ejecting CO2 BB Rifle is a perfect example of an Airgun company listening to their customers and bringing to market exactly what we are looking for, kind of like the Single Action Army Revolvers that came out a while back. These old cowboy guns are a blast to shoot from the time you pick up the rifle, insert 10 shells into the magazine, work the lever action, pull that trigger and then repeat 10 times. This is a must have for anyone looking for a super realistic BB rifle, even if you’re not an old west cowboy fan I think you will love shooting the Umarex Legends Cowboy Shell Ejecting CO2 BB Rifle!
My Table Top Video of the Umarex Legends Cowboy Shell Ejecting CO2 BB Rifle:
Watch my Video for all the main differences but in short here they are for those reading this post:
Steel BB version uses CO2 while the Airsoft version uses Green Gas or Propane.
There is no orange tip on the Steel BB version while Airsoft versions come with orange tips installed.
Steel BB versions have 20 round full length magazines for both the 3.8 and 4.5 inch versions, while the Airsoft 3.8 compact comes with the shorter 14 round magazine and the Airsoft 4.5 comes with a longer 25 round magazine.
FPS for the Steel BB versions are 270fps for the 3.8 and 325fps for the 4.5, comparably the Airsoft 3.8 is claimed to have 280fps with the 4.5 version a bit higher at 330fps. (Keep in mind that steel BB’s weigh more at around .33 grams compared to the .20 gram plastic Airsoft BB’s used for testing).
I did notice that on the sliver slide version, my earlier Airsoft 4.5 had more of a parkerized metallic finish while my same Steel BB version I received at a later time had more of brushed stainless look to it. Air Venturi has since informed me that all silver slide version will now have the brushed stainless finish.
Type: BB Rifle. Manufacturer: Crosman. Model: Bushmaster MPW. Materials: Metal & plastic. Weight: 6.5 pounds (4.98 kilograms). Length: 21 inches (Stock all the way in). Propulsion: 12 gram CO2 dual cartridges. Action: Blowback - single action only. Ammunition Type: 4.5mm steel BB's. Ammunition Capacity: 25 rounds. FPS: 430fps. Rate of Fire: 1400 rounds per minute in full auto
Trigger Pull: The trigger pull on the Crosman Bushmaster MPW CO2 Blowback BB Machine Gun is single action only since the charging handle must be cocked first before you can shoot it. The trigger is short and fairly light as you would expect from an AR type trigger action. The bonus with the Crosman Bushmaster MPW CO2 Blowback BB Machine Gun is when you switch it over to full auto mode and just one pull and hold of the trigger will empty the 25 round magazine in just seconds.
Accuracy: So far I have not actually shot the Crosman Bushmaster MPW CO2 Blowback BB Machine Gun but since the internals are exactly the same as the Crosman DPMS SBR CO2 Blowback BB M4 I have already fully review, then I will expect it to performa about the same until I do my Field Test Shooting Review. You shoudl expect about 400 fps in semi auto mode and in terms of accuracy I hope to get a similar 3/4 inch 10 round semi auto grouping from 30 feet away. Full auto will open up the group a bit but not too much, maybe around 2 inches…
Build Quality: The Crosman Bushmaster MPW CO2 Blowback BB Machine Gun is well made all around. Weighing in at 6.5 pounds without any add on accessories it feel solid and well built. There is a lot of metal going on inside and out of this rifle but keep in mind the top and bottom receiver are plastic with metal parts where they need to be like in the internals, pretty much all the working parts are metal, the magazine is full metal, the buffer tub is metal, charging handle, selector switch, magazine release, bolt release, trigger and of course the barrel is metal.
Realism: The Crosman Bushmaster MPW CO2 Blowback BB Machine Gun is about as real as you are going to get in a CO2 Blowback AR/M4 styled Airgun. You can even take it apart and split the top and bottom receivers like the real steal version. The blowback action gives you some recoil but more importantly offers a true single action trigger and of course the full auto ability we all love. Almost all the working parts work like they would on a real M4 other than the forward assist which is moulded into the receiver.
Pros:
Super realistic working M4/AR 4.5mm BB Rifle just like the DPMS SBR but in a different flavor.
Full blowback operation with both semi and full auto shooting, can feel the blowback operation rocking the gun.
Good weight and feel to it.
Almost everything works exactly like the real steel version. (Charging handle, dust cover, bolt release, magazine release, selector switch…)
Duel CO2 full metal drop out magazine that holds the 25 4.5mm steel BB’s.
Adjustable and customizable AR buttstock.
Included red dot sights and ability to add pop-up iron sights.
Lots of rails for mounting additional cool hardware.
Built in Mock Suppressor.
Cons:
Receiver is plastic but well made and does not compromise feel or weight since there is lots of metal throughout this gun.
No iron sights included.
No fore grip included like the DPMS SBR.
Comments:
The Crosman Bushmaster MPW CO2 Blowback BB Machine Gun is really pretty much the same as the Crosman DPMS SBR CO2 Blowback BB Full Auto Rifle with more or less Cosmetic changes. One big advantage over the DPMS SBR is the AR comparable buffer tube which allows you to swap out any AR styled rear stock you choose! You also get an included Red Dot sight since there are no Iron sights. The Crosman Bushmaster MPW CO2 Blowback BB Machine Gun is super customizable with its quad-rail so go ahead and dress yours up with Iron sights, lasers, tactical lights, foregrips or whatever else you can dream up.
My Table Top Video of the Crosman Bushmaster MPW CO2 Blowback BB Machine Gun:
Using .20 gram BB’s I loaded up the Air Venturi Springfield Armory XDM GBB Airsoft Pistol with propane gas and placed several rounds through my Chronograph to see what the feet per second average would be. The last 5 shots I took where actual the fastest averaging 290 fps, a little bit slower than I was expecting but just about right for close quarters Airsoft games.
I then switched over to .32 gram Airsoft BB’s since they tend to be a bit more accurate out at longer ranges. Using a fresh paper target and shooting from a rested and seated position 30 feet away, I took 10 shots with the Air Venturi Springfield Armory XDM GBB Airsoft Pistol. The result was a 10 round grouping of about 2 inches with one straggler just outside the main group. The Air Venturi Springfield Armory XDM GBB Airsoft Pistol did shoot a little bit low at 30 feet but I am sure the hop-up can be adjusted for this. It was well centered left to right which is a good thing since the sights are non-adjustable.
I really like the Air Venturi Springfield Armory XDM GBB Airsoft Pistol, it looks and feels very solid with a nice balance in the hand. The Single Action Only Trigger is short and light making follow up shots quick and responsive. The blowback action is crisp with good simulated recoil. I look forward to trying out the Steel BB version of the Air Venturi Springfield Armory XDM GBB Pistol as soon as I get my hands on one which should be pretty soon. Take your pick, Airsoft or Steel BB, either is a great choice!
