In this Field Test Shooting Video I put the Arcturus AR06 - NY03CB AEG Airsoft Rifles through their paces to find out what the actual Velocity is and how Accurate they both are in both semi and full auto. I use .20 gram Airsoft BB’s for all of the test and I also use an 11.1 volt battery in each Airsoft Rifle. Make sure to checkout my combined Table Top Video for the Arcturus AR06 - NY03CB AEG Airsoft Rifles for more details and info.
Starting off with the velocity or fps for the Arcturus AR06 - NY03CB AEG Airsoft Rifles I place 4-5 rounds through my Chronograph and average the shots out to see what the fps is. Arcturus claims around 380-400 fps but I actually got a bit hotter velocities from both guns with the AR06 averaging 401 fps and the NY03CB averaging 412 fps. Both where supper consistent with their fps, about 2-3fps between the highest and lowest shots.
For my Accuracy Test I shot both the Arcturus AR06 - NY03CB AEG Airsoft Rifles in semi auto first using 10 rounds to find out what the groupings looked like at 30 feet away. I then switch both AEG Airsoft Guns over to full auto and dumped a spring load full form the high-cappa magazine into the paper target setup again at 30 feet down range to see if the groupings opened up much more. The Arcturus AR06 did place all 10 rounds right in about a 1 inch grouping just a tad low and ever so slightly to the left of the bullseye, while the Arcturus NY03CB again got close to the 1 inch grouping but had a few outliers that spread it out to closer to 2 inches, it may hav been me as human factor is for sure a possibility. The Arcturus NY03CB did shoot a little bit closer to the bullseye out of the box but both of these Arcturus AEG Airsoft Rifles have fully adjustable sights. When it came to full auto, both rifles groupings opened up a bit, but not much as the recoil on these AEG rifles is not really a factor.
As I mention in this video, there is a rather large price difference of around $200 extra for the Arcturus AR06 which does get you more metal and some upgrades internally but in the end they both performed about the same, so either choice would be good. I personally like the all metal and look of the Arcturus AR06 but if you want a similar performing AEG and save some money then grab the Arcturus NY03CB.
Type: Blowback CO2 Airsoft Pistol. Manufacturer: Distributed by KJ Works. Model:KP-13. Materials: Metal & Polymer. Weight: 1.7 pounds (770 grams). Barrel: 3.7 inches (95mm) metal non-rifled. Propulsion: CO2 x 1. Action: Semi auto blowback, SOA trigger. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: 24 round drop out full size metal magazine. FPS: Claimed 366+.
Trigger Pull: The trigger pull on the KJ Works KP-13 CO2 Blowback Airsoft Pistol is what you would expect for a true Single Action Only Trigger which is nice and light. There is a bit of take up but you can feel the point near the back where the release kicks in which is extremely predictable with no play in it. Of course you will need to rack the slide in order to place a round in the breach and fire the first shot, after that the blowback action will do all the work for you.
Accuracy: At this point I have not shot the KJWorks KP-13 CO2 Blowback Airsoft Pistol or done my Field Test Performance Video. I would expect the KJWorks KP-13 to perform like the other KJWork Airsoft Pistols I have reviewed in the past, which generally hits the claimed fps. Keep in mind the claimed fps is with the extended barrel and I more than likely will be using the preinstalled shorter non extendable barrel which will have a slower fps for sure. Accuracy should be decent but we will find out when I make my Field Test Shooting video!
Build Quality: The KJWorks line of Airsoft Guns is know for overall good quality so I expect theKJ Works KP-13 CO2 Blowback Airsoft Pistol to be just the same. From my initial first impressions everything looks really good, fit and finish are excellent and as expected you will find metal parts and polymer parts in all the same places you would find them in a real steel modern semi auto pistol.
Realism: The KJ Works KP-13 CO2 Blowback Airsoft Pistol is not an exact replica of a specific semi auto pistol but yo could say it looks a little bit like a Glock ;) You need to be careful when it comes to Glock as they do not like it when companies copy their guns and rightly so. There is enough differences with the KJ Works KP-13 CO2 Blowback Airsoft Pistol so it should not set off any alarms over at Glock. I do like the two tone tan and black color scheme KJ Works went with for the KP-13 but if you like a more traditional look you can always go with the all black version.
Pros:
Metal and Polymer with decent weight and good feel to it.
Heavy Full blowback operation.
Excellent fit and finish as always with KJWorks pistols.
High capacity full size drop out metal magazine that holds the CO2 and 24 rounds.
Well hidden safety incorporated into the serial number under the barrel.
Working trigger safety.
Super easy to see in all conditions fiber optic sight up front.
All working components like a real steel Glock styled pistol.
Comes with extended barrel for higher velocity and easier import into Canada.
Would make a good training weapon if you are use to using Glocks.
Like the two tone finish, but can also get it in all black.
Easily field strip-able.
Cons:
Sights are not adjustable.
Would have liked the addition of white outline on the rear sight.
Slide spring could be slightly heavier.
Comments:
If you’re looking for a pistol that is similar to a Glock for training purposes but is unique in its own way and doesn’t have to be a Glock, then perhaps the KJ Works KP-13 CO2 Blowback Airsoft Pistol may be for you. I like the fact that it has its own style to it and is not just another Glock or Glock Copy. I also like that the KP-13 comes with a CO2 magazine rather than a Green Gas Magazine which will get you a bit higher velocity and more mag fills before requiring to gas up again. I personally like the two tone version but get what you like best, it’s good to have options!
Type: Blowback CO2 Pellet Pistol. Manufacturer: Distributed by Umarex. Model:Glock 17 Gen 5. Materials: Metal & Polymer. Weight: 1.6 pounds (725 grams). Barrel: 4.5 inches metal non-rifled. Propulsion: CO2 x 1. Action: Semi auto blowback, DOA trigger. Ammunition Type: .177 caliber pellets. Ammunition Capacity: 21 round drop out full size metal magazine. FPS: Claimed 370.
Trigger Pull: The trigger pull on the Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol is what I would describe as closer to a DOA (Double Action Only) trigger. The blowback action does retract the internal hammer/striker which does relieve some of the trigger pull but the trigger is also used to rotate the belt magazine which gives the trigger a kind of friction feel especially right at the end of the pull where the rotation occurs. That said it is not a terrible trigger like some other belt fed Airguns but it is certainly nutlike a standard SAO type Glock trigger.
Accuracy: At this point I have not shot the Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol so I can only quote what Umarex is saying in terms of FP2 which is 370. That sounds a bit high for a pellet Airgun but they may be claiming this velocity using a light weight pellets perhaps made out of an alloy rather than lead? I guess we will find out the real world fps using lead pellets and also how accurate it will be when I do my Full Field Test Shooting Video.
Build Quality: The Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol like most of the Umarex Glocks is very well made. I am thinking that Glock to allow Umarex to license Glock Pistols hammy have a quality control as part of this license agreement? Either way the Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol is a solid and well built Airgun all around with quality material and very good fit and finish.
Realism: The Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol in terms of realism as compared to a real steel Glock 19 Gen 5 for sure hits the mark in most categories. It is a bit lighter and you can not field strip it easily, there is also the not so much recessed barrel that is a bit of a giveaway but in terms of most other attributes the Umarex Glock 17 Gen 5 replicates a real Glock… Including the basic looks and feel, the metal slide and polymer frame, the full size drop out metal magazine, the blowback action and most of the working parts including the slide catch release, magazine release and trigger safety.
Pros:
Good weight and feel to it, build quality and fit and finish seem very good.
Really nice looking and full featured replica of the original Glock 17 Gen 5.
Fully Glock licensed via Umarex.
Easy to see white dot sights front and back.
Working trigger safety.
Accessory rail for adding a laser or tactical light.
Full size drop out metal magazine that holds the CO2 and .177 caliber pellets.
Nice high 21 round capacity.
Slide spring feels nice and heavy provide a decent blowback recoil effect.
Safety built into the serial number plate area keeps it well hidden.
Can see through ejection port when magazine is out.
Warning instruction are nice and discreet under trigger guard.
370 claimed fps is good for a CO2 blowback pellet pistol.
Cons:
Barrel is not really all that recessed.
No way to easily field strip it.
Don’t like the clam shell packaging.
Trigger is a bit on the heavy side.
Comments:
I think many of us having been waiting for a pellet shooting version of the Glock from Umarex. I am a bit surprised they went with a belt fed version as belt fed magazines tend to be a bit on the heavy trigger pull side. Yes the Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol has a stronger trigger pull as compared to a 4.5mm BB or 6mm Airsoft version of the same Umarex gun, as most of these Umarex based Glocks utilize a SAO trigger which is more comparable to a real steel Glock. On the plus side the Pellet version should be a bit more accurate, but we will see how this pans out when I do my comprehensive Field Test Shooting Video for the Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol.
Type:Airsoft Rifle. Manufacturer: Acturus. Model: AR06 & NY03CB. Materials: Mostly all Metal. Weight: 5.6/4.9 pounds (2.5/2.2 kilograms). Length: 27.4-30.7/31.7-35 inches (695-780/805-890mm) Barrel Length: 11/14.6 inch (280/370mm) inner 6.02mm tight bore non rifled. Propulsion: AEG (with Deans Connectors). Action: Semi & Full Auto SAO. Ammunition Type: 6mm Airsoft BB's. Ammunition Capacity: Hi Cap/Mid Cap - 550/135 FPS: 380-400fps.
Trigger Pull: The trigger pull on the Arcturus AR06 - NY03CB AEG Airsoft Rifles like other AEG Rifles is not mechanical as they are essentially electrical driven so basically the trigger is an on/off switch that is closest in feel to a single action only trigger since it is light and short. You will notice a slight delay between pressing the trigger and the actual round being fired since the trigger activates a motor which first pulls the air spring back. Once the spring is fully drawn back it releases and compresses the air which then propelled the 6mm Airsoft BB. The higher voltage battery you use like an 11.1 volt will shorten the delay as the motor will spin faster and pull back the spring quicker allowing for less noticeable delay and also a higher rate of full auto fire which in this rifle is very noticeable.
Accuracy: I have not Field Test Reviewed either the Arcturus AR06 - NY03CB AEG Airsoft Rifles or even tried them out yet. I hope to get to my Field Test Shooting Video for both of them later next week, until then we can assume they will shoot similar to most other AEG rifles with tighter bore barrels. I am expecting at least a 2 inch grouping at 30 feet down range in semi auto. In terms of velocity the test paper which they come with claims around 390+fps.
Build Quality: The Arcturus AR06 is a mostly metal with a full metal receiver while the NY03CB has a polymer or plastic receiver which from what I can tell only other components being plastic would be the pistol grips and rear stock. other metal parts on both AR type Airsoft Rifles would be the rail setup, the barrel, the charging handle, the buffer tube, the dust cover, the trigger, the selector switch, the magazine release and bolt release. Fit and finish for both guns is very good.
Realism: The Arcturus AR06 - NY03CB AEG Airsoft Rifles are based on the AR platform with both versions looking the part of a real steel AR. They do come with the removable orange tips installed but they also come with black flash hiders so you can easily switch them out adding to the realism. The metal receiver on the AR06 does give it a bit more weight but even the NY03CB has a decent weight and solid feel to it. Most of the controls work just like a real steel AR including the charging handle, bolt release, selector switch and magazine release.
Pros:
Two versions to meat your budget, both great options.
Quality components throughout both versions. Only real difference is nylon fiber receiver vs metal receiver and slight upgrade motor on AR06 version from Long Type to Long Type 19k torque motor on AR06.
Have been quality control inspected including 5 round recorded fps test with .20 gram Airsoft BB’s.
Both have a functioning bolt catch.
Both come with Quick release two position fully adjustable pop-up sights.
Both come with additional black flash hiders.
Lots of rial mounting options in Picatinny and M-LOK.
6 position adjustable rear stocks.
Easy access to motor for any possible trouble shooting you may need to do.
Additional grip plate option.
Ambidextrous controls and ambidextrous sling mounting points (QD on AR06).
Two magazines come with AR06 (Mid Cap and High Cap).
Cons:
Limited battery options as area is small.
Kind of need a tool to remove rear stock for battery access. (Could change the rear stock)
Mystery accessory baffles me and not mentioned in the manual.
Comments:
Like the AK series of Acturus AEG Airpot Rifles, the Arcturus AR06 - NY03CB AEG are good value for the money with the AR06 offering a slightly higher premium over the lower cost NY03CB. But don’t let the lower price fool you into thinking you are getting a sub-standard product as both versions are built with many of the same components. I personally like the more compact look of the Arcturus AR06 AEG Airsoft Rifle but then again the price of the NY03CB AEG Airsoft Rifle is hard to ignore. Either way you can’t go too wrong so make your pick and enjoy owning one of them.
My Table Top Video of the Acturus AR06 - NY03CB AR AEG Airsoft Rifles:
In this Preview Unboxing Video I Take a look at 4 new Airsoft products from Arcturus all of them being AEG Airsoft Rifles with two based on the AK platform and the other two based on the AR platform. Three of the AEG Airsoft Rifles are mostly metal while I also feature a lower cost version with a Nylon Fiber Polymer receiver. All of these Replica AEG Airsoft Rifles are very good quality but you will get all metal (mostly steel and aluminum) build and a Hi-Cap and Mid-Cap magazine with the higher cost versions.
Trigger Pull: The trigger pull on the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol is single action only which means you will need to rack the slide to not only draw the hammer back but to also chamber the first round. After that the blowback action will do this for you until you are out of ammo and then the slide will lock back. You can also manually draw the hammer back if a round is already chambered. The trigger itself is really nice, it’s light, super short with a crisp light release perfect for fast action shooting.
Accuracy: At this point I have not made my Field Test Shooting portion of my review for the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol so I really don’t know what to expect? KWC claims an fps of 360 using CO2 as its power source and it is a realistic velocity based on previous Velocity tests with similar KWC Airsoft Guns. In terms of accuracy, again I have no idea since I have not reviewed this version of Desert Eagle before. So stay posted till next week when I make the Field Test Shooting Review for it.
Build Quality: Overall the metal and plastic build quality of the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol is good. It is mostly metal with a plastic frame, the real steel version would have an aluminum frame and has a weight closer to 4 pounds total so a bit lighter in terms of weight compared to the powder burning version. The fit and finishes look good.
Realism: The KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol is an excellent Replica Airsoft version of the real steel L6 Desert Eagle including the top and bottom rails and the ported front barrel. It also has full blowback action and you can fully field strip it. I like the addition of the fingered grips which I think adds ot the overall looks and function of this Airsoft Pistol.
Pros:
Lots of metal and good overall weight to it.
Very accurate replica of Desert Eagle L6.
Ergonomic rubberized grips.
Semi and full auto selectable.
Adjustable hop-up.
No orange tip.
CO2 for more power over GBB.
Uses standard KWC CO2 Desert Eagle magazines.
Picatinny rail top and bottom for lots of accessory mounting options.
Great light weight single action only trigger with super short take-up.
Cons:
Frame is plastic so compared to real steel version is much lighter.
Non adjustable sights, also all black so may be hard to see on darker targets.
No trademarks since non-licensed version via KWC direct.
Very large gun with large grips so not suitable for smaller handed shooters.
Comments: Going off just the looks and feel for the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol I can say for sure I do like it compared ot the standard KWC Desert Eagle with its venting up front and its ergonomic rubberized grips. I hope when I perform the Field Test Shooting Video fo fit it it performs well as the price point is good at around $200 Canadian and who doesn't want to have a Desert Eagle in their Replica Airgun collection at the end of the day!
My Table Top Video of the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol:
Type: Pellet Air Pistol. Distributer:KWC. Model: KWC 24/7 TAC NBB Pellet. Materials: Metal and polymer build. Weight: 1.76 pounds (799 grams). Barrel: Rifled steel. Propulsion: CO2 x1. Action: Semi auto non-blowback, double action only. Ammunition Type: .177 caliber pellets. Ammunition Capacity: 16 rounds (2x8). FPS: 360-370.
Trigger Pull: The trigger pull on the KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol is a bit on the medium to heavy side so it’s not going to make for the best action shooter as it is a double action only shooter when compared to a single action only trigger or a single and double action trigger. As with most double action triggers it is a bit longer and slightly heavy but not unusable, just be prepared to get a little bit of a finger workout.
Accuracy: I have not shot the KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol just yet but will be doing so probably next week so stay posted for my Full Field Test Shooting Video for the KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol. I expect it to perform well in terms of accuracy and power since there is no blowback operation to have to compensate for. Having a rifled barrel should also help with accuracy! We will see shortly.
Build Quality: The KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol is built as expected just like all the other KWC Airguns. KWC has been making Airguns for a while not just for themselves but for other companies like Umarex, Gletcher, ASG, Crosman and even Sig Sauer and so quality control and durability have to stand up to these manufacturers standards. You will find metal on this gun where it matter. The slide, the full size drop out metal magazine and of course lots of internal parts. The frame, magazine release, trigger and safety are all plastic. I do like the feel of the rubberized grips for sure! Fit and finish is good overall and the fact that this is a fairly simple Airgun design with no blowback action or even a moving slide, so less moving parts means there is less chance for something to go wrong so it should last a while even with a fair amount of use.
Realism: The KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol shares it’s looks with the Taurus 24/7 but is not an exact replica. The trigger guard is a bit different and so is the placement of the controls and even the slide and frame are not exact but very similar. In terms of size, weight and vernal overall design for sure the KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol looks a lot like a Real Steel Taurus 24/7 at first glance.
Good weight and solid feeling gun. Lots of metal where you need it in the slide, magazine and other internals.
All metal full size drop out magazine holds CO2 and 16 pellets.
Decent looking replica (but not bang on) of a Taurus 24/7.
Not a lot of writing on the gun, very clean looking (Non Ranger version).
Recessed barrel helps with look of realism.
Fiber Optic front and back sights for easy sight acquisition.
Rifled barrel will help with accuracy.
Non-blowback operation with increased fps and CO2 efficiency.
Rail on top of slide and frame for lots of accessory add on options.
Double action trigger is long but not overly heavy so should be OK for action shooting.
Cons:
No blowback, slide is fixed and does not move but can be removed with a tool for internal access and cleaning.
No single action shooting so may not be the most accurate for slowed down shooting.
Sights are not adjustable but you can add an adjustable red dot to it using the rail setup.
Hard to tell when out of ammo, have to listen to the sound or count shots.
Comments:
It is nice to see more full size drop out metal magazine Replica Pellet Pistols coming out in the Airgun market just liek the KWC Makarov PM I just reviewed. Generally speaking most are going to be non-blowback but there are a few blowback options. That said a Non-blowback CO2 Pellet Pistol like the KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol will typically give you a high velocity and more shots per CO2 and can even be a little bit better in the accuracy department since there is virtually no recoil from them. The KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol is a nice little Taurus 24/7 looking Airgun that has a nice modern look and feel to it. Hopefully it performs well for me during my Field Test Shooting Video I will be making soon for it.
My Vimeo Videos for the KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol:
Type: Pellet Pistol. Distributer:Umarex. Model:Stainless Ruger Mark IV. Materials: Metal and polymer build. Weight: 1.56 pounds (708 grams). Barrel: 5.3 inches (135mm). Total Length: 11 inches (279mm). Propulsion: Spring Piston. Action: SAO Break Barrel. Ammunition Type: .177 caliber pellets. Ammunition Capacity: 1 round. FPS: 320.
Trigger Pull: The trigger pull on the Stainless Ruger Mark IV Break Barrel .177 Cal Pellet Pistolis not too bad, I feel it is a around 6-7 pounds or so without measuring. In comparison to a real steel 22LR semi auto SAO trigger pistol, the trigger is much heavier but most of these 22LR pistols of this nature have what I would consider to be near perfect triggers. Over time once you get use to the pressure and release point accuracy with this pistol it is for sure possible.
Accuracy: I have tested out the all black version of this pistol which will perform exactly the same or should I say is expected to perform the same since they are virtually the exact same Pellet Pistol but in different finishes. You can watch my Field Test Shooting Video for the all black version but in case you don’t make it there I will fill you in on the basic results… In terms of velocity I averaged 312 fps using 7 grain lead pellets and got around a 2 inch 7 rounds grouping but expect with a bit more trigger time to get closer to 1 inch.
Build Quality: The Stainless Ruger Mark IV Break Barrel .177 Cal Pellet Pistolis a low cost target plinker that also doubles as a licensed Replica for that coolness factor so you won’t get an all metal super top quality build here. That said metal and plastics are well used and for sure details in the fit and finish have been improved over the Buck Mark URX version where I found the barrel felt a bit sloppy and the trigger was plastic. The Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistol has a much tighter barrel fit when closed and the trigger is now metal! Maybe Umarex watched my video back in the day and took some notes?
Realism: The Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistol most resembles the Mark IV Hunter edition and is pretty much bang on in terms of being a replica other than the tell tail hinge just under the barrel required for a spring piston design, there really is no way to get around this so I’m not going to criticize this minor difference. The real steel version is almost 3 pounds and so the pellet shooting version is a bit under weight so it would have been to have had more metal perhaps in the barrel and lower frame. Again since the pellet shooting version is a springer you will not have any working bolts or slide catches or a built in magazine.
Pros:
It's a decent Ruger Mark IV Replica!
Feels well built overall.
Expect it to have really good accuracy like the Umarex Browning Buck Mark URX since they share similar mechanical design.
Barrel locks into place much better than the Umarex Browning Buck Mark URX did.
Fully adjustable rear sight with fiber optic front sight.
Auto locking safety, just don’t forget to unlock before each shot
Actual metal trigger in this version.
Nice and compact, not too heavy.
Full Ruger licensed via Umarex.
Fairly low price tag.
Cons:
No built in rail for a sight system like the Umarex Browning Buck Mark URX.
Would have liked a metal trigger and maybe a slightly lighter trigger pull to match the real Buck Mark's very light trigger pull.
A bit more metal would have been nice.
Significantly more expensive than the black version which is the same exact gun in a different color.
Comments: The Stainless Ruger Mark IV Break Barrel .177 Cal Pellet Pistol is a decent looking replica and a decent pellet shooting target pistol and if you own the real steel version in 22LR you may just want to get your hands on one of these Break Barrel Replica Pellet shooters. The only real question is do you get the Stainless version with simulated wood grips or the all black version? If you like the look of the stainless version and don’t care about money whatsoever, then pickup that one up since it is a Limited Edition version that will only go up in value over time. If you are on a budget and don’t mind the look of the all black versions or maybe even prefer it then by all means grab one since at the end of the day they will both perform exactly the same.
My Vimeo Table Top Review Videos for the Umarex Stainless Ruger Mark IV Break Barrel .177 Cal Pellet Pistol:
Type:Airsoft pistol. Distributer:Umarex. Model:Smith & Wesson M&P 9L. Materials: Metal and polymer build. Weight: 1.7 pounds (757 grams). Barrel: 4.75 inches (121mm), non-rifled. Total Length: 8.5 inches (215mm). Propulsion: CO2 x1. Action: Semi auto blowback, single action only Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 15 rounds. FPS: 410 Claimed.
Trigger Pull: The trigger pull on the Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol is fairly light weight being a single action only trigger. There is about a quarter inch of take up with an easy release that is not hitchy at all. You will need to rack the slide to load your first Airsoft BB into the breach and engage the action but on the first shot but then the blowback action does this for you until the Airsoft Pistol is out of ammo and the slide locks back.
Accuracy: I have not performed my Field Test Shooting Video for the Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol so stay posted for that video coming out in the next couple of weeks. Umarex has claimed a velocity of around 410 FPS using .20 gram Airsoft BB’s but that does seem a bit quick, well will have to see when I place some shots though my Chronograph! In terms of accuracy I expect it to shoot about the same as most Full Blowback Airsoft Pistols which generally produces a 1.5 to 2 inch 10 shot grouping from 30 feet out using a semi rested shooting position. Again we will find out when I perform my Field Test Shooting Video for the Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol.
Build Quality: The Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol build quality is fairly decent, fit and finish looks good with not too much slide wiggle and the materials used are both metal and plastic or polymer that look to be good quality. I do expect some of the black finishes ot come off on the high spots as these guns are generally electroplated and not too thick with it but this can actually make the gun look more realistic with that slightly worn in look to it.
Realism: The Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol in terms of looking like the real steel version of its counterpart is very close for sure, it would be hard to tell without really taking a close look t it. Everything about this Replica Pistol works for the most part like the real steel version including most of the mechanical parts like the slide catch release, magazine release, take down lever, trigger safety and you can even fully field strip it which gives you easy access to the hopup on the barrel. Of course the full blowback action really seals the deal in terms of making this gun shoot like a real semi auto pistol.
Pros:
Very accurate replica of the S&W M&P 9L.
Fairly accurate weight and feel to it.
Metal and plastic parts where you find them on the real steel version, fit and finish is good.
Working trigger safety and ambidextrous working slide catch release.
Full size dropout metal magazine that holds Airsoft BB's and CO2.
Warning instructions are discreet under the trigger guard.
Recessed barrel and hidden CO2 screw for more realistic look
Fully Smith & Wesson licensed via Umarex.
Rail for add on accessories.
White dot sights for easy target acquisition.
Comes with three sizes of interchangeable grips S/M/L.
Adjustable hopup so you can at least adjust elevation at range.
Comes in a box rather than a clamshell.
Cons:
Has an orange tip but could be painted black or silver to match.
Sight are not adjustable.
15 round magazine has less capacity than some other blowback Airsoft Pistols.
Comments: The Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol is a nice addition to the Smith & Wesson M&P line of Replica Airguns. I’m glad they made it in full blowback but being Airsoft based that is generally the way they lean towards. Hopefully we get to see 4.5mm Steel BB version too in the future! For now we have it in Airsoft and with the longer barrel perhaps it will shoot a bit hotter than most of the other CO2 Blowback Airsoft Pistols, maybe even 410fps like Umarex claims but I will be surprised if it does. I will be happy to see something in the high 300’s to be honest. No matter what, you now have yet another Smith & Wesson option to consider when looking for your ultimate Replica Airgun!
My Vimeo Videos for the Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol
Type:Pellet Rifle. Manufacturer: Umarex Model:HK MP7 .177. Materials: Metal and Polymer. Weight: 4.4 pounds (2kg). Barrel: 11.7 inches (29.7cm). Total Length: 31 inches (78.7cm). Propulsion: Break Barrel Spring Piston. Action: Single Action Single Shot. Ammunition Type: .177 Caliber Pellets. Ammunition Capacity: 1. Max FPS: 490 Claimed.
Trigger Pull: The trigger on the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun is single action only requiring you to break the barrel and compress the internal spring piston before you can shoot it. The actual trigger pull is pretty decent overall. There is very little take-up but the creep is on the longer side but fairly smooth requiring medium pressure. The release is a bit hard at first to predict but nothing some trigger time can’t get you use to.
Accuracy: I have not performed any shooting tests with the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun so far. I hope to make that Video Review next week. I expect the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun to perform well in the accuracy department especially with the included Red Dot Optical Scope installed. I hope the velocity rating from Umarex is based on lead pellets and not hyper velocity light weight pellets but we will find out the story when I perform my Field Test Shooting Video shortly!
Build Quality: The Umarex HK MP7 .177 Cal Break Barrel Pellet Gun is a China made Airgun but looks to be well made. It has lots of metal parts as you would expect from a Spring Piston Rifle which adds a nice weight and feel to it. I did however have an issue with the front plastic mock Suppressor/Compensator as it does not seem to be attached to the metal barrel very well other than being pressure fit which is not going to cut it with all the vibration a spring piston system makes. My first shot loosened the mock Suppressor/Compensator so I will either have to hold it when shooting or find another way to make sure it stays in place.
Realism: The Umarex HK MP7 .177 Cal Break Barrel Pellet Gun is kind of unique in this department as most break barrel rifles are not Replicas, especially the more compact sub machine gun styled ones. Umarex did good job making the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun look like a real HK MP7 for the most part. Of course it is a Spring Piston Rifle at its core so exceptions had to be made to make this work including molded non working parts like the magazine release, sector switch and, bolt/ejection port. That said all in all it is a decent looking replica considering it is a Break Barrel Airgun under the skin.
Pros:
Not many Replica Pellet Rifles on the market, especially in a more compact gun.
Comes with Red Dot sight.
Lots of rails for adding accessories to it.
Full HK Licensed by Umarex.
Collapsible Wire Stock.
Nice high claimed 490 fps.
No need for CO2 so low cost to cooperate.
Not effected by temperature like a CO2 Airgun.
Should have better accuracy than most BB Replica Airguns.
Very solid feel to it, good overall weight and feel.
Cons:
Not going to be an action shooter, have to reload after each shot.
A good overall Replica but not as Realistic or full operation as a BB version would be.
Mock Suppressor/Compensator poorly attached to barrel.
Comments: The Umarex HK MP7 .177 Cal Break Barrel Pellet Gun is an interesting product, on one hadn't it is a Replica Airgun and most people expect a Replica Airgun to have all of the appropriate working parts similar to what would be found on the real steel version. But since this is a Break Barrel Airgun at the core the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun will not function the same as the Real Steel version so as long as you don’t expect it to and appreciate the fact that it should be a nice accurate low cost to operate target rifle then I think you will understand this product and enjoy it for what it is… A Single Shot Pellet Rifle that looks a lot like a HK MP7.
Type: BB Rifle. Manufacturer: Crosman. Model: ST-1. Materials: Metal & plastic. Weight: 6.07 pounds (2.75 kilograms). Total Length: 17.75/33 inches (Pistol/Rifle). Barrel Length: 15.5 inches. Propulsion: 12 gram CO2 dual cartridges. Action: Blowback - single action only. Ammunition Type: 4.5mm steel BB's. Ammunition Capacity: 25 Round/Spring - 300 Round/Hopper. FPS: 480fps. Rate of Fire: 1400 rounds per minute in full auto
Trigger Pull: The trigger pull on the Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun is single action only since the right side charging handle must be cocked first before you can shoot it to engage the action. The trigger is short and fairly light but not overly light. The real fun happens with the Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun when you switch it over to full auto mode and with just one pull and hold of the trigger you empty the 25 round magazine in a mere matter of seconds at 1400 rounds per minute.
Accuracy: I have not actually shot this BB Rifle to date but expect it to get similar results to the other Crosman Full Auto BB Machine guns I have already reviewed. I am expecting a bit more velocity with the longer barrel extension installed and would be happy if I was able to get in the mid 400’s. Accuracy should also be about the same with 1 inch semi auto groups from 30 feet out expending a bit when in full auto.
Build Quality: The Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun is well made all around. Weighing in at 6.07 pounds without any add on accessories other than the included compact Red Dot sight. It feels solid and well built. There is a lot of metal going on inside and out of this rifle but keep in mind the top and bottom receiver are plastic with metal parts where they need to be like in the internals, pretty much all the working parts are metal, the magazine is full metal, the buffer tub is metal, charging handle, selector switch, magazine release, bolt release, trigger and of course the barrel is metal.
Realism: The Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun is not modeled after any real steel gun I know of. It resembles a futuristic weapon you would see in a SciFi Action Movie or Alien First Person Shooter. I was not a fan of it when it was first released by Crosman but after seeing and holding it in person it is growing on me quickly.
Pros:
Very unique, not like your regular Replica Rifles, very futuristic in design.
Drop out magazine doubles as the 300 round hopper and holds CO2 and BB’s.
Comes with Red Dot Sight and lots of rails for mounting what every you want on it.
Can be either a Pistol or Rifle or a PDW by adding or removing the Barrel Extension and Rear Stock.
Barrel Extension actual lengthens the barrel and should increase fps, not just for show!
Tactile comfortable rubber padding in multiple locations.
Semi auto and full Auto selectable.
Expected higher fps of up to 480.
Cons:
Some people may not like the look? Not like your normal modern rifle.
Front rubber grip comes off really easy at least on mine?
Will require barrel extension for full velocity.
Comments:
The Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun is a brave move by Crosman, I was not expecting something like this from them and when I originally saw it I was not sure if it was a good idea or not but again once seeing it in person and actually holing it I feel a lot better about it. It will for sure appeal to those looking for a futuristic Airgun or wanting something that looks like a gun from a video game or SciFi movie. I also like the versatility you have with the Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun being able to configure it how you like either as a Pistol, full on Rifle or PDW style shooter.
My Table Top Video of the Crosman ST-1 CO2 Blowback Full Auto Steel BB Machine Gun:
Sights for guns in general are the same for Airguns as is with real steel guns for the most part and can be mixed and matched with a couple of exceptions. Spring piston rifles for instance are an exception because of the unique vibration the spring makes and how it can damage a standard optical sight, so in this case you’re best to use an optical sight designed for a spring piston Airgun. In most other cases sights can be used on all types of guns.
In this Airgun Sights video I will go over the various types of sights that either come as part of the gun design or can be added afterwards using a rail or mounting system.
Types of Airgun Sights most commonly used.
Iron Sight (Fixed or removable).
Iron Sight (Adjustable).
Iron Sight (White Dot, Fiber Optic).
Come in Post/Notch, Post/Aperture (Peep).
Common on Pistols and Rifles
Laser Sight:
Generally added to a rail or can sometime be integrated into the design of the gun.
Common on both Pistols and Rifles.
Red DotandHolographic:
Generally not magnified.
Most common on Rifles but can be used on Pistols.
Optical Magnified (Telescopic)
Come in a variety of magnifications for different shooting ranges.
Gun Safeties generally are going to be similar for all types of guns, so Safeties used with Airguns are often the same types as used with Real Steel Guns. Some guns will have no Safeties at all while other guns many have multiple Safeties on them. In this informative video I go over six of the more common types of Gun Safeties used in Real Steel Guns and Air Guns.
Here is a list of the more common types of gun Safeties.
I sometimes mention in my review videos that a gun is either Full Blowback or Partial Blowback and some people may not understand exactly what this means and how it effects the Airguns Blowback Action and Performance so I figured it would be best to make a dedicated video talking about the differences and also some of the Pro’s and Con’s of each type of Blowback Action.
In the video I obviously go into a fair amount of detail and show you around each type of Airgun and Magazine as they do differ a fair amount but to summaries for you here in this written form, the main difference is going to be how much the slide moves back and forth. With Full Blowback Airguns the slide will move much longer back and forth on the frame of the Airgun much like a real gun does and the slide Catch/Lock generally locks back further too. With a Partial Blowback Airgun the slide generally has a shorter range of movement back and forth on the frame with the slide locks usually about half of the distance compared to a Full Blowback Airgun.
The magazines are also very different as a Full Blowbacks Airgun generally has a partially exposed BB which is pushed into the barrel by the nozzle with each slide cycle. With a Partial Blowback Airgun the BB is generally not exposed and either the trigger action or simply the CO2 force is required to transfer the BB in the breach of the Airgun.
Another point to mention is that Full Blowback Airguns tend to use more CO2 and have a slightly lower velocity as compared to Partial Blowback Airguns but this is not a rule.
There are many types of magazines used in Airguns and some of this is dependent on the ammunition used.
For instance a stacked type of magazine often used for Steel BB and Airsoft can not be used for Pellets as pellets tend to deform when stacked in such a way since there is no metal casting protecting them from mashing into each other.
So what type of magazines do we generally see in Airguns? The most common Airgun magazines are as follows:
Simple Stick Magazine
Mostly used with Steel BB but also found in some Airsoft Airguns.
Some Pellet Airguns use a type of stick magazine with a rotary magazine on each end.
Used in non-blowback and blowback Airguns.
Can be made from plastic or steel or a combination of both materials.
Full Size Drop Out Magazine
Used with Steel BB and Airsoft guns.
Generally you will find these types magazines hold both the BB’s and CO2.
Used in non-blowback and blowback Airguns.
Commonly used with Airsoft Rifles in mid to high capacity.
Can be made from plastic or steel or a combination of both materials.
Rotary magazine
Used with Steel BB, Airsoft and Pellet Airguns.
Used in non-blowback and blowback Airguns.
Can be made from plastic or steel.
Can often use mixed ammo types as in both 4.5mm Steel BB and .177 caliber pellet.
Belt Fed Magazine
Like rotary magazine belt fed magazine can accommodate Steel BB, Pellet and Airsoft but are most often used with Pellet Airguns.
Usually found in a full size magazine that also holds the CO2.
Used in non-blowback and blowback Airguns.
Can be made from plastic or steel or a combination of both materials.
Internal Magazine
Used with Steel BB, Airsoft.
Can have a hopper built in hat feeds a spring fed magazine.
Usually found in lesser expensive Airguns but not a rule.
In this Video I go through each type of Airgun Magazine and talk about their differences and uses.
I have another Full Auto Fun Video this one focusing on 4.5mm Steel BB Versus 6mm Plastic and which one is better in terms of accuracy and shredding power. I perform this super scientific test by shooting obviously in full auto two comparable Steel BB and Plastic Airsoft Rifles at a paper target setup 20 feet away with a magazine as a backer so I can see what the accuracy is like and how much of the paper magazine gets shredded by each ammo being tested.
I have split this video into three separate videos, in video one I compare two similar AR styled rifles, a CO2 powered Blowback 4.5mm BB Rifle to a Gas Blowback 6mm Airsoft Rifle. In video two I compare two AK type Blowback Rifles to each otters, again a CO2 4.5mm Steel BB along with a Gas 6mm Airsoft.
And lastly in Video three I compare my top picks for each category which include a non-Blowback CO2 4.5mm BB Machine gun to an AEG 6mm Airsoft Rifle.
I have another Full Auto Fun Video this one focusing on 4.5mm Steel BB Versus 6mm Plastic and which one is better in terms of accuracy and shredding power. I perform this super scientific test by shooting obviously in full auto two comparable Steel BB and Plastic Airsoft Rifles at a paper target setup 20 feet away with a magazine as a backer so I can see what the accuracy is like and how much of the paper magazine gets shredded by each ammo being tested.
I have split this video into three separate videos, in video one I compare two similar AR styled rifles, a CO2 powered Blowback 4.5mm BB Rifle to a Gas Blowback 6mm Airsoft Rifle. In video two I compare two AK type Blowback Rifles to each otters, again a CO2 4.5mm Steel BB along with a Gas 6mm Airsoft.
And lastly in Video three I compare my top picks for each category which include a non-Blowback CO2 4.5mm BB Machine gun to an AEG 6mm Airsoft Rifle.
I have another Full Auto Fun Video this one focusing on 4.5mm Steel BB Versus 6mm Plastic and which one is better in terms of accuracy and shredding power. I perform this super scientific test by shooting obviously in full auto two comparable Steel BB and Plastic Airsoft Rifles at a paper target setup 20 feet away with a magazine as a backer so I can see what the accuracy is like and how much of the paper magazine gets shredded by each ammo being tested.
I have split this video into three separate videos, in video one I compare two similar AR styled rifles, a CO2 powered Blowback 4.5mm BB Rifle to a Gas Blowback 6mm Airsoft Rifle. In video two I compare two AK type Blowback Rifles to each otters, again a CO2 4.5mm Steel BB along with a Gas 6mm Airsoft.
And lastly in Video three I compare my top picks for each category which include a non-Blowback CO2 4.5mm BB Machine gun to an AEG 6mm Airsoft Rifle.
For this Video 2 Accuracy Test I shoot all of the above listed Airguns at a paper target setup 30 feet down range using a semi rested shooting position with my hands resting on a sand bag up front and seated on a stool in the back. It’s not perfect but works well enough. I didn’t take a ton of time with each gun since there where 4 to shoot in this Field Test Shooting Video so accuracy may have been a bit better if I took a little more time with each gun.
In Video 2 I test the power and penetration of each Airgun option shooting at a pop can, a soup can and a toilet paper roll so make sure to watch that video if you have not already watched it.
For this Video 1 Power Test I shoot all of the above listed Airguns first at a pop can, then a soup can and then a toilet paper roll. The ides is to test penetration abilities with the pop and soup can and then raw force shooting the toilet paper as it will absorb all the energy from each airgun round and by gauging how much the toilet paper reacts or moves it should tell us which airgun has the most raw power or energy.
In Video 2 I will be testing accuracy using my standard 30 round paper target setup in the Replica Airguns Sea Can so stay posted for that upcoming video shortly…