View fullsize

Type: Paintball Gun.
Manufacturer: Umarex - T4E.
Model: S&W M&P9 M2.0
Materials: Metal & Polymer.
Weight: 763 grams (1.7 pounds).
Barrel: Smooth bore.
Power Source: 1x12 gram CO2.
Action: Semi-Automatic with blowback action.
Ammo Type: .43 Caliber Paintball or Rubber Ball.
Ammo Capacity: 8 Rounds.
FPS: 290.

View fullsize

Trigger Pull: The trigger pull on Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol feels a lot like a double action trigger mainly because when you pull the trigger the inner barrel travels backwards into the magazine which seals off the barrel form the magazine so less CO2 is wasted going it not the magazine and also placing a paintball round in the barrel. This does make the trigger a little bit longer and heavier than a single action trigger. I believe the internal hammer/striker is engaged from the blowback action.

View fullsize

Accuracy: So far I have not had the opportunity to test the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol out so stay posted for my future Field Test Shooting Video where I will see what kind of fps and accuracy we can expect from the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol. You can watch my Field Test Shooting Video for the Umarex Walther PPQ M2 .43 Cal. Paintball Pistol as it is very similar in design..

View fullsize

Build Quality: The build quality of the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol is really very good, metal parts are where you would expect them, the slide, slide catch, barrel, magazine and most internal parts giving the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol a nice near 2 pounds (1.7 pounds) of weight with the magazine in which makes the Paintball version a little heavier than the real steal version (1.54 pounds) but once the real steal version is loaded with a full mag this may even out a bit. The Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol does have a polymer frame but again this is normal with todays modern guns and helps keep the weight down. Fit and finish is also very good!

View fullsize

Realism: The Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol  is a near perfect replica of the real steel S&W M&P9 M2.0 Pistol, from the fully licensed markings to the large .43 caliber diameter barrel. If you placed the Paintball version side by side with the real steel version I doubt you could tell them apart unless you start inspecting it really close up and working the action. You will find that the slide cycle distance is a bit shorter than it would be meaning that when the side catch is engaged the slide does not go as far back as it the real 9mm S&W M&P9 M2.0. Field stripping the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol will requires some tools and pin removal.

Purchase it from: The Canada Replica Airguns Store or the US Replica Airguns Store

View fullsize

Pros:

• Really great weight and solid feeling gun.

• Full Metal slide that locks back on the last shot.

• All metal heavy full size drop out magazine adds some additional weight to the gun.

• Very Accurate S&W M&P9 M2.0 replica, almost indistinguishable from the real still version.

• Everything works pretty much like the real gun so a great training tool.

• Adjustable yellow dot sights.

• Working trigger safety.

• Fit and finish is excellent.

• Magazine spring release really shoots the magazine out.

• Love the .43 caliber barrel opening, adds to realism.

View fullsize

Cons:

• Trigger is a bit long as it shoots like a double action trigger, this is because the inner barrel has to travel back into the magazine before firing.

• Magazine only holds 8 rounds, so you are going to need extra magazines for sure.

• Blowback action is not full blowback, more like a typical half blowback BB gun.

View fullsize

Comments:

The Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol is mechanically very close to the Umarex Walther PPQ M2 .43 Cal. Paintball Pistol in how it functions as a Paintball Pistol so I expect both to shoot very similarly and that’s not a bad thing since the Umarex Walther PPQ M2 .43 Cal. Paintball Pistol performed rather well for me in the Replica Airguns Sea Can Indoor Shooting Range. I like that the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol come with additional back-straps to fit any sized hands and overall I feel it would make a great training tool since the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol as it looks, feels and functions just like a real 9mm S&W M&P9 M2.0.

Buy from: The Canada Replica Airguns Store or the US Replica Airguns Store

View fullsize

I don’t do a lot of paintball gun reviews, they just don’t come across my table all that often so it’s a lot fo fun when I do get the chance to shoot some beefier caliber ammunition in the Replica Airguns Sea Can Indoor Airgun Shooting Range. Of course I use rubber ball ammo rather than standard paintball rounds in order to keep the mess to a minimum.

I have not done my Table Top YouTube Video Review yet for the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun but you can checkout a Preview Video for now. In Summary the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun is a pretty much exactly what the name says. It’s basically a sawn off pistol grip styled double barrel shotgun that uses CO2 and shoots .68 caliber paintballs. You have a selector for shooting either out of the left or right barrel or if you want to can even both at the same time but this really slows down the fps so I would not advise it with the 200 fps version that I was testing with.

View fullsize

Now on to the actual testing of the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun! As alway I like to find out how close to the factory claimed fps I will get. Umarex claims around 200 fps for this version which is around 7.5 Joules of energy, apparently there is a 16 Joules version that shoots closer to 300 fps but we do not carry it at least right now. I put a couple fo rounds through my Umarex T4E HDS Double Barrel CO2 Paintball Shotgun using rubber ball paintballs which will be a little bit heavier than a standard paintballs and my first shot yielded 180 fps, my second shot was slightly higher at 184 fps so pretty close to the claimed 200 fps and that was in not the warmest of environments since the temperature in the Replica Airguns Sea Can Indoor Airgun Shooting Range was only 16 Degrees Celsius (60 Degrees Fahrenheit).

View fullsize

Next up it was time to see how the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun performed shooting at a target setup 30 feet away. Since there are no actual sights on the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun I had to kind eyeball it and as I shot it more and more I was able to get my shots closer to the center of the target. The Umarex T4E HDS Double Barrel CO2 Paintball Shotgun is not a tac driver but at 30 feet out you should be able to hit an 8-10 inch target pretty consistently. I don’t recommend using the double shot option since the same amount of CO2 is applied to both rounds that would normally be applied to one round decreasing the fps by about half making the paintball rounds shoot a lot slower and not really being that effective. This may be an option with the higher 300 fps version of the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun.

So all in all I had a lot of fun shooting the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun, it’s kind of like a big boy Nerf Gun that you can take onto the paintball field if you wanted to. For home defense I think it is a bit underpowered but there may be a little bit of shock factor that could slow someone down or deter them enough to either give you time get away or take shelter somewhere safe. Maybe using the pepper rounds would work OK in this situation? Either way the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun is a really cool and unique CO2 Airgun that is not overly expensive and a welcome addition to any Airgun enthusiasts collection.

• Buy the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun in Canada

• Buy the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun in the US

View fullsize

In this Unboxing Preview video you really can’t get too much different in terms of product types. First up I showcase the Umarex T4E HDS Double Barrel .68 caliber CO2 Paintball Shotgun. I then take a look at the Diana Bandit PCP and Diana Chaser CO2 Bolt Action Match Grade .177 Caliber Pellet Pistols.

The Umarex T4E HDS Double Barrel .68 caliber CO2 Paintball Shotgun is a two shot short barrelled that could come in handy for CQB engagements but it looks to be designed also as a none lethal home defence weapon since you can load a CO2 without piercing it but when in a bind you simply hit the CO2 screw and it pierces the CO2 activating the gun for instant use. I will have to test this one out to see if it really has enough power to stop an intrude, after all you only get two shots so they better count!

View fullsize

And then we have two Diana Match Grade CO2 Bolt Action Pellet Pistols, both has a similar bolt, sights, barrel and trigger setup but with the Diana Bandit you get a wooden grips, an included 10 shot rotary magazine and it’s PCP powered so you will need a compressor or a pump to use it. The Diana Chaser on the other hand is CO2 powered, has a plastic pistol grip and does not include the 10 shot rotary magazine but you can buy it later on if you get bored loading one round at a time into the breach. I expect both of these pistols to be tack drivers!

View fullsize

The Umarex T4E HDS Double Barrel .68 caliber CO2 Paintball Shotgun is available in both our Canada and US Online Replica Airgun Store while Both Diana Pellet Pistols can only be found in our Canada Store.

• Buy the Umarex T4E HDS Double Barrel .68 caliber CO2 Paintball Shotgun in Canada

• Buy the Umarex T4E HDS Double Barrel .68 caliber CO2 Paintball Shotgun in the US

• Buy the Diana Chaser CO2 .177 Caliber Pellet Pistol in Canada

• Buy the Diana Bandit PCP .177 Caliber Pellet Pistol in Canada

View fullsize

If you have not already watched my Table Top Video Review for the Umarex T4E HK 416 Training Marker CO2 Paintball Rifle than make sure to do so if you are interested in more specifications and details.

I don’t often make many Paintball Review Gun Videos let alone Shooting Videos so this one is a bit different than the norm. Lucky for me I have some .43 caliber Rubber Paintballs that I can use in my Indoor Sea Can Shooting Range so as not to make a mess of things. As per usual I like to use a brand new 12 Gram CO2 Cartridge for my testing and for your reference the temperature was right around room temperature or 21 degree Celsius, 69 degrees Fahrenheit.

View fullsize

First up I generally perform my Chronograph test to see what the real world velocity or fps is for the Umarex T4E HK 416 Training Marker CO2 Paintball Rifle. I shot a short string of rubber rounds through my Chronograph and was able to get a 280 fps average with the Umarex T4E HK 416 Training Marker CO2 Paintball Rifle. This is plenty enough power for the intended target down range to feel the paintball effect without causing too much trauma.

With the remaining 10 rounds in my Umarex T4E HK 416 Training Marker CO2 Paintball Rifle magazine, I then setup a brand new paper target 30 feet down range and using a rested and seated shooting position and carefully unloaded the Umarex T4E HK 416 Training Marker CO2 Paintball Rifle into the target. I was a bit surprised to see the rounds spread out a fair amount perhaps as much as 10-12 inches but at least half where in the target rings.

View fullsize

I would not recommend the Umarex T4E HK 416 Training Marker CO2 Paintball Rifle as a long range paintball marker but it would be perfect for close quarters ultra realistic simulations. I would like to give actual .43 caliber paintballs a try outside to see if accuracy would be better, maybe the rubber balls grip the barrel a bit too much causing some random and unexpected spinning to occur? Either way the Umarex T4E HK 416 Training Marker CO2 Paintball Rifle is a really unique and fun Paintball Gun to shoot, maybe not for everyone but if you want the most realistic Paintball Marker then it would be a great option.

Buy in the Canada Replica Airguns Store or the US Replica Airguns Store

View fullsize

Type: Paintball Rifle.
Manufacturer: Umarex - T4E.
Model: H&K 416.
Materials: Metal & Polymer.
Weight: 3016 grams (6.65 pounds).
Barrel: Metal smooth bore.
Power Source: 1x12 gram CO2.
Action: Semi-Automatic with internal working bolt blowback action.
Ammo Type: .43 Caliber Paintball or Rubber Ball.
Ammo Capacity: 14 Rounds.
FPS: 330-460?

Trigger Pull: The trigger pull on Umarex T4E T4E HK 416 Training Marker CO2 Paintball Rifle is pretty typical of what you would find on an AR styled rifle. Since the internal bolt cycles with each shot, the trigger is engaged and the Paintball rifle is ready for the next shot with a very light and short single action trigger pull.

View fullsize

Accuracy: So far I have not had the opportunity to test the Umarex T4E T4E HK 416 Training Marker CO2 Paintball Rifle other than placing a few rounds down range into my ammo trap to see how it shot and felt. Without actually shooting rounds through the Chronograph I don’t really know what the fps velocity is going to be but I can say it felt like it was shooting perhaps even over 400 fps? Out of the box the Umarex T4E T4E HK 416 Training Marker CO2 Paintball Rifle was shooting rather low but you can adjust the rear sight for windage and elevation.

Build Quality: The build quality of the Umarex T4E T4E HK 416 Training Marker CO2 Paintball Rifle is very good since this Paintball gun is made for military and law enforcement training use. You’re going to find high quality metal and polymer where you would normally find them on the real steel version. The bolt carrier is expected to last at least 3000 shots but you do get an extra one included with it.

View fullsize

Realism: The fully licensed Umarex T4E T4E HK 416 Training Marker CO2 Paintball Rifle is about as realistic as you are going to get in a Paintball Rifle. It’s basically made very similar to a GBB Airsoft Rifle of the same type with a working bolt and pretty much all working parts on it. You can even break the Umarex T4E T4E HK 416 Training Marker CO2 Paintball Rifle down into the lower and upper receiver halves. The bolt blowback action is not super strong but this may be a good thing since CO2 usage will be more efficient allowing for higher fps and more shots per CO2.

Purchase it from the Canada Replica Airguns Store or the US Replica Airguns Store

View fullsize

View fullsize

Pros:

• Seem to have decent fps, will see when I do my Field Test?

• Full Size drop out magazine that holds 14 .43 caliber Paintballs and the CO2.

• Removable 4 position adjustable stock.

• Removable and adjustable iron sights.

• Lots of rials for adding accessories.

• Fully licensed H&K 4116 replica via Umarex.

• Blowback does give a bit of recoil feedback and allow for a true single action trigger.

• Very high quality metaled polymer build.

• Used as a training weapon for military and law enforcement.

• Comes with extra bolt carrier.

Cons:

• Very expensive, well over $1000!!

• Comes with blue hardware but can be swapped out (Pistol grip, But stock, Magazine).

• Bolt carrier may wear out at around 3000 rounds.

View fullsize

Comments:

If’ you’re looking for the ultimate in Paintball Rifle realism the Umarex T4E T4E HK 416 Training Marker CO2 Paintball Rifle is going to meet that requirement for sure. It will come at a pretty decent cost but you are going to have a very unique Airgun that not many people will own. And as they say you do get what you pay for which is realism, quality and reliability. I look forward to testing out the Umarex T4E T4E HK 416 Training Marker CO2 Paintball Rifle on the Chronograph using some rubber ball ammo, I may even take it outside for some paintball ammo shooting, we will have to see…

Buy in the Canada Replica Airguns Store or the US Replica Airguns Store

View fullsize

Some more stuff came in and I just had to show it off before moving on with the reviews. I know you're going to like it so here we go again...

View fullsize

First off the super anticipate Umarex Glock 19 CO2 BB Pistol has arrived and is now available in our Canada and US online Replica Airgun Stores so get yours while we still have them, if we still have them? No this version is not a blowback or even working slide version and yes it has the dreaded stick mag! That all said the Umarex Glock 19 CO2 BB Pistol feels really solid and well made and heck it's the first licensed Airgun Glock ever so it's a good start. Umarex has said that more elaborate blowback versions will be coming out down the road. There are full blowback Airsoft version licensed by Umarex but the FPS is too slow right now for us to import them into Canada, hopefully there is a fix for this at some point...

I have been waiting at least three months now for my AW Custom AG-HX2003 Double Stack Tactical 1911 Full Blowback CO2 BB Pistol to show up. Canada Customs got their hands on it and felt it needed to be processed for three months before delivering it to me. at least I did end up getting it without a fight!

View fullsize

AW Custom is primarily an Airsoft gun manufacturer but is moving into the 4.5mm Steel BB market and has a few 4.5mm Steel BB offerings which have interchangeable parts with their Airsoft guns if you need them. I will making a Table Top and Field Test Sooting Video for the AW Custom AG-HX2003 Double Stack Tactical 1911 Full Blowback CO2 BB Pistol, my list is getting pretty huge now but I am excited I have all these new products to review for everyone!

View fullsize

Last on my Update list is a rather pricey one but not something I have ever revised on this channel, It's the Umarex T4E HK416 .43 caliber Paintball M4/AR Rifle made specifically for m military and police training. This gun is super realistic with similar working parts to its real steel counterpart. Check the Umarex T4E HK416 .43 caliber Paintball M4/AR Rifle in our Canada and US Online Stores.

I made a similar video about how to hold your airgun a while back but sometimes they get a bit buried in all the video I make. I feel it's really important how you grip your gun even if it's only an airgun with very little kick or recoil. Proper pistol grip is something you should use no matter what so that you can carry it forward to what ever gun you are shooting.

More kick or recoil means a firmer grip is required to hold the gun so when shooting a powder burner with lots of kick grip becomes even more important.

In this video I go over the proper two handed grip to use when holding a pistol, which hand to hold lose and which had to grip tight, how to overlap your fingers and thumbs.

View fullsize

It was fun to shoot the Umarex Walther PPQ M2 .43 Cal. Paintball Pistol for a change but really it was a lot like shooting one of my BB and Airsoft pistols, except in this case I was shooting .43 caliber rubber balls. I decided to not use paintballs inside my nice new Sea Can Indoor Airguns Shooting Range to keep things clean :)

View fullsize

First, I put three rounds through my Chrony Chronograph to see what the real world FPS would be, keep in mind I was using rubber balls rather than paintballs and the rubber balls are a little bit heavier than paintballs so this could bring the FPS down a bit compared to the lighter paintballs. Using a brand new CO2, the Umarex Walther PPQ M2 .43 Cal. Paintball Pistol average 316 FPS which was high than the claimed 290 FPS!

View fullsize

Moving on to my accuracy testing, as per usual I positioned myself 30 feet back from my paper target and using a seated and rested shooting position I shot a full magazine (8 rounds) of rubber balls on target with the Umarex Walther PPQ M2 .43 Cal. Paintball Pistol. I was not expecting anything close to what I would get with a BB or Airsoft pistol since Paintball guns are not known for super tight groups. I did manage to shoot around a 6 inch group with most of the shots staying within around 3 inches. This is about what I was expecting as paintball guns are not meant for "target practicing", generally you are going to be shooting human sized objects and hoping to get some well placed center mass shots. 3-6 inch accuracy at 30 feet will get the job done for sure. I did find the trigger using rubber balls did have a bit more friction while the inner barrel seated itself into the magazine. When shooting quickly it is much less noticeable.

View fullsize

I know some of you are going to ask about using the Umarex Walther PPQ M2 .43 Cal. Paintball Pistol with rubber balls for non-lethal self defense and the reality is it will not stop a person who is persistent on hurting you. There is simply not enough stoping power here. Will it "sting like a bitch" if you get shot up close with one of these Umarex Walther PPQ M2 .43 Cal. Paintball Pistol? For sure but a well timed punch has more chance of dropping someone than a .43 caliber rubber ball moving at around 300 FPS. You may scare someone off simply by brandishing it but you take the chance of the person calling your bluff. Perhaps 8 rubber balls to the face will change their mind but that's a chance you have to figure out if you want to take or not.

View fullsize

As a paintball pistol, the Umarex Walther PPQ M2 .43 Cal. Paintball Pistol is about the best I have seen in terms of replica paintball guns. It is as good as they come for realism, even better than many BB and Airsoft guns and in terms of performance it did not let me down either.

Buy in the Canada Replica Airguns Store or the US Replica Airguns Store

View fullsize

Type: Paintball Gun.
Manufacturer: Umarex - T4E.
Model: Walther PPQ M2.
Materials: Metal & Polymer.
Weight: 848 grams (1.87 pounds).
Barrel: Smooth bore.
Power Source: 1x12 gram CO2.
Action: Semi-Automatic with blowback action.
Ammo Type: .43 Caliber Paintball or Rubber Ball.
Ammo Capacity: 9 Rounds.
FPS: 290.

View fullsize

Trigger Pull: The trigger pull on Umarex Walther PPQ M2 .43 Cal. Paintball Pistol feels a lot like a double action trigger, internally it may be striker fired so expect a bit of a longer trigger pull with a fairly long reset and a medium strength trigger weight. There is also a working trigger safety which works well.

View fullsize

Accuracy: So far I have not had the opportunity to test the Umarex Walther PPQ M2 .43 Cal. Paintball Pistol out so stay posted for a future Field Test Shooting video where I will see what kind of fps and accuracy we can expect form the Umarex Walther PPQ M2 .43 Cal. Paintball Pistol. So far all I have to go on is what I have seen in some other video reviews I have watched, for the most part the Umarex Walther PPQ M2 .43 Cal. Paintball Pistol performed well.

View fullsize

Build Quality: The build quality of the Umarex Walther PPQ M2 .43 Cal. Paintball Pistol is really very good, metal parts are where you would expect them, the slide, slide catch, barrel, magazine and most internal parts giving the Umarex Walther PPQ M2 .43 Cal. Paintball Pistol a nice near 2 pounds (1.87 pounds) of weight with the magazine in which makes the Paintball version a little heavier than the real still version (1.53 pounds) but once the real steal version is loaded with a full mag this may even out a bit. The Walther PPQ M2 does have a polymer frame but again this is normal with todays modern guns and helps keep the weigth down. Fit and finish is also excellent.

View fullsize

Realism: The Umarex Walther PPQ M2 .43 Cal. Paintball Pistol is a near perfect replica of the real steel Walther PPQ M2, form the fully licensed markings to the large .43 caliber diameter barrel. If you placed the Paintball version side by side with the real steel version I doubt you could tell them apart? You will find that the slide cycle distance is a bit shorter than it shoudl be meaning that when the side catch is engaged the slide does not go as far back as it should. Filed stopping the Walther PPQ M2 .43 Cal. Paintball Pistol may requires some tools.

Purchase it from: The Canada Replica Airguns Store or the US Replica Airguns Store

View fullsize

Pros:

• Really great weight and solid feeling gun.

• Full Metal slide that locks back on the last shot.

• All metal heavy full size drop out magazine adds some additional weigth to the gun.

• Very Accurate Walther PPQ replica, almost indistinguishable from the real still version.

• Everything works pretty much like the real gun so a great training tool.

• Adjustable yellow dot sights.

• Working trigger safety.

• Fit and finish is excellent.

• Magazine spring release really shoots the magazine out.

• Love the .43 caliber barrel opening, adds to realism.

View fullsize

Cons:

• Trigger pull seems a bit long as it shoots like a double action trigger, may be striker fired internally?

• Magazine only holds 9 rounds, so you are going to need extras.

• Blowback action is not full blowback, more like a typical BB airgun.

View fullsize

Comments:

I'm really glad to see another Replica Paintball Pistol available in Canada, especially such a well made and realistic version. The Umarex Walther PPQ M2 .43 Cal. Paintball Pistol looks to be perhaps the best to date .43 caliber Paintball gun on the market and may even prove to be an option for non-lethal personal defense when using rubber balls with it. Not that I would trust my life with it but it sure looks the part and I am sure most people would not want to be on the receiving end of 9 rounds coming at you. As a training tool and Paintball gun the Umarex Walther PPQ M2 .43 Cal. Paintball Pistol offers superb realism for this purpose. I am looking forward to testing mine out shortly :)

Buy in the Canada Replica Airguns Store or the US Replica Airguns Store

One of the most common types of question I get on my Replica Airguns YouTube channel has to be something like… Why is my Airgun not working? Most of the time the amount of info about the problem is limited to something like… “It was working yesterday but now it’s not working anymore” or something like “when I pull the trigger nothing happens”. My personal favorite is… “I took my gun apart and now it doesn’t work!”

I just made a similar video for Blank Guns and as I said in that video, trying to trouble shoot a mechanical or technical problem over the internet is very difficult, this goes for cars, guns, computers or what have you…

In this Why is My CO2 Airgun Not Working video I will however cover some of the more common and obvious problems I have seen relating to why a CO2 Airgun may not be working properly. I really don’t get a lot of questions about Spring Piston or Pump Airguns so I will be focusing on CO2 Airguns in this video. There will be a lot of crossover with CO2 Airsoft guns so this video may be helpful for some of you Airsofters out there

First let’s get the super obvious stuff out of the way! 

• Did you put a new CO2 cartridge in it and is it pierced all the way?

• Did you load BB’s or Pellets into the Airguns magazine and is the magazine in the gun correctly?

• Is the safety off?

• If the gun is a blowback semi auto single action Airgun then did you pull the slide back prior to the first shot?

CO2 Related Problems:

Not all CO2 cartridges are created equal, they often have slightly different shaped nubs on them and some brands will work better than others in different Airguns. If the shape of the CO2 nub does not fit properly into the valve area then it may not pierce or it could pierce but then not allow you to tighten it all the way losing all the CO2 in the process. If the CO2 is coming form the airguns handle to CO2 Valve area then this is an indication that your problem is related to the area where the CO2 enters the airgun.

There is a seal where the CO2 cartridge buts up to the valve, this seal can be damaged or even deformed from usage or even leaving your CO2 in the gun for too long. The outside CO2 Valve seal can also take the shape of a specific CO2 nub so when you use a different brand CO2 the seal may not properly make concat with the new CO2 type you are using, again causing leaking or even the total loss of all your CO2. Watch my YouTube video on “How to Fix Leaking CO2 in an Airgun”.

CO2 Valve Related Problems:

Again, make sure that Outside CO2 Valve Seal is in good condition and any leaking is not being caused by this problem, if you have checked the Out Side Seal and everything is OK with it then perhaps there is a problem with the CO2 valve?

One indication that your CO2 Valve might be the culprit is the total loss of all your CO2 when you try to insert and tighten a new CO2 Cartridge. Usually all the CO2 will exit the barrel, not the handle or valve area. What may be happening is the valve is stuck open or the internal seal is broken or deformed. If this is the case you will have to remove the valve and have a look inside, this is a lot easier on CO2 airguns that have the CO2 valve in the magazine, if the CO2 valve is in the actual Airguns then a lot more disassembly may be required and I would recommend an Airgun technician take care of this for you.

If the gavel is in the magazine then you will have to unscrew it, you may require a special tool for this? Once the valve is out of the magazine  take a look inside and examine the internal seal, also look for any bits of metal shavings as they can disrupt the action of the valve causing leaking. Give the inside of the valve a good clean and then lubricate it with some silence spray. hopefully that fixes your problem!

BB’s getting Stuck in the Blowback Gas Tube:

I have actually made a dedicated video for this problem so I will put a link to it in the description of this video. The main reason people may have this problem is because we all like to rack that slide on our full blowback Airguns, but if you have a fully loaded magazine then each time you reach that slide without shooting the gun, you are inadvertently trying to load another BB into the breach area, the breach is only designed to hold one BB at a time so after a few racks of the slide the newly loaded have no place to go but into the Gas Tube where they can get stuck and cause having to the operation of your Full Blowback CO2 Airgun.

BB’s Rolling Out of the Barrel of Your CO2 Airgun:

This is not actually a fault of the gun but happens because of the way the gun is designed. This situation can happen with certain CO2 Airguns when the gun user pulls the trigger really slowly while the gun is point slightly in a downward position. What is actually happening is the first part of the trigger is made to draw a BB from the magazine into the breach of the gun. If the barrel of the gun does not have a rubber hop-up stopper in it then the BB is free to roll down the barrel and out of the gun. How do you fix this problem? Be more committed to your trigger pull and or shoot at a target that is not so low. Perhaps place your targets slightly higher than the gun so the barrel is not pointing down, especially if you like to take your time with the trigger :)

A Little Maintenance Can Go a Long Way!

Sometimes a good cleans is all you need to do to get things working as they should, again I have already made video Tutorial Showing “How to Clean Airguns and Blank Guns”.

What about stuff like My Airgun is jammed or my trigger is stuck or some random part fell out of my gun?

There is only so much I can cover in this video, most other problems are going to get a bit more complicated to fix and I suggest if your Airgun is not working and the suggestions I have made in this video do not solve your problem, then consider taking your gun into a gun tech.

First off I want to say it’s hard to trouble shoot technical or mechanical problems over the internet regardless of if ithas to do with guns, cars, computers or pretty much anything where unless you are there in person it’s really hard to figure out the problem.

But I will attempt to address some of the more common issues why a blank gun may not be functioning properly.

Why is my Semi Auto Blank Gun Not Cycling or Ejecting Shells?

One very common reason a blank gun may not be cycling the shells properly is because the owner has removed the barrel restrictor plug. People usually do this to make the barrel opening look more realistic but the barrel restrictor is a necessary component to increase the back pressure allowing the slide to cycle fully to the rear position so it can eject and pickup a new shell.

The blanks you are using may not have enough gun powder in them. Some blank guns require banks with more gun powder than others, again this additional internal pressure forces the slide all the way back, if the blank does not have enough gun powder in it then only a partial slide motion happens and so the discharged shell may not eject properly, in this case the user would have to clear the blank gun manually so another shell can then be picked up and loaded into the breach.

If your blank guns is dirty or not lubricated then it may act sluggish again restricting the full movement of the slide which will effect correct operation. Make sure to thoroughly clean and lubricate your blank gun, that may be a quick fix for you!

You may have a faulty extractor? The extractor is like a hook that grabs the discharged shell while the slide is in the reward position pulling or extracting the shell out of the breach. If the extractor is worn or broken then the empty shell will not be ejected from the breach so when a new shell is picked up from the magazine it has nowhere to go and usually you will get a jam-up in the ejection port area.

One final situation that can cause your blank gun to not cycle properly is to strong of a slide spring, some blank guns out of the box just come with a really heavy slide spring, so much so that even blanks with lots of gunpowder in them are still not strong enough to make the slide operate full motion. Your only option here would be to replace the heavy slide spring with a lighter one.

Why Are My Blanks Not Firing?

This is a situation where you pull the trigger and nothing happens. Lets get the obvious causes right out of the way here… Did you put blanks in your gun and are they new blanks? Did you chamber the first round in your semi auto pistol?

So now that that’s out of the way let’s look at some other reasons why your blank gun may not be firing a blank. Perhaps the firing pin is broken? Most blank guns are not made out of carbon steel and even the firing pins can be lesser quality than what you would find in a real gun so blank guns are more prone to breaking than real guns. I have seen broken firing pins in blank guns first hand so make sure to check the firing pin and that it is fully operational.

Try changing up your blanks to another brand? Again blank gun ammunition is not made to the same higher standards that real firearm ammo is made and some primers may require a little more pressure than your gun is providing. Even with real guns an ammo change may help the gun operate better.

Why is the Trigger or Hammer Not Operating Properly?

I have come across blank guns where there are mechanical problems in the trigger and hammer areas, you may be able to address this yourself but I would recommend taking your blank gun to a gunsmith since you will have to take the gun pretty much full apart to fix a problem in the trigger and hammer areas.

Of course make sure your gun is clean and lubricated, this can help a lot with the mechanical areas of your blank gun.

One problem I saw with a few EKOL Special 99’s was specifically with the single action potion of the trigger, when I would pull the hammer back it would not lock back and the hammer would often slip and fire randomly, this is rather dangerous. When I took the gun apart I found that the table top or step that the trigger was supposed to catch on was worn down on the edge so it would simply slip off. I was able to fix this by filing a new edge on the step area. Again this can happen because blank guns are not made out of as high quality metal materials as real guns.

Why does the Flame Come out the Top of My Blank Gun and Not the Front?

If you find that the flame or discharge comes out of the top of your blank gun and not the barrel, this usually does not mean anything is wrong with your blank gun. All it means is you own a top venting blank gun and not a front firing blank gun. In some countries front firing blank guns are not allowed but front venting blank guns are. The same may also be reversed in some countries, for instance here in Canada we can only import front firing blank guns with flare adaptors since our blank guns are imported under the assumption that they are to be used as signaling or flare devices.

Can I Convert my Top Venting Blank Gun into a Front Venting Blank Gun?

I really don't recommend altering a blank gun in any way as it may be a violation of your local laws and it could cause the blank gun to malfunction in a very bad way causing serious injury or even death!

In theory I suppose it may be possible to convert your Top Venting Blank Gun into a Front Venting Blank Gun but again you would need to allow for just the right amount of back pressure so a wide open barrel would not work unless it was a revolver. You can not simply remove the red plug and bingo you have a front firing blank gun because in most cases the barrel will be completely plugged in the frontal region. Not only would you need to drill out the plugged portion of the barrel but you would also have to somehow fill in the top venting area and again makes sure to allow for just enough back pressure to cycle the slide back and forth.

Hopefully this has helped some of you with blank gun issues. If you’re looking for a blank gun make sure to come down to www.ReplicaAirguns.ca and www.ReplicaAirguns.us and have a look in our blank gun area of our online stores.

I already made several review videos for both Gletcher NGT (4.5mm Steel BB) and the Gletcher NGT R (.177 Cal Pellet) Revolvers, including table top and shooting videos. So make sure to check those videos out for more information on both versions of Gletcher NGT and NGT R Revolvers.

I did however miss some noteworthy details that I wanted to cover in this video. Firstly, the real steal Nagant M1895 Revolver this Gletcher NGT is styled after has a very unique gas-sealing system that the Airgun version does not replicate or really require but it is worth mentioning.

Here is some more info on how the original Nagant M1895 Revolver Gas Seal System works:

(From Wikipedia) The M1895 by contrast, has a mechanism which, as the hammer is cocked, first turns the cylinder and then moves it forward, closing the gap between the cylinder and the barrel. The cartridge, also unique, plays an important part in sealing the gun to the escape of propellant gases. The bullet is deeply seated, entirely within the cartridge case, and the case is slightly reduced in diameter at its mouth. The barrel features a short conical section at its rear; this accepts the mouth of the cartridge, completing the gas seal. By sealing the gap, the velocity of the bullet is increased by 15 to 45 m/s (50 to 150 ft/s.) This feature also eliminates the possibility of injury through the dangerous expansion of gases from the cylinder behind the barrel, which are easily capable of severing a finger if the user holds the gun incorrectly (with a finger positioned in front of the cylinder during fire) - a noted safety-issue in conventional revolvers.

Moving on to some of the features incorporated into the Gletcher NGT NGT-R CO2 BB and Pellet Revolver that I did not point in any of my previous videos. There is an extractor rod that can be used to extract a shell, this is not really necessary on the airgun version since the shells do not expand and tighten on the cylinder as they would n the real steal Nagant M1895 Revolver built is nice that we can replicate this feature with the Airgun version. You can also remove the cylinder completely from both the BB and Pellet shooting Gletcher NGT NGT-R CO2 Revolvers. The cylinder is actually very heavy and adds a lot of weight to this compact 7 shot Revolver.

It is always nice when an Airgun is built in such a way that it replicates the real steal version as closely as possible and the Gletcher NGT NGT-R CO2 BB and Pellet Revolvers do this nearly perfectly.

Buy Gletcher NGT Revolvers in Canada

Buy Gletcher NGT Revolvers in the US

I get asked on a daily bases form many of my Vimeo Viewers about how and if there is a way to get rid of the White lettering on Airguns, Typically people are wanting to remove the intrusive Warning instructions from Airguns like the Cybergun Tanfoglio Witness 1911, the Cybergun/Swiss Arms GSG 92/P92 and many other CO2 Replica Airguns that have lettering or branding that you may want to get rid of.

In this Instructional Tutorial Video I show you how can at least tone down the white lettering and even completely remove it on some Airguns without damaging the Airguns finish underneath the white lettering. You will have to use some patience and perhaps repeat this method a few times but the end result is worth the effort.

The magical product I use to remove the white lettering on many popular Airguns is a product from Birchwood Casey called the Presto Gun Blue Pen. This product is actually designed to touch up real steel gun in areas where the blueing has worn off, lucky for us the Birchwood Casey Presto Gun Blue Pen also works well to remove the ugly white lettering from Airguns.

I have often been asked which of the Shells for the Shell Loading Revolvers work in which Shell Loading Revolvers? After all many of them look a lot alike so can you mix and match Shells for the various types of Shell Loading Revolvers?

In this Vimeo Instructional Video I test out a bunch of Shells to see which ones actually will work or not work in several of the most popular Shell Loading Revolvers.

Some of the Shell Loading Revovers Tested in this Instructional Video are:

• Dan Wesson Classic Revolver (BB, Airsoft, Pellet)

• Dan Wesson 715 Revolver (BB, Airsoft, Pellet)

• Colt Single Action Army Peacemaker (BB, Airsoft, Pellet)

• Gletcher NGT and NGT-R (BB and Pellet)

• Webley Mark VI (BB)

• KWC 357 / Umarex 357 (BB, Airsoft)

• G&G G731 (Airsoft) 

Make sure to watch my Table Top Review for all the Features and Specifications for the ANT Advanced Novelty Tech FIRE CO2 HPA Conversion Kit.

In this Field Test Shooting Video Review I compare using a standard 12 gram CO2 versus my ANT Advanced Novelty Tech FIRE CO2 HPA Conversion Kit with HPA (High Pressure Air).

To make this as comparable a test as possible I used two KWC/Gletcher Makarov Full Blowback Pistols each with their own separate magazine, again one with a 12 gram  CO2 and one using the ANT system.

HPA or High Presure Air is not effected by cold weather which makes this setup ideal for shooting in cold situations since fps is not effected at all. As CO2 requires heat to expand, the colder the outside temperature the less amount of expansion you get from the CO2 whihc results in less power, this is really noticeable on your follow-up magazines as the CO2, magazine and even the gun will have started to cool down from the CO2 exposure.

The ANT Advanced Novelty Tech FIRE CO2 HPA Conversion Kit even when using large 20 ounce CO2 tanks will help with the cool down effect since the large CO2 tanks will take much longer to cool down and even freeze up as compared to the smaller 12 gram CO2 which can get frosty even after the first magazine.

I did notice in this Field Test Shooting Review that the CO2 did pretty good as it was my first magazine and the temperature was not all that cold out. I can say the HPA System was shooting much harder, after making this video I popped off another couple magazine with each gun shooting out to at least 100 feet and the ANT FIRE HPA setup was really throwing the 4.5mm Steel BB's out there quickly. As expected the 12 gram CO2 mags really started to trail off especially on the third magazine of shots.

All in all, the ANT Advanced Novelty Tech FIRE CO2 HPA Conversion Kit will not only bring your cost per shot down significantly but it allows you to keep shooting with no down time waiting for your gun to warm back up and the ability to use HPA (High Pressure Air) means you will get even more fps performance out of your air guns but also much more consistent shot performance all day long!

I reviewed the Original ANT (Advanced Novelty Tech) CO2 HPA Conversion Kit last year and did both a Table Top Review and Field Test Shooting Review, so make sure to check out my video reviews for the Original ANT Advanced Novelty Tech CO2 HPA Conversion Kit.

Well ANT (Advanced Novelty Tech) made an update model that supports a bunch more guns, that's a good thing of course. This new model is called the "FIRE" and it supports the following guns. I did find however that ANT list that the Gletcher NGT and Webley Mark VI Revolvers where supported by the FIRE but my findings indicated the CO2 screw on both these guns had a smaller diameter so they where not compatible. Other than that small discrepancy most of the other guns on their list should work just fine.

What exactly is the ANT Advanced Novelty Tech FIRE CO2 HPA Conversion Kit?

The Advanced Novelty Tech FIRE CO2/HPA Conversion Kit is a remote line adapter for Airsoft, BB, and pellet guns. Compatible with over 60 guns, it is easy to install and converts a compatible gun for use with a Paintball remote line and CO2 or HPA tank. Eliminating the need for disposable CO2 cartridges, while still being interchangeable with disposable CO2 cartridges, it delivers a longer, more powerful, and more consistent shooting experience between refills.

So what is the ANT Advanced Novelty Tech FIRE CO2 HPA Conversion Kit going to do for you?

• Eliminate the need for the more expensive disposable 12 gram CO2 cartridges.

• Use interchangeably with disposable 12 gram CO2 cartridges.

• Use in conjunction with a Paintball remote line with standard quick disconnect fittings and a CO2 or HPA tank. (recommended use up to 1000 psi)

• Shoot thousands of rounds before needing to refill your CO2.

• Fits compatible Airsoft, BB, and pellet gun CO2 pistols.

• Easy drop-in installation.

• Overall cost savings.

• More consistent FPS especially when shooting fast or in full auto.

• Longer play time :)

I will be doing a Field Test Shooting Review for the ANT Advanced Novelty Tech FIRE CO2 HPA Conversion Kit but based on my experience with the Original ANT CO2 HPA Conversion Kit I expect it to work as advertised.

As most my Vimeo Subscribers and Viewers will already know, I have been struggling with my Chrony Shooting Chronograph for a while now. I know some of it is to do with the bad lighting under my deck but over time my Chrony F-1 Shooting Chronograph has become less and less reliable to the point now that I simply don't get any usable feedback from it. If I'm lucky on a good day I might get one FPS reading out of ten shots which is nothing I can use.

So recently I went out and purchased a new Chrony Shooting Chronograph, I actually upgraded a little bit and got the higher end Chrony Beta Shooting Chronograph version which has more options than my older F-1 Chrony like:

• Selector switch to change from FPS (feet per second) to MPS (meter per second).

• Delivers Measurements and Statistics such as - High, Low and Average Velocities, Extreme Spread and Standard Deviation.

• Retrieve individual Shot Velocities and Statistics.

• Has temporary working memory.

• Has 60 shot permanent memory (divided into 6 numbered strings of up to 10 shots each, with one set of Statistics for each string).

• Delete individual shots (with automatic adjustment of Statistics).

• Delete the content of a whole string or all data from memory.

• Can be switched off, taken home & switched on again for reviewing and information retrieval.

• Memory will stay even without battery.

• Moves instantly from string to string, interrupts shooting on any string without memory loss, returns to any string to continue where you left off.

• Change string size.

• Stereo Jack for optional Printer or Remote Control.

• Forget Button - To clear individual strings instantly.

• Upgrade to 1000 shot memory.

• Upgrade to Gamma or Gamma Master Chrony.

Probably a lot more features than I actually need or will even use but the price for the Chrony Beta Shooting Chronograph over the Chrony F-1 Shooting Chronograph I have been using was only about $30 more so I figured why not go for it.

In this review video I mainly show you around my new Chrony Beta Shooting Chronograph and don't really talk too much about features since it is all new to me and I have not played around with my new Beta Chrony much so far.

I do plan to do some Field Testing with my the Chrony Beta Shooting Chronograph and shoot some of the Airguns that I was not overly successful getting readings for like my new Sig Sauer Pellet Pistols and Sig Sauer MPX Rifle along with my ISSC M22 BB CO2 Pistol. So stay tuned for that upcoming Field Test video.

I am showcasing here on the Replica Airguns website and over on the Replica Airguns YouTube channel a series of videos I will be making for the purpose of selling some guns out of my personal collection. I simply have no more room for the new guns and in some cases I either have duplicate guns or very similar versions so there is no need to have both. Some guns I am less attached to and as I already stated I need to make room for some of the new stuff I will be reviewing and or buying for myself.

In this second Mike's Personal Guns For Sale video I am offering three rifles, two of which will require a Canada PAL Firearms License since one is a 22LR rimfire rifle and the other is a high powered .22 caliber break barrel pellet rifle. The last item up for bid is an AK-47 styled .68 caliber paintball rifle.

Make sure to watch my above YouTube video to see these three rifles I am selling and instructions on how you can take part in the sale and purchase of them. By the way I am only selling to Canadian residents since shipping cross borders is a little sketchy.

Here is a list of the these three rifles I am selling from my personal gun collection:

ISSC MK22 22LR (FN SCAR) Rifle - $625 PAL Required

Benjamin Sheridan Super Streak .22 Caliber Break Barrel Rifle $250 PAL Required

Tacamo T68 AK-47 .68 Cal. Paintball Rifle $275

When I say Airguns, I am referring to pretty much all BB, Airsoft, Pellet, Paintball and even Blank guns for most of the topics listed here.

Do’s:

1. Treat your Airgun just like you would a real gun. If something goes wrong, perhaps the outcome will not be as severe but do you really want to take a trip down to your local emergency ward to get a BB or Pellet removed?

2. Always assume your airgun is loaded, for some reason it always seems those empty guns are the ones that do the most damage.

3. Be discrete, If it looks like a gun other people will think it is a gun so don’t flash your airguns around in public. Keep it in a case when transporting and shoot it in an area that will not alarm other people.

4. Always wear eye protection when shooting your Airgun. Do you really want to shoot your eye out? No Joke!

5. Be aware of your surroundings like windows, hard objects that could make your ammo bounce back at you. Make sure you are shooting your Airgun in a safe direction at all times, know your target and beyond.

6. Use Airguns to teach others and learn how to safely and effectively shoot a gun. Airguns can be less intimidating then a real gun (Not so loud and very little recoil) and make for great start out and transitions guns.

7. Use Airguns to get more inexpensive trigger time and become a more experienced shooter. Airguns cosy only pennies per round to shoot and can be shot in way more areas than a real gun can, practice makes perfect so get shooting!

8. Use Airguns in areas where real guns may not be allowed or safe to use. Again, Airguns can be shot in all kinds of places, in your back yard or even in a properly setup indoor home range.

9. Use Airguns with adequate power for safe and humane pest control where real guns may be prohibited.Airguns are quiet and less likely for the bullet to travel long ranges which makes them ideal for close range pest control in areas where real guns are too loud and to powerful.

Don’ts:

1. Do not assume because it is an airgun it is not dangerous or simply a toy. Many Deaths have been caused by Airguns along with a lot of pain and suffering so treat your Airgun with respect. It is not a toy or you would find them in the toy department at your local store along with yo-yos and stuffed animals.

2. Do not point or shoot at people unless of course you are using an Airsoft gun in an Airsoft field or facility. Yes Airsoft guns are meant to shoot at each other (with appropriate attire like eye protection and full body clothing), but steel BB and Pellet can cause serious injury especially at close range and on direct skin contact.

3. Do not leave your Airgun loaded, you never know who is going to come across it and accidentally discharge it. Remember, a loaded gun is a dangerous gun in the wrong hands. You may know better than to assume the gun is undulated but children and even adults without any gun training will most definitely handle the airgun without consideration of the danger it poses.

4. Do not use an Airgun for self protection. See my related video. Simply put, Airguns are not practical for self defense because they rarely have enough Stopping Power. The ones that do have enough power need to be pre-charged and in most cases are only single shot meaning if you miss or don’t get the job done no the first shot then you are done.

5. Do not use an underpowered Airgun for pest control. See related video. Using a low powered BB pistol for pest control is cruel, you will only injure the animal making it suffer unnecessarily. Use a high powered pellet rifle to get the job done.

6. Do not take your gun apart, in most cases this will void the warranty and the reality is that airguns rarely need to be cleaned since no dirty gun powder is used. lead pellet rifles may require occasional barrel cleaning to keep the rifled barrel free of debris.

7. Do not over oil your Airgun, a little goes a long way and too much oil will just attracted dirt, use the right airgun oil and just enough to keep part functioning smoothly.

8. Do not over pump an Airgun. Over pumping an Airgun can cause damage to valves and seals and in a worse case situation a rupture the air pressure reservoir or even cause the airgun to explode!

With the popularity of the KWC - Cybergun 1911 Blowback CO2 Pistols and how super realistic they are in so many ways, it is no surprise that people often ask me if they can replace the original grips with grips made for a real 1911.

The short answer is yes you can! You will have to be prepared to remove just a little bit of material from the backside of both grips near the bottom of the handle where there is an area that has been flared out to accommodate the CO2. Not really a big deal, you can use a Dremel for the quick and easy approach or even some sand paper if you don't mind taking a little more time.

In this Vimeo Video I demonstrate using grips that fit a real 1911 and show you just exactly where you will need modify them to fit on the KWC and Cybergun CO2 Blowback 1911 pistol series.

Buy the KWC Blowback CO2 1911 BB Pistol in Canada