View fullsize

This was an unusual Field Test Review for me to do as I really don’t test out Bows or Crossbows all that much and I don’t have the best backstop setup for doing such reviews. So I spent some time making a backstop that was capable of stopping these just over 6 inch almost 10 gram or 150 grain bolts. It required some layers of foam and cardboard along with a blanket behind just in case, and even with this setup the bolts managed to lodge themselves right up to the Fletching (feather part of the arrow). Also make sure to watch my Table Top Video Review for the Bear X Desire XL Crossbow to see it up nice and close and get all the specifications and features.

I kind of wanted to change up this review just a bit and so I recorded my Chronograph Velocity at the same time as I did my Target or Accuracy Test to simplify things. I used 5 bolts in all and got what I felt was a good result using the Bear X Desire XL Crossbow.

In terns of velocity Bear X claims that the Bear X Desire XL Crossbow will shoot around 175 fps. I was able to get consistent 190+ fps readings using the 147 grain 6.5 inch aluminum bolts with my lowest fps being 192 and the highest being 194 so super consistent. This gave an overall Foot Pound energy of 12.4 foot pounds! This is enough for small pests for sure, it really comes down to accuracy at this point as you will want to get either a head or shoulder area shot for a humane kill.

View fullsize

I did do a pre test to make sure I was on target and duding this test I was able to get about a 5 inch 5 shot grouping. During my recored Accuracy Test this did open up a bit as one arrow went high and to the right so if I leave that arrow out of the test I did manage to get another 5 inch grouping with three of the arrows all within 1.5 inches of each otter. I figure with high quality arrows and some practice time using the Bear X Desire XL Crossbow, you should be able to use it for small pest control at least at closer in ranges.

All in all the Bear X Desire XL Crossbow surprised me with how powerful it really was and with the accuracy using standard default bolts. This is for sure not a toy and you would never want to accidentally shoot this at someone as it could cause a very serious injury or even death and I mean that since these arrow would for sure pierce several inches into the body. So if you’re looking for something with a bit more raw power than your standard non-regulated Airgun, then check out the Bear X Desire XL Crossbow over in both our Canada and US Online Replica Airguns Stores.

• Buy the Bear X Desire XL Crossbow in Canada

• Buy the Bear X Desire XL Crossbow in the US

View fullsize

Type: Compact Crossbow.
Manufacturer: Bear X.
Model: Desire XL.
Materials: Metal & plastic.
Weight: 2.3 pounds (1 kilograms).
Length: 20-22 inches.
Propulsion: Bow.
Action: Single action trigger.
Ammunition Type: Aluminum bolts (Comes with 3).
Ammunition Capacity: 1.
FPS: 175fps.
Draw: 60 pounds

View fullsize

Trigger Pull: The trigger pull on the Bear X Desire XL Crossbow is medium to heavy, it is a single action only trigger as you need ot cock the bow in order for the trigger to be engaged. The safety is also engaged when you cock the bow requiring you to take the Bear X Desire XL Crossbow off safe before shooting as an added layer of safety.

View fullsize

Accuracy: I have not made my Field Test Shooting Video for the Bear X Desire XL Crossbow and so I have not sea what to expect for it. I have watched a few videos of other people reviewing it and it looks to perform fairly well but until I get a few bolts in a target downrange I can not say for certain the accuracy of the Bear X Desire XL Crossbow. I will have to figure out some sort of a usable back stop in order to make this Field Test Shooting Video but have some ideas already on material to use as my back stop. FPS is claimed ot be around 175 and I will be doing my best to Chronograph the Bear X Desire XL Crossbow so we can confirm that rating for ourselves…

View fullsize

Build Quality: The Bear X Desire XL Crossbow is actually made pretty decently, yes it is mostly plastic and light weight but feels sturdy enough to hold, the only real metal I can confirm is the cocking rail, mostly everything else other than the nuts and bolts that hold it together are some sort of plastic, the bow itself may be a composite material but I am not sure what exactly it is?

View fullsize

Realism: The Bear X Desire XL Crossbow is not a Replica as is what I usually review here on the channel. But I think their is a crossover in terms of interest for a product like this with people that are also interested in airguns. I know I like the Bear X Desire XL Crossbow and can see a place for it in my collection even if it’s not a replica product.

View fullsize

Pros:

• Fairly inexpensive.

• Super light weight.

• Can shoot in a variety of situations.

• Easy to draw the bow.

• Safety is automatically engaged.

• Picatinny rail already has iron fully adjustable rear sight but can mount a red dot if you like.

• Fiber optic front sight.

• 3 bolts included.

• 175 fps (not sure of the ft/lbs)?

• Comes with fore grip.

• 3 portion adjustable rear but stock.

View fullsize

Cons:

• Will need a good backstop or will lose or damage a lots of bolts.

• Takes a little bit of time to set it up but not too hard if you follow the instructions.

View fullsize

Comments:

The Bear X Desire XL Crossbow is an interesting product that once purchased and if you manage to not lose the bolts will cost virtually nothing to shoot since you can reuse the bolts all day long given you shoot them on target and that target does not damage the bolts. It may not offer the rapid fire action shooting of a replica semi auto CO2 Pistol but still challenges the shooter in terms of getting the best possible accuracy out of it and at the end of the day trigger time is trigger time! If you are looking for something a bit different than your CO2 Air Gun then maybe the Bear X Desire XL Crossbow will fill that requirement.

• Buy the Bear X Desire XL Crossbow in Canada

• Buy the Bear X Desire XL Crossbow in the US

In this Preview Unboxing Vimeo Video I take a look at five very different products! A Spring Piston .177 Caliber Pellet Pistol, an Airsoft GBB Pistol, a Compact Crossbow, a full auto CO2 Blowback BB Pistol and a PPC .22 Caliber Pellet Rifle.

View fullsize

First up is the Umarex Ruger Mark IV Spring Piston Pellet Pistol which is a single shot replica pellet pistol that shoots .177 caliber pellets at up to 320 fps using a spring piston break barrel system. The Umarex Ruger Mark IV Spring Piston Pellet Pistol is a target plinker with fully adjustable fiber optic sights and should be a lot of fun to shoot!

View fullsize

Next I take a look at a Gas Blowback Airsoft Pistol from Action Army that closely resembles the Ruger Mark IV pistol with perhaps a more compact look. The Action Army AAP-01 GBB Airsoft Pistol is full blowback a full size drop out magazine and fiber optic sights. It also come with a threaded barrel and barrel extension for adding a longer barrel and much suppressor.

View fullsize

Next on my list of new items is the Bear X Desire XL Crossbow which is a 2.2 pound compact bolt shooting crossbow that sports a rail system with included adjustable iron sights that also allow for a red dot if you want to really customize it. The Bear X Desire XL Crossbow has a 60 pound draw and shoots arrows/bolts at up to 175 fps.

View fullsize

Another AR BB Rifle/Pistol from Crosman is the Crosman A4-P Full Auto CO2 BB Pistol which is essentially a pistol version of the AR Platform. If you like the Crosman DPMS SBR, R1, PDW then you will probably also like the Crosman AP-4. Like the others it uses dual CO2’s and shoots 4.5mm Steel BB;s in semi or full auto at 1400 rounds per minute until the 25 round magazine is empty.

View fullsize

Last included in this preview video is the Air Venturi Avenger Regulated PCP Pellet Rifle. I’m a bit uncertain about this one as I am pretty sure it is the non detuned PAL version that requires a firearms license here in Canada as it shoots at full velocity (.22 caliber pellet at 950 fps). If that’s the case then it will not be available in our Canada Replica Airguns Store but may be available in the US Replica Airguns Store. If it is the detuned version or a detuned version becomes available in Canada then I imagine we will at some point have it in the Canada replica Airguns Store. That said the Air Venturi Avenger Regulated PCP Pellet Rifle uses compressed air and shoots either .177. .22 or .25 caliber pellets using a latch system and rotary magazine.

After about 4 years or so of not getting sick at all, I was almost starting to think I was impervious to viruses and colds and flues and then it finally happened… I got the Rona.

Now I am not 100% sure if it is the Rona since I have not been tested yet but all signs indicate it’s probably Omicron. I have ordered some antibody tests that I expect to come in shortly, I will be checking my blood for Covid-19 Antibodies once I know my body has had enough time to make them after getting sick this time.

In this video I talk about my symptoms and how I felt start to finish getting the Rona. I can say at least for me it was not big deal, the soar throat was probably the worst of it for me.

View fullsize

Wow, an accessory review, not many of these :) Today I take a look at the Amomax Airsoft Airgun Holster product line since at some point you may want to put your gun in a holster or practice drawing your gun from a holster?

The good news is we just got in a decent amount of product for our Amomax Airsoft Airgun Holsters. Here is a bit of info about Amomax but of course make sure to watch the video as I take a good look at a few of the versions we sell in our Canada and US online Replica Airguns Stores.

View fullsize

Amomax holsters are compatible with 4 different carrying platforms :paddle (standard), belt clip, MOLLE, and drop leg platforms. All the carrying platforms can be replaced by only one screw. Users can carry them in daily use, outdoor sports, normal shooting training and competition. Holster will stay firmly on a belt, leg and MOLLE system even in fast moving situations with a quick release Retention System button that keeps the gun locked in place until you are ready to draw. Holster body and carrying platform are connected with a tooth gear that allows for 360 degrees of rotation. User can easily adjust the carrying position to fit their needs.

View fullsize

Amomax Holsters are currently available in the following versions:

• Glock 17/22/31

• 1911 (Fits most brands 1911’s)

• USP

• Sig P320

• Single and double Universal Magazine

• Buy Amomax Airsoft Airgun Holsters in Canada

• Buy Amomax Airsoft Airgun Holsters in the US

View fullsize

I will say right off the bat this Field Test Shooting Video for the Air Venturi 3000 PSI Aluminum HPA Tank with Stock and Adapter did not go as well as I would have wanted it to! The HPA tank itself worked really well but I believe the adapter was faulty as it was destroying the seals on my tank and not regulating very well.

I still wanted to publish this video regardless as not all reviews go as planned, some fail horribly but I would rather be honest and transparent about it rather than have you believe every product is a perfect.

There will always be problems even with really great products there can be defects. I plan to get a new adaptor and try this Field Test Review Video again but for now you can have some fun watching me at least have some success using the Air Venturi 3000 PSI Aluminum HPA Tank with Stock on my Rap4 Rap5 MP5.

You can also watch my Table Top Review Video for more details and info on this product!

• Buy the Air Venturi 3000 PSI Aluminum HPA Tank with Stock and Adapter in our Canada Store

View fullsize

Type: Airgun Accessory.
Manufacturer: Distributed by Air Venturi.
Model: Air Venturi 3000 PSI with Stock & Adapter Aluminum Tank.
Materials: Aluminum.
PSI: 3000.
Capacity: 13 CU.
Output PSI: 1100.
Diameter: 2 inches.
Length: 10 inches.
Features: Two ASTM burst disks, integrated pressure gauge.
Accessories included: Buttstock, CO2 Adapter.

In this Table Top Review Video I go over the features and benefits of the Air Venturi 3000 PSI with Stock & Adapter Aluminum Tank system, what to expect and some of the Pros and Cons for it.

I will also be following up my Table Top video with a Field Test Shooting Video to see what possible advantages and disadvantages the Air Venturi 3000 PSI with Stock & Adapter Aluminum Tank has in a real world test of its performance, hopefully all advantages!

View fullsize

Pros:

• Compact and is the perfect size to use as a rear buttstock for various 88 Gram and or HPA rifles.

• Smaller tank means if you are using a foot pump it won’t take all day to fill up :)

• Comes with adapter so can be used with regular HPA and 88 Gram CO2 systems.

• Regulated to 1100 psi so should perform better in terms of max velocity and consistency compared to CO2 which is around max 800-900 psi with velocity being effected by cool down.

• Not effected by colder temperatures compared to CO2.

• Once you have this tank the cost is virtually nothing to shoot compared to expensive 88 Gram CO2 cartages. You just need to buy your pellets or BB’s.

Cons:

• Still takes a while to pump up using a foot pump system.

• Higher initial cost ($195) than simply buying 88 gram CO2 cartages when you need them.

• Will need access to a pump or compressor to use it.

• Doesn’t look as good as the supplied buttstock at least with the Sig Sauer MCX and MPX.

View fullsize

Comments:

I guess the question is who is this for? If you are a casual shooter that perhaps owns the Sig MPX or MCX or even another 88 Gram CO2 Air Rifle that the Air Venturi 3000 PSI with Stock & Adapter Aluminum Tank would work with then this may be a bit expensive especially if you don’t have a way to pressurizer the tank at home. On the other hand if you already have a foot pump or air compressor or easy access to one and maybe you have other HPA or CO2 based airguns this tank will work with then it’s kind a no brainer to get it. Maybe you juts want a system that gives you maximum and consistent velocity no matter how cold it is outside. All good reasons to get one in my books.

• Buy the in Air Venturi 3000 PSI with Stock & Adapter Aluminum Tank Canada

In this Update Preview Unboxing Video I take a look at 5 products that came across my table and that I have not reviewed so far on the Replica Airguns YouTube channel.

View fullsize

First I show off an HPA tank from Air Venturi that works perfectly for the Sig Sauer MPX and MCX Pellet Rifles allowing for more consistent fps and I would image a higher overall fps? We will find out when I test it out in the replica Airguns Indoor Sea Can Airgun Range.

• 13 Oz Aluminum

• 10 Inches Long

• 2 Inches Diameter

• Integrated Pressure Gauge

• Includes Buttstock

• CO2 Adaptor Included

• 3000 PSI Fill

• 1100 PSI Regulated

View fullsize

Next I take a look at the KJWorks M9A1 GBB Airsoft Pistol, I hover revived the CO2 version before but this version comes with the Gas magazine rather than the CO2 mag for those that prefer gas operated Blowback Airsoft Pistols. Because of the slightly lower FPS the Gas version comes with a barrel extension to make it Canada import friendly.

• 6mm Airsoft BB’s

• Green Gas / Propane

• 370 fps

• 25 Round Magazine

• 2 Pounds

View fullsize

Probably one of the most interesting product I look at in this video at least for me is the EMG JW3 Combat Master GBB Airsoft Pistol. This Airsoft pistol is mainly aluminum with some polymer based off of the 2011 STI and was featured in the 2019 John Wick 3 Film. I’m really looking forward to testing this one out in the Sea Can Replica Airguns Airgun Range!

• 6mm Airsoft BB’s

• Green Gas / Propane

• 9.4 Inches

• 366 fps

• 28 Round Magazine

• 2.4 Pounds

View fullsize

Moving along to another Air Pistol I finally get my hands on the Crosman P1 which is really just a KWC PT92 4.5mm Blowback CO2 BB Pistol but with Crosman Branding and an included laser. Since I have never shot a PT92 BB Pistol with a laser I will probably make a Field Test Shooting Video to see how well it performs.

• 4.5 mm Steel BB’s

• CO2 x 1

• 4.2 Inch Barrel

• 330 fps

• 19 Round Magazine

• 2.4 Pounds

• Comes with Laser Sight

View fullsize

Last up I take a look at the ASG TAC-6 which is pretty much the exact same ASG TAC-4.5 CO2 Air Rifle I tested a while back but in this case the 6 refers to it being a 6mm Airsoft Rifle rather than a 4.5mm Steel BB Riffle. I am not sure I will do a full Table Top Video since these guns are virtually identical but just in different Ammo types but I hope to get outside and see how well it performs shooting at a bit more distance than the 30 foot indoor range I usually test my Airgun in.

• 6mm Airsoft BB’s

• CO2 x 1

• 36 Inches

• 440 fps

• 15 Round Magazine

• 3.5 Pounds

View fullsize

As with most of the new tech I purchase or acquire that I will be using in my Videos for either my GetFitOver40 or ReplicaAirguns YouTube channels, I generally like to do some sort of a practical review for the item. In this case I take a look at the Synco G1 (A2) Wireless Microphone Set which is a pair of wireless transmitters that pair with a single dedicated receiver allowing me to quickly and easily capture good quality audio for my Videos.

For the past couple of years my go to microphone setup for my video was to use a generic lapel mic connected to my Samsung Galaxy Smartphone recording into an audio program. I would then send the audio file via dropbox to my computer where I would then line up the audio file with the video file in my video editing software to get a much higher quality and more clear voice recording versus what the camera mic would be able to capture.

This system has been working fairly well for me but required a somewhat cumbersome lapel cable and of course my bulky Smartphone in my pocket at all times but did allow me to be as far away from the camera as I wanted without any interference or loss of audio clarity.

View fullsize

After playing around with the Synco G1 (A2) Wireless Microphone System I have determined I will most likely simply be clipping the transmitter onto my shirt without the lavaliere mic plugged in and transmitting the audio into either my Samsung Smartphone or my iPad where I can then again dropbox the audio file to wherever I plan on editing the video.

This video was kind of a test to see how everything sounded in terms of the lapel mic versus the built in mic. What settings to use and how distance effected the audio signal and quality. Unfortunately the lapel mic was a bit close to my voice causing some distortion to occur but you can still hear what I am saying no problem. In the future I would place the lapel mic a bit further away from my voice lower down on my shirt or simply use the built in mic as it was not as sensitive to this distortion and seemed to handle louder volume much better than the lapel mic.

View fullsize

Here are some of the specifications for those that like that sort of info :)

Transmitter (TX )

• Wireless Transmission - Digital 2.4GHz

• RF Frequency Band - 2400-2483.5MHz

• Working Distance - 164ft/50m (LOS area) 98ft/30m (NLOS area)

• Latency - 12.5ms

• Mounting - Pocket Clip

• Audio Input - 1/8" / 3.5 mm TRS Mic Input

• Audio Input Level - 1V (0dBV)

• RF Output Power - ＜10mW

• Power Requirement - 3.3V-4.7V

• Battery Type - Built-in Lithium Battery

• Battery Charging Time - 1.5h

• Battery Life - 5h

• Dimensions - 52X42X16mm

• Material - Plastic

• Weight - 35g

Receiver (RX)

• Wireless Transmission - Digital 2.4GHz

• RF Frequency Band - 2400-2483.5MHz

• Approximate RF Sensitivity - -81dBm

• Working Distance - 164ft/50m (LOS area) 98ft/30m (NLOS area)

• Latency - 12.5ms

• Mounting - Pocket Clip

• Number of Audio Channels - 2

• Audio Output - 1/8” / 3.5 mm TRS Mic Output - 1/8“ / 3.5 mm TRS Headphone Output

• Gain - 0-4 Level (0 to 8dB)

• Audio Output Level - Line Out: 1V, Monitoring: 25-30mW

• Power Requirement - 3.3V-4.7V

• Battery Type - Built-in Lithium Battery, 400mAh

• Battery Charging Time - 1.5h

• Battery Life - 5h

• Dimensions - 52X42X16mm

• Material - Plastic

• Weight - 35g

Microphone

• Form Factor - Built-in/External Mic

• Sound Field - Mono

• Polar Pattern - Omnidirectional

• Frequency Response - 50Hz-20KHz

• Sensitivity - -40dB (±3 dB, re 1V/Pa at 1KHz)

• Max. Input SPL - 135dB SPL (at 1KHz)

I made a video a little bit ago talking about how Canada’s new Bill C-21 will affect pretty every gun owner in Canada including even airgun owners of BB, Pellet Airsoft and even Paintball Guns. Make sure to watch that video first called Bill C-21 Canada is Going After Your Red Ryder BB Gun.

This video is all about how you can get involved in making some waves by signing two online petitions along with contacting your local Member of Parliament and letting them know your disapproval of Bill C-21 and all that it imposes on law abiding Canadian gun owners.

Probably the most important online petition to sign would be the House of Commons Petition E-3201 Bill C-21 so make sure to sign that one!

The other online e-petition we need to sign is the change.org petition.

And lastly but also super important is to send an email to your local member of Parliament again let them know your disapproval of Bill C-21. I have included a link to the web[age where you can locate your local MP and below that is a template of what you could include in your email to them.

https://petitions.ourcommons.ca/en/Petition/Sign/e-3201

Dear (MP),

I am a constituent in your riding. I am writing to you to voice my concerns over the new provisions that were announced under the proposed Bill C-21, and how this will impact myself, my community and many other Canadians.

"Criminal Code 1 (1) The definition replica firearm in subsection 84(1) of the Criminal Code is replaced by the following:

replica firearm means any device that is designed or intended to exactly resemble, or to resemble with near precision, a firearm that is designed or adapted to discharge a shot, bullet or other projectile at a muzzle velocity exceeding 152.4 m per second and at a muzzle energy exceeding 5.7 Joules, and that itself is not a firearm, but does not include any such device that is designed or intended to exactly resemble, or to resemble with near precision, an antique firearm; (réplique)

(2) Section 84 of the Act is amended by adding the following after subsection (3.1): Certain firearms deemed to be prohibited devices

(3.2) For the purposes of sections 99 to 101, 103 to 107 and 117.03, a firearm is deemed to be a prohibited device if

(a) it is proved that the firearm is not designed or adapted to discharge a shot, bullet or other projectile at a muzzle velocity exceeding 152.4 m per second or at a muzzle energy exceeding 5.7 Joules; and (b) the firearm is designed or intended to exactly resemble, or to resemble with near precision, a firearm, other than an antique firearm, that is designed or adapted to discharge a shot, bullet or other projectile at a muzzle velocity exceeding 152.4 m per second and at a muzzle energy exceeding 5.7 Joules."

Make sure to also sign ePetition e-3201 to put a stop to Bill C-21:

https://petitions.ourcommons.ca/en/Petition/Sign/e-3201

View fullsize

In this YouTube Video I test out my new Insta360 One R with the 1 Inch Mod, comparing it to my Sony RX 100 IV to see how they compare against each other.

It’s not really a fair comparison since my Sony RX 100 IV is now 5 or 6 years old which is a long time for a digital camera but it has been really good to me and provided some really great quality video over the years. Compare that to the Insta360 One R that is about a year on the market now and you would think the clear winner would be the Insta360 One R.

On it’s own the Insta360 One R with the standard 4k lens would perform well against the Sony RX 100 IV but the Sony RX 100 IV has a 1 inch sensor allowing it to get the most out of each pixel and since I primarily shoot in 1080p 60 frames per second I need to get as much out of each pixel as I can.

View fullsize

One really great feature about the Insta360 One R is that it is modular so I can swap the 4k module out for a 5.7 k 360 module or even a 1 inch 5.3k module allowing both the Insta360 One R and the Sony RX 100 IV to have that large 1 inch sensor keeping the comparison more inline with each other.

Some things to not that will make a big difference in quality and limitations for this video is that the Insta360 One R 1 Inch Mod was shot using 4k 60 fps while the Sony RX 100 IV was shot using 1080p 60fps. The Insta360 One R 1 Inch Mod has a fixed focus while the Sony RX 100 IV has a variable focus.

Anyway I will let you be the judge and decide which camera you like the look of the video for at least in this shooting situation.

View fullsize

This is by far not a full Review of the Insta360 One R Camera but rather more of my take on the Insta360 One R Camera and what it can do for me and how I plan on using it in by Replica Airguns and Get Fit Over 40 YouTube channels.

View fullsize

I talk about how the Insta360 One R Camera compares to a GoPro type camera and how it can also be much more than a typical action camera because of its ability to morph from one camera to a completely different type of camera because of its modular form factor. Not to mention possible future new hardware lenses and even main modules that could increase the ability of this camera even further.

View fullsize

In this video I show some sample videos I shot using the Insta360 One R Camera with the 4K 60 fps Mod and its 5.3K 30 fps 360 Mod Lenses.

View fullsize

Here are some of the basic Specifications for the Insta360 One R Camera:

Aperture

4K: F2.8

360: F2.0

35mm Equivalent Focal Length

4K: 16.4mm

360: 7.2mm

Photo Resolution

4K: 4000 x 3000 (4:3), 4000 x 2250 (16:9)

360: 6080 x 3040 (2:1)

Video Resolution

4K: 4000x3000@24/25/30fps, 3840x2160@24/25/30/60fps, 2720x1530@24/25/30/60/100fps, 1920x1080@24/25/30/60/120/200fps,

360: 5760x2880@30fps, 5760x2880@24fps, 5760x2880@25fps, 3840x1920@50fps, 3840x1920@30fps, 3008x1504@100fps

Photo Format

4K: jpg, RAW (dng) (RAW files require software on PC/Mac to export.)

360: insp (can be exported via App or Studio), RAW (dng) (RAW files require software on PC/Mac to stitch)

Video Format

4K: insv (can be exported via App or Studio), mp4 (enable in-camera basic stabilization), * The .insv video format has been changed to .mp4 in firmware 1.2.16 and later

360: insv(can be exported via App or Studio), LOG and HDR videos

Video Coding

4K: H.264 / H.265

360: H.264 / H.265

Video Modes

4K: Standard video, HDR video, Timelapse mode, TimeShift mode, Basic stabilization mode (in-camera stabilization), Pro stabilization mode (export with Insta360 app/Studio or supported plugins to apply FlowState stabilization)

360:Standard video, HDR video, Timelapse mode, Bullet Time video

Weight

4K: 121g

360: 130.5g

Dimensions (W x H x D)

4K: 72mm x 48mm x 32.4mm

360: 72mm x 48mm x 43mm

Run Time

4K: 4K@60fps - 70 minutes

360: 5.7K @ 30fps - 70 minutes

Video Bitrate

100Mbps

Gyroscope

6-axis Gyroscope

Compatible Devices

Recommended devices： iOS: A11 or above iOS iPhone SE, iPhone 11/11 Pro/11 Pro Max, iPhone XS/XS Max, iPhone XR, iPhone X, iPhone 8/8 Plus Android: Kirin 980 or above (Huawei Mate20, P30 and above) Qualcomm Snapdragon 845 (Samsung Galaxy S9, Xiaomi Mi 8 and above) Exynos 9810 or above (Samsung S9, S9+, Note9 and above) * Devices that do not meet the above requirements can still use the app to control ONE R, however, some operations with high processing performance requirements such as AI supported functions and video playback, may be sub-optimal.

Photo Modes

Standard photos, HDR photos, Burst, Interval photos, Night Shot, PureShot

Live-streaming

Coming Soon

360 live-streaming, FreeCapture Live (user controls visual perspective)

EV

±4EV

Exposure Modes

Photo Shoot Auto, Manual(Shutter 1/8000s-120s, ISO 100-3200), Shutter Priority(1/8000s-1s), ISO Priority(100-3200) Video Shoot Auto, Manual(Shutter 1/8000 - 1/30, ISO 100-3200)

WB

Auto, 2700K, 4000K, 5000K, 6500K

Bluetooth

BLE4.0

Wi-Fi

5G (Standard range of approximately 20 meters)

USB

Type-C

Micro SD Card

UHS-I V30 speed class, exFAT(FAT64) format SD cards with a max storage of 1T are recommended.

Battery Capacity

1190mAh

Charging Method

Type-C

Charging Time

65mins

Use Environment

-4° F to 104° F (-20℃ to 40℃)

There is not much to really say here, it’s all about watching this one as I basically shoot stuff with the Air-Ordnance SMG 22 Full Auto Pellet Rifle and figure out how many 100 round belts I can get out of a fully charged 3000 PS 48 CU PCP Tank. So make sure to watch this one for sure!

If you haven’t already watched my Features and Specifications Video make sure to take a look to learn more about the Air-Ordnance SMG 22 Full Auto Pellet Rifle. I also made a Part 1 Field Test for the Air-Ordnance SMG 22 Full Auto Pellet Rifle where I put some shots through my Chronograph and also test out the semi auto accuracy at a paper target setup 30 feet down range.

• Buy the Air-Ordnance SMG 22 Full Auto Pellet Rifle in Canada

• Buy the Air-Ordnance SMG 22 Full Auto Pellet Rifle in the US

View fullsize

There have been lots of requests for me to get to the Field Test Shooting Video for the Air-Ordnance SMG 22 Full Auto Pellet Rifle and I know I have been a it late getting this one out there. To be honest I was not looking forward to pumping up the rather large PCP tank and loading up all the 100 round magazines but it had to be done and so here we are…

In this Part 1 of my Air-Ordnance SMG 22 Full Auto Pellet Rifle Field Test Review I perform my usual Sea Can Indoor Shooting Test and place some rounds through my Chronograph to see what the actual FPS is. I also shoot a 10 round group at a paper target 30 feet down range to see what kind of accuracy we can expect from the Air-Ordnance SMG 22 Full Auto Pellet Rifle. By the way in Part 2 I take my Air-Ordnance SMG 22 Full Auto Pellet Rifle outside to have some fun with it and blast away in full auto so make sure to watch that video coming out very soon…

View fullsize

The Air-Ordnance SMG 22 Full Auto Pellet Rifle with a full PCP tank pressurized right up to the max 3000 psi and using 15.43 grain lead pellets was able to get an average fps of 422 which worked out to 6.1 foot pounds of energy or about 8.3 Joules. By the way I was able to get through 3 full 100 round magazines with a fully charged 48 CU Tank which is impressive. Shots did slow down a bit at the end but the gun was able to cycle fully.

In terms of accuracy my Air-Ordnance SMG 22 Full Auto Pellet Rifle was not the most accurate performer I have tested but considering it is a full auto Airgun and not so much made for total accuracy, the 3 inch 10 shot grouping I did get was good enough for me! Of course I was shooting in semi auto mode during this test which is pretty easy to do, no selector switch to worry about, just don’t hold the trigger down and you get semi auto shooting from the Air-Ordnance SMG 22 Full Auto Pellet Rifle, hold it down and you get full auto, and the tighter you hold the trigger down the faster the air machine-gun rate of fire operates.

So far so good, no miss-feeds or any problems with my Air-Ordnance SMG 22 Full Auto Pellet Rifle. now to take it outside and let loose on some clay pigeons, pop cans and a metal target.

• Buy the Air-Ordnance SMG 22 Full Auto Pellet Rifle in Canada

• Buy the Air-Ordnance SMG 22 Full Auto Pellet Rifle in the US

View fullsize

Type: Pellet Pistol
Manufacturer: Diana.
Model: Bandit
Materials: Wood and Metal, some plastic.
Weight: 2.2 pounds (1000 grams).
Total Length: 20.1 inches (51 cm)
Barrel: 9.5 inches (24 cm), metal rifled.
Propulsion: PCP.
Action: Bolt.
Ammunition Type: .177 & .22 Caliber pellets.
Ammunition Capacity: Single shot to 9 & 7 round magazines..
FPS: 725 (.177) - 630 (.22). Need to test for Canada import version

View fullsize

Trigger Pull: The trigger pull on Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol is single action only meaning in order to cock the internal hammer/striker, you need to cycle the bolt back and forth allowing for a short and light trigger action. It does come with a rotary multi-round magazine that allows for the cycling of the bolt to automatically advance a pellet allowing for much quicker followup shots.

View fullsize

Accuracy: At this point I have not personally tested the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol in terms of actual power and accuracy but I expect the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol to perform well since in fact this is a target pistol with fairly high claimed fps. In the next few weeks I plan on making my Field Test Shooting Video so stay posted for the results from that video for confirmation of the performance.

View fullsize

Build Quality: The Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol is made in China which might make you wonder about the overall quality of this target pistol but after taking a good look around and working all the mechanical parts I ma very impressed with the overall quality and chosen material that went into the production of the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol. You will finds metal where you need it as in the barrel, bolt and trigger. The pistol grip are made of wood but you will find some portions of the sights are plastic but it would have been nice if they where all metal.

View fullsize

Realism: Realism isn’t really a concern with the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol since it is not a Replica Airguns but in terms of looking like a gun it serves that purpose, no mistaken that so no waving it around in public or things may not turn out so good for you…

View fullsize

Pros:

• Inexpensive fairly high quality full featured target pistol for the price.

• Expect good accuracy!

• Metal construction where it needs to be (Bolt, barrel, trigger).

• Rifled barrel.

• Fully adjustable sights.

• Adjustable and light single action trigger.

• Dove tail on bolt for adding optical sight.

• Nice wood pistol grip.

• Good for small pest control because of fairly high fps and expected good accuracy for shot placement ability.

• Overall the gun feels really high quality for the price.

• Even comes with a nice soft shell case.

• Available in both .22 and .177 caliber pellet versions.

View fullsize

Cons:

• Grips may be a bit too wide for smaller handed shooters.

• Allen key does not fight the trigger adjustment.

• Made in China.

• Will need a pump or way to pressurize.

View fullsize

Comments:

For the price I don’t think you will find anything out there in terms of a PCP target pellet pistols with as many features as the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol. At least in the lower cost price point Diana is offering it at. For that reason it is not going to be the absolute best all around PCP pellet firing target pistol you can get but I am sure bang for your buck you will be happy with this one. Everything about the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol feels good quality, I would expect to pay at least double the price for something similar for sure. I have a feeling keeping the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol in stock is going to be a challenge for us so if you see it in stock don’t take too long making up your mind or you may be in for a bit of a wait.

My Vimeo Table Top Review for the Diana Bandit PCP .177 Caliber Bolt Action Pellet Pistol:

• Buy the Diana Bandit PCP Bolt Action Pellet Pistol

Without the cool cameras there would be no cool Airgun videos and so when a company reached out to me and says… Hey, would you like to try out one of our new 4K Action cameras? I say sure! I can always use another high quality 4K camera for even more angles and who knows what else…

In this unboxing video I take a look at the SJCAM SJ10 Pro Action Camera to see what’s in the box obviously, what it looks like and what my first impressions of the SJCAM SJ10 Pro Action Camera are. I have to say the build quality is a lot better than I thought it was going to be, I’m pretty sure the main body is made out of metal and the crips looking lcd screen pretty much takes up the entire back of the camera. The camera is a lot smaller than I was expecting too which is a good thing since the more compact a camera is, the more likely I will be taking it along with me and using it.

Until I get the chance to play around with the SJCAM SJ10 Pro Action Camera fully and see what the quality and functionality are like, here are some of the specifications and details:

• Sensor Brand: Sony IMX377.

• Sensor Type: 7-Layer Glass with 2 aspherical glass lenses.

• Video Resolutions: Up to 4K60fps without GYRO up to 4K30fps with Supersmooth GYRO Stabilization, Slow-motion 2,4,8x.

• Photo Resolutions: 12MP (4000×3000 4:3) 10M (3648×2736 4:3) 8M 16:9 (3840×2160 16:9) 8M 4:3 (3264×2448 4:3) 5M (2595×1944 4:3) 3M (2048×1536 4:3) 2MHD (1920X1080 16:9.

• Video Format: MP4 (H.264 / H.265 HVEC).

• Wifi: 2.4 Ghz 802.11 a/b/g/n.

• GYRO Stabilization: Inner Six-Axis Gyroscope.

• Digital Zoom: 8x.

• Battery Capacity: 1300 mAh Detachable Battery.

• Battery Duration (Approx.): 140 Minutes at 1080P 95 Minutes at 4K60fps (Front screen and Wifi off).

• Microphone (Audio In): Dual Stereo Microphones.

• Back Screen: 2.33" UHD IPS SuperSensitive Touch Screen with SJCAM UI.

• Storage supported: Up to 128GB micro SD high quality 10 class and higher memory cards.

View fullsize

Type: Archery.
Manufacturer: Umarex.
Model: AirJavelin & AirSaber.
Materials: Metal & polymer construction.
Weight: 3.9 pounds / 6.3 pounds no scope.
Foot Pounds Energy: 34 ft/lbs / 124 ft/lbs.
Total Length: 34 inches / 41 inches.
Propulsion: 88 gram CO2 x1 / PCP 3625 PSI, 250 cc.
Action: Bolt single action.
Ammunition Type: Carbon fiber 190 grain / 350 grain arrows (Field tip can be swapped over to broad-head)
Ammunition Capacity: 1 Arrow.
Max FPS: 300 / 450.

View fullsize

Trigger Pull: The trigger pull on both the Umarex AirJavelin and the Umarex AirSaber are both single action that require the bolts to be pulled back in order to shoot them. The Umarex AirJavelin trigger is not as short, light or crisp as the Umarex AirSaber, the Umarex AirSaber for sure feels higher quality as expected.

View fullsize

Accuracy: This is going to be very interesting as I have never shot anything like this before but from what I was told at SHOT Show this year I can expect very accuracy results from both the Umarex AirJavelin and the Umarex AirSaber Archery CO2 and PCP Arrow Rifles. I’m not sure if I will test the Umarex AirSaber unless I can make a safe shooting range for it, luckily I live out on average so as long as I can setup a good backstop I should be able to test them both.

View fullsize

Build Quality: The build quality of the Umarex AirJavelin and the Umarex AirSaber Archery CO2 and PCP Arrow Rifles is very good overall, the Umarex AirJavelin is mostly plastic and is not very heavy but the fit and finish is good all round. The Umarex AirSaber on the other hand has a lot of metal used in the construction, the only real plastic found on the Umarex AirSaber would be in the stock. The Umarex AirSaber is for sure a step up in quality over the Umarex AirJavelin but will cost you almost double in the end.

View fullsize

Realism: This is going to be pretty short section since both the Umarex AirJavelin and the Umarex AirSaber Archery CO2 and PCP Arrow Rifles are not replicas of any actual gun in production. Their primary use is going to be for hunting and or pest control I would say.

View fullsize

Pros:

• Only Canada non PAL Airguns with enough power to hunt medium and larger game.

• Overall price point is good, nothing like this to compare to.

• Arrows are propelled from the front, no archers paradox when aiming.

• Arrows come with field tip arrows but can be unscrewed and replaced with broad tip arrows for hunting.

• Easy to use cross bolt safeties.

• Pistol grips allow for easy hold and control.

• Fit and finish is very good and excellent on the AirSaber.

• AirJavelin: 88 Gram CO2 for quick easy use.

• AirSaber: PCP for more power and larger game options.

• AirJavelin: White dot up front with fully adjustable peep sight on back.

• AirJavelin: M-Lock on sides for adding accessories.

• AirSaber: Picatinny rails on top for scope, sides and bottom for accessories.

• AirJavelin: Adjustable AR-style rear stock.

• AirJavelin: Rubber buttplate for added comfort.

View fullsize

Cons:

• No scope or sights with base model AirSaber so you will need to get one for it.

• Not a lot of shots per 88 gram CO2, will need a pump for the PCP AirSaber.

• Arrows are not cheap so make sure of your shots.

View fullsize

Comments:
The Umarex AirJavelin and Umarex AirSaber Archery CO2 and PCP Arrow Rifles are very interesting in that they are really the only Canada legal “firearms” that can actually put down small, medium and even large game without requiring a firearms license (PAL). This is because they do not exceed 500 fps, they do exceed the foot pound energy limit of 4.2 foot pounds but since both of these rifles do not exceed the 500 fps limit they do not exceed both requirements to place them in the regulated firearms category that requires a firearms license. This is great news for anyone in Canada without a PAL license that wants to be able to hunt various game or take care of pests humanly. Umarex has also been kind enough to bring us two variations on this design. The Umarex AirJavelin more economical and easier to use CO2 powered version designed for small to medium sized game and the Umarex AirSaber higher quality PCP powered big brother version designed to be used even for larger game. Both are great, all you need to do is pick which one is right for you!

My Table Top Review for the Umarex AirJavelin and AirSaber Archery CO2 and PCP Arrow Rifles:

• Buy the Umarex AirJavelin Archery CO2 Arrow Rifle in Canada

• Buy the Umarex AirSaber Archery PCP Arrow Rifle in Canada

• Buy the Umarex AirSaber Archery PCP Arrow Rifle with Scope in Canada

View fullsize

This is just my Preview for the Air-Ordnance SMG 22 .22 Caliber Full Auto Pellet Machine Gun. There will be more coming for sure for this one! Stay posted for my official Table Top and Shooting Videos later on.

I want to thank Drew from Tippmann Armory/Air Ordnance for sending me this unit for review. I have been wanting to get my hands one of these Air-Ordnance SMG 22 .22 Caliber Full Auto Pellet Machine Guns for several years now and super glad I happened finally :) I really don’t think there is any airgun out there like it. I am really hoping that we will be able to have this one in both our Canada and US Online Replica Airguns Stores.

View fullsize

So what exactly is the Air-Ordnance SMG 22 .22 Caliber Full Auto Pellet Machine Gun? It’s a PCP powered semi/full auto .22 caliber pellet firing Airgun and it is available in a Canada legal version that shoots just under 500 fps allowing it to be classified here in Canada as an unregulated Firearm. Unregulated Firearms do not require a license or registration and do not have to abide by the same rules that regulated firearms have to such as full auto limitations, magazine capacities and size limitations. So in other words if you want a full auto .22 caliber Machine gun here in Canada this is going to be your only option at least for now.

View fullsize

Some other cool features about the Air-Ordnance SMG 22 .22 Caliber Full Auto Pellet Machine Gun is the trigger setup, pull it light and quick and you get a single shot, pull and hold using medium force and you get full auto but not at a super high rate of fire. Press and hold the trigger down hard and you get full auto with a much faster rate of fire so you control the rate of fire by how hard you press the trigger down. Air-Ordnance SMG 22 .22 Caliber Full Auto Pellet Machine Gun also has an adjustment to set the maximum rate of full auto fire.

View fullsize

There are a few versions of the Air-Ordnance SMG 22 .22 Caliber Full Auto Pellet Machine Gun but they all share the same base components, gun just need to decide what add on you want to have with it. I am going to say make sure to get extra 100 round belts and a speed loader since the Air-Ordnance SMG 22 .22 Caliber Full Auto Pellet Machine Gun goes through a 100 round magazine fairly quickly!

View fullsize

That’s enough for now, more to come on the Air-Ordnance SMG 22 .22 Caliber Full Auto Pellet Machine Gun when I get back from my Holliday…

• Buy the Canada Legal SMG 22 Version

• Buy the US SMG 22 Basic Version

• Buy the US SMG 22 Tactical HPA Version

• Buy the US SMG 22 Tactical CO2 Version

View fullsize

The Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle is one that you are really going to want to take outside and set targets up around 50-60 feet await make it a little more challenging adn I do plan on getting outside with the Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle in a bit once the weather gets a bit nicer and have some fun shooting at longer ranges. For now I wanted to at least get out my Indoor Field Test Shooting Video where I can Chronograph the Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle and also see what it can do shooting at 30 feet out.

View fullsize

Sig claims the Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle to shoot .22 caliber lead pellets at up to 700 fps with a power output of 12 foot pounds. Using 14.5 grain lead pellets I placed 6 rounds though my Chronograph and averaged 585 fps with the fastest shoot hitting 611 fps. Keep in mind there are much lighter lead pellets out there and when it comes to alloy pellets they drop in weight even more so hitting 700 fps with a light grain lead or alloy pellet is very realistic. What about Sigs claimed 12 foot pounds of energy? I did the math and using a 14.5 grain pellet with a maximum velocity of 611 fps, these numbers produce just a hair over 12 foot pounds! Mission accomplished :)

View fullsize

What about accuracy, I have seen a few claims online that the Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle is not the most accurate Pellet rifle out there and you know what I don’t think that was the absolute intension when Sig thought this one up. After all it is a semi auto high capacity Airgun replica, not a target rifle. I still like to find things out for myself so of course I performed my accuracy test for the Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle shooting 10 rounds into a fresh paper target from 30 feet back using a seated and rested shooting position. For this test I was using a red dot scope with a 3x magnifier on it. My first 10 rounds did OK producing just over a 1 inch grouping, not super great but most of the rods (8 of them) all struck the target within about 3/4 of an inch.

View fullsize

At this point decided to empty the rest of the magazine so about 15 rounds on the same target to see if the grouping stayed the same or maybe even speed out a bit. I was a bit surprised to find that my second 15 shot grouping all stayed within the higher 10 shot group again producing about a 3/4 inch grouping with just those two first test outliers? Maybe it was me, maybe it was the pellets, maybe it was the Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle? The good news is you have 30 rounds to hit your target so even if a couple of them stray a bit you still got 28 left to get the job done.

View fullsize

The Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle is one of the coolest Air Rifles I have tested and now own, not only is it a great Replica Airgun but it also performs well and can be used for plinking or small pest control. All at even a fraction of the cost of shooting 22LR rounds and that’s not even that expensive compared to 9mm and larger ammo. Let’s hope Sig Sauer makes a detuned Canada version so we can offer it up in our Canada Replica Airguns Store and if you live in the US then checkout the US Store for Sig Sauer buying options.

• Buy Sig Sauer Airguns in the Canada Replica Airguns Store

• Buy Sig Sauer Airguns in the US Replica Airguns Store