In this Replica Airguns Field Test Shooting Video I test out the Cybergun Kalashnikov AK47 Tactical Folding Stock AEG Airsoft Rifle to see what the actual velocity is and what kind of accuracy we can expect shooting 30 feet down range into a paper target, I shoot in both semi auto (10 rounds) and then Full auto (A bunch of rounds) to see how this will asl effect the accuracy.
Make sure to also watch my Table Top Video Review for the Cybergun Kalashnikov AK47 Tactical Folding Stock AEG Airsoft to find out more about it’s specifications and features along with some nice close up video of it.
Starting off with the velocity portion of this Field Test Shooting Video, I placed 6 rounds through my Chronograph using .20 gram Airsoft BB’s and averaged 384 fps. The slowest shot was 380 fps while the fastest shot was 390, so only a 10 fps spread! This is a nice velocity as it’s not too hot for indoor skirmishes or too slow for further out shooting outside.
Next I setup a fresh paper target 30 feet down range and proceeded to test out the Cybergun Kalashnikov AK47 Tactical Folding Stock AEG Airsoft Rifle in both semi auto and full auto to see what kind of grouping I could expect. I did not sight in the Cybergun Kalashnikov AK47 Tactical Folding Stock AEG Airsoft Rifle as I like to see how they perform right out of the box. I did notice I was shooting a little bit high and just slightly to the left. Elevation adjustment can be easily adjusted using either the front post sight, the rear notch sight or even a little bit with hop-up so this is not a problem. There is however no way I could see to adjust windage so any corrections you may need ot make left to right you will have to do using your aim point. That said I was able to get around a 1.5 inch grouping with 10 rounds in semi auto mode.
Switching things up to Full auto so fun mode I proceeded to place a whole bunch of rounds into the target, I will estimate around 75 or so and the grouping only spread out to about 2 inches so semi or full auto you will get great accuracy with the Cybergun Kalashnikov AK47 Tactical Folding Stock AEG Airsoft Rifle! The rate of fire using an 8.4 volt battery is not super fast but the cycle rate on a real steel AK47 is also not super fast but if you want to speed it up and also have a more responsive trigger then I would suggest using a higher voltage LiPo battery.
I was very impressed overall with the Cybergun Kalashnikov AK47 Tactical Folding Stock AEG Airsoft Rifle as it is a relatively inexpensive Airsoft Rifle with lots of included bonuses like two magazines, a battery and charger. Even with the low price and bundled add ons it performed really well for me. SO if you are looking for an AK type Airsoft Rifle I would suggest you take a look at the Cybergun Kalashnikov AK47 Tactical Folding Stock AEG Airsoft Rifle as an option for sure!
Type: Airsoft AEG. Distributer:Cybergun Model:Kalashnikov AK47 Tactical 60th Anniversary. Materials: Metal and polymer build. Weight: 6.82 pounds (3100 grams). Barrel: 457mm (18 inches) Total Length: 709-950mm (27.9-37.4 inches). Propulsion: AEG. Action: Semi, full auto. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: 550 rounds. FPS: 400.
Trigger Pull: The trigger pull on the Cybergun Kalashnikov AK47 Tactical Folding Stock AEG Airsoft Rifle is what you will find on most electric switch controlled AEG Airsoft Guns. It has a short to mid length very light take-up with a light release which generally has a bit of a delay as the motor pulls the spring back and release the piston. This delay is shorter with higher voltage batteries as the motor will run quicker allowing for a shorter delay and also a higher rate of fire in full auto mode.
Accuracy: I have not performed my Field Test Shooting Video for the Cybergun Kalashnikov AK47 Tactical Folding Stock AEG Airsoft Rifle but plan to get to that video this week. I really have no idea what to expect at this point since i have not even loaded up a magazine so we will find out together when I get to my Indoor Field Test Shooting video in a couple of days.
Build Quality: Overall the Cybergun Kalashnikov AK47 Tactical Folding Stock AEG Airsoft Rifle seems fairly well built. You will find metal parts in the barrel, front and back sights, receiver, charging bolt, bolt cover, rings, trigger and trigger guard. The plastic components would be the folding stock, magazine, RIS hand-guard, fore-grip and pistol grip. Fit and finish seem good and the overall weight is heavy but not too heavy. Internally you get a metal gear box with metal gears so you should expect to have a reliable and long lasting shooting experience with this Airsoft Rifle.
Realism: The Cybergun Kalashnikov AK47 Tactical Folding Stock AEG Airsoft Rifle for sure looks the part of a more modern tactical AK47 with the majority of the mechanical parts functioning like a real steel version as in the charging bolt, bolt cover, sector switch, foldable rear stock and of course the magazine release.
Pros:
Mostly metal construction with good overall weight and feel.
Lots of rail attachment options on RIS rail hand-guard.
Adjustable sights, smaller increments on front, easy quick adjustment for elevation at distance on the back.
Comes with a folding fore-grip.
Rear folding stock helps to shorten up the rifle in transport or for storage.
Comes with two high capacity magazines.
Comes with a battery and charger.
Comes with sling mounts and a basic sling.
Super easy access to change out the battery.
Easy access to hop-up via charging bolt.
FPS should be nice and high, good for long or mid range shooting.
Cybergun Kalashnikov licensed, also 60th Anniversary edition.
Orange tip should be easy enough to remove.
Price point is fairly good for all that you get.
Cons:
No simulated blowback action.
Sights are only adjustable for elevation.
Magazines are plastic, feel a bit cheap and light.
Comments: The Cybergun Kalashnikov AK47 Tactical Folding Stock AEG Airsoft Rifle is what I would consider a great value AEG Airsoft Rifle and there are not as many AK style Airsoft Rifles to choose from as there are AR’s so it’s nice to see this one in the lineup. You do get a lot for what you are paying, lots of metal parts externally and internally with a hefty almost 7 pound weight to it. I also like that you get everything you need to get going other than the Airsoft BB’s, so you get the battery and charger along with two 500+ magazines, they even add in a cheap sling just in case you want to throw it over your shoulder!
My Vimeo Table Top Review Videos for the Cybergun Kalashnikov AK47 Tactical Folding Stock AEG Airsoft Rifle:
Took me a while to get to this Field Test Shooting Video for the ASG CZ Scorpion EVO 3 A1 6mm AEG Airsoft Gun but glad I took a look at it even if it is over 6 years already on the market. As per usual I test out the velocity shooting several ordains through my Chronograph to see what the real world fps is, I then follow this up with an accuracy test shooting 10 rounds on a paper target setup 30 feet downrange to see how tight of a grouping I can get. Also make sure to watch my Table Top Video for the ASG CZ Scorpion EVO 3 A1 6mm AEG Airsoft Gun for information on the specifications and features along with some nice close up video.
Starting with my Velocity Test I placed 6 rounds through my Chronograph using .20 gram Airsoft BB’s clocking in an average of 421 fps. I was very impressed with the consistency of the velocity with the lowest shot being 420 fps and the fastest shot being 422 fps only 2 fps apart! You can change out the spring super easy on the ASG CZ Scorpion EVO 3 A1 6mm AEG Airsoft Gun but I feel that the fps out fo the box would be good for most Airsoft games indoor and outdoor.
I then places a brand new paper target 30 feet downrange and proceeded to shoot 10 rounds at it in semi auto using a seated shooting position rested on a sand bag up front. I was able to get very close to a 1 inch grouping just a tad over an inch. I did not sight in the gun so I was not surprised I was shooting rather low and just a hair to the left, this could be equally corrected by adjusting the rear sight for windage and elevation. I could also play around with the hop-up effecting elevation at different ranges. I then proceeded to shoot take some more shot in both 3 round burst adn full auto modes and as expected the groupings did spread out a bit but not a lot.
I was super impressed with eh performance of the ASG CZ Scorpion EVO 3 A1 6mm AEG Airsoft Gun, I don’t think I have seen velocity consistency this good in any other AEG Airsoft gun I have tested so far. Accuracy was also on point even using lighter plastic .20 gram Airsoft BB’s. My only real grip with the ASG CZ Scorpion EVO 3 A1 6mm AEG Airsoft Gun is the limited battery choice since the internal storage ares is very constricted. Other than that this Airsfot Gun is a winner and worth taking a look at if you can get your hands on one.
Type: Airsoft AEG. Distributer:ASG. Model: CZ Scorpion EVO 3 A1. Materials: Metal and polymer build. Weight: 5.3 pounds (2400 grams). Barrel: 208mm (8.2 inches) Total Length: 425-623mm (16.7-24.5 inches). Propulsion: AEG. Action: Semi, burst, full auto. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: 75 rounds. FPS: 395.
Trigger Pull: The trigger pull on the ASG CZ Scorpion EVO 3 A1 6mm AEG Airsoft Gun is essentially just an on off electric switch controlled by the ECU. There is very little trigger resistance and the take up is very short allowing for quick semi auto shooting but if you like you can easily select three round burst or full auto shooting for more intense situations.
Accuracy: I have not performed my Field Test Shooting Video for the ASG CZ Scorpion EVO 3 A1 6mm AEG Airsoft Gun but plan to get to that video next week. I really have no idea what to expect at this point since i have not even loaded up a magazine and taken it for a spin yet. I am sure I will not be dissapoitned as this is a very high quality Airsoft Gun with great internals.
Build Quality: I remember at SHOT Show back when ASG introduced the ASG CZ Scorpion EVO 3 A1 6mm AEG Airsoft Gun, I was told indirectly that the construction was nearly identical to the real steel CZ Scorpion EVO at least cosmetically as all the internal parts will be specificities to Airsoft. That said this is a very high quality build with the material being for the most part the same as the original with Nylon Fiber PA6 Polymer reenforced plastics and even some CNC machined metal parts as in the outer barrel, flash hidden, barrel nut and even the gear box.
Realism: The ASG CZ Scorpion EVO 3 A1 6mm AEG Airsoft Gun is a bang on replica in terms of emulating the real steel CZ Scorpion EVO and has our weight and feel including a blot catch that locks back when out of ammo and most working components being ambidextrous.
Pros:
Build quality is almost exactly like the real steel version, super high quality materials.
Three shooting modes: semi auto, burst mode and full auto.
Decent mid capacity 75 round magazine with auto empty detection which locks the bolt catch.
Quad rail for lots of add on accessories.
Folding and adjustable stock that can also be removed.
Adjustable and removable iron sights with fiber optic up front and peep in the back.
Working charging handle for easy access to hop-up
Working bolt catch.
High quality electronic and gear box.
Ambidextrous controls for the most part.
Scorpion licensed through ASG.
Orange tip is fairly discreet.
Cons:
Battery compartment is small and hard for quick battery replacement, I recommend using an external setup if possible.
Price point is on the higher side but you get what you pay for.
Comments: On paper and just by looking over and inspecting the ASG CZ Scorpion EVO 3 A1 6mm AEG Airsoft Gun specs out and I am sure I will be pleased when I test it out in the Replica Airguns Indoor Shooting Range. That said this hasn’t happened yet so I will leave my final thumbs up until then. I do wish we had them in stock at the time of this video but there are a lot of other great ASG products in our store and of course many more brands of AEG Airsoft Guns. Hopefully we can get something like this in shortly for everyone so keep checking with us.
My Vimeo Table Top Review Videos for the ASG CZ Scorpion EVO 3 A1 6mm AEG Airsoft Gun:
In this Field Test Shooting Video I put the Webley Valuemax 22 Caliber Spring Piston Break Barrel Rifle through my standard Replica Airguns Indoor Field Test protocol by first testing out the velocity and placing 5 rounds through my Chronograph to see what the actual real world fps is using 14.3 grain lead pellets. I then setup a fresh paper target 30 feet downrange and place 10 pellets into it to see what type of grouping I can get. If you have not already watched my Table Top Video for this Break Barrel Spring Piston Pellet Rifle then make sure to do so for more details, specifications and close up video.
Starting off with my real world velocity test for the Webley Valuemax 22 Caliber Spring Piston Break Barrel Rifle, I went with 14.3 grain lead pellets which are I would say on the heavier side. Even so I managed to hit 478 fps which produced a nice 7.26 foot pounds of energy which by the way is almost 10 Joules! If you are wondering about Canadian legalities, as long as I do not go over 500 fps AND go over 4.2 foot pounds (both thresholds must be exceeded), then this Airgun is considered a non-regulated firearm and does not require a firearms license.
Moving on to the accuracy portion of my Indoor Field Test in the Replica Airguns Sea Can. As always I placed a brand new paper target 30 feet downrange and proceeded to shoot ten 14.3 grain lead pellets from a rested and seated shooting position to allow for best possible results with as little human error but I am imperfect so some human error is always present. I was using the open fiver optic sights on the Webley Valuemax 22 Caliber Spring Piston Break Barrel Rifle rather than a scope even thought there is a dovetail rail with included scope stop. To be honest I was expecting a better grouping, something close to half an inch but on this day with this ammo choice I was closer to 1.5 to even 2 inches. I did see several pellets land in a tighter sub group but some came out of this group enlarging the grouping. I would like to try a different pellet choice to see if I can do better as I believe this rifle has way more potential.
In terms of power the Webley Valuemax 22 Caliber Spring Piston Break Barrel Pellet Rifle is about has high as you can go before it becomes a regulated firearm here in Canada so no complaints in that department. Again I was disappointed in the accuracy but I honestly believe a different pellet choice could fix that problem as I have seen often with other Pellet Rifles. Once the right pellet choice is made and granted a more consistent and tighter grouping is achieved, this Spring Piston Pellet Rifle could make a decent small pest control airgun!
Type: Pellet Rifle. Distributer:Webley & Scott. Model:Valuemax. Materials: Metal and polymer build. Weight: 6.4 pounds (2900 grams). Barrel: 17.7 inches (450mm), rifled. Total Length: 43 inches (1092mm) Propulsion: Spring Piston Action: Break Barrel. Ammunition Type: .22 Caliber Pellets. Ammunition Capacity: Single Shot. FPS: 499.
Trigger Pull: The trigger pull on the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle is fairly nice There is a little bit of very light take up followed by a vert light release , the take up or travel length can be adjusted on this Air Rifle but that is the only trigger adjustment you can make and perhaps all that is needed.
Accuracy: I have not performed my Field Test Shooting Video for the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle but I did get to take around 20 or so shots with it when I was trying to get it to diesel for me. It looks ot me like it is going to be nice and accurate as I was not even really going for accuracy and it seemed to already be grouping fairly tight. I was recoding fps using my Chronograph as I was trying to find out if by adding some oil to the spring piston chamber could get it to diesel which it never did for me, I was however to establish that the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle shot right around 470-480 fps using 14.3 grain lead pellets which worked out to right around 7.32 foot pounds of energy. I will know a lot more when I do my official Field Test Shooting Video next week.
Build Quality: Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle is built to be a value priced Airgun hence the name (Valuemax), that said it is maid well enough with lots of metal and of course some plastic or in this case mostly nylon as the stock is a solid nylon piece. Other than the stock the plastic parts are found to be in the sights and trigger guard, everything else seems to be metal.
Realism: The Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle is not a replica or copy of any real steel gun in production but it does look like a traditional hunting rifle in basic shape so make sure to transport thank airgun as if it was a real gun. Either in a gun case or perhaps a blanket in your trunk and always obey any laws for gun position and transportation in your area.
Pros:
Inexpensive price tag for well made decent performer.
Initial test showed to have good accuracy and power! (more to come).
Fully adjustable sights with optical TRUGLO Fiber Optics.
Can add a magnified optical scope using the top built in dovetail rail.
Nylon fiber stock is durable and functional with the addition of a vented rubber buttplate.
Trigger feels decent and is also adjustable for travel length.
Rear thumb safety resets after each break of the barrel.
Nice light and short single action trigger.
Would be good for small pest control because of decent FPS and good accuracy.
Cons:
Included sights are mostly plastic.
The Valuemax version has a more basic less adjustable trigger.
Detuned down to under 500 fps for Canada import as non-regulated Firearm.
Comments: I am looking forward to performing my Indoor Field Test Shooting Video for the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle to see what it can really do in terms of accuracy so stay posted for that video next week. Overall if you are lucky enough to already have one or can get your hands on one since this rifle is discontinued in some area, I think this is a great Break Piston Air Rifle especially if you live in Canada and want the most bang for your buck. I am not only talking about cost verses features, I also mean power and energy since the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle is a .22 caliber Air Rifle that can shoot really close to 500 fps with a nice heavy grain lead pellet achieving decent energy levels reasonable enough for small pest control. The Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle is not feature less, it does include a reseting safety, anti bear trap system, dove tail mounts with an included scope stop, fiver optic adjustable sights and a vert ergonomic textured nylon stock. All in all great value for what you pay!
My Vimeo Videos for the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle:
In this Field Test Shooting Video I put the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle through the regular Replica Airguns Indoor Field Test by first testing out the velocity and placing several rounds through my Chronograph to see what the actual fps is using both .20 gram and .40 gram Airsoft BB’s. Then I setup a fresh paper target 30 feet downrange and place 10 rounds into it to see how tight of a grouping I can get. If you have not already watched my Table Top Video for this Sniper Airsoft Riffle, then make sure to do so for more details, specifications and close up video.
Starting off with my real world velocity test for the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle I decided to use both .20 and .40 gram Airsoft BB’s to see what a difference of double the weigth form the claimed for would actually be since for the most art this Airsoft Sniper Rifle is really meant to be using heavier Airsoft BB’ closer to the .40 gram weight. I was kind of expecting the heavier .40 gram BB’s to shoot almost half as fast since they where double the weight bu this was not the case! I shot 5 rounds with each weight Airsoft BB and with the .20 gram I averaged 479 which was actually faster than claimed, When I switched up to the .40 gram Airsoft BB’s I was surprised to get an average of 373 so only around 100 fps slower!
Moving on to the accuracy portion of my Indoor Field Test here in the Replica Airguns Sea Can, as always I placed a fresh paper target 30 feet downrange and proceeded to shoot 10 .40 gram Airsoft rounds into it from a rested and seated shooting position to allow for best possible results with as little human error added in. I was using a 4x optical scope since the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle has a the added rail on top just fo this purpose and I would imaging most people are going to want to add a magnified scope to this Airsoft Sniper Rifle rather than use the built in pop iron sights that by the way are not adjustable. I know 30 feet is not the range one would be shooting this rifle at but it’s all I have for an indoor shooting range and it will give us an idea of what we can expect shooting further out… as in a nice tight group at 30 feet is going to mean better accuracy than a spread out grouping art 30 feet. I will say the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle probably got one of the best groupings for an Airsoft Rifle that I have tested at 30 feet placing all 10 rounds within about an inch to an inch an a half.
I would like to take this Airsoft Sniper Rifle outside and see what it can do at much further out ranges again using nice and heavy Airsoft BB’s when it gets a bit warmer and stops raining so much :) But for now my Indoor Field Test performed about as good of a result as I can expect. The ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle is a really well made which paid off in two it performed for me. I don’t really see any need to upgrade this Airsoft Sniper Rifle other than adding an optical scope and perhaps investing in some high quality Airsoft Ammo.
Type: Airsoft Rifle. Distributer:ASG. Model:Steyr Arms Scout. Materials: Metal and polymer build. Weight: 6.5 pounds (2950 grams). Barrel: 14.5 inches (368mm), non-rifled. Total Length: 39.5 inches (1000mm) Propulsion: Spring Piston Action: Bolt action repeater. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: 32 round magazine. FPS: 443. Type: Black and Grey versions.
Trigger Pull: The trigger pull on the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle is short light and crisp. Working the bolt precooks the trigger for single action only shooting allowing for just the release of the hammer. There is very little take up and no creep at all, just a nice light and predictable trigger pull.
Accuracy: I have not performed my Field Test Shooting Video for the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle so stay posted for that. ASG claims around 4430 fps velocity with the preinstalled M140 spring, you can upgrade the spring all the way up to an M190 spring for even higher potential fps. In terms of accuracy I am also expecting good results so check back next week for my Indoor Field Test Shooting Video for the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle.
Build Quality: The ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle is well built with lots of high quality component not only inside but also internally. You will find a metal barrel and receiver along with metal bolt, trigger and rear sight, the front sight is however plastic. I donate really thin k you will be using the pop sights all that much as they are not adjustable and this gun really begs for a nice optical scope. The nylon polymer stock has micro-texturing to help with the grip in all weather conditions.
Realism: The ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle is based on the real steel 7.62 NATO Steyr Scout and even incorporates the integrated folding bipod legs like the original. For the most part they look identical but you will find the actual magazine on the Airsoft version is placed further up the stock to allow for the feeding of the Airsoft BB’s which does make the actual inner barrel shorter by about 4-5 inches.
Pros:
Nylon Polymer stock with micro-texturing.
Railed metal receiver with laser-etched Steyr trademarks.
Integrated folding bipod legs on left and right sides of the stock.
Flip-up backup front and rear sights.
Accessory slot on bottom of stock for mounting of optional bipod rail.
Millet QD sling loop attachment points.
Front dummy magazine.
Rear dummy magazine with storage for a spare magazine.
Removable stock spacer pads for length-of-pull adjustment.
90 degree trigger with steel sear.
90 degree aluminum piston with dual glide rings and steel base.
Silent Air Brake piston head.
Silent cylinder head with shock-absorbing padding.
9mm stainless steel ball bearing spring guide.
Bore-up steel cylinder with 12.5% more air volume than stock cylinders.
Hop-up unit with both side-lever adjustment and TDC screw adjustment options.
Steel CNC-machined hop-up arm.
03mm tight-bore inner barrel.
60 degree Modify Predator enhanced hop-up bucking preinstalled (50 and 70 degree buckings available separately).
Compatible with VSR-spec inner barrels.
450 FPS with pre-installed M140 spring.
Can take up to a M190 spring with no upgrades needed.
Cons:
32-round magazine.
Recommended ammo: 0.36g BBs and above, 0.4g optimal.
Comments: I am looking forward to performing my Indoor Field Test Shooting Video for the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle. I won’t be able to test it out perhaps as far range as I would like to since I will be shooting it in the Replica Airguns Indoor Shooting range which allows me to test at 30 feet. That should give me a good overall idea on at least what it may be capable of since if we can get a tight group at 30 feet we should also be able to get a tight group at longer ranges with proper hop-up and heavier BB selection. I do plan on placing a scope on the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle to give it the best possible chance of performing at it’s best and really hope to see a good result from it.
My Vimeo Videos for the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle:
In this Field Test Shooting Video I put the ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun through it’s paces by first testing out the velocity placing several rounds through my Chronograph, and then I setup a paper target downrange and place 10 rounds into it to see how tight of a grouping I can get. If you have not already watched my Table Top Video for this Airsoft Sniper Pistol/Rifle then make sure to do so for more details, specifications and close up video.
Starting off with my real world velocity test for the ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun, I decided to use .28 gram Airsoft BB’s for this entire Field test Shooting video so I was expecting to get somewhere between 20-25% slower fps velocity as compared to the standard tested .20 gram Airsoft BB’s. After placing around 6 shots through my Chronograph I averaged 328 fps which ended up being 18% slower than the claimed 400 fps made by ASG. I would image if I had used .20 gram Airsoft BB’s I may have even exceeded 400 fps.
Moving on to the accuracy portion of my Indoor Field Test here in the Replica Airguns Sea Can, as always I placed a fresh paper target 30 feet downrange and proceeded to shoot 10 rounds into it from a rested and seated shooting position to allow for best possible results with as little human factor added in. I was using a 4x optical scope since the ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun does not come with any type of sighting system included so I did have to sight it in initially. I did manage to get a nice 1.5 inch grouping fairly close to the bullseye but I did notice that if I angled the barrel down a bit, BB’s would roll out of the barrel which made me wonder if the hop-up was set high enough to engage a BB.
So I did my second test with the hop-up set in the middle range and this time BB’s did not fall out of the barrel when angled down. After the hop-up adjustment I did notice I was shooting a bit higher which is expected with more hop-up adjustment so if you are experiencing BB’s falling out of the barrel then make sure to adjust your hop-up a bit tighter.
All in all the ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun performed very well for me especially once I got the hop-up figured out. And I do think it makes for a really nice compact Sniper Rifle if bulkiness is a factor for you, if not then checkout the Rifle version of this gun with the more traditional but-stock and longer barrel.
Type: Airsoft Rifle. Distributer:ASG. Model:Action Army T-11. Materials: Metal and polymer build. Weight: 3.9/4.5 pounds. Barrel: 11.8 inches, non-rifled. Total Length: 34.7/43.3 inches Propulsion: Spring Action: Bolt action repeater. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: 50 round magazine. FPS: 400-430. Type: Pistol and Rifle versions.
Trigger Pull: The trigger pull on ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun is light, short and crisp. There is virtually no take-up and the release point has no creep to it. I would say it is not too light but for sure one of the lighter trigger s I have tested on a Airsoft rifle.
Accuracy: I have not performed my Field Test Shooting Video for the ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun so stay posted for that. ASG claims around 400-430 fps velocity depending on the version which is kind of weird since both have the exact same barrel length internally and I would assume both use the same mechanical part throughout? I don’t have the rifle version to compare to but I will for sure test the velocity using my Chronograph for the pistol version when I do my Field Test Shooting Review along with accuracy performance.
Build Quality: The ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun is well built for sure, it feels really solid in the hadn't and has good overall weigth to it for it’s size. You will find lots of metal parts where they need to be as in the inner and outer barrel, receiver, bolt, trigger, magazine release and I am sure most mechanical internal parts. Fit and finish is also very good.
Realism: The ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun is not a replace of any gun I know of but does have tab least the pistol version does look like a sawn off shotgun more than a sniper rifle. The gun overall all is very modern and ergonomic looking but in terms of being a replica of any specific real steel gun in production I don’t know of any it would resemble?
Pros:
Top and bottom rails for lots of accessory add on options.
Can swap over to a rifle version by adding on an interchangeable but-stock.
Mock magazine allows for storage and transport of tools plus extras.
Safety switch is in a great location for right handed shooters.
Comes with included hand stop.
Solid construction with lots of metal parts where they are important.
Ability to add side rails.
Great option if you are looking for a more compact sniper rifle.
Comes in Pistol and Rifle versions.
Cons:
Has an orange tip.
Does not come with sights, will need to add some sort of optical or red dot sight.
Does not come with speed loader, would have been nice.
Comments: I am looking forward to performing my Indoor Field Test Shooting Video for the ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun. I won’t be able to test it out perhaps as far range as I would like to since I will be shooting it in the Replica Airguns Indoor Shooting range which allows me to test at 30 feet. That should give us a good overall idea on at least what it may be capable of since if we can get a tight group at 30 feet we should also be able to get a tight group at longer ranges with proper hop-up and BB selection. I like the option of being able to choose either the Pistol or Rifle version and both should perform about the same. Having the Pistol version will allow for a much more compact Sniper Rifle option much better suited for shooting in a variety of situations.
My Vimeo Videos for the ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun:
Make sure to watch my Table Top Video Review where I go into more detail about the specifications and details along with some nice close up video of the Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle.
In this Vimeo Video Field Test Review I test out the Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle in the indoor Replica Airguns Shooting Range to see how accurate it is and what kind fo velocity we can expect from it.
Starting with the velocity test I averaged out 8 rounds through my chronograph using 8.18 grain lead pellets using the dual 12 gram CO2 setup and I was able to average 445 fps which is not bad as these are mid grain weight pellets, lighter weight pellets would for sure get closer to the 490 fps claimed by Umarex. The temperate was about average room temp so not overly cold or warm.
Moving on to the accuracy test I placed all 9 rounds from the rotary magazine into a fresh paper target setup 30 feet away. I use a reseted seated position in the back with the Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle resting on a sand bag up front and I was using the 4 power scope for this test which I setup earlier. My final result was for sure an under one half inch grouping, I did feel like I pulled one shot a little bit but I am sure this Airgun can get quarter inch groupings at 30 feet and I would expect half inch groupings at 50 feet so perfect for mid range small pest shooting.
Umarex does adversities this Air rifle as being very quiet but in Canada we are not allowed to have any type of suppressor even on airguns so I believe this Canada version has been disabled in that regard but the Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle is fairly quiet for sure with its long barrel and slightly lower fps than the US version. Overall the Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle is a lot of bang for the buck with the added 4x scope, included magazines that hold 9 rounds each and the ability to use either a dual 12 gram or single 88 gram CO2 setup. It also looks really cool and performs just as good!
Type: Pellet Rifle. Distributer:Umarex. Model:Fusion 2. Materials: Metal and polymer build. Weight: 6.5pounds (2948 grams). Barrel: 22.5 inches, rifled. Total Length: 40.3 inches Propulsion: 12 gram CO2 x2 or 88 gram CO2 x1 Action: Bolt action repeater. Ammunition Type: .177 caliber pellets. Ammunition Capacity: 9 round rotary magazine x2. FPS: 490.
Trigger Pull: The trigger pull on Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle feels pretty good, it is fairly short and light having a claimed 3.5 pound release which is believable. You will need to obviously work the bolt for each shot that precooks the internal hammer/striker allowing for the short and light trigger.
Accuracy: I have not performed my Field Test Shooting Video for the Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle so stay posted for that. Umarex has claimed a velocity of around 490 FPS for the Canada version I will be testing, the US version has a claimed velocity of up to 700 for those in the US purchasing this Rifle. I am sure the included 4x32 optical scope once setup will help in the accuracy department when I test this CO2 Air Rifle out on a paper target setup 30 feet down range.
Build Quality: The Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle is a fairly low cost target pellet Rifle when you consider it comes with a decent optical scope along with two 9 round magazines but even so the build quality seems very solid coming in at 6.5 pounds. The stock is plastic of course but there is lots of metal where you want it to be as in the bolt, trigger, safety and most other mechanical parts.
Realism: The Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle is not a replace of any gun I know of but does sport a very modern ergonomic look with its pistol grip and molded full stock. I like the built in picatinny rail which even though it does not offer any type of open sight configuration will allow for a variety of scope mounting options for near or far shooting.
Pros:
Low cost for a full featured Air Rifle with included scope.
Nice ergonomic modern looking design.
Ability to use either 12 gram or 88 gram CO2 cartridges.
Comes with 4x32 optical scope and all mounting hardware needed.
Come with two 9 round rotary magazines.
May be very quiet if the SilencAir technology is not disabled here in Canada?
Single action 3.5 pound trigger fells good.
Safety is large and easy to use.
M-LOK slots for mounting additional hardware.
Cons:
No iron sight option if you would prefer that.
Limited to under 500 fps (Canada version).
Not sure about the functionality of the SilencAir technology in Canada?
Comments: I am looking forward to performing my Indoor Field Test Shooting Video for the Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle to see if it performs as good as it looks. I’ll probably use the duel 12 gram configuration for this test since I don’t plan on shooting 300 rounds with it for my testing. We should also find out if the SilencAir technology has been disabled or not with my Canada version but even so, a 500 fps Air Refile is not going to be all that loud either way at the end of the day. There are not a lot of Bolt Action multi shot pellet Air Rifles out there especially in this price range so I am really hoping it hits a home run when I test it so stay posted for that video…
My Vimeo Videos for the Umarex Fusion 2 CO2 .177 Caliber Bolt Action Pellet Rifle:
In this Preview Unboxing Video I do an Unboxing and take a quick look at three Bolt Action Rifles, two spring powered Airsoft Rifles from ASG and a dual CO2 powered Pellet Rifle from Umarex.
Wow, an accessory review, not many of these :) Today I take a look at the Amomax Airsoft Airgun Holster product line since at some point you may want to put your gun in a holster or practice drawing your gun from a holster?
The good news is we just got in a decent amount of product for our Amomax Airsoft Airgun Holsters. Here is a bit of info about Amomax but of course make sure to watch the video as I take a good look at a few of the versions we sell in our Canada and US online Replica Airguns Stores.
Amomax holsters are compatible with 4 different carrying platforms :paddle (standard), belt clip, MOLLE, and drop leg platforms. All the carrying platforms can be replaced by only one screw. Users can carry them in daily use, outdoor sports, normal shooting training and competition. Holster will stay firmly on a belt, leg and MOLLE system even in fast moving situations with a quick release Retention System button that keeps the gun locked in place until you are ready to draw. Holster body and carrying platform are connected with a tooth gear that allows for 360 degrees of rotation. User can easily adjust the carrying position to fit their needs.
Amomax Holsters are currently available in the following versions:
Today I decided to get outside since the weather was nice and make my Field Test Shooting Video for the ASG TAC-6 CO2 Airsoft Rifle (actually outside in the filed!) After all the ASG TAC-6 CO2 Airsoft Rifle is a sniper rifle and so I wanted to test it out at longer ranges than my 30 foot indoor shooting range can allow for. So I setup two paper targets at around 40 feet and 80 feet out, the actually distance may have been longer than that?
Starting off my Field Test Review I placed five .25 gram plastic Airsoft BB’s through my Chronograph and averaged 446 fps which is 6 fps faster than the claimed 440 fps from ASG. And that was with .25 gram Airsoft BB’s so if I was using lighter .20 gram BB’s I would expect velocity closer to around 500fps so don’t be shooting anyone with this Airsoft Rifle at close ranges!
Next I proceeded with my accuracy test placing 5 rounds on the target setup around 40 feet downrange. I managed to get all 5 rounds within about 2 inches of each other, not bad since this is a good 10 feet more than I usually test my Airsoft Rifles at. With the remaining 10 rounds in my magazines I was hoping to get at least a couple shots on my paper target setup a good 80 feet away but did not have much luck, I even reloaded the 15 round stick magazine 2 more times and gave it a go but again with no success! The Airsoft BB’s seemed to want to angle off in all direction usually up and to the right or left right before the 80 foot target, perhaps I would have had much better luck at 60 feet?
All I can surmise from this higher range Field Test is that the ASG TAC-6 CO2 Airsoft Rifle is not really a long range Airsoft gun at least with the .25 gram Airsoft BB’s I was using, maybe heavier Airsoft BB’s would settle down a bit more? I can say at ranges up to 40 feet the ASG TAC-6 CO2 Airsoft Rifle did perform just fine so keep that in mind when looking into buying one of these as smoking cans at 30-40 feet will be no problem and make for some fun times in the back yard or even basement makeshift gun range.
Type: Airsoft Rifle. Manufacturer: ASG. Model:TAC-6. Materials: Plastic with some internal metal parts. Weight: 3.5 pounds (1588 grams). Barrel: 12 inches, metal non-rifled. Length: 36 inches. Propulsion: 12 gram CO2 x 1. Action: Semi auto, double action only. Ammunition Type: 6mm BB's. Ammunition Capacity: 15 round metal stick magazine. FPS: 440.
Trigger Pull: The double action only type trigger pull on the ASG TAC-6 CO2 Airsoft Rifle is not too heavy but it is rather long so really quick rapped fire shooting will require some finger work. The trigger reset is right at the begging of the pull so you need to make sure you allow the trigger full range of motion or you may miss the odd shot.
Accuracy: I haven't done my Field Test Shooting video just yet for the ASG TAC-6 CO2 Airsoft Rifle but will shortly so stay posted for that video. ASG claimed the fps to be right around 440 and I am assuming with .20 gram Airsoft BB’s, I will most likely busing .25 gram Airsfto BB’s for my testing so I am hoping for around 400 fps or so. With the fiber optic front sight and fully adjustable rear peep sight I shoudl be able to get some decent rounds on target downrange and hopefully get a nice grouping.
Build Quality: The ASG TAC-6 CO2 Airsoft Rifle is mostly plastic but feels pretty good in the hand with decent fit and finish. There are some metal internal part along with the outer barrel and top rail but for the most part the ASG TAC-6 CO2 Airsoft Rifle is all plastic including the trigger and front and rear sights.
Realism: The ASG TAC-6 CO2 Airsoft Rifle is not a replica of any modern rifle that I know of but it does look a bit like a Beretta CX4 Storm especially the back half of it. The flash hider and top and bottom raise add to the realism. Available From: The Replica Airguns Store.
Pros:
Very customizable with rails top and bottom.
Comes with a rather nice Bipod that can be used with other rifles.
Front and back removable Iron sights are very usable, fiber optic in front, peep in back.
Safety switch is in a great location for right handed shooters.
Canada version comes with black flash hider.
Mostly plastic but solid construction.
Rubber Butt Pad is nice and thick.
Removable barrel to reduce size for easier transportation.
Also come in 4.5mm Steel BB version.
Optional Integrated laser can be added.
Cons:
DOA Trigger pull is a bit long which will slow down rapid fire shooting a bit.
Mostly Plastic Polymer build.
Why not a longer inner barrel for possible more fps?
CO2 is in the Pistol grip and not the magazine so may not be great for on field battles.
Comments: This may not be the most exciting Airsoft Rifle I have reviewed, it does look kind of cool and the price is right compared to other Airsoft Rifles. Who is it really for? I would say someone looking for an Air Rifle for plinking in the backyard or basement that perhaps want's a little bit more safety in terms of using plastic BB’s rather than Steel BB’s. Sure you can use the ASG TAC-6 CO2 Airsoft Rifle for Airsoft wars but most people want something a bit more realistic in terms of looks and function. Because the ASG TAC-6 CO2 Airsoft Rifle does have built-in Popup it shoudl be able to reach out to longer ranges so we will have to see if it can perform decent at longer ranges when I do my Field test Shooting Video.
My YouTube Table Top Review Video for the ASG TAC-6 CO2 Airsoft Rifle:
I will say right off the bat this Field Test Shooting Video for the Air Venturi 3000 PSI Aluminum HPA Tank with Stock and Adapter did not go as well as I would have wanted it to! The HPA tank itself worked really well but I believe the adapter was faulty as it was destroying the seals on my tank and not regulating very well.
I still wanted to publish this video regardless as not all reviews go as planned, some fail horribly but I would rather be honest and transparent about it rather than have you believe every product is a perfect.
There will always be problems even with really great products there can be defects. I plan to get a new adaptor and try this Field Test Review Video again but for now you can have some fun watching me at least have some success using the Air Venturi 3000 PSI Aluminum HPA Tank with Stock on my Rap4 Rap5 MP5.
You can also watch my Table Top Review Video for more details and info on this product!
I will also be following up my Table Top video with a Field Test Shooting Video to see what possible advantages and disadvantages the Air Venturi 3000 PSI with Stock & Adapter Aluminum Tank has in a real world test of its performance, hopefully all advantages!
Pros:
Compact and is the perfect size to use as a rear buttstock for various 88 Gram and or HPA rifles.
Smaller tank means if you are using a foot pump it won’t take all day to fill up :)
Comes with adapter so can be used with regular HPA and 88 Gram CO2 systems.
Regulated to 1100 psi so should perform better in terms of max velocity and consistency compared to CO2 which is around max 800-900 psi with velocity being effected by cool down.
Not effected by colder temperatures compared to CO2.
Once you have this tank the cost is virtually nothing to shoot compared to expensive 88 Gram CO2 cartages. You just need to buy your pellets or BB’s.
Cons:
Still takes a while to pump up using a foot pump system.
Higher initial cost ($195) than simply buying 88 gram CO2 cartages when you need them.
Will need access to a pump or compressor to use it.
Doesn’t look as good as the supplied buttstock at least with the Sig Sauer MCX and MPX.
Comments:
I guess the question is who is this for? If you are a casual shooter that perhaps owns the Sig MPX or MCX or even another 88 Gram CO2 Air Rifle that the Air Venturi 3000 PSI with Stock & Adapter Aluminum Tank would work with then this may be a bit expensive especially if you don’t have a way to pressurizer the tank at home. On the other hand if you already have a foot pump or air compressor or easy access to one and maybe you have other HPA or CO2 based airguns this tank will work with then it’s kind a no brainer to get it. Maybe you juts want a system that gives you maximum and consistent velocity no matter how cold it is outside. All good reasons to get one in my books.
In this Update Preview Unboxing Video I take a look at 5 products that came across my table and that I have not reviewed so far on the Replica Airguns YouTube channel.
First I show off an HPA tank from Air Venturi that works perfectly for the Sig Sauer MPX and MCX Pellet Rifles allowing for more consistent fps and I would image a higher overall fps? We will find out when I test it out in the replica Airguns Indoor Sea Can Airgun Range.
13 Oz Aluminum
10 Inches Long
2 Inches Diameter
Integrated Pressure Gauge
Includes Buttstock
CO2 Adaptor Included
3000 PSI Fill
1100 PSI Regulated
Next I take a look at the KJWorks M9A1 GBB Airsoft Pistol, I hover revived the CO2 version before but this version comes with the Gas magazine rather than the CO2 mag for those that prefer gas operated Blowback Airsoft Pistols. Because of the slightly lower FPS the Gas version comes with a barrel extension to make it Canada import friendly.
6mm Airsoft BB’s
Green Gas / Propane
370 fps
25 Round Magazine
2 Pounds
Probably one of the most interesting product I look at in this video at least for me is the EMG JW3 Combat Master GBB Airsoft Pistol. This Airsoft pistol is mainly aluminum with some polymer based off of the 2011 STI and was featured in the 2019 John Wick 3 Film. I’m really looking forward to testing this one out in the Sea Can Replica Airguns Airgun Range!
6mm Airsoft BB’s
Green Gas / Propane
9.4 Inches
366 fps
28 Round Magazine
2.4 Pounds
Moving along to another Air Pistol I finally get my hands on the Crosman P1 which is really just a KWC PT92 4.5mm Blowback CO2 BB Pistol but with Crosman Branding and an included laser. Since I have never shot a PT92 BB Pistol with a laser I will probably make a Field Test Shooting Video to see how well it performs.
4.5 mm Steel BB’s
CO2 x 1
4.2 Inch Barrel
330 fps
19 Round Magazine
2.4 Pounds
Comes with Laser Sight
Last up I take a look at the ASG TAC-6 which is pretty much the exact same ASG TAC-4.5 CO2 Air Rifle I tested a while back but in this case the 6 refers to it being a 6mm Airsoft Rifle rather than a 4.5mm Steel BB Riffle. I am not sure I will do a full Table Top Video since these guns are virtually identical but just in different Ammo types but I hope to get outside and see how well it performs shooting at a bit more distance than the 30 foot indoor range I usually test my Airgun in.
I have been wanting to test out the Crosman Full Auto Quick Reload Magazine for a while now and finally got around to it. The weather was cooperating with me so I went outside for this one and setup a bunch of cameras to make the many many magazine reloads a bit more interesting for my viewers.
The Crosman Full Auto Quick Reload Magazine has a hopper that is said to hold around 300 4.5mm Steel BB’s which I can attest it does in fact hold at least 300 BB’s. The Crosman Full Auto Quick Reload Magazine like their regular Crosman Full Auto Magazines holds two 12 gram CO2 Cartridges, so the question is, will I be able to get through most of the 300 BB’s without reloading the CO2?
Watch my struggle a bit to figure out the exactly how to properly use the Crosman Full Auto Quick Reload Magazine and then quickly eat through 300 or so BB’s blasting pop cans down range!
