Getting back to the Umarex IWI Tavor 21 Elite AEG Airsoft Rifle, how did it perform? I placed 5 rounds through my Chrony Chronograph using .20 gram plastic Airsoft BB's and it shot a pretty quick 425 fps! Not sure if I would want to use the Umarex IWI Tavor 21 Elite AEG Airsoft Rifle in any close quarters games with that velocity but it would perform well on a field and even get a round out to a nice distance.
Next I tested out the accuracy of the Umarex IWI Tavor 21 Elite AEG Airsoft Rifle as best I could in my kind of "cramped for rifles" indoor Sea Can Airguns Range. I place my paper target 30 feet down range and put 10 rounds in semi auto into the target shooting from a rested seated position with a sandbag up front for stability. The Umarex IWI Tavor 21 Elite AEG Airsoft Rifle shot a nice tight 1.5 inch grouping just a tad low and to the left but pretty close to the bulls-eye for being straight out of the box with no adjustments on my part.
In full auto mode the Umarex IWI Tavor 21 Elite AEG Airsoft Rifle performedas expected emptying the magazine making a clean 3 inch hole in my paper target with only a few of the 6mm Airsoft BB's venturing outside of it.
All in all the Umarex IWI Tavor 21 Elite AEG Airsoft Rifle is a nice performer with a good solid build quality and modern Bull-pup design. I really liked the pop-up sights and the fact that can use any standard AEG AR/M4 High capacity magazine with it.
In this yet another AEG Airsoft Field Test Shooting Video Review I mainly focus on the Cybergun Famas AEG Bullpup Airsoft Rifle and put it through my typical velocity and accuracy tests I conduct in the Replica Airguns Indoor Sea Can Shooting Range. I also show some other similar Bullpup styled AEG Airsoft Rifles in comparison that I plan on also reviewing very soon, the IWI Tavor 21 Elite Force and two AEG Bullpups from ASG, the Steyr Aug A2 and Steyr Aug A3 Proline Series..
So how did the Cybergun Famas AEG Bullpup Airsoft Rifle perform? I placed 5 rounds through my Chrony Chronograph using .20 gram plastic Airsoft BB's and I got right around a 360 fps average which is should be just about right for most indoor or outdoor shooting environments. Velocity consistency was also good.
Moving on to the accuracy portion of my indoor sea can field test, I place my paper target 30 feet down range and put 10 rounds into the target shooting from a rested seated position with a sandbag up front for stability. The Cybergun Famas AEG Bullpup Airsoft Rifle shot a nice 1.5 to 2 inch grouping just a little high but well centered. The front and back sigh are both adjustable making windage and elevation corrections very easy to do. You could also play around with the hop-up to adjust elevation at various ranges.
In full auto mode the Cybergun Famas AEG Bullpup Airsoft Rifle performed really well, I pretty much empty the magazine and the grouping only spread out to about 3 inches making a clean 3 inch hole in my paper target. There is something very gratifying about unloading an entree magazine in full auto and checking out the damage it caused :)
All in all the Cybergun Famas AEG Bullpup Airsoft Rifle is a great performer at a pretty low price tag of around $200 Canadian at the time of this review. If you want a slightly higher quality version than also checkout the Cybergun Famas F1 EVO Version which is only about $90 more and but offers better build material and and internals improvements.
In this Field Test Shooting Video Review I mainly focus on the ASG CAA M4 Sportline AEG Airsoft Rifle and put it through my typical velocity and accuracy tests I conduct in the Replica Airguns Sea Can Shooting Range. I do compare the ASG CAA M4 Proline AEG Airsoft Rifle to the ASG CAA M4 Sportline version since they look virtually identical but do have some notable differences, like the build materials and much lower cost for the ASG CAA M4 Sportline AEG Airsoft Rifle. That said both ASG CAA M4 AEG Airsoft Rifles did perform very similarly other than a bit of a velocity bump with the ASG CAA M4 Proline model over the Sportline I test in this video.
So how did the ASG CAA M4 Sportline AEG Airsoft Rifle perform? I placed 5 rounds through my Chrony Chronograph using .20 gram plastic Airsoft BB's and I got a 335 average fps which is a bit lower than the ASG CAA M4 Proline AEG Airsoft Rifle but still great for a variety of Airsoft shooting situations. I did notice that the FPS seemed to be creeping up slowly as I tested it, maybe some break in was taking place?
Moving on to the accuracy portion of my indoor field test, I place my paper target 30 feet down range and put 10 rounds into the target shooting from a rested seated position with a sandbag up front. The ASG CAA M4 Sportline AEG Airsoft Rifle shot a nice 1.5 to 2 inch grouping a little to the right of the bulls-eye and slightly low, which I can easily correct using the adjustable sights and hop-up adjustments. I like to conduct my field tests with all the guns right out of the box and with no adjustments prior to my testing since that's the way you're going to get them and you may have to also make some small correction to the sights and or hop-up adjustments.
In full auto mode the ASG CAA M4 Sportline AEG Airsoft Rifle didn't miss a beat. I emptied what was left of the mag (About 130 rounds or so) in no time with a few quick bursts making a nice mess of the paper target which is the result I'm looking for in full auto mode :)
In this Field Test Shooting Video Review I mainly focus on the ASG CAA M4 Proline AEG Airsoft Rifle and put it through my typical velocity and accuracy tests I conduct in the Replica Airguns Sea Can Shooting Range. I do compare the ASG CAA M4 Proline AEG Airsoft Rifle to the ASG CAA M4 Sportline version since they look virtually identical but do have some notable differences, like the build materials and perhaps a few internal upgrades found in the Proline version. That said both ASG CAA M4 AEG Airsoft Rifles did perform rather similarly other than a bit of a velocity bump with the ASG CAA M4 Proline model.
So how did the ASG CAA M4 Proline AEG Airsoft Rifle perform? I placed 5 rounds through my Chrony Chronograph using .20 gram plastic Airsoft BB's and I got a very respectable 392 average fps with most of the five shots actually getting 392 fps so very consistent velocity for sure.
Moving on to the accuracy portion of my indoor field test, I place my paper target 30 feet down range and put 10 rounds into the target shooting from a rested seated position with a sandbag up front. The ASG CAA M4 Proline AEG Airsoft Rifle shot a tight 1.5 inch grouping just to the right of the bullseye which I can easily correct using the adjustable sights. I like to conduct my field tests with all the guns right out of the box and with no adjustments prior to my testing since that's the way you're going to get them and you may have to also make some small correction to the sights and or hop-up adjustments.
In full auto mode the ASG CAA M4 Proline AEG Airsoft Rifle didn't miss a beat. I emptied what was left of the mag (About 200 rounds or so) in no time at all and made a nice mess of the paper target which is what I am usually going for :)
All in all the ASG CAA M4 Proline AEG Airsoft Rifle is a very high quality Airsoft gun but does come at a premium pricetag. If you're budget is a bit lower than checkout my upcoming Field Test Shooting Video of the more economical ASG CAA M4 Sportily AEG Airsoft Rifle which will be out this week.
This Black Friday weekend save 10% on everything in our Canada and US Online Replica Airguns Stores! It's already begun and ends Monday night so don't wait too long...
Type: Airsoft AR, M4, M16 Styled Rifle. Manufacturer:G&G. Model:ARP-556 and ARP-9. Materials: Metal and plastic/polymer construction. Weight: (ARP-9 4.4 pounds) (ARP-556 5.3 pounds). Barrel: 6 inches, metal non-rifled. Propulsion: AEG non-blowback. Action: Semi & full auto SAO. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: (ARP-9 300) (ARP-556 450). FPS: 400+.
Trigger Pull: The trigger pull on the G&G ARP rifles is an electric mechanical trigger that simulates a single action only trigger. There is essentially a light spring internally which supplies the trigger pressure. Pressure is even and smooth.
Build Quality: As with all of the G&G product line the G&G ARP-556 and ARP-9 AEG Airsoft CQB Rifles are really well made. Fit and finish is flawless and I had no issues shooting these guns at all. Every engagement of the trigger resulted in an Airsoft BB downrange and in full auto mode BB's where literally streaming from the barrel :) You will find a little more metal specifically in the receiver for the G&G ARP-556 over the G&G ARP-9 AEG Airsoft CQB Rifle which does make the ARP-556 a little bit heavier but not by much.
Realism: Both the G&G ARP-556 and ARP-9 AEG Airsoft CQB Rifles are super realistic, they are based on the AR, M4, M16 Rifle design but are scaled down for tactical close quarters use with their compact barrels and adjustable stocks. Most parts work as you would find on a real steel M4 like the charging handle, dust cover, simulated forward assist and of course the magazine releases. There is however no blowback operation but I can attest that if you have an 11.2 volt battery and are shooting in full auto you will feel this gun a rock'n.
2 lower and higher priced models with similar looks and performance to choose from.
Super compact CQB rifles.
Fully adjustable pop-up iron sights front and back.
Crown flash hider acts as a sound amplifier if you’re into that sort of thing?
Great internals, Internally upgraded with an ETU and MOSFET system.
Skeltonized PDW stock perfect for close quarters combat.
Nice 400 feet per second velocity, good for close and even further out ranges.
Very accurate, one of the best Airsoft rifles tested to date.
ARP-526 has an ambidextrous selector / safety switch.
ARP-556 has full metal receiver.
ARP-9 is a bit lighter and less tiring to carry, great if you plan to add on a bunch of accessories.
Cons:
No blowback operation.
ARP-9 has a plastic receiver.
You need some pretty compact batteries to fit into the short bumper tube.
Comments:
I am going to go on the record and say that the G&G ARP-556 and ARP-9 AEG Airsoft CQB Rifles would be my go to Airsoft battle rifle of choice. They have enough power for out door shooting and not too much for indoor shooting. Their compact and lightweight design will make them super easy to carry around all day and quick to place on any target in a hurry. Accuracy is not a concern since these AEG Airsoft Rifles can cut a bullseye out of a paper target no problem. Price for what you get, quality, looks. performance are all top notch with either choice of G&G ARP-556 or ARP-9 AEG Airsoft CQB Rifle you decide to go with.
My Vimeo Video Review for the G&G ARP-556 and ARP-9 AEG Airsoft CQB Rifles:
It's been a rather long time since I made an Airsoft Rifle Field Shooting Test video. I like to shoot a bit further out than 30 feet when using a rifle. Unfortunately the weather outside is getting really cold where I live so my testing will have to all be done inside the Replica Airguns Sea Can Airgun Range which only allows for about 30 feet worth of distance to my paper target. I figure if I can get a tight group at 30 feet than it shouldn't spread out too much at longer ranges!
Since the G&G ARP-9 and G&G ARP-556 have identical internals and similar barrel lengths I figured I only really needed to test one of them out so I picked the G&G ARP-556 AEG Airsoft CQB and put 5 shots through my Chrony Chronograph to get my Field Test Started. The G&G ARP-556 AEG Airsoft CQB shot a nice consistent 400 fps which is as high as I would want to go for indoor CQB type shooting. The BB's sure did get to my paper target quickly!
I followed my velocity testing with an accuracy test at 30 feet back using a rested shooting position, sand bag up front and sitting in the back. I first placed 10 rounds on my paper target in semi-auto and hit the 1.5 inch bullseye with every shot! I think this may have been a first for me using an Airsoft rifle? Of course I had to switch the G&G ARP-556 AEG Airsoft CQB over to full auto and see how she would perform. Since I was using an 11.2 volt bolt battery the rate of fire was crazy fast but even so in full-auto the bulk of the shots still hit the center bullseye cutting out a 2 inch hole in my paper target. The G&G ARP-556 AEG Airsoft CQB is a beast that I would not want to be on the receiving end of!
I'm pretty sure I found my go to AEG M4 styled CQB rifle, I'm not sure how you could beat the results I got shooting the G&G ARP-556 AEG Airsoft CQB. And if you're looking for a slightly lighter and less expensive version with the same performance then take a look at the G&G ARP-9 AEG Airsoft CQB.
I just received some really nice G& G Airsoft guns to share with everyone, I have two CQB Styled AEG rifles and a fantastic Gas Blowback Beretta Mod. 92FS.
The AEG CQB AR or M4 styled rifles are similar in a lot of ways and are super compact and really well built. The G&G ARP-9 has a polymer receiver and hand guard while the G&G ARP-556 has a full metal receiver and hand guard. Both have good weight to them. You will also find Skeletonized PDW stocks and large crown flash hiders on both models along with M-LOK hand guards. Inside you will find upgraded ETU and MOSFET electronics.
Obvious difference are the 9mm style magazine found on the G&G ARP-9 versus the M4 styled high capacity magazine on the G&G ARP-556. You also get an ambidextrous safety sector switch on the G&G ARP-556.
Next I show off the G&G GPM92 Beretta Mod. 92FS Gas Blowback Airsoft Pistol. It comes in a high quality hard plastic case with a well made speed loader. If you place the magazine in the gun you will have room for two magazine in the hard shell case. The G&G GPM92 hold 27 roads in it's double stack magazine that has some interesting new features that help it perform much beet in cold environments and really boost green gas usage. G& G calls them the Whirl Cylinder Valve system and Micro gas filter. Both help eliminate free up in the gun when shooting fast.
The G&G GPM92 Beretta Mod. 92FS is really well made and shoot in double and single action and the safety even works as a decocker. For those looking to add a mock suppressor you will happy to know the G&G GPM92 has a threaded barrel tip.
This weekend save up to 10% on BB, pellet and airsoft rifles!
Also, loyal blog and channel followers get a coupon code for FREE SHIPPING on their purchase. Now that's something to be thankful for! Read this post for details!
Well the Shipping Container Office and Airgun Shooting Range is finally all ready to use and so for this first ever airguns shooting video in it, I simply wanted to try out a couple of airguns and see how this new setup worked. I also wanted to play around with some camera position setup to see how it all looked and if there will be any additional lighting or placement considerations.
Summer is here! While some folks are working on a tan, you're out working on your aim. This weekend, stock up on all the essentials — ammo, CO2, targets, extra mags — so you can shoot until the sun goes down.
When you spend $50 or more on any items, we'll ship them to you for free! Ends Monday, so don't wait.
I got a lot done this week in the Shipping Container Project Office and Airgun Shooting Range. Finished up all the drywall office mudding, I primed and painted the the office, connected up all the electrical and office lighting and installed the hardwood and baseboard along with the trimming. All that's left in the office is some caulking, paint touchup and then I have to figure out how I'm going to finish up the shooting hole? I do have some ideas for it though...
Next week I will be working on these odds and ends and hopefully may even get the shooting range spray foam insulted?
About three weeks ago I started the interior construction of the Shipping Container Project. So far I have cut out the window and door, framed the office in, installed the window and door, done some preliminary painting, wired in electricity for the entire unit, added an internet line, run underground wiring to the main house, installed insulation and vapor barrier and last but not least, added the drywall. I would have to say the worst is over and now I look forward to more of the finishing work like painting, flooring, connecting the electrical plugs and lighting fixtures.
The only real big jobs left to do would be painting the outside of the Sea Can and spray foam insulating the shooting range area but the spray foaming I will be contracting out and getting it done professionally so that part will be easy at least!
Yup, another Shipping Container Project Update Video! For those of you interested in this project I am sure you have been waiting with baited breath ;) And for those wanting more airgun videos you are probably wondering when I will resume making more... Heck, I'm with you on that one, this manual labour stuff is way harder than making airgun videos, but it is all for the greater good. I will try and slip in some airgun related videos before this Shipping Container Project is finished, that's almost a promise!!!
At this point I am almost ready for drywall, all the electrical is completed including running the power and Internetunderground to the poorhouse and main house. I need to have my Internets at full jam, that's a must!
This week I will be getting the electirfcal all hooked up to the main box, adding isulation and vapour barrier, some more window baar cleanup and painting and by end of the week I hope to have the drywall in place along with the taping and first layer of mud.
Oh yah, this video also includes a huge bonfire, every spring and fall we usually burn all the fallen branches and yard debris, everyone comes out and enjoys the huge fire :)
The Shipping Container Project is moving along nicely, this past week I finished up my office area framing, I also got the door and window cutout and installed! Next up on my list is cleaning up and painting the window bars so I can make the unit a bit more secure. I suppose I will have to do the same with the metal door since it is in dire need of a facelift. Once the doors and windows are all taken care of I will be moving on to the electrical and wiring. My goal is to get all of this done by end of week... The sooner I get this Shipping Container Project done the sooner I can get back to making even better and more consistent airgun videos in my new home.
This week I started framing in my new office and in this video I show the wall closest to the airgun range where the door and shooting opening are situated. I managed to frame the back wall in too. I also talk about how much time it takes even before you pick up a drill or hammer simply planning everything out and acquiring all the supplies required for a project like this. I have spent a ton of time researching what I need to make this Shipping Container Project into the vision I have for it. Spoiler alert, in my next video the framing is all done including the installation of my window and outside door, glad that part is over!
No need to hunt for deals this Easter, EVERYTHING in our store is on sale! So kickoff your long weekend with a long-barreled revolver. Celebrate spring’s arrival with a spring powered sniper rifle. Or treat yourself to a hollow chocolate bunny and some hollow point pellets. This deal ends soon, so hop to it!
Lately I have been doing a lot of sourcing out figuring out how everything is going to be laid out, what kind of lighting I want to use, how am I going to heat the office area in my shipping container. I want to keep everything pretty low power so my plan is to go with all LED lighting and a 400 Watt heater which should be
fine in my 90 square foot insulated office space. I plan to blast the shooting range with some propane heat on days when I need it for the shooting testing during the colder months.
I did pickup some hardwood flooring pretty cheap at Big Box Store and also got my 3x6 office window from Surrey New and Used. I already have metal doors that my father-in-law has had stashed away for several decades but at least now they are going to come in handy.
The first job or actual work I needed to do on the Shipping Container Project was to level and place the Sea Can onto some bricks/slabs, this also helps to keep the underside dry so it does not rust out. There shouldn't be much settling since the storage container is resting on my gravel parking area and the gravel goes right down about 1 foot deep to the hard pan.
Next on my list is starting the framing, figuring out exactly where the windows and doors will be and of course cutting the container to fit them.
This Vimeo video will be a little different than most, sorry no shooting and not even a single gun to show anywhere in this video! But it will lead to hopefully better shooting field test and table top videos down the road as I will have a dedicated space not only to work but to also shoot my review airguns.
Today, well actually yesterday a 40 foot shipping container (Sea Can) showed up at my house. This new metal box is going to be my airgun shooting range and office space combined. It will contain a 30 foot airgun shooting range closest to the rear doors so that I can open them and create a longer range if necessary. The front 10-12 feet of the container will be my work office space where. I will also use some of the container for storage.
Over the next few weeks I will be leveling the container, framing and insulating the office area, adding some electricity and lighting and of course completing some finishing work to the office space to make it more cozy. Eventually I hope to do some outside work giving the container some more curb appeal with a new coat of paint.
I plan to make more videos to share with everyone of the work progress as it happens so keep watching...
