Entries in Single Shot,GBB

G&G GPM92 Beretta Mod. 92FS GBB Airsoft Pistol Table Top Review

15 Comments

Type: Gas Blowback Airsoft Pistol.
Manufacturer:  G&G
Model: GPM92
Materials: Metal slide & frame.
Weight: 2.24 pounds (1016 grams).
Length: 8.9 inches total
Barrel: 4.6 inches, Metal non-rifled smooth bore.
Propulsion: Green gas or propane.
Action: Blowback, single and double action.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 27 rounds.
FPS: 350+ fps.

Trigger Pull: The trigger pull on the G&G GPM92 Beretta Mod. 92FS GBB Airsoft Pistol is very good in both single and double action. Double action is a bit longer but not that much heavier when shooting in single action. Single action shooting is short, light and crisp as you would expect when shooting a real steel Beretta 92 style pistol.

Accuracy: I have not done my actual Field Test Shooting video review for the G&G GPM92 Beretta Mod. 92FS GBB Airsoft Pistol but I did get the chance to shot it quickly in my Sea Can indoor shooting range. Blowback felt good and accuracy seemed tight even though I was shooting free hand. I did notice the G&G GPM92 Beretta Mod. 92FS GBB Airsoft Pistol shot just a little bit low but I can adjust the hop-up slightly to account for it.

Build Quality: Like pretty much all G&G Airsoft guns, the G&G GPM92 Beretta Mod. 92FS GBB Airsoft Pistol build quality is right inline. Fit and finish where excellent and a lot of attention to detail was seen all over this Replica Airsoft Pistol. There is also some new gas valve technology from G&G that should significantly help with freezing in colder or fast shooting situations.

Realism: The G&G GPM92 Beretta Mod. 92FS GBB Airsoft Pistol is an excellent replica of the real steel Beretta Mod. 92FS, the safety even acts as a working decocker. You'll also find 5, 10, and 15 numbered markings on the backside of the magazine that would normally indicate how many bullets are in the magazine, a nice touch for sure! Everything works pretty much the same as it would on a real Beretta M9 including the ability to fully field strip the G&G GPM92 Beretta Mod. 92FS GBB Airsoft Pistol.

Available in the: Replica Airguns Store

Pros:

  • Lots of metal and good overall weight.

  • Pretty heavy Blowback operation.

  • Whirl Cylinder Valve system should expect to get decent amounts of shots per gas fill.

  • White dot sights front and back.

  • Comes with hard shell case.

  • Very detailed full size drop out metal magazine.

  • 20mm rail for accessories.

  • Comes with high quality speed loader.

  • Safety also works as a decocker.

  • Threaded removable barrel tip for add on mock suppressor.

Cons:

  • Sights are non adjustable.

  • A little bit more expensive than some other Beretta M92 full blowback Airsoft pistols

  • Barrel opening not as recessed as much as a real 9mm would be.

Comments:

I would have to say the G&G GPM92 is one of the nicest Beretta Model 92FS Airsoft Pistols you are going to find out there. There is a ton of attention to detail for sure, You also get the hard shell case with included high quality speed loader and G&G's new Advanced Safety Release Valve and Revolutionary Whirl Cylinder Valve that help with freeze-up issues. You might pay just a smidgen more that some other similar Blowback Beretta M92's out there but I feel it is well worth it.

My Vimeo Table Top Review of the G&G GPM92 Beretta Mod. 92FS GBB Airsoft Pistol:

Categories: 6mm, Airsoft, Blowback, Gas, GBB, Pistol, Review, Semi Auto, YouTube Video Tags: Beretta, Beretta M9, Beretta M 92 FS, G&G, GPM92

G&G GPM92 - ARP 9 & ARP 556 Airsoft Gun Preview Video

No Comments

I just received some really nice G& G Airsoft guns to share with everyone, I have two CQB Styled AEG rifles and a fantastic Gas Blowback Beretta Mod. 92FS.

The AEG CQB AR or M4 styled rifles are similar in a lot of ways and are super compact and really well built. The G&G ARP-9 has a polymer receiver and hand guard while the G&G ARP-556 has a full metal receiver and hand guard. Both have good weight to them. You will also find Skeletonized PDW stocks and large crown flash hiders on both models along with M-LOK hand guards. Inside you will find upgraded ETU and MOSFET electronics.

Obvious difference are the 9mm style magazine found on the G&G ARP-9 versus the M4 styled high capacity magazine on the G&G ARP-556. You also get an ambidextrous safety sector switch on the G&G ARP-556.

Next I show off the G&G GPM92 Beretta Mod. 92FS Gas Blowback Airsoft Pistol. It comes in a high quality hard plastic case with a well made speed loader. If you place the magazine in the gun you will have room for two magazine in the hard shell case. The G&G GPM92 hold 27 roads in it's double stack magazine that has some interesting new features that help it perform much beet in cold environments and really boost green gas usage. G& G calls them the Whirl Cylinder Valve system and Micro gas filter. Both help eliminate free up in the gun when shooting fast.

The G&G GPM92 Beretta Mod. 92FS is really well made and shoot in double and single action and the safety even works as a decocker. For those looking to add a mock suppressor you will happy to know the G&G GPM92 has a threaded barrel tip.

Categories: 6mm, AEG, Airsoft, Blowback, Full Auto, Gas, GBB, Pistol, Rifle, Semi Auto, YouTube Video, Review Tags: G&G, Beretta M 92 FS, Beretta M9, GPM92, ARP-9, ARP-556, Beretta

Which Sig Sauer P226 Airgun is the Best?

No Comments

In this comparison video I look at a variety of different Sig Sauer P226 Airguns and compare them to each other to determine which one I feel is the best Sig Sauer styled Airgun. Of course my choice may not be your choice :) 

Some of the airguns I consider in this comparison video are the: Umarex HPP BB Pistol, the Sig Sauer P226 Pellet Pistol, the Cybergun/KWC X-Five BB Pistols in Standard and Sight Rail versions, the Cybergun KJWorks KP01 P226 Airsoft Pistol, and the KJWorks KP02 P229 Airsoft Pistol.

So which Sig Sauer P226 did I like the best? Make sure to watch my YouTube Video and find out!

Categories: 4.5mm / .177 cal, 6mm, Airsoft, BB, Blowback, CO2, Comparison, Gas, GBB, Pellet, Pistol, Review, Semi Auto, YouTube Video Tags: Sig Sauer P226, Sig Sauer P229., Sig Sauer

Umarex NXG APX Multi-pump Pellet-BB Rifle Table Top Review

1 Comment

Type: Multi-pump Pellet-BB rifle.
Manufacturer: Umarex USA.
Model: NXG APX.
Materials: Metal and polymer parts.
Weight: 3.4 pounds (1.54 kg).
Barrel: 20 inches, rifled.
Propulsion: Multi-pump.
Action: Single shot pellets/repeater BB's.
Ammunition Type: .177 caliber pellets & 4.5mm steel BB's.
Ammunition Capacity: 75 BB's in hopper.
FPS: up to 490.

Trigger Pull: The trigger pull on the Umarex NXG APX Multi-pump Pellet-BB Rifle is not too bad, I would not say it's overly light but not on the heavy side either. Essentially it has a single action trigger since you need to pre-charge the bolt to engage the trigger. There is a little bit of take-up and then a fairly noticeable break point where you will feel the most trigger weight right before it releases.

Accuracy: So far I have not performed my Field Test Shooting review for the Umarex NXG APX Multi-pump Pellet-BB Rifle so I do not have any velocity or accuracy information to share at this point. I do plan on making that Shooting video Review this week so stay posted for that one.

Build Quality: The Umarex NXG APX Multi-pump Pellet-BB Rifle is not going to be one of your highest quality airguns but it does get the job done and feels solid enough with all the working parts feeling tight and secure. Most of the Umarex NXG APX Multi-pump Pellet-BB Rifle is plastic, even the bolt and trigger but you will find more metal inside where it counts like the inner steel barrel and the outer steel barrel shroud. The stock is plastic and that's OK, I do like the addition of the rubber butt pad and cheek rest as they work well and help to make the Umarex Umarex NXG APX Multi-pump Pellet-BB Rifle feel comfortable to hold in position and shoot.

Realism: Since the Umarex NXG APX Multi-pump Pellet-BB Rifle is not a replica, realism is not really a factor here but it does look like a gun so treat it as if it was a real gun since most people will not know the difference. Always transport and store any airgun safely and discreetly.

Pros:

  • Low cost air rifle with a lot of features.

  • Iron sights actually look really usable with the fiber optic red dot up front.

  • Comes with an 4x15 optical sight which should help with accuracy at longer ranges.

  • Super easy to pump even when getting close to the 10 pump max.

  • Built in auto safety.

  • Stock and cheek rest position feel really good.

  • Choice of shooting pellets or BB’s.

  • Trigger feels pretty good, not too heavy.

  • Mostly an ambidextrous design so good for lefties too.

  • Has a rifled barrel.

  • Overall a good looking air rifle.

Cons:

  • Mostly plastic, not the highest quality build.

  • Included 4x15 scope is super low budget but will work till you can upgrade it down the road.

Comments:
I really hope the Umarex NXG APX Multi-pump Pellet-BB Rifle shoots well as it is kind of a cool air rifle with a lot of features at a low price tag and would make a great little target and maybe even small pest air rifle if it turns out to be accurate and hit that near 500 fps mark with pellets. The Umarex NXG APX Multi-pump Pellet-BB Rifle is not going to win any quality or design awards but from a usability stand point it works well and feels good to hold and shoot, the rear stock and cheek rest are in a perfect piston for me and this is a pretty small airgun overal. Personally I would invest in an upgraded scope, something like the Walther 4x32 would be perfect and not too expensive.

The Umarex NXG APX Multi-pump Pellet-BB Rifle is available in both the Stand Alone Air Rifle and Kit Version that comes with the addition of safety glasses, targets and ammo.

 
Categories: 4.5mm / .177 cal, BB, Multi-pump, Pellet, Repeater, Review, Rifle, Scope, Single Shot, YouTube Video Tags: Umarex, NXG APX

Ruger Explorer Youth Break Barrel Pellet Rifle Table Top Review

No Comments

Type: Break barrel pellet rifle.
Manufacturer: Umarex USA.
Model: Ruger Explorer.
Materials: Metal and polymer parts.
Weight: 4.45 pounds (2.5 kg).
Barrel: 12 inches, metal rifled.
Propulsion: Spring piston.
Action: Single shot.
Ammunition Type: .177 caliber pellets.
Ammunition Capacity: 1.
FPS: 495.

Trigger Pull: I found the Ruger Explorer Youth Break Barrel Pellet Rifle to have a fairly light trigger, there is some initial take up with a smooth almost undetectable break or release point, I found that as I shot the Ruger Explorer Youth Break Barrel Pellet Rifle the trigger seemed to be breaking in a bit which made it a bit hard to figure exactly when the trigger was going to release but I feel over time and once the Ruger Explorer Youth Break Barrel Pellet Rifle is broken in the trigger will become more predictable.

Accuracy: Since I have already made a shooting or field test video for the Ruger Explorer Youth Break Barrel Pellet Rifle, I can comment on its performance n this review! With 6 grain lead pellets (on the lighter side), I was able to get a 5 shot Chronograph average velocity of 485 fps. Using heavier 7-8 grain pellets the velocity slowed down a bit to around 400 fps. In terms of accuracy the Ruger Explorer Youth Break Barrel Pellet Rifle performed well getting about a 1 inch 10 shot grouping on my paper target setup 30 feet down range. I know the Ruger Explorer Youth Break Barrel Pellet Rifle can do better than this once the trigger settles down a bit since some shots went off unexpectedly.

Build Quality: The Ruger Explorer Youth Break Barrel Pellet Rifle is not an expensive air rifle and is more or less an entry level spring piston pellet shooter. That said it is built fairly well with a metal receiver, barrel and trigger setup. The modern looking stock is polymer and the steel barrel is coated in a synthetic soft plastic to help with long term durability. The real fiber optic sight is plastic so you will have to be careful with it as it does protrude a bit from the air rifle.

Realism: Since the Ruger Explorer Youth Break Barrel Pellet Rifle is not a replica realism is not really a factor here but it does look like a gun so treat it as if it was a real gun since most people will not know the difference. Always transport and store any airgun safely and discreetly.

Pros:

  • Really great looking air rifle with a modern look to it.

  • Finish is very durable with its polymer stock and plastic/rubber coated barrel.

  • Fully adjustable fiber optic sights are easy to sight in and use.

  • Receiver is notched for ring mounts so you can add an optical sight or red dot to it.

  • Trigger is fairly light, just need some break in time with it.

  • Cocking effort is fairly easy at 16.5 pounds.

  • Great size gun for all ages.

  • Power and accuracy were good for an entry level air rifle.

Cons:

  • I did find the trigger break/release point to be a bit unpredictable but I feel this is a break-in issue and will become more consistent over time.

  • You have to remember to push that safety in with ever shot.

Comments:
The Ruger Explorer Youth Break Barrel Pellet Rifle is marketed as a Youth air rifle but in reality it would be great fun for all ages. I am a fairly large person at 6 feet tall and I had no problem dealing with the slightly shorter configuration. The trigger guard is nice and open and allows for large fingers which is not always the case with airguns designed for smaller individuals. The overall quality you get with the Ruger Explorer Youth Break Barrel Pellet Rifle for the lower entry level price tag is very good and in terms of performance I feel you for sure get your monies worth with the Ruger Explorer Youth Break Barrel Pellet Rifle.

 
Categories: 4.5mm / .177 cal, Break Barrel, Pellet, Review, Rifle, Single Shot, Spring Piston, YouTube Video Tags: Ruger, Explorer, Ruger Explorer

Ruger Explorer Youth Break Barrel Pellet Rifle Shooting Review

1 Comment

I don't do a lot of Springer (Spring Piston) Air Rifle shooting tests or even reviews for that matter. Mainly for a couple of reasons: Number 1, my content is mostly focused around Replica style Airguns and Number 2, it's kind of hard to test out the longer range airguns in my 30 foot airgun range. That said I felt the Ruger Explorer Youth Break Barrel Pellet Rifle would be a really great airgun to review since it is both affordable and even though it is targeted for the youth market, it really does make a great shooter for all ages.

I have not done a Table Top Review for the Ruger Explorer Youth Break Barrel Pellet Rifle but plan to shortly so stay posted for more detailed info on the Ruger Explorer Youth Break Barrel Pellet Rifle down the road in that review.

Even at 30 feet out, shooting the Ruger Explorer Youth Break Barrel Pellet Rifle should give us an idea of the ballpark this gun is able to shoot within, I also only used the adjustable fiber optic open sights for this review but I would suggest a low powered optical Scope or even a Red Dot since the Ruger Explorer Youth Break Barrel Pellet Rifle is grooved for scope mounts.

So how'd we do during my Field Test Shooting Video for the Ruger Explorer Youth Break Barrel Pellet Rifle? Not bad I would say! Using about 6 grain rather light weight .177 caliber lead pellets I was able to get really close to the 500 fps claimed fps mark coming in just under at a 5 shot testing average of 485 fps. I did put a couple heavier grain pellets through my Chrony Chronograph and got closer to the 400 fps mark, still not bad for this lighter sprung spring piston air rifle.

In terms of accuracy, shooting at my paper target setup 30 feet down range in my Sea Can Airgun Range, I shot about a 1 inch 10 shot grouping. I was finding the trigger break-in to be a bit unpredictable during this testing which led to some premature shots going off so I do feel once the Ruger Explorer Youth Break Barrel Pellet Rifle is broken in and me getting use to the trigger break, I should be able to improve on this result.

Overall the Ruger Explorer Youth Break Barrel Pellet Rifle is a really nice entry level airgun perfect for all ages and not just the youth market. It looks really cool, is easy to cock and has a very resilient finish. Oh ya it shoots pretty good to!

 
Categories: 4.5mm / .177 cal, Break Barrel, Field Test, Pellet, Rifle, Review, Single Shot, Spring Piston, YouTube Video Tags: Ruger, Ruger Explorer, Explorer

Baikal MP-53M Break Barrel .177 Pellet Air Pistol Sea Can Shooting Review

1 Comment

Yet another retest for an airgun I have already reviewed. But some airguns need another "shot"! Today I just kind of felt like shooting a springer and the Baikal MP-53M Break Barrel .177 Pellet Air Pistol came to mind. I'm not the best at shooting spring pistons airguns since they take a more softer relaxed grip and I tend to hold guns with a bit of a firmer grip.

If you're interested you can watch my previous Field Test Shooting Video for the Baikal MP-53M I performed a couple years back outside on my deck.

As always in my new Sea Can Shipping Container I perform a Chronograph velocity test to see what the real world feet per second is and  then I perform a followup accuracy test shooting 10 rounds at a paper target 30 feet down range using a rested seated position. During the velocity Chrony test for the Baikal MP-53M Break Barrel .177 Pellet Air Pistol I was able to get an average of 405 fps which was much higher than my previous testing where I averaged 319 fps. I was using different 7 grain lead pellets but I don't think they where that much different in weigth since the Diabolo pellets should have been around 6-7 grain.

Moving onto the accuracy portion of my Field Test review, this time around my shots stayed a little tighter than last time stretching out to about 2 inches but most of the 10 shots where all within 1 to 1.5 inches. The trigger on the Baikal MP-53M Break Barrel .177 Pellet Air Pistol is really great, super light with just a little take-up and virtually a hair trigger after that with zero friction.

I also wanted to mention that cocking the Baikal MP-53M Break Barrel .177 Pellet Air Pistol is fairly easy and that I did find I needed to set the rear sigh to the all the way down position to get my shots to hit close to the bullseye as this gun seemed to like to shoot rather high out of the box.

 
Categories: 4.5mm / .177 cal, Field Test, Pellet, Pistol, Review, Single Shot, Spring Piston, YouTube Video Tags: Baikal, MP-53M

Gletcher M1891 Sawn Off Mosin Nagant Rifle CO2 BB Gun Sea Can Shooting Review

No Comments

A few years back I did a field test shooting review for the Gletcher M1891 Sawn Off Mosin Nagant Rifle CO2 BB Gun but rather than my standard rested 30 foot paper target test I got out into the yard a bit and shot at some clay targets setup at a variety of ranges. I did this shooting freehand and unrested so the accuracy was a little left to be desired and actually determining how accurate the Gletcher M1891 Sawn Off Mosin Nagant Rifle CO2 BB Gun was.

So I decided to revisit the Gletcher M1891 Sawn Off Mosin Nagant Rifle CO2 BB Gun and retest the accuracy in my new Sea Can using paper targets setup 30 feet away using a rested and lated shooting position. I also redid my Chronograph velocity test siren my new Chromo setup is working so well.

I did get very similar results with my velocity Chromo Test, my first test I averaged about 430 fps and this time I got 428 fps shooting a 5 shot string. Moving onto the accuracy potion of my Field Test Shooting Review for the Gletcher M1891 Sawn Off Mosin Nagant Rifle CO2 BB Gun, I did notice that it was shooting a little bit to the left, elevation was bang on but unfortunately with the Gletcher M1891 Sawn Off Mosin Nagant Rifle CO2 BB Gun you can only adjust elevation and not windage?

Even so I was able to get about a 1.5 inch grouping with 10 shots on target with the Gletcher M1891 Sawn Off Mosin Nagant Rifle CO2 BB Gun. But there was one mystery shot that seemed to for sure hit the target but left no indication of where it hit, perhaps I hit the same hole as my first shot?

The Gletcher M1891 Sawn Off Mosin Nagant Rifle CO2 BB Gun is a really cool rifle, I would love to test out the Gletcher M1944 longer version but so far I have not been able to get my hands on one and have only seen it so far at SHOT Show. Keep checking our Replica Airguns online stereo for stock as our Gletcher inventory does go in and out of stock at times.

 
Categories: 4.5mm / .177 cal, BB, CO2, Field Test, Pistol, Review, Rifle, Single Shot, YouTube Video Tags: Gletcher, M1891, Mosin Nagant

Umarex DX-17 Spring Powered BB Pistol Field Test Review

3 Comments

I was a bit surprised by the Umarex DX-17 Spring Powered BB Pistol, it actually shot a lot better than I was expecting it to perform. I did have to aim rather low since the Umarex DX-17  BB Pistol likes to shoot on the high side but if you are shooting at closer in ranges then you won't have to adjust your aim point so high.

Getting into my performance testing for the Umarex DX-17 Spring Powered BB Pistol, I placed 5 shots through my Chrony Chronograph and averaged 210 fps which again was very close to the Umarex claimed 200 fps, even a little bit higher! he DX-17 is a single shot repeater but because of the BB reservoir you can quickly reload follow up shots by simply point the Umarex DX-17 Spring Powered BB Pistol a little upward while pulling the slide back and pushing it forward to active the spring piston and load a BB at the same time.

As I mentioned the Umarex DX-17 Spring Powered BB Pistol shot on the high side, at 30 feet it's a good 8-9 inches high but I have a feeling that this is about as high as the BB's will rise since they are not going that fast and gravity will start bringing them back down. At about 10-15 feet out from a target the Umarex DX-17 Spring Powered BB Pistol seemed to shoot about 3-4 inches high so not nearly as bad and this can be adjusted pretty easy by simply aiming a bit under the target you are shooting at. In terms of a 10 shot grouping theUmarex DX-17 Spring Powered BB Pistol got about a 4 inch grouping which I have to say kind of surprised me as I was expecting a much larger spread.

So for about $20 you kind of get what you pay for but I really think with the Umarex DX-17 Spring Powered BB Pistol you perhaps get a little more! It has a really good trigger, seemed to be built pretty tuff, shot exactly right on the claimed fps mark and was even able to keep a reasonable grouping. And to keep costs down even more you never need to buy CO2 so that's another bonus.

 
Categories: 4.5mm / .177 cal, BB, Break Barrel, Field Test, Pistol, Repeater, Review, Single Shot, Spring Piston, YouTube Video Tags: Umarex, DX-17

Umarex DX-17 Spring Powered BB Pistol Table Top Review

No Comments

Type: BB air pistol.
Distributer: Umarex.
Model: DX-17.
Materials: Mostly plastic build.
Weight: 1.6 pounds (726 grams).
Barrel: 4.27 inches, non-rifled.
Propulsion: Spring.
Action: Single shot.
Ammunition Type: 4.5mm Steel BB's.
Ammunition Capacity: 15 round BB reservoir.
FPS: 200.

Trigger Pull: The single action only trigger pull on the Umarex DX-17 Spring Powered BB Pistol is actually pretty good. It's fairly short with only a little bit of very light take up and then an easy release that has no added friction. So you will have to get use to when and where the release happens but it is a really decent trigger for such an inexpensive airgun.

Accuracy: I have only shot the Umarex DX-17 Spring Powered BB Pistol a few times to get use to the mechanical operation of using this spring powered pistol since there is a very specific order in which you need to cock and load the Umarex DX-17 for proper operation. I did find the DX-17 shot a bit high for me at 30 feet out so I had to adjust my aim point about 5-6 inches lower to hit targets at this range. For further out shooting you many not need to do so since the fps is fairly low and I would expect the BB to drop pretty quickly. In terms of power being that the Umarex DX-17 Spring Powered BB Pistol is only rated at 200fps, well it seems sufficient enough for plinking away at targets and should have no problem getting through a pop can.

Build Quality: I was expecting this $20 low cost BB airgun to be fairly low quality in general but when I took it out of the plastic clamshell packaging I was pleasantly surprised by the overall quality and how the Umarex DX-17 Spring Powered BB Pistol felt in my hand. It has a good weight to it and the fit and finish are really good. Mechanical parts tolerances feel snug and the plastic used feels of good quality.

Realism: The Umarex DX-17 Spring Powered BB Pistol as far as I know is not a replica of any specific real steel gun in production but it does kind of remind me of a Browning Hi-power at least the back half and the way the frame angles up a bit in front of the trigger. Other than that it looks the part of a real gun. The DX-17 has what looks like real working parts on it with the slide catch, magazine release and magazine but plat all moulded into the airgun.
Available at the: Replica Airguns Store

Pros:

  • At $21 Canadian its great value for a target plinker.

  • It actually looks and feels pretty good in person, better than I expected build quality and weight to it.

  • No CO2 required so very cheap to shoot.

  • Single action trigger is actually really decent, better than most airguns.

  • Accessory rail for adding a red dot or perhaps a tactical light.

  • 15 round reservoir makes followup shots quicker and no fumbling around loading BB’s in-between shots.

  • Lower fps means if you do do something stupid you are less likely to have to make a trip to the doctor

Cons:

  • Pretty low fps so don’t expect any long range shooting or great penetration.

  • Sights are not adjustable and it seems to shoot kind of high.

  • Why not rifle the barrel and make pellets an option?

Comments:

I rarely review these super low cost airguns especially spring powered ones with low fps, it almost seems like why would you want any of that? But you know the Umarex DX-17 Spring Powered BB Pistol is actually a great little airgun and you really can't beat the price tag. You are also going to save a bunch of money not having to buy CO2 and once you load 15 rounds into the BB reservoir you can empty the DX-17 fairly quickly. Sure the power seems a bit low but it gets the job done and like I said if there was an accident, you are less likely to break that window or require medical attention. I think this would be a great add on to an existing order you might be making with us, that way you wouldn't have to pay for shipping for this one item and you get a fun little plinker for only $20 more.

My Vimeo Videos for the Umarex DX-17 Spring Powered BB Pistol:

 
Categories: 4.5mm / .177 cal, BB, Break Barrel, Pistol, Review, Single Shot, Spring Piston, YouTube Video Tags: Umarex, DX-17

Cybergun KWC Colt 1911 Rail Gun M45 A1 CO2 Blowback BB Pistol Shooting Review

No Comments

Another Airgun Shipping Container (Sea Can) Shooting video and for this indoor filed test I put the KWC - Cybergun M45A1 1911 CO2 Blowback Airsoft Pistol through its paces.

What I am super happy about is that my Chrony Chronograph seems to be working really well as I tested a pellet, steel BB and Airsoft pistol out today and every single round through my Chrony got a reading :)

Now back to the Field Test Shooting Review at hand... I started off by placing 5 shots through my Chrony Chronograph using a brand new CO2 with .20 gram Airsoft BB's and got a really consistent reading for all 5 shots with an average of 357. The lowest shot was 353 and the fastest shot was 364 so all shots where really close in velocity. The container temperature was a near perfect shooting temperature of 23 degrees Celsius which was ideal for optimal CO2 velocity testing.

During my accuracy portion of this Field Shooting Test. I used my new seated in the back and sand bag rested up front shooting position which is about 30 feet back from my paper target. I did notice during my Chrony testing that the Cybergun KWC Colt 1911 Rail Gun M45 A1 CO2 Blowback BB Pistol liked to shoot a bit high, perhaps the hop-up needs a bit of twerking? So for my accuracy testing I shot at the bottom ring of the target, this helped me get more shots on the paper for sure but the Airsoft BB's still moved around a bit vertically. I was able to get about a 4-5 inch 10 shot grouping which is totally acceptable for a close range Airsoft sidearm and in an Airsoft battle I would think even shooting at about 50 feet or so I could easily hit a persons mid section consistently.

The Cybergun KWC Colt 1911 Rail Gun M45 A1 CO2 Blowback BB Pistol has a ton of blowback kick to it and a super nice single action trigger like all the KWC 1911's The modern Tactical coloration and trimmings makes this pistol a great choice as a present day side arm. It's real looker for sure with performance to match!

 
Categories: 6mm, Airsoft, Blowback, CO2, Field Test, GBB, Pistol, Review, Semi Auto, YouTube Video Tags: KWC, Cybergun, M1911, M45A1, Colt

Crosman American Classic P1322 22 Caliber Pellet Pistol Table Top Review

No Comments

Type: Pellet Air Pistol.

Manufacturer: Crosman.

Model: P1322 American Classic.

Materials: Metal & plastic.

Weight: 2 pounds.

Barrel: 10.25 inches, metal rifled.

Propulsion: Multi-pump pneumatic, up to 10 pumps.

Action: Bolt-action single shot, single action only.

Ammunition Type: .22 caliber pellets.

Ammunition Capacity: 1 round.

FPS: 460.

Trigger Pull: The trigger pull on the Crosman American Classic P1322 22 Caliber Pellet Pistol is non-adjustable but is short and fairly light with virtually no creep at all, it's just right there! The Crosman American Classic P1322 will allow for very accurate shot placement with only a little trigger time required to get use to the release tension required.

Accuracy: I found my Original Crosman 1377 (The .177 caliber version of this airgun) to be an amazing target pistol, getting about a 1/2 inch grouping from 30 feet out in a semi-rested position. And I even performed my accuracy test twice with the same result each time. In terms of fps performance, the Crosman American Classic P1322 22 Caliber Pellet Pistol is not required to be detuned for Canada importation so we should see very close to 460 fps even using heavier grain lead pellets! Make sure to look for my upcoming Field Test Shooting video for the Crosman American Classic P1322 22 Caliber Pellet Pistol.

Build Quality: The Crosman American Classic P1322 22 Caliber Pellet Pistol is not a fancy looking airgun but it gets the job done with a mostly all metal design and build. Remember this Croman configuration has been around since 1977 so about  40 years and has pretty much stayed the same so Crosman must be doing something right with the American Classic series if it has stood the test of time with very few changes to its design other than some cosmetics ones.

Realism: The Crosman P1322 American Classic Air Pistol is not a replica of any gun out there. The P1322 is made as a target airgun, so it looks like a target air pistol and is not expected to resemble a tradition real steel pistol of any sort.

Pros:

  • Fairly inexpensive target pistol (under $100 Canadian - $79 US)

  • Know to be very accurate.

  • Ability to regulate power with the amount of pumps.

  • Mostly all metal construction.

  • Rifled steel barrel.

  • Adjustable rear sight.

  • Light single action trigger.

  • Would be good for small close shot pest control because of good FPS and good accuracy for shot placement ability.

  • Lots of mods and upgrades available for this series of Crosman Airguns.

Cons:

  • The trigger is a bit thin (Can be upgraded).

  • Rear sight is adjustable but is hard to setup.

  • All black sights are hard to aim on darker targets.

  • Pumping is fairly firm and will take some time for max 10 pump power.

Comments:

The Crosman American Classic P1322 22 Caliber Pellet Pistol is a bit of a sleeper target pistol. It has been around for a long time and for this reason can be overlooked. It also is a super flashy looking airgun that requires a bit of manual pumping to get to maximum power. There is also the kind of finicky sight setup required to get this air pistol to shoot on target. If you can put all that aside you have yourself a super accurate and rather powerful little target or even small pest control airgun for a lot less money than some other pellet target pistols out there. And to be honest I would trade having to pump this gun up over a springer for the main reason that the recoil is so much less violent on a pump gun allowing for better accuracy at the end of the day. When you factor in all the mods that are available for this line of Crosman Airguns the sky is the limit allowing for a ton of customization in performance and looks.

My Vimeo Video Review of the Crosman P1322 American Classic .22 Caliber Target Pistol:

Categories: .22 cal, Multi-pump, Pellet, Pistol, Review, Single Shot, YouTube Video Tags: Crosman, P1322

Crosman PFAM98 Taurus PT-92 and American Classic P1322 Airgun Overview

1 Comment

First off, I want to thank Crosman for providing these two guns for review! Now they're not exactly new guns by any means but for sure worth showing and doing some update reviews for.

Starting with the Crosman PFAM98 Taurus PT-92:

The Crosman PFAM98 Taurus PT-92 is essential a KWC made M92 also branded as the same gun as the Cybergun GSG 92 and the Swiss Arms P92.

So for all intense and purposes if you have watched any of my other revise on this line of KWC Beretta /Taurus BB pistols and even Airsoft versions then this BB gun should be really familiar to you.

History of the Taurus PT-92:

It is often referred to as a Berate 92 copy but in fact it is a Taurus PT-92 replica. The Taurus PT-92 is a product of Brazil, Taurus actually bought the entire Brazilian Beretta factory back in 1980 including drawings, tooling, machinery, and a very experienced work force to make the guns. Taurusimmediately sought to improve on the Beretta design, resulting in the popular and acclaimed Taurus PT-92.

Specifications for the Crosman PFAM98 Taurus PT-92:

  • Full Blowback operation.

  • Full metal frame, slide and magazine.

  • 12 gram CO2.

  • 4.5mm steel BB’s.

  • 20 shot full size drop out metal magazine.

  • Smooth bore barrel.

  • Single and double action trigger.

  • 2.44 pounds (1107 grams).

  • Up to 400fps.

  • Replica of Taurus PT-92.

  • Made for Crosman by KWC in Taiwan.

Next up the Crosman American Classic P1322.

The American Classic P1322 is basically a .22 caliber version of the .177 caliber 1377 Pneumatic Pump Air Pistol. So make sure to watch the video reviews I have already done for the Crosman American Classic P1377. Other than caliber the .22 caliber version at least in Canada is more powerful since it has not been detuned for Canada import. The .22 caliber version has a claimed fps of 460 which is under our 500 fps import limitation while the standard non detuned .177 caliber version has a max claimed fps of up to 600 which can set off alarms at customs. For this reason the Crosman American Classic P1377 Canada version is detuned to shoot under 500 fps.

Crosman use to make a similar version of the Crosman American Classic P1322 called the Back Packer which had a slightly longer barrel and came with a removable stock. You can kind of replicate this gun by adding the stock but it will have a shorter barrel. Keep in mind there are a ton of mods available for this series of Crosman airguns including barrels, bolts, trigger, Internals stocks, scope mounts…

PHOTOSpecifications for the Crosman American Classic P1322:

  • Metal and plastic construction.

  • Pneumatic pump.

  • .22 caliber lead pellets.

  • Single shot bolt action.

  • Rifled metal barrel.

  • Single action only.

  • Up to 460fps using lead pellets (10 pumps).

  • 1.88 pounds (853 grams)

Keep posted for my full update reviews for these airguns...

Categories: .22 cal, 4.5mm / .177 cal, BB, CO2, Comparison, Full Auto, Multi-pump, Pellet, Pistol, Review, Semi Auto, Single Shot, YouTube Video Tags: American Classic, Crosman, Crosman PFAM98, P1322

SHOT Show 2017 KWA Booth

No Comments

And finally my last Vimeo video from SHOT Show 2017 in Las Vegas! Sorry there is no Interview this time with KWA but I did talk a lot with the KWA folks over at SHOT Show this year and I even got to test out their Laser Targeting System designed to be used with several specifi KWA guns by laser-ammo.com.

Unfortunately we don't carry the KWA brand in the replica Airguns store, a few models sneak in when being distriubted by another company like ASG in the case of the ASG MP9. I would love to carry KWA Airsoft Products in the future since they really do make very high quality Airsoft guns.

KWA has a great selection of Airsoft pistols and rifles in both Gas Blowback and AEG formats. The quality reminds me of the KJWors Airsoft guns we sell in the Replica Airguns Canada Store, you can really feel the quality when you pick them up and hold them for yourself.

Categories: Airsoft, Airsoft News, Blowback, CO2, Full Auto, GBB, Gas, Pistol, Replica Airguns News, Rifle, Semi Auto, YouTube Video Tags: KWA, SHOT Show, SHOT Show 2017

Umarex P99 Compact Clear Spring Airsoft Gun Table Top Review

No Comments

Type: Airsoft Pistol.

Manufacturer:Umarex.

Model:Walther P99 Compact

Materials: Mostly plastic with some metal parts.

Weight: .5 pounds (227 Grams).

Barrel: 3 inches, metal non-rifled with internal Hop-up.

Propulsion: Spring Piston.

Action: Single Shot, Single Action Only.

Ammunition Type: 6mm plastic Airsoft BB's.

Ammunition Capacity: 11 shot full size drop out magazine with 60 round reservoir.

FPS: 280 using .12 gram BB's.

Trigger Pull: The single action only trigger pull on the Umarex P99 Compact Clear Spring Airsoft Gun is a bit heavier than I expected since generally speaking single action triggers simply just need to release the hammer or striker. There is a little bit of take-up initially but then the release is fairly crisp, just a tad firm but since this is not an action shooter and a full rack of the slide is required to pre charge the internal spring, having a heavier trigger pull is not a big deal and did not seem to effect my accuracy in any way.

Accuracy: I didn't get a lot of shooting time with the Umarex P99 Compact Clear Spring Airsoft Gun but I can say it seemed to be shoot fairly accurately. I tested it out shooting on a paper target from 20 feet back using a non rested standing position. The Umarex P99 Compact Clear Spring Airsoft Gun did shoot a bit high and to the left but my 10 shot grouping was within 1.75 inches with the exception of one stray that shot a little more to the right. I was using .20 gram BB's but they did seem to get to the target pretty quickly and penetrate the paper fairly well. I would say they were traveling well over 200 fps.

Build Quality: The Umarex P99 Compact Clear Spring Airsoft Gun is about a $25 gun so you can't really expect too much in terms of quality materials but that said, the gun does feel solid and well put together. I had no issues shooing it and for the price you should get plenty of good use out of it.

Realism: The Umarex P99 Compact Clear Spring Airsoft Gun is realistic in terms of its shape, operation and even the Walther P99 licensing and trade marks. But as is expected being a clear plastic gun it falls short in terms of feeling and looking the part of a real gun. But that's kind of the point here, this gun is supposed to clearly look like and Airsoft gun and not a real gun including the orange red tip.

Purchase it from: The Replica Airguns Store

Pros:

  • Super low cost and even come with an extra mag and some starter BB’s.

  • Full size drop out mags are nice.

  • All the parts feel pretty tight, does not feel hokey, even has some metal parts where they are needed.

  • Has a rail for accessories.

  • No CO2 required, just your Airsoft BB’s.

  • Walther licensing and Trademarks.

  • Slide stays back when out of BB’s.

  • Has internal Hop-up.

  • Has a floating barrel like the real steel version would.

  • Makes a good starter pistol for someone getting into the hobby that may not want a gun that looks too realistic.

Cons:

  • Is kind of on the light side at about half a pound.

  • The single action trigger is a bit heavy but works fine, you're not going to be shooting rapped fire with this one anyway.

  • Being a clear gun obviously takes away from the realism but that is the point of this gun so as not be confused with a real gun.

  • Shoots a bit high and to the left.

Comments:

Right from the get go I was not expecting much from the Umarex P99 Compact Clear Spring Airsoft Gunbeing a bit of an Airgun snob and personally tending to stay away from the like of these clear plastic non-blowback super low cost Airsoft pistols. But after playing around with it for a bit I could really see how a first time Airsoft buyer could really enjoy the Umarex P99 Compact Clear Spring Airsoft Gun. It shoots just fine and costs next to nothing to buy and shoot. And I know there are many younger folks that watch my video reviews and perhaps their parents may be sitting on the fence about allowing them to buy an Airsoft gun out of fear that so many of them look so real. The Umarex P99 Compact Clear Spring Airsoft Gun clearly looks like an Airsoft gun which makes it pretty hard to get in trouble with yet you can still enjoy the Airsoft shooting experience without freaking your parents out!

My Vimeo Video Review for the Umarex P99 Compact Clear Spring Airsoft Gun:

 
Categories: 6mm, Airsoft, Pistol, Review, Single Shot, Spring Piston, YouTube Video Tags: P99 Compact, Umarex

My 2016 Favorite Replica Airgun Picks of the Year

No Comments

It's been a great year for Replica Airguns and I wanted to share with everyone some of my favorites that I reviewed this year. In this Vimeo Video I show some of my top Replica Airgun picks for 2016 and talk a little bit about each one and what I like about it.

Here is a list of the Replica Airguns in this lineup:

Categories: 4.5mm / .177 cal, 6mm, Airsoft, BB, Blowback, CO2, GBB, Pellet, Pistol, Review, Revolver, Rifle, Semi Auto, YouTube Video Tags: ASG, AirVenturi, KJWorks, Sig Sauer, Umarex

Why is My CO2 Airgun Not Working?

23 Comments

One of the most common types of question I get on my Replica Airguns YouTube channel has to be something like… Why is my Airgun not working? Most of the time the amount of info about the problem is limited to something like… “It was working yesterday but now it’s not working anymore” or something like “when I pull the trigger nothing happens”. My personal favorite is… “I took my gun apart and now it doesn’t work!”

I just made a similar video for Blank Guns and as I said in that video, trying to trouble shoot a mechanical or technical problem over the internet is very difficult, this goes for cars, guns, computers or what have you…

In this Why is My CO2 Airgun Not Working video I will however cover some of the more common and obvious problems I have seen relating to why a CO2 Airgun may not be working properly. I really don’t get a lot of questions about Spring Piston or Pump Airguns so I will be focusing on CO2 Airguns in this video. There will be a lot of crossover with CO2 Airsoft guns so this video may be helpful for some of you Airsofters out there

First let’s get the super obvious stuff out of the way! 

  • Did you put a new CO2 cartridge in it and is it pierced all the way?

  • Did you load BB’s or Pellets into the Airguns magazine and is the magazine in the gun correctly?

  • Is the safety off?

  • If the gun is a blowback semi auto single action Airgun then did you pull the slide back prior to the first shot?

CO2 Related Problems:

Not all CO2 cartridges are created equal, they often have slightly different shaped nubs on them and some brands will work better than others in different Airguns. If the shape of the CO2 nub does not fit properly into the valve area then it may not pierce or it could pierce but then not allow you to tighten it all the way losing all the CO2 in the process. If the CO2 is coming form the airguns handle to CO2 Valve area then this is an indication that your problem is related to the area where the CO2 enters the airgun.

There is a seal where the CO2 cartridge buts up to the valve, this seal can be damaged or even deformed from usage or even leaving your CO2 in the gun for too long. The outside CO2 Valve seal can also take the shape of a specific CO2 nub so when you use a different brand CO2 the seal may not properly make concat with the new CO2 type you are using, again causing leaking or even the total loss of all your CO2. Watch my YouTube video on “How to Fix Leaking CO2 in an Airgun”.

CO2 Valve Related Problems:

Again, make sure that Outside CO2 Valve Seal is in good condition and any leaking is not being caused by this problem, if you have checked the Out Side Seal and everything is OK with it then perhaps there is a problem with the CO2 valve?

One indication that your CO2 Valve might be the culprit is the total loss of all your CO2 when you try to insert and tighten a new CO2 Cartridge. Usually all the CO2 will exit the barrel, not the handle or valve area. What may be happening is the valve is stuck open or the internal seal is broken or deformed. If this is the case you will have to remove the valve and have a look inside, this is a lot easier on CO2 airguns that have the CO2 valve in the magazine, if the CO2 valve is in the actual Airguns then a lot more disassembly may be required and I would recommend an Airgun technician take care of this for you.

If the gavel is in the magazine then you will have to unscrew it, you may require a special tool for this? Once the valve is out of the magazine  take a look inside and examine the internal seal, also look for any bits of metal shavings as they can disrupt the action of the valve causing leaking. Give the inside of the valve a good clean and then lubricate it with some silence spray. hopefully that fixes your problem!

BB’s getting Stuck in the Blowback Gas Tube:

I have actually made a dedicated video for this problem so I will put a link to it in the description of this video. The main reason people may have this problem is because we all like to rack that slide on our full blowback Airguns, but if you have a fully loaded magazine then each time you reach that slide without shooting the gun, you are inadvertently trying to load another BB into the breach area, the breach is only designed to hold one BB at a time so after a few racks of the slide the newly loaded have no place to go but into the Gas Tube where they can get stuck and cause having to the operation of your Full Blowback CO2 Airgun.

BB’s Rolling Out of the Barrel of Your CO2 Airgun:

This is not actually a fault of the gun but happens because of the way the gun is designed. This situation can happen with certain CO2 Airguns when the gun user pulls the trigger really slowly while the gun is point slightly in a downward position. What is actually happening is the first part of the trigger is made to draw a BB from the magazine into the breach of the gun. If the barrel of the gun does not have a rubber hop-up stopper in it then the BB is free to roll down the barrel and out of the gun. How do you fix this problem? Be more committed to your trigger pull and or shoot at a target that is not so low. Perhaps place your targets slightly higher than the gun so the barrel is not pointing down, especially if you like to take your time with the trigger :)

A Little Maintenance Can Go a Long Way!

Sometimes a good cleans is all you need to do to get things working as they should, again I have already made video Tutorial Showing “How to Clean Airguns and Blank Guns”.

What about stuff like My Airgun is jammed or my trigger is stuck or some random part fell out of my gun?

There is only so much I can cover in this video, most other problems are going to get a bit more complicated to fix and I suggest if your Airgun is not working and the suggestions I have made in this video do not solve your problem, then consider taking your gun into a gun tech.

Categories: 4.5mm / .177 cal, 6mm, Airsoft, BB, Blowback, CO2, GBB, How To, Pellet, Pistol, Review, Semi Auto, YouTube Video Tags:

Airsoft Gun Power Source Pro’s & Con’s

2 Comments

Power Sources Covered in this review: CO2 - Green Gas / Propane - Spring - AEG / AEP (Automatic Electric Gun - Airsoft Electric Pistol)

Pro’s:

  • CO2 Airsoft Guns allow for fast repeat shooting, great for action shooters, generally CO2 Airsoft Guns will have a little more power then Green Gas Airsoft Guns. There is no need to pump or cock your CO2 powered Airsoft gun in-between shots and a CO2 power source can allow for a very realistic action of the gun you are shooting. 

  • Green Gas (Propane) Airsoft Guns operate much the same as CO2 Airsoft guns so they all make for great action shooters and the Green Gas powers the mechanical operation allowing for very realistic operation. Green Gas (Propane) Airsoft Guns can cost a little bit less to operate that a CO2 Airsoft Gun especially if you plan to use Propane as it can be cheaper to buy than the smaller 12 gram CO2 Cartridges.

  • Spring Airsoft Guns are generally fairly basic and low cost so they are the usually the most affordable Airsoft guns to buy. There is no need to buy CO2 or Green Gas or even a Battery and Charger Setup so the cost to shoot Spring Airsoft Guns is only going to be subject to the Airsoft BB’s you plan on buying.

  • AEG (Automatic Electric Guns) have the most consistent power as they use a spring internally that the electric motor draws back before each shot, the internal spring will essentially apply the same force to the Airsoft BB’s with each shot. AEG (Automatic Electric Guns) are a great option when you are wanting a Full Auto Airsoft gun since there is no cool down effect and as long as your batteries are charged and you have Airsoft BB’s in your magazine, the gun will simply keep shooting. AEG (Automatic Electric Guns) allow for the highest capacity magazines and often hold as many as 500 Airsoft BB’s in a single magazine. So if you’re looking for raw firepower an AEG or AEP Airsoft Gun is your best option. Once you have purchased your AEG (Automatic Electric Gun) and a battery and charger setup, they are fairly inexpensive to operate since no CO2 or Green Gas is required.

Con’s:

  • CO2 Airsoft Guns require the additional cost to buy the CO2 cartridges as they will not function without it. CO2 Airsoft Guns have a limited power output and lose power as you shoot and use up the CO2. CO2 Airsoft Guns are effected by hot and cold temperatures and will have less power in colder temperatures and may not even work in super cold environments. CO2 Airsoft Guns will have a more conservative ammunition capacity since too high of a capacity magazine would freeze up the magazine and even the gun.  

  • Again since Green Gas (Propane) Airsoft Guns work much like CO2 Airsoft Guns, they are effected by cool down and lose power when shoot quickly or as the Green Gas or Propane runs low. Green Gas does not expand as much as CO2 so it will not be as powerful and even less effective in colder temperatures. Green Gas Airsoft Guns will have a more conservative ammunition capacity since too high of a capacity magazine would freeze up.

  • Spring Airsoft Guns are not the best action shooters since you need to manually operate the slide to pullback the spring prior to each shot, this does work well with Pump, Lever and Bolt Action Airsoft guns but is not the best option for pistols since most real steel pistols operate in semi auto mode.

  • If you plan to use your AEG (Automatic Electric Gun) in a battle then it will require a multi battery setup which does cost a bit more upfront. AEG (Automatic Electric Guns) are know to not operate as realistically as a CO2 or Green Gas Airsoft gun since CO2 and Green Gas Guns do allow for the same realistic mechanical operation which can give very believable blowback operation, this is hard to replica with an AEG Airsoft Gun.

Categories: 6mm, AEG, Airsoft, CO2, Comparison, Full Auto, GBB, Gas, Pistol, Repeater, Review, Revolver, Rifle, Semi Auto, YouTube Video Tags:

Airgun Power Source Pro’s & Con’s

No Comments

Power Sources Covered in this review: CO2 - Spring Piston - Variable Pump -HPA (High Pressure Air)

Pro’s:

  • CO2 Airguns allow for fast repeat shooting, great for action shooters, generally CO2 Airguns will supply a medium power range. No need to pump or cock your CO2 powered weapon in-between shots and a CO2 power source can allow for a very realistic action of the gun you are shooting.

  • Spring Piston Airguns are best suited of single shot situations, they can provide low to high power output depending on the spring used. Spring Piston Airguns are very low cost to operate since you only need to buy the Pellets or BB’s. Spring Piston Airguns are not greatly effected by outside temperatures.

  • Variable Pump Airguns allow you to decide how much power your gun will have and can offer very high power output depending on the Airgun. Variable Pump Airguns are very low cost to operate since you only need to buy the Pellets or BB’s. Variable Pump Airguns are not greatly effected by outside temperatures. Variable Pump Airguns generally have very low recoil and vibration.

  • HPA (High Pressure Air) Airguns generally do not require pumping or cocking in-between shots and some even come in semi automatic or bolt action. HPA Airguns can have very high power output and even be used on larger game using large caliber ammunition. HPA Air Rifles have lower recoil and low vibration. HPA Airguns can be charged ahead off time so they are ready for use when you need them.

Con’s:

  • CO2 Airguns require the additional cost to buy the CO2 as they do not function without it. CO2 Airguns have a limited power output and lose power as you shoot and use up the CO2. CO2 Airguns are effected by hot and cold temperatures and will have less power in colder temperatures and may not even work in super cold environments.

  • Spring Piston Airguns require cocking before each shot. Spring Piston Airguns can have a lot of recoil and vibration, so much so that special optics must be considered when buying an optical sight. The action of the spring recoil can effect accuracy, especially if you are not use to the vibration and recoil or have spent some time practicing using a Spring Piston Airgun.

  • Variable Pump Airguns will require multiple pumps to achieved maximum power output which can take some time in-between shots. So you are going to have to work for each shot.

  • HPA (High Pressure Air) Airguns require the use of a manual pump to fill their built in air tank to maximum pressure and it does take a lot of time to manual fill an HPA tank. Alternatively you can have the air tank filled at a shop or buy a pressurization system similar to a scuba tank out paintball setup, the cost of this setup can be very high but will save you the castle of manually pumping air in to your HPA Airgun. HPA Airguns are generally a little more bulky then other Airgun systems since they have to accommodate fairly large air pressure tanks.

Categories: .20 cal, .22 cal, 4.5mm / .177 cal, BB, Blowback, Break Barrel, Bulk Air, CO2, Multi-pump, PCP, Pellet, Pistol, Repeater, Revolver, Rifle, Semi Auto, Single Shot, Spring Piston, YouTube Video Tags:

Why is an Air Rifle Better for Pest Control Than an Air Pistol?

1 Comment

Power:
Generally speaking a longer barrel is going to allow for more power. If you compare most CO2 pellet pistols to CO2 Pellet Rifles, you will find that the CO2 Pellet Pistol will generally shoot about 300-400 fps using a standard lead Pellet. On the other hand many CO2 Pellet Rifles can get up to as high as 600 fps which is much better speed for humanly shooting some smaller pests.

If you are talking about Springer or Variable Pump Air Pistols versus their Air Rifle counterparts, again the Air rifles will generally shoot with much more power. I have seen some none CO2 Air Pistols shoot up into the 500-600 fps range but again compered to none CO2 Air Rifles, they can even double these numbers.

Some of you may ask about Steel BB Pistols and Rifles. I personally would never really sue this type of ammunition for pest control simply because most BB Rifles have much less raw power than Pellet Rifles and steel BB’s will not be as accurate at any type of longer distance.

Stability:
When holding any rifle from the shoulder, you have three point of contact with your body spread out in a much longer distance than a two handed pistol grip. Holding steady even without a rested position is much easier using a rifle. Even when using a rested position, the rifle will more stable.

Accuracy:
A big factor in accuracy is stability but there are also other factors to consider. Barrel length its self does not make the gun more accurate, you only need a few inches of barrel length to get constant accurate results from a gun. What makes longer barreled guns more accurate is the distance between the rear and front sight. The closer the sights are together, the more margin for error there is, the longer you spread out the sights from each other, the more accurate the sighting system becomes.

Overall More Humain:
When you consider Air Rifles tend to have higher power, better accuracy and overall more consistency than shorter barreled Air Pistols. The logical choice for humanly shooting a Pest is to use the Air Rifle. The last thing you want to do is make any animal suffer, even if it has been causing a lot of havoc around your home or farm or place of business.

Categories: .20 cal, .22 cal, 4.5mm / .177 cal, BB, Break Barrel, Bulk Air, CO2, Comparison, Non Airguns, PCP, Pellet, Pistol, Revolver, Rifle, Scope, Semi Auto, Single Shot, Spring Piston, YouTube Video Tags: