In this Field Test Shooting Video I put the Webley Valuemax 22 Caliber Spring Piston Break Barrel Rifle through my standard Replica Airguns Indoor Field Test protocol by first testing out the velocity and placing 5 rounds through my Chronograph to see what the actual real world fps is using 14.3 grain lead pellets. I then setup a fresh paper target 30 feet downrange and place 10 pellets into it to see what type of grouping I can get. If you have not already watched my Table Top Video for this Break Barrel Spring Piston Pellet Rifle then make sure to do so for more details, specifications and close up video.
Starting off with my real world velocity test for the Webley Valuemax 22 Caliber Spring Piston Break Barrel Rifle, I went with 14.3 grain lead pellets which are I would say on the heavier side. Even so I managed to hit 478 fps which produced a nice 7.26 foot pounds of energy which by the way is almost 10 Joules! If you are wondering about Canadian legalities, as long as I do not go over 500 fps AND go over 4.2 foot pounds (both thresholds must be exceeded), then this Airgun is considered a non-regulated firearm and does not require a firearms license.
Moving on to the accuracy portion of my Indoor Field Test in the Replica Airguns Sea Can. As always I placed a brand new paper target 30 feet downrange and proceeded to shoot ten 14.3 grain lead pellets from a rested and seated shooting position to allow for best possible results with as little human error but I am imperfect so some human error is always present. I was using the open fiver optic sights on the Webley Valuemax 22 Caliber Spring Piston Break Barrel Rifle rather than a scope even thought there is a dovetail rail with included scope stop. To be honest I was expecting a better grouping, something close to half an inch but on this day with this ammo choice I was closer to 1.5 to even 2 inches. I did see several pellets land in a tighter sub group but some came out of this group enlarging the grouping. I would like to try a different pellet choice to see if I can do better as I believe this rifle has way more potential.
In terms of power the Webley Valuemax 22 Caliber Spring Piston Break Barrel Pellet Rifle is about has high as you can go before it becomes a regulated firearm here in Canada so no complaints in that department. Again I was disappointed in the accuracy but I honestly believe a different pellet choice could fix that problem as I have seen often with other Pellet Rifles. Once the right pellet choice is made and granted a more consistent and tighter grouping is achieved, this Spring Piston Pellet Rifle could make a decent small pest control airgun!
Type: Pellet Rifle. Distributer:Webley & Scott. Model:Valuemax. Materials: Metal and polymer build. Weight: 6.4 pounds (2900 grams). Barrel: 17.7 inches (450mm), rifled. Total Length: 43 inches (1092mm) Propulsion: Spring Piston Action: Break Barrel. Ammunition Type: .22 Caliber Pellets. Ammunition Capacity: Single Shot. FPS: 499.
Trigger Pull: The trigger pull on the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle is fairly nice There is a little bit of very light take up followed by a vert light release , the take up or travel length can be adjusted on this Air Rifle but that is the only trigger adjustment you can make and perhaps all that is needed.
Accuracy: I have not performed my Field Test Shooting Video for the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle but I did get to take around 20 or so shots with it when I was trying to get it to diesel for me. It looks ot me like it is going to be nice and accurate as I was not even really going for accuracy and it seemed to already be grouping fairly tight. I was recoding fps using my Chronograph as I was trying to find out if by adding some oil to the spring piston chamber could get it to diesel which it never did for me, I was however to establish that the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle shot right around 470-480 fps using 14.3 grain lead pellets which worked out to right around 7.32 foot pounds of energy. I will know a lot more when I do my official Field Test Shooting Video next week.
Build Quality: Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle is built to be a value priced Airgun hence the name (Valuemax), that said it is maid well enough with lots of metal and of course some plastic or in this case mostly nylon as the stock is a solid nylon piece. Other than the stock the plastic parts are found to be in the sights and trigger guard, everything else seems to be metal.
Realism: The Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle is not a replica or copy of any real steel gun in production but it does look like a traditional hunting rifle in basic shape so make sure to transport thank airgun as if it was a real gun. Either in a gun case or perhaps a blanket in your trunk and always obey any laws for gun position and transportation in your area.
Pros:
Inexpensive price tag for well made decent performer.
Initial test showed to have good accuracy and power! (more to come).
Fully adjustable sights with optical TRUGLO Fiber Optics.
Can add a magnified optical scope using the top built in dovetail rail.
Nylon fiber stock is durable and functional with the addition of a vented rubber buttplate.
Trigger feels decent and is also adjustable for travel length.
Rear thumb safety resets after each break of the barrel.
Nice light and short single action trigger.
Would be good for small pest control because of decent FPS and good accuracy.
Cons:
Included sights are mostly plastic.
The Valuemax version has a more basic less adjustable trigger.
Detuned down to under 500 fps for Canada import as non-regulated Firearm.
Comments: I am looking forward to performing my Indoor Field Test Shooting Video for the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle to see what it can really do in terms of accuracy so stay posted for that video next week. Overall if you are lucky enough to already have one or can get your hands on one since this rifle is discontinued in some area, I think this is a great Break Piston Air Rifle especially if you live in Canada and want the most bang for your buck. I am not only talking about cost verses features, I also mean power and energy since the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle is a .22 caliber Air Rifle that can shoot really close to 500 fps with a nice heavy grain lead pellet achieving decent energy levels reasonable enough for small pest control. The Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle is not feature less, it does include a reseting safety, anti bear trap system, dove tail mounts with an included scope stop, fiver optic adjustable sights and a vert ergonomic textured nylon stock. All in all great value for what you pay!
My Vimeo Videos for the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle:
In this Field Test Shooting Video I put the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle through the regular Replica Airguns Indoor Field Test by first testing out the velocity and placing several rounds through my Chronograph to see what the actual fps is using both .20 gram and .40 gram Airsoft BB’s. Then I setup a fresh paper target 30 feet downrange and place 10 rounds into it to see how tight of a grouping I can get. If you have not already watched my Table Top Video for this Sniper Airsoft Riffle, then make sure to do so for more details, specifications and close up video.
Starting off with my real world velocity test for the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle I decided to use both .20 and .40 gram Airsoft BB’s to see what a difference of double the weigth form the claimed for would actually be since for the most art this Airsoft Sniper Rifle is really meant to be using heavier Airsoft BB’ closer to the .40 gram weight. I was kind of expecting the heavier .40 gram BB’s to shoot almost half as fast since they where double the weight bu this was not the case! I shot 5 rounds with each weight Airsoft BB and with the .20 gram I averaged 479 which was actually faster than claimed, When I switched up to the .40 gram Airsoft BB’s I was surprised to get an average of 373 so only around 100 fps slower!
Moving on to the accuracy portion of my Indoor Field Test here in the Replica Airguns Sea Can, as always I placed a fresh paper target 30 feet downrange and proceeded to shoot 10 .40 gram Airsoft rounds into it from a rested and seated shooting position to allow for best possible results with as little human error added in. I was using a 4x optical scope since the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle has a the added rail on top just fo this purpose and I would imaging most people are going to want to add a magnified scope to this Airsoft Sniper Rifle rather than use the built in pop iron sights that by the way are not adjustable. I know 30 feet is not the range one would be shooting this rifle at but it’s all I have for an indoor shooting range and it will give us an idea of what we can expect shooting further out… as in a nice tight group at 30 feet is going to mean better accuracy than a spread out grouping art 30 feet. I will say the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle probably got one of the best groupings for an Airsoft Rifle that I have tested at 30 feet placing all 10 rounds within about an inch to an inch an a half.
I would like to take this Airsoft Sniper Rifle outside and see what it can do at much further out ranges again using nice and heavy Airsoft BB’s when it gets a bit warmer and stops raining so much :) But for now my Indoor Field Test performed about as good of a result as I can expect. The ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle is a really well made which paid off in two it performed for me. I don’t really see any need to upgrade this Airsoft Sniper Rifle other than adding an optical scope and perhaps investing in some high quality Airsoft Ammo.
Type: Airsoft Rifle. Distributer:ASG. Model:Steyr Arms Scout. Materials: Metal and polymer build. Weight: 6.5 pounds (2950 grams). Barrel: 14.5 inches (368mm), non-rifled. Total Length: 39.5 inches (1000mm) Propulsion: Spring Piston Action: Bolt action repeater. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: 32 round magazine. FPS: 443. Type: Black and Grey versions.
Trigger Pull: The trigger pull on the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle is short light and crisp. Working the bolt precooks the trigger for single action only shooting allowing for just the release of the hammer. There is very little take up and no creep at all, just a nice light and predictable trigger pull.
Accuracy: I have not performed my Field Test Shooting Video for the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle so stay posted for that. ASG claims around 4430 fps velocity with the preinstalled M140 spring, you can upgrade the spring all the way up to an M190 spring for even higher potential fps. In terms of accuracy I am also expecting good results so check back next week for my Indoor Field Test Shooting Video for the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle.
Build Quality: The ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle is well built with lots of high quality component not only inside but also internally. You will find a metal barrel and receiver along with metal bolt, trigger and rear sight, the front sight is however plastic. I donate really thin k you will be using the pop sights all that much as they are not adjustable and this gun really begs for a nice optical scope. The nylon polymer stock has micro-texturing to help with the grip in all weather conditions.
Realism: The ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle is based on the real steel 7.62 NATO Steyr Scout and even incorporates the integrated folding bipod legs like the original. For the most part they look identical but you will find the actual magazine on the Airsoft version is placed further up the stock to allow for the feeding of the Airsoft BB’s which does make the actual inner barrel shorter by about 4-5 inches.
Pros:
Nylon Polymer stock with micro-texturing.
Railed metal receiver with laser-etched Steyr trademarks.
Integrated folding bipod legs on left and right sides of the stock.
Flip-up backup front and rear sights.
Accessory slot on bottom of stock for mounting of optional bipod rail.
Millet QD sling loop attachment points.
Front dummy magazine.
Rear dummy magazine with storage for a spare magazine.
Removable stock spacer pads for length-of-pull adjustment.
90 degree trigger with steel sear.
90 degree aluminum piston with dual glide rings and steel base.
Silent Air Brake piston head.
Silent cylinder head with shock-absorbing padding.
9mm stainless steel ball bearing spring guide.
Bore-up steel cylinder with 12.5% more air volume than stock cylinders.
Hop-up unit with both side-lever adjustment and TDC screw adjustment options.
Steel CNC-machined hop-up arm.
03mm tight-bore inner barrel.
60 degree Modify Predator enhanced hop-up bucking preinstalled (50 and 70 degree buckings available separately).
Compatible with VSR-spec inner barrels.
450 FPS with pre-installed M140 spring.
Can take up to a M190 spring with no upgrades needed.
Cons:
32-round magazine.
Recommended ammo: 0.36g BBs and above, 0.4g optimal.
Comments: I am looking forward to performing my Indoor Field Test Shooting Video for the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle. I won’t be able to test it out perhaps as far range as I would like to since I will be shooting it in the Replica Airguns Indoor Shooting range which allows me to test at 30 feet. That should give me a good overall idea on at least what it may be capable of since if we can get a tight group at 30 feet we should also be able to get a tight group at longer ranges with proper hop-up and heavier BB selection. I do plan on placing a scope on the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle to give it the best possible chance of performing at it’s best and really hope to see a good result from it.
My Vimeo Videos for the ASG Steyr Arms Scout Bolt Action Spring Airsoft Rifle:
In this Field Test Shooting Video I put the ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun through it’s paces by first testing out the velocity placing several rounds through my Chronograph, and then I setup a paper target downrange and place 10 rounds into it to see how tight of a grouping I can get. If you have not already watched my Table Top Video for this Airsoft Sniper Pistol/Rifle then make sure to do so for more details, specifications and close up video.
Starting off with my real world velocity test for the ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun, I decided to use .28 gram Airsoft BB’s for this entire Field test Shooting video so I was expecting to get somewhere between 20-25% slower fps velocity as compared to the standard tested .20 gram Airsoft BB’s. After placing around 6 shots through my Chronograph I averaged 328 fps which ended up being 18% slower than the claimed 400 fps made by ASG. I would image if I had used .20 gram Airsoft BB’s I may have even exceeded 400 fps.
Moving on to the accuracy portion of my Indoor Field Test here in the Replica Airguns Sea Can, as always I placed a fresh paper target 30 feet downrange and proceeded to shoot 10 rounds into it from a rested and seated shooting position to allow for best possible results with as little human factor added in. I was using a 4x optical scope since the ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun does not come with any type of sighting system included so I did have to sight it in initially. I did manage to get a nice 1.5 inch grouping fairly close to the bullseye but I did notice that if I angled the barrel down a bit, BB’s would roll out of the barrel which made me wonder if the hop-up was set high enough to engage a BB.
So I did my second test with the hop-up set in the middle range and this time BB’s did not fall out of the barrel when angled down. After the hop-up adjustment I did notice I was shooting a bit higher which is expected with more hop-up adjustment so if you are experiencing BB’s falling out of the barrel then make sure to adjust your hop-up a bit tighter.
All in all the ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun performed very well for me especially once I got the hop-up figured out. And I do think it makes for a really nice compact Sniper Rifle if bulkiness is a factor for you, if not then checkout the Rifle version of this gun with the more traditional but-stock and longer barrel.
Type: Airsoft Rifle. Distributer:ASG. Model:Action Army T-11. Materials: Metal and polymer build. Weight: 3.9/4.5 pounds. Barrel: 11.8 inches, non-rifled. Total Length: 34.7/43.3 inches Propulsion: Spring Action: Bolt action repeater. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: 50 round magazine. FPS: 400-430. Type: Pistol and Rifle versions.
Trigger Pull: The trigger pull on ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun is light, short and crisp. There is virtually no take-up and the release point has no creep to it. I would say it is not too light but for sure one of the lighter trigger s I have tested on a Airsoft rifle.
Accuracy: I have not performed my Field Test Shooting Video for the ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun so stay posted for that. ASG claims around 400-430 fps velocity depending on the version which is kind of weird since both have the exact same barrel length internally and I would assume both use the same mechanical part throughout? I don’t have the rifle version to compare to but I will for sure test the velocity using my Chronograph for the pistol version when I do my Field Test Shooting Review along with accuracy performance.
Build Quality: The ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun is well built for sure, it feels really solid in the hadn't and has good overall weigth to it for it’s size. You will find lots of metal parts where they need to be as in the inner and outer barrel, receiver, bolt, trigger, magazine release and I am sure most mechanical internal parts. Fit and finish is also very good.
Realism: The ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun is not a replace of any gun I know of but does have tab least the pistol version does look like a sawn off shotgun more than a sniper rifle. The gun overall all is very modern and ergonomic looking but in terms of being a replica of any specific real steel gun in production I don’t know of any it would resemble?
Pros:
Top and bottom rails for lots of accessory add on options.
Can swap over to a rifle version by adding on an interchangeable but-stock.
Mock magazine allows for storage and transport of tools plus extras.
Safety switch is in a great location for right handed shooters.
Comes with included hand stop.
Solid construction with lots of metal parts where they are important.
Ability to add side rails.
Great option if you are looking for a more compact sniper rifle.
Comes in Pistol and Rifle versions.
Cons:
Has an orange tip.
Does not come with sights, will need to add some sort of optical or red dot sight.
Does not come with speed loader, would have been nice.
Comments: I am looking forward to performing my Indoor Field Test Shooting Video for the ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun. I won’t be able to test it out perhaps as far range as I would like to since I will be shooting it in the Replica Airguns Indoor Shooting range which allows me to test at 30 feet. That should give us a good overall idea on at least what it may be capable of since if we can get a tight group at 30 feet we should also be able to get a tight group at longer ranges with proper hop-up and BB selection. I like the option of being able to choose either the Pistol or Rifle version and both should perform about the same. Having the Pistol version will allow for a much more compact Sniper Rifle option much better suited for shooting in a variety of situations.
My Vimeo Videos for the ASG Action Army T-11 Spring Powered Bolt Action Airsoft Gun:
In this Replica Airguns Vimeo Field Test Shooting Video I put the KWC / Umarex Mod. 92 A1 andElite Force 1911 TAC CO2 Blowback Airsoft Pistols through my Indoor Sea Can Shooting Test. Fist I find out what the real world velocity is by placing 5 rounds through my Chronograph and average out the FPS. I then shoot 10 rounds on a paper target for 30 feet back using a semi rested shooting position, sand bag up front and seated in the back.
Starting with my velocity test for both CO2 Blowback Airsoft Pistols I made sure to use a brand new CO2 along with .25 gram Airsoft BB’s so a bit heavier than what was used for the official stats. Both Umarex Airsoft Pistols shot really similar velocities with the Umarex Beretta Mod. 92 A1 averaging 364 FPS and the Umarex Elite Force 1911 TAC averaging 365 FPS. If I had been using .20 gram Airsoft BB’s I am sure these numbers would have been closer to the claimed 400 or so FPS.
Moving on to the accuracy test again I performed this test which each Umarex CO2 Blowback Airsoft Pistol. The Umarex Beretta Mod. 92 A1 performed a little bit better than the 1911 with all 10 shots grouping within 1.5 inches and very well centered on the target. The Umarex Elite Force 1911 TAC did have a slightly wider grouping closer to 2 inches and was a lilt bit high on the target but center nicely left to right. Of course the full auto mode on the Umarex Beretta Mod. 92 A1 did not produce anything even close to a tight group but it is always fun shooting in full auto :)
All in all both of these KWC / Umarex CO2 Blowback Airsoft Pistols performed well for me in terms of meeting their expectations for velocity and accuracy. We have them in our online Replica Airguns Stores in either KWC Unlicensed or Umarex Licensed versions so take your pick!
In this Vimeo Replica Airguns Update Video I take a look at three CO2 Airguns, one is a 4.5mm Steel BB revolver distributed by Barra and two are CO2 Blowback Airsoft Pistols distributed by Umarex. All of these CO2 Airguns I have previously reviewed in slightly different versions either barrel length and finish or Steel BB as compared to 6mm Airsoft So checkout why other reviews on similar version Airguns.
The Barra Barra Schofield CO2 BB Revolver is a replica of the Schofield No. 3 single action revolver and utilizes 6 reloadable shells for a very realistic shooting experience. It is very solid in construction bing made mostly out of metal and weighs in at around 2.4 pounds. This version shots 4.5 mm Steel BBs at a velocity of up to 400 fps. It comes in a variety of barrel lengths and finishes so amen sure to have a look in our Online Replica Airguns Store for what we have available…
Next up from Umarex is the fully licensed Beretta Pietro Mod. 92 A1 CO2 Blowback Semi and Full Auto Airsoft Pistol, this product is distributed by Umarex but is made by KWC. Another solid metal pistol with a hefty 2.4 pound weigth that holds 21 rounds in its full size drop out metal magazine and offers both semi and full auto shooting at the flick of a switch!
Again from Umarex I showcase the Elite Force 1911 Tac CO2 Blowback Airsoft Pistol and like the Beretta Pietro it too is made in the KWC factory for Umarex. The 1911 Tac as the name suggest is a tactical version of the standard Colt 1911 but with some upgrades like a skeletonized hammer and trigger along with an ambidextrous safety, white dot sights front and back and a picatinny rail on the frame for add ons. You can expect velocity to be somewhere in the 400 fps range and the full size drop out metal magazine holds 15 Airsoft BB’s.
In this Preview Update Video three newer products, two Umarex Airsoft CO2 Blowback Pistols and one CO2 Blowback BB Pistol from Crosman. This is far from a full review which I will remaking for all of these Airguns in the near future. I simply go over some of the main specifications and show you quickly around each Airgun.
Type: GBB Airsoft Pistol. Manufacturer: WE Airsoft Model:1039 M2 Materials: Mostly all metal build. Weight: 2.43 pounds (1100 grams). Barrel: 4.53 inches, non-rifled. Length: 8.5 inches. Propulsion: Green Gas Action: Semi & full Auto, single and double action trigger. Ammunition Type: 6mm Plastic Airsoft BB's. Ammunition Capacity: 26 round full size dropout metal magazine. FPS: 366+.
Trigger Pull: The trigger pull on the WE M92 GBB Full Auto Airsoft Pistol is good in both single and double action. Double action as expected has the longer heavier pull but is still smooth and fairly light with a predictable release. Single action shooting has a much shorter trigger pull with a bit of take-up and an even lighter release than in double action shooting mode.
Accuracy: This is one of those times I actually performed my Field Test Portion of my Review first so I do have some feedback in terms of the accuracy and velocity for the WE M92 GBB Full Auto Airsoft Pistol. WE claims an fps of around 366+ using the extended barrel that comes with it so this is how I tested it. I did use .26 gram airsoft BB’s so the fps was a bit lower but I did get close to 320 fps, So you should expect around a 20% increase in FPS using .20 gram Airsoft BB’s, so closer to 360-380 fps. In terms of accuracy I did notice that the WE M92 GBB Full Auto Airsoft Pistol shot rather low for me, as much as 8 inches at 30 feet out, perhaps adjustment get hop-up will fix that, at longer ranges it should… That said I found I was able to get around a 1-5.2 inch 10 round grouping at 30 feet out. In terms of full auto, all I can say is don’t expect to hit very much you point at as the gun really likes to rock around!
Build Quality: The WE M92 GBB Full Auto Airsoft Pistol is a really gorgeous looking pistol and has one of my favorite looking finishes in that stainless steel look. You will find it has an overall solid build quality, it is virtually all metal with only the grips and some internal parts like the gas chamber and nozzle being plastic. There is almost zero slide wiggle and all in all this Airsoft pistol performed great for me with no mechanical problems.
Realism: As is with most Full Blowback Airsoft Pistols they are built to look and act the part of their real steel counterparts and the WE M92 GBB Full Auto Airsoft Pistol is no exception! All mechanical parts work as intended and you can easily field strip the WE M92 GBB Full Auto Airsoft Pistol to swap out the internal barrel and adjust the hop-up. I like the fact that WE Airsoft color matched the magazine rather than simply shipping it with the black magazine as I have found some other companies do.
Pros:
All metal pistol with good weight to it.
Crisp firm full blowback operation.
Excellent fit and finish.
No markings on the metal parts at all, just the WE branding on the grips.
Color matching magazine.
Gun will accept real Beretta M9 grips.
Semi and full auto selector safety switch.
White dot sights front and back.
Good fps, right around the claimed 366 using .20 gram Airsoft BB’s.
Very believable working replica of the real steel Beretta M9 Pistol.
Fully field strip-able.
Comes with extension barrel and replaceable inner barrel if not going to use extension.
Cons:
No marking on the gun if that is important to you?
Shot rather low in my testing but hop-up and barrel change may fix it.
Almost unusable in Full Auto mode.
The WE M92 GBB Full Auto Airsoft Pistol is one of the nicer looking Airsoft Beretta M9 pistols on the market and is comparable in quality to other higher end brands like KWA and KJWorks. The price point is also in line with what you are getting. I really like the Stainless - Silver - Chrome finish or what ever you want to call it… One thing I was not able to determine 100% is if this version is in fact the Gen 2 version but I do believe it is given that it has the black gas tube in it. We just don’t have it advertised as such. If you’re in the market for a Beretta style M9 Pistol then consider the WE M92 GBB Full Auto Airsoft Pistol as a solid choice.
I haven’t reviewed many WE products over the years as they where not part of our inventory in the Replica Airguns Store. The good news is we do carry a selection of their pistols in our Canada Store including the WE 1039 M92 GBB Full Auto Airsoft Pistol I review in this video along with some 1911’s. In this Field Test Shooting Video I test out the WE 1039 M92 GBB Full Auto Airsoft Pistol in the Replica Airguns Sea Can Indoor Shooting Range to find out what the real world velocity and accuracy is.
Starting with the velocity portion of the test I place 6 rounds through my Chronograph using .25 gram Airsoft BB’s and I averaged 317 fps which is about right considering the claimed fps is 366+ using .20 gram Airsoft BB’s. The temperature was also not overly hot or cold in the Sea Can so in warner shooting conditions the fps will up a bit too.
Next I performed my accuracy test where i generally shoot 10 rounds on a paper target for 30 feet back ling a rested shooting position, sand bag up front and sensated in the back. I found the WE 1039 M92 GBB Full Auto Airsoft Pistol was shooting a good 6-8 inches low at this range with the default hop-up setup so I had to aim near the top of my target to place rounds closer to the bullseye for the sake of the video. I would say the WE 1039 M92 GBB Full Auto Airsoft Pistol is capable of 1-2 inch 10 rod groupings, my test was closer to 2 inches but I can see potential for sub 2 inch groups. A quick hop-up adjustment should bring the aim point closer to where the rounds are actually hitting. I did perform a full auto mag dump and the WE 1039 M92 GBB Full Auto Airsoft Pistol was able to get through all 26 rounds with a full mag of gas but as expected accuracy was not very goo dat all as the heavy blowback action really throws this gun around.
All in all the WE 1039 M92 GBB Full Auto Airsoft Pistol is a really nice Airsoft pistol that performs fairly well and in a game situation would get the job done nicely. It’s also a real looker with it’s stainless looking finish. Keep posted for my Table Top Video I will be making shortly for the WE 1039 M92 GBB Full Auto Airsoft Pistol.
I was hoping this Field Test Shooting Video would go off without a hitch but I did stubble with the laser a bit, I like to shoot guns straight out of the box without really sighting them in but in the case of an add on laser I was expecting to do some sight adjustments. To my surprise when I placed the laser on the Crosman P1 Taurus PT-92 CO2 Blowback Full Auto BB Pistol the laser red dot lined up almost perfectly with the open sights. Sounds great but during my actual test it seems that the heavy blowback action may have nocked the laser sight around placing the laser red dot way to high making the Crosman P1 Taurus PT-92 CO2 Blowback Full Auto BB Pistol shoot really low for this test. I did figure it out via some trial and error and was able to pull off this Field Test Shooting Review in the end for everyone…
Starting with the Chronograph portion of the Field Test Shooting Video, I placed 5 shots through my Chrony and was able to get an average fps of 315. The temperature was not really cold or hot so on a warmer day I would expect around 330 to 340 fps. I did accidentally shoot off around 5 rounds in full auto at the beginning which may have effected the first couple of higher velocity shots that come out when you are using a new CO2 but there results I got I was happy with and give a more realistic velocity fo the Crosman P1 Taurus PT-92 CO2 Blowback Full Auto BB Pistol.
Next I placed 10 rounds into my paper target setup 30 feet down range and did my best to get them on the paper, as mentioned I had to figure out exactly where the laser red dot was pointing in relation to where the BB’s where hitting and once I figured this out I was able to get 10 rounds all within about 2 inches of each other so not bad for a Blowback CO2 BB Pistol. of course the included Laser Sight is adjustable for windage and elevation so I could line up the laser red dot with the actual shot placement which is something you can not do with the non adjustable open sights.
All in all the Crosman P1 Taurus PT-92 CO2 Blowback Full Auto BB Pistol with Laser performed much like all the other KWC PT92 CO2 Blowback Beretta/Taurus type Airguns, the laser red dot simply allows for a more visual and perhaps faster way to place BB’s on your target, at least once you get it sighted in of course!
Type: BB Pistol. Manufacturer: KWC - Distributed by Crosman. Model:P1. Materials: Mostly all metal build. Weight: 2.44 pounds (1107 grams). Barrel: 4.1 inches, brass, non-rifled. Length: 8.75 inches. Propulsion: 12 gram CO2 x 1. Action: Semi & full single and auto, double action trigger. Ammunition Type: 4.5mm BB's. Ammunition Capacity: 20 round full size dropout metal magazine. FPS: 400.
Trigger Pull: The trigger pull on the Crosman P1 Taurus PT-92 CO2 Blowback Full Auto BB Pistol is good in both single and double action. Double action as expected has the longer heavier pull but is still smooth and not too heavy with a predictable release. Single action shooting has a much shorter trigger pull with a slight take-up and even lighter release than in double action mode.
Accuracy: I have not done my shooting Field Test specifically for this Crosman P1 Taurus PT-92 CO2 Blowback Full Auto BB Pistol but I have shot enough of these KWC PT-92 rebranded pistols to know that it should get about a 2 inch 10 shot grouping from 30 feet away in semi auto mode of course. And I expect it to get around 330-340 fps on the Chrono. We will have to wait and see the final results when I get to my performance review.
Build Quality: Like all the KWC full blowback CO2 Airguns, the Crosman P1 Taurus PT-92 CO2 Blowback Full Auto BB Pistol has an overall good build and the design has been out long enough to get any of the bugs worked out by KWC. The fit is good and almost the entire gun is metal so it has great weight to it. Finish wise the electromagnetic coating can wear off in the high spots over time but this is true with real steel blued guns too, it will just happen a bit quicker with the airgun versions.
Realism: Again like the full line of KWC full blowback Pistols, the Crosman P1 Taurus PT-92 CO2 Blowback Full Auto BB Pistol is an amazing replica and looks and functions the part of a real Taurus PT-92 in almost every way including being able to be fully field stripped. You will also find metal working parts in the same places you would find them on the real steal version. only the grips and some internal parts like the gas chamber and nozzle are plastic
Pros:
Pretty much all metal gun with good weight.
Heavy blowback feel.
Nice single and double action trigger.
Semi auto and full auto ready out of the box.
Field strips like the real steel version.
Has been on the market for a while so bugs worked out now.
Nice replica of the Taurus PT-92.
Comes with a laser in the box.
Cons:
Has the ugly white warning instruction on the slide.
Only single white dot on rear sight, would have liked them front and back
Expect to use up CO2 very quickly as is with all KWC full blowback airguns.
Could buy the KWC version and then add your own red dot perhaps for less money?
The Crosman P1 Taurus PT-92 CO2 Blowback Full Auto BB Pistol isn't anything we haven't already seen from KWC or even Crosman for that matter with their PFAM98 (The laser less version) and other Airgun distributers re-branding this same KWC made gun. I do like that the Crosman version is full auto ready out of the box and about their claims of up to 400 fps? Well we will have to see about that as it seems optimist to me based on my other Field Test Shooting Reviews I have done with virtually the same KWC Airguns. The only real unknown going into my Field Test Shooting Review for the Crosman P1 Taurus PT-92 CO2 Blowback Full Auto BB Pistol with be just how well the laser works and if it helps to improve on the accfriay in any way?
I will say right off the bat this Field Test Shooting Video for the Air Venturi 3000 PSI Aluminum HPA Tank with Stock and Adapter did not go as well as I would have wanted it to! The HPA tank itself worked really well but I believe the adapter was faulty as it was destroying the seals on my tank and not regulating very well.
I still wanted to publish this video regardless as not all reviews go as planned, some fail horribly but I would rather be honest and transparent about it rather than have you believe every product is a perfect.
There will always be problems even with really great products there can be defects. I plan to get a new adaptor and try this Field Test Review Video again but for now you can have some fun watching me at least have some success using the Air Venturi 3000 PSI Aluminum HPA Tank with Stock on my Rap4 Rap5 MP5.
You can also watch my Table Top Review Video for more details and info on this product!
I will also be following up my Table Top video with a Field Test Shooting Video to see what possible advantages and disadvantages the Air Venturi 3000 PSI with Stock & Adapter Aluminum Tank has in a real world test of its performance, hopefully all advantages!
Pros:
Compact and is the perfect size to use as a rear buttstock for various 88 Gram and or HPA rifles.
Smaller tank means if you are using a foot pump it won’t take all day to fill up :)
Comes with adapter so can be used with regular HPA and 88 Gram CO2 systems.
Regulated to 1100 psi so should perform better in terms of max velocity and consistency compared to CO2 which is around max 800-900 psi with velocity being effected by cool down.
Not effected by colder temperatures compared to CO2.
Once you have this tank the cost is virtually nothing to shoot compared to expensive 88 Gram CO2 cartages. You just need to buy your pellets or BB’s.
Cons:
Still takes a while to pump up using a foot pump system.
Higher initial cost ($195) than simply buying 88 gram CO2 cartages when you need them.
Will need access to a pump or compressor to use it.
Doesn’t look as good as the supplied buttstock at least with the Sig Sauer MCX and MPX.
Comments:
I guess the question is who is this for? If you are a casual shooter that perhaps owns the Sig MPX or MCX or even another 88 Gram CO2 Air Rifle that the Air Venturi 3000 PSI with Stock & Adapter Aluminum Tank would work with then this may be a bit expensive especially if you don’t have a way to pressurizer the tank at home. On the other hand if you already have a foot pump or air compressor or easy access to one and maybe you have other HPA or CO2 based airguns this tank will work with then it’s kind a no brainer to get it. Maybe you juts want a system that gives you maximum and consistent velocity no matter how cold it is outside. All good reasons to get one in my books.
I thought when I read the one mag instruction guide that I had a good idea on how to use it but there was one area I misunderstood. I thought I needed to pull the tab in and out several times to reload the magazine but in fact I only needed to pull it out once, then shale the magazine back and forth horizontally a few times and then I was good to go.
I also read some other comments that mentioned I didn’t have to take the magazine out every time I reloaded so in this video I test that out to make sure and then one last comment that rather than pulling the charging handle back each time I reloaded I could simply press the bolt release on the right side of the Airgun, and yes this is the case with the Crosman Full Auto rile series.
So here I go a second time in making sure I do it right this time!
I have been wanting to test out the Crosman Full Auto Quick Reload Magazine for a while now and finally got around to it. The weather was cooperating with me so I went outside for this one and setup a bunch of cameras to make the many many magazine reloads a bit more interesting for my viewers.
The Crosman Full Auto Quick Reload Magazine has a hopper that is said to hold around 300 4.5mm Steel BB’s which I can attest it does in fact hold at least 300 BB’s. The Crosman Full Auto Quick Reload Magazine like their regular Crosman Full Auto Magazines holds two 12 gram CO2 Cartridges, so the question is, will I be able to get through most of the 300 BB’s without reloading the CO2?
Watch my struggle a bit to figure out the exactly how to properly use the Crosman Full Auto Quick Reload Magazine and then quickly eat through 300 or so BB’s blasting pop cans down range!
In this Field Test Shooting Video I perform my usual Chronograph and Accuracy tests in the Replica Airguns Indoor Sea Can Shooting Range to find out what the actual feet per second velocity is and how accurate the ICS CPX-APE SF1 AEG Airsoft Rifle is in both semi auto and full auto. Watch my Table Top Video if you are looking for more info on Specifications and Details along with a full tear down of the ICS CPX-APE SF1 AEG Airsoft Rifle.
First up I place 6 rounds through my Chronograph to see what the real world velocity is and the ICS CPX-APE SF1 AEG Airsoft Rifle was able to average 391 fps using .25 gram plastic Airsoft BB’s. ICS claims the ICS CPX-APE SF1 is capable of fps up to 460 fps but this would be using lighter .20 gram Airsoft BB’s which I believe is entirely possible!
Next I put a fresh paper target on my metal backstop 30 feet downrange and proceeded to shoot 10 round in semi auto to see how tight of a grouping I could get. I was happy to see that 7 of my 10 rounds all grouped nicely within the 1.5 inch bullseye and only 3 came out just slightly increasing the grouping to around 2 inches but still closer to 1.5 inches. When I switched over to full auto and emptied the 300 round magazine into the target, amazingly the grouping still seemed to stay pretty close to 2 inches in diameter with some stragglers. The ICS CPX-APE SF1 AEG Airsoft Rifle punched a satisfying hole in my target going through several layers of cardboard.
As you can see in this YouTube Field Test Shooting Video the ICS CPX-APE SF1 AEG Airsoft Rifle performed very well for me living up to its pristine price point. You will pay top dollar for the ICS CPX-APE SF1 AEG Airsoft Rifle but will also get top quality with a ton fo features including an almost all metal/aluminum build, ambidextrous controls throughout, tons of add on capabilities using the 5 sided Keymod hand-gurd, fully adjustable folding stock and exceptional performance.
Type: AEG EBB Airsoft. Manufacturer: ICS Model: CPX-APE SF1 Materials: Mostly Metal/Aluminum. Weight: 6.4 pounds (2900 grams). Length: 25.2 inches folded / 32.5-36.2 unfolded. Hop-up: Yes adjustable. Propulsion: AEG EBB (Electric Blowback). Action: Semi & Full Auto single action only electric trigger. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 300 rounds. FPS: 460 fps.
Trigger Pull: The trigger pull on the ICS CPX-APE SF1 AEG Airsoft Rifle is pretty much like most AEG Electric trigger operated Airsoft Rifles. Usually mid range, light and with no real noticeable release point since it is an electric on and on switch at the end of the day and not really mechanical. Of course you can elect between semi and full auto operation at will.
Accuracy: I have not done my actual Field Test Shooting video review for the ICS CPX-APE SF1 AEG Airsoft Rifle but plan to tackle this video next on my list so this week for sure, stay posted of this one as I have not Field Tested any ICS Airsoft Rifles to date and really don’t know what to expect!
Build Quality: The G&G ICS CPX-APE SF1 AEG Airsoft Rifle is extremely well made as the price tag would suggest. You are going to find metal almost everywhere on this product including the all aluminum upper receiver. The only plastic I could find on the ICS CPX-APE SF1 AEG Airsoft Rifle was in the magazine and the folding butt stock. Everything else is metal/aluminum including the upper and lowe receivers, the sights, the rails and all of the controls. Fit and finish feels great as-well!
Realism: The ICS CPX-APE SF1 AEG Airsoft Rifle is not a replica so to speak of any one particular gun in production but does have some AR and perhaps SCAR attributes to it. Perhaps there needs to be a real steel version of this gun as it does combine a bit of the best of a both platforms. The ICS CPX-APE SF1 AEG Airsoft Rifle is sold for sure with great weigth and feel to it being that it is mostly metal. All the controls work exactly like you would expect on a the real powder burner and you can totally take this Airsoft rifle apart in just a minute or two with virtually no tools.
Mostly metal construction with full aluminum upper receiver.
Tons of rail attachment options with the 5 sided Keymod rail hand-guard.
Fully adjustable pop-up iron sights.
Most everything is ambidextrous: Selector switch, Magazine release, Charging handle, Sling mount.
Rear folding stock has tons of positions, 6 in length and 5 for cheek rest.
Super easy access to everything, hop-up, gear box, inner barrel, outer barrel.
Electric blowback system for slight recoil effect.
T-window in magazine for quick ammunition checks.
FPS is nice and high, great for longer range shooting.
Cons:
On the expensive side but very high quality.
Limited battery options as space for a battery is tight.
May have a bit too high of fps for closer quarter indoor Airsoft games.
Comments:
The ICS CPX-APE SF1 AEG Airsoft Rifle is not an inexpensive product and may be a bit out of touch for Airsofters on a tighter budget. That said it is really well thought out and well built Airsoft product that is ready to go with no real upgrading required. You may want to show on an optical or red dot sigh, perhaps a tac light or fore grip? Nothing you need right away. There really isn’t one thing I can point out that makes this gun so great, it is a combination of everything. when it comes down to it the ICS CPX-APE SF1 AEG Airsoft Rifle kind of has it all going for it. I am looking forward to seeing just how well it performs during my Indoor Field Test. I have high hopes!
This is a bit of a different test than my usual Indoor Field Test Shooting Video I make here in the Replica Airguns indoor shooting range. I don’t test the feet per second with my Chronograph, I don’t test how accurate each gun is shooting in semi auto. Instead this Full Auto BB Rifle comparisons is to find out which Full Auto BB rifle has the highest rate of fire and which one stays on target the best shooting 25 rounds in full auto, all in one burst.
The guns I use of this Full Auto BB Rifle Full Auto Rate of Fire and Accuracy Test are:
