Materials: Mostly metal with some plastic construction.
Weight: 2 pounds (900 grams).
Barrel: 2.25 inches, non-rifled.
Propulsion: 12 gram CO2.
Action: Revolver, single & double actions.
Ammunition Type: 4.5mm steel BB's.
Ammunition Capacity: 6 rounds.
FPS: 328 fps (120 m/s).
Trigger Pull: The trigger pull on the Gletcher CLT-B25 357 2.5 Inch CO2 BB Revolver is good in both single and double action, even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, most likely because the spring tension that pushes the inner barrel to make contact with the cylinder is noticeably lighter on the KWC - Gletcher 357's. Even the hammer is smoother and has less wiggle, just a better trigger and hammer mechanism overall.
Accuracy: In terms of power and accuracy, you can checkout my full Field Test Shooting Video here. I did get a nice 2 inch 6 shot grouping on my paper target setup 30 feet away from my standard semi-rested position (sand bag up front and standing in the back). Accuracy was a bit lower than the factory claimed 320 or so fps coming in at an average of 280. I did perform my field test back in May so the weather was not all that warm perhaps effecting peek fps performance somewhat.
Build Quality: The Gletcher CLT-B25 357 2.5 Inch CO2 BB Revolver being mostly metal has a very good build quality, perhaps even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, even the weight of the KWC 357 is noticeably more! The only real plastic or rubber I could find was in the grips and the shell tips. Fit and finish was also good with no noticeable wear or sloppy workmanship.
Realism: The KWC - Gletcher CLT-B25 357 2.5 Inch CO2 BB Revolver overall is a close copy a the real steel 357 styled revolver. I did notice the rear portion of the receiver (between the rear cylinder and hammer) to be a bit longer perhaps to accommodate the CO2 valve length, but other than that this pistol is super close to the original 357 styled revolver it is based on. Again being all metal gives this CO2 BB revolver very realistic weight and feel and the loadable brass shells make using this gun almost exactly like using a real shell loading revolver but for much less cost per shot and of course a lot less recoil on the hands that a real 357 magnum or even when shooting 38 special shells for that matter.
It's a revolver with actual shells! Give you the feeling of loading and shooting a real revolver
Mostly all metal design
lots of detail, well made, fit and finish are both good.
Good overall weight, even for this short 2.5 inch barrel version.
Fully adjustable rear sight for windage and elevation.
Well hidden CO2 Screw.
Recessed barrel.
Nice Trigger pull in both single and double action.
Tactical fingered grips look good and allow for a firm hold.
Cons:
Grips are a bit rough, not as rubbery as they look.
Grips may be a bit large for people with smaller hands.
All black sights not great on dark backgrounds.
FPS could be a bit higher!
Comments:
The Gletcher - KWC CLT-B25 357 2.5 Inch CO2 BB Revolver is yet another addition to the increasing lineup of shell loading revolvers available today in both Steel BB and Airsoft versions. The 2.5 inch reviewed here is meant to be the compact version with its snub nosed barrel but I would have to say it is not a small gun at all coming in at 2 pounds and with rather large grips and a pretty large cylinder to pack around. But then again, that may be just what you are looking for? The shorter barrel does effect the fps performance since longer barreled versions of this same pistol I have tested do shoot much hotter but that is to be expected with pretty much any short barrelled CO2 pistol.
My Vimeo Table Top Review for the Gletcher CLT-B25 357 2.5 Inch CO2 BB Revolver:
In this Field Test Shooting video I test out the performance of the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol using my Chronograph to get a real world (FPS) Feet Per Second rating. I also position myself 30 feet back and shoot 10 rounds at a paper target using a semi-rested shooting position (Sand bag up front and standing in the back).
In terms of velocity the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol shot a bit on the fast side at 414 FPS when averaging a 5 shot strong using .20 gram BB's with a brand new CO2. Keep in mind I was using the CO2 magazine which will have more power than the Gas Magazine version. I would assume the Gas mag version would shoot right around the mid 300's which may be more suited for indoor Airsoft games. For outside Airsoft wars you may want the extra power of the CO2 mag for shooting at targets further distances out.
Stepping back 30 feet and shooting at my paper target, the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol produced a decent 2 inch 10 shot grouping that was just a hair low but well centered left and right. The low factor could be adjusted up using some Hop-up tweaking. The trigger in single action mode is light and the release is crisp. Even the double action trigger is fairly light for double action, but there is a lot more take up since your finger is doing all the work that the blowback action would normally do for you when shooting in single action.
With the heavy blowback and high FPS the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol creates a really great shooting experience. It would be great for some target practice, getting some additional trigger time in if you are a Sig Sauer P226 owner and would make an excellent outdoor Airsfot war backup weapon. The quality is excellent and as a lover of the Sig Sauer lineup of guns I highly recommend this Airsoft pistol from KJWorks.
Here is my follow up Shooting Field Test video for my Cybergun Colt 1911 MKIV CO2 Table Top Review. During this Field Test Shooting video review I shoot 5 rounds of .20 gram Airsoft BB's through my Chronograph to find out the average FPS. I also step back 30 feet and setup my shooting stance by resting my hands on a sand bag and standing in the back for a fairly secure shooting position. As per most of my accuracy tests, I loaded my Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol with 10 rounds in the magazine to see what kind of grouping I could get on the paper target..
I was a bit surprised by the FPS for the Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol I tested. The claimed FPS by the factory is 360 using .20 gram BB's, the temperature outside was decently warm and I was using a brand new CO2 so I should have gotten fairly close the this velocity. As it turned out on this day the gun I was testing shot right around 300 FPS which is great for close quarters Airsoft games but perhaps a bit weak for the longer ranges of outside games.
When it came to accuracy, I did find the Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol shot a bit high and to the left right out of the box but since it has a fully adjustable trigger this did not concern me. I was pleased to see that I was able to get a 2 inch 10 shot grouping from 30 feet back using a semi rested position which is about right for an Airsoft Pistol at this range.
While testing the Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol I did not have nay mechanical problems, everything worked exactly as it was meant to , the Blowback was nice and crisp with that usually 1911 sluggishness I have come to expect. The trigger is pretty typical for a single action 1911 styled trigger which in some cases can actually be a little bit on the light side which with the Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol was not the case. Over all a really pleasurable Airsoft Pistol to shoot!
Ammunition Capacity: 19 round full size metal magazine.
FPS: 361 using .20 gram BB's.
Trigger Pull: The trigger pull on the Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol is exactly what you would expect from a true single action 1911 styled pistol. It has a short take up and then a nice light and crisp release. The working grip safety is a nice touch requiring your palm to be pressed against it for the trigger and hammer to operate. I also like the Tactical Style Trigger found on the Cybergun Colt 1911 MKIV.
Accuracy: At this point I have not shot the Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol, I imagine it should perform well considering it has spin-up up and a fully adjustable rear sight just in case my shooting is off center a bit. According to the manufacturers claimed fps, we should get somewhere in the mid to high 300 fps range using .20 gram Plastic Airsoft BB's.
Build Quality: I am kind of sitting on the fence with the Colt 1911 MKIV Pistol, on one hand it is an all metal gun with what looks to be fairly decent fit and finish but on the other hand it feels kind of light weight especially with the heavy magazine out of it compared to even the KWC 1911's I have reviewed so often. It may be that more aluminum is being used in this pistol which could actually be a good thing since aluminum would be a higher quality metal over your typical zinc alloy used in most Airsoft and Airguns these days. In terms of operation, I feel like some of the mechanical parts need a bit of break in time, but I have found this to be true with many real guns I have used.
Realism: The Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol is a close replica of the real steel Colt 1911 45 auto but with a more modern Tactical look to it, sporting a Tac style trigger and hammer, double stack magazine, ambidextrous safety and adjustable rear sight. This gun is nearly all metal with very full blowback operation making it feel real to hold in the hand and shoot.
True 1911 single action trigger, excellent pull, very smooth and light.
Accurate trigger design and working grip safety.
Double stack metal magazine holds the CO2 and extra BB’s.
Fully Colt Licensed.
Full adjustable rear sight.
Tactical trigger and hammer with ambidextrous trigger for a more modern look and feel.
Cons:
Comes with the ugly red tip that is really stuck on the gun.
Can kind of tell the Chinese quality a bit.
Licensing is not engraved right into the gun.
Comments:
Overall the Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol is another nice option if you're looking for a Colt Government 1911 Styled Airsoft pistol. Keep in mind this one is Chinese made rather than made in Taiwan. Not sure how that will effect performance and longevity. I have owned Chinese guns that have shot and faired well for me so I am not too worried about it. With its double stack magazine you will find the Cybergun Colt 1911 MKIV to have a fairly large handle so it may not be suitable for those with smaller hands. I do think the Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol features a nice combination of classic Government 1911 looks with a few modern tactical components lie the upgraded trigger, hammer, ambidextrous safety and rear adjustable sight.
My Vimeo Video Review for the Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol:
Trigger Pull: The trigger pull on the KJWorks KP01-E2 Sig Sauer P226 Airsoft Replica is good in both single and double action. Once the slide is pulled back and released the first round is chambered and the hammer will remain back placing the KJWorks P226 in single action mode, the pull is light and the take-up is nice and short, most of your shots will be in single action mode unless you use the de-cocker to lower the hammer for a subsequent double action follow-up shot, double action shots are still pretty light but much longer in order to cock the hammer back.
Accuracy: (I have not shot the KJWorks distributed CO2 Mag version but I have already done a Field Test Shootinng Review for the same KJWORKS gun distributed and licensed by Cybergun in the Gas Mag version. Here is what I had to say about the Cybergun Gas Magazine version: "Shooting the Cybergun Sig P226 from 20 feet out in semi rested position I was able to get very good results. I placed 10 rounds in about 1.5 inches with the shot placement being a bit low possibly due to my barrel mod, adjusting the hop-up may bring the aim point back up to where it should be. The Sig Sauer P226 Airsoft Replica shot right around the 316 fps range while conducting my 5 shot average chrony testing which was lower than advertised but I was using much heavier .20 gram BB's. You can expect to get a full magazine worth of shots out of each gas fill-up but I did notice that as the magazine got colder it did tend to become much less efficient and also seemed to vent a lot of vapor."
Build Quality: The build quality for all KJWorks guns in my opinion is one of the best in the business. Fit and finish is top notch with close tolerances in the working parts as you would find in a real steel gun. The paint is excellent and in general will wear much better than other Airsoft guns out there. The KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol is pretty much all metal and feels it, the recoil spring is nice and firm and all working parts are smooth and crisp when operated.
Realism: The KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol is a replica of the real steel Sig Sauer P226 with the exception of the licensing. The KJWorks KP01-E2 really is a great looking and functioning Airsoft Replica. You can field strip this gun exactly like a real Sig Sauer and all the mechanical parts work just the same including a working de-cocker and adjustable front sight. It is really hard to distinguish the Airsoft version from the real Sig P226 in both looks and feel.
All metal pistol with good overall realistic weight to it.
Very crisp and firm full blowback operation.
Some of the best fit and finish in the industry. Especially in price range.
Nice accurate looking and working Sig Sauer P226 Replica.
Working de-cocker.
White dot sights for quick target acquisition.
Front sight is adjustable for windage.
Full size drop out magazine holds Airsoft BB's and CO2.
Fully field strip-able.
Cons:
No actual Sig Sauer Licensing but very clean look.
CO2 Mag does stick out a bit and add to size
Comments:
I am a huge Sig Sauer fan so I have kind of high expectations with a replica gun! The KJWorks lineup as a whole is really fantastic, and what I say about the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol can be said about the entire lineup. KJWorks makes a super well built product that replicates the real steal version almost exactly other then they shoot Airsoft BB's instead of actual bullets. When holding a KJWorks gun in the hand you can feel the quality, in weight, ballence and especially when operating the slide, trigger and other working parts. Everything just feels so perfect and responsive. For the money you can not go wrong with the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol or any other KJWorks gun for that matter.
My Vimeo Table Top Review of the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol:
Ammunition Capacity: 19 round metal stick drop out universal magazine.
FPS: 394 fps 120 m/s.
Trigger Pull: The trigger pull on the Gletcher BRT 84 is rather long and a bit on the heavy side but it is smooth and predictable. The release point takes a while to get to but once you figure it out you can get really accurate shot placement with this Beretta Model 84 replica. As with many low cost simplicity designed CO2 Air Pistols, the Gletcher BRT 84 uses the barrel like a hammer. When you pull the trigger, the inner barrel moves forward and out of the outer barrel allowing a BB to move into the breach area, then the barrel snaps rearward hitting the CO2 valve releasing CO2 and shooting the BB.
Accuracy: I tested the Gletcher BRT 84 All Metal CO2 BB Pistol from 30 feet back shooting at a paper target using a semi rested position I was able to get a near 1 inch 10 shot grouping on two separate occasions with this rather small and unassuming airgun. In terms of feet per second performance the Gletcher BRT 84 All Metal CO2 BB Pistol is rated at 394 fps, my Chronograph results shooting 5 rounds through the Chrony using a full CO2 and 5.1 grain Steel BB's was a respectable 421 fps, even a bit higher then the factor claim of 394.
Build Quality: Being a pretty much all metal gun, makes the Gletcher BRT 84 All Metal CO2 BB Pistol feel solid and sturdy even for such a small pistol. The only plastic parts on the Gletcher BRT 84 are the grips, the CO2 tab and perhaps an internal part like seals and such. The painted finish is a nice dark grey and seems to be wearing really well. Since the Gletcher BRT 84 All Metal CO2 BB Pistol is basically a one piece solid metal moulded airgun, there is really nothing to go wrong and no fit problems to speak of. Yes it is basic but it is also really well made.
Realism: The Gletcher BRT 84 All Metal CO2 BB Pistol is a replica of the real steel Beretta Model 84. It is an extremely close copy in terms of looks and feel, but does not have very many moving parts other than the trigger, magazine release and safety. So no slide movement or blowback, no working slide catch release, not even the hammer is functional. That said, not much to go wrong if what you are looking for is a gun that looks like a Beretta model 84.
Very solid all metal construction, good weight and feel.
Stick magazine is universal and can be used in many other guns.
Very accurate with good fps performance.
Grips feel nice, almost have a rubber like texture.
Simple design so not very much to go wrong with this airgun.
CO2 tab is hidden internally.
Reasonable price tag for well built all metal airgun.
Cons:
Very few working parts.
Trigger is a bit long and heavy, not ideal for action shooting.
Sights are non-adjustable
No Beretta Licensing
Comments:
I am usually not a huge fan of non-blowback basic airguns, especially when they do not have many working parts on them. However the Gletcher BRT 84 All Metal CO2 BB Pistol has some strong points that makes it worth considering, like it's solid all metal build, excellent accuracy and nice high fps performance for such a small sized airgun. It all feels really good in the hand ergonomically and based on the way it's built in such a simple no frills manner, the Gletcher BRT 84 All Metal CO2 BB Pistol should last a long time if taken care of.
Watch my Vimeo Review for the Gletcher BRT 84 All Metal CO2 BB Pistol:
Action: Semi auto non-blowback, double action only.
Ammunition Type: Airsoft plastic 6mm.
Magazine Capacity: 15 rounds
FPS: ? (1.6 Joules)
Trigger Pull: The trigger pull on the KWC Model 1911 All Metal Non-Blowback CO2 Airsoft Pistol was about medium to hard but I have definitely experienced heavier trigger pulls on many double action only Airguns. It is nice that the trigger has the look of a 1911 and not your typical lever styled trigger. I did find the trigger to be very usable and the release point is smooth and fairly predictable.
Accuracy: I have yet to perform my field test shooting component for the KWC Model 1911 All Metal Non-Blowback CO2 Airsoft Pistol, however I have reviewed the same gun in 4.5mm Steel BB Cybergun version and here is what I had to say about that the Steel BB version: "Accuracy was decent but not outstanding, I got around a 2.5 inch grouping from a 20 foot away free standing position, shooting just to the left and high on the target. I did find that I was able to zone in a bit better with the Cybergun GSR 1911 as I got used to the trigger. I also put the Cybergun Sig Sauer GSR through my Chrony Chronograph and got very close the manufacturers 397 claimed feet per second, actually starting off well above it and settling down to around the 370 FPS mark. My 8 shot average on a new CO2 was actually 422 FPS."
Build Quality: The build quality for the KWC Model 1911 is very good, this is an almost all metal Airsoft gun with a few exceptions like the hammer, trigger. magazine release, slide catch and grip safety. Pretty much everything else is metal including the slide, frame, magazine, and even the grips. The finish is very good and since there is lots of metal with minimal moving parts and less to go wrong, this should make for a very reliable pistol.
Realism: The KWC Model 1911 CO2 Airsoft Pistol is very close to the look, weight, and feel of the real steal Sig-Arms 1911 GSR! Even the 1911 style trigger was replicated as best as it could be given it being double action only. It would have been nice to have a single action trigger and a working slide to finish off the illusion but overall the GSR is a really nice copy of the real steel Sig Sauer GSR Sig-Arms 1911 firearm.
Very Accurate Sig-Arms Sig Sauer 1911 GSR Replica.
Should have good FPS and lots of shots per CO2 based on my 4.5mm BB version testing!
Very affordable and good value for the money.
Rail for mounting accessories.
Nice sights with white dots front and back.
Recessed barrel for added realism.
True 1911 style trigger even though it is double action only.
Very affordable price tag.
Cons:
Non-blowback and the slide does not move either.
The hammer is only for show and does not cock for single action shots.
Trigger action is bit heavy but not not too bad for a double action trigger.
Non adjustable rear sights.
Comments:
For a relatively inexpensive All Metal Airsoft gun you get a lot for your money with the KWC Model 1911, most importantly a very accurate reproduction of the real steal Sig-Arms Sig Sauer 1911 GSR firearm! If you're a 1911 fan and want to pick up an Airsoft gun that won't set you back too much, then the KWC Model 1911 would make a great choice with it's heavy full metal weight, full size drop out metal magazine, accurate reproduction of the real steal Sig-Arms GSR and again that very affordable price tag.
My Vimeo Videos for the KWC Model 1911 CO2 Airsoft Pistol:
This First Person Shooting Clay Pigeons Video with my KJWorks M9A1 and 1911 Airsoft Pistol is to serve two purposes: Number one and really the only reason needed to make a video like this... To get outside on a nice warm summer day and practice some tactile shooting all while recording it in first person so you can come along and enjoy it with me :)
Secondly I wanted to inform everyone that the video uploads will be a bit lighter for the next week or so since I am on what I call a working holiday. I am focusing on a Fitness Contest this weekend along with a Fitness Expo the following weekend, nothing to do with Replica Airguns but it does coincide with my other Website and YouTube channelGetFitOver40.com. The Fitness contest is the Victoria Cup where I will be competing in the Men's Physique (Masters - Over 40) and (Open - All Ages) divisions. The Fitness Expo is called "theFitExpo" and it is in Anaheim California.
So if you want to watch more of my videos then you will have to checkout my other fitness channel for the next week where I will be posting lots of related content on what's going on fitness wise in my life right now.
Trigger Pull: The trigger pull on the KJWorks Beretta M9 & M9A1 is very good in both single and double action. Double action is a bit longer and heavier than when shooting in single action but not heavy by any means. Single action shooting is short, light and crisp as you would expect when shooting a real steel Beretta 92 style pistol.
Accuracy: I have not done my actual Field Test Shooting video review for the KJWorks M9 and M9A1 Airsoft pistols but I did get the chance to make a short preview video where I shot both guns at some clay pigeons setup around 20 feet away. I was able to pop the center out of the clay pigeons no problem and found that even without any practice I was consistently hitting dead center on most shots. I am not sure exactly what the FPS will be but considering both theses versions of the KJWorks M9 & M9A1 have the CO2 mags they should shoot up into the 360+ fps range using .20 gram Airsoft BB's. Blowback operation is strong and the slides cycle full length. Keep posted for my upcoming Field Test Shooting Video for both pistols.
Build Quality: As expected, the KJWorks M9 & M9A1 build quality is just like all the other KJWorks Airsoft guns I've tested so far, excellent the fit and finish is the best in my opinion even when compared to my my 4.5mm steel BB shooters. When using these guns regularly, areas that are painted like the metal friction areas show very light wear which is rarely the case with metal built blowback Airguns. Again the tolerances between the moving parts like the slide and frame are very tight showing excellent workmanship and machining from KJWorks.
Realism: Both the KJWorks M9 & M9A1 are copies of the real steel popular Beretta M9 & M9A1, it is really hard to tell them apart from the real versions. Both the M9 and M9A1 are very similar in design with the M9A1 having some slight cosmetic differences, the biggest being the addition of a tactical rail built into the frame. Both KJWorks Beretta's can be field stripped in the same manor as a real Beretta M9 Semi Auto pistol and all parts function the same.
Pretty much all metal pistols with good weight to them.
Full heavy blowback operation.
Excellent fit and finish as always with KJWorks pistols.
High capacity full size drop out magazine that holds the Airsoft BB’s and CO2. (Can get Green Gas mags)
Seem to be very accuracy and well centered on target.
White dot sights make it easy to shoot an most backgrounds.
Ambidextrous safeties.
Field strip-able like the real steel versions.
Cons:
Sight are non-adjustable but elevation can be adjusted using the hop-up.
Grips may be a bit wide for some small handed people.
CO2 magazines sticks out a bit when using the CO2 mags.
Comments: The KJWorks Full Metal M9 & M9A1 are yet more examples of excellent full blowback Airsoft pistols from KJWorks. They are built to very high standards, are near perfect replicas of the real steel Beretta M9 & M9A1 and performance is also excellent. Yes the price is slightly higher than a similar Airsoft gun from KWC but the quality on the KJWorks is definitely worth the extra cost. Make sure to drop by our Replica Airguns Canada Store and checkout our new lower pricing on the KJWorks line of Airsoft guns.
My YouTube Table Top Review of the KJWorks M9and M9A1 Full Metal Blowback Airsoft Pistol:
Trigger Pull: The trigger pull on the KJWorks 1911 is very good since it is modeled after a real steel 1911 which makes it short and crisp with a very light trigger pull. There is a very slight take-up at the very beginning of the pull but once your get past this the release is crisp and perceptible. Since it is not a double action trigger you will need to either rack the slide for your first shot or pull the hammer back if you have already chambered a round.
Accuracy: I have not done my actual Field Test Shooting video review for the KJWorks 1911 Airsoft Pistol but I did get the chance to make a short preview video where I shot some clay pigeons setup around 20 feet away. The KJWorks Full Metal CO2 Airsoft 1911 was a lot of fun to shoot at the clay pigeons and I had no trouble hitting them form that range over and over again. I am not sure exactly what the FPS will be but considering this version of the KJWorks 1911 has the CO2 mag it should shoot up into the 360+ fps range using .20 gram Airsoft BB's. Blowback operation is strong and the slide cycles full length. Keep posted for my upcoming Field Test Shooting Video for the KJWorks Full Metal 1911 CO2 Airsoft Pistol.
Build Quality: As expected, the KJWorks 1911 build quality is just like all the other KJWorks Airsoft guns I've tested so far, excellent the fit and finish is the best in my opinion even when compared to any of my 4.5mm steel BB shooters or 6 mm Airsoft pistols. When using KJWorks guns regularly, areas that are painted like the metal friction areas and high spots show very light wear which is rarely the case with metal built blowback Airguns. Again the tolerances between the moving parts like the slide and frame are extremely tight showing excellent workmanship and machining from KJWorks.
Realism: The KJWorks CO2 Full Metal 1911 Blowback Airsoft Pistol copies the real steel very popular even today Colt 1911 A1, it is really hard to tell the KJWorks Airsoft 1911 apart from the real 45 caliber version. The KJWorks 1911 can be field stripped very similarly to a real 1911 Semi Auto pistol and all parts function virtually the same including a working safety, grip safety, slide catch-release, magazine release and hammer.
Pretty much all metal pistol with good realistic weight to it.
Full cycle heavy blowback operation.
Excellent fit and finish as always with KJWorks pistols.
High capacity 28 round full size drop out magazine that holds the Airsoft BB’s and CO2. (Can get Green Gas mags)
Seems to be accurate and well centered on target.
Nice two tone finish.
Working grip safety.
Nice light true single action only trigger.
Field strip-able.
Cons:
Sights are non-adjustable but you can adjust elevation using the hop-up.
Field strips a little different than a real 1911.
CO2 magazine sticks out a bit but KJWorks makes Gas Mags also.
Comments:
I am a big fan of 1911 pistols and love getting my hands on pretty much any version weather it be a Real Steel 45 caliber 1911, a 4.5mm Steel BB version or 6mm Airsoft Pistol. As long as it has that true 1911 single action short light trigger to it. I love the way the slide cycles a bit slower than most semi auto pistols and this can be found in many Airgun and Airsoft version like this KJWorks 1911 making the shooting experience even more realistic. The fit, Finish and overall quality of the KJWorks 1911 over other brands is worth the slight additional costs so if you don't mind paying juts a tad bit more for that extra quality and you're looking for a CO2 1911 then you will not be disappointed with the KJWorks Full Metal CO2 Airsoft 1911.
My Vimeo Table Top Review of the KJWorks M9and M9A1 Full Metal Blowback Airsoft Pistol:
We recently received some new pistols from KJWorks, The CO2 versions in Full Metal of the Colt 1911, the Berretta M9 and the Berretta M9A1. All of these guns are really well made, the fit and finish is excellent. Definitely a very high quality Airsoft pistol and worth spending a little bit more to get this extra quality. We have even lowered the price on many of our new KJWorks guns to make them even more affordable so check them out in our Canada Replica Airguns Store!
So I made a quick demo preview video where I get away from my table top and go outside to show them off a bit and shoot a few rounds through them at some clay pigeons. I did have some camera issues but you will get a good idea on how these guns look and perform.
Materials: Plastic (polymer) and some metal construction.
Weight: 2.7 pounds (1200 grams).
Length: 27.5 inches (700mm).
Propulsion: Spring.
Action: Pump.
Ammunition Type: 6mm Airsoft BB's
Ammunition Capacity: 30 shots per shell.
FPS: 280 (3 shot burst) using .20 gram BB's.
Trigger Pull: The trigger pull on the ASG Franchi SAS 12 feels a bit heavy at first, but since this is not a rapid fire Airsoft gun and needs to be pumped between shots, your finger does not get tired and you will only get 10 shots (3 shot bursts each) off between reloading another full shell. That said the takeup is rather short and the release is predictable once you get used to it being a bit on the heavy side.
Accuracy: Keeping in mind that the ASG Franchi SAS 12 Spring Powered Airsoft Shotgun is in fact a "Shotgun", I did not expect to get sniper rifle accuracy from it and in fact I wanted the three burst rounds to spread out just a bit, similar to how a real shotgun blast would perform. I was very happy with the overall accuracy and spread I got when shooting from 30 feet out in a free standing position.I simple used the open iron sights and all the rounds seemed to center well and spread out just enough to get good coverage on my paper target. In terms of Feet Per Second performance I was not sure what ot expect since three .20 gram BB's where being shot out all at once. I was very happy to see consistent 280 fps velocities which was actually a bit more than I expected considering .60 grams of Airsoft BB's are being shot out with each shot.
Build Quality: This is an almost all external polymer Airsoft Shotgun with the excepting of the outer and inner barrel and a few other parts like the ring mounts, loading bay door and perhaps a few more internal parts being made out of metals. Overall the ASG Franchi SAS 12 feels solid but a bit on the lighter side. I would of liked to have seen more metal parts to perhaps get the weight up a bit but being that the ASG Franchi SAS 12 Short Barreled Airsoft Shotgun is on the light side makes it a great choice as a backup gun that you could easily sling over your back and not be bothered by it all that much.
Good accuracy and fps performance. BB's spread out just right
Light weight and short so great for packing around in tight quarters.
Full Metal Barrel Assembly.
No need for batteries or gas, just load with BB’s and away you go!
Comes with speed loader, extra shell, jam rod and sling strap.
Can also get it with a full stock.
Cons:
May get a bit tiring on the arm after a lot of repetitive shooting.
Would of been nice to include a few more extra shells.
Sights are none adjustable but it centered well for me
Trigger is a bit on the heavy side.
Comments:
The ASG Franchi SAS 12 Short Barreled Airsoft Shotgun is a super fun low cost Airsoft Pump Action Spring Powered Shotgun that shoots pretty hard considering it blast three rounds at a time and the Airsoft BB's hit their mark every time! It's light enough to use in most close quarter combat situations or even strap on your back as a secondary backup weapon. The best part is all you need is a bag of Airsoft BB's and you can shoot all day long, no need for batteries or gas.
Watch my Vimeo Table Top Review of the ASG Franchi SAS 12 Short Barreled Airsoft Shotgun:
Model: M16A4 with Heavy BRRS (Bolt Recoil Shock System).
Materials: Metal & Nylon.
Weight: 7.7 pounds (3500 grams).
Length: 43 inches (1100mm).
Propulsion: AEG with Heavy BRSS
Action: Semi/full auto, single action.
Ammunition Type: 6mm Plastic Airsoft BB (recommend using undersized BB's).
Ammunition Capacity: 300+ round magazine.
FPS: 360+.
Trigger Pull: The trigger pull on the BOLT Airsoft M16A4 is fairly short and light as it is essentially just an on off switch for the internal electronic components. You can shoot this gun very quickly in semi auto mode, and of course in full auto when full auto position is selected. As is with all AEG rifles there is a bit of a delay while the spring is retracted and released, this is not as noticeable in full auto mode and also when using higher voltage 11.1 volt batteries.
Accuracy: I tested the BOLT M16A4 BRSS Airsoft rifle first on my Chronograph to see what kind of real world fps I would get from it using .20 gram Airsfot BB's. The BOLT M16A4 produced consistent 350 fps shots which is perfect for indoor or outdoor Airsoft events. I then stepped back roughly 30 feet and place 10 rounds on my paper target using a semi rested position and was able to get a nice tight 2 inch grouping. When switching up to full auto mode the grouping pretty much stayed exactly the same, right in that 2 inch pocket.
Build Quality: The Bolt M16A4 AEG Blowback Airsoft Rifle is very well made with a full Metal upper and lower receiver, along with metal and polymer parts exactly where they would be on the real steel version of an actual M16 or AR styled riffle. The only rubber or nylon components are the stock and the grips and perhaps some internal parts. I really could not find anything to complain about other than making sure to use the right sized ammo as the barrel is a true 6mm barrel and so when using actual 6mm BB's they can get jammed up. I had great results when I used 5.95mm Airsfot BB's.
Realism: As with many Airsoft guns, there is great attention to realism and the Bolt Airsoft BRSS M16A4 AEG is another great example of an Airsoft rifle based on the Colt M4 platform. It is an AEG but because of the Heavy BRSS (Bolt Recoil Shock System) you get a very nice compromise between a conventional AEG and a GBB (Gas Blow Back Airsoft) gun. In other words, like a standard AEG I get that endless stream of consistent BB's flying down range on target but unlike a true Gas Blow Back Airsoft gun, I don't get that drop off in power and limitation to about 30 usable rounds per magazine. What I do get similar to a GBB is that recoil action that helps make the shooting experience so much more believable! Even the sound from the Bolt M16A4 is much snapper than a standard AEG and more like a GBB. I also like the fact that the charging handle and forward assist work similarly to a real AR and also the dust cover cleverly exposes the bolt and internal hop-up for easy adjustment along with the bolt cycling just like a GBB rifle would cycle which is similar to a real steel AR.
Pros:
AEG Performance with GBB like Recoil.
Very high quality materials and workmanship throughout.
Lots of forward rails to place accessories on and just looks cool in general.
The fixed classic M16 stock is very comfortable and grows on you over time.
Can shorten the gun by removing the barrel extension if you like.
Can use 11.1V Li-Po or 9.6V Ni-mh or Ni-Cd batteries.
Fully Adjustable Hop-up.
Semi and Full Auto.
Cons:
BRSS system will drain the batteries faster than a standard AEG.
Can not switch out the stock as the BRSS system extends back into it.
Need to use undersized 6mm Airsoft BB’s because of the tight barrel.
Comments:
The BOLT M16A4 AEG Blowback Airsoft Rifle with BRSS Recoil is a great compromise for the avid Airsofter looking for a practical skirmish weapon, but also craving the realistic experience of having blowback with recoil similar to a Gas Blow Back systems. I really like this concept and find it great fun to shoot even if its just for plinking in the yard. The overall quality is very excellent and you just have to love the AR platform it's based on. If you're into customizing you can mix and match many external and internal parts with other existing Airsoft mechanical parts and I would imagine real steel accessories. It's great to be able to use an Airsoft rifle in virtually any weather condition and still get that Gas Blowback Feel but with AEG performance and consistency.
My Vimeo Video Review for the Bolt M16A4 AEG Blowback Airsoft Rifle with BRSS Recoil:
My first impressions with the Bolt M16A4 AEG Blowback Airsoft Rifle where not so good as it was miss feeding and miss firing terribly for me. A quick communication with BOLT Airsoft and I was informed that perhpas my BB choice was the wrong one. The Bolt M16A4 AEG Blowback Airsoft Rifle has a true 6mm barrel so it is a tight fit with BB's that are 6mm since many can actually be a bit larger making them get stuck in the breach area.
BOLT Airsoft suggested I switch my Airsfot BB choice to a slightly under sized 6mm Airsfot BB so I tried some of my 5.95mm Airsoft BB's and all I can say is it was like shooting a different gun. Not only did it feed and shoot perfectly, but the Bolt M16A4 AEG Blowback Airsoft Rifle with Heavy BRSS Recoil also became instantly more accurate for me. The moral of this story is always make sure to use the right ammo in your gun :)
So getting back to my Field Test Shooting Review for the Bolt M16A4 AEG Blowback Airsoft Rifle with BRSS Heavy Recoil... In this video Field Test Review I shoot several rounds through my Chronograph to test out the fps velocity of the Bolt M16A4 AEG Blowback Airsoft Rifle. Which by the way came in around the mid 300's. I also step back 30 feet and shoot some semi auto rounds into a paper target to see how accurate the Bolt M16A4 AEG Blowback Airsoft Rifle is. Since the Bolt M16A4 AEG Blowback Airsoft Rifle is a semi and full auto AEG Airsoft rifle, I also had to replicate my accuracy in full auto to see if my groupings would stay consistent even at a high rate of fire. I was very impressed with the accuracy in both semi and full auto, form 30 feet out you will get within 2 inches all day long.
It is fair to note that I was using 11.1 volt Li-po batteries with .20 gram BB's for the entire testing so this did effect my motor speed giving me quicker trigger response and faster full auto rate of fire. I would suggest using a high capacity battery setup since the BRSS Heavy Recoil does use up some additional battery power but boy is it worth it. The BRSS Recoil is not going to be as heavy as a true gas blowback system but it is close and does give you a nice shoulder tap but with the benefit of high capacity AEG magazines and consistent AEG performance.
In a nutshell, if you want the dependability, consistency and none stop shooting performance of an AEG Airsoft AM16 but with the blowback action of a gas system then make sure to give the Bolt M16A4 AEG Blowback Airsoft Rifle with BRSS Heavy Recoil a good look into.
A while back, BOLT was kind enough to send me one of their B.R.S.S. Recoil AEG Airsoft Rifles for review, make sure to watch my full review of the BOLT B4A1 BRSS Recoil Blowback AEG Airsoft Rifle.
Well again BOLT came through and sent me their latest offering, the BOLT AEG M16A4 Blowback Airsoft Rifle with B.R.S.S. Heavy Recoil system. B.R.S.S. stands for BOLT Recoil Shock System. The new BOLT Heavy Recoil system has a fixed stock which houses the improved recoil unit giving a more direct and solid recoil effect to the users shoulder. The BOLT M16A4 is a long length AEG Blowback Airsoft Rifle also suitable for snipers.
Here are some of the specifications:
Blowback B.R.R.S Heavy
Adjustable Hop-up
Semi & Full Auto
Standard AR 70 & 300 round magazines
312 fps & 393 fps versions
Aluminum, ABS, Nylon & Glass Fiber and Steel construction.
7.4V & 11.1V (Li-Po) or 9.6V (Ni-mh / Ni-Cd)
7.7 pounds (3500 grams)
43 inches long (1100mm)
Comes in Black / Tan
In this YouTube Preview video for the BOLT M16A4 AEG Blowback Airsoft Rifle I show you around the gun a bit and do a quick shooting test. Unfortunately I was using 6mm Airsoft BB's which I later found out where a bit to large in diameter since the BOLT M16A4 AEG Blowback Airsoft Rifle has a true 6mm barrel. After the video when I received this information from BOLT I switched to 5.95mm Airsoft BB's and the BOLT M16A4 AEG Blowback Airsoft Rifle worked perfectly for me :)
Stay tuned for my Full Table Top and Field Test Shooting videos for the BOLT M16A4 AEG Blowback Airsoft Rifle:
Action: Semi auto non-blowback, double action only.
Ammunition Type: Airsoft Plastic 6mm BB's.
Ammunition Capacity: 15 rounds
FPS: 400+
Trigger Pull: The trigger pull on the KWC IWI Jericho 941 CO2 Airsoft Pistol is about medium to hard but defiantly not the worst airgun I have tested. After you quickly shoot off a full CO2 cartridge you may need a bit of a break to rest your trigger finger but the actual shooting experience is just fine and it does not effect accuracy too much once you get used to the pull and break point of the trigger.
"Accuracy was pretty good for a double action shooter, I got around a 1.5 inch grouping from a 20 foot away free standing position, shooting just a hair to the left but a bit on the high side. It is a bit unfortunately that the Jericho 941 does not have sight elevation adjustments as it would make a very accurate airgun otherwise. I also put the Cybergun IWI Jericho 941 through my Chrony Chronograph and got very impressive FPS results, actually starting off and staying well above the claimed manufacturers FPS. My 8 shot average on a new CO2 was a very high 488 FPS, again well above Cybergun's claimed 443 FPS."
Build Quality: Very good, the KWC Model 941 CO2 Airsoft Pistol weighs in at about 2 pounds which is a very hefty weight for a medium sized pistol. The build quality and fit and finish is good all around with decent usage of metal in the slide, magazine, outer barrel and trigger. There are not a lot of moving parts so I would expect good durability since there is not a lot to go wrong with this Airsoft pistol.
Realism: The KWC IWI Jericho 941 Airsoft Pistol is very close to the look, weight, and feel of the real Israel Weapons Industries Jericho 941! Even though it doesn't have a working slide it definitely looks the part with its cut out ejection port, full size drop out metal magazine and recessed metal barrel. The KWC Model 941 does not have any licensed trade marks to speak of but on the positive side of things it also doesn't have the ugly warning instructions written on it either.
All metal full size drop out magazine holds CO2 and Airsoft BB's.
Very accurate IWI Jericho 941 replica in terns of looks, size and weight.
Should get good FPS based on the steel BB version results.
Can expect lots of shots per CO2 based on Steel BB version.
Expecting good accuracy based on the steel BB version results.
Very affordable price at well under $100.
Cons:
Non-blowback and the slide is non-functioning.
The hammer is only for show and does not cock back for single action shots.
Non adjustable rear sights.
Trigger action is bit on the heavy side and gets a bit tiring after lots of shooting.
Comments:
For a relatively inexpensive Airsoft gun you get good value for your money, most importantly a very accurate reproduction of the real IWI Jericho 941 firearm in terms of size, looks and weight. I am hoping to get similar shooting results shooting the KWC Airsoft Model 941 as I did with my BB shooting Cybergun IWI Jericho 941 I tested a few yeas back as it was one of my highest fps BB pistols tested. So make sure to check back shortly for my Field Test Shooting Video Review for this Jericho 941 Airsoft version from KWC.
My Vimeo Videos for the KWC IWI Jericho 941 Airsoft Pistol:
Ammunition Capacity: 15 round full size drop out metal magazine.
FPS: 417.
Trigger Pull: The trigger pull on the ASG MK II is double action only which will make it a bit on the heavy and longer side when compared to a real steel Ruger MK II, it is smooth however and does have a nice satisfying click that sounds like a firing pin being release. The unfortunate part is that the real steel version is a single action only trigger and one that is super short and light so the contrast between the Airsoft and 22LR version may make this gun not practical is an optional training tool if you win the 22LR version also.
Accuracy: This part of the review is yet to be determined as I have not done my Field Test or Shooting tests for this pistol. I will put a link in here when I have done my official Field Shooting Test. For now all I can go on is some feedback from others that have claimed very high fps and excellent accuracy, I am looking forward to finding out for myself! You can watch my Ruger MK I Gas version Field Test Shooting Review to get an idea on how the ASG Ruger MK II version might perform.
Build Quality: ASG as usually distributes quality guns, the fit and finish on the ASG Ruger MK II Dual Tone CO2 6mm Airsoft Pistol is very good and there is use of metal where it needs to be like with the internal mechanical parts, the trigger, the safety, the rear fully adjustable sight and the full size drop out metal magazine that holds the CO2 and the Airsoft BB's. Thee MK II version has a metal upper which adds additional weight over the MK 1's plastic upper.
Realism: The ASG MK II is based on real steel Ruger MK II with the fluted barrel in a two-tone finish and looks very close to a real Ruger MK II. There is no blowback operation or bolt operation so that means that only a double action trigger is possible, this is a bit unfortunate since the real Ruger Mark II has an absolutely smooth and light single action trigger. On the positive side you can field strip the ASG Ruger MK II Dual Tone CO2 6mm Airsoft Pistol just like the real version.
If you own a real Ruger 22LR it would be nice to have for some backyard or basement shooting.
Adjustable rear sight for windage.
Adjustable Hop-up for Elevation.
Full size all metal drop out magazine that holds the CO2 and Airsoft BB's.
Metal upper barrel, Metal trigger, metal safety and many metal internals.
Very satisfying trigger sound, sounds like a real firing pin :)
Field Strips just like the real steel Ruger MK Series.
Cons:
Plastic sights front and back, plastic trigger.
No blowback (Would have allowed for a true single action trigger)
Double Action Only, unlike the real steel version that is single action only.
Comments:
Compared to the my previous review of the ASG Ruger MK I, the MK II for me is a big improvement. The metal upper barrel assembly makes all the difference in terms of weight and feel and with the two-tone look it is for sure a very attractive looking pistol. I also prefer using CO2 for the increased performance of higher fps and less cool down effect over a gas system. I am hopping my Field test Shooting video goes well and the ASG Ruger MK II Dual Tone CO2 6mm Airsoft Pistol performs on point for me.
My Vimeo Table Top Video Review for this ASG Ruger MK II Airsoft Pistol:
Ammunition Capacity: 20 round metal stick magazine.
FPS: 400 fps claimed.
Trigger Pull: Trigger pull on the Umarex HK 45 Metal Slide CO2 BB Pistol is double action only but doesn't feel too bad, it has the traditional longer double action pull but I did not find it to be too heavy and the release point was fairly predictable for me allowing for some good overall accuracy.
Accuracy: I have already done a full Felid Test Shooting Review Video for the Umarex HK 45 Metal Slide CO2 BB Pistol so make sure to check that one out! In summary I got a bit higher fps then claimed at 420 fps with a 5 shot string using a brand new CO2 with RWS 5.1 grain zinc coated steel BB's. From 30 feet away shooting on a paper target using a semi rested posting I was able to place 10 BB's within 1.5 inches, almost close to a 1 inch grouping. The shot placement for me was just a tad to the left and a bit down but several shots hit the bulls eye so out of the box accuracy was really good on this low cost BB pistol.
Build Quality: The Umarex HK 45 Metal Slide CO2 BB Pistol is built fairly basic with few moving parts so there is not much to go wrong, the fit and finish is good and there is metal where it needs to be internally and also the trigger, magazine and slide.
Realism: The Umarex HK 45 Metal Slide CO2 BB Pistol is a very good overall HK 45 Replica BB pistol in terms of size and looks, it has full HK licensing and even has a metal slide and polymer frame like the original real steel HK 45. It is a bit lighter bit not by too much. There is no working slide and the slide catch/release and hammer are molded into the gun. The only working parts would be the safety, magazine release and trigger.
Metal where it matters, slide, magazine, trigger, internals.
Nice replica of the original HK 45.
Fully HK Licensed.
White dot sights easy to sight in your target on most backgrounds.
Decent double action trigger.
Picatinny rail for accessories.
Cons:
None blowback with a fixed slide.
Slide catch/release and hammer are moulded in and none functioning.
Sights are none adjustable.
Comments:
For a rather low cost CO2 4.5mm steel BB pistol, the Umarex HK 45 has a lot going for it! It is fully HK Licensed with a metal slide and metal parts where you want and need it. The accuracy and power are both good and even the double action trigger is very usable. Sure the Umarex HK 45 Metal Slide CO2 BB Pistol is a pretty basic gun with few moving parts but then again simple is sometimes better in terms of reliability. If you are an HK fan and want a low cost well made and good performing BB pistol then checkout the Umarex HK 45.
My Vimeo Table Top Review for the Umarex HK 45 Metal Slide CO2 BB Pistol:
Trigger Pull: Trigger pull on the Webley MK VI .455 CO2 Shell Loading BB Revolver is great in both single and double action, for a shell loading revolver the double action is the best I have come across with next to no friction like I would usually find with shell loading revolvers when shot in double action mode.
Accuracy: I tested the Webley MK VI .455 CO2 Shell Loading BB Revolver on my pool deck first off shooting 6 rounds through my Chronograph. The claimed fps is 427, I got really close to 400 fps in my testing so there is the potential for this revolver to shoot up into the low 400's. When I stepped back 30 feet and shot 6 rounds form my semi rested position, I got a really tight 1 inch group with almost all the rounds landing in the bulls eye. My shots where just a hair to the right but not by much which is good since the sights on this pistol are none adjustable. You can check-out my full Field Test Shooting Video here!
Build Quality: The Webley MK VI .455 CO2 Shell Loading BB Revolver is pretty much an all metal construction other than the plastic grips and any internal seals. The fit and finish is excellent with a great overall weight in the hand. The only complaint I have is that the grips being a thin plastic seem kind of low quality compared to the rest of this otherwise high quality Webley CO2 BB Revolver.
Realism: In terms of replicating a real steel Webley MK VI .455, Webley did a really great job with their CO2 BB firing version. Webley even includes a Small Arms Training Manual based off of the real steel variant. Webley based the BB CO2 MK VI from the original blueprints and the licensing is form the original 1915 version. The only real tell that this is a CO2 BB revolver would be the small safety switch on the lower right side frame and the CO2 valve located right behind the hammer.
Looks amazing and is a very accurate replica of the real steel Webley MK VI.
Great weight and feel in the hand at 2.4 pounds
nice deep Recessed barrel with true .455 caliber opening.
Break barrel design makes it really easy to load the dummy shells.
Hammer / trigger action is great in single and double action.
Webley Licensed.
Well concealed CO2.
Fairly discreet safety location.
No ugly warning instructions on the gun!
Cons:
One of the higher cost shell loading revolvers we sell.
Sights are none adjustable.
Real version would shoot .455 caliber rounds, the dummy shells are actually closer to 357.
Could be a bit loud for some back yard shooters?
Plastic grips seem a bit cheap compared to the rest of this high quality gun.
Comments:
Another classic shell loading CO2 BB Revolver, nothing wrong with that, I remember a time when finding a realistic revolver, even a modern version was hard to do. Now we have a growing selection of super realistic revolvers that replica their original real steel variation with ultra realism. The Webley MK VI .455 CO2 Shell Loading CO2 BB Revolver is no exception and makes for yet another option if you want a well designed, super functional and ultra realistic classic BB revolver.
My Vimeo Table Top Review for the Webley MK VI .455 CO2 Shell Loading CO2 BB Revolver :
In part one test of the Umarex Polymer Colt Python 357 CO2 BB Revolver, the Chronograph velocity test I managed to get 5 reading out of 10 shots (Chrony was acting up again) and averaged 426 fps using 5.1 grain zinc coated RWS BB's with a brand new 12 gram CO2. Perhaps my average would have been slightly higher if I got all 5 readings on the first 5 shots since the fps is always a bit higher. My highest reading was 442 fps while my lowest reading near the end was 406 fps.
Part two, the accuracy component to this Shooting Field Test gave my fairly good results but perhaps not as good as the all Metal Shell Loading Umarex Colt Python I tested out earlier. I did find the Umarex Polymer Colt Python 357 CO2 BB Revolver shot well centered but got about a 2 inch grouping shooting 10 rounds on the paper target. If you find yours is not set to shoot exactly on the bulls eye you can easily adjust the sights for windage and elevation.
If you are wanting a higher than 6 round CO2 BB Revolver with a low price tag, good velocity, easy loading, adjustable sights, a smooth single and double action trigger and decent accuracy than checkout the Umarex Polymer Colt Python 357 CO2 BB Revolver!
