Make sure to watch my Table Top Review Video if you want more info on the details and specifications for the Daisy Powerline 5170 CO2 BB Pistol! in this Field Test Shooting video I test out the Daisy Powerline 5170 CO2 BB Pistol inside the Replica Airguns indoor Sea Can Airgun Range to see how well it performs in terms of Velocity and Accuracy. The temperature was 20 degrees Celsius (68 degrees Fahrenheit) so not too hot or too cold on this test day. I was also using a brand new CO2 along with 5.1 grain RWS zinc coated steel BB’s.
For the first test to find out what the actual velocity is for the Daisy Powerline 5170 CO2 BB Pistol, I placed 5 rounds through my Chronograph back to back and I was able to get an average of 456 fps with the fastest shoot hitting 460 fps and the slowest shot in the string hitting 451 fps. All within 9 fps of each other so very consistent.
Next I setup a fresh paper target 30 feet down range and proceeded to do my best to obtain a 10 shot grouping using a seated and rested shooting position. Most of the shots form the Daisy Powerline 5170 CO2 BB Pistol where all under 1.5 inches apart, just a little bit high and slightly to the left. I did get a flyer that went a little bit lower than the rest lengthening out the 10 shot grouping to about 2 inches in diameter. I am pretty sure I would be able to get a 1 inch grouping with the Daisy Powerline 5170 CO2 BB Pistol after some practice.
Overall the Daisy Powerline 5170 CO2 BB Pistol performed well for me shooting consistently without any issues. The Daisy Powerline 5170 CO2 BB Pistol is fairly basic in design but does have the added much suppressor that allows for a longer inner barrel giving it a little more fps. You also have the removable sight rail fi you want to add some optical sights or perhaps a laser or tactical light or maybe all of them? Pickup the Daisy Powerline 5170 CO2 BB Pistol in a variety of colors over at the Replica Airguns Online Canada and US Stores!
Make sure to watch my Table Top Review Video if you want more info on the details and specifications for the Crosman P10 Wildcat CO2 BB Pistol Airgun Kit! in this Field Test Shooting video I test out the Crosman P10 Wildcat CO2 BB Pistol Airgun Kit inside the Replica Airguns indoor Sea Can Airgun Range to see how well it performs in terms of Velocity and accuracy. The temperature was 20 degrees Celsius (68 degrees Fahrenheit) so not too hot or too cold on this test day. I was also using a brand new CO2 along with 5.1 grain RWS zinc coated steel BB’s.
For the first test to find out what the actual velocity is for the Crosman P10 Wildcat CO2 BB Pistol Airgun Kit I placed 5 rounds through my Chronograph back to back and I was able to get an average of 396 fps with the fastest shoot hitting 404 fps and the slowest shot in the string hitting 389 fps. Interestingly enough the fastest shot was the last shot in my 5 shot string so CO2 cooling did not effect the Crosman P10 Wildcat CO2 BB Pistol Airgun Kit too much.
Next I setup a fresh paper target 30 feet down range and proceeded to do my best to obtain a 10 shot grouping using a seated and rested shooting position. I may have only loaded 9 rounds this time but I was still able to get a good idea on how well the Crosman P10 Wildcat CO2 BB Pistol Airgun Kit performs in the accuracy department. Most of the shots where all under 2 inches and well center on the target with at least 3 or 4 rounds in the bullseye. I did get a flyer that went rather high but we will assume there may have been a bad BB in the bunch shine I did not feel I pulled that shot at all and since the other rods all placed well together well will go with the smaller grouping of under 2 inches.
Overall the Crosman P10 Wildcat CO2 BB Pistol Airgun Kit performed well for me shooting consistently without any issues. The Crosman P10 Wildcat CO2 BB Pistol Airgun Kit is a very basic airgun with your standard double action trigger that will be on the longer side, that said it felt pretty good and was not overly heavy with a fairly predictable pull and release making it easy enough to find your target. Action shooting will be OK too since the trigger is not super heavy for a double action only trigger. Pickup the Crosman P10 Wildcat CO2 BB Pistol in a variety of colors over at the Replica Airguns Online Canada and US Stores!
We had a lot of great new Airguns that I reviewed this year at Replica Airguns. Some of them really stood out to me and so I made a video showing my Favorite Replica Airgun Picks of 2019. Of course there where many other Airguns that could has just as easily made this video but I had to draw the line somewhere and pick the ones that in my opinion where the best of 2019. Make sure to watch my Vimeo video where I go into some more details on why I liked each Airgun.
Below is a list of the top Replica Airgun Picks of 2019:
It’s been a while since I had Blank Gun available for silent auction here in Canada and this one is an EKOL Firat Compact 9mm PAK Front Firing Blank Gun in great shape well kept and with only 20 rounds through it.
It comes with a hard shell case, the flare adaptor, take down tool and manual. Pretty much everything it came with. The finish is closest to a stainless but I believe was called Chrome back in the day. I would call it a Satin nickel finish? Anyway watch the video and look at the photos to get a better idea of what I mean.
The EKOL FIrat is a lot like the EKOL Jackal which also came in compact and Magnum version and resemble a Beretta 92. The EKOL Jackal however is semi auto and full auto capable while the EKOL Firat is semi auto only. This will save you a lot of money on blanks since blanks cost around $40 for a 50 pack.
To take part in the silent auction for this EKOL Firat Compact 9mm PAK Front Firing Blank Gun you will need to email me and let me know what your top bid is for it. The person with the highest bid will become the new only once paid for.
There are a couple things to keep in mind:
Get your bids in by noon Monday December 23rd.
Shipping will be added to the cost which is $29
Payment must be made within 24 hours of notification via EMT (Email Money Transfer), details to follow.
This can be a Christmas gift to yourself but it is not likely you will receive it by Christmas.
Type: GBB AIrsoft Pistol. Manufacturer: Made by Tokyo Marui. Model:Hi-Capa 5.1 D.O.R. Materials: Mostly polymer with metal components. Weight: 1.85 pounds (839 grams). Barrel: 4.4 inches (112mm) metal non-rifled. Propulsion: Green gas. Action: Semi auto blowback, single action only trigger. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 31 round drop out full size metal magazine. FPS: Claimed 365.
Trigger Pull: The single action only trigger pull on the Tokyo Marui Hi-Capa 5.1 D.O.R GBB Airsoft Pistol is extremely nice, there is virtually zero take-up with a light and easy release. You can really hammer out quick shots with this Airsoft pistol. Other than the Tokyo Marui Strike Warrior .45 1911, one of the best 1911 triggers I have tested so far.
Build Quality: TheTokyo Marui Hi-Capa 5.1 D.O.R GBB Airsoft Pistol on the outside it is mostly all plastic (Slide and portion of the frame). That said the quality is fantastic, fit and finish is top notch everywhere and you will find metal parts where they need to be as in the inner and outer barrel, trigger, hammer, slide catch release, back strap safety, trigger group, magazine and many more internal parts.
Realism: The Tokyo Marui Hi-Capa 5.1 D.O.R GBB Airsoft Pistol is built on the Colt 45 1911 design but is obviously a more modernized and tacticle version of the classic 1911. The only factor that separates the Tokyo Marui Hi-Capa 5.1 D.O.R GBB Airsoft Pistol from that of a traditional 1911 in design is the lack of a barrel bushing which kind of makes field stripping and access to the Airsoft guns intervals a little bit easier. You still get that 1911 feel and awesome Single Action Only Trigger with your thumb safety and slide catch release in all the familiar places. Of course the Grip safety works as you would expect on a 1911.
Pros:
Light and crips flat faced SAO trigger feels great.
Fit and finish is excellent, next to zero slide wiggle.
Very cool looking tactical modernized 1911.
Direct Optic Ready removable rear sight to accommodate for included red dot mounting plates.
Optional under-rail plate included.
Full size high capacity 31 round double stack metal magazine.
Ambidextrous thumb safeties.
Working grip safety as you would expect on a 1911 based gun.
Most mechanical parts work just like a real steel 1911 and can be easily field stripped to access the hop-up.
Super fast blowback action, great for quick action shooting.
Decent 1.85 pounds weight considering much of the Airsoft gun is plastic.
Cons:
Mostly all plastic build.
Does not have the barrel bushing found on traditional 1911’s.
No white dots on rear sight.
Comments:
So far I have reviewed three of the Tokyo Marui Airsoft pistols and all three have impressed me. Even with a mostly plastic build at least externally in the slide and frames, these Airsoft Pistols still feel and shoot great even if they are a little on the light side. That may be a plus for some people who want a nice light weight side arm that is not weighing them down on the field. The plastic slides really cycle fast and are super snappy, when combined with short and light tirggers you can pop off rounds amazingly fast and on target. For the price I really think any of the Tokyo Marui Airsoft Guns would be a great choice. I do however have a soft spot for 1911’s and so for me the Tokyo Marui Hi-Capa 5.1 D.O.R GBB Airsoft Pistol would be my choice out of the three I have reviewed so far.
Type: Non-blowback CO2 BB Pistol. Manufacturer: Distributed by Crosman. Model:P10 Wildcat / Phantom. Materials: Plastic & metal. Weight: 1.1 pounds (500 grams). Barrel: Smooth bore barrel. Propulsion: CO2 x 1. Action: Semi auto non-blowback, double action only trigger. Ammunition Type: 4.5mm steel BB's. Ammunition Capacity: 20 round drop out plastic magazine. FPS: Claimed 480.
Trigger Pull: The trigger pull on the Crosman P10 Wildcat CO2 BB Pistol is typical of a Double Action Only Trigger and so you will expect it to be a longer medium to heavy pull. I’d say it’s more of a medium pull, it’s not going to be the fastest action shooter because of this but it will get the job done emptying the 20 round stick magazine quick enough. Like many of these lower cost basic CO2 BB pistols the barrel acts like the hammer in that it does protrude out of the barrel opening when you pull the trigger and snap back upon release.
Accuracy & Power: At this point I have not shot the Crosman P10 Wildcat CO2 BB Pistol so I can only quote what Crosman claims on their packaging in terms of velocity which is a peppy 480fps. We will have to see if this figure is close to the mark when I get to the Field Test Shooting Review for the Crosman P10 Wildcat CO2 BB Pistol, along with test results for accuracy at 30 feet downrange.
Build Quality: The Crosman P10 Wildcat CO2 BB Pistol is mostly all plastic with some metal internal parts where they need to be for strength and durability issues. The Crosman P10 Wildcat CO2 BB Pistol is basically two plastic halves put together with screws on the right side. This may not be the prettiest way to build a CO2 Airgun but it does work and keeps things simple, simple means there are a lot less things to go wrong which means you will have an airgun that is reliable for a long time.
Realism: The Crosman P10 Wildcat CO2 BB Pistol is not a replica of any specific real steel pistol in production but in my opinion it kind of looks like a hybrid of a Beretta and Sig merged together. Obviously the Blue and Pink versions are made to show they are not real steel guns but you can get the P10 in the all black Phantom version which will look more like a real gun. There are few moving parts on the Crosman P10 line of Airguns, just the trigger, safety and magazine release. All other parts are moulded into the plastic with no working slide or even hammer. The CO2 tab is well hidden by the grips but the barrel is not reassessed at all.
Blue and pink color scheme may ease some parents when buying a first BB gun.
High FPS rating.
Non-blowback will get more shots per CO2.
Comes with a generic nylon holster you can use with other airguns too .
CO2 tab is nicely hidden inside the grip.
Double action trigger pull is long but not too firm.
Should work with other similar styled magazines commonly found on lower cost BB pistols.
Assembled in the US.
Cons:
All plastic gun for the most part with just a few internal metal parts.
Not many working parts pretty much all moulded gun.
Grips fairly loose, don't really snap into place, could fall off easily.
Comments:
I’m not really a big fan of all plastic non-blowback airguns as I have made aware in many of my other videos. That said there is a place for Airguns like the Crosman P10 Wildcat CO2 BB Pistol for those looking to buy an Airgun not so much as a close replace but simply just to shoot at targets and have fun with. The Crosman P10 Wildcat CO2 BB Pistol will do just that very dependably while offering lots of shots per CO2 with a high fps, it should also get reasonable accuracy while doing so. Being able to get it in a variety of colors means you can personalize the Crosman P10 Wildcat CO2 BB Pistol a bit more and the blue and pink versions may be the deciding factor for some parents sitting not the fence on whether or not to allow their young adult or teenager to buy their first CO2 BB Pistol.
Type: Non-blowback CO2 BB Pistol. Manufacturer: Distributed by Daisy. Model:Powerline 5170. Materials: Metal & plastic. Weight: 1.8 pounds. Barrel: Smooth bore goes entire length of much compensator. Propulsion: CO2 x 1. Action: Semi auto non-blowback, double action only trigger. Ammunition Type: 4.5mm steel BB's. Ammunition Capacity: 21 round drop out plastic magazine. FPS: Claimed 520.
Trigger Pull: The trigger pull on the Daisy Powerline 5170 CO2 BB Pistol is that of a Double Action only Trigger and so you will expect it to be on the long side. That said it is smooth all the way through the pull and no overly heavy. It also has a rather satisfying feeling that I can only explain as a feeling that you are working well put together internal metal parts.
Accuracy & Power: At this point I have not shot the Daisy Powerline 5170 CO2 BB Pistol so I can only quote what Daisy is saying in terms of velocity which is rather optimistic 520fps. This sounds high but we will have to see when I get to the Field Test Shooting Review for the Daisy Powerline 5170 CO2 BB Pistol.
Build Quality: The Daisy Powerline 5170 CO2 BB Pistol seems to be decently made for a mostly plastic airgun. Like I said the metal trigger feels solid and it also has a metal safety which is nice, other than that all other external parts are plastic but it does feel like there are a lot of metal internal parts based on the weight. I would have liked to see more metal in the magazine as it does feel to be the cheapest part of the Daisy Powerline 5170 CO2 BB Pistol.
Realism: The Daisy Powerline 5170 CO2 BB Pistol is basically a replica of a 1911 in most ways. It does have a shorter slide than a standard 1911 but the compensator adds a lot of length back to the Daisy Powerline 5170 CO2 BB Pistol. The working safety is out of place for a 1911 since it is located where the slide catch would be and does not even look like a 1911 slide catch. The location where the real 1911 safety would be has a moulded in non-working safety. Not to be overly picky but the trigger on a 1911 is also totally different since it would be a very short single action only trigger. The only working parts on the Daisy Powerline 5170 CO2 BB Pistol are the trigger, safety and magazine release.
Fairly low cost with what looks to be decent fps and hopefully good accuracy.
Has an added compensator that extends the barrel internally.
Double action trigger is very smooth and satisfying feel to it.
Comes with sight rail for addition of top, bottom and side Weaver accessories.
Safety actually looks like part of the gun even though not a 1911 style lever.
CO2 tab is well hidden by magazine but plate.
Weight and feel of gun are pretty good considering so much plastic.
Pretty decent replica of a Colt 1911.
Made in Japan.
Cons:
Will need an optical sight of some sort or will have to take off sight rail to use built in sights.
Drop out magazine is all plastic.
Not many working parts.
Comments:
I’m not really a big fan of all plastic non-blowback airguns but I am willing to give the Daisy Powerline 5170 CO2 BB Pistol a chance since it does have some things going for it like high fps which I know is important to many of you. The Daisy Powerline 5170 CO2 BB Pistol also has a really nice double action trigger which should make shooting it easy and fun. The sight rail also gives the Daisy Powerline 5170 CO2 BB Pistol a lot of versatility when it comes to making the Daisy Powerline 5170 your own by adding on pretty much any accessory you can imagine.
In a way I have already Field Tested the Air Venturi TR5 .177 Caliber Pellet Rifle, well at least in the Baikal version. The Air Venturi version is pretty much a knock of of the Baikal IZH MP-61 which not only look a lot alike but also performed very similarly for me, checkout my Baikal YouTube Video Review for comparison. All that said we can not get Baikal products here in North America anymore so it’s great that Air Venturi has recreated a very similar product for us to have in Canada and the US.
Moving on to the Field Test Review for the Air Venturi TR5 .177 Caliber Pellet Rifle, I first placed 5 shots through my Chronograph to see if the Air Venturi TR5 .177 Caliber Pellet Rifle did in fact shoot around 500 fps and in fact I was able to get all 5 shots up and over 500 fps averaging around 513 fps. Still within our Non-regulated firearm laws here in Canada since we where still under the 4.2 foot pound energy limit using 6.9 grain pellets.
As mentioned before when I shot the Baikal IZH MP-61 I was able to get very similar results but I did have an optical scope on the Baikal IZH MP-61 as compared to the Air Venturi TR5 .177 Caliber Pellet Rifle where I just used the open sights. In my opinion the Air Venturi TR5 .177 Caliber Pellet Rifle is good value for your money offering a unique design with excellent performance and getting as much power out of a pellet rifle as you can get here in Canada without requiring a firearms license.
Pick one up in our Canada or US Online Replica Airguns stores!
It’s always fun shooting a Paintball Gun like the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol for a change but in this case it’s not all that different then shooting one of my BB or Airsoft pistols, with the acceptation of the .43 caliber rubber balls. I went with rubber balls rather than Paintballs inside my Sea Can Indoor Airguns Shooting Range to keep things clean. Actual Paintballs may have performed a little different than the rubber balls but this gives us a good idea on what the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol is capable of
First, I put five rounds through my Chrony Chronograph to see what the real world FPS would be, keep in mind I was using rubber balls rather than paintballs and the rubber balls are a little bit heavier than paintballs so this could bring the FPS down a bit compared to the slightly lighter paintballs. Using a brand new CO2, the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol average 315 FPS which was higher than the claimed 290 FPS! Temperature inside my Sea Can Airgun Shooting Range was around 24 degrees Celsius or 75 degrees Fahrenheit.
Moving on to my accuracy testing, as per usual I positioned myself 30 feet back from my fresh paper target and using a seated and rested shooting position I shot a full magazine (8 rounds) of rubber balls on target with the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol. I was not expecting as tight groups as I would get using a BB or Airsoft pistol since Paintball guns are not known for super tight groups. I did manage to shoot around a 6 inch group with most of the shots staying within around 3 inches all pretty well centered. This is about what I was expecting as paintball guns are not meant for "target practicing", generally you are going to be shooting human sized objects and hoping to get some well placed center mass shots. 3-6 inch accuracy at 30 feet will get the job done for sure. I did find the trigger using rubber balls did have a bit more friction while the inner barrel seated itself into the magazine. When shooting quickly with the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol it is much less noticeable and overal the trigger is not bad.
I know some of you are going to ask about using the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol with rubber balls for non-lethal self defense and the reality is it will not stop a person who is determined on hurting you. There is simply not enough stoping power here. Will it a lot if you get shot up close with one of these Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistols especially directly on the skin ? For sure but a well timed punch has more chance of dropping someone than a .43 caliber rubber ball moving at around 300 FPS. You may scare someone off simply by brandishing it but you take the chance of the person calling your bluff. Perhaps 8 rubber balls to the face will change their mind but that's a chance you have to figure out if you want to take or not.
Type: Paintball Gun. Manufacturer:Umarex - T4E. Model:S&W M&P9 M2.0 Materials: Metal & Polymer. Weight: 763 grams (1.7 pounds). Barrel: Smooth bore. Power Source: 1x12 gram CO2. Action: Semi-Automatic with blowback action. Ammo Type: .43 Caliber Paintball or Rubber Ball. Ammo Capacity: 8 Rounds. FPS: 290.
Trigger Pull: The trigger pull on Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol feels a lot like a double action trigger mainly because when you pull the trigger the inner barrel travels backwards into the magazine which seals off the barrel form the magazine so less CO2 is wasted going it not the magazine and also placing a paintball round in the barrel. This does make the trigger a little bit longer and heavier than a single action trigger. I believe the internal hammer/striker is engaged from the blowback action.
Build Quality: The build quality of the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol is really very good, metal parts are where you would expect them, the slide, slide catch, barrel, magazine and most internal parts giving the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol a nice near 2 pounds (1.7 pounds) of weight with the magazine in which makes the Paintball version a little heavier than the real steal version (1.54 pounds) but once the real steal version is loaded with a full mag this may even out a bit. The Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol does have a polymer frame but again this is normal with todays modern guns and helps keep the weight down. Fit and finish is also very good!
Realism: The Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol is a near perfect replica of the real steel S&W M&P9 M2.0 Pistol, from the fully licensed markings to the large .43 caliber diameter barrel. If you placed the Paintball version side by side with the real steel version I doubt you could tell them apart unless you start inspecting it really close up and working the action. You will find that the slide cycle distance is a bit shorter than it would be meaning that when the side catch is engaged the slide does not go as far back as it the real 9mm S&W M&P9 M2.0. Field stripping the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol will requires some tools and pin removal.
Another Field Test Shooting Video Review coming for the Replica Airguns Sea Can Indoor Airgun Shooting Range! In todays Shooting Review I test out the Schofield No. 3 CO2 BB-Pellet Revolver using both 4.5mm 5/1 grain Steel BB’s and .177 Caliber 6.9 grain Lead Pellets to see how well they perform in velocity and accuracy. As always I use a brand new CO2 for my velocity testing and for reference the temperature during my testing in the Sea Can was 23 degrees Celsius or 73 degrees Fahrenheit. For my accuracy portion of the shooting test I use a rested and seated shooting position shot 30 feet away from my fresh paper targets.
Starting off with the velocity or power potion of my Field Test Shooting Video for the Schofield No. 3 CO2 BB-Pellet Revolver. I first used the 4.5mm Steel BB shells and shot 3 rounds through my Chronograph averaging 369 fps. I then loaded up the Schofield No. 3 CO2 BB-Pellet Revolver with pellet shells and again placed three .177 caliber lead pellets through my Chrony and got a very similar result with an average of 361 fps. Keep in mind the lead pellets where 6.9 grain versus the steel BB’s at only 5.1 grain, so the lead pellets will be carrying more raw energy at the point of impact even though they where going just a tad bit slower than the steel BB’s.
In terms of accuracy both rounds performed about the same shooting at my paper target 30 feet away. Since the Schofield No. 3 CO2 BB-Pellet Revolver has a 6 round cylinder I shot 6 sounds for each test, 6 steel BB’s and then 6 lead pellets. I also changed the targets for each type of ammo between reloading. I found the Schofield No. 3 CO2 BB-Pellet Revolver shot fairly close to the bullseye, l but with both the Steel BB’s and lead pellets I got one outlier that spread out my groupings significantly, the other 5 rounds where all close being about 2 inches apart? Perhaps it was a bad or misshaped round, or maybe even me ;) I did notice the lead pellets seemed to have a really nice 4 round group out of the 6 that all fell within the bullseye. Hard to really say if BB’s or pellets performed better than the other one at least in my testing.
Overall the Schofield No. 3 CO2 BB-Pellet Revolver shot well for me, the trigger is nice and short and light making placing your shots easy, of course since it is a single action only trigger you kind of need to reset yourself between every shot which can effect groupings just a bit. Since the barrel is not rifled with no danger of damaging the rifling, you can really shoot what ever ammo type you feel like shooting or have on hand and since Schofield No. 3 CO2 BB-Pellet Revolvers get about the same speed and accuracy then it really doesn’t matter that much at the end of the day!
In this Replica Airguns Video I talk about our already in progress Black Friday Sale and also who the winners are for this Years Replica Airguns Halloween Contest Giveaway.
Starting with the Replica Airguns Black Friday Sale you can already save up to 30% on select items in our Canada Replica Airguns Online Store. This is kind a pre-sale so if you see something you like grape it now since we may be changing the sale items up as we get closer to and for Black Friday.
Now onto our 2019 Replica Airguns Halloween Contest Giveaway winners, you guys decided which videos you liked best so here are the winners in order of most lies, I have also included views for your reference.
I hate to drag this on a bit longer but I really am having a hard time deciding on the top three videos for this years Replica Airguns Halloween Contest. This year more than any other it has been more about quality over quantity meaning we didn't get a lot of Halloween Contest video submissions but the ones we did get are really well done with lots of time, effort and thought put into each video.
So rather than myself choosing the winners, I will put it in the hands of you my dedicated followers and viewers. Read the instructions below on how to take part in deciding who will be the winners of this years Replica Airguns Halloween Contest!
The following product review for the Comica WS60 UHF Dual Mini Wireless Microphone Combo has nothing to do with Replica Airguns but as a YouTuber with a couple of YouTube channels, I have to make sure I not only have good quality video but also good quality audio when I make a YouTube Video for one of my channels.
After all if it sounds like I’m in a wind tunnel or the bat cave and you can not hear clearly what I’m saying then it can be very distracting for you the viewer to understand what I ‘m trying to share with you!
Perhaps you can also utilize a product like the Comica WS60 UHF Dual Mini Wireless Microphone Combo for your audio and video needs, which could also be for something social media related or even just for your own personal use to get the best quality home video and audio.
For the last couple of years I have been using a lapel mic more and more in my videos and I try to use one whenever possible since the audio is just so much better than the Microphone audio built into the camera. It's not that the camera mics are really all that bad, the problem is that most of the time the camera is simply not close enough to the person speaking so you tend to get a lot of background and room noise which makes the speaking audio sound distant with noticeable ambient noise and echo.
Generally I have been using a wired lapel mic that I record directly into my SmartPhone, which I place in my pocket while recording. I use a different camera to record my vide, I then sync the audio to the video in post production on my computer but this requires a bit of audio and video software know how. The advantage to a wireless setup is that you can record directly into the camera if it supports an audio input meaning no more requirements to sycn audio later and no long cord bwteen the audio source and the camera. A wireless setup usually is more compact and versatile. What I like about the Comica WS60 UHF Dual Mini Wireless Microphone Combo is the fact that it comes with two lapel mics that both have their own transmitter so they can be worn independently by two separate people, perfect for conducting interviews or even when you simply need a mic in more than one location.
In this Comica WS60 UHF Dual Mini Wireless Microphone Combo YouTube Video Review I first unbox the Comica WS60 UHF Dual Mini Wireless Microphone Combo and show you what you get inside the box and talk about some of the basic features and specification. I then test it out and record audio so you can hear for yourself what it sounds like. I first test it plugged into my SmartPhone like I normally do and then I pug it into my DJI Osmo Pocket for a second reference test. Please keep in mind I performed my original testing without monitoring the real time audio output so I did not catch that there was some interference from my overhead LED lighting. I was able to change the channels on my Comica WS60 UHF Dual Mini Wireless Microphone Combo and completely remove the background bussing I was getting from the LED lighting in my room.
Here are some basic Details and Specifications for the Comica WS60 UHF Dual Mini Wireless Microphone Combo.
System:
Wireless Transmission: Digital UHF
Number of RF Channels: 24
Included Transmitters: 2 x Body pack with Microphone
Diversity: Non-Diversity
RF Frequency Band: A: 568.125 to 579.125 MHz - B: 580.125 to 591.125 MHz
RF Bandwidth: 11 MHz
Max Operating Range: 196.9' / 60 m (Line of Sight) - 98.4' / 30 m (with Obstruction)
Latency: <40 ms
Encryption: None
Modulation: FM
Receiver:
Form Factor: Camera-Mount / Portable
Mounting Options: Shoe-Mount, Tabletop (with Included Hardware)
Antenna: 1 x Internal, Fixed
Number of Audio Channels: 2
Audio I/O: 1 x 1/8" / 3.5 mm TRS Female Unbalanced Line Output - 1 x 1/8" / 3.5 mm TRS Female Unbalanced Headphone Output
Frequency Response: 20 Hz to 18 kHz
Network I/O: None
Word Clock I/O:None
USB/Lightning Connectivity: 1 x USB Type-C (Bus Power, Charging)
Approximate RF Sensitivity: -83 dBm
Power Requirements Battery or Bus Power (USB)
Battery Type: 3 x AAA (Not Included)
Approx. Battery Life: 4 Hours
AC/DC Power Adapter: 5 VDC (Not Included)
Display & Indicators: 1 x Back-Lit LCD (Battery Status, Channel, Data Transmission, Group, Level, RF Level) - 2 x LED (Data Transmission)
Operating Temperature: 32 to 122°F / 0 to 50°C
Storage Temperature: -4 to 140°F / -20 to 60°C
Dimensions: 4.1 x 2.6 x 0.7" / 104 x 65.2 x 18 mm
Transmitter:
Form Factor: Body pack with Microphone
RF Output Power: 10 mW
Audio I/O: 1 x 1/8" / 3.5 mm TRS Female Unbalanced Input
Pad: None
Muting: Off/On Switch
Signal Processing: High-Pass Filter:
Sync Method: Manual
Antenna: 1 x Internal, Fixed
Power Requirements: Battery or Bus Power (USB)
Battery Type: 3 x AAA (Not Included)
Approx. Battery Life: 4 Hours
USB/Lightning Connectivity: 1 x USB Type-C (Bus Power, Charging)
Display & Indicators: 1 x Back-Lit LCD (Audio Level, Battery Status, Channel, Group, High-Pass Filter, Mute, RF Output Power) - 1 x LED (RF Output Power)
Operating Temperature: 32 to 122°F / 0 to 50°C
Storage Temperature: -4 to 140°F / -20 to 60°C
Dimensions: 4.1 x 2.6 x 0.7" / 104 x 65.2 x 18 mm
Microphone:
Form Factor: Lavalier
Color: Black
Sound Field: Mono
Output Connectors: 1 x 1/8" / 3.5 mm TRS Male Unbalanced
Packaging Info:
Package Weight 2.055 lb
Box Dimensions (LxWxH) 9.7 x 7.3 x 4"
Make sure to watch my full YouTube Video Review for the Comica WS60 UHF Dual Mini Wireless Microphone Combo:
Type: BB/Pellet air revolver. Manufacturer/Distributor: Bear River. Model: Schofield No. 3 Materials: Mostly metal with plastic grips. Weight: 2.4 pounds. (1089 grams) Barrel: 7 inch (178mm) smooth bore barrel. Propulsion: 12 gram CO2. Action: Revolver, single action only. Ammunition Type: 4.5mm steel BB's and .177 Cal. Pellets. Ammunition Capacity: 6 rounds. FPS: 445fps.
Trigger Pull: The trigger pull on the single action only Schofield No. 3 CO2 BB-Pellet Revolver is what you would expect from a pistol of this design. Like the Colt Single Action Army the trigger pull is very short, light and crips, perfect for taking your time and getting a precise shot on target. You will of course have to cock the hammer manually before each shot ao no real action shooting.
Accuracy: I have not tested the Schofield No. 3 CO2 BB-Pellet Revolver in the Replica Airguns Sea Can Indoor Airgun Range but plan to get to it shortly. I will test out both 4.5mm Steel BB’s and some .177 caliber lead Pellets and see how the different ammo types effect both power and accuracy. Keep in mind the Schofield No. 3 CO2 BB-Pellet Revolver has a smooth bore barrel but I am pretty sure pellets will still perform well at 30 feet away.
Build Quality: The Schofield No. 3 CO2 BB-Pellet Revolver is built a lot like the Webley MK VI .455 CO2 Shell Loading Revolver line, perhaps even made in the same factory in Taiwan? The Schofield No. 3 CO2 BB-Pellet Revolver is pretty much an all metal construction other than the plastic grips and any internal seals. The fit and finish is excellent with a great overall weight in the hand. The pistol grips is a lot like what you have with the Colt Single Action Army pistol but the Schofield No. 3 CO2 BB-Pellet Revolver is a lot more front end heavy because of its beefy barrel.
Realism: In terms of replicating a real steel Schofield No. 3 CO2 BB-Pellet Revolver for sure looks and feels that part. The reassessed barrel and well hidden CO2 screw don’t give anything away that the Airgun version is not the real deal. But as with all of these shell loading Airgun Revolvers, the shells are actually closer to a .380 Caliber in diameter rather than a 45 which is what the real steel Schofield No. 3 CO2 BB-Pellet Revolver would be designed for.
If you are like a bulky revolver with good weight to it then the Bear River Schofield No. 3 is it.
Can shoot Steel BB’s or Pellets since it comers with both shell types.
Recessed barrel.
Well concealed CO2.
Shell loading design that loads from the back so no need to remove shells if you wish not to.
Single Action Only hammer and trigger action feel good, nice and light with short take-up and release.
Fairly discreet safety location right behind the hammer so easy to get at.
Super easy to load, pellet shells can even be reloaded with shells in the gun if you are using the pellet shells.
Really like the Nickel Finish on this gun.
Can get simulated Ivory grips for it if you prefer that look.
Cons:
Sights are not adjustable.
Warning instructions on side of the frame.
Barrel is not rifled for pellet use?
Only a Single Action Only Hammer and Trigger but true to the style of the gun.
Comments:
Yet another classic shell loading CO2 BB Revolver, and again the more the merrier in my option! I like that you get 12 shells with our kit version, 6 removable shells for 4.5mm Steel BB’s and 6 removable shells for .177 caliber Pellets. The Schofield No. 3 CO2 BB-Pellet Revolver is for sure a hefty revolver but the pistol grip is not super large so even people with smaller hands should not have a problem shooting the Schofield No. 3 CO2 BB-Pellet Revolver. The real problem is deciding which Shell Loading Airgun Revolver to buy now since we have so many to choose from… Classic or modern, nickel or black, or perhaps weathered?
My Table Top Review for the Schofield No. 3 CO2 BB/Pellet Revolver:
Here we have three very different products I Unbox and Preview for everyone. A Spring Piston multi-shot .177 Caliber Pellet Rifle, a single action BB/Pellet revolver that’s not a Colt! And a really nice looking Semi Auto Blank Pistol in a Chrome finish.
Let’s start with the Air Venturi TR5 Spring Piston 5-shot .177 Caliber Pellet Rifle. I think this is a really well thought out Air Rifle. It’s “almost a Bullpup” in design but it does actually load in front of the trigger just a bit, that said most of the spring piston is behind the trigger setup making it really compact yet with a longer than normal barrel compared to regular Break Barrel Spring Piston Air Rifles. The Air Venturi TR5 Spring Piston 5-shot .177 Caliber Pellet Rifle also has a side lever cocking mechanism along with a 5 round auto indexing magazine which makes it much quicker to cock and reload for fast follow-up shots, again compared to a standard Break Barrel Air Rifle, not to mention no barrel droop! The Air Venturi TR5 Spring Piston 5-shot .177 Caliber Pellet Rifle has a claimed fps of up to 500 so we are getting the max amount of velocity possible for our Canadian laws without making it a regulated firearm and requiring a PAL license. And by the way the Air Venturi TR5 Spring Piston 5-shot .177 Caliber Pellet Rifle does come in both a Lime Green and all Black version just in case you are not a fan of the Lime Green finish I show in this video.
Moving onto the Schofield No. 3 BB/Pellet 6 Shot Revolver Replica, if you like single action revolvers then take a look at the Schofield No. 3 BB/Pellet 6 Shot Revolver Replica. It’s a lot more bulky than a Colt Single Action Revolver and also has that top Break design that makes reloading quick and easy. The version we are selling inner Replica Airgun Online Store is the kit version that comes with 6 BB shells and 6 pellet shells so you can take your pick on ammo types. The barrel is not rifled so Steel BB’s will not hurt the Airgun and since pellets are skirted they do not need a rifled barrel to fly straight and true. You can expect around 445 fps for the Schofield No. 3 BB/Pellet 6 Shot Revolver Replica.
I don’t do a lot of paintball gun reviews, they just don’t come across my table all that often so it’s a lot fo fun when I do get the chance to shoot some beefier caliber ammunition in the Replica Airguns Sea Can Indoor Airgun Shooting Range. Of course I use rubber ball ammo rather than standard paintball rounds in order to keep the mess to a minimum.
I have not done my Table Top YouTube Video Review yet for the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun but you can checkout a Preview Video for now. In Summary the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun is a pretty much exactly what the name says. It’s basically a sawn off pistol grip styled double barrel shotgun that uses CO2 and shoots .68 caliber paintballs. You have a selector for shooting either out of the left or right barrel or if you want to can even both at the same time but this really slows down the fps so I would not advise it with the 200 fps version that I was testing with.
Now on to the actual testing of the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun! As alway I like to find out how close to the factory claimed fps I will get. Umarex claims around 200 fps for this version which is around 7.5 Joules of energy, apparently there is a 16 Joules version that shoots closer to 300 fps but we do not carry it at least right now. I put a couple fo rounds through my Umarex T4E HDS Double Barrel CO2 Paintball Shotgun using rubber ball paintballs which will be a little bit heavier than a standard paintballs and my first shot yielded 180 fps, my second shot was slightly higher at 184 fps so pretty close to the claimed 200 fps and that was in not the warmest of environments since the temperature in the Replica Airguns Sea Can Indoor Airgun Shooting Range was only 16 Degrees Celsius (60 Degrees Fahrenheit).
Next up it was time to see how the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun performed shooting at a target setup 30 feet away. Since there are no actual sights on the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun I had to kind eyeball it and as I shot it more and more I was able to get my shots closer to the center of the target. The Umarex T4E HDS Double Barrel CO2 Paintball Shotgun is not a tac driver but at 30 feet out you should be able to hit an 8-10 inch target pretty consistently. I don’t recommend using the double shot option since the same amount of CO2 is applied to both rounds that would normally be applied to one round decreasing the fps by about half making the paintball rounds shoot a lot slower and not really being that effective. This may be an option with the higher 300 fps version of the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun.
So all in all I had a lot of fun shooting the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun, it’s kind of like a big boy Nerf Gun that you can take onto the paintball field if you wanted to. For home defense I think it is a bit underpowered but there may be a little bit of shock factor that could slow someone down or deter them enough to either give you time get away or take shelter somewhere safe. Maybe using the pepper rounds would work OK in this situation? Either way the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun is a really cool and unique CO2 Airgun that is not overly expensive and a welcome addition to any Airgun enthusiasts collection.
Starting off with my velocity power test using my Caldwell Ballistic Precision Chronograph, I was able to get really close to the factory claimed fps of 360 with an average of 347 fps. Shooting conditions where decent in the See Can compared to outside temperatures in late October but still not that warm at only 16 Degrees Celsius (60 Degrees Fahrenheit), a lot warmer than outside but still not as warm as your typical summer day. In warmer conditions I am sure I would have hit the claimed 360 or even high fps with the Umarex Glock 19X CO2 Blowback BB Pistol.
Next for my Field Testing , I placed 10 shots into a paper target with my Umarex Glock 19X CO2 Blowback BB Pistol from 30 feet down range using my standard seated and rested shooting position (Seated in the back and rested on a sand bag up front). I was able to get right around a 2 inch 10 shot group, not bad at all! The Umarex Glock 19X CO2 Blowback BB Pistol did shoot a little bit high and to the left which for some reason is common with most CO2 action airguns and I know it’s not entirely me since others have commented the their airguns shoot a bit to the left in most cases. Elevation was pretty close at 30 feet but just a tad high.
The Umarex Glock 19X CO2 Blowback BB Pistol is very similar to their Umarex Glock 17 3rd Gen in terms of their mechanical build and function since both use the same magazines and have that semi blowback action but I can say the Umarex Glock 19X CO2 Blowback BB Pistol not only looks better in my opinion but the slide is improved as it seems to have a less metallic sound and the slide wiggle is very minimal. The Umarex Glock 19X CO2 Blowback BB Pistol also did not lack in the performance department getting really close to the the claimed 360 FPS while shooting about the same 10 round grouping of 2 inches which is about what I expect for an action BB shooter. Now we have a bunch of Umarex Glocks to chooses from, checkout our Replica Airguns Canada and US Online Stores for Glock airguns and find one that’s right for you!
The Umarex T4E HDS Double Barrel .68 caliber CO2 Paintball Shotgun is a two shot short barrelled that could come in handy for CQB engagements but it looks to be designed also as a none lethal home defence weapon since you can load a CO2 without piercing it but when in a bind you simply hit the CO2 screw and it pierces the CO2 activating the gun for instant use. I will have to test this one out to see if it really has enough power to stop an intrude, after all you only get two shots so they better count!
Type: Blowback CO2 BB Pistol. Manufacturer: Distributed by Umarex. Model:Glock 19X. Materials: Metal & Polymer. Weight: 1.5 pounds (662 grams). Barrel: Smooth bore 3.36 inch barrel (85.3mm). Propulsion: CO2 x 1. Action: Semi auto blowback, double action only trigger. Ammunition Type: 4.5mm steel BB's. Ammunition Capacity: 18 round drop out full size metal magazine. FPS: Claimed 360.
Trigger Pull: The trigger pull on the Umarex Glock 19X CO2 Blowback BB Pistol is what I would call a double action trigger mainly because there is an indexing of the BB from the magazine into the breach area every time you pull the trigger which means the take up is longer thanks a standard Glock take up and there is a little bit of friction from the mechanical mechanism that indexes the BB making the trigger feel more like a double action only trigger.
Build Quality: TheUmarex Glock 19X CO2 Blowback BB Pistol seems to be really well made. Fit and finish are nice and slide wiggle is minimal. There is a bit of a clanky sound when the slide cycles but not as bad as the Umarex Glock 17 Gen 3 CO2 Blowback BB Pistol. I also think the Coyote finish is the nicest looking with its black on tan two tone look.
Realism: The Umarex Glock 19X CO2 Blowback BB Pistol absolutely looks the part of a Glock 19X, sitting on the table and even holding it in your hand you are going to think it's the real deal until of course you drop the magazine and see that it is a CO2 mag. Mostly everything operates like a real Glock 17 but the slide is not a full blowback meaning it only goes back about 3/4 as much as a real Glock 17 slide would. One other noticeable difference is the ability to quickly field strip the Umarex Glock 19X CO2 Blowback BB Pistol, you will need to remove a pin since the take down tabs are non functioning and moulded into the frame. Available From: The Replica Airguns Store.
Pros:
Nice weight and feel to it, build quality seems good.
Really nice looking replica of the real steel Glock 19X, love the Coyote color.
Fully Glock licensed.
Easy to see white dot sights front and back.
Recessed barrel for added realism.
Accessory rail for adding a laser or tactical light.
Full size drop out metal magazine that holds the CO2 and 18 4.5mm steel BB’s.
Safety built into the serial number plate area keeps it well hidden.
Warning instruction are nice and discreet under trigger guard
Not bad feeling double action only trigger as the blowback pre-cocks the internal hammer/strike.
360 fps is decent for a blowback BB gun.
Cons:
Does have blowback action but not full blowback.
Slide sound is a bit clanky but not as bad as the 17 Gen 3 Blowback.
Sight are non-adjustable which is common with low cost action shooters like this one.
Would have liked to have seen more pristine packaging from Glock over the plastic clamshell
Comments:
It’s great to see Umarex expanding their live of Glock licensed Airguns and the addition of the Umarex Glock 19X CO2 Blowback BB Pistol is welcome! Some of you are not going to like the semi blowback action but it does mean you get higher fps and more shots per CO2 while still getting that simulated recoil form the blowback action. I honestly thing the Umarex Glock 19X CO2 Blowback BB Pistol is one of the most attractive Glock Airguns with it’s Coyote Tan frame and slide with black highlights, I also like the compact size for its shortened frame and slide over the Umarex Glock 17 Gen 3 CO2 Blowback BB Pistol. So many to choose for now but I guess that a good thing or perhaps just get them all!
