Materials: Mostly metal with some plastic construction.
Weight: 2.75 pounds (1218 grams).
Barrel: 5.5 inches, non-rifled.
Propulsion: 12 gram CO2.
Action: Revolver, single & double actions.
Ammunition Type: 4.5mm steel BB's.
Ammunition Capacity: 6 rounds.
FPS: 400fps.
Trigger Pull: The trigger pull on the Colt Python 357 CO2 BB Revolver is good in both single and double action, even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, most likely because the spring tension that pushes the inner barrel to make contact with the cylinder is noticeably lighter on the Umarex Colt Python 357. Even the hammer is smoother and has less wiggle, just a better trigger and hammer mechanism overall.
Accuracy: The results I got shooting my 6 round group from a 30 foot out semi rested position where good overall. Vertically there was about a 2 inch spread while horizontally there was about a 1 inch spread. I did find the plastic tips on the brass shells seemed to be a bit tight at first and this is when I did most of my Chronograph and target shooting. I believe the tightness effected the consistency of the FPS which also effected the accuracy especially up and down. I did get one shot out of the Umarex Colt Python 357 well over the claimed 400 fps but again the fps was rather erratic most likely because of the snug BB fit due to shell break-in.
Build Quality: The Umarex Colt Python 357 being mostly metal, you would expect it to have a decent build quality and I am happy to say it does, perhaps again even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, even the weight of the Colt Python came in close to a half of a pound more! The only real plastic I could find was in the grips and the shell tips. Fit and finish was also good with no noticeable paint wear or sloppy workmanship.
Realism: The Colt Python 357 CO2 BB Revolver overall is a close copy of the real steel Colt Python 357. I did notice the rear portion of the receiver (between the rear cylinder and hammer) to be a bit longer perhaps to accommodate the CO2 valve length, but other than that this pistol is super close to the original revolver it is based and licensed on. Agin being all metal gives this CO2 BB revolver very realistic weight and feel and the loadable brass shells make using this gun almost exactly like using a real shell loading revolver but for much less cost per shot and of course a lot less recoil on the hands.
It's a revolver with actual shells! Give you the feeling of loading and shooting a real revolver.
Mostly all metal design.
lots of detail, well made, fit and finish is very good.
Good overall weight, heaviest out of all the shell loaders.
Good overall power, accuracy and shots per CO2.
Fully adjustable sights for windage and elevation.
Well hidden CO2 Screw.
Recessed barrel.
Nice easy Trigger pull in both single and double action.
Cons:
Grips are a bit rough.
All black sights not great on dark backgrounds.
FPS seemed to fluctuate a bit
Comments:
The ASG Dan Wesson shell loading revolvers reintroduced me to the joy of loading and shooting a revolver which up until that point was not that realistic of an experience when using a BB or Pellet revolver. The Umarex Colt Python 357 has taken it up a notch by adding just a bit more overall weight, a smother trigger and hammer mechanism and styling this revolver on the Classic Colt Python platform. And all of this for even less than the cost of the original Dan Wesson shell loading series CO2 BB revolvers. If you're a revolver fan, make sure to grab one of these and if you're not a revolver fan, this pistol may just change your mind :)
My Vimeo Table Top Review for the Umarex Colt Python 357 CO2 BB Revolver:
I stopped by the ICS Booth, we don't sell too much of their products but have carried a few items from time to time. ICS caries some nice quality Airsoft guns including the M1 Grand with real wood stock, and some AK & AR variants.
One of our suppliers had the new FN Herstal Five-seveN Blowback Airsoft pistol, I believe made by Marushin. Like the real FN Herstal Five-seveN, the pistol is pretty much all polymer including the slide and frame. This pistol also uses CO2 in the full size drop out magazine which should make it fairly powerful.
Looks like there is another Dan Wesson contender available now in the form of a Swiss Arms S&W 357 Magnum 4 inch and 6 inch barreled version, they look really nice and like the Dan Wesson have the realistic reusable brass shells that hold the 4.5mm Steel BB's.
Ever considered owning a mobile Gunsmith vehicle, look no further, I came across this pimped out Firearms Van complete with machine guns mounted in the front :) Inside was a complete firearms workshop.
Last but not least, we had some fun while in Vegas. I go down for the SHOT Show for business but I also bring my wife and we make time for some non business related activities. I generally stay at the WorldMark resort each time and this year the weather was pretty nice so we where able to get some sun by the pool a couple of days and I even got a tan line! Of course the food and entertainment is always awesome in Vegas.
Trigger Pull: The trigger pull on the Umarex Smith & Wesson 357 686 Revolver is very light and smooth in both single and double action. Single action is much shorter and a bit lighter with just a very short take up to it. In double action it does get a hair heavier and much longer as is expected but still very usable and easy to shoot quickly and with accuracy.
Accuracy: I found the Umarex S&W 686 pellet revolver to have some of the best accuracy I have tested out of a pistol, getting about a half inch grouping from 30 feet out in a semi rested position (sand bag up front, standing in the back). I also put 5 rounds through my Chrony Chronograph and the Umarex 357 686 averaged right around 450 fps using RWS 7 grain lead pellets which is even better than the claimed 425 fps from Umarex.
Build Quality:The Umarex Smith & Wesson 357 686 CO2 Pellet Revolver is almost entirely metal with the acceptation of the rubber grips and front removable sight, it has a very substantial overall weight and feel to it coming in at just under three pounds. Keep in mind this is one of the higher end German made Umarex guns and you can tell in the workmanship and fit and finish. All the mechanical parts work flawlessly and have very tight tolerances, the finish is also superb. Yes the price is up there but this is a an airgun you will most likely be passing down to future generations one day as a collectors item, and I would imagine also in working condition.
Realism:The Umarex S&W 686 is a replica of the real stell Smith & Wesson 357 Magnum and overall looks pretty similar in shape and style. It would have been nice to have seen a full swing our cylinder but this would have meant a more complicated design with potentially less performance? In a perfect world, loadable shell casings like the Dan Wesson would have been very cool but keep in mind this is an airgun that really performs in terms of power and accuracy. Mine was the silver version, I would have liked to have seen a color matched magazine but since it is metal it could be color matched after the fact. The Smith & Wesson licensing and markings along with the heavy weight, hidden CO2 Tab and recessed barrel help to give the Umarex S&W 686 a very believable look and feel.
Pretty much all metal, has a nice solid feel and good weight.
Higher than claimed fps (right around 450 fps)
Amazing accuracy, one of my best pistols tested to date.
Very high quality German made workmanship.
Very comfortable rubber grips.
Fully adjustable rear sight (windage and elevation).
Well hidden CO2 tab.
Full S&W licensing, good overall replica.
Single and double action with a nice trigger in both SA and DA.
Magazines are removable for easy loading and have a high 10 shot load capacity.
Cons:
A bit on the expensive side of things.
Rotary magazine is not color matched on the Silver version.
On the low side of shots per CO2 (About 60-70).
No rail mount for a accessories of any type.
Comments:
The Umarex Smith & Wesson 686 CO2 Pellet Revolver is not for everyone and I say that because the $250 plus price point is going to be just too much for many buyers. If you can find a way to get past the price then you will have a very high quality German made air gun on your hands, not only are the Smith & Wesson 568/686 CO2 Pellet revolvers very well made but they also perform as good if not better in terms of accuracy and velocity then even some dedicated target air pistols I have tested. Looks will not let you down either and I would not be surprised that this gun if well taken care of can be passed down to future generations as a working collectors item. If you are looking for a high quality, excellent performing replica pellet revolver then make sure to consider the Umarex Smith & Wesson 586 and 686 line of CO2 replica pellet revolvers.
Trigger Pull: The trigger pull on the Crosman 357 is decent in both single and double action. Single action is much shorter and lighter but not overly light with just a very short break to it. In double action it does get heavier and much longer as is expected. People with small hands may have to adjust their grip so they will have enough extension for the entire trigger pull, this is partially because of the larger grips that sit far back on the revolver frame.
Accuracy: I found the Crosman 357 pellet revolver to have excellent accuracy, getting about a 1 inch grouping from 30 feet out in a semi rested position (sand bag up front, standing in the back). I also put 6 rounds through my Chrony Chronograph and the Crosman 357 averaged 402 fps using RWS 6.9 grain lead pellets.
Build Quality:The Crosman 357 CO2 Pellet Revolver uses a combination of metal and plastic and has a good overall weight and feel to it. There could be more metal (like in the outer barrel) but Crosman used metal parts where they really needed to be like in the main frame, trigger, hammer, CO2 area and inner barrel. This air pistol has been around for a long time and so you can count on all the bugs being worked out. You will not find a great amount of detail in the Crosman 357 and some of the joints seem a bit unrefined but overall it is a nice looking airgun and feels well made.
Realism: The Crosman 357 is a replica of the Colt Python 357 Magnum and overall looks similar in shape. I would have liked to have seen a full swing our cylinder but this would have meant a complete redesign and the Crosman 357 main design goes back to the early 80's. Yes there are some newer revolver styled airguns like the Dan Wesson that have full swing out cylinders (BB only) but I still would have liked to have seen this, maybe on a future updated revision?
Inexpensive Pellet revolver, not really any other pellet revolvers out there to compare to.
Good usage of metal parts. (Metal trigger, hammer, frame, barrel, CO2 tab screw).
Single and double action trigger.
Excellent accuracy and good power with a reasonable amount of shots per CO2.
Can mount optics on the dove tail railed barrel.
High capacity 10 round removable magazine.
Fully adjustable rear sight.
Cons:
Outer barrel is plastic.
Grips and trigger pull length may be a bit long for smaller handed people when shooting in double action.
Some of the finish detail could be better (seems).
A slight recess on the inner barrel would have added to the realism.
Comments:
Reviewing this fun Crosman Pellet revolver was a bit of a walk in the past for me. back when I was in my early teens I had one and it went with me on just about all of my back woods adventures. I'd have to say I learned how to shoot with this pistol and it felt right at home back in my hands after all these years... Back in the day I didn't do any scientific testing with my Crosman revolver but I can tell you it shot hard and true then, just like it does now! I'm not sure why I held out so long getting another one, the price is right and if you are looking for a nice multi-shot pellet pistol with excellent accuracy and good power for well under $100, the Crosman 357 might just be for you.
Sorry for not posting any videos for almost a week but the kids are back to school and I was also away in Whistler on a short family get away for the first half of the week. So I thought I would put together a quick Update video to show off some new products added to the Canada Replica Airguns Store and also an upcoming product review of a Crosman Pellet Revolver.
In this video Update I show you around two KWC Airsoft pistols, the Sig Pro SP2022, and the Taurus PT 24 (24/7), both of which I just added to the Canada Replica Airguns Store. I also show you a very nice alternative to the Cybergun Sig Sauer P226 X-Five - the KWC Equivalent which almost exactly the same but with an adjustable rear sight, flared magwell and an unlicensed slide.
One air pistol I get asked to review over and over again is the Crosman 357 .177 caliber pellet revolver and so I contacted Crosman and they where kind enough to send me one for review, so keep checking back for that one, it will be coming up soon.
Oh-yh, one more thing. I briefly mention an upcoming contest/giveaway that will coincide with my 10,000,000 YouTube Channel Video View that should be happening in the next couple of week!
Trigger Pull: The trigger pull on the Kimar Model K 760 is a bit stiff but on a beginner gun I would recommend the trigger to be on the heavy side for safety reasons and also to teach correct trigger control. It did not seem to effect my shooting at all which was nice.
Accuracy: Very good, I was surprised at the tight group I got from a semi rested position and with open sights, I nearly got a 3/4 inch group from 30 feet out which is about the best I can expect from just about any gun I have shot in the same manner. The Kimar Model K 760 spring piston break barrel rifle also shot true to it's claimed feet per second rating and got right around the 450 fps velocity mark.
Build Quality: The Kimar K 760 .177 air rifle is not going to win any prizes for style or craftsmanship but it gets the job done and in about as simple a manner as is required. With that said, what can really go wrong with it?Crank the barrel and pull the trigger. The lack of a safety does not really bother me as I never ever trust a safety and it's always good to learn how to keep a gun safe at all times even when you "believe" it is not loaded or ready to shoot. There is some plastic found on the Kimar K 760 like in the sights and the stock but the mechanical parts are all metal including the trigger.
Coming in at around $50, you can not ask the world from the Kimar Mod. K 760 .177 Caliber Spring Piston Rifle! What you can ask for is for decent accuracy and usable fps, and that's exactly what you are going to get from the Kimar K 760. This break barrel air rifle is really perfect for a beginner shooter on a budget or even for someone who may want to pack it around in some ugly situations where you wouldn't want to subject your high priced top quality air rifle. For the money you really can't lose with this one!
Looking for an ultra compact, super inexpensive, Italian made air rilfe for target or small pest control? Look no further!
This brand new air Italian made rifle from Kimar in .177 caliber is an ideal first air rifle for plinking targets in the back yard and because of it's very compact size it is excellent for small or first time shooters. Don't assume it doesn't have any power? You get up to 450fps velocities which makes the Kimar K 760 useful for shooting small rodents.
The Kimar 760 is very inexpensive yet has a high quality finish on the synthetic stock and metal work and fires accurate groups from 15 meters out with its open sights which are adjustable for windage and elevation.
