There are many types of magazines used in Airguns and some of this is dependent on the ammunition used.

For instance a stacked type of magazine often used for Steel BB and Airsoft can not be used for Pellets as pellets tend to deform when stacked in such a way since there is no metal casting protecting them from mashing into each other.

So what type of magazines do we generally see in Airguns? The most common Airgun magazines are as follows:

Simple Stick Magazine

• Mostly used with Steel BB but also found in some Airsoft Airguns.

• Some Pellet Airguns use a type of stick magazine with a rotary magazine on each end.

• Used in non-blowback and blowback Airguns.

• Can be made from plastic or steel or a combination of both materials.

Full Size Drop Out Magazine

• Used with Steel BB and Airsoft guns.

• Generally you will find these types magazines hold both the BB’s and CO2.

• Used in non-blowback and blowback Airguns.

• Commonly used with Airsoft Rifles in mid to high capacity.

• Can be made from plastic or steel or a combination of both materials.

Rotary magazine

• Used with Steel BB, Airsoft and Pellet Airguns.

• Used in non-blowback and blowback Airguns.

• Can be made from plastic or steel.

• Can often use mixed ammo types as in both 4.5mm Steel BB and .177 caliber pellet.

Belt Fed Magazine

• Like rotary magazine belt fed magazine can accommodate Steel BB, Pellet and Airsoft but are most often used with Pellet Airguns.

• Usually found in a full size magazine that also holds the CO2.

• Used in non-blowback and blowback Airguns.

• Can be made from plastic or steel or a combination of both materials.

Internal Magazine

• Used with Steel BB, Airsoft.

• Can have a hopper built in hat feeds a spring fed magazine.

• Usually found in lesser expensive Airguns but not a rule.

In this Video I go through each type of Airgun Magazine and talk about their differences and uses.

I have another Full Auto Fun Video this one focusing on 4.5mm Steel BB Versus 6mm Plastic and which one is better in terms of accuracy and shredding power. I perform this super scientific test by shooting obviously in full auto two comparable Steel BB and Plastic Airsoft Rifles at a paper target setup 20 feet away with a magazine as a backer so I can see what the accuracy is like and how much of the paper magazine gets shredded by each ammo being tested.

I have split this video into three separate videos, in video one I compare two similar AR styled rifles, a CO2 powered Blowback 4.5mm BB Rifle to a Gas Blowback 6mm Airsoft Rifle. In video two I compare two AK type Blowback Rifles to each otters, again a CO2 4.5mm Steel BB along with a Gas 6mm Airsoft.

And lastly in Video three I compare my top picks for each category which include a non-Blowback CO2 4.5mm BB Machine gun to an AEG 6mm Airsoft Rifle.

In this video (Video Three) the Airguns being used are the Original Baikal Drozd CO2 BB Machine Gun and the Tokyo Marui CQBR Block1 AEG Airsoft Rifle.

• Buy Airguns in Canada

• Buy Airguns in the US

In this Replica Airguns Video I talk about the latest Canadian Temporary Handgun Ban What it Means for Airguns. I talk about what I think abut it and what it means for Replica Airguns now and in the future.

Canada puts in place temporary handgun import ban!

From: Global Affairs Canada

News release

August 05, 2022 - Toronto, Ontario - Global Affairs Canada

Canadians deserve to feel safe in their communities. That is why the Government of Canada has a comprehensive plan that gets firearms off our streets and more

resources into our communities. A central part of this is the recently introduced Bill C21. The bill addresses the alarming role of guns in gender based violence, gets tough on organized crime and most significantly introduces a national freeze on the sale,

transfer and ownership of handguns, anywhere in Canada.

The Honourable Mélanie Joly, Minister of Foreign Affairs, and the Honourable Marco Mendicino, Minister of Public Safety, today announced a temporary import ban on the importation of restricted handguns. This will help bring the ultimate impact of the national handgun freeze into force sooner. This temporary ban means that individuals and businesses will no longer be able to import handguns into Canada, subject to narrow exceptions that mirror those in Bill C-21. These restrictions will take effect on

August 19th, 2022, and will last until the national freeze comes into force. No single program or initiative can tackle the challenge of gun violence on its own. That is why Bill C-21 and the national freeze on handguns are two of the many elements in the Government’s comprehensive plan to keep Canadians safe. This begins at our borders, where we’ve added resources to fight smuggling and stop guns from coming into Canada. We’re also investing in prevention programs to tackle the root causes of gun crime and stop it before it starts. Finally, we banned assault-style weapons like AR15s, and will soon begin a buyback program to get these weapons of war out of our communities once and for all.

Quotes

“We know that one Canadian killed by gun violence is one too many. As a government, it is our duty to ensure that Canada remains one of the safest places to live in the world. The import ban announced today will help to keep guns stay off our streets as we work towards implementing Bill C-21, reducing gun violence in the immediate term.

- Mélanie Joly, Minister of Foreign Affairs

“My top priority as Minister is keeping Canadians safe in their communities. Today’s announcement is further proof that we are using all tools at our disposal to fight gun crime in this country. It is a key pillar of our plan to address it, along with investments in prevention, action at our borders, a ban on assault-style weapons and Bill C-21 –Canada’s most significant action on gun violence in a generation.”

- Marco Mendicino, Minister of Public Safety

View fullsize

Type: Airsoft Rifle.
Manufacturer: Sig Sauer
Model: ProForce MCX Virtus.
Materials: Metal and Polymer.
Weight: 7 pounds (3kg).
Barrel: 11.6 inches (295mm).
Propulsion: AEG.
Action: Semi & Full Auto - SAO Electronic trigger.
Ammunition Type: .6mm plastic Airsoft BB’s.
Ammunition Capacity: 120 (Mid cap).
Max FPS: 408 Tested (.20 gram).

View fullsize

Trigger Pull: The trigger on the Sig Sauer ProForce MCX Virtus AEG Airsoft Rifle is essentially a Single Action Only electric on off switch that can allow for semi and full auto shooting along with a safety position based on the sector switch position. Because of this it is fairly short and light weight. There can be a slight delay from the time you pull the trigger to when the BB is released as since the electric motor needs to first pull back the internal spring before being released. A higher voltage battery will shorten the time between your trigger pull and the Airsoft BB release. Higher voltage battery also increases the full auto cycle rate.

View fullsize

Accuracy: I did already perform my Field Test Shooting Video for the Sig Sauer ProForce MCX Virtus AEG Airsoft Rifle so I do have some information to share relating to the shooting abilities of this AEG Airsoft Rifle. During my Velocity Chronograph Test I was able to average 408 fps using .20 gram Airsfot BB’s, that was using the out of the box installed 120 spring. In terms of accuracy, my 10 shot grouping at 30 feet away yielded a 1.5 inch spread and when I placed the Sig Sauer ProForce MCX Virtus AEG Airsoft Rifle in full auto it did not open up that much more, only to around 2 inches since there is virtually no recoil to throw off full auto shot placement. You can watch my full Field Test Shooting Video here!

View fullsize

Build Quality: The build quality of the Sig Sauer ProForce MCX Virtus AEG Airsoft Rifle is exceptional with high quality material inside and out, this Airsoft Rifle is mostly metal with a CNC machined receiver and a hefty 7 pound weight to it. Internally you will find VFC Avalon Gearbox featuring improved bearings, quick change spring system, built in MOSFET, and powered by high torque neodymium magnet motors.

View fullsize

Realism: The Sig Sauer ProForce MCX Virtus AEG Airsoft Rifle is designed and licensed by Sig Sauer to be as close to their real steel version of the MCX Virtus as possible in every way. As expected you will find Sig Sauer and Virtus licensing all over, size, handling and weight are also true to the original.

View fullsize

Pros:

• Super high quality AEG Airsoft Rifle.

• Bolt locks back for easy hop-up adjustments.

• Sig Sauer designed and licensed.

• Lots of metal parts including the CNC machined metal receiver, rear stock guide rails and most mechanical moving parts.

• Lots of mounting points with it’s full length picatinny top rail with M-LOK handguard.

• Awesome internals, VFC Avalon Gearbox, quick change spring system, built in MOSFET, high torque neodymium magnet motors.

• Easy to mount a sling with it’s QD tactical sling mounts on handguard, lower receiver, and stock.

• Performed well in the Field test hitting close to claimed fps and easily shooting a 1.5 inch 10 shot group for 30 feet away.

View fullsize

Cons:

• No included sights so you will need to add your own iron, red dot or optical sight.

• Battery area is a bit tight so you will need fairly compact batteries.

• Comes with orange flash hider but can be swapped out.

• On the high end of the price spectrum.

View fullsize

Comments:
The Sig Sauer ProForce MCX Virtus AEG Airsoft Rifle is not only a looker but also a performer and is one of the higher quality AEG AR Styled Airsoft Rifles out there. I know there are a ton of AR AEG Airsoft Rifles to pick from but if you want something a little bit different then the rest than the Sig Sauer ProForce MCX Virtus AEG Airsoft Rifle is for sure one to look at. It is a bit more money up front but will offer exceptional performance and the high quality internals will not only perform well but will last the test of time saving you money long term.

• Buy the Sig Sauer Proforce MCX Virtus AEG Airsoft Rifle in Canada

• Buy the Sig Sauer Proforce MCX Virtus AEG Airsoft Rifle in the US

View fullsize

Yet another Indoor Field Test Shooting Video performed in the Replica Airguns Sea Can Airgun Shooting Range. Today I put the Sig Sauer Proforce MCX Virtus AEG Airsoft Rifle through its paces and it came out a winner for sure! I really like the way this AR15 type AEG Airsoft Rifle looks and feels and was hoping to get a good result today, I was not disappointed! I have not yet made my Table Top Video for the Sig Sauer Proforce MCX Virtus AEG Airsoft Rifle but plan for this next week, you can watch my Preview Video for some details and specifications in the mean time…

As I always do, I first tested out the Sig Sauer Proforce MCX Virtus AEG Airsoft Rifle by shooting several rounds through my Chronograph to see what the actual velocity is in fps. I used .20 gram Airsoft BB’s for this test and was able to get a 6 shot average of 408 fps so perfect for most shooting situations as this is not too hot or too cold. My slowest shot was 402 fps while the fastest shot was 410 so pretty consistent for sure.

View fullsize

Next I placed a fresh paper target 30 feet down range on my ammo trap and proceeded to shoot around 10 rounds into it using a rested seated shooting position with a sand bag up front to help with stability. The first shot out of the barrel felt and sounded like a double shot and this one did strike the target just a tad low so I left that one out of the test results. All the other Airsoft BB’s shot easily within 1.5 inches maybe even a bit tighter and all where well centered left to right but just a bit low on the target most likely because I was using a red dot with a riser that places the sights fairly high. Since the Sig Sauer Proforce MCX Virtus AEG Airsoft Rifle can also shoot in full auto I had to give it a try and pretty much emptied the magazine until the target actually fell off the ammo trap. The full auto grouping did open up just a slight bit as expected but only marginally.

I really like the Sig Sauer Proforce MCX Virtus AEG Airsoft Rifle, yes it’s an AR15 at it’s core but Sig has made it their own in terms of looks and styling. The performance was also excellent so this gun is not just for show. You will need a sighting system of some sort when you buy it so keep that in mind. I suggest a red dot of some sort but you could add on iron sights if you like more traditional sights.

• Buy the Sig Sauer Proforce MCX Virtus AEG Airsoft Rifle in Canada

• Buy the Sig Sauer Proforce MCX Virtus AEG Airsoft Rifle in the US

In this Preview Unboxing Video I take a look at three rifles, two are Airsoft Rifles and one is an Archery Rifle. Then First Airsoft Rifle form Tokyo Marui i s full Gas Blowback all metal build AR 15 of the highest quality and realism while the second Airsoft Rifle from Sig Sauer is an AEG but again a high quality product for sure. Lastly I take a look at Umarex’s lates Airsaber which now sports dual Arrow configuration for quick follow up shots. I do plan to make future more intensive table top and shooting videos for some if not all of thees Rifles but this video will at least wet your appetite a bit.

View fullsize

Tokyo Marui CQBR Block 1 GBB Airsoft Rifle:

• Type: GBB Airsoft

• Caliber 6mm Airsoft

• FPS: 350-400

• Magazine Capacity: 35

• Weight: 9.9 pounds

• Length: 27.5 inches

• Material: Mostly Metal

• Action: Semi & Full Auto

View fullsize

Sig Sauer Proforce MCX Virtus AEG Airsoft Rifle:

• Type: AEG Airsoft

• Caliber 6mm Airsoft

• FPS: 420

• Magazine Capacity: 120

• Weight: 7 pounds

• Length: 29 inches

• Material: Mostly Metal

• Action: Semi & Full Auto

View fullsize

Umarex Airsaber Elite X2 Archery Rifle:

• Type: PCP Archery

• Capacity: 4000 PSI / 240 CC Tank

• FPS: 450 / 169 ft-lbs

• Ammo Capacity: 2

• Weight: 8.7 pounds

• Length: 42.5 inches

• Material: Metal & plastic

• Action: Side cocking lever

View fullsize

I know this is an Airgun channel but when I get something that I feel my audience would be interested I in, I generally share it with everyone. I know many Airgun enthusiasts are interested in Airguns for a few reasons like the lower cost to buy and operate, the fact that there are more situations where you can shoot an Airgun and perhaps availability of these guns in terms of purchasing them without a license and laws pertaining to overall size, barrel lengths, magazine capacities and the likes. My latest acquisition does tick some of these boxes for sure.

View fullsize

My latest “Birthday” purchase was the GSG-16 which is a 22LR rimefire rifle made by www.GermanSportGuns.com and it is sort of an MP5 copy but this version is more like a Frankenstein version of an MP5 combined with an AR-15 in order to make H&K happy. Previous version of the GSG-16 (the GSG-5 and GSG-522) where too similar to the MP5 and so GSG had to make a third version less MP5-ish.

View fullsize

That said the GSG-16 has all the same controls as the MP5 so for training purposes it would be very suitable. Personally I like what GSG did in order to bring the GSG-16 to market without legal ramifications from H&K. I like all the rails and the way it kind of looks a bit more like an AR-15 even if the controls are not the same.

View fullsize

If you do like the MP5 look there are some kits out there for the GSG-16 to turn it back into more of an MP5 looking rifle but for me I don’t need to spend the extra money to be happy with the GSG-16.

No we do not have this item in our Replica Airguns Stores as we really only cater to guns that do not require any sort of lisenceing or permits. The closest thing you can buy I would say would be either the Umarex HK MP5-PDW CO2 BB Rifle, one of the MP5 Airsoft Rifles we have or even the Crosman MPW Blowback CO2 BB Rifle which is more AR based.

View fullsize

This was an unusual Field Test Review for me to do as I really don’t test out Bows or Crossbows all that much and I don’t have the best backstop setup for doing such reviews. So I spent some time making a backstop that was capable of stopping these just over 6 inch almost 10 gram or 150 grain bolts. It required some layers of foam and cardboard along with a blanket behind just in case, and even with this setup the bolts managed to lodge themselves right up to the Fletching (feather part of the arrow). Also make sure to watch my Table Top Video Review for the Bear X Desire XL Crossbow to see it up nice and close and get all the specifications and features.

I kind of wanted to change up this review just a bit and so I recorded my Chronograph Velocity at the same time as I did my Target or Accuracy Test to simplify things. I used 5 bolts in all and got what I felt was a good result using the Bear X Desire XL Crossbow.

In terns of velocity Bear X claims that the Bear X Desire XL Crossbow will shoot around 175 fps. I was able to get consistent 190+ fps readings using the 147 grain 6.5 inch aluminum bolts with my lowest fps being 192 and the highest being 194 so super consistent. This gave an overall Foot Pound energy of 12.4 foot pounds! This is enough for small pests for sure, it really comes down to accuracy at this point as you will want to get either a head or shoulder area shot for a humane kill.

View fullsize

I did do a pre test to make sure I was on target and duding this test I was able to get about a 5 inch 5 shot grouping. During my recored Accuracy Test this did open up a bit as one arrow went high and to the right so if I leave that arrow out of the test I did manage to get another 5 inch grouping with three of the arrows all within 1.5 inches of each otter. I figure with high quality arrows and some practice time using the Bear X Desire XL Crossbow, you should be able to use it for small pest control at least at closer in ranges.

All in all the Bear X Desire XL Crossbow surprised me with how powerful it really was and with the accuracy using standard default bolts. This is for sure not a toy and you would never want to accidentally shoot this at someone as it could cause a very serious injury or even death and I mean that since these arrow would for sure pierce several inches into the body. So if you’re looking for something with a bit more raw power than your standard non-regulated Airgun, then check out the Bear X Desire XL Crossbow over in both our Canada and US Online Replica Airguns Stores.

• Buy the Bear X Desire XL Crossbow in Canada

• Buy the Bear X Desire XL Crossbow in the US

View fullsize

Type: Compact Crossbow.
Manufacturer: Bear X.
Model: Desire XL.
Materials: Metal & plastic.
Weight: 2.3 pounds (1 kilograms).
Length: 20-22 inches.
Propulsion: Bow.
Action: Single action trigger.
Ammunition Type: Aluminum bolts (Comes with 3).
Ammunition Capacity: 1.
FPS: 175fps.
Draw: 60 pounds

View fullsize

Trigger Pull: The trigger pull on the Bear X Desire XL Crossbow is medium to heavy, it is a single action only trigger as you need ot cock the bow in order for the trigger to be engaged. The safety is also engaged when you cock the bow requiring you to take the Bear X Desire XL Crossbow off safe before shooting as an added layer of safety.

View fullsize

Accuracy: I have not made my Field Test Shooting Video for the Bear X Desire XL Crossbow and so I have not sea what to expect for it. I have watched a few videos of other people reviewing it and it looks to perform fairly well but until I get a few bolts in a target downrange I can not say for certain the accuracy of the Bear X Desire XL Crossbow. I will have to figure out some sort of a usable back stop in order to make this Field Test Shooting Video but have some ideas already on material to use as my back stop. FPS is claimed ot be around 175 and I will be doing my best to Chronograph the Bear X Desire XL Crossbow so we can confirm that rating for ourselves…

View fullsize

Build Quality: The Bear X Desire XL Crossbow is actually made pretty decently, yes it is mostly plastic and light weight but feels sturdy enough to hold, the only real metal I can confirm is the cocking rail, mostly everything else other than the nuts and bolts that hold it together are some sort of plastic, the bow itself may be a composite material but I am not sure what exactly it is?

View fullsize

Realism: The Bear X Desire XL Crossbow is not a Replica as is what I usually review here on the channel. But I think their is a crossover in terms of interest for a product like this with people that are also interested in airguns. I know I like the Bear X Desire XL Crossbow and can see a place for it in my collection even if it’s not a replica product.

View fullsize

Pros:

• Fairly inexpensive.

• Super light weight.

• Can shoot in a variety of situations.

• Easy to draw the bow.

• Safety is automatically engaged.

• Picatinny rail already has iron fully adjustable rear sight but can mount a red dot if you like.

• Fiber optic front sight.

• 3 bolts included.

• 175 fps (not sure of the ft/lbs)?

• Comes with fore grip.

• 3 portion adjustable rear but stock.

View fullsize

Cons:

• Will need a good backstop or will lose or damage a lots of bolts.

• Takes a little bit of time to set it up but not too hard if you follow the instructions.

View fullsize

Comments:

The Bear X Desire XL Crossbow is an interesting product that once purchased and if you manage to not lose the bolts will cost virtually nothing to shoot since you can reuse the bolts all day long given you shoot them on target and that target does not damage the bolts. It may not offer the rapid fire action shooting of a replica semi auto CO2 Pistol but still challenges the shooter in terms of getting the best possible accuracy out of it and at the end of the day trigger time is trigger time! If you are looking for something a bit different than your CO2 Air Gun then maybe the Bear X Desire XL Crossbow will fill that requirement.

• Buy the Bear X Desire XL Crossbow in Canada

• Buy the Bear X Desire XL Crossbow in the US

In this Preview Unboxing Vimeo Video I take a look at five very different products! A Spring Piston .177 Caliber Pellet Pistol, an Airsoft GBB Pistol, a Compact Crossbow, a full auto CO2 Blowback BB Pistol and a PPC .22 Caliber Pellet Rifle.

View fullsize

First up is the Umarex Ruger Mark IV Spring Piston Pellet Pistol which is a single shot replica pellet pistol that shoots .177 caliber pellets at up to 320 fps using a spring piston break barrel system. The Umarex Ruger Mark IV Spring Piston Pellet Pistol is a target plinker with fully adjustable fiber optic sights and should be a lot of fun to shoot!

View fullsize

Next I take a look at a Gas Blowback Airsoft Pistol from Action Army that closely resembles the Ruger Mark IV pistol with perhaps a more compact look. The Action Army AAP-01 GBB Airsoft Pistol is full blowback a full size drop out magazine and fiber optic sights. It also come with a threaded barrel and barrel extension for adding a longer barrel and much suppressor.

View fullsize

Next on my list of new items is the Bear X Desire XL Crossbow which is a 2.2 pound compact bolt shooting crossbow that sports a rail system with included adjustable iron sights that also allow for a red dot if you want to really customize it. The Bear X Desire XL Crossbow has a 60 pound draw and shoots arrows/bolts at up to 175 fps.

View fullsize

Another AR BB Rifle/Pistol from Crosman is the Crosman A4-P Full Auto CO2 BB Pistol which is essentially a pistol version of the AR Platform. If you like the Crosman DPMS SBR, R1, PDW then you will probably also like the Crosman AP-4. Like the others it uses dual CO2’s and shoots 4.5mm Steel BB;s in semi or full auto at 1400 rounds per minute until the 25 round magazine is empty.

View fullsize

Last included in this preview video is the Air Venturi Avenger Regulated PCP Pellet Rifle. I’m a bit uncertain about this one as I am pretty sure it is the non detuned PAL version that requires a firearms license here in Canada as it shoots at full velocity (.22 caliber pellet at 950 fps). If that’s the case then it will not be available in our Canada Replica Airguns Store but may be available in the US Replica Airguns Store. If it is the detuned version or a detuned version becomes available in Canada then I imagine we will at some point have it in the Canada replica Airguns Store. That said the Air Venturi Avenger Regulated PCP Pellet Rifle uses compressed air and shoots either .177. .22 or .25 caliber pellets using a latch system and rotary magazine.

View fullsize

In this Replica Airguns Field Test Shooting Video I test out the Cybergun Kalashnikov AK47 Tactical Folding Stock AEG Airsoft Rifle to see what the actual velocity is and what kind of accuracy we can expect shooting 30 feet down range into a paper target, I shoot in both semi auto (10 rounds) and then Full auto (A bunch of rounds) to see how this will asl effect the accuracy.

Make sure to also watch my Table Top Video Review for the Cybergun Kalashnikov AK47 Tactical Folding Stock AEG Airsoft to find out more about it’s specifications and features along with some nice close up video of it.

Starting off with the velocity portion of this Field Test Shooting Video, I placed 6 rounds through my Chronograph using .20 gram Airsoft BB’s and averaged 384 fps. The slowest shot was 380 fps while the fastest shot was 390, so only a 10 fps spread! This is a nice velocity as it’s not too hot for indoor skirmishes or too slow for further out shooting outside.

View fullsize

Next I setup a fresh paper target 30 feet down range and proceeded to test out the Cybergun Kalashnikov AK47 Tactical Folding Stock AEG Airsoft Rifle in both semi auto and full auto to see what kind of grouping I could expect. I did not sight in the Cybergun Kalashnikov AK47 Tactical Folding Stock AEG Airsoft Rifle as I like to see how they perform right out of the box. I did notice I was shooting a little bit high and just slightly to the left. Elevation adjustment can be easily adjusted using either the front post sight, the rear notch sight or even a little bit with hop-up so this is not a problem. There is however no way I could see to adjust windage so any corrections you may need ot make left to right you will have to do using your aim point. That said I was able to get around a 1.5 inch grouping with 10 rounds in semi auto mode.

View fullsize

Switching things up to Full auto so fun mode I proceeded to place a whole bunch of rounds into the target, I will estimate around 75 or so and the grouping only spread out to about 2 inches so semi or full auto you will get great accuracy with the Cybergun Kalashnikov AK47 Tactical Folding Stock AEG Airsoft Rifle! The rate of fire using an 8.4 volt battery is not super fast but the cycle rate on a real steel AK47 is also not super fast but if you want to speed it up and also have a more responsive trigger then I would suggest using a higher voltage LiPo battery.

I was very impressed overall with the Cybergun Kalashnikov AK47 Tactical Folding Stock AEG Airsoft Rifle as it is a relatively inexpensive Airsoft Rifle with lots of included bonuses like two magazines, a battery and charger. Even with the low price and bundled add ons it performed really well for me. SO if you are looking for an AK type Airsoft Rifle I would suggest you take a look at the Cybergun Kalashnikov AK47 Tactical Folding Stock AEG Airsoft Rifle as an option for sure!

• Buy the Cybergun Kalashnikov AK47 Tactical Folding Stock AEG Airsoft Rifle in Canada

• Buy the Cybergun Kalashnikov AK47 Tactical Folding Stock AEG Airsoft Rifle in the US

View fullsize

Type: Airsoft AEG.
Distributer: Cybergun
Model: Kalashnikov AK47 Tactical 60th Anniversary.
Materials: Metal and polymer build.
Weight: 6.82 pounds (3100 grams).
Barrel: 457mm (18 inches)
Total Length: 709-950mm (27.9-37.4 inches).
Propulsion: AEG.
Action: Semi, full auto.
Ammunition Type: .6mm plastic Airsoft BB’s.
Ammunition Capacity: 550 rounds.
FPS: 400.

View fullsize

Trigger Pull: The trigger pull on the Cybergun Kalashnikov AK47 Tactical Folding Stock AEG Airsoft Rifle is what you will find on most electric switch controlled AEG Airsoft Guns. It has a short to mid length very light take-up with a light release which generally has a bit of a delay as the motor pulls the spring back and release the piston. This delay is shorter with higher voltage batteries as the motor will run quicker allowing for a shorter delay and also a higher rate of fire in full auto mode.

Accuracy: I have not performed my Field Test Shooting Video for the Cybergun Kalashnikov AK47 Tactical Folding Stock AEG Airsoft Rifle but plan to get to that video this week. I really have no idea what to expect at this point since i have not even loaded up a magazine so we will find out together when I get to my Indoor Field Test Shooting video in a couple of days.

View fullsize

Build Quality: Overall the Cybergun Kalashnikov AK47 Tactical Folding Stock AEG Airsoft Rifle seems fairly well built. You will find metal parts in the barrel, front and back sights, receiver, charging bolt, bolt cover, rings, trigger and trigger guard. The plastic components would be the folding stock, magazine, RIS hand-guard, fore-grip and pistol grip. Fit and finish seem good and the overall weight is heavy but not too heavy. Internally you get a metal gear box with metal gears so you should expect to have a reliable and long lasting shooting experience with this Airsoft Rifle.

Realism: The Cybergun Kalashnikov AK47 Tactical Folding Stock AEG Airsoft Rifle for sure looks the part of a more modern tactical AK47 with the majority of the mechanical parts functioning like a real steel version as in the charging bolt, bolt cover, sector switch, foldable rear stock and of course the magazine release.

View fullsize

Pros:

• Mostly metal construction with good overall weight and feel.

• Lots of rail attachment options on RIS rail hand-guard.

• Adjustable sights, smaller increments on front, easy quick adjustment for elevation at distance on the back.

• Comes with a folding fore-grip.

• Rear folding stock helps to shorten up the rifle in transport or for storage.

• Comes with two high capacity magazines.

• Comes with a battery and charger.

• Comes with sling mounts and a basic sling.

• Super easy access to change out the battery.

• Easy access to hop-up via charging bolt.

• FPS should be nice and high, good for long or mid range shooting.

• Cybergun Kalashnikov licensed, also 60th Anniversary edition.

• Orange tip should be easy enough to remove.

• Price point is fairly good for all that you get.

View fullsize

Cons:

• No simulated blowback action.

• Sights are only adjustable for elevation. 

• Magazines are plastic, feel a bit cheap and light.

View fullsize

Comments:
The Cybergun Kalashnikov AK47 Tactical Folding Stock AEG Airsoft Rifle is what I would consider a great value AEG Airsoft Rifle and there are not as many AK style Airsoft Rifles to choose from as there are AR’s so it’s nice to see this one in the lineup. You do get a lot for what you are paying, lots of metal parts externally and internally with a hefty almost 7 pound weight to it. I also like that you get everything you need to get going other than the Airsoft BB’s, so you get the battery and charger along with two 500+ magazines, they even add in a cheap sling just in case you want to throw it over your shoulder!

My Vimeo Table Top Review Videos for the Cybergun Kalashnikov AK47 Tactical Folding Stock AEG Airsoft Rifle:

• Buy the Cybergun Kalashnikov AK47 Tactical Folding Stock AEG Airsoft Rifle in Canada

• Buy the Cybergun Kalashnikov AK47 Tactical Folding Stock AEG Airsoft Rifle in the US

After about 4 years or so of not getting sick at all, I was almost starting to think I was impervious to viruses and colds and flues and then it finally happened… I got the Rona.

Now I am not 100% sure if it is the Rona since I have not been tested yet but all signs indicate it’s probably Omicron. I have ordered some antibody tests that I expect to come in shortly, I will be checking my blood for Covid-19 Antibodies once I know my body has had enough time to make them after getting sick this time.

In this video I talk about my symptoms and how I felt start to finish getting the Rona. I can say at least for me it was not big deal, the soar throat was probably the worst of it for me.

View fullsize

Took me a while to get to this Field Test Shooting Video for the ASG CZ Scorpion EVO 3 A1 6mm AEG Airsoft Gun but glad I took a look at it even if it is over 6 years already on the market. As per usual I test out the velocity shooting several ordains through my Chronograph to see what the real world fps is, I then follow this up with an accuracy test shooting 10 rounds on a paper target setup 30 feet downrange to see how tight of a grouping I can get. Also make sure to watch my Table Top Video for the ASG CZ Scorpion EVO 3 A1 6mm AEG Airsoft Gun for information on the specifications and features along with some nice close up video.

Starting with my Velocity Test I placed 6 rounds through my Chronograph using .20 gram Airsoft BB’s clocking in an average of 421 fps. I was very impressed with the consistency of the velocity with the lowest shot being 420 fps and the fastest shot being 422 fps only 2 fps apart! You can change out the spring super easy on the ASG CZ Scorpion EVO 3 A1 6mm AEG Airsoft Gun but I feel that the fps out fo the box would be good for most Airsoft games indoor and outdoor.

View fullsize

I then places a brand new paper target 30 feet downrange and proceeded to shoot 10 rounds at it in semi auto using a seated shooting position rested on a sand bag up front. I was able to get very close to a 1 inch grouping just a tad over an inch. I did not sight in the gun so I was not surprised I was shooting rather low and just a hair to the left, this could be equally corrected by adjusting the rear sight for windage and elevation. I could also play around with the hop-up effecting elevation at different ranges. I then proceeded to shoot take some more shot in both 3 round burst adn full auto modes and as expected the groupings did spread out a bit but not a lot.

I was super impressed with eh performance of the ASG CZ Scorpion EVO 3 A1 6mm AEG Airsoft Gun, I don’t think I have seen velocity consistency this good in any other AEG Airsoft gun I have tested so far. Accuracy was also on point even using lighter plastic .20 gram Airsoft BB’s. My only real grip with the ASG CZ Scorpion EVO 3 A1 6mm AEG Airsoft Gun is the limited battery choice since the internal storage ares is very constricted. Other than that this Airsfot Gun is a winner and worth taking a look at if you can get your hands on one.

• Buy ASG Products in Canada

• Buy ASG Products in the US

View fullsize

Type: Airsoft AEG.
Distributer: ASG.
Model: CZ Scorpion EVO 3 A1.
Materials: Metal and polymer build.
Weight: 5.3 pounds (2400 grams).
Barrel: 208mm (8.2 inches)
Total Length: 425-623mm (16.7-24.5 inches).
Propulsion: AEG.
Action: Semi, burst, full auto.
Ammunition Type: .6mm plastic Airsoft BB’s.
Ammunition Capacity: 75 rounds.
FPS: 395.

View fullsize

Trigger Pull: The trigger pull on the ASG CZ Scorpion EVO 3 A1 6mm AEG Airsoft Gun is essentially just an on off electric switch controlled by the ECU. There is very little trigger resistance and the take up is very short allowing for quick semi auto shooting but if you like you can easily select three round burst or full auto shooting for more intense situations.

Accuracy: I have not performed my Field Test Shooting Video for the ASG CZ Scorpion EVO 3 A1 6mm AEG Airsoft Gun but plan to get to that video next week. I really have no idea what to expect at this point since i have not even loaded up a magazine and taken it for a spin yet. I am sure I will not be dissapoitned as this is a very high quality Airsoft Gun with great internals.

View fullsize

Build Quality: I remember at SHOT Show back when ASG introduced the ASG CZ Scorpion EVO 3 A1 6mm AEG Airsoft Gun, I was told indirectly that the construction was nearly identical to the real steel CZ Scorpion EVO at least cosmetically as all the internal parts will be specificities to Airsoft. That said this is a very high quality build with the material being for the most part the same as the original with Nylon Fiber PA6 Polymer reenforced plastics and even some CNC machined metal parts as in the outer barrel, flash hidden, barrel nut and even the gear box.

Realism: The ASG CZ Scorpion EVO 3 A1 6mm AEG Airsoft Gun is a bang on replica in terms of emulating the real steel CZ Scorpion EVO and has our weight and feel including a blot catch that locks back when out of ammo and most working components being ambidextrous.

View fullsize

View fullsize

Pros:

• Build quality is almost exactly like the real steel version, super high quality materials.

• Three shooting modes: semi auto, burst mode and full auto.

• Decent mid capacity 75 round magazine with auto empty detection which locks the bolt catch.

• Quad rail for lots of add on accessories.

• Folding and adjustable stock that can also be removed.

• Adjustable and removable iron sights with fiber optic up front and peep in the back.

• Working charging handle for easy access to hop-up

• Working bolt catch.

• High quality electronic and gear box.

• Ambidextrous controls for the most part.

• Scorpion licensed through ASG.

• Orange tip is fairly discreet.

Cons:

• Battery compartment is small and hard for quick battery replacement, I recommend using an external setup if possible.

• Price point is on the higher side but you get what you pay for.

View fullsize

Comments:
On paper and just by looking over and inspecting the ASG CZ Scorpion EVO 3 A1 6mm AEG Airsoft Gun specs out and I am sure I will be pleased when I test it out in the Replica Airguns Indoor Shooting Range. That said this hasn’t happened yet so I will leave my final thumbs up until then. I do wish we had them in stock at the time of this video but there are a lot of other great ASG products in our store and of course many more brands of AEG Airsoft Guns. Hopefully we can get something like this in shortly for everyone so keep checking with us.

My Vimeo Table Top Review Videos for the ASG CZ Scorpion EVO 3 A1 6mm AEG Airsoft Gun:

• Buy ASG Products in Canada

• Buy ASG Products in the US

View fullsize

Wow, an accessory review, not many of these :) Today I take a look at the Amomax Airsoft Airgun Holster product line since at some point you may want to put your gun in a holster or practice drawing your gun from a holster?

The good news is we just got in a decent amount of product for our Amomax Airsoft Airgun Holsters. Here is a bit of info about Amomax but of course make sure to watch the video as I take a good look at a few of the versions we sell in our Canada and US online Replica Airguns Stores.

View fullsize

Amomax holsters are compatible with 4 different carrying platforms :paddle (standard), belt clip, MOLLE, and drop leg platforms. All the carrying platforms can be replaced by only one screw. Users can carry them in daily use, outdoor sports, normal shooting training and competition. Holster will stay firmly on a belt, leg and MOLLE system even in fast moving situations with a quick release Retention System button that keeps the gun locked in place until you are ready to draw. Holster body and carrying platform are connected with a tooth gear that allows for 360 degrees of rotation. User can easily adjust the carrying position to fit their needs.

View fullsize

Amomax Holsters are currently available in the following versions:

• Glock 17/22/31

• 1911 (Fits most brands 1911’s)

• USP

• Sig P320

• Single and double Universal Magazine

• Buy Amomax Airsoft Airgun Holsters in Canada

• Buy Amomax Airsoft Airgun Holsters in the US

View fullsize

As with most of the new tech I purchase or acquire that I will be using in my Videos for either my GetFitOver40 or ReplicaAirguns YouTube channels, I generally like to do some sort of a practical review for the item. In this case I take a look at the Synco G1 (A2) Wireless Microphone Set which is a pair of wireless transmitters that pair with a single dedicated receiver allowing me to quickly and easily capture good quality audio for my Videos.

For the past couple of years my go to microphone setup for my video was to use a generic lapel mic connected to my Samsung Galaxy Smartphone recording into an audio program. I would then send the audio file via dropbox to my computer where I would then line up the audio file with the video file in my video editing software to get a much higher quality and more clear voice recording versus what the camera mic would be able to capture.

This system has been working fairly well for me but required a somewhat cumbersome lapel cable and of course my bulky Smartphone in my pocket at all times but did allow me to be as far away from the camera as I wanted without any interference or loss of audio clarity.

View fullsize

After playing around with the Synco G1 (A2) Wireless Microphone System I have determined I will most likely simply be clipping the transmitter onto my shirt without the lavaliere mic plugged in and transmitting the audio into either my Samsung Smartphone or my iPad where I can then again dropbox the audio file to wherever I plan on editing the video.

This video was kind of a test to see how everything sounded in terms of the lapel mic versus the built in mic. What settings to use and how distance effected the audio signal and quality. Unfortunately the lapel mic was a bit close to my voice causing some distortion to occur but you can still hear what I am saying no problem. In the future I would place the lapel mic a bit further away from my voice lower down on my shirt or simply use the built in mic as it was not as sensitive to this distortion and seemed to handle louder volume much better than the lapel mic.

View fullsize

Here are some of the specifications for those that like that sort of info :)

Transmitter (TX )

• Wireless Transmission - Digital 2.4GHz

• RF Frequency Band - 2400-2483.5MHz

• Working Distance - 164ft/50m (LOS area) 98ft/30m (NLOS area)

• Latency - 12.5ms

• Mounting - Pocket Clip

• Audio Input - 1/8" / 3.5 mm TRS Mic Input

• Audio Input Level - 1V (0dBV)

• RF Output Power - ＜10mW

• Power Requirement - 3.3V-4.7V

• Battery Type - Built-in Lithium Battery

• Battery Charging Time - 1.5h

• Battery Life - 5h

• Dimensions - 52X42X16mm

• Material - Plastic

• Weight - 35g

Receiver (RX)

• Wireless Transmission - Digital 2.4GHz

• RF Frequency Band - 2400-2483.5MHz

• Approximate RF Sensitivity - -81dBm

• Working Distance - 164ft/50m (LOS area) 98ft/30m (NLOS area)

• Latency - 12.5ms

• Mounting - Pocket Clip

• Number of Audio Channels - 2

• Audio Output - 1/8” / 3.5 mm TRS Mic Output - 1/8“ / 3.5 mm TRS Headphone Output

• Gain - 0-4 Level (0 to 8dB)

• Audio Output Level - Line Out: 1V, Monitoring: 25-30mW

• Power Requirement - 3.3V-4.7V

• Battery Type - Built-in Lithium Battery, 400mAh

• Battery Charging Time - 1.5h

• Battery Life - 5h

• Dimensions - 52X42X16mm

• Material - Plastic

• Weight - 35g

Microphone

• Form Factor - Built-in/External Mic

• Sound Field - Mono

• Polar Pattern - Omnidirectional

• Frequency Response - 50Hz-20KHz

• Sensitivity - -40dB (±3 dB, re 1V/Pa at 1KHz)

• Max. Input SPL - 135dB SPL (at 1KHz)

View fullsize

In this Field Test Shooting Video I perform my usual Chronograph and Accuracy tests in the Replica Airguns Indoor Sea Can Shooting Range to find out what the actual feet per second velocity is and how accurate the ICS CPX-APE SF1 AEG Airsoft Rifle is in both semi auto and full auto. Watch my Table Top Video if you are looking for more info on Specifications and Details along with a full tear down of the ICS CPX-APE SF1 AEG Airsoft Rifle.

First up I place 6 rounds through my Chronograph to see what the real world velocity is and the ICS CPX-APE SF1 AEG Airsoft Rifle was able to average 391 fps using .25 gram plastic Airsoft BB’s. ICS claims the ICS CPX-APE SF1 is capable of fps up to 460 fps but this would be using lighter .20 gram Airsoft BB’s which I believe is entirely possible!

Next I put a fresh paper target on my metal backstop 30 feet downrange and proceeded to shoot 10 round in semi auto to see how tight of a grouping I could get. I was happy to see that 7 of my 10 rounds all grouped nicely within the 1.5 inch bullseye and only 3 came out just slightly increasing the grouping to around 2 inches but still closer to 1.5 inches. When I switched over to full auto and emptied the 300 round magazine into the target, amazingly the grouping still seemed to stay pretty close to 2 inches in diameter with some stragglers. The ICS CPX-APE SF1 AEG Airsoft Rifle punched a satisfying hole in my target going through several layers of cardboard.

As you can see in this YouTube Field Test Shooting Video the ICS CPX-APE SF1 AEG Airsoft Rifle performed very well for me living up to its pristine price point. You will pay top dollar for the ICS CPX-APE SF1 AEG Airsoft Rifle but will also get top quality with a ton fo features including an almost all metal/aluminum build, ambidextrous controls throughout, tons of add on capabilities using the 5 sided Keymod hand-gurd, fully adjustable folding stock and exceptional performance.

• Buy the ICS CPX-APE SF1 AEG Airsoft Rifle in Canada

View fullsize

Type: AEG EBB Airsoft.
Manufacturer: ICS
Model: CPX-APE SF1
Materials: Mostly Metal/Aluminum.
Weight: 6.4 pounds (2900 grams).
Length: 25.2 inches folded / 32.5-36.2 unfolded.
Hop-up: Yes adjustable.
Propulsion: AEG EBB (Electric Blowback).
Action: Semi & Full Auto single action only electric trigger.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 300 rounds.
FPS: 460 fps.

View fullsize

Trigger Pull: The trigger pull on the ICS CPX-APE SF1 AEG Airsoft Rifle is pretty much like most AEG Electric trigger operated Airsoft Rifles. Usually mid range, light and with no real noticeable release point since it is an electric on and on switch at the end of the day and not really mechanical. Of course you can elect between semi and full auto operation at will.

Accuracy: I have not done my actual Field Test Shooting video review for the ICS CPX-APE SF1 AEG Airsoft Rifle but plan to tackle this video next on my list so this week for sure, stay posted of this one as I have not Field Tested any ICS Airsoft Rifles to date and really don’t know what to expect!

View fullsize

Build Quality: The G&G ICS CPX-APE SF1 AEG Airsoft Rifle is extremely well made as the price tag would suggest. You are going to find metal almost everywhere on this product including the all aluminum upper receiver. The only plastic I could find on the ICS CPX-APE SF1 AEG Airsoft Rifle was in the magazine and the folding butt stock. Everything else is metal/aluminum including the upper and lowe receivers, the sights, the rails and all of the controls. Fit and finish feels great as-well!

Realism: The ICS CPX-APE SF1 AEG Airsoft Rifle is not a replica so to speak of any one particular gun in production but does have some AR and perhaps SCAR attributes to it. Perhaps there needs to be a real steel version of this gun as it does combine a bit of the best of a both platforms. The ICS CPX-APE SF1 AEG Airsoft Rifle is sold for sure with great weigth and feel to it being that it is mostly metal. All the controls work exactly like you would expect on a the real powder burner and you can totally take this Airsoft rifle apart in just a minute or two with virtually no tools.

Available in the: Replica Airguns Store

View fullsize

Pros:

• Mostly metal construction with full aluminum upper receiver.

• Tons of rail attachment options with the 5 sided Keymod rail hand-guard.

• Fully adjustable pop-up iron sights.

• Most everything is ambidextrous: Selector switch, Magazine release, Charging handle, Sling mount.

• Rear folding stock has tons of positions, 6 in length and 5 for cheek rest.

• Super easy access to everything, hop-up, gear box, inner barrel, outer barrel.

• Electric blowback system for slight recoil effect.

• T-window in magazine for quick ammunition checks.

• FPS is nice and high, great for longer range shooting.

View fullsize

Cons:

• On the expensive side but very high quality.

• Limited battery options as space for a battery is tight.

• May have a bit too high of fps for closer quarter indoor Airsoft games.

View fullsize

Comments:

The ICS CPX-APE SF1 AEG Airsoft Rifle is not an inexpensive product and may be a bit out of touch for Airsofters on a tighter budget. That said it is really well thought out and well built Airsoft product that is ready to go with no real upgrading required. You may want to show on an optical or red dot sigh, perhaps a tac light or fore grip? Nothing you need right away. There really isn’t one thing I can point out that makes this gun so great, it is a combination of everything. when it comes down to it the ICS CPX-APE SF1 AEG Airsoft Rifle kind of has it all going for it. I am looking forward to seeing just how well it performs during my Indoor Field Test. I have high hopes!

• Buy the ICS CPX-APE SF1 AEG Airsoft Rifle in Canada

I made a video a little bit ago talking about how Canada’s new Bill C-21 will affect pretty every gun owner in Canada including even airgun owners of BB, Pellet Airsoft and even Paintball Guns. Make sure to watch that video first called Bill C-21 Canada is Going After Your Red Ryder BB Gun.

This video is all about how you can get involved in making some waves by signing two online petitions along with contacting your local Member of Parliament and letting them know your disapproval of Bill C-21 and all that it imposes on law abiding Canadian gun owners.

Probably the most important online petition to sign would be the House of Commons Petition E-3201 Bill C-21 so make sure to sign that one!

The other online e-petition we need to sign is the change.org petition.

And lastly but also super important is to send an email to your local member of Parliament again let them know your disapproval of Bill C-21. I have included a link to the web[age where you can locate your local MP and below that is a template of what you could include in your email to them.

https://petitions.ourcommons.ca/en/Petition/Sign/e-3201

Dear (MP),

I am a constituent in your riding. I am writing to you to voice my concerns over the new provisions that were announced under the proposed Bill C-21, and how this will impact myself, my community and many other Canadians.

"Criminal Code 1 (1) The definition replica firearm in subsection 84(1) of the Criminal Code is replaced by the following:

replica firearm means any device that is designed or intended to exactly resemble, or to resemble with near precision, a firearm that is designed or adapted to discharge a shot, bullet or other projectile at a muzzle velocity exceeding 152.4 m per second and at a muzzle energy exceeding 5.7 Joules, and that itself is not a firearm, but does not include any such device that is designed or intended to exactly resemble, or to resemble with near precision, an antique firearm; (réplique)

(2) Section 84 of the Act is amended by adding the following after subsection (3.1): Certain firearms deemed to be prohibited devices

(3.2) For the purposes of sections 99 to 101, 103 to 107 and 117.03, a firearm is deemed to be a prohibited device if

(a) it is proved that the firearm is not designed or adapted to discharge a shot, bullet or other projectile at a muzzle velocity exceeding 152.4 m per second or at a muzzle energy exceeding 5.7 Joules; and (b) the firearm is designed or intended to exactly resemble, or to resemble with near precision, a firearm, other than an antique firearm, that is designed or adapted to discharge a shot, bullet or other projectile at a muzzle velocity exceeding 152.4 m per second and at a muzzle energy exceeding 5.7 Joules."