In this Comparison Video I show several models of Glock Replica Airguns distributed under the Umarex/Glock license. Umarex has brought to market several Glock Replica Airguns to date including BB, Pellet, Airsoft and even Paintball versions in a variety of models. I showcase only a few of these models in this video but it is a good selection to give most people an idea of what is available from our Replica Airguns website in terms of Glock Pistols.
In this Field Test Shooting Video I put the Arcturus AR06 - NY03CB AEG Airsoft Rifles through their paces to find out what the actual Velocity is and how Accurate they both are in both semi and full auto. I use .20 gram Airsoft BB’s for all of the test and I also use an 11.1 volt battery in each Airsoft Rifle. Make sure to checkout my combined Table Top Video for the Arcturus AR06 - NY03CB AEG Airsoft Rifles for more details and info.
Starting off with the velocity or fps for the Arcturus AR06 - NY03CB AEG Airsoft Rifles I place 4-5 rounds through my Chronograph and average the shots out to see what the fps is. Arcturus claims around 380-400 fps but I actually got a bit hotter velocities from both guns with the AR06 averaging 401 fps and the NY03CB averaging 412 fps. Both where supper consistent with their fps, about 2-3fps between the highest and lowest shots.
For my Accuracy Test I shot both the Arcturus AR06 - NY03CB AEG Airsoft Rifles in semi auto first using 10 rounds to find out what the groupings looked like at 30 feet away. I then switch both AEG Airsoft Guns over to full auto and dumped a spring load full form the high-cappa magazine into the paper target setup again at 30 feet down range to see if the groupings opened up much more. The Arcturus AR06 did place all 10 rounds right in about a 1 inch grouping just a tad low and ever so slightly to the left of the bullseye, while the Arcturus NY03CB again got close to the 1 inch grouping but had a few outliers that spread it out to closer to 2 inches, it may hav been me as human factor is for sure a possibility. The Arcturus NY03CB did shoot a little bit closer to the bullseye out of the box but both of these Arcturus AEG Airsoft Rifles have fully adjustable sights. When it came to full auto, both rifles groupings opened up a bit, but not much as the recoil on these AEG rifles is not really a factor.
As I mention in this video, there is a rather large price difference of around $200 extra for the Arcturus AR06 which does get you more metal and some upgrades internally but in the end they both performed about the same, so either choice would be good. I personally like the all metal and look of the Arcturus AR06 but if you want a similar performing AEG and save some money then grab the Arcturus NY03CB.
It took me a bit to get to this Field Test Reviews done for both the Arcturus AK05 AK AEG and Arcturus AK06 AK AEG Airsoft Rifles but I finally made them! if you want more specifications and details along with closeup video of the Arcturus AK05 then make sure to checkout my Table Tope Review Video for it. In this video I will be testing out the Velocity and then move on to the Accuracy for this AEG Airsoft Rifle in both semi and full auto conducted in the Replica Airguns Sea Can Indoor Airgun Range.
First I placed 5 rounds through my Chronograph shooting .20 gram Airsoft BB’s and I found the Arcturus AK05 AK AEG Airsoft Rifle to be on the higher fps range and it was very consistent with the fastest shot hitting 401 fps and the slowest shot hitting 393. This average an impressive 398 fps which could be a bit hot for some Airsoft Game shooting situations, but perhaps ideal when shooting outdoors at longer ranges.
I then placed a fresh paper target up 30 feet down range and proceeded to shot 10 rounds into the target using a seated and rested shooting position. I followed this up with a spring full of BB’s in full auto in semi auto and full auto getting a bit tighter group in semi auto then I did in full auto but this is generally the case. I did have a bit of trouble with the magazine not loading Airsoft BB’s even though I did tighten the spring fully between testing. Perhaps the magazine needed some break in time or was even defective? Out of the box the Arcturus AK05 AK AEG Airsoft Rifle shot very close to the bullseye but just a tad to the left but not by much. The sights are adjustable for elevation if need be, or you can put a compact red dot sight on the rail for spot on accuracy.
I really did like the Arcturus AK05 AK AEG Airsoft Rifle as it performed very well for me in terms of both power and accuracy other then the magazine acting up. I would most likely add a compact red dot sight on the rail as the built in sights are limited in terms of windage adjustments. You can also see in this video that I had to take off the top dust receiver cover in order to place the battery in it, you will need a very specific and compact battery in order to have it installed and be able to close the top cover. Those two things aside the Arcturus AK05 AK AEG Airsoft Rifle is a great choice if you are looking for a compact and more modernized AK type AEG Airsoft Rifle. Also make sure to watch my Arcturus AK05 AK AEG Airsoft Rifle Field Test Review already available to view on Vimeo!
It took me a bit to get to this Field Test Review for the Arcturus AK06 AK AEG Airsoft Rifle but here we are, if you want more specifications and details along with closeup video of the Arcturus AK06 then make sure to checkout my Table Tope Review Video for it. In this video I will be testing out the Velocity and accuracy in both semi and full auto here in the Replica Airguns Sea Can Indoor Airgun Range.
First off I placed 5 rounds through my Chronograph shooting .20 gram Airsoft BB’s and I found the Arcturus AK06 AK AEG Airsoft Rifle to be very consistent with the fastest shot hitting 370 fps and the slowest shot hitting 368, this average an impressive 369 fps which is perfect for most Airsoft Gam shooting situations.
I then placed a fresh paper target up 30 feet down range and proceeded to shot 10 rounds into the target using a seated and rested shooting position. I followed this up with a spring full of shots in full auto with semi auto and full auto getting pretty much the exact same results which I would say to be about a 1.5-2 inch grouping. Out of the box the Arcturus AK06 AK AEG Airsoft Rifle did shot a bit high making me aim about 6 inches lower to achieve hits in the bullseye. Perhaps hope could remedy this as the sights are too adjustable…
I really did like the Arcturus AK06 AK AEG Airsoft Rifle as it performed very well for me in terms of both power and accuracy. I was not a fan of the built in sights as the notch in the back was so low that it barely lined up allowed for it to be inline with the front post sight, I kind of had to guess where the notch was to make it work. I would for sure put a red dot on the rail as the built in sights are pretty much useless. you can also see in this video that I had to take off the top dust receiver cover in order to place my battery in it, you will need a very specific battery in order to have it installed and close the top cover. those two things aside the Arcturus AK06 AK AEG Airsoft Rifle is a really great AK Staled AEG Airsoft Rifle in my books stay tuned for my Arcturus AK05 AK AEG Airsoft Rifle Field Test Review coming soon!
I First off this Field Test Shooting Video Review for the Umarex HK P30 AEG Full Auto Airsoft Pistol is going to be more like reviewing a NERF gun, well at least in terms of performance. I do however test it out just like I test all Airsoft Pistols by shooting 5 rounds through the Chronograph to see what the average velocity is in fps. Then I shoot some rounds at a paper target setup 30 feet downrange to see how accurate the Umarex HK P30 AEG Full Auto Airsoft Pistol is. If you want more specification and details along with some nice close up video of the Umarex HK P30, then checkout my Table Top Video for it.
OK, so starting with velocity, I have to say it shot well below the claimed 180fps on the clamshell packaging, keep in mind this is for .12 gram Airsoft BB’s and I was using .20 gram Airsoft BB’s so almost twice as heavy which should mean about half the speed and that’s about what I got. I was able to get an average fps of 95 with my slowest shot hitting 94 fps and my fastest shot hitting 96 fps so very consistently slow :)
What about accuracy? Could the mighty Umarex HK P30 AEG Full Auto Airsoft Pistol at least redeem itself here… Well not really! It was hard to fully determine exactly where my shots where hitting the paper target as it seems 95 fps is not powerful enough to even penetrate the paper. All I could do was put little dings in the paper which are bit hard to make out. My best guess is I should be able to hit a standard sheet of paper at 30 feet away once I figure out where the center point is. I was shooting at the bullseye and hit most shots rather low on the target with several of them being too low to get on the paper. In full auto things did not get much better, but full auto with this little pea shooter is kind of fun, so just keep the selector on full auto all the time… I would!
Getting back to the Umarex HK P30 AEG Full Auto Airsoft Pistol being more like a NERF gun, I say this because it is way too underpowered to use in any Airsoft wars as people probably won’t even know they got hit! But perhaps it is just perfect for indoor NERF type shootouts? I can’t see the Umarex HK P30 doing any type of damage to your surroundings or to yourself but always make sure to wear eye protection when shooting as even an eye lash can feel like murder in the eye let alone a 6mm Airsoft BB. The only real downside I can see to using the Umarex HK P30 AEG Full Auto Airsoft Pistol indoors like a NERF gun would be the cleanup of all the microscopic Airsoft BB’s, you will probably be finding them under furniture and in crazy spots for months afterwards. All in all, the Umarex HK P30 AEG Full Auto Airsoft Pistol may just be perfect for some indoor fun on those rainy days!
The KJ Works KP-13 CO2 Blowback Airsoft Pistol does look a bit like a Glock but don’t be fooled, it is fore sure not a Glock at all. That said it might just make a great training Airsoft pistol if you own a real steel Glock or plan on owning one in the future as it is about the same size and shape and operates similarly to a real Glock. In this video I put it through its paces using my Chronograph to find out the real world velocity and I also place 10 shots on a paper target to see what kind of accuracy I can get from 30 feet away.
Starting with my power or velocity test I put 5 rounds through my Chronograph using standard .20 gram Airsoft Plastic BB’s. I was using a brand new CO2 and the temperature being around 21 degrees Celsius or 70 degrees Fahrenheit, so not too hot or cold. I did only test using the preinstalled internal non-extended barrel so if you do plan on using the longer extend barrel that the KJ Works KP-13 CO2 Blowback Airsoft Pistol comes with, you will more than likely get another 30-40 fps out of this Airsoft Pistol. That said I was able to get an average of 348 fps with my slowest shoot hitting 329 fps and my fastest shot hitting 363 fps. As expected the fastest shot was my first shot out of the Airsoft gun and my slowest shot was my last as the Airgun cooled down.
I then moved on to my accuracy portion of the Field Test for the KJ Works KP-13 CO2 Blowback Airsoft Pistol. It did shoot rather high so I did have to aim at the bottom ring of the target to actually hit closer to the middle. It also shot just a tad to the left but not much so keep that in mind since the sights are not easily adjustable. Hop-up adjustments may lower the rounds a bit but it’s hard to say how much. The KJ Works KP-13 CO2 Blowback Airsoft Pistol did get close to a 1 inch 9 shot grouping (first shot was really high aiming at the bullseye), so that was impressive and the blowback feels solid with a really nice Glock like short and easy trigger.
The KJ Works KP-13 CO2 Blowback Airsoft Pistol is a nice looking and good performing Airsoft Pistol that looks enough like a glock to perhaps appeal to Glock lovers looking for something similar but unique in its own way. After all doesn't everyone already have a Glock, so be a bit different and pick yourself up one of these KJ Works KP-13 CO2 Blowback Airsoft Pistols and be a trend setter!
The Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol is a looker for sure replicating the look of a Glock 17 Gen 5 which includes Umarex Glock licensing, lots of metal parts and solid blowback action. That’s all great but does it shoot good? In this Filed Test Shooting video for the Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol I put it through its paces using my Chronograph to find out the real world velocity and I also place 10 shots on a paper target to see what kind of accuracy we can get from 30 feet away.
Starting with my power or velocity test I put 5 rounds through my Chronograph using lead pellets that where just over 7 gran. I was all using a brand new CO2 and the temperature being around 21 degrees Celsius or 70 degrees Fahrenheit, so not too hot or cold. Full disclaimer, I was having some feeding problems with the magazine at first but it did seem to sort itself out near the end of this review… All that said, I was able to get an average of 320 fps with my slowest shoot hitting 309 fps and my fastest shot hitting 327 fps, so pretty consistent overall.
I then moved on to my accuracy portion of the Field Test for the Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol Luckily the pellet feeding and trigger seemed to work better for me during this portion of the test but the trigger pull was very unpredictable being super hard with some shots and rather easy for others. This is not ideal for getting a good accuracy result, but I did the best I could and surprisingly got around a 3 inch grouping with a very uncooperative trigger. My grouping did hit the target a little bit to the left but was well centered up and down.
I am not a fan of belt fed magazines over all even though Sig Sauer does seem to be able to pull them off better than anyone. Maybe Umarex needs to do a little bit more work here to get better trigger pull consistency and an overall lighter trigger pull. Maybe the Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol needs a bit more break in time as it did seem to perform better near the end of my Field Test Review. I would also like to try adding some silicone lubrication ot the magazine as friction seems to be the enemy of belt fed magazines… I am not sure if the Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol is a big recommendation for me or not, but it is a really decent CO2 Airgun in many ways. If you're willing to take a bit of a chance that the trigger will improve over time and perhaps a bit of lube will improve things then checkout the Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol in our Canada and US online Replica Airguns Stores.
Type: Blowback CO2 Airsoft Pistol. Manufacturer: Distributed by KJ Works. Model:KP-13. Materials: Metal & Polymer. Weight: 1.7 pounds (770 grams). Barrel: 3.7 inches (95mm) metal non-rifled. Propulsion: CO2 x 1. Action: Semi auto blowback, SOA trigger. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: 24 round drop out full size metal magazine. FPS: Claimed 366+.
Trigger Pull: The trigger pull on the KJ Works KP-13 CO2 Blowback Airsoft Pistol is what you would expect for a true Single Action Only Trigger which is nice and light. There is a bit of take up but you can feel the point near the back where the release kicks in which is extremely predictable with no play in it. Of course you will need to rack the slide in order to place a round in the breach and fire the first shot, after that the blowback action will do all the work for you.
Accuracy: At this point I have not shot the KJWorks KP-13 CO2 Blowback Airsoft Pistol or done my Field Test Performance Video. I would expect the KJWorks KP-13 to perform like the other KJWork Airsoft Pistols I have reviewed in the past, which generally hits the claimed fps. Keep in mind the claimed fps is with the extended barrel and I more than likely will be using the preinstalled shorter non extendable barrel which will have a slower fps for sure. Accuracy should be decent but we will find out when I make my Field Test Shooting video!
Build Quality: The KJWorks line of Airsoft Guns is know for overall good quality so I expect theKJ Works KP-13 CO2 Blowback Airsoft Pistol to be just the same. From my initial first impressions everything looks really good, fit and finish are excellent and as expected you will find metal parts and polymer parts in all the same places you would find them in a real steel modern semi auto pistol.
Realism: The KJ Works KP-13 CO2 Blowback Airsoft Pistol is not an exact replica of a specific semi auto pistol but yo could say it looks a little bit like a Glock ;) You need to be careful when it comes to Glock as they do not like it when companies copy their guns and rightly so. There is enough differences with the KJ Works KP-13 CO2 Blowback Airsoft Pistol so it should not set off any alarms over at Glock. I do like the two tone tan and black color scheme KJ Works went with for the KP-13 but if you like a more traditional look you can always go with the all black version.
Pros:
Metal and Polymer with decent weight and good feel to it.
Heavy Full blowback operation.
Excellent fit and finish as always with KJWorks pistols.
High capacity full size drop out metal magazine that holds the CO2 and 24 rounds.
Well hidden safety incorporated into the serial number under the barrel.
Working trigger safety.
Super easy to see in all conditions fiber optic sight up front.
All working components like a real steel Glock styled pistol.
Comes with extended barrel for higher velocity and easier import into Canada.
Would make a good training weapon if you are use to using Glocks.
Like the two tone finish, but can also get it in all black.
Easily field strip-able.
Cons:
Sights are not adjustable.
Would have liked the addition of white outline on the rear sight.
Slide spring could be slightly heavier.
Comments:
If you’re looking for a pistol that is similar to a Glock for training purposes but is unique in its own way and doesn’t have to be a Glock, then perhaps the KJ Works KP-13 CO2 Blowback Airsoft Pistol may be for you. I like the fact that it has its own style to it and is not just another Glock or Glock Copy. I also like that the KP-13 comes with a CO2 magazine rather than a Green Gas Magazine which will get you a bit higher velocity and more mag fills before requiring to gas up again. I personally like the two tone version but get what you like best, it’s good to have options!
Type: Blowback CO2 Pellet Pistol. Manufacturer: Distributed by Umarex. Model:Glock 17 Gen 5. Materials: Metal & Polymer. Weight: 1.6 pounds (725 grams). Barrel: 4.5 inches metal non-rifled. Propulsion: CO2 x 1. Action: Semi auto blowback, DOA trigger. Ammunition Type: .177 caliber pellets. Ammunition Capacity: 21 round drop out full size metal magazine. FPS: Claimed 370.
Trigger Pull: The trigger pull on the Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol is what I would describe as closer to a DOA (Double Action Only) trigger. The blowback action does retract the internal hammer/striker which does relieve some of the trigger pull but the trigger is also used to rotate the belt magazine which gives the trigger a kind of friction feel especially right at the end of the pull where the rotation occurs. That said it is not a terrible trigger like some other belt fed Airguns but it is certainly nutlike a standard SAO type Glock trigger.
Accuracy: At this point I have not shot the Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol so I can only quote what Umarex is saying in terms of FP2 which is 370. That sounds a bit high for a pellet Airgun but they may be claiming this velocity using a light weight pellets perhaps made out of an alloy rather than lead? I guess we will find out the real world fps using lead pellets and also how accurate it will be when I do my Full Field Test Shooting Video.
Build Quality: The Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol like most of the Umarex Glocks is very well made. I am thinking that Glock to allow Umarex to license Glock Pistols hammy have a quality control as part of this license agreement? Either way the Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol is a solid and well built Airgun all around with quality material and very good fit and finish.
Realism: The Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol in terms of realism as compared to a real steel Glock 19 Gen 5 for sure hits the mark in most categories. It is a bit lighter and you can not field strip it easily, there is also the not so much recessed barrel that is a bit of a giveaway but in terms of most other attributes the Umarex Glock 17 Gen 5 replicates a real Glock… Including the basic looks and feel, the metal slide and polymer frame, the full size drop out metal magazine, the blowback action and most of the working parts including the slide catch release, magazine release and trigger safety.
Pros:
Good weight and feel to it, build quality and fit and finish seem very good.
Really nice looking and full featured replica of the original Glock 17 Gen 5.
Fully Glock licensed via Umarex.
Easy to see white dot sights front and back.
Working trigger safety.
Accessory rail for adding a laser or tactical light.
Full size drop out metal magazine that holds the CO2 and .177 caliber pellets.
Nice high 21 round capacity.
Slide spring feels nice and heavy provide a decent blowback recoil effect.
Safety built into the serial number plate area keeps it well hidden.
Can see through ejection port when magazine is out.
Warning instruction are nice and discreet under trigger guard.
370 claimed fps is good for a CO2 blowback pellet pistol.
Cons:
Barrel is not really all that recessed.
No way to easily field strip it.
Don’t like the clam shell packaging.
Trigger is a bit on the heavy side.
Comments:
I think many of us having been waiting for a pellet shooting version of the Glock from Umarex. I am a bit surprised they went with a belt fed version as belt fed magazines tend to be a bit on the heavy trigger pull side. Yes the Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol has a stronger trigger pull as compared to a 4.5mm BB or 6mm Airsoft version of the same Umarex gun, as most of these Umarex based Glocks utilize a SAO trigger which is more comparable to a real steel Glock. On the plus side the Pellet version should be a bit more accurate, but we will see how this pans out when I do my comprehensive Field Test Shooting Video for the Umarex Glock 17 Gen 5 CO2 Blowback Pellet Pistol.
Type: BB air pistol. Manufacturer: Umarex USA. Model: HK P30 Materials: All pastic outer shell. Weight: .5 pounds (227 grams) Barrel: Metal non-rifled 4.25 inches (106mm). Total Length: 7 inches (178mm) Propulsion: CO2 x 1. Action: Semi & full auto blowback, single action only. Ammunition Type: 6mm Plastic Airsoft BB's. Ammunition Capacity: 16 round plastic curved stick magazine x2. FPS: 180 Rate of fire: 200 shots/min.
Trigger Pull: The trigger on the Umarex HK P30 AEG Full Auto Airsoft Pistol is electric as it is an AEG Pistol that requires batteries to operate. The trigger is basically an ON/Off switch that activates the blowback which also seems to create the pressure to propel an Airsoft BB. Mind you not all that fast but fast enough for perhaps a more safe indoor/basement type Airsoft war? Getting back to the trigger pull I would say it is light but on the ing side for an AEG.
Accuracy: You will have to stay posted for my proper Field Test Shooting Video for the Umarex HK P30 AEG Full Auto Airsoft Pistol. That said I did pop off a magazine of BB’s (16 rounds), some in semi auto and some in full auto. Do not expect this Airsoft pistol to be all that powerful as it can barely penetrate a paper target. I was expecting the cycle rate of full auto to feel slower than it actually shot so that’s a good thing! I see this as almost an alternative to a nerf gun but using Airsoft BB’s. Do this at your own risk and please use proper eye protection. I can not comment too much on accuracy as I was just pointing and shooting to get a basic feel for the gun.
Build Quality: The Umarex HK P30 AEG Full Auto Airsoft Pistol is a low cost all plastic Airsoft pistol which kind of says it all. Being super light weight means if you drop it, chances are it will be fine because it is so light weight. Fit and finish are decent but without seeing what’s inside I can only guess at how long it will last.
Realism: The Umarex HK P30 AEG Full Auto Airsoft Pistol is a true licensed replica via Umarex. It is about the right shape and size as a real HK P30 and other than the orange tip could fool most people unless really close up to it and of course holding it. It also has a kind of out of place grip safety on the front which is not an HK attribute. Being an AEG with batteries in the grip there is no full size magazine and again as it is all plastic it does not have nearly the same weight as a real HK P30. The only working mechanical parts are essentially the trigger, grip safety and selector switch in the trigger area.
Available From: The Canada and US Replica Airgun Stores.
Pros:
Drop out stick mags are nice for continuous shooting without having to reload as often.
Has a rail for accessories.
Working slide with blowback action.
Shoots in both semi and full auto selectable.
No CO2 so perhaps better in colder weather being an AEG, lower cost to operate!
Walther licensing via Umarex.
Grip safety to help stop unwanted accidental shots.
Serial number on receiver.
Warning instructions are non-obtrusive.
Trigger is nice and light being an AEG.
Cons:
Is very light weight being almost all plastic.
Low claimed fps and slow full auto cycle rate.
Orange tip.
Sights are all black, harder to see on dark objects
Comments:
The Umarex HK P30 AEG Full Auto Airsoft Pistol is a rather different sort of beast! On one hand it is not what you would expect to see someone using in an Airsoft game but I really don’t think that’s what it is meant for anyway. It’s really just a fun gun for plinking without having to worry to much about safety as if you do something stupid, the consequences will not be too sever! I would say it could possibly be used as an alternate to using a Nerf gun for fun little backyard squishes or shooting indoors. The Umarex HK P30 AEG Full Auto Airsoft Pistol is not for everyone but I am guessing it could be a lot of fun when used in the right situations.
Watch my Table Top Video Review for the Umarex HK P30 AEG Full Auto Airsoft Pistol:
Type:Airsoft Rifle. Manufacturer: Acturus. Model: AR06 & NY03CB. Materials: Mostly all Metal. Weight: 5.6/4.9 pounds (2.5/2.2 kilograms). Length: 27.4-30.7/31.7-35 inches (695-780/805-890mm) Barrel Length: 11/14.6 inch (280/370mm) inner 6.02mm tight bore non rifled. Propulsion: AEG (with Deans Connectors). Action: Semi & Full Auto SAO. Ammunition Type: 6mm Airsoft BB's. Ammunition Capacity: Hi Cap/Mid Cap - 550/135 FPS: 380-400fps.
Trigger Pull: The trigger pull on the Arcturus AR06 - NY03CB AEG Airsoft Rifles like other AEG Rifles is not mechanical as they are essentially electrical driven so basically the trigger is an on/off switch that is closest in feel to a single action only trigger since it is light and short. You will notice a slight delay between pressing the trigger and the actual round being fired since the trigger activates a motor which first pulls the air spring back. Once the spring is fully drawn back it releases and compresses the air which then propelled the 6mm Airsoft BB. The higher voltage battery you use like an 11.1 volt will shorten the delay as the motor will spin faster and pull back the spring quicker allowing for less noticeable delay and also a higher rate of full auto fire which in this rifle is very noticeable.
Accuracy: I have not Field Test Reviewed either the Arcturus AR06 - NY03CB AEG Airsoft Rifles or even tried them out yet. I hope to get to my Field Test Shooting Video for both of them later next week, until then we can assume they will shoot similar to most other AEG rifles with tighter bore barrels. I am expecting at least a 2 inch grouping at 30 feet down range in semi auto. In terms of velocity the test paper which they come with claims around 390+fps.
Build Quality: The Arcturus AR06 is a mostly metal with a full metal receiver while the NY03CB has a polymer or plastic receiver which from what I can tell only other components being plastic would be the pistol grips and rear stock. other metal parts on both AR type Airsoft Rifles would be the rail setup, the barrel, the charging handle, the buffer tube, the dust cover, the trigger, the selector switch, the magazine release and bolt release. Fit and finish for both guns is very good.
Realism: The Arcturus AR06 - NY03CB AEG Airsoft Rifles are based on the AR platform with both versions looking the part of a real steel AR. They do come with the removable orange tips installed but they also come with black flash hiders so you can easily switch them out adding to the realism. The metal receiver on the AR06 does give it a bit more weight but even the NY03CB has a decent weight and solid feel to it. Most of the controls work just like a real steel AR including the charging handle, bolt release, selector switch and magazine release.
Pros:
Two versions to meat your budget, both great options.
Quality components throughout both versions. Only real difference is nylon fiber receiver vs metal receiver and slight upgrade motor on AR06 version from Long Type to Long Type 19k torque motor on AR06.
Have been quality control inspected including 5 round recorded fps test with .20 gram Airsoft BB’s.
Both have a functioning bolt catch.
Both come with Quick release two position fully adjustable pop-up sights.
Both come with additional black flash hiders.
Lots of rial mounting options in Picatinny and M-LOK.
6 position adjustable rear stocks.
Easy access to motor for any possible trouble shooting you may need to do.
Additional grip plate option.
Ambidextrous controls and ambidextrous sling mounting points (QD on AR06).
Two magazines come with AR06 (Mid Cap and High Cap).
Cons:
Limited battery options as area is small.
Kind of need a tool to remove rear stock for battery access. (Could change the rear stock)
Mystery accessory baffles me and not mentioned in the manual.
Comments:
Like the AK series of Acturus AEG Airpot Rifles, the Arcturus AR06 - NY03CB AEG are good value for the money with the AR06 offering a slightly higher premium over the lower cost NY03CB. But don’t let the lower price fool you into thinking you are getting a sub-standard product as both versions are built with many of the same components. I personally like the more compact look of the Arcturus AR06 AEG Airsoft Rifle but then again the price of the NY03CB AEG Airsoft Rifle is hard to ignore. Either way you can’t go too wrong so make your pick and enjoy owning one of them.
My Table Top Video of the Acturus AR06 - NY03CB AR AEG Airsoft Rifles:
Yet another Field Test Shooting Video performed in the Replica Airguns Indoor Airgun Sea Can Shooting Range! In this Field Test I shoot the Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol to see what kind of velocity and accuracy it has shooting .20 gram Airsoft BB’s with a brand new CO2 cartridge. If you are interested in the specifications and details along with some more close up video than watch my Table Top Review Video here.
Like pretty much every Field Test Shooting video I first perform the Chronograph Velocity Test since my CO2 is the most fresh at this point. I didn’t check the temperature in the Sea Can but I generally keep it around 20-22 degrees Celsius which is 68-72 Fahrenheit. I was a bit amazed at the high velocity of the Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol in my testing as the claimed fps was 410 and most guns don’t live up to their claims exactly. The Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol shooting 5 shots through the Chronograph averaged 431 fps with the slowest shot at 427fps and the fastest shot hitting 439fps so consistency was good!
Next I setup a fresh paper target 30 feet downrange and proceeded to place 10 rounds in it using a rested shooting position with my hands resting on a sandbag up front and seated in the back. Watch the video to see what actually happened but in a nut shell the Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol shoots really high at 30 feet, at least 10 inches. So I did need to figure out where it was shooting before I actually got rounds on the paper. It was a bit hard to figure out the precise 10 shot grouping since some rounds may have even shot over the target when I was aiming at the bottom of the target but my best estimate is around 3-4 inches.
Other than the rather high shot placement which may be adjustable to some degree by adjusting the hop-up,I would say the Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol is a very nice gun. The power is really good and may even be a bit much for close quarters indoor games but outdoors where you are shooting longer ranges it should perform well in these conditions. The blowback is very strong and the trigger feels good. If you don’t mind adjusting your shooting point a bit then the Umarex S&W M&P 9L Blowback CO2 Airsoft Pistol would be a great choice as your sidearm.
In this Preview Review Video I take a look at 4 newer products now in our Replica Airguns Online Store. One is a 4.5mm Steel BB Revolver, two are 6mm Airsoft Pistols and one is a .68 caliber Paintball Shotgun.
The first item I take look at in this video is the Umarex HK30 AEG Airsoft Pistol, this product is pretty entry level with analyst all plastic build and is very light to hold. It does however shoot in both semi and full auto since it is an AEG Airsfto Pistol (not many of them out there). The fps is rather low at a claimed fps at just under 200, the Umarex HK30 AEG Airsoft Pistol also comes with two 16 round remove; plastic magazines. Who knows, maybe it will be fun?
Next I take a look at the ASG Dan Wesson 2.5 inch 4.5mm Steel BB Gold Revolver. This is a CO2 powered shell loading BB revolver very much like similar ones I have reviewed in the past but in Gold finish. Will the gold finishes make it perform better, well I guess we better find out!
I then take a look at a “Glock Like” CO2 Blowback Airsoft Pistol for KJWorks called the KP13. It has a full size drop out metal magazine that holds the CO2 along with 24 rounds of 6mm Airsoft BB’s. The KJWorks KP-13 has a metal slide, metal magazine and polymer frame with a velocity over 360fps using the included barrel extension.
Last but perhaps the most interesting for me is the Umarex T4E HDB which is a lower cost Paintball/Rubber Ball Shotgun which could possibly be used for home protection? The T4E HDB is a mostly plastic constructed rifle with decent weight to it and uses an internal spring fed 16 round magazine. You will find all kinds of mounting points for accessories and for a sling on the Umarex T4E HDB and again at much lower cost than similar T4E rifle based Paintball/Rubber ball Airguns.
Type:Airsoft Rifle. Manufacturer: Acturus. Model: AK05. Materials: Mostly all Metal. Weight: 8.2 pounds (3.7 kilograms). Length: 31.1 inches (790mm) Barrel Length: 11 inch (280mm) inner 6.02mm tight bore non rifled. Propulsion: AEG (with Deans Connectors). Action: Semi & Full Auto SAO. Ammunition Type: 6mm Airsoft BB's. Ammunition Capacity: Hi Cap/Mid Cap - 550/135 FPS: 380-400fps.
Trigger Pull: The trigger pull on the Acturus AK05 AK AEG Airsoft Rifle like other AEG Rifles is not mechanical as it is essentially electrical driven so basically it is an on/off switch that is closest in feel to a single action only trigger since it is light and short. You will notice a slight delay between pressing the trigger and the actual round being fired since the trigger activates a motor which first pulls the air spring back. Once the spring is fully drawn back it releases and compresses the air which then propelled the 6mm Airsoft BB. The higher voltage battery you use like an 11.1 volt will shorten the delay as the motor will spin faster and pull back the spring quicker allowing for less noticeable delay and also a higher rate of full auto fire which in this rifle is very noticeable.
Accuracy: I have not Field Test Reviewed the Acturus AK05 AK AEG Airsoft Rifle or even tried it out yet. I hope to get to my Field Test Shooting Video for the AK05 later next week, until then we can assume it will shoot similar to most other AEG rifles with tighter bore barrels. I am expecting at least a 2 inch grouping at 30 feet down range in semi auto. In terms of velocity the test paper work it comes with claims around 390+fps.
Build Quality: The Acturus AK05 AK AEG Airsoft Rifle is almost all metal in design with from what I can tell only the pistol grip being plastic. The receiver and top dust cover are both hardened steel with the receiver made out of stamped steel just like areal AK. The AK05 is nice and heavy for its size and the fit and finishes is very good all around. Internal parts are all of high quality too.
Realism: The Acturus AK05 AK AEG Airsoft Rifle is based on the AK platform with this version being a more compact and tactical model. Externally it looks the part for sure, holding it in your hands it feels the part too. As expected the insides are all Airsoft but you would need ot take the dust cover off or pull back the charging handle to figure this out. Again the Acturus AK05 AK AEG Airsoft Rifle is an almost all metal Airsoft Gun with an actual stamped steel receiver and steel dust cover, it’s hard to get much more realistic looking and feeling than that.
Pros:
Lots of mounting options: Picatinny rails, M-LOK, AK Side Rail.
Semi and full auto adjustable.
5 position adjustable rear stock.
Mostly metal construction and lots of actual steel including the receiver and dust cover.
Lots of weight to it at 8.2 pounds, feels awesome to hold.
Comes with two magazines, one Hi Cap and one Mid Cap.
Comes with a secondary all black squared off flash hider.
On the fly adjustable rear sight for elevation.
Quick change spring system.
Easy to get to and adjust rotary hop-up adjustment.
Should be good for longer range shooting with nice high claimed fps.
Cons:
Will need a very specific battery type, thin and long.
Rear sight only adjustable for windage and not elevation.
May even be a bit heavy for all day use.
Comments:
The Acturus AK05 AK AEG Airsoft Rifle along with the other Acturus AK Airsoft Rifles is in my opinion one of the nicest AEG AK based Airsoft rifles you can get, at least in the mid price ranges. Being all metal with actual stamped steel parts really makes the AK05 feel realistic and of high quality. If you’re looking for something with a bit more heft than the Acturus AK06 that has a more useful rear stock at least in terms of adjustability and don’t mind giving up some of the compact features of the AK06 then perhaps the AK05 is more for you. IN my opinion the Acturus AK05 AK AEG Airsoft Rifle is a great combination of quality, size and features, hopefully my upcoming Field Test Shooting Review backs up the performance aspect and we can add that to the list.
My Table Top Video of the Acturus AK05 AK AEG Airsoft Rifle:
Type:Airsoft Rifle. Manufacturer: Acturus. Model: AK06. Materials: Mostly all Metal. Weight: 6 pounds (2.7 kilograms). Length: Folded/unfolded 18.9/27.4 inches (480/695mm) Barrel Length: 9.8 inch (250mm) inner 6.02mm tight bore non rifled. Propulsion: AEG (with Deans Connectors). Action: Semi & Full Auto SAO. Ammunition Type: 6mm Airsoft BB's. Ammunition Capacity: Hi Cap/Mid Cap - 550/135 FPS: 380-400fps.
Trigger Pull: The trigger pull on the Acturus AK06 AK AEG Airsoft Rifle like other AEG Rifles is not mechanical as it is essentially electrical driven so basically it is an on/off switch that is closest in feel to a single action only trigger since it is light and short. You will notice a slight delay between pressing the trigger and the actual round being fired since the trigger activates a motor which first pulls the air spring back. Once the spring is fully drawn back it releases and compresses the air which then propelled the 6mm Airsoft BB. The higher voltage battery you use like an 11.1 volt will shorten the delay as the motor will spin faster and pull back the spring quicker allowing for less noticeable delay and also a higher rate of full auto fire which in this rifle is very noticeable.
Accuracy: I have not Field Test Reviewed the Acturus AK06 AK AEG Airsoft Rifle or even tried it out yet. I hope to get to my Field Test Shooting Video for the AK06 later next week, until then we can assume it will shoot similar to most other AEG rifles with tighter bore barrels. I am expecting at least a 2 inch grouping at 30 feet down range in semi auto. In terms of velocity the test paper work it comes with claims around 370fps.
Build Quality: The Acturus AK06 AK AEG Airsoft Rifle is almost all metal in design with from what I can tell only the pistol grip being plastic. The receiver and top dust cover are both hardened steel with the receiver made out of stamped steel just like areal AK. The AK06 is nice and heavy for its size and the fit and finishes is very good all around. Internal parts are all of high quality too.
Realism: The Acturus AK06 AK AEG Airsoft Rifle is based on the AK platform with this version being a more compact and tactical model. Externally it looks the part for sure, holding it in your hands it feels the part too. As expected the insides are all Airsoft but you would need ot take the dust cover off or pull back the charging handle to figure this out. Again the Acturus AK06 AK AEG Airsoft Rifle is an almost all metal Airsoft Gun with an actual stamped steel receiver and steel dust cover, it’s hard to get much more realistic looking and feeling than that.
Pros:
Lots of mounting options: Picatinny rails, M-LOK, AK/SVD Side Rail.
Semi and full auto selectable.
All metal folding rear stock.
Mostly metal construction and lots of actual steel including the receiver and dust cover.
Lots of weight to it at 6 pounds, feels awesome to hold.
Comes with two magazines, one Hi Cap and one Mid Cap.
Comes with a secondary all black squared off flash hider.
Super compact design.
Quick change spring system.
Easy to get to and adjust rotary hop-up adjustment.
Should be good for longer range shooting with nice high claimed fps.
Cons:
Will need a very specific battery type, thin and long.
Sights are non adjustable.
Folding type rear stock not adjustable for pull length.
Comments:
The Acturus AK06 AK AEG Airsoft Rifle along with the other Acturus AK Airsoft Rifles is in my opinion one of the nicest AEG AK based Airsoft rifles you can get, at least in the mid price ranges. Being all metal with actual stamped steel parts really makes the AK06 feel realistic and of high quality. I also like the compact tactical features of the Acturus AK06 AK AEG Airsoft Rifle making it easy to put in a backpack but not too heavy to lug around all day long. The Acturus AK06 AK AEG Airsoft Rifle also has a decent velocity and fairly fast rate of fire especially when using a higher voltage battery so you can expect excellent performance even from such a small compact AEG Airsoft Rifle.
My Table Top Video of the Acturus AK06 AK AEG Airsoft Rifle:
In this Preview Unboxing Video I Take a look at 4 new Airsoft products from Arcturus all of them being AEG Airsoft Rifles with two based on the AK platform and the other two based on the AR platform. Three of the AEG Airsoft Rifles are mostly metal while I also feature a lower cost version with a Nylon Fiber Polymer receiver. All of these Replica AEG Airsoft Rifles are very good quality but you will get all metal (mostly steel and aluminum) build and a Hi-Cap and Mid-Cap magazine with the higher cost versions.
In this Field Test Shooting Video I give the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol my usual Indoor Sea Can shooting field test using my Chronograph to see what the average 5 shot velocity is with .20 gram plastic Airsoft BB’s. I then shoot 10 rounds in semi auto at a paper target setup 30 feet down range using a seated shooting position with my hands rested on a sand bag up front for stability to find out what the accuracy is in semi auto mode. I follow this up with a full mag demo in full auto to see how large of a spread we get with this gun jumping around. If you want information on specifications and details along with some close up video of the Cybergun Licensed L6 .50AE Desert Eagle GBB Airsoft Pistolthen watch my Table Top Video for it here.
Starting off with my Chronograph test, the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol was able to get a 5 shot average of 392 fps with the fasters round hitting 400 fps and the slowest Airsoft BB recording 387 fps. Again I was using .20 gram Airsoft BB’s and the indoor temperature was around 20 degrees Celsius which is close to 70 degree Fahrenheit for reference so so the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol performed even better than the claimed on the box 380 fps.
Moving on to the accuracy portion of my Field Test Test for the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol, I carefully placed 10 rounds into my fresh paper target and was a bit dissapoitned in the rather spread out group I got. I feel like this is because of the high fps and lighter choice of Airosft BB I used for this test. When shooting a gun with higher fps it is best to use heavier Airsoft BB’s at least when it comes to accuracy as they won’t get that beach ball effect of floating around so much. I did also shoot the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol in Full auto which does rock around a lot because of the heavy blowback recoil and as expected BB’s kind of went all over but if I was shooting at a human sized target from that range I am sure most rounds would have found their intended target.
Overall the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol is a really nice Airsoft pistol. I love the way it looks and feels to hold in the hand and the blowback operation is very noticeable. It also shoots really hard for an Airsoft Pistol and other than the semi auto accuracy which may be corrected using heavier BB’s, it really does have a lot going for it. I may have to test it out again using heavier Airsoft BB’s to see if this improves accuracy for me at 30 feet out.
Trigger Pull: The trigger pull on the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol is single action only which means you will need to rack the slide to not only draw the hammer back but to also chamber the first round. After that the blowback action will do this for you until you are out of ammo and then the slide will lock back. You can also manually draw the hammer back if a round is already chambered. The trigger itself is really nice, it’s light, super short with a crisp light release perfect for fast action shooting.
Accuracy: At this point I have not made my Field Test Shooting portion of my review for the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol so I really don’t know what to expect? KWC claims an fps of 360 using CO2 as its power source and it is a realistic velocity based on previous Velocity tests with similar KWC Airsoft Guns. In terms of accuracy, again I have no idea since I have not reviewed this version of Desert Eagle before. So stay posted till next week when I make the Field Test Shooting Review for it.
Build Quality: Overall the metal and plastic build quality of the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol is good. It is mostly metal with a plastic frame, the real steel version would have an aluminum frame and has a weight closer to 4 pounds total so a bit lighter in terms of weight compared to the powder burning version. The fit and finishes look good.
Realism: The KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol is an excellent Replica Airsoft version of the real steel L6 Desert Eagle including the top and bottom rails and the ported front barrel. It also has full blowback action and you can fully field strip it. I like the addition of the fingered grips which I think adds ot the overall looks and function of this Airsoft Pistol.
Pros:
Lots of metal and good overall weight to it.
Very accurate replica of Desert Eagle L6.
Ergonomic rubberized grips.
Semi and full auto selectable.
Adjustable hop-up.
No orange tip.
CO2 for more power over GBB.
Uses standard KWC CO2 Desert Eagle magazines.
Picatinny rail top and bottom for lots of accessory mounting options.
Great light weight single action only trigger with super short take-up.
Cons:
Frame is plastic so compared to real steel version is much lighter.
Non adjustable sights, also all black so may be hard to see on darker targets.
No trademarks since non-licensed version via KWC direct.
Very large gun with large grips so not suitable for smaller handed shooters.
Comments: Going off just the looks and feel for the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol I can say for sure I do like it compared ot the standard KWC Desert Eagle with its venting up front and its ergonomic rubberized grips. I hope when I perform the Field Test Shooting Video fo fit it it performs well as the price point is good at around $200 Canadian and who doesn't want to have a Desert Eagle in their Replica Airgun collection at the end of the day!
My Table Top Video of the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol:
In this Preview Unboxing Video I take a look at three new products just listed in our Replica Airguns Store. Two are products from Umarex both being CO2 4.5mm Steel BB and one is a CO2 powered KWC Blowback Airsoft Pistol. I don’t go into a ton of detail in this video but go over what is listed on the box and a quick walk around of each product.
First up I show off the KWC DE L6 CO2 Blowback Airsoft Pistol, it is much like the Cybergun Desert Eagle L6 I reviewed but without the orange tip and with notched pistol grips, also all back which is classic and looks great. This Blowback pistol shoots 6mm Airsoft BB’s at around 360 fps and has a full size dropout metal magazine that holds the CO2 along with 21 rounds.
Next I showcase a rather entry level 4.5mm CO2 BB Pump Action Rifle called the Umarex NXG Pump Shot that is a mostly plastic lighter weight build perfect for smaller or younger shooters. It uses CO2, shoots 4.5mm Steel BB’s and comes with a drop out 10 round rotary magazine. You will have to pump it before each shot but this makes the trigger fairly light.
Lastly but perhaps my favorite in this lineup I take a look at the CO2 4.5mm Blowback Umarex Legends M3 Grease Gun. Just like the real steel .45 caliber Grease Gun it is capable of full auto and also shoots in semi auto. You will find a full size drop out metal magazine that holds two CO2 cartridges along with 60 4.5mm steel BB’s. Thats a lot of rounds!
Starting with what the actual velocity of the KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol. I made sure to keep the Sea Can and Airgun nice and warm before making this test and I also placed a brand new 12 gram CO2 cartridge in it and went with lead pellets I am guesstimating where around 7 grain so not super heavy or super light, definitely not high velocity alloy pellets. I was a bit shocked that my average fps was no where near the claimed 360 fps. My 5 shot average came to 259 fps with a couple shots even shooting under 200 fps which I through out. Is that good enough for shorter range plinking? I would say so but but way off the claimed 360 fps. Maybe the manufacturers claim was using high velocity light weight alloy pellets?
Next as with all my Field Test Shooting Videos for the KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol I performed my accuracy portion of the test and reloaded the 16 round magazine which is actually a dual 8 round rotary magazine you manually switch sides to unload all rounds. My first 8 shots for the most part where decently centered perhaps a bit to the right but the grouping was rather spread out close to a around 5 inches maybe even a bit more. I then rotated the magazine to the other side of fully loaded pellets and this time I had several malfunctions/jams where rounds did not rotate properly therefore getting squished rather than going down the barrel. I have a feeling this is a problem with this specific magazine as I had the same problem during my Velocity test. I even switched to pointed pellets for the accrual test from flat head pellets but it did not seem to help. The best I could do on this day with this gun was to get around a 5-6 inch grouping which is not very good for a pellet shooter at 30 feet out
As I mentioned in the video I only test the guns, I don’t make them and as with any product out there it is possible I got a lemon since it seems to me like only one side of the rotary magazine was giving me the problems with jamming pellets. That said even the side that was more consistent did not shoot a very tight grouping for me. If it was my money to spend and I wanted a 24/7 styled Replica Airgun I would probably go with the blowback CO2 BB version since I had a lot better performance from that pistol with the addition of blowback action and a much lighter single action trigger.
