Can I use Airsoft BB's in my BB Pistol? I would have to say this is by far the number one question I get asked in the comments section of my Vimeo videos. I have made several videos where this question gets addressed within the video but so far to date I have not made a stand alone video just covering Airsoft BB use in BB Guns.
So here it is, and now I have a video I can link to this so very common question, if you where wondering about this yourself than please watch my YouTube Video on this topic as it goes into a fair amount of detail about it.
The short answer to this question is no, you can not use 6mm Airsoft BB's in a 4.5mm Steel BB Pistol or Rifle. For the simple reason that 6mm is larger than 4.5mm and so the physical diameter of a6mm Plastic Airsoft BB is just to large to fit inside of a 4.5mm Steel BB magazine or barrel.
People have commented about using a 4.5mm plastic Airsoft BB in a 4.5mm BB gun and yes this could in theory be an option but I discuss why I feel this is not a good idea based on size and mass.
In this video I feature my top five favorite BB pistols for early 2016. That said there are lots of other BB pistols I truly love and enjoy but I had to pick 5 so these are them! You may notice that many of them are blowback, I do like the blowback guns after all and this is my top 5 pick so naturally many of them will have blowback action.
Here is a list of my top 5 guns featured in this video not necessarily in order of choice:
With the popularity of the KWC - Cybergun 1911 Blowback CO2 Pistols and how super realistic they are in so many ways, it is no surprise that people often ask me if they can replace the original grips with grips made for a real 1911.
The short answer is yes you can! You will have to be prepared to remove just a little bit of material from the backside of both grips near the bottom of the handle where there is an area that has been flared out to accommodate the CO2. Not really a big deal, you can use a Dremel for the quick and easy approach or even some sand paper if you don't mind taking a little more time.
I'm getting close to uploading 600 videos now over on the Replica Airguns Vimeo channel, so there are bound to be a lot of similar questions and popular discussions. In this Replica Airguns Vimeo Video I address what I feel are my Top 10 Most Common Airgun Questions and Discussions.
Whether you like it or not, most of us have come across an Airgun with an ugly orange tip on it at some point. In most cases you will find the intrusive orange or red tips on Airsoft guns that shoot plastic BB's, in some cases you will even find them on Airguns that shoot either lead pellets and/or steel BB's.
It really comes down to where you live as to what your local gun laws have determined is required for your area. You may even live in a region where Airguns and Airsoft guns are not allowed at all! So for you a red or orange tip on the front would be welcome if it would allow you to own an Airgun or Airsoft gun. What about the entire gun being painted a bright color, well that is the case for some folks so again having a red or orange tips may not be as bad as it originally seemed...
In Canada where I live, we used to only be allowed Airsoft guns that had clear sections as our replica gun laws are very strict and all black Airsoft guns would have fallen iinto the "replica" category if they did not have large clear plastic see-through sections on them. This clear section law was revised somewhat over the last several years to allow for all black Airsoft guns here in Canada. It was determined that many Airsoft guns with higher fps limits could cause a serious injury to a human, making them less of a toy in the eyes of the law and more of a weapon. Because of this, Airsoft guns that are capable of shooting a .20 gram plastic BB at a velocity of 360 fps or "higher" are now considered to be similar in the eyes of the law to a regular steel BB or lead pellet shooting Airgun. In Canada, Pellet and Steel BB guns are actually considered firearms of a sort so this allows the higher fps Airsoft guns to be all black since it can not be a replica of a firearm if it is in fact considered to be a firearm by law.
The long and short of all of this is that here in Canada we do not require our Airsoft guns to have orange or red tips since they are considered more or less to be just like any other Airgun and our Airguns do not have red or orange tips either.
Getting back to the title of this article "No Orange Tip On Your Airsoft Gun! Are You Insane?" I often get folks from the US giving me heck for removing the orange tips from my Airsoft guns or asking me why my Airsoft guns don't have them in the first place. These people even state that I could get in a lot of trouble for this! Perhaps they think I live in the US or that US laws govern Canada as well? I am not sure but I can say for the record that I am not breaking any laws at least here in Canada where I live.
I know in the US that wholesalers and retailers by law have to sell Airsoft guns with the affixed orange tips on them, once the end user receives that gun and depending on which state they live in, it may or may not be legal to remove the orange tip. Again, you will need to look into your local state laws as they are different from state to state in the US.
In this Video Review I show you around the G&G CM16 Raider and Carbine AEG Airsoft Rifle's. Since these AEG Airsoft AR Rifles are a bit large to showcase using my traditional Table Top location I move into my gym and take each gun out of its box to have a good look at them. I talk about some of the main features and specification. The main features being these G&G CM16 AR15 / M16 AEG Airsoft Rifles are all really well priced but also very well made for their rather low overall cost. They do have a primarily all Nylon Fiber build even in the receivers but they still have a nice 4.6 to 5.7 pound weight to them, and once dressed up with a few accessories they come in at a perfect weight that is not too heavy to carry around in just about any game situation. The Nylon material in some way is a better choice in terms of getting scratched and dinged since they will not mark up as easily as painted metals will.
This Video Review focuses on the shooting aspects of the Baikal MP-53M. I test it out to see what kind of velocity it can achieve and I also perform an accuracy test to see how straight and true it shoots.
My first test, the velocity test I performed using my Chronograph shooting 5 7 grain RWS lead pellets. the fps ranged from 303 to 341 fps with an average 5 shot reading of 319 feet per second. Keep in mind the Baikal MP-53M is strictly a target shooter and is not meant for pest control so these readings are perfectly adequate for this this pistols purposes. The lower velocity also makes for a nice easy cocking effort.
Moving on to the accuracy portion of this field test shooting review, I performed my usual 30 foot paper target test using a semi rested stance standing in the back with a sandbag up front to rest my hands on. This position is fairly stable but not perfect so there is always so human factor to consider and with a springer which I am not super proficient at so there where a couple of shot that I pulled. For the most part the majority of my shots with stayed within about a 1 inch grouping but I know with practice the Baikal MP-53M would shoot under a half inch for sure.
A couple of side notes about the Baikal MP-53M Break Barrel .177 Pellet Air Pistol... It has a super nice trigger which is very light and crisp which will aid in accuracy for sure. I did find that the rear sight moved around a little bit, it seemed to rise a bit and I had to press down on it just a little to keep my shots consistent. The spring is not terribly strong so recoil is minimal for a springer and it is very easy to cock.
Ammunition Capacity: 17 round full size metal magazine.
FPS: 380 using .20 gram BB's.
This is a Mini Review for the KWC/Cybergun Colt M1911 A1 CO2 Blowback Airsoft Pistol. I have already reviewed other KWC version of this all metal realistic CO2 blowback pistol in both 6mm Airsoft and 4.5mm Steel BB and in a variety of different finishes so if you are interested in a more detailed write up for the Cybergun Colt M1911 A1, you can check out the below links where I have reviewed many variations of virtually the same blowback CO2 airgun made by KWC.
Ammunition Capacity: 15 round full size metal magazine.
FPS: 300+
Trigger Pull: The trigger pull on the ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol is I would have to say one of the nicest 1911 single action triggers I have tested so far. The take-up is very slight with an extremely light trigger pull required to release the hammer. Any lighter and I would say it would be too light and perhaps prone to accidental firing.The three hole tactical trigger extends out a little further than some 1911's but feels secure on the finger.
Accuracy: At this point I have not shot the ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol but have high expectations based on the overall quality of this pistol and form other reviews I have read on this Airsoft 1911 replica. According to the manufacturers claimed fps, we should get somewhere right around 300 fps. The ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol has an adjustable rear sight for windage and we can take care of elevation using the adjustable hop-up so zoning in the Socom Gear US Marine MEU SOC 1911 to shoot dead center on target should not be too difficult.
Build Quality: The ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol is one of those Airguns that really catches your eye, and once you pick it up and hold it in your hands you discover that not only does it look really great but it also feels really great in your hands! The tolerances of the parts are excellent, everything mechanical is smooth without any friction and you can even see the texture of the metal grain through the quality matt black powder finish.
Realism: The ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol is a a fantastic replica of a real steel MEU SOC 1911 used by the US Marine Corps' Marine Expeditionary Unit (MEU). The balance and weight really make this 1911 Airsoft pistol feel like your holding the real deal, all the mechanic parts function as they would compared to the original and the ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol is fully field stripable.
Excellent quality, durable black powder coat matte finish .
Enhanced Pro-Grip with brass marine inserts
MEU SOC 1911 Licensed.
Three hole tactical trigger with skeleton hammer.
Comes in a hard shell case with Gemtech Outback II 5-inch silencer and lanyard.
Rail for adding accessories.
Cons:
FPS is kind of low for Canada Market so not one we can regularly get in stock.
A bit on the pricy side.
No option of CO2 magazine.
Comments:
With all the BB and Airsoft 1911's out there what makes the ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol stand out from the rest. First off it feel the most believabel when holding it in your hand, it seems ot have that perfect weight and balance that is often hard to replicate in an Airgun. With features like enhanced Pro-Grips with brass marine inserts, MEU SOC 1911 licensing, three hole tactical trigger, ambidextrous safety, super smooth and light single action trigger, White dot adjustable sights and the included hard shell case with lanyard and Gemtech silencer you can not go wrong with the ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol.
My Vimeo Video Review for the ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol:
Action: Semi auto non-blowback, double action only.
Ammunition Type: Steel BBs 4.5mm.
Ammunition Capacity: 21 rounds
FPS: 394 fps/ 120 m/s.
Trigger Pull: The trigger pull on the KWC Metal Slide CQBP M45 A1 Non-Blowback CO2 BB Pistol was about medium to hard but I have definitely experienced heavier trigger pulls on some guns. It is nice that the trigger is in the style of a 1911 and not your typical lever styled trigger like you will find on some 1911 wannabe's. I imagine if the CQBP M45 A1 has a lever style trigger it would have more leverage and be a bit lighter.
Accuracy: I have not shot the KWC Metal Slide CQBP M45 A1 Non-Blowback CO2 BB Pistol but expect it to perform similar to the Cybergun Sig Sauer GSR Sigarms I reviewed a while back since both guns have similar internals so for now until I do my dedicated Field Test review you can read my Cybergun Sig Sauer GSR Sigarms Review: "Accuracy was decent but not outstanding, I got around a 2.5 inch grouping from a 20 foot away free standing position, shooting just to the left and high on the target. I did find that I was able to zone in a bit better with the Cybergun GSR as I got used to the trigger. I also put the Cybergun Sig Sauer GSR through my Chrony Chronograph and got very close the manufacturers 397 claimed feet per second, actually starting off well above it and settling down to around the 370 FPS mark. My 8 shot average on a new CO2 was actually 422 FPS."
Build Quality: You will find a pretty nice balance of metal and plastic on the KWC Metal Slide CQBP M45 A1 Non-Blowback CO2 BB Pistol. The metal slide, magazine barrel and some literals give it a really decent weight in the hand and the fit and fish feel good overall. The trigger and hammer are not the best aspects of the gun in terms of quality as they are both plastic and both kind of made more for show and less for function.
Realism: The KWC Metal Slide CQBP M45 A1 Non-Blowback CO2 BB Pistol looks and feel the part of a M45 1911 A1 including a full size drop out metal magazine, working magazine release and safety. The slide catch release is none functioning and so is the hammer which does not cock back for single action shooting. It would have been nice to have a single action trigger and a working slide to finish off this pistol but it is meant to be more of an entry level pistol at the end of the day.
Should have good FPS and lots of shots per CO2 based on my 4.5mm BB version testing!
Rail for mounting accessories.
Nice white dot sights.
Recessed barrel give it a more realistic look.
True 1911 style looking trigger even though it is double action only.
True 1911 working safety.
Cons:
No blowback - slide does not move either.
Hammer moves but does not cock so no single action shooting.
Non adjustable rear sight.
Trigger action is bit heavy and long so it’s not going to be the fastest action shooter.
Comments:
If you're looking for a lower cost well made 1911 in that classic A1 style but with a little bit of updating like having a Picatinny rail and tactical sights then the KWC Metal Slide CQBP M45 A1 Non-Blowback CO2 BB Pistolmay just be right for you. So it doesn't have blowback or a working slide, on the other hand it has lots of metal on it giving it good weight and feel and with less moving parts there will be less to go wrong down the road. You can also expect to get fps into the 400 range with a decent amount of shots per CO2 so the trade off not having blowback may be worth it for this reason. All in all a nice airgun in the under $100 category.
My Vimeo Videos for the KWC Metal Slide CQBP M45 A1 CO2 Air Pistol:
Trigger Pull: The trigger pull on the KWC Mac 11 M11 is double action only and is rather long and a bit firm so you will get a bit of a finger workout especially when shooting a full 39 rounds from the 4.5mm steel BB version. There is no blowback operation so this is a double action only pistol.
Accuracy: The accuracy and true feet per second performance will be tested when I do my future Field Test Shooting Review shortly (weather permitting).
Build Quality: Overall the KWC Mac 11 M11 CO2 BB - Airsoft Pistol is built fairly well as long as you don't mind the all plastic build. to be honest if you where to drop this all plastic pistol on the ground it would most likely just bounce a couple of times no worse for wear since it is kind of light weight and all. If it was an almost all metal build it would weigh in a lot more and the drop onto a hard surface could easily break the zinc alloy metal parts. That said there is some metal on the KWC Mac 11 M11 CO2 BB - Airsoft Pistol and that would be the folding - sliding stock and of course some internal parts. The rear fold out portion of the stock is actually hardened steel!
Realism: As a replica of a real steel Mac 11 M11, the KWC Mac 11 M11 CO2 BB - Airsoft Pistol looks bang on since it is 1 to 1 scale and at least in terms of looks is virtually identical ot teh real Mac 11. In terms of function, that is a different story since the KWC Mac 11 M11 CO2 BB - Airsoft Pistol does not have many working parts other than the trigger, safety and magazine release. The selector switch, bolt charging handle and bolt are all molded into this gun and their only purpose is to look good! The overall weight is rather light too since most of this Mac 11 pistol is ABS or plastic.
Pros:
First 4.5mm Steel BB Mac 11.
1/1 scale replica definitely looks the part.
Full size drop out magazine that holds the CO2 and BB’s.
High capacity 39 rounds magazine.
Built in metal and steel retractable stock.
Decent fps.
Available in both 4.5mm Steel BB and 6mm Plastic Airsoft versions.
Cons:
Pretty much all ABS, kind of light weight.
No blowback or many working parts.
Kind of long and heavy trigger.
Pretty much everything is moulded into this gun.
Comments:
Too be honest when I first saw the box for the KWC Mac 11 M11 CO2 BB - Airsoft Pistol I was a bit excited, that was until I opened it up and found out I was looking at a pretty much all plastic gun with few working parts and no blowback operation. But after holding it and giving this air pistol a good look over I have to say I am warming up to it a bit more now. After all it is the first Mac 11 M11 4.5mm steel BB pistol that I know of and it 100% looks the part so if you are looking for a replica Mac 11 then this will fill that purpose for sure. Even though it is almost all ABS plastic, this airgun feels solid seems to be really well made. The steel and metal stock is a nice addition and so would have been a metal magazine but overall for a low cost replica BB and Airsoft shooter you do get your moneys worth.
My Vimeo Video Review for the KWC Mac 11 M11 CO2 BB - Airsoft Pistol:
Trigger Pull: The trigger pull on the KWC Makarov PM CO2 Blowback BB Pistol is really nice. It is single action only since it is a blowback pistol that requires racking the slide to chamber the first round. The take-up of the trigger is slight with a crisp light release, the trigger is definitely not going to get in the way of the accuracy of this pistol.
Accuracy: The accuracy and true feet per second performance will be tested when I do my future Field Test Shooting Review shortly (weather permitting).
Build Quality: Excellent, the KWC Makarov PM CO2 Blowback BB Pistol seems to be really well built like the other full blowback KWC BB and Airsoft pistols I have reviewed and shot in the past. The fit and finish is very good but I expect the electromagnetic black coating to wear off in the high spots fairly quickly but this does give the slight worn in real gun look. In terms of quality it looks like KWC may have even gone to extra effort to beef up some of the areas perhaps prone to breakage like the trigger guard since this pistol is made out of Zink based metals rather than hardened steel like you would find in the real firearm.
Realism: I have to say the KWC Makarov PM CO2 Blowback BB Pistol is a really nice replica overall, perhaps one of the best considering it has full cycle blowback with an all metal full sized drop out magazine. Sure the Baikal MP-654K takes the cake in terms of realism since it is practically a real Makarov rechambered to shoot Steel BB's but the MP-654K lacks blowback operation and the ability to fire quickly using a single action trigger. A couple of drawbacks with the KWC Makarov PM CO2 Blowback BB Pistol that are different from the real steel Makarov PM are the thicker trigger guard and butt plate.
Pros:
Has full cycle blowback operation.
Nice heavy blowback spring makes slide nice and snappy, should have good blowback operation.
All metal build.
All metal full size drop out magazine that holds the BB’s and CO2.
Fully field strip-able.
All part function like a real Makarov.
Open ejection port and reassessed barrel.
No ugly CO2 tab.
Seems to have a really nice single action only trigger.
Internal fixed hop-up for improved accuracy and sustained trajectory.
Cons:
Lower fps because of short barrel and presumable heavy blowback operation.
Magazine base sticks forward a bit more and is thicker than a real steel Makarov.
Trigger guard looks to be thicker than a real steel Makarov.
Comments:
The Makarov is one of my favorite pistols, it's a true classic! So the fact that there is yet another Makarov Air pistol on the market is fine with me. And perhaps the KWC Makarov PM CO2 Blowback BB Pistol might just be the best all around Airgun Makarov hitting all the hot spots us Replica Airgun enthusiasts love... Like full blowback operation, a nice light single action trigger, a full size metal magazine that holds the ammo and the CO2 and of course an all metal build with all those working bits and pieces like you would find on the real steel Makarov PM. But you will have to decide for yourself...
My Vimeo Video Review for the KWC Makarov PM CO2 Blowback BB Pistol:
Trigger Pull: The trigger pull on the Baikal MP-53M Break Barrel .177 Pellet Air Pistol is a nice light 2 pounds and the release stage is also crisp, the trigger is not adjustable but it is really nice the way it is with virtually no take-up and a crisp release.
Accuracy: At this point I have only plinked around a bit with the Baikal MP-53M Break Barrel .177 Pellet Air Pistol, I have not really tested it out on a paper target or put any rounds through the Chronograph. It does however seem to have pretty decent power for a low effort springer and I was able to place most shots on my targets down range. Stay posted for my full Field Test Shooting Video where I will put the Baikal MP-53M Break Barrel .177 Pellet Air Pistol through its paces.
Build Quality: The Baikal MP-53M Break Barrel .177 Pellet Air Pistol is made in typical Russian fashion, it may not be super pretty or have the best finishing out there but all the parts are built to last, even the plastic parts are made using weapons grade materials and the 8.5 inch rifled barrel is hammer-forged.
Realism: The Baikal MP-53M Break Barrel .177 Pellet Air Pistol is not a replica gun, it is purely made to be a single shot target pistol for plinking purposes. I would not even recommend the Baikal MP-53M for pest control as it is under powered for that purpose. This pistol is simply for placing lead pellets into targets down range. Nothing more.
Anti-beartrap spring piston mechanism. (No pinched fingers)
Baikal quality hammer-forged rifled barrel.
Fully adjustable sights.
Inexpensive to shoot, all you need is a tin of pellets.
Russian made durability.
Ambidextrous pistol grip.
Easy to cock (only 13 pound cocking effort).
Really light and crisp 2 pound trigger pull.
Cons:
Not supper powerful so not good for pest control.
Trigger is non-adjustable but feels really good anyway.
No easy way to mount a scope or red dot without modifications.
Comments:
The Baikal MP-53M Break Barrel .177 Pellet Air Pistol is a great choice if you're looking for a simple but really well built air springer for target shooting. There are cheaper springers like the Umarex Browning Buckmark and of course there are more expensive springers like the Webley Tempest but if your looking for a reasonably priced, high quality and good overall performing Break Barrel .177 Pellet Air Pistol than the Baikal MP-53M should fit the bill with its hammer-forged rifled barrel, anti-beartrap mechanism, ambidextrous grip and fully adjustable rear sight.
Watch my Vimeo Video Review for this Russian made Spring Piston Air Pistol:
Materials: Metal and plastic (polymer) construction.
Weight: 2.7 pounds (1220 grams).
Length: Open 20.6 inches (522mm) - Closed 10.6 inches (270mm).
Propulsion: AEG.
Action: Semi and full auto.
Ammunition Type: 6mm Airsoft BB's
Ammunition Capacity: 58 round magazine.
FPS: 360+.
Trigger Pull: The trigger pull on the ASG CZ Scorpion VZ61 AEG 6mm Airsoft Gun is what you would expect from your typical AEG Airsoft gun since it is basically an on off switch for the electric circuit, it's light and short. As with most AEG Airsoft guns there is a noticeable sight delay from the time you press the trigger till the gun actually fires a BB since the electric motor must first pull the spring plunger back and then release it to fire a round. Because the ASG CZ Scorpion VZ61 AEG 6mm Airsoft Gun uses a fairly low voltage battery it is a bit more noticeable than with some other AEG Airsoft guns and I am not sure if there are higher output batteries for this style of battery setup.
Accuracy: At this point I have not yet tested the ASG CZ Scorpion VZ61 AEG 6mm Airsoft Gun so I do not have any Chronograph fps velocity or paper target accuracy information to provide to you. I plan on performing my Field Test Shooting Review fairly soon so stay posted for that. I can say that since this is the Canada import version it should shoot a .20 gram plastics Airsoft BB at over 360 fps.
Build Quality: The ASG CZ Scorpion VZ61 AEG 6mm Airsoft Gun is a Chinese made Airsoft gun but I have to say it looks and feels really great. For sure as good as any Taiwanese airgun I have come across! The fit and finish both are excellent and there is a lots of metal in this gun including the main frame, folding stock, front and back sights, charging handle, barrel extension, magazine release, selector switch, pins, trigger and trigger guard.
Realism: The ASG CZ Scorpion VZ61 AEG 6mm Airsoft Gun is is true to scale, size and weight to that of the real steel CZ Scorpion VZ61 as far as I can tell without actually having a real CZ Scorpion VZ61 in my possession. Everything works in the same manor as the real CZ Scorpion VZ61, like the charging handle, magazine release, selector switch, adjustable rear sight and folding stock.
Lots of metal parts for a good overall realistic weight and feel.
Semi and full auto selectable.
Comes with battery and charger.
Comes with rail attachment for add on accessories
Folding metal stock.
Adjustable rear metal sight.
Working charging/cocking handle
Scorpion VZ61 Licensed.
Cons:
No blowback so ejection port does not cycle while firing.
May be hard to locate extra batteries and magazines since it is not a common style Airsoft charging system.
Fold out stock is not that usable, kind of short and low.
Made in China?
Comments:
I am really looking forward to performing my Field Test Shooting review for the ASG CZ Scorpion VZ61 AEG 6mm Airsoft Gun and expect it to perform as good as it looks and feels. In terms of size, the ASG CZ Scorpion VZ61 AEG 6mm Airsoft Gun is not much larger than most pistols yet packs a 58 round magazine and AEG reliability and consistency along with true 58 round mag-dump full auto capability. What an awesome sidearm to carry around as your backup gun or tight quarters weapon choice.
Watch my YouTube Table Top Review of the ASG CZ Scorpion VZ61 AEG 6mm Airsoft Gun:
Ammunition Capacity: 15 round metal stick magazine.
FPS: 380 & 400 fps claimed.
Trigger Pull: Trigger pull on both the Umarex Beretta Elite II and Umarex HK45 is double action only but they don't feel too bad, they have that traditional longer double action pull but I did not find it to be too heavy and the release point is fairly predictable for me which should allow for some good overall accuracy when I do my future Field Test Shooting Review.
Accuracy: I have done a full Felid Test Shooting Review Video for the Umarex HK 45 Metal Slide CO2 4.5mm steel BB Pistol so make sure to check that one out! In summary with the 4.5mm Steel BB version I got a bit higher fps then claimed at 420 fps with a 5 shot string using a brand new CO2 with RWS 5.1 grain zinc coated steel BB's. From 30 feet away shooting on a paper target using a semi rested posting I was able to place 10 BB's within 1.5 inches, almost close to a 1 inch grouping. The shot placement for me was just a tad to the left and a bit down but several shots hit the bulls eye so out of the box accuracy was really good on this low cost BB pistol. Since both the Umarex Beretta Elite II and Umarex HK45 Airsoft pistols share many of the same mechanical qualities, I should expect similar results even using 6mm plastics BB's, perhaps a bit wider grouping but fps should be pretty close to claimed.
Build Quality: The Umarex Beretta Elite II and Umarex HK45 are built fairly basic with few moving parts so there is not much to go wrong, the fit and finish is good and there is metal where it needs to be internally and also in the trigger, magazine and on the HK45 even the slide. Both Airsoft Pistols have decent weight even though there is a fair amount of plastic in them.
Realism: Both Umarex Airsoft pistols are accurate looking replicas of their real steel counterparts, in the case of the Umarex HK45, it is very accurate on almost every detail appearance wise, the Umarex Beretta Elite II is not an exact replica of any one specific Beretta but is based on the Beretta Elite II Brigadier. There is no working slide on either pistol and the slide catch/release and hammer are molded into the plastic. The only working parts would be the safety, magazine release and trigger.
Both have tactical rails for adding on accessories.
Both are fully licensed.
Both have pretty decent weigh to them.
The HK45 has a metal slide and white dot sights front and back
The Elite II has white dot front sight.
Cons:
Both guns are double action only.
Both guns have none working hammers
Neither gun has a working slide or blowback action.
Both guns have red tips.
Non adjustable sights.
Comments:
Considering these Airsoft Pistols are rather low cost, the Umarex Beretta Elite II and Umarex HK45 have a lot going for them! They are fully Beretta and HK licensed through Umarex with a (metal slide in the HK45) and metal parts where you want and need them to be. I am expecting decent accuracy and power from both guns and even the double action triggers are very usable. Sure the both budget Airsoft pistols is a pretty basic airguns with few moving parts but then again simplicity is sometimes better in terms of reliability. If you are an Beretta or HK fan and want low cost well made and good performing Airsoft pistols then checkout these Umarex Airsoft guns.
My Vimeo Table Top Review for the Umarex Beretta Elite II and HK45 CO2 Airsoft Pistols:
Action: Over-under double barrel single action only.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 2 rounds.
Energy: .6 Joules.
Trigger Pull: The trigger pull on the ASG - Marushin Chrome Derringer is single action only so you will have to cock the hammer separately for each of the two shots. The action of the single action trigger is extremely short with virtually no take-up to speak of. The trigger pull is also very light.
Accuracy: This part of the review is yet to be determined as I have not done my Field Test or Shooting tests for this pistol. I will put a link in here when I have done my official Field Shooting Test. I have done a little bit of playing around with the ASG - Marushin Chrome Derringer 6mm Gas Airsoft Pistol and can say it is not going to be the most accurate or powerful gun out there but that's not really what this ultra compact gun is meant for, more of a surprise, hey where did that come from kind of gun!
Build Quality: The ASG Chrome Derringer 6mm Gas Airsoft Pistol is built by Marushin and as a Japanese based company it is going to be mostly plastic but with that said this little pistol is built really well, the mechanical parts that need to be metal are, like the grips hammer, trigger, safety and many of the pins and screws. Everything is tight and the tolerances are excellent. The finish is also pretty much flawless.With the added metal parts this .5 pounds pistol actually feels pretty solid in the hand and it's hard to tell so much of it it is actually plastic.
Realism: The ASG - Marushin Chrome Derringer 6mm Gas Airsoft Pistol looks the part of a real steel Derringer in terms of size and mechanical parts all functioning as they would. Even the over-under barrels are recessed to look like a much larger caliber than 6mm. The only real give away would be the small gas valve located under the handle and of coursee the lighter weight.
Not a lot of meat parts but the metal grips, hammer, trigger and safety seem to add enough weight to make this Derringer feel pretty solid in the hand.
Nice recessed over-under barrels.
Mechanical part feel solid and tight.
Cons:
Main gun build is plastic, typical of Marushin guns.
Not a lot of power from my preliminary testing.
Only 2 shots so make them count!
Comments:
The ASG - Marushin Chrome Derringer is a rather unique 6mm Gas Airsoft Pistol and is not going to make a very good primary weapon or for that matter even a good secondary weapon, but on that off chance you want surprise on your side then this little guy would make a really great last resort gun for when you only have that one shot up close and personal and it's now or never... There's also the fact that it's a Derringer and how cool is that!
My Vimeo Table Top Video Review for this ASG Chrome Derringer 6mm Gas Airsoft Pistol:
Materials: Mostly metal with some plastic construction.
Weight: 2 pounds (900 grams).
Barrel: 2.25 inches, non-rifled.
Propulsion: 12 gram CO2.
Action: Revolver, single & double actions.
Ammunition Type: 4.5mm steel BB's.
Ammunition Capacity: 6 rounds.
FPS: 328 fps (120 m/s).
Trigger Pull: The trigger pull on the Gletcher CLT-B25 357 2.5 Inch CO2 BB Revolver is good in both single and double action, even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, most likely because the spring tension that pushes the inner barrel to make contact with the cylinder is noticeably lighter on the KWC - Gletcher 357's. Even the hammer is smoother and has less wiggle, just a better trigger and hammer mechanism overall.
Accuracy: In terms of power and accuracy, you can checkout my full Field Test Shooting Video here. I did get a nice 2 inch 6 shot grouping on my paper target setup 30 feet away from my standard semi-rested position (sand bag up front and standing in the back). Accuracy was a bit lower than the factory claimed 320 or so fps coming in at an average of 280. I did perform my field test back in May so the weather was not all that warm perhaps effecting peek fps performance somewhat.
Build Quality: The Gletcher CLT-B25 357 2.5 Inch CO2 BB Revolver being mostly metal has a very good build quality, perhaps even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, even the weight of the KWC 357 is noticeably more! The only real plastic or rubber I could find was in the grips and the shell tips. Fit and finish was also good with no noticeable wear or sloppy workmanship.
Realism: The KWC - Gletcher CLT-B25 357 2.5 Inch CO2 BB Revolver overall is a close copy a the real steel 357 styled revolver. I did notice the rear portion of the receiver (between the rear cylinder and hammer) to be a bit longer perhaps to accommodate the CO2 valve length, but other than that this pistol is super close to the original 357 styled revolver it is based on. Again being all metal gives this CO2 BB revolver very realistic weight and feel and the loadable brass shells make using this gun almost exactly like using a real shell loading revolver but for much less cost per shot and of course a lot less recoil on the hands that a real 357 magnum or even when shooting 38 special shells for that matter.
It's a revolver with actual shells! Give you the feeling of loading and shooting a real revolver
Mostly all metal design
lots of detail, well made, fit and finish are both good.
Good overall weight, even for this short 2.5 inch barrel version.
Fully adjustable rear sight for windage and elevation.
Well hidden CO2 Screw.
Recessed barrel.
Nice Trigger pull in both single and double action.
Tactical fingered grips look good and allow for a firm hold.
Cons:
Grips are a bit rough, not as rubbery as they look.
Grips may be a bit large for people with smaller hands.
All black sights not great on dark backgrounds.
FPS could be a bit higher!
Comments:
The Gletcher - KWC CLT-B25 357 2.5 Inch CO2 BB Revolver is yet another addition to the increasing lineup of shell loading revolvers available today in both Steel BB and Airsoft versions. The 2.5 inch reviewed here is meant to be the compact version with its snub nosed barrel but I would have to say it is not a small gun at all coming in at 2 pounds and with rather large grips and a pretty large cylinder to pack around. But then again, that may be just what you are looking for? The shorter barrel does effect the fps performance since longer barreled versions of this same pistol I have tested do shoot much hotter but that is to be expected with pretty much any short barrelled CO2 pistol.
My Vimeo Table Top Review for the Gletcher CLT-B25 357 2.5 Inch CO2 BB Revolver:
Ammunition Capacity: 19 round full size metal magazine.
FPS: 361 using .20 gram BB's.
Trigger Pull: The trigger pull on the Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol is exactly what you would expect from a true single action 1911 styled pistol. It has a short take up and then a nice light and crisp release. The working grip safety is a nice touch requiring your palm to be pressed against it for the trigger and hammer to operate. I also like the Tactical Style Trigger found on the Cybergun Colt 1911 MKIV.
Accuracy: At this point I have not shot the Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol, I imagine it should perform well considering it has spin-up up and a fully adjustable rear sight just in case my shooting is off center a bit. According to the manufacturers claimed fps, we should get somewhere in the mid to high 300 fps range using .20 gram Plastic Airsoft BB's.
Build Quality: I am kind of sitting on the fence with the Colt 1911 MKIV Pistol, on one hand it is an all metal gun with what looks to be fairly decent fit and finish but on the other hand it feels kind of light weight especially with the heavy magazine out of it compared to even the KWC 1911's I have reviewed so often. It may be that more aluminum is being used in this pistol which could actually be a good thing since aluminum would be a higher quality metal over your typical zinc alloy used in most Airsoft and Airguns these days. In terms of operation, I feel like some of the mechanical parts need a bit of break in time, but I have found this to be true with many real guns I have used.
Realism: The Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol is a close replica of the real steel Colt 1911 45 auto but with a more modern Tactical look to it, sporting a Tac style trigger and hammer, double stack magazine, ambidextrous safety and adjustable rear sight. This gun is nearly all metal with very full blowback operation making it feel real to hold in the hand and shoot.
True 1911 single action trigger, excellent pull, very smooth and light.
Accurate trigger design and working grip safety.
Double stack metal magazine holds the CO2 and extra BB’s.
Fully Colt Licensed.
Full adjustable rear sight.
Tactical trigger and hammer with ambidextrous trigger for a more modern look and feel.
Cons:
Comes with the ugly red tip that is really stuck on the gun.
Can kind of tell the Chinese quality a bit.
Licensing is not engraved right into the gun.
Comments:
Overall the Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol is another nice option if you're looking for a Colt Government 1911 Styled Airsoft pistol. Keep in mind this one is Chinese made rather than made in Taiwan. Not sure how that will effect performance and longevity. I have owned Chinese guns that have shot and faired well for me so I am not too worried about it. With its double stack magazine you will find the Cybergun Colt 1911 MKIV to have a fairly large handle so it may not be suitable for those with smaller hands. I do think the Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol features a nice combination of classic Government 1911 looks with a few modern tactical components lie the upgraded trigger, hammer, ambidextrous safety and rear adjustable sight.
My Vimeo Video Review for the Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol:
Trigger Pull: The trigger pull on the KJWorks KP01-E2 Sig Sauer P226 Airsoft Replica is good in both single and double action. Once the slide is pulled back and released the first round is chambered and the hammer will remain back placing the KJWorks P226 in single action mode, the pull is light and the take-up is nice and short, most of your shots will be in single action mode unless you use the de-cocker to lower the hammer for a subsequent double action follow-up shot, double action shots are still pretty light but much longer in order to cock the hammer back.
Accuracy: (I have not shot the KJWorks distributed CO2 Mag version but I have already done a Field Test Shootinng Review for the same KJWORKS gun distributed and licensed by Cybergun in the Gas Mag version. Here is what I had to say about the Cybergun Gas Magazine version: "Shooting the Cybergun Sig P226 from 20 feet out in semi rested position I was able to get very good results. I placed 10 rounds in about 1.5 inches with the shot placement being a bit low possibly due to my barrel mod, adjusting the hop-up may bring the aim point back up to where it should be. The Sig Sauer P226 Airsoft Replica shot right around the 316 fps range while conducting my 5 shot average chrony testing which was lower than advertised but I was using much heavier .20 gram BB's. You can expect to get a full magazine worth of shots out of each gas fill-up but I did notice that as the magazine got colder it did tend to become much less efficient and also seemed to vent a lot of vapor."
Build Quality: The build quality for all KJWorks guns in my opinion is one of the best in the business. Fit and finish is top notch with close tolerances in the working parts as you would find in a real steel gun. The paint is excellent and in general will wear much better than other Airsoft guns out there. The KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol is pretty much all metal and feels it, the recoil spring is nice and firm and all working parts are smooth and crisp when operated.
Realism: The KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol is a replica of the real steel Sig Sauer P226 with the exception of the licensing. The KJWorks KP01-E2 really is a great looking and functioning Airsoft Replica. You can field strip this gun exactly like a real Sig Sauer and all the mechanical parts work just the same including a working de-cocker and adjustable front sight. It is really hard to distinguish the Airsoft version from the real Sig P226 in both looks and feel.
All metal pistol with good overall realistic weight to it.
Very crisp and firm full blowback operation.
Some of the best fit and finish in the industry. Especially in price range.
Nice accurate looking and working Sig Sauer P226 Replica.
Working de-cocker.
White dot sights for quick target acquisition.
Front sight is adjustable for windage.
Full size drop out magazine holds Airsoft BB's and CO2.
Fully field strip-able.
Cons:
No actual Sig Sauer Licensing but very clean look.
CO2 Mag does stick out a bit and add to size
Comments:
I am a huge Sig Sauer fan so I have kind of high expectations with a replica gun! The KJWorks lineup as a whole is really fantastic, and what I say about the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol can be said about the entire lineup. KJWorks makes a super well built product that replicates the real steal version almost exactly other then they shoot Airsoft BB's instead of actual bullets. When holding a KJWorks gun in the hand you can feel the quality, in weight, ballence and especially when operating the slide, trigger and other working parts. Everything just feels so perfect and responsive. For the money you can not go wrong with the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol or any other KJWorks gun for that matter.
My Vimeo Table Top Review of the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol:
Trigger Pull: The trigger pull on the KJWorks Beretta M9 & M9A1 is very good in both single and double action. Double action is a bit longer and heavier than when shooting in single action but not heavy by any means. Single action shooting is short, light and crisp as you would expect when shooting a real steel Beretta 92 style pistol.
Accuracy: I have not done my actual Field Test Shooting video review for the KJWorks M9 and M9A1 Airsoft pistols but I did get the chance to make a short preview video where I shot both guns at some clay pigeons setup around 20 feet away. I was able to pop the center out of the clay pigeons no problem and found that even without any practice I was consistently hitting dead center on most shots. I am not sure exactly what the FPS will be but considering both theses versions of the KJWorks M9 & M9A1 have the CO2 mags they should shoot up into the 360+ fps range using .20 gram Airsoft BB's. Blowback operation is strong and the slides cycle full length. Keep posted for my upcoming Field Test Shooting Video for both pistols.
Build Quality: As expected, the KJWorks M9 & M9A1 build quality is just like all the other KJWorks Airsoft guns I've tested so far, excellent the fit and finish is the best in my opinion even when compared to my my 4.5mm steel BB shooters. When using these guns regularly, areas that are painted like the metal friction areas show very light wear which is rarely the case with metal built blowback Airguns. Again the tolerances between the moving parts like the slide and frame are very tight showing excellent workmanship and machining from KJWorks.
Realism: Both the KJWorks M9 & M9A1 are copies of the real steel popular Beretta M9 & M9A1, it is really hard to tell them apart from the real versions. Both the M9 and M9A1 are very similar in design with the M9A1 having some slight cosmetic differences, the biggest being the addition of a tactical rail built into the frame. Both KJWorks Beretta's can be field stripped in the same manor as a real Beretta M9 Semi Auto pistol and all parts function the same.
Pretty much all metal pistols with good weight to them.
Full heavy blowback operation.
Excellent fit and finish as always with KJWorks pistols.
High capacity full size drop out magazine that holds the Airsoft BB’s and CO2. (Can get Green Gas mags)
Seem to be very accuracy and well centered on target.
White dot sights make it easy to shoot an most backgrounds.
Ambidextrous safeties.
Field strip-able like the real steel versions.
Cons:
Sight are non-adjustable but elevation can be adjusted using the hop-up.
Grips may be a bit wide for some small handed people.
CO2 magazines sticks out a bit when using the CO2 mags.
Comments: The KJWorks Full Metal M9 & M9A1 are yet more examples of excellent full blowback Airsoft pistols from KJWorks. They are built to very high standards, are near perfect replicas of the real steel Beretta M9 & M9A1 and performance is also excellent. Yes the price is slightly higher than a similar Airsoft gun from KWC but the quality on the KJWorks is definitely worth the extra cost. Make sure to drop by our Replica Airguns Canada Store and checkout our new lower pricing on the KJWorks line of Airsoft guns.
My YouTube Table Top Review of the KJWorks M9and M9A1 Full Metal Blowback Airsoft Pistol:
