Ammunition Capacity: 17 round full size metal magazine.
FPS: 380 using .20 gram BB's.
This is a Mini Review for the KWC/Cybergun Colt M1911 A1 CO2 Blowback Airsoft Pistol. I have already reviewed other KWC version of this all metal realistic CO2 blowback pistol in both 6mm Airsoft and 4.5mm Steel BB and in a variety of different finishes so if you are interested in a more detailed write up for the Cybergun Colt M1911 A1, you can check out the below links where I have reviewed many variations of virtually the same blowback CO2 airgun made by KWC.
Ammunition Capacity: 15 round full size metal magazine.
FPS: 300+
Trigger Pull: The trigger pull on the ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol is I would have to say one of the nicest 1911 single action triggers I have tested so far. The take-up is very slight with an extremely light trigger pull required to release the hammer. Any lighter and I would say it would be too light and perhaps prone to accidental firing.The three hole tactical trigger extends out a little further than some 1911's but feels secure on the finger.
Accuracy: At this point I have not shot the ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol but have high expectations based on the overall quality of this pistol and form other reviews I have read on this Airsoft 1911 replica. According to the manufacturers claimed fps, we should get somewhere right around 300 fps. The ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol has an adjustable rear sight for windage and we can take care of elevation using the adjustable hop-up so zoning in the Socom Gear US Marine MEU SOC 1911 to shoot dead center on target should not be too difficult.
Build Quality: The ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol is one of those Airguns that really catches your eye, and once you pick it up and hold it in your hands you discover that not only does it look really great but it also feels really great in your hands! The tolerances of the parts are excellent, everything mechanical is smooth without any friction and you can even see the texture of the metal grain through the quality matt black powder finish.
Realism: The ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol is a a fantastic replica of a real steel MEU SOC 1911 used by the US Marine Corps' Marine Expeditionary Unit (MEU). The balance and weight really make this 1911 Airsoft pistol feel like your holding the real deal, all the mechanic parts function as they would compared to the original and the ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol is fully field stripable.
Excellent quality, durable black powder coat matte finish .
Enhanced Pro-Grip with brass marine inserts
MEU SOC 1911 Licensed.
Three hole tactical trigger with skeleton hammer.
Comes in a hard shell case with Gemtech Outback II 5-inch silencer and lanyard.
Rail for adding accessories.
Cons:
FPS is kind of low for Canada Market so not one we can regularly get in stock.
A bit on the pricy side.
No option of CO2 magazine.
Comments:
With all the BB and Airsoft 1911's out there what makes the ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol stand out from the rest. First off it feel the most believabel when holding it in your hand, it seems ot have that perfect weight and balance that is often hard to replicate in an Airgun. With features like enhanced Pro-Grips with brass marine inserts, MEU SOC 1911 licensing, three hole tactical trigger, ambidextrous safety, super smooth and light single action trigger, White dot adjustable sights and the included hard shell case with lanyard and Gemtech silencer you can not go wrong with the ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol.
My Vimeo Video Review for the ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol:
Action: Semi auto non-blowback, double action only.
Ammunition Type: Steel BBs 4.5mm.
Ammunition Capacity: 21 rounds
FPS: 394 fps/ 120 m/s.
Trigger Pull: The trigger pull on the KWC Metal Slide CQBP M45 A1 Non-Blowback CO2 BB Pistol was about medium to hard but I have definitely experienced heavier trigger pulls on some guns. It is nice that the trigger is in the style of a 1911 and not your typical lever styled trigger like you will find on some 1911 wannabe's. I imagine if the CQBP M45 A1 has a lever style trigger it would have more leverage and be a bit lighter.
Accuracy: I have not shot the KWC Metal Slide CQBP M45 A1 Non-Blowback CO2 BB Pistol but expect it to perform similar to the Cybergun Sig Sauer GSR Sigarms I reviewed a while back since both guns have similar internals so for now until I do my dedicated Field Test review you can read my Cybergun Sig Sauer GSR Sigarms Review: "Accuracy was decent but not outstanding, I got around a 2.5 inch grouping from a 20 foot away free standing position, shooting just to the left and high on the target. I did find that I was able to zone in a bit better with the Cybergun GSR as I got used to the trigger. I also put the Cybergun Sig Sauer GSR through my Chrony Chronograph and got very close the manufacturers 397 claimed feet per second, actually starting off well above it and settling down to around the 370 FPS mark. My 8 shot average on a new CO2 was actually 422 FPS."
Build Quality: You will find a pretty nice balance of metal and plastic on the KWC Metal Slide CQBP M45 A1 Non-Blowback CO2 BB Pistol. The metal slide, magazine barrel and some literals give it a really decent weight in the hand and the fit and fish feel good overall. The trigger and hammer are not the best aspects of the gun in terms of quality as they are both plastic and both kind of made more for show and less for function.
Realism: The KWC Metal Slide CQBP M45 A1 Non-Blowback CO2 BB Pistol looks and feel the part of a M45 1911 A1 including a full size drop out metal magazine, working magazine release and safety. The slide catch release is none functioning and so is the hammer which does not cock back for single action shooting. It would have been nice to have a single action trigger and a working slide to finish off this pistol but it is meant to be more of an entry level pistol at the end of the day.
Should have good FPS and lots of shots per CO2 based on my 4.5mm BB version testing!
Rail for mounting accessories.
Nice white dot sights.
Recessed barrel give it a more realistic look.
True 1911 style looking trigger even though it is double action only.
True 1911 working safety.
Cons:
No blowback - slide does not move either.
Hammer moves but does not cock so no single action shooting.
Non adjustable rear sight.
Trigger action is bit heavy and long so it’s not going to be the fastest action shooter.
Comments:
If you're looking for a lower cost well made 1911 in that classic A1 style but with a little bit of updating like having a Picatinny rail and tactical sights then the KWC Metal Slide CQBP M45 A1 Non-Blowback CO2 BB Pistolmay just be right for you. So it doesn't have blowback or a working slide, on the other hand it has lots of metal on it giving it good weight and feel and with less moving parts there will be less to go wrong down the road. You can also expect to get fps into the 400 range with a decent amount of shots per CO2 so the trade off not having blowback may be worth it for this reason. All in all a nice airgun in the under $100 category.
My Vimeo Videos for the KWC Metal Slide CQBP M45 A1 CO2 Air Pistol:
Trigger Pull: The trigger pull on the KWC Mac 11 M11 is double action only and is rather long and a bit firm so you will get a bit of a finger workout especially when shooting a full 39 rounds from the 4.5mm steel BB version. There is no blowback operation so this is a double action only pistol.
Accuracy: The accuracy and true feet per second performance will be tested when I do my future Field Test Shooting Review shortly (weather permitting).
Build Quality: Overall the KWC Mac 11 M11 CO2 BB - Airsoft Pistol is built fairly well as long as you don't mind the all plastic build. to be honest if you where to drop this all plastic pistol on the ground it would most likely just bounce a couple of times no worse for wear since it is kind of light weight and all. If it was an almost all metal build it would weigh in a lot more and the drop onto a hard surface could easily break the zinc alloy metal parts. That said there is some metal on the KWC Mac 11 M11 CO2 BB - Airsoft Pistol and that would be the folding - sliding stock and of course some internal parts. The rear fold out portion of the stock is actually hardened steel!
Realism: As a replica of a real steel Mac 11 M11, the KWC Mac 11 M11 CO2 BB - Airsoft Pistol looks bang on since it is 1 to 1 scale and at least in terms of looks is virtually identical ot teh real Mac 11. In terms of function, that is a different story since the KWC Mac 11 M11 CO2 BB - Airsoft Pistol does not have many working parts other than the trigger, safety and magazine release. The selector switch, bolt charging handle and bolt are all molded into this gun and their only purpose is to look good! The overall weight is rather light too since most of this Mac 11 pistol is ABS or plastic.
Pros:
First 4.5mm Steel BB Mac 11.
1/1 scale replica definitely looks the part.
Full size drop out magazine that holds the CO2 and BB’s.
High capacity 39 rounds magazine.
Built in metal and steel retractable stock.
Decent fps.
Available in both 4.5mm Steel BB and 6mm Plastic Airsoft versions.
Cons:
Pretty much all ABS, kind of light weight.
No blowback or many working parts.
Kind of long and heavy trigger.
Pretty much everything is moulded into this gun.
Comments:
Too be honest when I first saw the box for the KWC Mac 11 M11 CO2 BB - Airsoft Pistol I was a bit excited, that was until I opened it up and found out I was looking at a pretty much all plastic gun with few working parts and no blowback operation. But after holding it and giving this air pistol a good look over I have to say I am warming up to it a bit more now. After all it is the first Mac 11 M11 4.5mm steel BB pistol that I know of and it 100% looks the part so if you are looking for a replica Mac 11 then this will fill that purpose for sure. Even though it is almost all ABS plastic, this airgun feels solid seems to be really well made. The steel and metal stock is a nice addition and so would have been a metal magazine but overall for a low cost replica BB and Airsoft shooter you do get your moneys worth.
My Vimeo Video Review for the KWC Mac 11 M11 CO2 BB - Airsoft Pistol:
Trigger Pull: The trigger pull on the KWC Makarov PM CO2 Blowback BB Pistol is really nice. It is single action only since it is a blowback pistol that requires racking the slide to chamber the first round. The take-up of the trigger is slight with a crisp light release, the trigger is definitely not going to get in the way of the accuracy of this pistol.
Accuracy: The accuracy and true feet per second performance will be tested when I do my future Field Test Shooting Review shortly (weather permitting).
Build Quality: Excellent, the KWC Makarov PM CO2 Blowback BB Pistol seems to be really well built like the other full blowback KWC BB and Airsoft pistols I have reviewed and shot in the past. The fit and finish is very good but I expect the electromagnetic black coating to wear off in the high spots fairly quickly but this does give the slight worn in real gun look. In terms of quality it looks like KWC may have even gone to extra effort to beef up some of the areas perhaps prone to breakage like the trigger guard since this pistol is made out of Zink based metals rather than hardened steel like you would find in the real firearm.
Realism: I have to say the KWC Makarov PM CO2 Blowback BB Pistol is a really nice replica overall, perhaps one of the best considering it has full cycle blowback with an all metal full sized drop out magazine. Sure the Baikal MP-654K takes the cake in terms of realism since it is practically a real Makarov rechambered to shoot Steel BB's but the MP-654K lacks blowback operation and the ability to fire quickly using a single action trigger. A couple of drawbacks with the KWC Makarov PM CO2 Blowback BB Pistol that are different from the real steel Makarov PM are the thicker trigger guard and butt plate.
Pros:
Has full cycle blowback operation.
Nice heavy blowback spring makes slide nice and snappy, should have good blowback operation.
All metal build.
All metal full size drop out magazine that holds the BB’s and CO2.
Fully field strip-able.
All part function like a real Makarov.
Open ejection port and reassessed barrel.
No ugly CO2 tab.
Seems to have a really nice single action only trigger.
Internal fixed hop-up for improved accuracy and sustained trajectory.
Cons:
Lower fps because of short barrel and presumable heavy blowback operation.
Magazine base sticks forward a bit more and is thicker than a real steel Makarov.
Trigger guard looks to be thicker than a real steel Makarov.
Comments:
The Makarov is one of my favorite pistols, it's a true classic! So the fact that there is yet another Makarov Air pistol on the market is fine with me. And perhaps the KWC Makarov PM CO2 Blowback BB Pistol might just be the best all around Airgun Makarov hitting all the hot spots us Replica Airgun enthusiasts love... Like full blowback operation, a nice light single action trigger, a full size metal magazine that holds the ammo and the CO2 and of course an all metal build with all those working bits and pieces like you would find on the real steel Makarov PM. But you will have to decide for yourself...
My Vimeo Video Review for the KWC Makarov PM CO2 Blowback BB Pistol:
Materials: Metal and plastic (polymer) construction.
Weight: 2.7 pounds (1220 grams).
Length: Open 20.6 inches (522mm) - Closed 10.6 inches (270mm).
Propulsion: AEG.
Action: Semi and full auto.
Ammunition Type: 6mm Airsoft BB's
Ammunition Capacity: 58 round magazine.
FPS: 360+.
Trigger Pull: The trigger pull on the ASG CZ Scorpion VZ61 AEG 6mm Airsoft Gun is what you would expect from your typical AEG Airsoft gun since it is basically an on off switch for the electric circuit, it's light and short. As with most AEG Airsoft guns there is a noticeable sight delay from the time you press the trigger till the gun actually fires a BB since the electric motor must first pull the spring plunger back and then release it to fire a round. Because the ASG CZ Scorpion VZ61 AEG 6mm Airsoft Gun uses a fairly low voltage battery it is a bit more noticeable than with some other AEG Airsoft guns and I am not sure if there are higher output batteries for this style of battery setup.
Accuracy: At this point I have not yet tested the ASG CZ Scorpion VZ61 AEG 6mm Airsoft Gun so I do not have any Chronograph fps velocity or paper target accuracy information to provide to you. I plan on performing my Field Test Shooting Review fairly soon so stay posted for that. I can say that since this is the Canada import version it should shoot a .20 gram plastics Airsoft BB at over 360 fps.
Build Quality: The ASG CZ Scorpion VZ61 AEG 6mm Airsoft Gun is a Chinese made Airsoft gun but I have to say it looks and feels really great. For sure as good as any Taiwanese airgun I have come across! The fit and finish both are excellent and there is a lots of metal in this gun including the main frame, folding stock, front and back sights, charging handle, barrel extension, magazine release, selector switch, pins, trigger and trigger guard.
Realism: The ASG CZ Scorpion VZ61 AEG 6mm Airsoft Gun is is true to scale, size and weight to that of the real steel CZ Scorpion VZ61 as far as I can tell without actually having a real CZ Scorpion VZ61 in my possession. Everything works in the same manor as the real CZ Scorpion VZ61, like the charging handle, magazine release, selector switch, adjustable rear sight and folding stock.
Lots of metal parts for a good overall realistic weight and feel.
Semi and full auto selectable.
Comes with battery and charger.
Comes with rail attachment for add on accessories
Folding metal stock.
Adjustable rear metal sight.
Working charging/cocking handle
Scorpion VZ61 Licensed.
Cons:
No blowback so ejection port does not cycle while firing.
May be hard to locate extra batteries and magazines since it is not a common style Airsoft charging system.
Fold out stock is not that usable, kind of short and low.
Made in China?
Comments:
I am really looking forward to performing my Field Test Shooting review for the ASG CZ Scorpion VZ61 AEG 6mm Airsoft Gun and expect it to perform as good as it looks and feels. In terms of size, the ASG CZ Scorpion VZ61 AEG 6mm Airsoft Gun is not much larger than most pistols yet packs a 58 round magazine and AEG reliability and consistency along with true 58 round mag-dump full auto capability. What an awesome sidearm to carry around as your backup gun or tight quarters weapon choice.
Watch my YouTube Table Top Review of the ASG CZ Scorpion VZ61 AEG 6mm Airsoft Gun:
Ammunition Capacity: 15 round metal stick magazine.
FPS: 380 & 400 fps claimed.
Trigger Pull: Trigger pull on both the Umarex Beretta Elite II and Umarex HK45 is double action only but they don't feel too bad, they have that traditional longer double action pull but I did not find it to be too heavy and the release point is fairly predictable for me which should allow for some good overall accuracy when I do my future Field Test Shooting Review.
Accuracy: I have done a full Felid Test Shooting Review Video for the Umarex HK 45 Metal Slide CO2 4.5mm steel BB Pistol so make sure to check that one out! In summary with the 4.5mm Steel BB version I got a bit higher fps then claimed at 420 fps with a 5 shot string using a brand new CO2 with RWS 5.1 grain zinc coated steel BB's. From 30 feet away shooting on a paper target using a semi rested posting I was able to place 10 BB's within 1.5 inches, almost close to a 1 inch grouping. The shot placement for me was just a tad to the left and a bit down but several shots hit the bulls eye so out of the box accuracy was really good on this low cost BB pistol. Since both the Umarex Beretta Elite II and Umarex HK45 Airsoft pistols share many of the same mechanical qualities, I should expect similar results even using 6mm plastics BB's, perhaps a bit wider grouping but fps should be pretty close to claimed.
Build Quality: The Umarex Beretta Elite II and Umarex HK45 are built fairly basic with few moving parts so there is not much to go wrong, the fit and finish is good and there is metal where it needs to be internally and also in the trigger, magazine and on the HK45 even the slide. Both Airsoft Pistols have decent weight even though there is a fair amount of plastic in them.
Realism: Both Umarex Airsoft pistols are accurate looking replicas of their real steel counterparts, in the case of the Umarex HK45, it is very accurate on almost every detail appearance wise, the Umarex Beretta Elite II is not an exact replica of any one specific Beretta but is based on the Beretta Elite II Brigadier. There is no working slide on either pistol and the slide catch/release and hammer are molded into the plastic. The only working parts would be the safety, magazine release and trigger.
Both have tactical rails for adding on accessories.
Both are fully licensed.
Both have pretty decent weigh to them.
The HK45 has a metal slide and white dot sights front and back
The Elite II has white dot front sight.
Cons:
Both guns are double action only.
Both guns have none working hammers
Neither gun has a working slide or blowback action.
Both guns have red tips.
Non adjustable sights.
Comments:
Considering these Airsoft Pistols are rather low cost, the Umarex Beretta Elite II and Umarex HK45 have a lot going for them! They are fully Beretta and HK licensed through Umarex with a (metal slide in the HK45) and metal parts where you want and need them to be. I am expecting decent accuracy and power from both guns and even the double action triggers are very usable. Sure the both budget Airsoft pistols is a pretty basic airguns with few moving parts but then again simplicity is sometimes better in terms of reliability. If you are an Beretta or HK fan and want low cost well made and good performing Airsoft pistols then checkout these Umarex Airsoft guns.
My Vimeo Table Top Review for the Umarex Beretta Elite II and HK45 CO2 Airsoft Pistols:
Action: Over-under double barrel single action only.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 2 rounds.
Energy: .6 Joules.
Trigger Pull: The trigger pull on the ASG - Marushin Chrome Derringer is single action only so you will have to cock the hammer separately for each of the two shots. The action of the single action trigger is extremely short with virtually no take-up to speak of. The trigger pull is also very light.
Accuracy: This part of the review is yet to be determined as I have not done my Field Test or Shooting tests for this pistol. I will put a link in here when I have done my official Field Shooting Test. I have done a little bit of playing around with the ASG - Marushin Chrome Derringer 6mm Gas Airsoft Pistol and can say it is not going to be the most accurate or powerful gun out there but that's not really what this ultra compact gun is meant for, more of a surprise, hey where did that come from kind of gun!
Build Quality: The ASG Chrome Derringer 6mm Gas Airsoft Pistol is built by Marushin and as a Japanese based company it is going to be mostly plastic but with that said this little pistol is built really well, the mechanical parts that need to be metal are, like the grips hammer, trigger, safety and many of the pins and screws. Everything is tight and the tolerances are excellent. The finish is also pretty much flawless.With the added metal parts this .5 pounds pistol actually feels pretty solid in the hand and it's hard to tell so much of it it is actually plastic.
Realism: The ASG - Marushin Chrome Derringer 6mm Gas Airsoft Pistol looks the part of a real steel Derringer in terms of size and mechanical parts all functioning as they would. Even the over-under barrels are recessed to look like a much larger caliber than 6mm. The only real give away would be the small gas valve located under the handle and of coursee the lighter weight.
Not a lot of meat parts but the metal grips, hammer, trigger and safety seem to add enough weight to make this Derringer feel pretty solid in the hand.
Nice recessed over-under barrels.
Mechanical part feel solid and tight.
Cons:
Main gun build is plastic, typical of Marushin guns.
Not a lot of power from my preliminary testing.
Only 2 shots so make them count!
Comments:
The ASG - Marushin Chrome Derringer is a rather unique 6mm Gas Airsoft Pistol and is not going to make a very good primary weapon or for that matter even a good secondary weapon, but on that off chance you want surprise on your side then this little guy would make a really great last resort gun for when you only have that one shot up close and personal and it's now or never... There's also the fact that it's a Derringer and how cool is that!
My Vimeo Table Top Video Review for this ASG Chrome Derringer 6mm Gas Airsoft Pistol:
Materials: Mostly metal with some plastic construction.
Weight: 2 pounds (900 grams).
Barrel: 2.25 inches, non-rifled.
Propulsion: 12 gram CO2.
Action: Revolver, single & double actions.
Ammunition Type: 4.5mm steel BB's.
Ammunition Capacity: 6 rounds.
FPS: 328 fps (120 m/s).
Trigger Pull: The trigger pull on the Gletcher CLT-B25 357 2.5 Inch CO2 BB Revolver is good in both single and double action, even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, most likely because the spring tension that pushes the inner barrel to make contact with the cylinder is noticeably lighter on the KWC - Gletcher 357's. Even the hammer is smoother and has less wiggle, just a better trigger and hammer mechanism overall.
Accuracy: In terms of power and accuracy, you can checkout my full Field Test Shooting Video here. I did get a nice 2 inch 6 shot grouping on my paper target setup 30 feet away from my standard semi-rested position (sand bag up front and standing in the back). Accuracy was a bit lower than the factory claimed 320 or so fps coming in at an average of 280. I did perform my field test back in May so the weather was not all that warm perhaps effecting peek fps performance somewhat.
Build Quality: The Gletcher CLT-B25 357 2.5 Inch CO2 BB Revolver being mostly metal has a very good build quality, perhaps even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, even the weight of the KWC 357 is noticeably more! The only real plastic or rubber I could find was in the grips and the shell tips. Fit and finish was also good with no noticeable wear or sloppy workmanship.
Realism: The KWC - Gletcher CLT-B25 357 2.5 Inch CO2 BB Revolver overall is a close copy a the real steel 357 styled revolver. I did notice the rear portion of the receiver (between the rear cylinder and hammer) to be a bit longer perhaps to accommodate the CO2 valve length, but other than that this pistol is super close to the original 357 styled revolver it is based on. Again being all metal gives this CO2 BB revolver very realistic weight and feel and the loadable brass shells make using this gun almost exactly like using a real shell loading revolver but for much less cost per shot and of course a lot less recoil on the hands that a real 357 magnum or even when shooting 38 special shells for that matter.
It's a revolver with actual shells! Give you the feeling of loading and shooting a real revolver
Mostly all metal design
lots of detail, well made, fit and finish are both good.
Good overall weight, even for this short 2.5 inch barrel version.
Fully adjustable rear sight for windage and elevation.
Well hidden CO2 Screw.
Recessed barrel.
Nice Trigger pull in both single and double action.
Tactical fingered grips look good and allow for a firm hold.
Cons:
Grips are a bit rough, not as rubbery as they look.
Grips may be a bit large for people with smaller hands.
All black sights not great on dark backgrounds.
FPS could be a bit higher!
Comments:
The Gletcher - KWC CLT-B25 357 2.5 Inch CO2 BB Revolver is yet another addition to the increasing lineup of shell loading revolvers available today in both Steel BB and Airsoft versions. The 2.5 inch reviewed here is meant to be the compact version with its snub nosed barrel but I would have to say it is not a small gun at all coming in at 2 pounds and with rather large grips and a pretty large cylinder to pack around. But then again, that may be just what you are looking for? The shorter barrel does effect the fps performance since longer barreled versions of this same pistol I have tested do shoot much hotter but that is to be expected with pretty much any short barrelled CO2 pistol.
My Vimeo Table Top Review for the Gletcher CLT-B25 357 2.5 Inch CO2 BB Revolver:
Ammunition Capacity: 19 round full size metal magazine.
FPS: 361 using .20 gram BB's.
Trigger Pull: The trigger pull on the Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol is exactly what you would expect from a true single action 1911 styled pistol. It has a short take up and then a nice light and crisp release. The working grip safety is a nice touch requiring your palm to be pressed against it for the trigger and hammer to operate. I also like the Tactical Style Trigger found on the Cybergun Colt 1911 MKIV.
Accuracy: At this point I have not shot the Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol, I imagine it should perform well considering it has spin-up up and a fully adjustable rear sight just in case my shooting is off center a bit. According to the manufacturers claimed fps, we should get somewhere in the mid to high 300 fps range using .20 gram Plastic Airsoft BB's.
Build Quality: I am kind of sitting on the fence with the Colt 1911 MKIV Pistol, on one hand it is an all metal gun with what looks to be fairly decent fit and finish but on the other hand it feels kind of light weight especially with the heavy magazine out of it compared to even the KWC 1911's I have reviewed so often. It may be that more aluminum is being used in this pistol which could actually be a good thing since aluminum would be a higher quality metal over your typical zinc alloy used in most Airsoft and Airguns these days. In terms of operation, I feel like some of the mechanical parts need a bit of break in time, but I have found this to be true with many real guns I have used.
Realism: The Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol is a close replica of the real steel Colt 1911 45 auto but with a more modern Tactical look to it, sporting a Tac style trigger and hammer, double stack magazine, ambidextrous safety and adjustable rear sight. This gun is nearly all metal with very full blowback operation making it feel real to hold in the hand and shoot.
True 1911 single action trigger, excellent pull, very smooth and light.
Accurate trigger design and working grip safety.
Double stack metal magazine holds the CO2 and extra BB’s.
Fully Colt Licensed.
Full adjustable rear sight.
Tactical trigger and hammer with ambidextrous trigger for a more modern look and feel.
Cons:
Comes with the ugly red tip that is really stuck on the gun.
Can kind of tell the Chinese quality a bit.
Licensing is not engraved right into the gun.
Comments:
Overall the Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol is another nice option if you're looking for a Colt Government 1911 Styled Airsoft pistol. Keep in mind this one is Chinese made rather than made in Taiwan. Not sure how that will effect performance and longevity. I have owned Chinese guns that have shot and faired well for me so I am not too worried about it. With its double stack magazine you will find the Cybergun Colt 1911 MKIV to have a fairly large handle so it may not be suitable for those with smaller hands. I do think the Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol features a nice combination of classic Government 1911 looks with a few modern tactical components lie the upgraded trigger, hammer, ambidextrous safety and rear adjustable sight.
My Vimeo Video Review for the Cybergun Colt 1911 MKIV CO2 Blowback Airsoft Pistol:
Trigger Pull: The trigger pull on the KJWorks KP01-E2 Sig Sauer P226 Airsoft Replica is good in both single and double action. Once the slide is pulled back and released the first round is chambered and the hammer will remain back placing the KJWorks P226 in single action mode, the pull is light and the take-up is nice and short, most of your shots will be in single action mode unless you use the de-cocker to lower the hammer for a subsequent double action follow-up shot, double action shots are still pretty light but much longer in order to cock the hammer back.
Accuracy: (I have not shot the KJWorks distributed CO2 Mag version but I have already done a Field Test Shootinng Review for the same KJWORKS gun distributed and licensed by Cybergun in the Gas Mag version. Here is what I had to say about the Cybergun Gas Magazine version: "Shooting the Cybergun Sig P226 from 20 feet out in semi rested position I was able to get very good results. I placed 10 rounds in about 1.5 inches with the shot placement being a bit low possibly due to my barrel mod, adjusting the hop-up may bring the aim point back up to where it should be. The Sig Sauer P226 Airsoft Replica shot right around the 316 fps range while conducting my 5 shot average chrony testing which was lower than advertised but I was using much heavier .20 gram BB's. You can expect to get a full magazine worth of shots out of each gas fill-up but I did notice that as the magazine got colder it did tend to become much less efficient and also seemed to vent a lot of vapor."
Build Quality: The build quality for all KJWorks guns in my opinion is one of the best in the business. Fit and finish is top notch with close tolerances in the working parts as you would find in a real steel gun. The paint is excellent and in general will wear much better than other Airsoft guns out there. The KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol is pretty much all metal and feels it, the recoil spring is nice and firm and all working parts are smooth and crisp when operated.
Realism: The KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol is a replica of the real steel Sig Sauer P226 with the exception of the licensing. The KJWorks KP01-E2 really is a great looking and functioning Airsoft Replica. You can field strip this gun exactly like a real Sig Sauer and all the mechanical parts work just the same including a working de-cocker and adjustable front sight. It is really hard to distinguish the Airsoft version from the real Sig P226 in both looks and feel.
All metal pistol with good overall realistic weight to it.
Very crisp and firm full blowback operation.
Some of the best fit and finish in the industry. Especially in price range.
Nice accurate looking and working Sig Sauer P226 Replica.
Working de-cocker.
White dot sights for quick target acquisition.
Front sight is adjustable for windage.
Full size drop out magazine holds Airsoft BB's and CO2.
Fully field strip-able.
Cons:
No actual Sig Sauer Licensing but very clean look.
CO2 Mag does stick out a bit and add to size
Comments:
I am a huge Sig Sauer fan so I have kind of high expectations with a replica gun! The KJWorks lineup as a whole is really fantastic, and what I say about the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol can be said about the entire lineup. KJWorks makes a super well built product that replicates the real steal version almost exactly other then they shoot Airsoft BB's instead of actual bullets. When holding a KJWorks gun in the hand you can feel the quality, in weight, ballence and especially when operating the slide, trigger and other working parts. Everything just feels so perfect and responsive. For the money you can not go wrong with the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol or any other KJWorks gun for that matter.
My Vimeo Table Top Review of the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol:
Trigger Pull: The trigger pull on the KJWorks Beretta M9 & M9A1 is very good in both single and double action. Double action is a bit longer and heavier than when shooting in single action but not heavy by any means. Single action shooting is short, light and crisp as you would expect when shooting a real steel Beretta 92 style pistol.
Accuracy: I have not done my actual Field Test Shooting video review for the KJWorks M9 and M9A1 Airsoft pistols but I did get the chance to make a short preview video where I shot both guns at some clay pigeons setup around 20 feet away. I was able to pop the center out of the clay pigeons no problem and found that even without any practice I was consistently hitting dead center on most shots. I am not sure exactly what the FPS will be but considering both theses versions of the KJWorks M9 & M9A1 have the CO2 mags they should shoot up into the 360+ fps range using .20 gram Airsoft BB's. Blowback operation is strong and the slides cycle full length. Keep posted for my upcoming Field Test Shooting Video for both pistols.
Build Quality: As expected, the KJWorks M9 & M9A1 build quality is just like all the other KJWorks Airsoft guns I've tested so far, excellent the fit and finish is the best in my opinion even when compared to my my 4.5mm steel BB shooters. When using these guns regularly, areas that are painted like the metal friction areas show very light wear which is rarely the case with metal built blowback Airguns. Again the tolerances between the moving parts like the slide and frame are very tight showing excellent workmanship and machining from KJWorks.
Realism: Both the KJWorks M9 & M9A1 are copies of the real steel popular Beretta M9 & M9A1, it is really hard to tell them apart from the real versions. Both the M9 and M9A1 are very similar in design with the M9A1 having some slight cosmetic differences, the biggest being the addition of a tactical rail built into the frame. Both KJWorks Beretta's can be field stripped in the same manor as a real Beretta M9 Semi Auto pistol and all parts function the same.
Pretty much all metal pistols with good weight to them.
Full heavy blowback operation.
Excellent fit and finish as always with KJWorks pistols.
High capacity full size drop out magazine that holds the Airsoft BB’s and CO2. (Can get Green Gas mags)
Seem to be very accuracy and well centered on target.
White dot sights make it easy to shoot an most backgrounds.
Ambidextrous safeties.
Field strip-able like the real steel versions.
Cons:
Sight are non-adjustable but elevation can be adjusted using the hop-up.
Grips may be a bit wide for some small handed people.
CO2 magazines sticks out a bit when using the CO2 mags.
Comments: The KJWorks Full Metal M9 & M9A1 are yet more examples of excellent full blowback Airsoft pistols from KJWorks. They are built to very high standards, are near perfect replicas of the real steel Beretta M9 & M9A1 and performance is also excellent. Yes the price is slightly higher than a similar Airsoft gun from KWC but the quality on the KJWorks is definitely worth the extra cost. Make sure to drop by our Replica Airguns Canada Store and checkout our new lower pricing on the KJWorks line of Airsoft guns.
My YouTube Table Top Review of the KJWorks M9and M9A1 Full Metal Blowback Airsoft Pistol:
Trigger Pull: The trigger pull on the KJWorks 1911 is very good since it is modeled after a real steel 1911 which makes it short and crisp with a very light trigger pull. There is a very slight take-up at the very beginning of the pull but once your get past this the release is crisp and perceptible. Since it is not a double action trigger you will need to either rack the slide for your first shot or pull the hammer back if you have already chambered a round.
Accuracy: I have not done my actual Field Test Shooting video review for the KJWorks 1911 Airsoft Pistol but I did get the chance to make a short preview video where I shot some clay pigeons setup around 20 feet away. The KJWorks Full Metal CO2 Airsoft 1911 was a lot of fun to shoot at the clay pigeons and I had no trouble hitting them form that range over and over again. I am not sure exactly what the FPS will be but considering this version of the KJWorks 1911 has the CO2 mag it should shoot up into the 360+ fps range using .20 gram Airsoft BB's. Blowback operation is strong and the slide cycles full length. Keep posted for my upcoming Field Test Shooting Video for the KJWorks Full Metal 1911 CO2 Airsoft Pistol.
Build Quality: As expected, the KJWorks 1911 build quality is just like all the other KJWorks Airsoft guns I've tested so far, excellent the fit and finish is the best in my opinion even when compared to any of my 4.5mm steel BB shooters or 6 mm Airsoft pistols. When using KJWorks guns regularly, areas that are painted like the metal friction areas and high spots show very light wear which is rarely the case with metal built blowback Airguns. Again the tolerances between the moving parts like the slide and frame are extremely tight showing excellent workmanship and machining from KJWorks.
Realism: The KJWorks CO2 Full Metal 1911 Blowback Airsoft Pistol copies the real steel very popular even today Colt 1911 A1, it is really hard to tell the KJWorks Airsoft 1911 apart from the real 45 caliber version. The KJWorks 1911 can be field stripped very similarly to a real 1911 Semi Auto pistol and all parts function virtually the same including a working safety, grip safety, slide catch-release, magazine release and hammer.
Pretty much all metal pistol with good realistic weight to it.
Full cycle heavy blowback operation.
Excellent fit and finish as always with KJWorks pistols.
High capacity 28 round full size drop out magazine that holds the Airsoft BB’s and CO2. (Can get Green Gas mags)
Seems to be accurate and well centered on target.
Nice two tone finish.
Working grip safety.
Nice light true single action only trigger.
Field strip-able.
Cons:
Sights are non-adjustable but you can adjust elevation using the hop-up.
Field strips a little different than a real 1911.
CO2 magazine sticks out a bit but KJWorks makes Gas Mags also.
Comments:
I am a big fan of 1911 pistols and love getting my hands on pretty much any version weather it be a Real Steel 45 caliber 1911, a 4.5mm Steel BB version or 6mm Airsoft Pistol. As long as it has that true 1911 single action short light trigger to it. I love the way the slide cycles a bit slower than most semi auto pistols and this can be found in many Airgun and Airsoft version like this KJWorks 1911 making the shooting experience even more realistic. The fit, Finish and overall quality of the KJWorks 1911 over other brands is worth the slight additional costs so if you don't mind paying juts a tad bit more for that extra quality and you're looking for a CO2 1911 then you will not be disappointed with the KJWorks Full Metal CO2 Airsoft 1911.
My Vimeo Table Top Review of the KJWorks M9and M9A1 Full Metal Blowback Airsoft Pistol:
We recently received some new pistols from KJWorks, The CO2 versions in Full Metal of the Colt 1911, the Berretta M9 and the Berretta M9A1. All of these guns are really well made, the fit and finish is excellent. Definitely a very high quality Airsoft pistol and worth spending a little bit more to get this extra quality. We have even lowered the price on many of our new KJWorks guns to make them even more affordable so check them out in our Canada Replica Airguns Store!
So I made a quick demo preview video where I get away from my table top and go outside to show them off a bit and shoot a few rounds through them at some clay pigeons. I did have some camera issues but you will get a good idea on how these guns look and perform.
Materials: Plastic (polymer) and some metal construction.
Weight: 2.7 pounds (1200 grams).
Length: 27.5 inches (700mm).
Propulsion: Spring.
Action: Pump.
Ammunition Type: 6mm Airsoft BB's
Ammunition Capacity: 30 shots per shell.
FPS: 280 (3 shot burst) using .20 gram BB's.
Trigger Pull: The trigger pull on the ASG Franchi SAS 12 feels a bit heavy at first, but since this is not a rapid fire Airsoft gun and needs to be pumped between shots, your finger does not get tired and you will only get 10 shots (3 shot bursts each) off between reloading another full shell. That said the takeup is rather short and the release is predictable once you get used to it being a bit on the heavy side.
Accuracy: Keeping in mind that the ASG Franchi SAS 12 Spring Powered Airsoft Shotgun is in fact a "Shotgun", I did not expect to get sniper rifle accuracy from it and in fact I wanted the three burst rounds to spread out just a bit, similar to how a real shotgun blast would perform. I was very happy with the overall accuracy and spread I got when shooting from 30 feet out in a free standing position.I simple used the open iron sights and all the rounds seemed to center well and spread out just enough to get good coverage on my paper target. In terms of Feet Per Second performance I was not sure what ot expect since three .20 gram BB's where being shot out all at once. I was very happy to see consistent 280 fps velocities which was actually a bit more than I expected considering .60 grams of Airsoft BB's are being shot out with each shot.
Build Quality: This is an almost all external polymer Airsoft Shotgun with the excepting of the outer and inner barrel and a few other parts like the ring mounts, loading bay door and perhaps a few more internal parts being made out of metals. Overall the ASG Franchi SAS 12 feels solid but a bit on the lighter side. I would of liked to have seen more metal parts to perhaps get the weight up a bit but being that the ASG Franchi SAS 12 Short Barreled Airsoft Shotgun is on the light side makes it a great choice as a backup gun that you could easily sling over your back and not be bothered by it all that much.
Good accuracy and fps performance. BB's spread out just right
Light weight and short so great for packing around in tight quarters.
Full Metal Barrel Assembly.
No need for batteries or gas, just load with BB’s and away you go!
Comes with speed loader, extra shell, jam rod and sling strap.
Can also get it with a full stock.
Cons:
May get a bit tiring on the arm after a lot of repetitive shooting.
Would of been nice to include a few more extra shells.
Sights are none adjustable but it centered well for me
Trigger is a bit on the heavy side.
Comments:
The ASG Franchi SAS 12 Short Barreled Airsoft Shotgun is a super fun low cost Airsoft Pump Action Spring Powered Shotgun that shoots pretty hard considering it blast three rounds at a time and the Airsoft BB's hit their mark every time! It's light enough to use in most close quarter combat situations or even strap on your back as a secondary backup weapon. The best part is all you need is a bag of Airsoft BB's and you can shoot all day long, no need for batteries or gas.
Watch my Vimeo Table Top Review of the ASG Franchi SAS 12 Short Barreled Airsoft Shotgun:
Action: Semi auto non-blowback, double action only.
Ammunition Type: Airsoft Plastic 6mm BB's.
Ammunition Capacity: 15 rounds
FPS: 400+
Trigger Pull: The trigger pull on the KWC IWI Jericho 941 CO2 Airsoft Pistol is about medium to hard but defiantly not the worst airgun I have tested. After you quickly shoot off a full CO2 cartridge you may need a bit of a break to rest your trigger finger but the actual shooting experience is just fine and it does not effect accuracy too much once you get used to the pull and break point of the trigger.
"Accuracy was pretty good for a double action shooter, I got around a 1.5 inch grouping from a 20 foot away free standing position, shooting just a hair to the left but a bit on the high side. It is a bit unfortunately that the Jericho 941 does not have sight elevation adjustments as it would make a very accurate airgun otherwise. I also put the Cybergun IWI Jericho 941 through my Chrony Chronograph and got very impressive FPS results, actually starting off and staying well above the claimed manufacturers FPS. My 8 shot average on a new CO2 was a very high 488 FPS, again well above Cybergun's claimed 443 FPS."
Build Quality: Very good, the KWC Model 941 CO2 Airsoft Pistol weighs in at about 2 pounds which is a very hefty weight for a medium sized pistol. The build quality and fit and finish is good all around with decent usage of metal in the slide, magazine, outer barrel and trigger. There are not a lot of moving parts so I would expect good durability since there is not a lot to go wrong with this Airsoft pistol.
Realism: The KWC IWI Jericho 941 Airsoft Pistol is very close to the look, weight, and feel of the real Israel Weapons Industries Jericho 941! Even though it doesn't have a working slide it definitely looks the part with its cut out ejection port, full size drop out metal magazine and recessed metal barrel. The KWC Model 941 does not have any licensed trade marks to speak of but on the positive side of things it also doesn't have the ugly warning instructions written on it either.
All metal full size drop out magazine holds CO2 and Airsoft BB's.
Very accurate IWI Jericho 941 replica in terns of looks, size and weight.
Should get good FPS based on the steel BB version results.
Can expect lots of shots per CO2 based on Steel BB version.
Expecting good accuracy based on the steel BB version results.
Very affordable price at well under $100.
Cons:
Non-blowback and the slide is non-functioning.
The hammer is only for show and does not cock back for single action shots.
Non adjustable rear sights.
Trigger action is bit on the heavy side and gets a bit tiring after lots of shooting.
Comments:
For a relatively inexpensive Airsoft gun you get good value for your money, most importantly a very accurate reproduction of the real IWI Jericho 941 firearm in terms of size, looks and weight. I am hoping to get similar shooting results shooting the KWC Airsoft Model 941 as I did with my BB shooting Cybergun IWI Jericho 941 I tested a few yeas back as it was one of my highest fps BB pistols tested. So make sure to check back shortly for my Field Test Shooting Video Review for this Jericho 941 Airsoft version from KWC.
My Vimeo Videos for the KWC IWI Jericho 941 Airsoft Pistol:
Ammunition Capacity: 15 round full size drop out metal magazine.
FPS: 417.
Trigger Pull: The trigger pull on the ASG MK II is double action only which will make it a bit on the heavy and longer side when compared to a real steel Ruger MK II, it is smooth however and does have a nice satisfying click that sounds like a firing pin being release. The unfortunate part is that the real steel version is a single action only trigger and one that is super short and light so the contrast between the Airsoft and 22LR version may make this gun not practical is an optional training tool if you win the 22LR version also.
Accuracy: This part of the review is yet to be determined as I have not done my Field Test or Shooting tests for this pistol. I will put a link in here when I have done my official Field Shooting Test. For now all I can go on is some feedback from others that have claimed very high fps and excellent accuracy, I am looking forward to finding out for myself! You can watch my Ruger MK I Gas version Field Test Shooting Review to get an idea on how the ASG Ruger MK II version might perform.
Build Quality: ASG as usually distributes quality guns, the fit and finish on the ASG Ruger MK II Dual Tone CO2 6mm Airsoft Pistol is very good and there is use of metal where it needs to be like with the internal mechanical parts, the trigger, the safety, the rear fully adjustable sight and the full size drop out metal magazine that holds the CO2 and the Airsoft BB's. Thee MK II version has a metal upper which adds additional weight over the MK 1's plastic upper.
Realism: The ASG MK II is based on real steel Ruger MK II with the fluted barrel in a two-tone finish and looks very close to a real Ruger MK II. There is no blowback operation or bolt operation so that means that only a double action trigger is possible, this is a bit unfortunate since the real Ruger Mark II has an absolutely smooth and light single action trigger. On the positive side you can field strip the ASG Ruger MK II Dual Tone CO2 6mm Airsoft Pistol just like the real version.
If you own a real Ruger 22LR it would be nice to have for some backyard or basement shooting.
Adjustable rear sight for windage.
Adjustable Hop-up for Elevation.
Full size all metal drop out magazine that holds the CO2 and Airsoft BB's.
Metal upper barrel, Metal trigger, metal safety and many metal internals.
Very satisfying trigger sound, sounds like a real firing pin :)
Field Strips just like the real steel Ruger MK Series.
Cons:
Plastic sights front and back, plastic trigger.
No blowback (Would have allowed for a true single action trigger)
Double Action Only, unlike the real steel version that is single action only.
Comments:
Compared to the my previous review of the ASG Ruger MK I, the MK II for me is a big improvement. The metal upper barrel assembly makes all the difference in terms of weight and feel and with the two-tone look it is for sure a very attractive looking pistol. I also prefer using CO2 for the increased performance of higher fps and less cool down effect over a gas system. I am hopping my Field test Shooting video goes well and the ASG Ruger MK II Dual Tone CO2 6mm Airsoft Pistol performs on point for me.
My Vimeo Table Top Video Review for this ASG Ruger MK II Airsoft Pistol:
Ammunition Capacity: 20 round metal stick magazine.
FPS: 400 fps claimed.
Trigger Pull: Trigger pull on the Umarex HK 45 Metal Slide CO2 BB Pistol is double action only but doesn't feel too bad, it has the traditional longer double action pull but I did not find it to be too heavy and the release point was fairly predictable for me allowing for some good overall accuracy.
Accuracy: I have already done a full Felid Test Shooting Review Video for the Umarex HK 45 Metal Slide CO2 BB Pistol so make sure to check that one out! In summary I got a bit higher fps then claimed at 420 fps with a 5 shot string using a brand new CO2 with RWS 5.1 grain zinc coated steel BB's. From 30 feet away shooting on a paper target using a semi rested posting I was able to place 10 BB's within 1.5 inches, almost close to a 1 inch grouping. The shot placement for me was just a tad to the left and a bit down but several shots hit the bulls eye so out of the box accuracy was really good on this low cost BB pistol.
Build Quality: The Umarex HK 45 Metal Slide CO2 BB Pistol is built fairly basic with few moving parts so there is not much to go wrong, the fit and finish is good and there is metal where it needs to be internally and also the trigger, magazine and slide.
Realism: The Umarex HK 45 Metal Slide CO2 BB Pistol is a very good overall HK 45 Replica BB pistol in terms of size and looks, it has full HK licensing and even has a metal slide and polymer frame like the original real steel HK 45. It is a bit lighter bit not by too much. There is no working slide and the slide catch/release and hammer are molded into the gun. The only working parts would be the safety, magazine release and trigger.
Metal where it matters, slide, magazine, trigger, internals.
Nice replica of the original HK 45.
Fully HK Licensed.
White dot sights easy to sight in your target on most backgrounds.
Decent double action trigger.
Picatinny rail for accessories.
Cons:
None blowback with a fixed slide.
Slide catch/release and hammer are moulded in and none functioning.
Sights are none adjustable.
Comments:
For a rather low cost CO2 4.5mm steel BB pistol, the Umarex HK 45 has a lot going for it! It is fully HK Licensed with a metal slide and metal parts where you want and need it. The accuracy and power are both good and even the double action trigger is very usable. Sure the Umarex HK 45 Metal Slide CO2 BB Pistol is a pretty basic gun with few moving parts but then again simple is sometimes better in terms of reliability. If you are an HK fan and want a low cost well made and good performing BB pistol then checkout the Umarex HK 45.
My Vimeo Table Top Review for the Umarex HK 45 Metal Slide CO2 BB Pistol:
Trigger Pull: Trigger pull on the Webley MK VI .455 CO2 Shell Loading BB Revolver is great in both single and double action, for a shell loading revolver the double action is the best I have come across with next to no friction like I would usually find with shell loading revolvers when shot in double action mode.
Accuracy: I tested the Webley MK VI .455 CO2 Shell Loading BB Revolver on my pool deck first off shooting 6 rounds through my Chronograph. The claimed fps is 427, I got really close to 400 fps in my testing so there is the potential for this revolver to shoot up into the low 400's. When I stepped back 30 feet and shot 6 rounds form my semi rested position, I got a really tight 1 inch group with almost all the rounds landing in the bulls eye. My shots where just a hair to the right but not by much which is good since the sights on this pistol are none adjustable. You can check-out my full Field Test Shooting Video here!
Build Quality: The Webley MK VI .455 CO2 Shell Loading BB Revolver is pretty much an all metal construction other than the plastic grips and any internal seals. The fit and finish is excellent with a great overall weight in the hand. The only complaint I have is that the grips being a thin plastic seem kind of low quality compared to the rest of this otherwise high quality Webley CO2 BB Revolver.
Realism: In terms of replicating a real steel Webley MK VI .455, Webley did a really great job with their CO2 BB firing version. Webley even includes a Small Arms Training Manual based off of the real steel variant. Webley based the BB CO2 MK VI from the original blueprints and the licensing is form the original 1915 version. The only real tell that this is a CO2 BB revolver would be the small safety switch on the lower right side frame and the CO2 valve located right behind the hammer.
Looks amazing and is a very accurate replica of the real steel Webley MK VI.
Great weight and feel in the hand at 2.4 pounds
nice deep Recessed barrel with true .455 caliber opening.
Break barrel design makes it really easy to load the dummy shells.
Hammer / trigger action is great in single and double action.
Webley Licensed.
Well concealed CO2.
Fairly discreet safety location.
No ugly warning instructions on the gun!
Cons:
One of the higher cost shell loading revolvers we sell.
Sights are none adjustable.
Real version would shoot .455 caliber rounds, the dummy shells are actually closer to 357.
Could be a bit loud for some back yard shooters?
Plastic grips seem a bit cheap compared to the rest of this high quality gun.
Comments:
Another classic shell loading CO2 BB Revolver, nothing wrong with that, I remember a time when finding a realistic revolver, even a modern version was hard to do. Now we have a growing selection of super realistic revolvers that replica their original real steel variation with ultra realism. The Webley MK VI .455 CO2 Shell Loading CO2 BB Revolver is no exception and makes for yet another option if you want a well designed, super functional and ultra realistic classic BB revolver.
My Vimeo Table Top Review for the Webley MK VI .455 CO2 Shell Loading CO2 BB Revolver :
I wanted to not only do my Field Test Shooting review for the Umarex 9XP Blowback CO2 BB Pistol but also compare it to the discontinued Umarex SA177 since both guns share most of their internal parts. I had a good idea that both airguns would perform very similarly with perhaps the newer 9XP having the edge due to it being almost 5 years newer.
A with all my current BB Pistol Field Test Shooting Reviews, I test out the real world Feet Per Second performance by shooting 5 rounds through my Chronograph to see what they average out at, of course I use a brand new CO2 for this and my choice of BB was RWS Zinc coated 5.1 grain Steel BB's.
I started out testing the Umarex SA177 to use as my baseline and after about 5 warmup shots, the SA177 came back to life after sitting on the shelf for many years un-shot. My 5 shot string averaged a respectable 397 fps which is pretty good for a blowback pistol!
I then moved on to the newer Umarex 9XP CO2 Blowback Pistol and right away it popped out all 5 shots at over 400 fps with an average of 412 for my 5 shot string. Not only was the Umarex 9XP more powerful but it also had a snappier blowback action and was louder than the SA177 leading me to believe the CO2 valve may be setup to let out a bit more CO2 with each shot.
Stepping back 30 feet from my paper target I proceeded to again first test out the Umarex SA177 for the accuracy portion of this field test. I used my standard semi rested shooting stance, (sand bag up front, standing in the back) since it offers me a pretty stable shooting platform. I generally like to shoot 10 rounds into the paper target but the SA177 for some reason was having some slide lock back issues and I lost a BB in the process. Later on when I reloaded my SA177 I did not have this same problem so I am not sure what was going on. Even though the slide was locking back on some shots it did not really seem to effect the accuracy all that much. I got a main grouping that was about 1.5 inches in diameter and then a couple shots went out of that group extending the diameter to about 2.5 to 3 inches. Still pretty good for a blowback pistol. The shots where fairly well centered on the target.
When I performed the same test using my Umarex 9XP, I did not have any slide lock back issues and was able to get all 10 shot on target although one mystery shot did not seem to make a hole at all even though I clearly heard it fire and hit the target, perhaps it went exactly through an already existing hole? Either way I had a nice 5-6 shot group dead center on the target well under a 1 inch diameter and then 4 shots came outside extending the grouping to about 2 inches, again another well centered grouping!
In conclusion the Umarex 9XP Blowback CO2 BB Pistol is a nice replacement for the SA177, it performs very similarly to the SA177, even perhaps a bit better! To me it felt like the trigger on the Umarex 9XP was a bit heavier than the SA177 but not by much? Maybe the 9XP hammer spring is heavier which would explain the increase in fps. SO if you have been wanting an SA177 but can not find one used, grab yourself one of the Umarex 9XP's, you will not be disappointed :)
