View fullsize

I don't get many Gas Blowback Airsoft Rifles to review all that often so when I get my hands on them I sure have a great time testing them out and feeling the blowback action tapping me in the shoulder as I shoot in semi or full auto modes. Sure Gas Blowback Airsoft Guns don't perform like their AEG counterparts, especially when you're shooting in full auto. You can expect way less rounds in each magazine and even with less rounds the last 5 or 10 shots when shooting rapid fire are going to be compromised but I really don't care because a well made Gas Blowback Airsoft rifle like the KJWorks M4 CQB Carbine GBB is just so much more fun to shoot than an AEG and way more realistic.

View fullsize

So let's get on with my test results for the KJWorks M4 CQB Carbine GBB Airsoft Rifle... The fps consistency was really decent, super consistent when I spaced out my 5 test shots they averaged 377 fps, not really having any low or high fps shots out of the bunch. I did have a full gassed up mag and was using .20 gram plastic 6mm Airsoft BB's for this part of the field test.

Again shooting in semi auto mode, I placed 10 rounds into my paper target setup downrange 30 feet and as per usual I was using a rested shooting setup sitting on a stool and resting the KJWorks M4 CQB Carbine GBB Airsoft Rifle on a sandbag up front. 9 out of the 10 rounds all grouped in about a 3/4 inch group with only 1 round coming outside a bit stretching the 10 shot grouping out to about 1.5 inches. Still really great for a Gas Blowback or any Airsoft rifle for that matter!

View fullsize

Next I shot the rest of the mag in full auto burst mode which was about 20 rounds left in the KJWorks M4 CQB Carbine GBB Airsoft Rifle at this point. As expected the KJWorks M4 CQB Carbine GBB Airsoft Rifle cooled down pretty quick and the last 5 rounds did fire just fine but there was a noticeable drop in power making the rounds shoot low on the target. Keep in mind I was shooting in a not too warm environment, about 15 degrees which is not bad but also not that warm.

View fullsize

I would have liked to have seen the KJWorks M4 CQB Carbine GBB Airsoft Rifle perform as consistently in full auto mode as it did in semi auto but that would have been asking  a bit too much from a Gas Blowback Airsoft rifle. The KJWorks M4 CQB Carbine GBB Airsoft Rifle is a really well put together Airsoft Rifle that didn't let me down in the end.

View fullsize

This was the first time shooting a blank gun in the new Sea Can and I can tell you it was pretty loud inside but of course I was wearing ear protection! In this Blank Gun Shooting video I test out the ARAL Model 1453 and 622K 9mm PAK Blank Guns and put 3 rounds through each of them.

Not everything went as planned. First off my high speed slow motion camera decided to not work :( and secondly I had some technical issues with both guns, well sort of...

View fullsize

Since the manual for the ARAL Model 1453 does not cover what I believed to be a safety on the back of the slide, I had no idea and was surprised to find out that rather than a safety, this selector switch is actually a semi and full auto selector which is kind cool but not so much when you're not expecting your blank gun to be shooting in semi auto :) Keep in mind this semi-full auto switch is only on the all black ARAL Model 1453 and not the two tone version.

Moving on to the ARAL Model 622K 9mm PAK Blank, I have a feeling that perhaps a different brand of ammo may have worked better in it. The 9mm PAK Blanks I used worked OK but I did get a failure to eject and the last round seemed to also not eject properly probably because there was no bullet in the mag too help direct it out of the breach area.

View fullsize

What do yo know, a new Blank Gun Review! It's been a while since I actually saw some new Blank Guns other than our ROHM selection that made it past our wonderful Canada Customs.

So how do the ARAL Model 1453 and ARAL 622K compare to our ROHM Blank Guns? Well to be honest they don't. Our ROHM Blank Guns are much better quality and made in Germany rather than Turkey.

But still it's nice to hold a new Blank Gun in my hands even if it's not the best quality. The two ARAL blank guns I take a look at in this Table Top Video Review are the ARAL Model 1453 and ARAL 622K 9mm PAK versions. Both are front venting and both have double stack 14 round magazines. They also have threaded inner barrels however no flare adaptor came with either on of them and I only got an included manual with the ARAL Model 1453.

View fullsize

In terms of what exactly real steel guns do they look like or resemble? The ARAL Model 1453 is kind of like a big chunky and somewhat ugly looking Glock. I have nick named mine the RoboGlock :)

The ARAL 622K resembles a CZ 75 but it's a fair bit smaller in size and much shorter. The finish on my ARAL 622K is really bad, it looks like someone took a can of spray paint and painted it themselves. But still they are working blank guns, well let's hope so when I test them out in my upcoming Field Test Shooting video... Fingers crossed!

View fullsize

First off make sure to checkout my Table top review for the G&G GPM92 Beretta Mod. 92FS GBB Airsoft Pistol, it really is a nice Beretta Airsoft copy, perhaps one of the best out there!

In the Field Test Shooting Video I perform my standard Chronograph and accuracy tests on the G&G GPM92 Beretta Mod. 92FS GBB Airsoft Pistol. I put 5 rounds through my Chrony Chronograph using .20 gram plastic Airsoft BB's with a full propane filled magazine. My Sea Can indoor airgun range was warmed up sufficiently for a gas gun test but I found the G&G GPM92 Beretta Mod. 92FS GBB Airsoft Pistol did shoot a tad bit slower than the 330 or so claimed fps coming in closer to 300fps. Still totally usable for indoor airgun wars.

View fullsize

Moving onto my accuracy test I placed 10 shots on target 30 feet down range using a rested shooting position, sitting in the back and sand bag up front. This time I was impressed with how tight a group I got, I was able to get the bulk of the shots all within about three quarters of an inch with only two shots hitting just a little outside of this. I did notice the G&G GPM92 Beretta Mod. 92FS GBB Airsoft Pistol was shooting a bit low for me but that can be easily corrected by adjusting the the internal hop-up to raise the shot placement up as required.

The G&G GPM92 Beretta Mod. 92FS GBB Airsoft Pistol has a somewhat relaxed blowback but has plenty to give some recoil feel. You will get at least a full 27 round magazines worth of shots from each gas fill, perhaps even two if you stretch out your shooting a bit. 

View fullsize

Type: Gas Blowback Airsoft Pistol.
Manufacturer:  G&G
Model: GPM92
Materials: Metal slide & frame.
Weight: 2.24 pounds (1016 grams).
Length: 8.9 inches total
Barrel: 4.6 inches, Metal non-rifled smooth bore.
Propulsion: Green gas or propane.
Action: Blowback, single and double action.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 27 rounds.
FPS: 350+ fps.

View fullsize

Trigger Pull: The trigger pull on the G&G GPM92 Beretta Mod. 92FS GBB Airsoft Pistol is very good in both single and double action. Double action is a bit longer but not that much heavier when shooting in single action. Single action shooting is short, light and crisp as you would expect when shooting a real steel Beretta 92 style pistol.

View fullsize

Accuracy: I have not done my actual Field Test Shooting video review for the G&G GPM92 Beretta Mod. 92FS GBB Airsoft Pistol but I did get the chance to shot it quickly in my Sea Can indoor shooting range. Blowback felt good and accuracy seemed tight even though I was shooting free hand. I did notice the G&G GPM92 Beretta Mod. 92FS GBB Airsoft Pistol shot just a little bit low but I can adjust the hop-up slightly to account for it.

View fullsize

Build Quality: Like pretty much all G&G Airsoft guns, the G&G GPM92 Beretta Mod. 92FS GBB Airsoft Pistol build quality is right inline. Fit and finish where excellent and a lot of attention to detail was seen all over this Replica Airsoft Pistol. There is also some new gas valve technology from G&G that should significantly help with freezing in colder or fast shooting situations.

View fullsize

Realism: The G&G GPM92 Beretta Mod. 92FS GBB Airsoft Pistol is an excellent replica of the real steel Beretta Mod. 92FS, the safety even acts as a working decocker. You'll also find 5, 10, and 15 numbered markings on the backside of the magazine that would normally indicate how many bullets are in the magazine, a nice touch for sure! Everything works pretty much the same as it would on a real Beretta M9 including the ability to fully field strip the G&G GPM92 Beretta Mod. 92FS GBB Airsoft Pistol.

Available in the: Replica Airguns Store

View fullsize

Pros:

• Lots of metal and good overall weight.

• Pretty heavy Blowback operation.

• Whirl Cylinder Valve system should expect to get decent amounts of shots per gas fill.

• White dot sights front and back.

• Comes with hard shell case.

• Very detailed full size drop out metal magazine.

• 20mm rail for accessories.

• Comes with high quality speed loader.

• Safety also works as a decocker.

• Threaded removable barrel tip for add on mock suppressor.

View fullsize

Cons:

• Sights are non adjustable.

• A little bit more expensive than some other Beretta M92 full blowback Airsoft pistols

• Barrel opening not as recessed as much as a real 9mm would be.

View fullsize

Comments:

I would have to say the G&G GPM92 is one of the nicest Beretta Model 92FS Airsoft Pistols you are going to find out there. There is a ton of attention to detail for sure, You also get the hard shell case with included high quality speed loader and G&G's new Advanced Safety Release Valve and Revolutionary Whirl Cylinder Valve that help with freeze-up issues. You might pay just a smidgen more that some other similar Blowback Beretta M92's out there but I feel it is well worth it.

My Vimeo Table Top Review of the G&G GPM92 Beretta Mod. 92FS GBB Airsoft Pistol:

View fullsize

I just received some really nice G& G Airsoft guns to share with everyone, I have two CQB Styled AEG rifles and a fantastic Gas Blowback Beretta Mod. 92FS.

The AEG CQB AR or M4 styled rifles are similar in a lot of ways and are super compact and really well built. The G&G ARP-9 has a polymer receiver and hand guard while the G&G ARP-556 has a full metal receiver and hand guard. Both have good weight to them. You will also find Skeletonized PDW stocks and large crown flash hiders on both models along with M-LOK hand guards. Inside you will find upgraded ETU and MOSFET electronics.

View fullsize

Obvious difference are the 9mm style magazine found on the G&G ARP-9 versus the M4 styled high capacity magazine on the G&G ARP-556. You also get an ambidextrous safety sector switch on the G&G ARP-556.

View fullsize

Next I show off the G&G GPM92 Beretta Mod. 92FS Gas Blowback Airsoft Pistol. It comes in a high quality hard plastic case with a well made speed loader. If you place the magazine in the gun you will have room for two magazine in the hard shell case. The G&G GPM92 hold 27 roads in it's double stack magazine that has some interesting new features that help it perform much beet in cold environments and really boost green gas usage. G& G calls them the Whirl Cylinder Valve system and Micro gas filter. Both help eliminate free up in the gun when shooting fast.

The G&G GPM92 Beretta Mod. 92FS is really well made and shoot in double and single action and the safety even works as a decocker. For those looking to add a mock suppressor you will happy to know the G&G GPM92 has a threaded barrel tip.

In this comparison video I look at a variety of different Sig Sauer P226 Airguns and compare them to each other to determine which one I feel is the best Sig Sauer styled Airgun. Of course my choice may not be your choice :) 

Some of the airguns I consider in this comparison video are the: Umarex HPP BB Pistol, the Sig Sauer P226 Pellet Pistol, the Cybergun/KWC X-Five BB Pistols in Standard and Sight Rail versions, the Cybergun KJWorks KP01 P226 Airsoft Pistol, and the KJWorks KP02 P229 Airsoft Pistol.

So which Sig Sauer P226 did I like the best? Make sure to watch my YouTube Video and find out!

View fullsize

Another Airgun Shipping Container (Sea Can) Shooting video and for this indoor filed test I put the KWC - Cybergun M45A1 1911 CO2 Blowback Airsoft Pistol through its paces.

What I am super happy about is that my Chrony Chronograph seems to be working really well as I tested a pellet, steel BB and Airsoft pistol out today and every single round through my Chrony got a reading :)

Now back to the Field Test Shooting Review at hand... I started off by placing 5 shots through my Chrony Chronograph using a brand new CO2 with .20 gram Airsoft BB's and got a really consistent reading for all 5 shots with an average of 357. The lowest shot was 353 and the fastest shot was 364 so all shots where really close in velocity. The container temperature was a near perfect shooting temperature of 23 degrees Celsius which was ideal for optimal CO2 velocity testing.

View fullsize

During my accuracy portion of this Field Shooting Test. I used my new seated in the back and sand bag rested up front shooting position which is about 30 feet back from my paper target. I did notice during my Chrony testing that the Cybergun KWC Colt 1911 Rail Gun M45 A1 CO2 Blowback BB Pistol liked to shoot a bit high, perhaps the hop-up needs a bit of twerking? So for my accuracy testing I shot at the bottom ring of the target, this helped me get more shots on the paper for sure but the Airsoft BB's still moved around a bit vertically. I was able to get about a 4-5 inch 10 shot grouping which is totally acceptable for a close range Airsoft sidearm and in an Airsoft battle I would think even shooting at about 50 feet or so I could easily hit a persons mid section consistently.

The Cybergun KWC Colt 1911 Rail Gun M45 A1 CO2 Blowback BB Pistol has a ton of blowback kick to it and a super nice single action trigger like all the KWC 1911's The modern Tactical coloration and trimmings makes this pistol a great choice as a present day side arm. It's real looker for sure with performance to match!

Buy Colt 1911 Rail Gun Airsoft Pistol in Canada

Buy Colt 1911 Rail Gun Airsoft Pistol in the US

And finally my last Vimeo video from SHOT Show 2017 in Las Vegas! Sorry there is no Interview this time with KWA but I did talk a lot with the KWA folks over at SHOT Show this year and I even got to test out their Laser Targeting System designed to be used with several specifi KWA guns by laser-ammo.com.

Unfortunately we don't carry the KWA brand in the replica Airguns store, a few models sneak in when being distriubted by another company like ASG in the case of the ASG MP9. I would love to carry KWA Airsoft Products in the future since they really do make very high quality Airsoft guns.

KWA has a great selection of Airsoft pistols and rifles in both Gas Blowback and AEG formats. The quality reminds me of the KJWors Airsoft guns we sell in the Replica Airguns Canada Store, you can really feel the quality when you pick them up and hold them for yourself.

It's been a great year for Replica Airguns and I wanted to share with everyone some of my favorites that I reviewed this year. In this Vimeo Video I show some of my top Replica Airgun picks for 2016 and talk a little bit about each one and what I like about it.

Here is a list of the Replica Airguns in this lineup:

• ASG Dan Wesson 715 CO2 Revolver - Comes in 4.5mm Steel BB, 6mm Plastic Airsoft & .177 Pellet.

• Umarex Colt Combat Vet CO2 Blowback 1911 - 4.5mm Steel BB.

• Sig Sauer MPX ASP CO2 Rifle - .177 Pellet.

• Sig Sauer ASP P226 CO2 Blowback Pistol - .177 Pellets.

• Air Venturi ISSC M22 CO2 Blowback Pistol - 4.5mm Steel BB.

• KJWorks KC-02 V2 Ruger 10/22 GBB Rifle - 6mm Plastic Airsoft.

• Umarex S&W M&P40 CO2 Blowback Pistol - 4.5mm Steel BB.

One of the most common types of question I get on my Replica Airguns YouTube channel has to be something like… Why is my Airgun not working? Most of the time the amount of info about the problem is limited to something like… “It was working yesterday but now it’s not working anymore” or something like “when I pull the trigger nothing happens”. My personal favorite is… “I took my gun apart and now it doesn’t work!”

I just made a similar video for Blank Guns and as I said in that video, trying to trouble shoot a mechanical or technical problem over the internet is very difficult, this goes for cars, guns, computers or what have you…

In this Why is My CO2 Airgun Not Working video I will however cover some of the more common and obvious problems I have seen relating to why a CO2 Airgun may not be working properly. I really don’t get a lot of questions about Spring Piston or Pump Airguns so I will be focusing on CO2 Airguns in this video. There will be a lot of crossover with CO2 Airsoft guns so this video may be helpful for some of you Airsofters out there

First let’s get the super obvious stuff out of the way! 

• Did you put a new CO2 cartridge in it and is it pierced all the way?

• Did you load BB’s or Pellets into the Airguns magazine and is the magazine in the gun correctly?

• Is the safety off?

• If the gun is a blowback semi auto single action Airgun then did you pull the slide back prior to the first shot?

CO2 Related Problems:

Not all CO2 cartridges are created equal, they often have slightly different shaped nubs on them and some brands will work better than others in different Airguns. If the shape of the CO2 nub does not fit properly into the valve area then it may not pierce or it could pierce but then not allow you to tighten it all the way losing all the CO2 in the process. If the CO2 is coming form the airguns handle to CO2 Valve area then this is an indication that your problem is related to the area where the CO2 enters the airgun.

There is a seal where the CO2 cartridge buts up to the valve, this seal can be damaged or even deformed from usage or even leaving your CO2 in the gun for too long. The outside CO2 Valve seal can also take the shape of a specific CO2 nub so when you use a different brand CO2 the seal may not properly make concat with the new CO2 type you are using, again causing leaking or even the total loss of all your CO2. Watch my YouTube video on “How to Fix Leaking CO2 in an Airgun”.

CO2 Valve Related Problems:

Again, make sure that Outside CO2 Valve Seal is in good condition and any leaking is not being caused by this problem, if you have checked the Out Side Seal and everything is OK with it then perhaps there is a problem with the CO2 valve?

One indication that your CO2 Valve might be the culprit is the total loss of all your CO2 when you try to insert and tighten a new CO2 Cartridge. Usually all the CO2 will exit the barrel, not the handle or valve area. What may be happening is the valve is stuck open or the internal seal is broken or deformed. If this is the case you will have to remove the valve and have a look inside, this is a lot easier on CO2 airguns that have the CO2 valve in the magazine, if the CO2 valve is in the actual Airguns then a lot more disassembly may be required and I would recommend an Airgun technician take care of this for you.

If the gavel is in the magazine then you will have to unscrew it, you may require a special tool for this? Once the valve is out of the magazine  take a look inside and examine the internal seal, also look for any bits of metal shavings as they can disrupt the action of the valve causing leaking. Give the inside of the valve a good clean and then lubricate it with some silence spray. hopefully that fixes your problem!

BB’s getting Stuck in the Blowback Gas Tube:

I have actually made a dedicated video for this problem so I will put a link to it in the description of this video. The main reason people may have this problem is because we all like to rack that slide on our full blowback Airguns, but if you have a fully loaded magazine then each time you reach that slide without shooting the gun, you are inadvertently trying to load another BB into the breach area, the breach is only designed to hold one BB at a time so after a few racks of the slide the newly loaded have no place to go but into the Gas Tube where they can get stuck and cause having to the operation of your Full Blowback CO2 Airgun.

BB’s Rolling Out of the Barrel of Your CO2 Airgun:

This is not actually a fault of the gun but happens because of the way the gun is designed. This situation can happen with certain CO2 Airguns when the gun user pulls the trigger really slowly while the gun is point slightly in a downward position. What is actually happening is the first part of the trigger is made to draw a BB from the magazine into the breach of the gun. If the barrel of the gun does not have a rubber hop-up stopper in it then the BB is free to roll down the barrel and out of the gun. How do you fix this problem? Be more committed to your trigger pull and or shoot at a target that is not so low. Perhaps place your targets slightly higher than the gun so the barrel is not pointing down, especially if you like to take your time with the trigger :)

A Little Maintenance Can Go a Long Way!

Sometimes a good cleans is all you need to do to get things working as they should, again I have already made video Tutorial Showing “How to Clean Airguns and Blank Guns”.

What about stuff like My Airgun is jammed or my trigger is stuck or some random part fell out of my gun?

There is only so much I can cover in this video, most other problems are going to get a bit more complicated to fix and I suggest if your Airgun is not working and the suggestions I have made in this video do not solve your problem, then consider taking your gun into a gun tech.

First off I want to say it’s hard to trouble shoot technical or mechanical problems over the internet regardless of if ithas to do with guns, cars, computers or pretty much anything where unless you are there in person it’s really hard to figure out the problem.

But I will attempt to address some of the more common issues why a blank gun may not be functioning properly.

Why is my Semi Auto Blank Gun Not Cycling or Ejecting Shells?

One very common reason a blank gun may not be cycling the shells properly is because the owner has removed the barrel restrictor plug. People usually do this to make the barrel opening look more realistic but the barrel restrictor is a necessary component to increase the back pressure allowing the slide to cycle fully to the rear position so it can eject and pickup a new shell.

The blanks you are using may not have enough gun powder in them. Some blank guns require banks with more gun powder than others, again this additional internal pressure forces the slide all the way back, if the blank does not have enough gun powder in it then only a partial slide motion happens and so the discharged shell may not eject properly, in this case the user would have to clear the blank gun manually so another shell can then be picked up and loaded into the breach.

If your blank guns is dirty or not lubricated then it may act sluggish again restricting the full movement of the slide which will effect correct operation. Make sure to thoroughly clean and lubricate your blank gun, that may be a quick fix for you!

You may have a faulty extractor? The extractor is like a hook that grabs the discharged shell while the slide is in the reward position pulling or extracting the shell out of the breach. If the extractor is worn or broken then the empty shell will not be ejected from the breach so when a new shell is picked up from the magazine it has nowhere to go and usually you will get a jam-up in the ejection port area.

One final situation that can cause your blank gun to not cycle properly is to strong of a slide spring, some blank guns out of the box just come with a really heavy slide spring, so much so that even blanks with lots of gunpowder in them are still not strong enough to make the slide operate full motion. Your only option here would be to replace the heavy slide spring with a lighter one.

Why Are My Blanks Not Firing?

This is a situation where you pull the trigger and nothing happens. Lets get the obvious causes right out of the way here… Did you put blanks in your gun and are they new blanks? Did you chamber the first round in your semi auto pistol?

So now that that’s out of the way let’s look at some other reasons why your blank gun may not be firing a blank. Perhaps the firing pin is broken? Most blank guns are not made out of carbon steel and even the firing pins can be lesser quality than what you would find in a real gun so blank guns are more prone to breaking than real guns. I have seen broken firing pins in blank guns first hand so make sure to check the firing pin and that it is fully operational.

Try changing up your blanks to another brand? Again blank gun ammunition is not made to the same higher standards that real firearm ammo is made and some primers may require a little more pressure than your gun is providing. Even with real guns an ammo change may help the gun operate better.

Why is the Trigger or Hammer Not Operating Properly?

I have come across blank guns where there are mechanical problems in the trigger and hammer areas, you may be able to address this yourself but I would recommend taking your blank gun to a gunsmith since you will have to take the gun pretty much full apart to fix a problem in the trigger and hammer areas.

Of course make sure your gun is clean and lubricated, this can help a lot with the mechanical areas of your blank gun.

One problem I saw with a few EKOL Special 99’s was specifically with the single action potion of the trigger, when I would pull the hammer back it would not lock back and the hammer would often slip and fire randomly, this is rather dangerous. When I took the gun apart I found that the table top or step that the trigger was supposed to catch on was worn down on the edge so it would simply slip off. I was able to fix this by filing a new edge on the step area. Again this can happen because blank guns are not made out of as high quality metal materials as real guns.

Why does the Flame Come out the Top of My Blank Gun and Not the Front?

If you find that the flame or discharge comes out of the top of your blank gun and not the barrel, this usually does not mean anything is wrong with your blank gun. All it means is you own a top venting blank gun and not a front firing blank gun. In some countries front firing blank guns are not allowed but front venting blank guns are. The same may also be reversed in some countries, for instance here in Canada we can only import front firing blank guns with flare adaptors since our blank guns are imported under the assumption that they are to be used as signaling or flare devices.

Can I Convert my Top Venting Blank Gun into a Front Venting Blank Gun?

I really don't recommend altering a blank gun in any way as it may be a violation of your local laws and it could cause the blank gun to malfunction in a very bad way causing serious injury or even death!

In theory I suppose it may be possible to convert your Top Venting Blank Gun into a Front Venting Blank Gun but again you would need to allow for just the right amount of back pressure so a wide open barrel would not work unless it was a revolver. You can not simply remove the red plug and bingo you have a front firing blank gun because in most cases the barrel will be completely plugged in the frontal region. Not only would you need to drill out the plugged portion of the barrel but you would also have to somehow fill in the top venting area and again makes sure to allow for just enough back pressure to cycle the slide back and forth.

Hopefully this has helped some of you with blank gun issues. If you’re looking for a blank gun make sure to come down to www.ReplicaAirguns.ca and www.ReplicaAirguns.us and have a look in our blank gun area of our online stores.

Power Sources Covered in this review: CO2 - Green Gas / Propane - Spring - AEG / AEP (Automatic Electric Gun - Airsoft Electric Pistol)

Pro’s:

• CO2 Airsoft Guns allow for fast repeat shooting, great for action shooters, generally CO2 Airsoft Guns will have a little more power then Green Gas Airsoft Guns. There is no need to pump or cock your CO2 powered Airsoft gun in-between shots and a CO2 power source can allow for a very realistic action of the gun you are shooting. 

• Green Gas (Propane) Airsoft Guns operate much the same as CO2 Airsoft guns so they all make for great action shooters and the Green Gas powers the mechanical operation allowing for very realistic operation. Green Gas (Propane) Airsoft Guns can cost a little bit less to operate that a CO2 Airsoft Gun especially if you plan to use Propane as it can be cheaper to buy than the smaller 12 gram CO2 Cartridges.

• Spring Airsoft Guns are generally fairly basic and low cost so they are the usually the most affordable Airsoft guns to buy. There is no need to buy CO2 or Green Gas or even a Battery and Charger Setup so the cost to shoot Spring Airsoft Guns is only going to be subject to the Airsoft BB’s you plan on buying.

• AEG (Automatic Electric Guns) have the most consistent power as they use a spring internally that the electric motor draws back before each shot, the internal spring will essentially apply the same force to the Airsoft BB’s with each shot. AEG (Automatic Electric Guns) are a great option when you are wanting a Full Auto Airsoft gun since there is no cool down effect and as long as your batteries are charged and you have Airsoft BB’s in your magazine, the gun will simply keep shooting. AEG (Automatic Electric Guns) allow for the highest capacity magazines and often hold as many as 500 Airsoft BB’s in a single magazine. So if you’re looking for raw firepower an AEG or AEP Airsoft Gun is your best option. Once you have purchased your AEG (Automatic Electric Gun) and a battery and charger setup, they are fairly inexpensive to operate since no CO2 or Green Gas is required.

Con’s:

• CO2 Airsoft Guns require the additional cost to buy the CO2 cartridges as they will not function without it. CO2 Airsoft Guns have a limited power output and lose power as you shoot and use up the CO2. CO2 Airsoft Guns are effected by hot and cold temperatures and will have less power in colder temperatures and may not even work in super cold environments. CO2 Airsoft Guns will have a more conservative ammunition capacity since too high of a capacity magazine would freeze up the magazine and even the gun.  

• Again since Green Gas (Propane) Airsoft Guns work much like CO2 Airsoft Guns, they are effected by cool down and lose power when shoot quickly or as the Green Gas or Propane runs low. Green Gas does not expand as much as CO2 so it will not be as powerful and even less effective in colder temperatures. Green Gas Airsoft Guns will have a more conservative ammunition capacity since too high of a capacity magazine would freeze up.

• Spring Airsoft Guns are not the best action shooters since you need to manually operate the slide to pullback the spring prior to each shot, this does work well with Pump, Lever and Bolt Action Airsoft guns but is not the best option for pistols since most real steel pistols operate in semi auto mode.

• If you plan to use your AEG (Automatic Electric Gun) in a battle then it will require a multi battery setup which does cost a bit more upfront. AEG (Automatic Electric Guns) are know to not operate as realistically as a CO2 or Green Gas Airsoft gun since CO2 and Green Gas Guns do allow for the same realistic mechanical operation which can give very believable blowback operation, this is hard to replica with an AEG Airsoft Gun.

This is not to say that a “Real Gun” is not as good as an Airgun or better in other ways, in this video I’m just pointing out how an Airgun in some cases can actually be better suited than a Real Gun.

Availability: What I mean by this, is that in many countries Real Guns can be very hard to acquire and often require safety course and applications before one can purchase a Real Gun. I have no problem with this but it is a reality that must be considered. Having an Airgun versus not having a gun at all makes it a better option for people that live in countries that have strict gun laws. Here in Canada we are allowed Real Guns, even pistols but we do have restriction on our pistols and so I can only get certain guns in an Airgun version. As a collector this is better than not having the gun at all.

Price to Buy: Generally speaking you can pickup an enter level Airgun for much less money than a real gun.

Cost to Shoot: Real gun ammo prices have been steadily increasing to the point that a day out shooting can cost several hundred dollars just on the ammunition alone.

Comparison of Price:

• 50 rounds of 9mm ammo will cost around $18.00

• 6000 rounds of 4.5mm Steel BB will cost about $18.00

• CO2 is a bit less than $1 per 12 gram Cylinder which can yield up to 100 shots each.

• To shoot 100 rounds of 9mm will cost close to $40 versus 100 shots of 4.5mm steel BB at around $1.

• For this reason alone an Airgun can make a lot of sense even for Real Gun owners looking to get more cost effective practice time.

Access to Shooting Locations: Depending on where you live you will have to consider your local laws and where you are allowed to shoot both types of guns but typically you can shoot an Airgun safely just about anywhere as long as you implement some backstop safety precautions. Here in Canada we can only shoot a pistol at designated gun ranges, where as Airguns have a lot more allowances to shot them as long as you are not braking any city bylaws.

Training Guns: Even if you plan to eventually step up to a Real Gun at some point, an airgun is a great option to first learn proper gun handling skills since if you where to make a mistake, the consequences are much less severe. Airguns are also a lot less intimidating than a real gun since they are much quieter and have less recoil, you don’t even need to wear ear protection with most Airguns which means an instructor can communicate to his pupil on the range a lot easier.

Prop Guns: Since Replica Airguns look so much like real guns these day, they can often be used as a safer substitute for use in Movie, TV or other Photo and Video productions. Using a Real Gun on set generally requires a certified “Gun Wrangler” be on hand as Real Guns must be transported, stored and handled using very strict regulations. Airguns generally do not need to follow the same rigid regulations that Real Guns are bound to.

Tactical Training with Live Targets: Obviously shooting a real gun at a live target would not fair well for anyone involved, so that is completely out of the question. Airsoft Airguns are however perfect for Tactical Training and other weapons based simulations. All that is required for safety when using Airsoft guns is the use of eye protection and generally some heavy clothing.

I am sure there are some more areas in which Airguns may have the advantage over a Real Gun but these are the main ones that I could think of.

It has been a while since I picked out some of my favorite guns, after all my favorite gun picks change on a daily basis since there are so many awesome guns out there to pick from.

This Vimeo video is a little different since I pick out my favorites from a bunch of mostly replica gun categories including Steel BB, Pellet, Airsoft, Revolvers and Blank Pistols.

You may notice most of my picks happen to be blowback guns but to me airguns are all about being as realistic as possible and having blowback operation to me help to simulate the realism that much more. The exception in this video is in the pellet gun category since I decided on a pellet gun that was more about function and purpose over being any type of real replica.

Hopefully you take the time to watch my entire Vimeo video since I also bring out some close runner ups but here is a list of my top picks on this day, tomorrow it could be a completely different list of guns ;) 

• Steel BB - Umarex/KWC Smith & Wesson M&P 40 CO2 Blowback BB Pistol

• Pellet - Webley & Scott Tempest .22 Caliber Pellet (Spring Piston)

• Airsoft - KJWorks KP-11 1911 Hi-Capa 1911 CO2 Blowback Airsoft Pistol

• Blank - ROHM RG-88 9mm P.A.K. Blank Pistol

• Revolver - Dan Wesson 715 Revolver (BB, Airsoft, Pellet Versions)

Buy Umarex/KWC Smith & Wesson M&P 40 CO2 Blowback BB Pistol in Canada

BuyUmarex/KWC Smith & Wesson M&P 40 CO2 Blowback BB Pistol in the US

BuyWebley & Scott Tempest .22 Caliber Pellet (Spring Piston) in Canada

Buy KJWorks KP-11 1911 Hi-Capa 1911 CO2 Blowback Airsoft Pistol in Canada

Buy ROHM RG-88 9mm P.A.K. Blank Pistol in Canada

In this Field Test Shooting video I test out the KJWorks KP-11 Hi-Capa 1911 CO2 Blowback Airsoft Pistol to determine what the real work velocity is and also how well it performs in terms of accuracy. To test velocity I use a my Chrony Chronograph and do my best to get 5 good readings which I then average out. I always use a brand new 12 gram CO2 cartridge and generally use .20 gram plastic Airsoft BB's for my entire Field Testing. To test accuracy I set myself up 30 feet back using a semi rested position, to do this I place a sand bag to rest my hand and gun on and then stand securely in the back while I place 10 rounds on a paper target. There is obviously some humane factor involved but I can usually get a good idea on how accurate a given gun is.

During the Velocity or Feet Per Second Chronograph testing, I did manage to get 5 good readings, not all in a row but all within the first 10 or so shots. The KJWorks KP-11 Hi-Capa 1911 CO2 Blowback Airsoft Pistol shot hard and averaged 420fps again using .20 gram Airsoft BB's.

For my accuracy testing, all 10 shots placed within about 3 inches and they where fairly well centered left to right but did shoot a little bit high, this could be corrected using the hop-up adjustment to bring the Airsoft BB's down just a little.

I was rather surprised at how loud the KJWorks KP-11 Hi-Capa 1911 CO2 Blowback Airsoft Pistol is, it is by far one of the loudest CO2 Pistols I have shot to date other than the Umarex Desert Eagle Pellet Pistol. The KJWorks KP-11 Hi-Capa 1911 CO2 Blowback Airsoft Pistol also has a lot of blowback kick which makes it a lot of fun to shoot. Don't expect a lot of shots per CO2 since it uses a lot of CO2 per shot but in my books it is worth it for the added blowback recoil.

The KJWorks KP-11 Hi-Capa 1911 CO2 Blowback Airsoft Pistol may shoot a little bit hot for indoor Airsoft close quarters games but if you plan to use it outdoors at longer ranges it would definitely send Airsoft BB's out to further away targets. You could also pickup a Green Gas Magazine to lower the FPS about 50fps or so which would calm the KJWorks KP-11 down enough for indoor shooting.

Make sure to also checkout my full Table Top Video Review for more info on specifications and features for the KJWorks KP-11 Hi-Capa 1911 CO2 Blowback Airsoft Pistol.

Buy the KJWorks KP-11 1911 Airsoft Pistol in Canada

Type: Airsoft Gas Blowback Pistol.

Manufacturer: Cybergun - VFC.

Model: FN Herstal FNX45 Tactical

Materials: Metal and Polymer.

Weight: 2.09 pounds (950 grams).

Barrel: 4 inches, metal non-rifled.

Propulsion: GBB - Green Gas or Propane.

Action: Semi auto, single & double action with full blowback.

Ammunition Type: 6mm plastic Airsoft BB's.

Ammunition Capacity: 25 round full size drop out metal magazine.

FPS: 366+ with extended barrel.

Trigger Pull: The trigger pull on the VFC FN Herstal FNX45 Tactical GBB Airsoft Pistol is surprisingly light in single action mode, there is also minimal takeup. When shooting in double action the trigger pull length is much longer and heavier and has a bit of a stickiness too it but since this is a blowback pistol most of your shooting will be in single action mode where the trigger feels great!

Accuracy: I haven't done a dedicated Field Test Shooting Video yet for the VFC FN Herstal FNX45 Tactical GBB Airsoft Pistol but I did get the chance to play around with it when I did my I.C.U. 2.0 HD Action Camera review. In terms of power and accuracy it feels pretty good and you can expect to get decent power and accuracy out of it, we will have to wait and see how it performs on paper targets and when tested on the Chrony.

Build Quality: The VFC FN Herstal FNX45 Tactical GBB Airsoft Pistol is well made overall, I have found pretty much all the VFC airguns I have gotten my hands on seem to be well made and very realistic. you will find metal parts where they would be on the real Steel version of this pistol and same goes for plastic parts like the frame in this case. The finish seems to be holding up nicely too for me.

Realism: VFC really seams to pay a lot of attention to every detail of their Airsoft guns and the VFC FN Herstal FNX45 Tactical GBB Airsoft Pistol is no exception. All the mechanical working parts on this Airsoft version work as they would on the real .45 ACP FN Herstal FNX45, even the extractor is a separate part not moulded into the slide like you would find on most Airsoft pistols. You also get Interchangeable Back Straps to accommodate different hand sizes and of course it's fully FN licensed!

Purchase it from:The Replica Airguns Store

Pros:

• Excellent reproduction of the real steel FN Herstal FNX45 in looks and operation.

• Very Crisp Firm full blowback operation.

• Excellent fit and finish.

• Everything is Ambidextrous so great for lefties too.

• High Rise sighs suitable for the addition of a moc suppressor.

• Comes with two interchangeable internal barrel lengths.

• Fully field strip-able.

• Fully FN Herstal Licensed.

Cons:

• Comes with a red tip.

• Magazine is kind of shiny

• My serial number plate fell off while shooting it so make sure yours is on tight.

Comments:

Like I have mentioned throughout this review, VFC not only makes super realistic Airsoft guns, they also make a really high quality product. The VFC FN Herstal FNX45 Tactical GBB Airsoft Pistol is another example of this and offers everything you would hope to expect in an Airsoft Replica! The only down side is the orange tip  but that can be sorted out easy enough after you get it. It's definitely not a small gun so keep that in mind when deciding on buying it, overall the VFC FN Herstal FNX45 Tactical GBB Airsoft Pistol is a really nice Airsoft gun at a reasonable price point.

My Vimeo Video Review for the VFC FN Herstal FNX45 Tactical GBB Airsoft Pistol:

Buy the VFC FN Herstal FNX45 in Canada

Buy the VFC FN Herstal FNX45 in the US

Type: Blowback Airsoft Pistol.

Manufacturer:KJWORKS.

Model:KP-11 M1911 Hi-Capa

Materials: Metal slide with Polymer frame.

Weight: 2 pounds (930 grams).

Barrel: Metalnon-rifled smooth bore.

Propulsion: 12 gram CO2.

Action: Blowback, Single action only.

Ammunition Type: 6mm plastic Airsoft BB's.

Ammunition Capacity: 28 rounds.

FPS: 360+ fps.

Trigger Pull: The trigger pull on the KJWorks KP-11 1911 is very good since it is modeled after a real steel 1911 which makes it short and crisp with a nice light trigger pull. There is a very slight take-up at the very beginning of the pull but once your get past this the release is crisp and predictable. Since it is not a double action trigger you will need to either rack the slide for your first shot or pull the hammer back if you have already chambered a round.

Accuracy: I have not done my actual Field Test Shooting video review for the KJWorks KP-11 M1911 Airsoft Pistol so I do not have any definitive feedback for you but based on my experiences shooting other KJWorks 1911 styled Airsoft CO2 Pistols I expect it to have great blowback action recoil, a nice trigger and good overall FPS and accuracy. In terms of reliability, KJWorks pistols are solid in this department.

Build Quality: As expected, the KJWorks KP-11 Hi-Capa 1911 CO2 Blowback Airsoft Pistol build quality is exactly like all the other KJWorks Airsoft guns I've tested so far, Build quality for the price point is top notch with tolerances between the moving parts like the slide and frame are extremely tight showing excellent workmanship and machining from KJWorks. The finish is always a step above other similar styled Airsoft and BB guns, youn really don't have to worry about the finish coming of as easy.

Realism: The KJWorks CO2 KP-11 Hi-Capa 1911 Blowback Airsoft Pistol copies the real steel very popular even today Colt 1911 45 caliber pistol, it can be field stripped very similarly to a real 1911 Semi Auto pistol and all parts function virtually the same including a working safety, grip safety, slide catch-release, magazine release and hammer. This Hi-Capa version has a more tactical look with a wider frame for what would be a double stack hi capacity styled magazine.

Available in the:Replica Airguns Store

Pros:

• Has really good weight but not too heavy since it has a polymer frame..

• Expect to have typical KJWorks crisp and firm full blowback operation.

• Excellent fit and finish. I like the mat textured finish which looks to bed super durable.

• Nice bright white dot sights, really easy to see.

• I like the look of the tactical hammer and trigger.

• Nice high capacity magazine with a little extra zing for the CO2 Mag.

• Fully field strip-able.

Cons:

• Is not really setup up for left handers with no real ambidextrous components.

• CO2 magazine is long to accommodate the 12 gram CO2.

• Grips may be a bit thick for smaller hands.

Comments:

I love 1911 pistols and enjoy shooting them, there is something about how they feel in the hand that is different form most other pistols. They always feel so solid. The KJWorks Airsoft versions capture that feeling exactly and again the little bit more you may pay for a KJWorks 1911 over some other lesser quality Full blowback 1911's is worth the cost in my books. This Hi-Capa 1911 version with it's tactical look and finish would make a great game player for sure!

My Vimeo Table Top Review of the KJWorks KP-11 Hi-Capa 1911 CO2 Blowback Airsoft Pistol:

Buy the KJWorks KP-11 1911 Airsoft Pistol in Canada

Recently I picked up my new Chrony Beta Shooting Chronograph to replace my F-1 that has not been working so well for me in past videos... I wanted to get outside and give it a try shooting a few of the airguns that I was not able to test out properly. Now I know that under my patio deck, the lighting is not optimal even on sunny days and because of this I have never expected to get perfectly consistent fps recording but as many of you know, my old Chrony F-1 was pretty much not working at all near the end there.

I have ordered a light kit which will help out a lot especially when summer is over and the sky becomes more overcast. But for now I decided to test my Chrony Beta Chronograph under my deck roof as I have been testing all along and see if I can get better results with this newer Beta version.

So makes sure to watch my Vimeo video testing of my Chrony Beta Shooting Chronograph shooting a selection of airguns.

Type: Blank front firing pistol.

Manufacturer: SM.

Model: Mod 110 8mm.

Materials: Mostly metal with plastic grips.

Weight: 11.75 Ounces (332 grams) Unloaded.

Barrel: Front firing.

Propulsion: Gun powder.

Action: Semi auto, single action only

Ammunition Type: 8mm P.A.K. blanks.

Ammunition Capacity: 5 rounds.

FPS: NA.

Trigger Pull: The trigger on the SM Mod 110 8mm Blank Pistol is single action only so you will need to rack the slide to not only chamber a round but also cock the internal hammer / striker, follow up shots will case the slide to cycle on it own allowing for single action shooting. The trigger is rather nice with just a slight bit of take-up followed by a light release.

Accuracy: NA.

Build Quality: The SM Mod 110 8mm Blank Pistol was made in West Germany sometime back in the Mid 70's so this pistol is 30-40 years old and still looks great. Mine does have some slight pitting on the right side I am assuming from sitting in the box up against the manual which more than likely may have an acidic property to it. Even so this pitting is minor and the gun is in good condition overall. Like most blank pistols much of the gun is made out of pot metal (a zinc alloy) but it does have hardened steel parts where they need to be (Barrel, ejector, hammer, pins, screws and magazine).

Realism: The SM Mod 110 8mm Blank Pistol is not a true replica as far as I can tell is not an actual replica of any real steel semi-auto pistol in production but it does look a bit like the American Derringer LM5. In terms of looking like a gun it looks like what you would expect a small caliber sub compact pistol should look like and all operation is exactly like a semi auto pistol with the exception that the SM Mod 110 only shoots blanks since the barrel is obstructed with a metal rod.

ROHM Guns Available in the: Canada Replica Airguns Store

Pros:

• German made with high quality materials.

• Very small and compact.

• Front firing.

• Nice light and short single action trigger. 

Cons:

• Hard to find one in North America.

• Only holds 5 rounds.

• Slide does not stay back when empty.

Comments:

I really like unique blank guns since they are so hard to locate here in Canada. When I saw this sitting on the table at my local gun show I kind of wondered if someone had accidentally left out a prohibited firearm but once I inspected it I quickly realized it was a blank shooter and decided right there and then I had to have it. I did pay close to $200 for it but to me it is worth it simply because this little blank shooter is a rare find and it was also in really good condition and even came with the original 8mm self defence pepper blanks. The SM Mod 110 8mm Blank Pistol is for sure a blank shooter I will be holding onto for some time...

My Vimeo Table Top Review for the SM Mod 110 8mm Blank Pistol:

Buy ROHM Blank Guns in Canada