We recently received some new pistols from KJWorks, The CO2 versions in Full Metal of the Colt 1911, the Berretta M9 and the Berretta M9A1. All of these guns are really well made, the fit and finish is excellent. Definitely a very high quality Airsoft pistol and worth spending a little bit more to get this extra quality. We have even lowered the price on many of our new KJWorks guns to make them even more affordable so check them out in our Canada Replica Airguns Store!
So I made a quick demo preview video where I get away from my table top and go outside to show them off a bit and shoot a few rounds through them at some clay pigeons. I did have some camera issues but you will get a good idea on how these guns look and perform.
My main goal in this Shooting Performance Test was to see how the ANT Advanced Novelty Tech CO2 HPAConversion Kit performed side by side with a standard 12 gram CO2. Keep in mind that you can also switch over at any time to a regular 12 gram CO2 even after installing the ANT adaptor system in the gun or magazine.
My choice of Airgun for this test was the KWC - Cybergun Mini UZIConverted to Full Auto. I chose this Blowback 4.5mm CO2 BB Gun because it uses a lot of CO2 with each shot and when shooting in full auto it literally eats CO2. I knew this airguns would really put the ANT Advanced Novelty Tech CO2 HPA Conversion Kit to the test.
My first performance test was to comparing both systems using a Chronograph so I could see how the fps velocity slowed down because of the CO2 cool down effect. The 12 gram CO2 did pretty well emptying a full 25 round magazine but keep in mind I was shooting in semi auto only for the sake of using a Chronograph. I did notice a drop in velocity from a high of over 300 fps to a low of around 260. When I switched over to the Bulk CO2 ANT System and performed the same test the fps started out a bit lower but stayed pretty much about the same with a few ups and downs. The initial lower fps may have been a result of using separate magazines for each test since the valves in each magazine are most likely tuned a bit differently to let out more or less CO2 with each shot.
My second and most impressive test was to empty a full 25 round magazine in full auto mode! Again a started out using the standard 12 gram CO2 and to make this a real world test, I did not replace the 12 gram CO2 form the previous test. I figured 50 shots was a realist amount of shots to get from a single 12 gram CO2 and after all I was only shooting in semi auto which uses a lot less CO2 then shooting in full auto.
My KWC Blowback Mini UZI rocked pretty good using the 12 gram CO2 until it hit about a third the way through the magazine and then it stated to slow down and pretty much stop dead in its tracks with about 5-6 rounds still left in the magazine. The CO2 was all gone and I was left a bit unsatisfied :(
Without any significant break time to let my KWC Mini UZI warm up again, I switched over to the ANT Advanced Novelty Tech CO2 HPA Conversion Kit magazine and unloaded the full magazine in no time with no cycle rate slow down at all, even after the magazine was deprived of Steel BB's I kept squeezing the trigger and letting the blowback hammer my shoulder for several more satisfying bursts. Now that is what you expect from a full auto Blowback BB Machine gun!
In conclusion, when shooting in semi auto you will see better fps consistency using the ANT Advanced Novelty Tech CO2 HPA Conversion Kit but where this system really shines at least for me is I can shoot as fast as as long as I want and it will feel same as the very first shoot I take even when using a full auto system. No more switching out 12 gram CO2 every few magazines, just speed load some more BB's in and your good to go.
I was sent a really cool new product form a company called ANT (Advanced Novelty Tech). Their CO2/HPA Converter allows you to hook up either a large CO2 tank or High Pressure Air system using standard Paintball hose system.
What's kind of neat with the Advanced Novelty Tech CO2 HPA Conversion Kit, is that you can still interchange your 12 gram CO2 if you want to even after modifying your gun to use Bulk CO2 or HPA!
The ANT Advanced Novelty Tech CO2 HPA Conversion Kit works with well over 100 BB, Pellet and Airsoft guns most of which would be Pistols but some rifles are included in this list.
The main advantages over using standard 12 gram CO2 cartridges would be a significant lower cost for CO2, along with less fps velocity fall off, so better performance overall.
Stay posted as I will be making a field test performance test using the ANT Advanced Novelty Tech CO2 HPA Conversion Kit with my KWC Mini UZI Full Auto BB Machine gun :)
First off let’s get one thing straight! What I’m looking for in a BB gun is more than likely going to be way different than what someone else is looking for in what they think is the “Best BB Gun” available.
Many people will determine the Best BB Gun as the BB gun that has the highest price tag, usually you get better quality the higher the price goes up but not always, there are times when perhaps you are paying for a name brand or cosmetic add ons that don’t always make the gun better or the best.
On the other hand, some people will determine the best BB gun as the one that is the least cost since they may not have a lot of money to spend, and an expensive BB gun is a BB gun that that person would not be able to afford or even own, far from an ideal or the Best BB Gun for them.
Many people only look at the specifications to determine if that particular BB gun is the outright best BB Gun. One specification that people seem to fixate on is how powerful is the BB gun in question? If it has the highest FPS then surely it must be the best BB Gun! That Pop can never saw it coming! What about cost of operation, so things like reliability and how many shots per CO2 you can get out of a BB gun. All important features to consider when picking out the Best BB Gun!
Style is another important part of what makes a BB Gun the Best option for you, are you wanting a classic BB Pistol? Perhaps a Modern BB Gun, Maybe even a BB gun that you can not get in your area because of gun laws? Style is a very individual preference and what looks good to me may look terrible to someone else.
One aspect that is very important to me, is realism, does the BB Gun operate the same and does it have similar metal and plastic parts as the real steel version? Does the BB gun I am considering have blowback operation and a true single or double action trigger like it’s big brother? What about a full size drop out magazine and the ability to field strip the BB Gun?
Some people want their BB gun for simple backyard good old fun shooting and so as long as it shoots pretty straight and works as it’s supposed to, then that is all they care about. Many real steel shooters want a BB Gun to operate exactly like their real steel version, so they can practice with it to get in more trigger time when going to a gun range is not an option.
Of course there are aspects like Reliability, Performance, Fit and Finish, Licensing and Build Quality that all determine what makes the Best BB Gun and again it really depends which of these qualities are most important to you that will determine which BB Gun is the best BB Gun.
So how do you determine which is the Best BB Gun? Make a list of what you are looking for in a BB Gun. Attributes like Cost, Performance, Build Quality, Style, Realism, Availability…
Once you have narrowed down your Best BB Gun list, get as much information on each BB Gun you are considering, to narrow the list down even more. There are tons of Youtube videos you can watch for your Best BB Gun final short list to help you determine your ultimate choice.
So please don’t ask me what the Best BB Gun is? I can not even tell you which one I like the best since my wish list changes from day to day…
Trigger Pull: The trigger pull on the Gletcher NGT Silver CO2 BB Revolver is nice and crisp in both single and double action, there is virtually no trigger wiggle and the trigger pull is decent in double action while much longer and of course nice and light in single action as expected. You will want to pre-cock the hammer for accurate single action shooting but have the option of shooting double action for any action shooting you may want to do. Keep in mind you will have to individually reload each round.
Accuracy: I have not done any shooting so far with this Gletcher revolver due to some pretty awful weather conditions. I expect it will shoot nice since it has a fairly long sight radius and the open iron sights are conducive to precise shooting.
Build Quality: The Gletcher NGT Silver CO2 BB Revolver is really well made, you can tell by it's solid weight for a fairly small pistol, all of the mechanical parts feel smooth and responsive. Everything that would be metal on the real M1895 Revolver is metal including the solid one piece cylinder. Yes the grips are imitation wood but this is to be expected. The sliver finish looks great and I like the black contrasting parts that really highlight this gun.
Realism: I've have not had the opportunity to actually put my hands on a real steel Nagant M1895 Revolver but from the photos I have viewed online, the Gletcher NGT Silver is very accurate in terms of being a BB replica. Of course the shells fit steel BB's internally and the barrel has been downscale to shoot 4.5mm Steel BB's but other than that it is very difficult to tell it from a real Nagant M1895 Revolver. Even the barrel opening is recessed and looks true to scale for the original rounds used in this revolver and you can remove the one piece cylinder similar to the real version.
Pros:
Beautiful Silver finish.
Very solid and weighty gun.
Hammer and trigger actions are very crisp, virtually no wiggle.
CO2 is well hidden.
Recessed barrel looks great.
7 round cylinder instead of 6 like the other shell loading.
Cylinder can be removed.
Shoots in both signal and double action.
Grip is nice and small so great for shooters with small.
Shooting performance pros yet to be determined…
Cons:
Non adjustable sights. (Perhaps like original)
No speed loading on this one, one shell at a time, so make your shots count.
Shooting performance cons yet to be determined…
Comments:
The Gletcher NGT Silver CO2 BB Revolver is yet another addition of shell loading revolvers like the Dan Wesson and KWC 357 based revolvers, with the exception that the Gletcher NGT is more of a blast from the past and even though it comes in at a much more compact size, it holds an additional round! Another note worthy point is the fact that Gletcher has somehow figured out a way to reduce the CO2 release valve giving the Gletcher NGT a more true to scale frame size, I am talking about the distance between the hammer and the cylinder. This allows for a more realistic and true to dimension replica which in this classic revolver is super important.
My Vimeo Table Top Video of the Gletcher NGT Silver CO2 BB Revolver:
Make sure to also checkout my full Table Top Review where you will find more details and specifications for the KWC Luger P-08 Airsoft replica pistol which is virtually the same gun as the 4.5mm BB version with the only real difference being the ammo type and the amount of rounds per magazine (21 rounds for the 4.5mm BB version and 15 rounds for the 6mm Airsoft version).
Basically in this YouTube video, I shoot the 4.5mm Steel BB version of the KWC P-08 Luger head to head against the Airsoft Version to see how they compare in terms of Feet Per Second speed and Accuracy from30 feet away from a paper target using a semi rested shooting stance. As expected the heavier 4.5mm Steel BB's shot a bit slower but did seem to have a slight advantage in the accuracy department.
Watch my YouTube Field Test Head to Head Shooting video of the KWC Luger P-08 CO2 Blowback Replica Pistols to see how they both compared:
This topic of Blowback Airguns Versus Non-blowback Airguns comes up often so I thought I would address it a second time around since I get a lot of new visitors and subscribers daily who may not have watched my first video explanation on this topic. You can also checkout my first video on this subject since there may be some stuff I missed out in this video second video ;)
There are really two types of people asking or commenting on Blowback Airguns Versus Non-blowback Airguns. The first type of person who genuinely wants to know which is best and for what reasons. Then there is the other kind of person who makes a narrow minded statement that one type is clearly better than the other type, based on their own preferences and interests but not considering that there are other people out there with different opinions and preferences than them. You know who you are and we all know you are not going to change cause that would require an open mind...
Here is a list of the Pros and Cons I go over for each style of Airgun:
Pros:
Blowback guns simulate recoil.
Blowback guns can have better and more true triggers compared to their real steel counterparts.
Blowback guns can be better suited for action shooting.
Blowback guns are better as prop guns.
Blowback guns are generally more realistic in terms of mechanics.
Non-blowback guns generally use less CO2 per shot.
Non-blowback guns generally have higher fps.
Non-blowback guns can be more accurate.
Non-blowback guns can be more reliable.
Non-blowback guns can be less expensive.
Cons:
Blowback guns generally get less shots per CO2.
Blowback guns generally have lower fps.
Blowback guns can be less accurate.
Blowback guns can be less reliable.
Blowback guns can be more costly.
Non-blowback guns do not simulate recoil.
Non-blowback guns do not have true single action only triggers.
Non-blowback guns generally have heavier triggers that slow down shooting performance.
Non-blowback guns are generally not as good for prop use and or training.
Non-blowback guns generally are not as realistic compared to their real steel counterparts.
Watch my Vimeo video where I go into detail on Blowback Airguns Versus Non-blowback Airguns again ;)
In this Vimeo video, I go over a common question I get pertaining to the recoil effect of Airguns and Blank Guns. Many people want to know if Airguns and Blank Guns have similar recoil effects to a Real Guns and if so, how much recoil will you feel from an Airgun or Blank Gun?
The short answer is yes, there is some recoil with both Airguns and Blank Guns since whenever there is a force in one direction there will be a somewhat similar force in the opposite direction creating what we feel as recoil. With Airguns since the force from the CO2 or compressed air is rather small in comparison to that of the gun powder blast from a Real Guns or even a Blank Gun, the recoil is very slight. Blank Guns have similar gun powder charges to a Real Gun and so the recoil is more noticeable but unlike a Real Gun, a Blank Gun does not really push against a sizable object like a bullet, a Blank Gun only pushes against the air in front of the barrel which has very limited resistance and so there will be much less felt recoil from a Blank Gun than the recoil from a Real Gun pushing on a heavy grain bullet.
With semi auto Guns like Blowback Pellet and BB Guns and semi auto Blank Guns, there is also the momentum and mass of the slide to consider as it moves backwards and forwards which also gives the effect of recoil and in the case of an Airgun accounts for most of the recoil felt by the shooter.
Watch my Vimeo video on this subject where I go into much more detail and explain the effect of recoil when shooting Airguns and Blank Guns:
In this Comparison video I go through the benefits and shortcomings of both Blowback and Non-Blowback Airguns. I focus mainly on Airguns but there is a definite crossover with Airsoft guns.
Here are some basic statements that best describe both Blowback and Non-Blowback Airguns.
Blowback Airguns:
Blowback Airguns usually have a movable slide that moves back and forth with each shot.
Sometimes the blowback operation is internal (Internal bolt) so there may not be an external moveable slide.
Some CO2 is used to move the slide rearwards in a Blowback Airgun.
The Blowback motion of the slide with some blowback airguns can also cock the hammer or internal striker allowing for true single action trigger pull. But not always!
Some Blowback airguns have the potential for full auto capabilities since they can have a true semi auto action.
There is some noticeable recoil from the Blowback action simulating the recoil of a real gun.
Non-Blowback Airguns:
Non-Blowback Airguns can have fixed or movable slides but they will not cycle back and forth with each shot.
Non-Blowback Airguns tend to have less working parts since no Blowback valves are required or even a moveable slide.
There are some Blowback and Non-Blowback Airguns that field strip similarly to their real steel counterparts but this is most commonly found in Blowback Airguns.
Non-Blowback Airguns require the shooter to cock the hammer for single action shooting or use a double action trigger pull for semi auto like performance.
Pros:
Blowback Airguns:
Blowback Action causes a noticeable recoil which makes the airgun feel more realistic.
Blowback Airguns in some cases have true semi auto action with true single action triggers which mimic the authenticity of the real steel versions of the guns they replicate much better making them better training tools.
Having some recoil makes blowback Airguns potentially better training tools.
Blowback Airguns look really cool when shooting them and are great action prop guns.
Non-Blowback Airguns:
Non-Blowback Airguns tend to have less working parts so less to go wrong and more reliability.
Non-Blowback Airguns can be more accurate since the recoil from the blowback is not a factor.
Non-Blowback Airguns have more potential power and more shots per CO2 since no CO2 is robbed for the blowback operation.
Cons:
Blowback Airguns:
Blowback operation can rob some of the power and will also rob how many shots you get from the Airgun.
Blowback Airguns are effected even more by cold weather and the cool down effect.
The recoil from Blowback Airguns can effect accuracy for some shooters.
Non-Blowback Airguns:
Non-Blowback airguns are generally double action when shooting semi auto and so the trigger pull will be longer and heavier.
Non-Blowback Airguns do not replicate the recoil action of a real gun.
Non-Blowback Airguns do not look as cool to shoot and are not as good of an action prop gun.
I stopped by the ICS Booth, we don't sell too much of their products but have carried a few items from time to time. ICS caries some nice quality Airsoft guns including the M1 Grand with real wood stock, and some AK & AR variants.
One of our suppliers had the new FN Herstal Five-seveN Blowback Airsoft pistol, I believe made by Marushin. Like the real FN Herstal Five-seveN, the pistol is pretty much all polymer including the slide and frame. This pistol also uses CO2 in the full size drop out magazine which should make it fairly powerful.
Looks like there is another Dan Wesson contender available now in the form of a Swiss Arms S&W 357 Magnum 4 inch and 6 inch barreled version, they look really nice and like the Dan Wesson have the realistic reusable brass shells that hold the 4.5mm Steel BB's.
Ever considered owning a mobile Gunsmith vehicle, look no further, I came across this pimped out Firearms Van complete with machine guns mounted in the front :) Inside was a complete firearms workshop.
Last but not least, we had some fun while in Vegas. I go down for the SHOT Show for business but I also bring my wife and we make time for some non business related activities. I generally stay at the WorldMark resort each time and this year the weather was pretty nice so we where able to get some sun by the pool a couple of days and I even got a tan line! Of course the food and entertainment is always awesome in Vegas.
We carry a lot of the G&G line and perhaps have as much in stock as you would find at the G& G booth ;) I did see a few items we do not have in stock so I will have to see what I can do about that. Some products that I hope to see added to our Canada Replica Airguns Store would for sure be the M1 Grand and our Canadian Military Colt C7A1/2.
One company I took notice of was Inokatsu, they make super high quality Airsoft guns. I was drawn to their Sig Sauer P229 and 1911 pistols that by the way are made out of real steel and as close to the real version as possible without it being a real gun. The Inokatsu pistols I looked at are not cheap and will set you back over a grand but are as close as you can get to a real sidearm as possible in an Airsoft version. They feel amazing to shoot with heavy blowback and that sound real steel makes when the slide snaps back.
Let me know if you're like me and would be willing to part with a substantial amount of money for one of these treasures?
So it's 2014 but I still needed to make my 2013 Airgun, Airsoft Gun and Blank Gun Collection Favorites for 2013. It's become a tradition I guess you could say. No I do not show all the guns in my collection but I do cover most of my favorites and also some new guns I picked up in 2013.
Here's a peek but make sure to watch the YouTube video bellow where I go over all my top picks for 2013. You can also buy many of the guns I show in this YouTube video over in our Canada and US Replica Airguns Store!
Trigger Pull: The trigger pull on the KSC M11A1 GBB Airsoft Machine Pistol is pretty much exactly what you would expect from this fast firing single action only semi and full auto machine pistol, it has a really short take-up and then a nice crisp light trigger pull. Since it is an open bolt system, you will need to pull back the bolt for the first shot, releasing the trigger releases the bolt, just like with a real M11A1.
Accuracy: At this point because I received this gun from another collector in used condition, it is not working 100%, the hop-up bucking was damaged and the new ones I ordered are not the correct versions for this Airsoft gun. It does shoot but it is temperamental, sometimes the bolt will not cycle all the way and I have no idea how this is effecting the fps and accuracy. It would not be fair to test it in this condition, hopefully I can find the right hop-up bucking for it and do the Field Test Shooting Review at some point.
Build Quality: MyKSC M11A1 GBB Airsoft Machine Pistol has been used a fair bit so it is somewhat battle scarred, still it looks pretty good and other than the Hop-up bucking problem I am having it should be in working condition, unfortunately without the correct hop-up bucking, this gun will not work properly. Hopefully I can find a hop-up bucking? Even though much of this machine pistol is plastic externally, it has held up very well, the metal parts do also help to balance it off and give it a decent overall 3 pound weight which feels good considering it is such a small gun.
Realism: The KSC M11A1 GBB Airsoft Machine Pistol is a very close copy of the real steel Cobra M11A1 Machine Pistol, all the parts appear to function just like the original Cobra RPB Industries M11A1 and it even field strips in the same manor. The full licensing and trademarks also help to make this replica very believable.
Very realistic and accurate replica with full Cobra RPB Industries licensing.
Even though there is lots of external polymer, it still has good weight to it.
Full metal 40 round drop out magazine, holds BB's and Gas.
Everything works like the original, field strips and lots of mechanical parts.
Shoots in both semi and full auto.
Cons:
Hard to get here in Canada and hard to get parts here in Canada.
Mostly plastic main build - Limited usage of metal and steel.
Have no idea how it will perform because it is not functioning at 100%.
Comments:
Well I've pretty much said everything I can say without actually shooting it? Even though my used KSC M11A1 GBB Airsoft Machine Pistol is not in 100% working condition, I still like having it as I like the replica aspects of owning it, how else would I get my hands on a .380 caliber full auto machine pistol here in Canada ;) And you never know, I may just luck out and find the proper hop-up bucking for it and then have the chance to do my Field Test Shooting Review for you all :)
My Vimeo Table Top Review of the KSC M11A1 GBB Airsoft Machine Pistol:
Trigger Pull: The trigger pull on the G&G AR styled Airsoft CM16 Raider is very smooth, the CM16 Raider uses a mechanical trigger that once the charging handle has been pulled back or "charged", works in a single action only manor with a slight bit of take-up and then a light predictable release. Each time the closed bolt gas blowback system shoots a round in semi or full auto, the internal action is ready for the next single action shot.
Accuracy: So far I have not tested Version 2 of the G&G CM16 Raider, but I have tested Version 1 so here are the result I got with Version 1 until I do my official Field Shooting Test with Version 2. When shooting from a 30 foot distance I did get some nice closely grouped shots from the G&G CM16 Raider Gas Blowback but when shooting in full auto it did spread apart somewhat, maybe from the GBB recoil? Version1 of the G&G CM16 Raider GBB shot an average of just over the 325 fps, I was using .25 gram BB's and it was a cool day so you can expect higher fps out of the G&G CM16 Raider when conditions are better.
Build Quality: The G&G CM16 Raider GBB being built on G&G Combat Machine Platform is targeted more for the price conscience person. The quality is consistent and good and I did not mind having more plastic in the G&G CM16 Raider GBB as my plan from the beginning was to add a lot of extra accessories and starting out with a somewhat lighter footprint made the gun still relatively usable even when all geared up with extra accessories. I also feel the plastic or polymer fiber upper and lower receiver and RIS rail system will also wear better than steel as it is more likely to flex rather than break in many situations, not to mention metal will show scratches and wear more over time.
Realism: Airsoft AR rifles in my opinion are very realistic in general, even the AEG versions work just like the real steel AR's with working charging handles, dust covers, bolts, magazine, adjustable stocks and sights, but I would have to give the advantage to the gas Blowback systems like the G&G CM16 Raider GBB as it has a full internal bolt with some decent recoil, it can also be field striped very similarly to a real AR15 rifle. The shot count is more like what you would find in an M16 or AR rifle which means you will need to consider ammo shot assuage and reloading more carefully when using it in an Airsoft game.
Super affordable Gas Blowback Airsoft AR M16 styled Rifle.
Very high rate of fire in full auto.
Polymer shell is both light and very durable, does not show scratches or wear as easily as metal.
All most every part is operational - Fully Ambidextrous now.
Can be fully customized, lots of mounting points on the RIS Rail system.
Fully adjustable Crane Stock.
Removable rear Iron Sight can be swapped out for other sighting systems and hardware.
Version 2 is a significant upgrade from Version 1.
Internals can be swapped over to make it an AEG gun.
Cons:
Some people may not like the polymer RIS rails and upper and lower receiver?
Would have liked to have seen some sort of a plate over the pistol grip to finish it off.
Comments:
I already really liked Version 1 of the G&G CM16 Raider GBB Airsoft AR Rifle and even bought a bunch of magazines and gear to sport mine up for use in some local Airsoft games, the upgrades and improvements found in Version 2 are the icing on the cake! I am hoping the internal performance enhancements will increase the FPS just a bit and Gas efficiency somewhat over Version 2 but will find out when I give it a thorough testing shortly. If you have been a bit scared off by the higher prices of some GBB Gas Blowback Airsoft rifles then perhaps take a look at the G&G Combat Machine Platform CM16 Raider in GBB, it may just change your mind about Gas Blowback Airsoft rifles!
My Vimeo Video Review for the G&G CM16 Raider Airsoft GBB AR Styled Airsoft Rifles:
Every so often I come across some interesting guns that people are willing to trade or sell me, if the price is right or the trade involves a gun I can part with, then I go for it and hopefully end up with something I may not be able to get new or that for me is hard to acquire in Canada.
My most recent trade added two new guns to the collection, a KSC M11A1 Airsoft Machine Pistol and a Daisy Power Line 2003 .177 Caliber Pellet Pistol.
Both of these guns are very hard to get since the KWC Airsoft M11A1 shoots a bit too week for import into Canada, and the Daisy 2003 is no longer in production.
The KSC M11A1 is a 6mm Airsoft pistol that shoots in both semi and full auto using a Gas Blowback open bolt system, it is a replica of the .380 Caliber Cobra RPB Industries M11-A1. Mine came with a mock suppressor and 7 magazines, although not all of them are in working condition. The KSC M11A1 is in working condition but needs a new Hop-up Rubber Bucking which I have on order.
The Daisy Power Line 2003 seems to be in really good condition but still needs to be tested, it is one of the only true blowback semi auto pellet pistols I know of, what I mean by this, is it has a true blowback system with a true single action trigger which means it can be converted to full auto which is one of the reason Daisy may have discontinued it. The Daisy Power Line 2003 uses a very interesting 35 round rotational magazine. Some say it is loosely styled after a Browning High Power pistol.
Stay posted for reviews on both of these pistols down the road.
You may wonder why I am doing another video on the G&G CM16 Raider Gas Blowback Airsoft AR Rifle? That's because the one I have here in this Update Video is Version 2 and yes there is a difference. So far I can only tell you about the obvious stuff since I really have not tested it out to see if there are any other performance gains with Version 2 over Version 1.
G&G has made some improvement with Version 2 enhancing several areas:
First off, there is now a selector switch on both sides of the receiver allowing for left or right handed use.
Carrying on with the ambidextrous theme, G&G also added a magazine release to the left side of the receiver.
Another missing feature was a bolt lock out when your magazine was empty, this has been added and so the bolt will lock back about 1/3 the way back locking out the gun and letting you know when you are out of ammo.
The bolt release on Version 1 was just for show and did not function. On Version 2, with the bolt lock, G&G also added a working bolt release.
Those are some pretty significant improvements to the G&G Armament CM16 Raider GBB Version 2 in my books! So now it's time to test it out and see if full auto mode has been improved. I found with Version 1, that when using full auto, the G&G CM16 Raider GBB would have some trouble getting through a full mag dump but when shooting very quickly in semi auto had no problems at all.
