In this "head to head to head" pistol shootout I compare three of my more powerful, or you could say effective air pistols against each other. Shooting at some pop cans from about 30 feet away to see how destructive each one is. I don't generally recommend air pistols for pest control simply because they tend to be less accurate and powerful than rifles, especially out at the longer ranges where a magnified scope is required and notably where the pesky vermin like to hang out.

I would have to say out of the three tested in this video comparison, the Webley Alecto in .22 caliber and the Modified Drozd Full Auto BB Gun would for sure get the job done at closer ranges. The Webley Alecto simply because it can hurl a heavy grain .22 caliber lead pellet right around the 500 fps mark which will take down small pests, again at close ranges.

My second choice or even first choice depending on how active the pest are would be my modified full auto 1200 rounds per minute Drozd that hurls 4.5mm Steel BB's at over 500 fps (under 4.2 foot pounds) at a rate of 20 BB's per second! A 4.5mm Steel BB traveling at 500 fps will penetrate fur and feathers very well and with most of the 20 BB's hitting a target in a matter of 1 second, that is going to humanly put a small to even medium sized pest down for sure. And yes the Drozd becomes a pistol when yuo take the rear stock off ;)

My last choice for the job is the Xisico XSP180 in .177 caliber since like the Webley Alecto it is only a single shot, so you got to make it count and being that it has less overall energy than the Webley Alecto again I would prefer the Alecto over the XSP180.

Watch my "head to head to head" Vimeo video to see how these three pellet pistols compare:

A very common occurrence with CO2 Airguns and Airsoft guns are leaky CO2 seals. Usually this occurs right where the CO2 cartridge connects to the main valve area. This can be either in the gun or in the magazine depending on the setup of the airgun.

There are many reasons why this can happen, but the most common reasons are a worn-out or dried up seals or even a seal that has been imprinted or misshapen from the constant pressure of the tip of the CO2 pressing against it.

When this happens you may encounter a leaking CO2, the severity of the leak can vary from mild slow leaks to leaks that can be so bad that the gun is unusable. Keep in mind there can be other problems not related to the CO2 seal such as in the valve area, the fix I show you in this YouTube video will not fix a leaking valve, you can try using something like Crosman Pellgun oil for a problem like that.

Watch my below Vimeo video where I show you how you can easily use some Plumbers Teflon Tape to improve the contact points between your CO2 and CO2 main seal and eliminate leaking CO2 in your Airgun.

A very common question I get asked is "How Long Can I Leave CO2 in My Airgun?" So what do I do when I get asked a question over and over again... Well I make a video and give you my answer to the question.

Some CO2 Related Questions I seem to get over and over again are:

1. Can I leave an unused CO2 in my Airgun and for how long is it safe?

2. Can I reuse a C2 once it is empty?

3. Can I use my gun without CO2?

In this YouTube video I address questions 1 and 2, I kind of forgot about question number 3 since it is not as often but it does come up from time to time believe it or not and the answer to being able to use a CO2 airgunwith out CO2 is "NO", It's kind of like trying to drive a car without gas, or turn on a light without electricity or stay alive without food...

So anyways, watch my below Vimeo video for answers to questions one and two:

This may be a bit controversial for some people who don't like the thought of using an gun for hunting or extermination of unwanted pests. But weather or not it is accepted by all, it is a practice that many people still embrace including myself when done in a humane way.

Let's start off by addressing this topic by asking some questions and filling in some of the answers. Keep in mind I go into much more detail in my Vimeo video below.

What is the reason that you need to Shoot or Hunt an Animal?

Are you shooting an animal out of need or just for fun, sure there is a thrill in the sport of hunting but after taking down your prey, the animal should not be killed in vain as the meat should be eaten. There are also times when pesky critters get into your gardens, tree farms, feeding stations garbages and who knows what else? I personally think shooting an animal that has not done you any harm or that you don't plan on eating is not ethical. So question your motives wisely?

Can you use an Airgun for Hunting and or Pest Control?

The short answer is yes! As long as you choose the correct Airgun for the job, one that has enough power and accuracy to get the job done in a humane manner. Using an underpowered or inaccurate gun of any type for the chosen target will lead to the animal being wounded and possibly getting away to suffer unnecessarily.

What about Pistols versus Rifles?

Given the choice, a rifle will always be your best bet, rifles tend to be more accurate since they are more stable to hold and the fact that the sights are further apart which improves the guns accuracy. Most rifles also allow for enhanced sighting systems like red dots or magnified scopes for even further accuracy improvements. There are some pistols made specifically for hunting and target shooting that can be accurate but I would limit their use to shorter ranges.

What about Pellet guns versus BB guns?

BB guns in general are not meant for hunting or pest control, and in most cases they are underpowered and not as accurate as their pellet shooting counterparts, especially out at longer ranges where most pests keep their distances to. If you plan on doing some hunting and or pest control, please invest in an adequate pellet rifle to get the job done humanly.

What type of Ammo is best for Hunting and Pest Control?

There are lots of types of pellets available, pointed, rounded, flat, hollow-point and even pellets that have nylon tips. At the end of the day, use the pellet that is the most accurate in your Airgun because shot placement will win over pellet shape any day of the week. The reality is that as long as that pellet hits the target with adequate velocity, it doesn't matter what shape it is, it's more than likely going to pass right through the animal.

What is the lowest FPS that I can use?

I would rather ask the question, what is the highest fps I can get away with since more fps will give you more margin for error, since it will have a flatter trajectory and will do more damage even if your shot is off a bit. An experienced shooter could make a kill shot on a small pest even with a 400 fps airgun but the shot would have to be perfect and the range would have to be close. Of course when shooting larger game, you will need larger caliber pellets with higher velocities. Also when using a high velocity airgun you need to consider what is beyond your target, if you miss, where is that pellet or bullet going to end up? You need to make sure you do not injure anyone by mistake as pellets/bullets can travel a long distance.

How large of an Animal can an Airguns Kill?

This is really dependent on the Airgun being used, Airguns come in many different calibers, from .177 right up to .50 caliber, some PCP Airguns can even take down a deer! You need to do your research and make sure the Airgun you choose has both the power and accuracy you need for the intend prey.

Where can I use an Airgun for Hunting and or Pest Control?

This is a question you need to ask your local authorities as laws and hunting regulations are different just about everywhere. Even shooting pests on your property may require a permit so be careful to obey your local laws.

In many of my reviews I show the loading process of each gun but sometimes I either skim over this part or assume most people already know how to load an Air Pistol and skip it entirely. Well as it turns out not everybody does know how to load up an Airgun or they are unclear on certain areas, like do you actually need the CO2 and how long can you leave CO2 in an airgun?

So I made a video specifically to cover how to load CO2, BB's and/or Pellets into your Air Pistol.

Now even though this video is targeted at 4.5mm Steel BB and Lead Pellet Pistols, there is a crossover with 6mm Airsoft Pistols so this video may also help an Airsoft shooter.

Our Family Bearded Dragon (Dijon) was looking rather sad and lonely today so I figured he could hang out while I made the video, he really doesn't do much of anything most of the time so why not give him a special appearance in one of the Replica Airguns Videos ;)

Two questions that come up over and over again and to be honest I just hate answering, mainly because both of these questions to me are kind of common sense questions. I feel if someone where to stop and actually think about teh question, the answers would become obvious.

That said, common sense has to be learned somewhere and not all of us are exposed to the same life experiences so here goes...

The two questions are:

• Will this Ammunition Work in my Gun?

• Can I Convert a Blank Gun to a Real Gun?

The answer for both of these question is actually the same! Use the ammo made for your gun and do not try to use anything other than the ammo that was made for your gun. Do not try to modify your gun to shoot anything other than the ammo that was made for it, if you do, you may be breaking the law and could land yourself in jail. If you can follow these rules then your ammo and gun will work as intended :)

So that's pretty much it in a nutshell, watch my YouTube video below as I show you examples of ammo types with visuals on exactly why you need to use the ammo made for your gun. I also talk about the dangers of attempting to modify a blank gun to shoot some sort of real bullet and why it is a very bad idea in so many ways to try and convert a blank gun into a real gun.

Buy the ROHM RG-88 9mm P.A.K. Blank Pistol in the Canada Store

Buy the ROHM RG-88 9mm P.A.K. Blank Pistol in the US Store

This video should go "Hand in Hand" (pun intended) with my Best Two Handed Pistol Grip Tutorial Video that I did last year back in August. After that video I had several people ask me to talk about how to aim a gun. I guess if you have been shooting guns for a while you kind of take it all for granted but after teaching my kids the proper way to aim a gun at a target, this info is not naturally born into us ;)

This video demonstrate how and where to place your open gun sights on a target and also how you can compensate for a gun that may not be perfectly sighted in.

This is take 2 of my Modification to my F1 Chrony Chronograph. The purpose of this modification is to improve the low light FPS readings. In my first attempt I used LED Puck Lights but they where the kind that used flat panel LED's and they only had 4 panels per LED Puck which made each LED panel kind of bright. I did get OK with my first mod using LED Puck Lights but not as good as I would like to see.

So here we are with take 2 of F1 Chrony Chronograph LED Puck Light modification and this time around I am using standard bulb styled LED lights and to improve my chances of this working I went with and LED Puck that contained 24 LED bulb lights per puck, this way each light on it's own is a bit dimmer which I feel will give a more diffused lighting effect and hopeful consistent fps readings.

By the way I got these LED Puck Lights at my local dollar store for $2.50 each so not a very expensive modification, especially if they work.

Well... Watch the video and see how they perform...

This video was made to show you the results I got by mounting LED puck lights to the top of my F1 Chrony Chronograph defuser panel in order to improve the low light Feet Per Second readings when using 4.5mm Steel BB's.

I have been struggling with my F1 Chrony Chronograph during the fall and winter months as tit becomes overcast and dark where I live. There have been days where I have gone out to shoot my field test shooting video and not been able to get any Chronograph fps results which is very frustrating because much time and effort goes into the planning setup of each video.

I was given advice from several of my viewers to mount an LED puck style light on the back side of my Chronograph defuser panel and that this helps the Chronograph to read much better in low light situations.

I bought a multipack of the LED puck lights from my local Costco but they did not work as well as I expected them to as they had a panel style of LED rather than the bulb shaped LED which I think may diffuse the light a bit more. My next experiments will be done using LED Puck lights but with the bulb styled LED.

You can watch my video to see how my first attempt using an LED Puck light with my F1 Chrony Chronograph worked out.

Another quick revisit of the KWC/Cybergun M92 Beretta - Taurus full metal, full blowback, CO2 4.5mm Steel BB pistol series. They come in several flavors but are all made by KWC and in many cases redistributed licensed by Cybergun. This Field Test Shooting Video Review focuses on the Cybergun Swiss Arms P92 version.

I have several videos I made for the Cybergun GSG 92 version showcasing an early on Table Top Review, Field Test Review and even a Full Auto Mod Video.

Now that I have a more standardized Field Test Shooting format, I though I would revisit this series of KWC/Cybergun Beretta - Taurus Replica BB Pistols and do a follow up Field Test to get some more camera angles and hopefully a nice tight target grouping using my standard semi rested position from 20 feet away.

I also incorporate some high speed video near the end of this Field Test Shooting video Review to go along with the Chronograph and target portion of the Filed Test Shooting review.

The KWC - Cybergun Full Blowback All metal serious of Replica CO2 BB Pistols has been hugely popular over here at Replica Airguns and for good reason, they are very realistic in looks and operation, are priced very respectably and replicate several of the more popular semi auto pistols.

Buy the Swiss Arms P92 in Canada  -  Buy the Swiss Arms P92 in the US

In this informative video I go over the very basics of gun "handling" safety. I don't talk about gun storage or even shooting of the gun, I strictly go over the main aspects of handling a gun in a safe manor.

These are the four main points I demonstrate in this video:

• Fingers off the trigger till you are ready to shoot.

• Keep the gun unloaded till you are ready to shoot it.

• Assume your gun is loaded at ALL times.

• Always point your gun in a safe direction.

Hopefully this video will prevent some unfortunate accidents, even airgun related accidents can cause serious injuries which in most cases can be prevented with the correct gun handling information.

I have made a

similar safety video

where I talk about general gun safety and speak more about storing and also some gun shooting safety tips.

You really need to watch my Vimeo Video to see how easy it is to take a brand new out of the box gun and give it that weathered, old, worn and used look that you would find in a classic vintage gun like a Luger P.08, Colt 45 1911 or any other classic firearm. Of course this is something you would do to a new gun that you want to make look old :)

This is a great way to take a gun that already has some wear marks on it and really give it the full worn in look, kind of an alternative to having to touch it up or refinish it.

Here is a hint... I use something magical to do it!

Buy the Umarex Luger P.08

One of the most important keys to shooting accurately is how you grip the gun! In this video I show you the two handed grip that I use and that I have learned from watching other accurate shooters. I also talk about arm and shoulder placement which is more important when shooting large caliber pistols but even when shooting airguns that have virtually no recoil you may as well practice the correct hand arm and shoulder placement for when and if you do start shooting heavy recoil guns.

The main hand grip points I talk about in this video are how to overlap your finders and thumbs and also the pressure used by each hand that will make all the difference down range when shooting at targets.

Watch my Vimeo Tutorial Video on the Best Two Handed Pistol Grip:

• Checkout my Field Test Review for the Umarex Walther P99 CO2 Blowback Airsoft Pistol:

Type: Airsoft Pistol.

Manufacturer: Umarex.

Model: Walther P99 DAO

Materials: Metal & Polymer.

Weight: 1.5 pounds.

Barrel: 4 inches, metal non-rifled.

Propulsion: 12 gram CO2.

Action: Semi auto, double action only with blowback.

Ammunition Type: 6mm plastic Airsoft BB's.

Ammunition Capacity: 15 round stick magazine.

FPS: 380.

Trigger Pull: The Double Action Only trigger pull on the Umarex Walther P99 CO2 Blowback Airsoft Pistol is long but not overly heavy for a double action trigger, it does have a break point mid way where it locks partway back, I presume this is the point in which a BB is loaded from the magazine into the barrel? The rest of the pull is still medium but much shorter with a distinct release point.

Accuracy: I did do a quick preliminary test before I made this table top review to get an idea of where this gun performs in terms of FPS and accuracy, I shot 5 rounds through my Chronograph on a fresh CO2 and got an average of 333FPS which was a bit lower than the claimed 380 but it was not the hottest of days. I also stepped back 20 feet and from a semi rested position I was able to get 9 shots within 2 inches of each other which was not bad for a DAO gun that I have never shot before. I did shoot a bit down and to the left with the set sights.

Build Quality: The Umarex Walther P99 is well built for its rather low price tag, it may not have all the bells and whistles but it does get the job done with good fit and finish and materials used. You will find a plastic/polymer frame but there is a lot of metal where it would normally be found on the real steel version like in the slide, magazine, trigger, slide catch, magazine release, inner barrel and many other internal parts. No real complaints here!

Realism: The Umarex Walther P99 CO2 Blowback Airsoft Pistol is pretty close in looks to a real steel Walther P99 with the exception of a missing decocker, but I'm pretty sure this is the same with the real steel DAO version? There is also the funny looking safety on the right side of the frame found on many Umarex airguns. I have to mention the red tip but again this can be removed and even when removed the barrel it is still recessed which adds to the realism. The Blowback action, Walther licensing and nice heavy weight all add up to make this Airsoft pistol look and feel the part.

Purchase it from: The Replica Airguns Store

Pros:

• Low cost for a very believable and solid replica.

• All metal stick magazine.

• Metal slide and internal parts gives it decent weight.

• Rail for accessories.

• Well hidden CO2 screw.

• Walther licensing.

• Recessed inner barrel.

• White dot sights, easy to use.

• Right amount of power for indoor CQB style airsoft games.

Cons:

• Comes with a red tip even in Canada.

• Double action only, so trigger is a bit heavier.

• Kind of funny safety, not like the real gun.

• Blowback was a bit sluggish.

Comments:

Overall the Umarex Walther P99 CO2 Blowback Airsoft Pistol is a very good buy, it's a decent replica of the real steel Walther P99 with blowback operation, lots of metal parts, good fit and finish, decent performance and full Walther licensing and trademarks. All at a very affordable price tag. It may lack some of the extras you will find on more expensive and more functional Airsoft pistols but the simplicity of the Umarex Walther P99 CO2 Blowback Airsoft Pistol means it will most likely be a bit more reliable with less to go wrong down the road. If you have been looking for a nice Walther styled replica in an Airsoft version this may be just be the ticket!

My Vimeo Video Review for the Umarex Walther P99 CO2 Blowback Airsoft Pistol:

Buy the Umarex P99 CO2 Pistol in Canada 

Buy the Umarex P99 CO2 Pistol in the US

Here is a quick Update video of three Airsoft guns, two of which I have touched upon before but have not gotten around to doing any actual Table Top or Field Test Shooting videos for you (The ASG Dan Wesson Airsoft Revolver and the Umarex P99 Blowback Airsoft Pistol). I also show you a new Umarex Airsoft Gas Blowback PDW, the H&K MP7 A1, a very realistic version I am sure will be of interest to many of my Airsoft fans.

I will be doing proper Table Top and Field Test Videos for each of these Airsoft guns as soon as I can get to them all, starting with the Umarex Gas Blowback H&K MP7 A1 Airsoft PDW so stay posted for these upcoming video reviews...

Buy ASG Airsoft Pistols in Canada  -  Buy ASG Airsoft Pistols in the US

Buy this Airsoft Pistol in Canada  -  Buy this Airsoft Pistol in the US

Buy this Airsoft Machine Pistol in Canada  -  Buy this Airsoft Machine Pistol in the US

After many many requests to show how the Umarex Walther PPK CO2 Tab Modification is done I have relented to public demand. I don't actually cut my tab in this PPK CO2 Tab Modification Video but I do go step-by-step in detail and compare my modified Umarex PPK to my unmodified Umarex PPK. It is really very basic on how this is done and only a hack say and perhaps a file are all that is required to make the modifications to the PPK CO2 tab in order to make it flush with the bottom of the handle area.

Your best bet is to simply watch my YouTube Video located below and follow the steps there but here it is in text form:

1. Place an empty (already pierced) CO2 into your Umarex Walther PPK and tighten the unmodified CO2 tab until fully tightened, just like you would tighten a fresh CO2.

2. Take note at how many threads are exposed between the bottom of the handle and the top of the plastic CO2 tab, there should be about 2-4 threads exposed.

3. Unscrew the CO2 tab all the way, place the PPK BB Pistol so it is secure (in a vice of some sort) and use a hacksaw or dremel to shorten the CO2 screw just above the plastic tab at the thread location you previously noted. Be conservative as you can always cut or file the screw a bit shorter if your first cut was not short enough.

4. Now use the same hacksaw or dremel to cut a notch in the exposed cut area of the CO2 screw so that you can use a slot screwdriver to tighten the CO2 screw.

5. That's it - Enjoy your modified Umarex Walther PPK CO2 BB Pistol!

Watch my Vimeo Video of the Umarex Walther PPK CO2 Tab Modification Tutorial:

Buy the PPK/S in Canada   -   Buy the PPK/S in the US

Every once in a while something goes wrong and your favorite BB shooter stops working as it should :( One of the most common problems I see with many of the full blowback BB and Airsoft pistols are BB's getting stuck in the gas tube. This is because this style of gun loads a BB into the breach area of the barrel every time you rack the slide forward. Of course this is only when there are BB's in the magazine.

The semi auto style of these guns is similar to that of a real gun, the blowback operates the slide which in turn moves back and then forward and loads a BB into the chamber. With a real gun, if you where to rack the slide manually again without shooting it, the chambered round would be ejected by the extractor but with a BB gun there is no extractor because there is no spent shell to eject. So multiple BB's can be loaded into the chamber area of the barrel overloading it and if the BB's have nowhere to go they just jam up and often go back into the gas tube which can cause all kinds of problems...

In this Cybergun KWC Tanfoglio Witness 1911 Stuck BB Removal Tutorial Video, I show you how to remove a BB or even multiple BB's from the gas tube area which in short requires; the removal of the slide and guid rod and spring so that you can push the gas tube forward and shake the BB out of the front of the gas tube.

Watch my Vimeo Video on how to remove a stuck BB from the Gas Tube on my Tanfoglio Witness 1911.

Buy KWC/Cybergun 1911 BB in Canada   -   Buy KWC/Cybergun 1911 BB in the US

This is not meant to be a full review of either the BB or Airsoft version of the Cybergun - KWC CO2 Blowback Mini UZI's but I do talk about specifications, show you around both guns, and put them both through a full Field Test so I guess in a way, perhaps it can be considered to be a full review ;)

I will list the specifications here for you but I am not going to get into details like Trigger Pull, Build Quality, Accuracy and Realism. You can check out my other video reviews for more information on the Mini UZI:

• Cybergun 4.5mm CO2 Blowback Mini UZI Review

• Cybergun - KWC Mini UZI 4.5mm BB Gun Full Auto Modification

• Cybergun Mini UZI CO2 4.5mm BB Gun Chronograph and Full Auto Shooting Test

• Dual Full Auto BB Machine Gun Destruction

Type: CO2 Blowback Machine gun.

Manufacturer: Cybergun - KWC.

Model:Mini UZU.

Materials: Metal and Polymer.

Weight: 4.8 pounds.

Barrel: Metal, non-rifled.

Propulsion: CO2 x1.

Action: BB Semi auto only - Airsoft selectable semi & full auto, single action only.

Ammunition Type: 4.5mm Steel BB - 6mm Plastic Airsoft

Ammunition Capacity: 25 - 38 rounds

FPS: 350 - 400

As I said you can check out all my other videos for info on these very accurate Mini UZI Replicas, I mainly want to go over some of the main differences and similarities for both the BB and Airsoft versions.

In terms of build quality they are made almost exactly the same and weigh in at a hefty near 5 pounds, the only differences are the inner barrel and magazines to accommodate the different sized ammo. The BB version has a 25 round single stack magazine that does not have a follower to stop the bolt from continuing to operate even after the magazine is empty. While the 6mm Airsoft version has a double stack magazine that holds 38 rounds and does have a follower to stop the bolt which can save you some unintentional wasted CO2.

The Airsoft Mini UZI version is distributed by KWC while the 4.5mm BB version is distributed by Cybergun, you will find the UZI and IWI licensing on the Cybergun 4.5mm BB version but not on the KWC 6mm Airsoft version.

Out of the box the KWC Airsoft Mini UZI is ready to go in both semi auto and full auto while the 4.5mm steel BB version will only shoot in semi auto mode, it can however be easily modded to shoot in full auto.

Both guns come in cardboard boxes with manuals, some BB's and an Allen key to tighten the CO2. The KWC Airsoft Mini UZI also comes with a handy speed loader.

There is a slight fps velocity difference between the two with the KWC Airsoft 6mm plastic rounds traveling at around 400 fps (with .20 gram BB's) and the 4.5mm Steel BB's traveling at right around 350 fps. In the field test portion I test both guns out on some water filled cans to see how each ammo type performs in terms of penetration.

Your best bet is to watch both my Table Top and Field Test Comparison Video Reviews and see for yourself how they compare!

Buy BB Mini UZI in Canada   -   Buy BB Mini UZI in the US

Buy Airsoft Mini UZI in Canada   -   Buy Airsoft Pistols in the US

• Also Checkout my Field Test Shooting Review for the Cybergun Sig Sauer P226.

Type: 6mm Plastic BB Airsoft Pistols.

Manufacturer:Cybergun

Model:Sig Sauer P226

Materials: Metal slide & frame.

Weight: 2 pounds (920 grams).

Barrel: Metalnon-rifled smooth bore.

Propulsion: Gas Blowback (GBB).

Action: Single and double action.

Ammunition Type: 6mm plastic Airsoft BB's.

Ammunition Capacity: 26 rounds.

FPS: 383 fps (Using .12 gram BB's).

Trigger Pull: The trigger pull on the Cybergun Sig Sauer P226 Airsoft Replica is good in both single and double action. Once the slide is pulled back and released the first round is chambered and the hammer will remain back placing the P226 in single action mode, the pull is light and the take-up is fairly short, most of your shots will be in single action mode unless you use the de-cocker to lower the hammer for a subsequent double action next shot, double action shots are still pretty light but much longer in order to cock the hammer.

Accuracy: Shooting the Cybergun Sig P226 from 20 feet out in semi rested position I was able to get very good results. I placed 10 rounds in about 1.5 inches with the shot placement being a bit low possibly due to my barrel mod, adjusting the hop-up may bring the aim point back up to where it should be. The Sig Sauer P226 Airsoft Replica shot right around the 316 fps range while conducting my 5 shot average chrony testing which was lower than advertised but I was using much heavier .20 gram BB's. You can expect to get a full magazine worth of shots out of each gas fill-up but I did notice that as the magazine got colder it did tend to become much less efficient and also seemed to vent a lot of vapor.

Build Quality: The build quality is generally good and I was surprised at the finish on this model as the paint is not showing any wear marks so far, the fit is good with minimal slide and barrel wobble and everything is working very well with no problems so far with a fair amount of shots through it, guess you could say I like shooting this gun :) Most of the gun is metal with only the grips and a couple internal parts being plastic.

Realism: The Cybergun Sig Sauer P226 6mm Airsoft pistol is a replica of the real steel Sig Sauer P226 right down to the licensing and it really is a great looking and functioning Airsoft Replica. You can field strip this gun exactly like a real Sig and all the mechanical parts work just the same including a working de-cocker and adjustable front sight.

Available in the:Replica Airguns Store

Pros:

• All metal pistol with good overall realistic weight to it.

• Very crisp and firm full blowback operation.

• Excellent fit and finish - paint seems to be wearing well.

• Nice accurate looking and working Sig Sauer P226 Replica with licensing

• Working de-cocker.

• White dot sights for quick target acquisition.

• Front sight is adjustable for windage.

• Full size drop out magazine holds BB's and gas.

• Fully field strip-able.

Buy this Airsoft Pistol in Canada  -  Buy this Airsoft Pistol in the US

Cons:

• Comes with an orange tip not required for Canada.

• Seemed to shoot a bit low for me, could adjust with hop-up a bit?

• Only one magazine per Gas fill.

Comments:

I am a big Sig Sauer fan so it would take a lot for me to not give this gun a good review, with that said it performed pretty well, sure it was not the most powerful but I was using gas over CO2 so I was not expecting too much, it also shot a bit low for me but again that may have been because of the barrel mod so who really knows for sure at this point ;) And yes it came with that unsightly orange tip that I took short work of removing. At teh end of the day I still love it and it performed well without letting me down, just like a would expect from a real Sig Sauer!

My Vimeo Table Top  Review of the Cybergun Sig Sauer P226 GBB Blowback Airsoft Pistol:

Buy this Airsoft Pistol in Canada  -  Buy this Airsoft Pistol in the US

• Also Checkout my Table Top Review for the Cybergun Sig Sauer P226.

I usually do my Table Top Video Review first but this time around I did my Field Test Video Review first since I was all setup checking out a couple other guns at the time. When I do my detailed Table Top Video Review for the Cybgergun Sig Suer P226, I'll post the link here so stay tuned. If you have not already checked out my Barrel Mod Video for this same gun then check that video out where I remover the extended orange portion of the metal barrel and make the barrel flush with the end of the slide which is how the real steel version was originally made.

Getting back to the Cybergun Sig Sauer P226 GBB blowback Airsoft Pistol field test, as per usual I test this Airsoft semi auto gas blowback pistol on the Chronograph to see what kind of real world velocity I get and since I had some Green Gas on hand, I used it for this part of the review and got an average of 315 fps with a six shot string.

I also stepped back 20 feet and shot 10 times at my stationary target using a semi rested position (sand bag up front and kneeling in the back). Even though the Sig Sauer P226 shot a bit low I did get about a 1.25 inch group with the exception of one flyer that hooked down just a bit making the 10 shot group a bit wider at just under 2 inches. The low shot placement may have been caused by my barrel mod but since I did not do a before and after test, I can not say for sure?

Make sure to watch my YouTube Video of this Field Test as it also includes some nice slow-motion of the slide blowback at both 400 and 1200 frames per second.

Watch my full Video Field Test Shooting Vimeo Video below:

Buy this Airsoft Pistol in Canada  -  Buy this Airsoft Pistol in the US