Moving on to the head to head comparison of the Tanfoglio Gold Custom versus the Sig Sauer X-Five Sight Rail (Open version). Again like my previous video of the KWC Model M1911 Tac A1 versus the Cybergun-KWC GSG 92-M92, these two Air Pistols feature full size drop out metal magazines that hold the CO2 and 4.5mm steel BB's, along with full blowback with working slide catches, safeties and magazine releases. Both are field Strippable and both have the addition of sight rails with red dot sights for quick target acquisition.
I did not find either sight rail pistol to be all that much more accurate than similar open sight pistols like the KWC Model M1911 Tac A1 and Cybergun-KWC GSG 92-M92, but I did find that target acquisition was much quicker and even when I accidentally double tapped the trigger, the second round was right on target.
In this field test comparison I shoot both guns through my Chronograph to see what kind of feet per second performance each one shoots, I also take them back 30 feet and shoot 10 rounds on a paper target using a semi rested position for true accuracy results.
Watch my Field Test Head to Head Shootout for the Tanfoglio Gold Custom versus the Sig Sauer X-Five Sight Rail:
Both CO2 4.5mm Replica Air Pistols feature full size drop out metal magazines that hold the CO2 and 4.5mm steel BB's. These super realistic BB guns also have full blowback with working slide catches, safeties and magazine releases and they can both be field stripped juts like the real steel versions.
In this field test comparison I shoot both guns through my Chronograph to see what kind of feet per second performance each one shoots, I also take them back 30 feet and shoot 10 rounds on a paper target using a semi rested position for true accuracy results.
Watch my Field Test Head to Head Shootout for the KWC Model M1911 Tac A1 vs Cybergun-KWC GSG 92-M92:
I get many question over on my Vimeo Channel, lots of times people asking me which gun is better and in most cases it really comes down to personal preference. But in some situations the comparisons are really close and to be honest it's even hard for me to decide which gun I think is better.
I get asked which one has higher fps, or is more accurate, or has harder blowback recoil... the list goes on. Without actually taking both gun outside and doing a head to head test using the same exact situations, I really can not honestly tell you! So that's exactly what I am going to do. Take some of the most commonly asked about gun comparisons and have a showdown.
Over the next while I will be making a total of five separate videos where I compare the following CO2 BB pistols head to head:
Trigger Pull: Both of these pistols have about the same style of triggers, they both shoot in true revolvers style offering single and double action triggers. The double action has a bit of friction to it since the cylinder is being rotate during the first part of the trigger pull and there is a spring fed metal gasket between the barrel and the cylinder that creates a seal but does apply pressure and results in some friction and a heavier trigger pull in double action. Single action is much lighter on both guns.
Build Quality: These detailed revolver are really well built! Both are almost all metal with just a few components made out of plastic, like the handles on both guns and the CO2 screw tab on the Dan Wesson. Both revolvers grips gave me just a bit of concern, you will need to be careful when snapping in the grip on the G&G G731 and the Dan Wesson grips have been known to ware a bit with heavy use. The finish on both of these guns is amazing and while the Silver finish on the G&G looks just like polished stainless steel, the Gold finish on the Dan Wesson offers a very unique and customized finish not found on too many guns. And if you just want classic black then there is always the G&G G731 in standard black as an option.
Realism: The ASG Dan Wesson and G&G G731 revolvers are as close as you can get to real six shooters, all the parts work pretty much like a real revolver, the realistic loading of the metal shells not only make it feel like you are handling a real revolver but also finish off the look making it really hard to tell that both these pistols are in fact Airsoft Revolvers.
G&G G731 is super compact and flush, great out of the way back up side arm.
No Red Tip on the Canada version.
Cons:
Plastic CO2 screw tab on the Dan Wesson (but is well hidden and protected).
A bit of concern with wearing and usage on the grips for both guns.
No adjustable sight on the G&G G731 but super clean looking.
Red tip on the US version :(
Comments:
As with all of these shell loading revolvers, they are just so realistic and really fun to load up and shoot. You actually get a bit of time in-between shooting to take a breath and enjoy the entire experience rather than just unload round after round with some of the other super high round magazine guns. I love the compact size of both guns, perhaps the G&G G731 just a bit more with it's super clean edges and even smaller profile. But on the other hand the Dan Wesson ASG 2.5 inch has that more aggressive combat look if that is more to your liking! Either way, both guns make a great choice for an out of the way revolver styled side arm when you need that extra backup firepower!
My Vimeo Video Table Top Review for these compact realistic Airsoft Revolvers:
You may wonder why I am doing another video on the G&G CM16 Raider Gas Blowback Airsoft AR Rifle? That's because the one I have here in this Update Video is Version 2 and yes there is a difference. So far I can only tell you about the obvious stuff since I really have not tested it out to see if there are any other performance gains with Version 2 over Version 1.
G&G has made some improvement with Version 2 enhancing several areas:
First off, there is now a selector switch on both sides of the receiver allowing for left or right handed use.
Carrying on with the ambidextrous theme, G&G also added a magazine release to the left side of the receiver.
Another missing feature was a bolt lock out when your magazine was empty, this has been added and so the bolt will lock back about 1/3 the way back locking out the gun and letting you know when you are out of ammo.
The bolt release on Version 1 was just for show and did not function. On Version 2, with the bolt lock, G&G also added a working bolt release.
Those are some pretty significant improvements to the G&G Armament CM16 Raider GBB Version 2 in my books! So now it's time to test it out and see if full auto mode has been improved. I found with Version 1, that when using full auto, the G&G CM16 Raider GBB would have some trouble getting through a full mag dump but when shooting very quickly in semi auto had no problems at all.
Trigger Pull: The trigger pull on the King Arms Thompson Machine Guns is fairly short and light as it is essentially just an on-off switch for the internal electronic components. You can shoot this gun very quickly in semi auto mode, and of course even quicker when full auto is selected. As with all AEG systems their is a slight delay between when you pull the trigger and the shot is taken as the internal spring needs to compress first before releasing.
Accuracy: In many cases Airsoft guns can be just as accurate as 4.5mm BB guns, well at least at fairly close ranges, I was able to get most of my .25 gram BB 10 round target test shots within 1 inch from 30 feet away using a semi-rested position. There where a couple BB's that lengthened the group out to about 2 inches but still a very good result when you consider these are plastic BB's being used. In Terms of FPS, I did stick with the slightly heavier 2.5 gram Airsoft BB's and still got a decent 360 average 5 shot Chronograph test result making this AEG Airsoft rifle perfect for just about any Airsoft game type.
Build Quality: The King Arms 23 Karat Gold and Chrome Platted AEG Thompson Machine Guns are very well made using Aluminum Zinc Alloy bodies and real Wood Stocks, the fit and finish is very good and pretty much everything on these rifles are either metal or wood. You will have to polish these guns with a cloth from time to time since the mirror finish shows every smudge and finger print.
Realism: I'm not sure how many real 23 Karat Gold and Chrome Platted Thompson Machine Guns there are out there but there has to be at least a few ;) But going on how these guns look and feel, they are solid and very realistic. Some people have mentioned that the bolt should be on the top for some versions of the Thompson's but there are some Thompson's with the bolt on the side so I suppose we will let that one slide. The Wood stocks are a real plus adding to the overall weight and authenticity. Most parts works as they would on the real steel Thompson M1A1 Military or M1928 Chicago (Gold or Chrome) AEG Airsoft Machine Guns.
Nice high capacity metal magazines, can be mixed and matched.
Adjustable rear sight for windage with two sight positions (Notch & Peep).
Semi and full auto selectable with really nice rate of fire.
FPS is bang on for indoor or outdoor Airsoft games.
Fully Thompson licensed.
Comes with Certificate of Authenticity.
Cons:
Does not come with a battery or charger.
Prone to finger prints and smudges.
Need to use a screw driver to get at the battery.
Comments:
I am a big fan of the King Arms Thompson line, even the all black version with the plastic stocks looks and functions great. Internally the lower cost black version is the same and having previously shot my black Thompson, I knew these blinged out 23 Karat Gold and Chrome Platted versions where also going to perform as good as they looked! I'm not so sure about buying a Gold or Chrome Thompson for everyday use, since they will get knocked around and scratched up but if you are looking for the best of the best with real wood stocks and all metal parts then make sure to consider one of the Thompson
My Vimeo Video Review for the King Arms Thompson Gold & Silver AEG Airsoft Machine Guns:
As usual with my Field Test Shooting Reviews I test out both Umarex pistols using my Chronograph and put five rounds through it with each CO2 BB Pistol to get a real world average fps. Umarex claims around 410 and I got pretty close with both pistols using a brand new Umarex CO2 cartridge in each gun. The temperature was not overly warm as we are now into fall here in Canada BC but so there may be room for a bit higher fps out of each Umarex CO2 BB pistol.
I decided to shoot both 4.5mm Pistols at the 20 foot target potion of this review since I had not done any pre tests. While shooting from a semi rested position at 20 feet back I was able to get pretty much a 2 inch 10 shot group with each gun, the XBG seemed to group a bit tighter for me than the TDP 45 and both BB Pistols shot pretty well centered on target. The trigger pull is very typical for this style of double action only trigger, kind of long with a slight sticky click in the middle while the BB chambers and then some more trigger pull with a fairly predictable release right near the back.
Both Umarex BB Pistols should get right around 6-7 consistent magazines worth of shots before having to change the CO2, that is 120+ shots! And even on the last magazine the fps seemed to stay nice and high.
Both Umarex CO2 BB pistols performed pretty well considering the super low cost and make great inexpensive plinkers that will get you decent power, more than adequate accuracy and lots of shots out of a single CO2.
My Vimeo Field Test Video Review for these Umarex CO2 BB Pistols:
I wanted to feature some Walther knives we sell over at our online Canada Replica Airguns Store, these Walther Knives are low cost but high value and would make either a great gift or a nice treat for yourself. If you're already ordering something else from us then save on the shipping a bit by getting one of these Walther Knives at the same time.
The Walther Knives I feature in this YouTube video are the:
The Walther Sub Companion Folding Knife is an excellent all purpose folding knife. The Sub Companion features a 440 Stainless Steel spear point blade that can handle most any utility chore. The thumb disk opener works equally well for righties or lefties and the polymer handle is textured for a sure grip.
The Walther Sliver Tactical folding knife has a 440 stainless steel blade 7.36 open 3.1 non-serrated blade .125 blade thickness 6.40 oz. Thumb stud Open assist Liner lock Aluminum scales Removable pocket clip Glass-breaker on pommel Includes a synthetic pouch Whether you're looking for a survival knife or just another general-use edged tool, this should fill the bill. This combat folding knife will be useful in so many ways, you'll wonder how you got along without it.
The Walther Black Tactical folding knife features a 441 stainless steel blade 7.8 open 3.3 partially serrated blade .130 blade thickness 6.40 oz. Thumb stud Open assist Liner lock Aluminum scales Removable pocket clip Glass-breaker on pommel Includes a synthetic pouch Whether you're looking for a survival knife or just another general-use edged tool, this should fill the bill. This tactical folding knife will comfortably fit in your hand and do whatever comes its way. At this price, you can afford to include one in your glove compartment and your range bag.
Yet another option for you when looking to purchase a KWC/Cybergun Colt model 1911 or Beretta/Taurus M92. We started out with the Cybergun Tanfoglio Witness 1911 and GSG 92, then added the KWC non-licensed versions. Now we give you yet another option, the Cybergun distributed Swiss Arms P1911 and Swiss Arms P92, same BB guns but brandishing the Swiss Arms markings and licensing.
At the end of the day all of these blowback air pistols are basically the same, all of them are made by KWC, all are made to the same quality and all are totally awesome.
It may just come down to which one we have in stock or if you want that super clean look then go for the KWC model as the slides on the non-licensed versions tend to have no markings or warning instructions on them.
FPS: 750 with Pellets and 800 with BB's for the US version (Up to 495 with Canada version).
Trigger Pull: The trigger pull on the Crosman MK-177 is medium length and fairly light. The trigger mainly releases the bolt so no pre-cocking of the trigger is required. The trigger is plastic but seems to work just fine as there is no real load on the trigger when shooting, you do need to get used to where the release point since there is some take up well before the trigger releases.
Accuracy: I found the Crosman MK-177 Air Rifle to be a very good shooter, getting about a 1 inch 10 shot grouping from 30 feet out in a semi rested position (sand bag up front, standing in the back). I also put 3 rounds through my somewhat failing Chrony Chronograph using 3,5 & 10 pumps and the MK-177 with the maximum 10 pump shot as high as 631 fps using 6.9 grain RWS lead pellets. I would expect the Canadian detuned version to shoot well below the 500 fps Canada limit much like my Canadian Crosman M4-177 I reviewed a while back.
Build Quality: The Crosman MK-177 Multi-pump Air Rifle is mostly molded plastic, but for a $100-ish Military Styled Replica Air Rifle it hits the mark in terms of affordability and if it was an all metal airgun you would more than likely expect to double or tripple this price point! Even though plastic is used throughout this Air Rifle, there are some internal metal parts where they need to be, the fit and finish seems to be good and I do not get the feeling the Crosman MK-177 is cheaply made in any way. The fact that most parts are molded means there is very little that can snap or break off and will make this air rifle even more durable longterm.
Realism: The Crosman MK-177 is a lose replica or copy of an FN SCAR Assault Rifle or ACR. It is not exact in terms of true dimensions to accommodate the pumping mechanism, You will not find very many working parts as just about everything is molded into the plastic on this Crosman MK-177 rifle. Unlike the Crosman M4-177 the lower magazine area is not removable and the rear stock is also none adjustable, I am not sure why Crosman didn't add these features to the MK-177 like they did to the M4-177? I am glad to see another Replica Assault rifle on the market as so few of them are available in Pellet or steel BB shooters.
None red dot version comes with detachable and adjustable iron sights.
Rails on top and sides for accessories.
Option of shooting pellets or BB's, I would stick to pellets and save the barrel since it is not semi auto.
Feels super solid since there are very few moving parts that could break.
Looks like the Crosman M4-177 Pellet magazines are compatible.
Cons:
Mostly plastic and just about everything is molded into the gun.
Bolt and magazine are on opposite sides?
Would of been cool if Crosman made a dedicated BB magazine?
Comments:
The Crosman MK-177 Multi-Pump Pellet/BB Air Rifle is very much like it's brother the Crosman M4-177 with a few plusses and a few minuses when comparing the two of them together. On the plus side the MK-177 has a bit more power and also the pumping is much easier while yielding higher internal pressures. On the downside the Crosman MK-177 is almost entirely molded plastic with no removable lower magazine or adjustable stock, and the bolt has been switched around to what I feel is the wrong side since now you need to index the magazine on one side and work the bolt on the other requiring a less efficient approach. Either way it is nice to have another replica air rifle on the marker and for the relatively low price you get a nice accurate pellet rifle, great for target shooting and even small pest control.
Watch my Vimeo Full Video Review of the Crosman MK-177 Pellet/BB Air Rifle:
After many many requests to show how the Umarex Walther PPK CO2 Tab Modification is done I have relented to public demand. I don't actually cut my tab in this PPK CO2 Tab Modification Video but I do go step-by-step in detail and compare my modified Umarex PPK to my unmodified Umarex PPK. It is really very basic on how this is done and only a hack say and perhaps a file are all that is required to make the modifications to the PPK CO2 tab in order to make it flush with the bottom of the handle area.
Your best bet is to simply watch my YouTube Video located below and follow the steps there but here it is in text form:
Place an empty (already pierced) CO2 into your Umarex Walther PPK and tighten the unmodified CO2 tab until fully tightened, just like you would tighten a fresh CO2.
Take note at how many threads are exposed between the bottom of the handle and the top of the plastic CO2 tab, there should be about 2-4 threads exposed.
Unscrew the CO2 tab all the way, place the PPK BB Pistol so it is secure (in a vice of some sort) and use a hacksaw or dremel to shorten the CO2 screw just above the plastic tab at the thread location you previously noted. Be conservative as you can always cut or file the screw a bit shorter if your first cut was not short enough.
Now use the same hacksaw or dremel to cut a notch in the exposed cut area of the CO2 screw so that you can use a slot screwdriver to tighten the CO2 screw.
That's it - Enjoy your modified Umarex Walther PPK CO2 BB Pistol!
Watch my Vimeo Video of the Umarex Walther PPK CO2 Tab Modification Tutorial:
Ammunition Capacity: 13 round full size metal magazine -18 round metal stick magazine.
FPS: 428 - 380.
Trigger Pull: There is a lot of difference between the trigger on both of these guns, first off the Umarex Makarov has both a single and double action trigger/hammer while the KWC Makarov has a double action only trigger/hammer. Comparing the double action of both guns the definite advantage goes to the 4.5mm Steel BB shooting Umarex Makarov as it is shorter and lighter, the KWC Airsoft Makarov does not have a bad trigger but it is much longer and a bit heavier, but still very usable. The single action trigger on the Umarex Makarov is not really any lighter than when shooting in double action, it is however much shorter with a medium take-up and predictable release.
Accuracy: Both Airsoft and BB Makarov's performed very well in their shooting tests for me, they bot shot fairly well centered with the KWC Makarov getting all five shots in the black bullseye and the Umarex Makarov having a tighter group but just off to one side. This was good news since both guns do not have adjustable sights! They also scored very well in the velocity department shooting over their advertised claimed feet per second rating. The Umarex BB version shot a very respectable 390 fps while the KWC Airsoft pistol shot a very surprising 480 fps well over the claimed factory 430 fps. Both guns also shot very accurately out to ranges of 50 feet or so. From a single CO2 I was able to get 162 shots from the Umarex Makarov and 112 shots from the KWC Makarov before I noticed a significant power drop.
Build Quality: Neither one these Makarov replicas is going to win a prize for build quality, some shortcuts have been made to keep the price down on each model, but they are both built with mostly metal parts and they both performed perfectly for me during my testing. The Umarex 4.5mm Steel BB Makarov did have more moving parts while the KWC did weigh in a bit heavier, both guns had reasonable fit and finish to them.
Realism: In terms of being good Makarov replicas the pair for sure look the part, size and overall weight are very true to the original real Steel Makarov PM with the Umarex Makarov having a working slide, Makarov licensing and the ability to be field stripped. The KWC Makarov had a nicer recessed barrel and full size drop out metal magazine. I was not a big fan of the KWC screws on the right side slide or the Umarex exposed CO2 tab.
KWC may shoot a bit too hot for CQB Airsoft games.
Both guns do not have adjustable sights.
Comments:
To be honest when I got the KWC Airsoft BB shooting Makarov, I was not all that awe struck, the lack of a working slide, DOA trigger and screw holes in the slide put me off just a bit. This Airsoft pistol did warm up to me a lot once I shot it, I was surprised by the very high fps and how accurate it was for such a low cost Airsoft pistol. I can really see this gun being used as a backup or sidearm in an out doors style Airsoft game where you may need to shoot targets out at range where other lower powered pistols just would not be able to get out to. The Umarex Makarov has always had a place in my heart, it is just a really good little CO2 BB pistol for the price with mostly all metal parts, a working slide, single and double action trigger and very good overall performance. In my books you can not go wrong choosing either of these Makarov replicas so choose wisely!
My Vimeo Video Table Top Comparison Review for these Makarov Air Replicas:
This is not meant to be a full review of either the BB or Airsoft version of the Cybergun - KWC CO2 Blowback Mini UZI's but I do talk about specifications, show you around both guns, and put them both through a full Field Test so I guess in a way, perhaps it can be considered to be a full review ;)
I will list the specifications here for you but I am not going to get into details like Trigger Pull, Build Quality, Accuracy and Realism. You can check out my other video reviews for more information on the Mini UZI:
As I said you can check out all my other videos for info on these very accurate Mini UZI Replicas, I mainly want to go over some of the main differences and similarities for both the BB and Airsoft versions.
In terms of build quality they are made almost exactly the same and weigh in at a hefty near 5 pounds, the only differences are the inner barrel and magazines to accommodate the different sized ammo. The BB version has a 25 round single stack magazine that does not have a follower to stop the bolt from continuing to operate even after the magazine is empty. While the 6mm Airsoft version has a double stack magazine that holds 38 rounds and does have a follower to stop the bolt which can save you some unintentional wasted CO2.
The Airsoft Mini UZI version is distributed by KWC while the 4.5mm BB version is distributed by Cybergun, you will find the UZI and IWI licensing on the Cybergun 4.5mm BB version but not on the KWC 6mm Airsoft version.
Out of the box the KWC Airsoft Mini UZI is ready to go in both semi auto and full auto while the 4.5mm steel BB version will only shoot in semi auto mode, it can however be easily modded to shoot in full auto.
Both guns come in cardboard boxes with manuals, some BB's and an Allen key to tighten the CO2. The KWC Airsoft Mini UZI also comes with a handy speed loader.
There is a slight fps velocity difference between the two with the KWC Airsoft 6mm plastic rounds traveling at around 400 fps (with .20 gram BB's) and the 4.5mm Steel BB's traveling at right around 350 fps. In the field test portion I test both guns out on some water filled cans to see how each ammo type performs in terms of penetration.
Your best bet is to watch both my Table Top and Field Test Comparison Video Reviews and see for yourself how they compare!
The KWC/Cybergun Model 1911 Blowback BB Pistols and Airsoft Pistols are very popular and so I tend to get lots of questions about them like: Are they the same quality? What version shoots the best? How do I remove the white warning lettering? Can I get one in an Airsoft version? Can I add a laser or tactical light? Can I change the grips...
So in this YouTube video I compare all four existing KWC and Cybergun model 1911's showing you the Cybergun Tanfoglio Witness 1911 in 4.5mm Steel BB, the KWC Model 1911 and Model 1911 A1 Tac also in 4.5mm Steel BB and lastly the KWC Model 1911 in 6mm Airsoft plastic BB.
Watch my Vimeo Video of these four KWC and Cybergun Model 1911 4.5mm Steel BB and Airsoft CO2 Blowback Pistols:
Trigger Pull: The trigger pull on the KJWORKS KP-05 is what you would expect from a true 1911 single action only trigger, it has very little take up with a smooth crisp and light release to it.
Accuracy: I shot the KJWORKS KP-05 from 20 feet out in semi rested position and got very good test results. I was able to place 10 rounds in under 1.5 inches and getting four shots right in the bullseye making the shot placement very good even without adjusting the sights (which can be adjusted for windage). The KJWORKS HP-05 1911 styled HI-CAPA Airsoft Replica shot right around 300 fps range while conducting my 5 shot average chrony testing which was surprisingly low for the CO2 magazine version, this may have been a temperature or CO2 related condition, when I conduct my full Field Test Shooting Review, I will review this and see if we can do better? I also got two full 30 round magazines worth of shots which is what you would expect from this style of full heavy blowback airsoft pistol.
Build Quality: I am extremely impressed with the build quality of all the KJWORKS Airsoft guns so far, the fit and finish is the best around on any of my guns including my 4.5mm steel BB shooters. After shooting several magazines worth of BB's, areas that are painted like the metal friction areas show very light wear which is rarely the case with metal built blowback airguns. Again the tolerances between the moving parts like the slide and frame are very tight showing excellent workmanship and machining from KJWORKS.
Realism: The KJWORKS KP-05 6mm Airsoft pistol is a replica of a High Capacity styled tactical 1911 45 Auto and is a great looking and functioning replica. You will not find any actual licensing on this pistol and the CO2 magazine does stick out a bit to accommodate the 12 gram CO2 but other than that this Airsoft pistol looks and works near exactly like a real 1911 tactical semi auto and is fully field strip-able. I really like the updated more tactical add ons like the tactical rail, machined trigger and hammer, white dot adjustable sights, wrap around grips and ambidextrous safety.
All metal pistol with good overall realistic weight to it.
Full heavy blowback operation.
Typical KJWORKS excellent fit and finish.
High capacity magazine 30 rounds.
Very good accuracy and well centered on target.
Nice replica of a High Capacity Tactical 1911 styled pistol.
I like the stainless highlights and ambidextrous safety and Rail for accessories.
Fully field strip-able.
Cons:
Shot a bit low Feet Per Second for me - should do better?
CO2 magazine is long to accommodate the 12 gram CO2.
Slide is heavy enough but seems to be a bit sluggish which is kind of a 1911 trademark so that can be taken as good or bad.
Comments:
The KJWORKS KP-05 1911HI-CAPA is another excellent full blowback Airsoft pistol from KJWORKS. The HP-05 is a classic upgraded more modernized version of the 1911 semi auto pistol which is a great foundation to build any pistol from. I found the CO2 usage to be decent on the KP-05 but felt that I should have been able to get more fps out of this pistol, I will be testing the KJWORKS KP-05 again and hope to see some better results in this area. With that aside, the KP-05 1911 HI-CAPA is a great shooter and as is, with its high capacity magazine would be a perfect sidearm for any Airsoft related squirmish or even just for honing up your shooting skills when getting to the gun range is not an option.
Ammunition Capacity: 18 round full size metal magazine.
FPS: 320.
Trigger Pull: The trigger pull on the KWC M1911 A1 Tac blowback BB Pistol is exactly what you would expect from a true single action 1911 styled pistol. It has a short take up and then a nice light and crisp pull to it. Because of the similar mechanics not only to the trigger but other aspects of this gun, it would make an awesome low cost trainer to be used when your real 1911 can not be.
Accuracy: I shot the KWC M1911 A1 Tac BB gun at a target from 20 feet away in a semi rested position, and it performed well getting a 2 inch grouping just a bit off center of the target. The sights are adjustable for windage so zeroing the KWC M1911 A1 Tac in would not be much of a problem! My initial Chrony testing puts this gun right in the 300-320 fps range which is just fine for this style of heavy full realistic blowback action BB shooter. I also managed to get three very good magazine worth of shots with some extra CO2 left for a potential 4th magazine. If you slow your shooting down and let the gun and CO2 warm up between magazines you can get 4 magazines with this gun for sure.
Build Quality: KWC did a great job with the KWC M1911 A1 Tac. The quality and build characteristics may even be just a bit better than my other KWC/Cybergun blowback air pistols. Everything that should be metal is the same on this as the original, the slide and barrel wiggle are minimal and the finish seems to be wearing fairly well on this KWC airgun. I do expect over time fore some of the finish to wear off on the high points but this can also give the gun some character ;)
Realism: The KWC M1911 A1 Tac BB airgun is as close as you can get to the real steel 1911 A1 45 auto but with an obvious more modern Tactical look to it, the Tactical version has the addition of a: Tac style trigger and hammer, textured grips, ambidextrous safety, adjustable white dot sights, rail for accessories. This gun is nearly all metal with very heavy blowback making it feel real to hold in the hand and shoot.
All metal construction - Good weight and solid feeling gun.
Nice heavy blowback action.
Very Accurate 1911 A1 styled replica in many way.
True 1911 Single action trigger, excellent pull, very smooth and light.
Accurate trigger design and working grip safety.
Decent accuracy, not too bad amount off shots for this style of gun about 3+ good magazines.
All metal full size dropout magazine.
Love the upgraded Tactical features (Tac style trigger and hammer, textured grips, ambidextrous safety, adjustable white dot sights, rail for accessories)
Cons:
Sacrifice fps and shots per CO2 because of the heavy blowback but worth it.
Finish on the Cybergun and KWC guns can ware off on the high points a bit but some people like this look.
Comments:
I love my Cybergun Tanfoglio Witness 1911 as do many of you based on the amount of sales we have had on that unit! After all who does not appreciate such an accurate replica of the Classic Colt 1911 A1 45 auto? The only problem with the classic 1911 is that it is missing a few of todays more modern features and that's what is so nice abut the new KWC M1911 A1 Tac BB Pistol, it takes an all ready great design and makes it even better by adding the Tac style trigger and hammer, textured grips, ambidextrous safety, adjustable white dot sights and rail for add on accessories. So if you're a 1911 fan looking for as close as you can get to the real steel in a more modern version than look no further, this is it!
Trigger Pull: The trigger pull on the ASG Bersa BP9CC is light due to its true blowback operation that cocks the internal striker back with each shot taken. For some reason there is a slight creepiness in the trigger when the metal magazine is loaded, but it does not effect the lighter weight of the trigger pull. There is also a fair amount of take-up but the reset is short.
Accuracy: I shot the ASG Bersa BP9CC Blowback Airgun at a target from 20 feet away in a semi rested position, and it performed well getting a 2 inch grouping fairly centered on the target. The sights are non-adjustable, but for me there was no real need to adjust them. My initial Chrony testing puts this gun right in the 350 fps range.
Build Quality: ASG did another great job with the Bersa BP9CC, quality and build characteristics are very similar to my CZ 75 P-07 DUTY reviewed earlier. Everything that should be metal and polymer is the same on this as the original, and the fit and finish is very good in general!
Realism: The ASG Bersa BP9CC BB gun is as close as you can get to the real steel version while still retaining a good overall working airgun, the only real giveaway is the slightly longer but-plate on the magazine (most likely to allow for the CO2 screw tab). It looks very much like the real deal right down to the licensed Bersa trademarks and the 9x19 caliber markings on the slide and ejection port.
Good power and decent accuracy for a blowback gun with good usage of CO2.
Very well made, fit and finish is very good.
Very usable white dot sights.
All metal dropout magazine.
Gun feels great in the hand, love the thin profile.
Cons:
Magazine but plate is a bit on the long side, only telltale sign. also has strange moulding marks on it.
Trigger is a bit creepy when you have a loaded magazine and if you very slowly pull the trigger a BB can drop out of the barrel if holding downward.
Blowback is mild because of the lighter slide and reduced blowback movement.
Comments:
There are few smaller blowback air pistols that not only look great but perform well, this is one of them! I love the thin profile and overall operation of this pistol, for that very same reason the real steel version is doing exceptionally well here in North America which would make this airgun version a must have for any owners of the 9mm Bersa BP9CC. I highly recommend the ASG Bersa BP9CC 4.5mm BB Blowback Pistol to anyone looking for a very good quality and realistic BB pistol that does not compromise performance and build quality.
I've already done a KJWORKS review on the KP-02, KP-07 and Elite 1A and they turned out to be very high quality Airsoft pistols so the extra price does get you a higher quality gun. So in this preview we are simply looking at some more models that from the looks of things I expect to be more of the same in terms of high quality and excellent functionality.
The KJWorks models we are looking at today are the KP-05 (1911 HI-CAPA), the KP-09 (CZ 75) and the M9 (Beretta M9). Even though none of them are licensed, they are very detailed and realistic copies of the original real steel versions with full blowback operation, heavy metal drop out magazines and lots of metal throughout. You would be hard pressed to tell them apart from the real powder versions.
All version in this preview load CO2 in the magazine along with 6mm Plastic Airsoft BB's, none of them have any orange markings or translucent parts as they fall into the uncontrolled firearms category here in Canada.
I look forward to doing my full review of these three very nice KJWorks Airsoft pistols.
I know I have been talking about this gun for some time now (Since last years SHOT Show) but the truth of the matter is Umarex did not release it all that quickly and when it did finally come out several months ago there was a recall and so the stock that came in quickly left again. So here we are now and I finally get to show everyone this very nice Umarex made Walther P38 BB shooting replica pistol.
At first glance it looks a lot like the Crosman C41, when I was at the 2012 SHOT Show visiting the Umarex booth, I thought they had just rebranded the Crosman's C41. When I took a closer look I could clearly see the difference and realism found in the Umarex Walther P38 version; like full Walther P38 licensing, blowback operation, working safety and slide catch. Pretty much everything that was missing from the Crosman C41. The Umarex P38 is a very accurate copy of a real steal P38 in almost every way.
All in all it looks to be another welcome and very realistic looking blowback BB Replica pistol and in this case one with a history that goes back to the way to World War II.
