This comparison Review Video serves a few purposes, first to compare the ASG Dan Wesson 715 Revolver 4.5mm steel BB version to the 6mm plastic Airsoft version in both velocity and accuracy. Secondly to give my new Chrony Chronograph with lighting kit a test to see if I can get more reliable readings in lower light and thirdly to try and redeem the Steel BB version of the Dan Wesson 715 as last time I tested it, it did not get all that high of fps readings, well below the claimed 430 on the box.
In this review video I test both Dan Wesson 715 Revolvers out, first with my Chrony Chronograph and then all in one take I setup and shoot 6 rounds each on separate paper targets from 30 feet back to see how accurate the smaller heavier Steel BB rounds are compared to the larger lighter Plastic BB's. I used 5.1 grain RWS 4.5mm Steel BB's and .20 gram 6mm plastic BB's and installed brand new 12 gram CO2 cartridges in both guns.
In terms of my Chrony consistency, the smaller steel BB's still struggled to get consistent readings with only 2 out of 6 shots while the larger Airsoft BB's managed to get a good reading 4 out of 6 shots. Steel BB velocity was right around 350 fps while the Airsoft BB's where travelling much faster at closer to 450 fps.
Both the Steel BB and Airsoft CO2 Dan Wesson 715 Revolvers shot 6 round grouping of about 2 inches with 4 out of the 6 shots making a much tighter 1 inch group again with both ammo types. The Airsoft Dan Wesson 715 seemed to be centered on target well while the Steel BB Dan Wesson 715 shot a bit low.
Watch and see what happens when you take an RWA M1919 AEG Airsoft Machine Gun and put it head to head against the all metal F1 Chrony Chronograph. That's right, my old temperamental Chrony F-1 Chronograph meets its first opponent! Did it survive or did it bow to the hail storm of 6mm Airsoft BB's...
Recently I picked up my new Chrony Beta Shooting Chronograph to replace my F-1 that has not been working so well for me in past videos... I wanted to get outside and give it a try shooting a few of the airguns that I was not able to test out properly. Now I know that under my patio deck, the lighting is not optimal even on sunny days and because of this I have never expected to get perfectly consistent fps recording but as many of you know, my old Chrony F-1 was pretty much not working at all near the end there.
I have ordered a light kit which will help out a lot especially when summer is over and the sky becomes more overcast. But for now I decided to test my Chrony Beta Chronograph under my deck roof as I have been testing all along and see if I can get better results with this newer Beta version.
So makes sure to watch my Vimeo video testing of my Chrony Beta Shooting Chronograph shooting a selection of airguns.
Since I pretty much took my Cybergun KWC Desert Eagle .50AE CO2 Airsoft Pistol right out of the box and started shooting I did not have the chance to set the hop-up or even figure out exactly where it was shooting and as I found out it was shooting rather high and the .20 gram BB's may have been a bit light since they seemed to spray all over. Either way I did manage to hit a few targets after eating up all the CO2 and shooting off two full mags of Airsoft Ammo...
I was personally confused about some of the similarities and differences between several models of KJWorks Beretta M9 CO2 Blowback Airsoft Pistols, so I decided to make a video where I go over 4 models of KJWorks M9 Pistols and point out the commonalities and differences between them.
Here are the 4 versions of KJWorks Beretta M9 CO2 Blowback Airsoft Pistols:
All of them come with interchangeable 25 round CO2 Magazines.
All of them shoot around 360+ fps.
All have a metal slide and frame.
All weigh close to the same weight (2.1 - 2.4 pounds).
All shoot in single and double action.
All have ambidextrous safeties.
All have white dot sights.
Prices range from $184 -$200.
Here is a list of the differences between them:
The VE, Vertex and M9A1 come in a semi gloss finish while the Tactical is more of a matt black.
The VE and M9A1 have rails for accessory attachments while the Vertex and Tactical do not.
The Vertec, Tactical and M9A1 have laniard loops while the VE does not.
Some slight trigger guard differences between the models but very subtle.
The Vertex and M9A1 share the same style classic Beretta pistol grip, The Tactical has a tactical finger pistol grip and the VE has it’s own unique pistol grip.
Make sure to watch my Vimeo video where I cover this information in detail:
Another Airsoft Pistol Preview Video to share with everyone. First up we have a nice lighter weight CO2 powered 1911 from KJWorks called the KP-11 The lower receiver is polymer which helps to keep this gun a little bit lighter all around but it still has good weight to it coming in at a little over 2 pounds, the grips are larger than some 1911's since the KP-11 has a double stack style full size drop out metal magazine. You will also find some nice Tactical upgrade like adjustable white dot sights, a lower rail for accessories and milled trigger and hammer.
I also show off an interesting and not all that common pistol from Cybergun, the FNX -45 Tactical in Gas Blowback. For import into Canada it ships with a longer barrel which stick out of the front of the gun but it also comes with a shorter barrel you can install after your receive it. The Longer barrel gives the Cybergun FNX -45 Tactical Airsoft Pistol the extra velocity to allow it to be Canada import ready. The FNX -45 Tactical is a really detailed and well built Airsoft Pistol. By the way the FNX -45 Tactical is also availabl in Dark Earth color.
Here are some of the specifications for the KJWorks KP-11 and Cybergun FNX -45 Tactical Airsoft Pistols:
Seems like all I am focussing on is Airsoft guns lately, well that's just what is coming across my table at the moment... Don't worry I am sure there will be some BB gun reviews coming up shortly :) Anyway in this Field Test Shooting Review I take a look at the ASG Bersa BP9CC CO2 Blowback Airsoft Pistol and test its accuracy and velocity. If you want some more details on this gun I have already made some other videos for the 4.5mm steel BB version so you can watch both my Table Top and Field Test Shooting videos for the 4.5mm Steel BB ASG Bersa BP9CC CO2 Blowback Pistol.
Getting to the actual Field Test Shooting review, I performed my standard five round Chronograph velocity fps test using .20 gram plastic Airsoft BB's with a brand new 12 gram CO2. The fastest Airsoft BB achieved by the ASG Bersa BP9CC CO2 Blowback Airsoft Pistol was 413 fps and the slowest came in at 342 fps with a five shot average of 390 fps. The slowest shot was the last one in my Chronograph test and it even sounded a bit different like it wasn't getting full CO2 from the valve. This would present a problem later on in my accuracy test as it seemed the CO2 valve need to working in before this gun started to perform properly. I am guessing there may have been some debris in the valve area that needed to work its way out?
On with my Field Test Shooting portion of this review to determine the accuracy of the ASG Bersa BP9CC CO2 Blowback Airsoft Pistol. I set myself up 30 feet back shooting from a semi-rested position (Sand bag up front and standing in the back). This shooting position serves to provide a stable shooting platform for overall accuracy and what I should expect to get from the ASG Bersa BP9CC CO2 Blowback Airsoft Pistol. Keep in mind the results are always dependant on how I shoot on the day of my testing.
I shot rounds through the ASG Bersa BP9CC CO2 Blowback Airsoft Pistol but as I mentioned before I believe the CO2 valve was messing with the guns performance, so what was happening was some shots would get full Co2 and work fine while other shots only got a portion of the CO2 which did not allow for the blowback action to fully cycle and caused the internal hammer to not get set in the full cocked position. I did get about half of my shots to hit the target but my results where not what I would expect from the ASG Bersa BP9CC CO2 Blowback Airsoft Pistol. It is more than capable of getting at least a 4 inch group from 30 feet out so don't take this particular test to seriously.
After tearing down my camera gear I decided to load up another CO2 into the ASG Bersa BP9CC CO2 Blowback Airsoft Pistol and shot several magazines through it. This did seem to fix the problem and which leads me to believe that I simply needed to work this gun in a little bit. Out of the box Airguns can have some machining materials in them that can cause performance issues as I believe was the case for the ASG Bersa BP9CC CO2 Blowback Airsoft Pistol. Luckily I was able to get mine working properly!
Another Airsoft Field Test Shooting Review for you guys where I test out the Cybergun distributed KWC made CO2 powered Blowback 6mm Plastic BB shooting Colt M1911 A1 Pistol. I have already done some table top Reviews for a few other versions of this same KWC made pistol... I have already made a lot of videos for this super popular KWC 1911 pistol, it comes in 4.5mm Steel BB and Airsoft version distributed by companies like Cybergun, Umarex and Gletcher to name a few. Each of these companies brands them under their own name and license and in some cases the cosmetics are a little different on each version.
Getting to the meat of this review and back to the Field Test shooting portion. I performed my standard five round Chronograph velocity fps test using .20 gram plastic Airsoft BB's with a brand new 12 gram CO2. The fastest Airsoft BB achieved by the Cybergun KWC Colt M1911 A1 CO2 Blowback Airsoft Pistol was 386 fps and the slowest came in at 374 fps with a five shot average of 380 fps. I was actually a bit surprised at how hard this Airsoft pistol shot being that the 4.5mm steel BB version shoots closer to the 300 fps range. Still a usable fps for most Airsoft games.
Next up in my Field Test Shooting Review was my accuracy target test, I set up 30 feet back shooting from a semi-rested position (Sand bag up front and standing in the back). This shooting position serves to provide a nice stable shooting platform for overall accuracy and what I can expect from the Cybergun KWC Colt M1911 A1 CO2 Blowback Airsoft Pistol. Of course the results are always dependant on how I'm shoot on the day of my testing, after all I am only human!
I shot my usual 10 rounds through the Cybergun KWC Colt M1911 A1 CO2 Blowback Airsoft Pistol but for some reason this 1911 Airsoft replica liked to shoot on the high side. My first shot curved well above my target and my second shot just clipped the metal portion. For my remaining 8 shots I lowered my aim to the lowest ring to see if I could get some shots on paper and even with this rather deliberate sight adjustment I was still hitting really high on the target, some shots still even off the paper and hitting metal. Either the adjustable BAXS Hop-up was way off or the Airsoft Ammo I was using did not agree with this 1911 pistol. It is kind of hard to say what kind of grouping I can actually get using this pistol as it stands but from shooting similar versions of this pistol I should be able to get at least 2 inch groupings once it is set up right and using ammo that works well with it.
The Cybergun KWC Colt M1911 A1 CO2 Blowback Airsoft Pistol has a great single action trigger with the feel you would expect form a real 1911 45 caliber pistol. The blowback action is strong, you can actually feel it not just in your hand but further back in your arms and even shoulders a little bit. I'm pretty sure with a quick hop-up adjustment or ammo swap, this Cybergun KWC Colt M1911 A1 CO2 Blowback Airsoft Pistol will perform like all the others KWC pistols I have tested before it.
In yet another Field Test Shooting Review I test out an Cybergun distributed KWC made CO2 powered Blowback 6mm Plastic BB shooting Sig Sauer P226 X-Five Pistol. I have already done some table top Reviews for a few other versions of this same KWC made pistol... The 4.5mm Steel BB shooting version of this same Cybergun distributed pistol and also the KWC unlicensed version in Airsoft and with some slightly different cosmetics.
Getting to the Field Test shooting portion of this review. I performed my standard five round Chronograph velocity fps test using .20 gram plastic Airsoft BB's with a brand new 12 gram CO2. The fastest Airsoft BB achieved by the Cybergun KWC Sig Sauer P226 X-Five CO2 Blowback Airsoft Pistol was 327 fps and the slowest came in at 298 fps with a five shot average of 312 fps, that might seem low but in terms of a close range Airsoft gun this is ideal.
Next up in my Field Test Shooting Review was my target test, and like always, I set up 30 feet back shooting from a semi-rested position (Sand bag up front and standing in the back). This shooting position provides a nice and stable shooting platform to get a good idea on the overall accuracy I should be able to expect with the Cybergun KWC Sig Sauer P226 X-Five CO2 Blowback Airsoft Pistol. Of course the results are a little dependant on how I'm shoot on the day of my testing :)
I shot 10 rounds through my Cybergun KWC Sig Sauer P226 X-Five CO2 Blowback Airsoft Pistol and they all easily found their mark close together on the paper target, 8 of the 10 shots grouped within a 3/4 inch hole with 2 shots coming out juts a bit extending the grouping to about 2-3 inches. With light Airsoft BB's some shots will stray a little bit but the fact that 8 out of the 10 shots pretty much made one small hole shows that this Blowback Airsoft Pistol is very accurate to say the least.
The Cybergun KWC Sig Sauer P226 X-Five CO2 Blowback Airsoft Pistol has an awesome single action trigger, if your not ready for it it can almost get away on you but after a couple of shots you will easily figure out the break and release points and be hitting targets down range with ease from this super short and light trigger. The Cybergun KWC Sig Sauer P226 X-Five CO2 Blowback Airsoft Pistol does also have a double action trigger if you decide to lower the hammer but need to take a quick shot. The Blowback action is one of the heavier blowback actions you will find on an CO2 Blowback airgun and the gun itself is fairly large and a bit on the heavy side but at the same time really well balanced and a joy to shoot.
This Field Test Shooting Video Review focuses on the performance results of the Elite Force Blowback CO2 Airsoft Race Gun. I put it through its paces to see what kind of feet per second performance it can achieve using .20 gram Airsoft plastic BB's. I also perform my standard 10 shot accuracy test from a 30 foot back shooting position to see how this IPSC pistol groups on paper.
My first portion of the test, the fps velocity test I performed using my Chronograph shooting five .20 gram standard plastic Airsoft BB's with a brand new CO2. The fps for the Elite Force Blowback CO2 Airsoft Race Gun ranged from 343 to 366 fps with an average 5 shot reading of 357 feet per second. The temperature was not exactly warm on this day, just a little over 10 Degrees Celsius so I was not expecting top velocity from the Elite Force Blowback CO2 Airsoft Race Gun, even so at right around 350 fps this pistol would be perfect for close quarters Airsoft games.
Next on my Field Test Shooting check list was the accuracy portion of this review, I performed my standard 30 foot back paper target test using a semi-rested position, standing in the back with a sandbag up front to rest my hands on for stability. This position is nice and stable but not perfect so there is always some human factor to take into account and I would say I may have had a little too much caffeine on this day but I really don't think it would have made a difference as the Elite Force Blowback CO2 Airsoft Race Gun just did not want to settle down at all for me. Shots where all over the place but at least my red dot sight was relatively well centered since most shots landed on the paper. I would say I got around a 7 inch 10 shot grouping which by no means is great. I'm not even sure if the hop-up can be adjusted on this gun, if so it could improve the accuracy a bit, maybe even a different brand of Airsoft BB's could help since perhaps the fit of the Airsoft BB's I was using was not ideal?
I do have to say the trigger on the Elite Force Blowback CO2 Airsoft Race Gun is really nice, it is a true single action trigger with a fairly short take-up and a nice light release. You can really unload your magazine fast as you would expect to be able to do with an IPSC marketed pistol. The blowback is snapping and does give a nice feeling of recoil but is not overpowering which helps this pistol with follow up shots. I would like to try out some other brands of Airsoft BB's perhaps a bit heavier and perhaps a different diameter to see if I can find a brand that works better with the Elite Force Blowback CO2 Airsoft Race Gun since I really feel it has way more accuracy potential.
Propulsion: Green gas or 12 Gram CO2 dependant on magazine used.
Action: Blowback,Single action only.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 29 rounds.
FPS: 410-440 fps
Trigger Pull: The trigger pull on the KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine is pretty much exactly like a real Ruger 10/22, nice and short, not to light or heavy, crisp and single action only. If you already have a Ruger 10/22 and want to pickup this Airsoft version for some anytime shooting then you will not be disappointed in the trigger since it is already what you are used to.
Accuracy: I decided to setup my paper target a little further out than my standard 30 feet, so I took it back to around 50 feet and put around 24 shots into it in a fairly quick succession from a rested position. The KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine grouped continently and well centred on target getting around a 3 inch grouping. This was using a red dot scope but with the out of the box hop-up setting in place. I was a little bit surprised by my fps results as my Chronograph recorded an impressive 445 average 5 shot fps using the lower powered green gas magazine. All shot where within only a few fps of each other too! I can only imagine how hard this gun would shoot using the alternative CO2 Magazine. Blowback action was just enough to give some feedback and of course allowed for the bolt to cycle giving the KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine a true single action trigger pull.
Build Quality: The build quality for all KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine is very good with a nice weight and feel to it, It really does feel like I am holding a real Ruger 10/22 and it is one of the most popular semi auto 22LR rifles out there for a reason. Mechanically this Ryger 10/22 copy works great, super consistent and very responsive. The fit and finish as with all KJWorks guns is top notch.
Realism: The KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine is for all intents and purposes simple an Airsoft version of the Ruger 10/22 and even though I have no way to confirm this, I would imagine many 10/22 after market accessories may actually work with the KJWork 10/22 Gas Blowback Airsoft Carbine. Everything works just like it would on a real 10/22 without the loud noise and ejecting shells.
Built on the very popular 10/22 platform so lots of people are going to be very familiar with this rifle and may want an Airsoft version they can shoot just about any time they feel like it.
Good weight and feel to it.
Blowback semi auto action with true single action trigger.
Lots of rail access points for tons of add on accessories.
Pop-up fully adjustable sights stay out of the way but are ready to go when needed.
Easy to adjust Hop-up.
Available magazines in both CO2 and Green Gas.
Adjustable AR styled rear stock with AR pistol grips.
Sling mounts included.
Works with standard Airsoft screw on flash hider or suppressors.
Awesome FPS and consistency.
Very accurate even at 50 feet, around a 3 inch 25 shot grouping.
Cons:
No full auto mode.
Higher capacity mag would have been nice.
Would be nice to have a higher capacity magazine for it.
Comments:
I am really impressed with the KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine! It feel and shoots a lot like the real steel version but with less noise and recoil. For back yard shooting fun and practice you can not find a cheaper gun out there to simulate shooting your real 10/22 and of course this rifle used on an Airsoft field would be a perfect fir for almost any shooting environment since it is light, compact, accurate and powerful. I think I found my newest favorite Blowback Airsoft Rifle :)
My Vimeo Table Top Review of the KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine:
Action: Semi auto, single action only with blowback.
Ammunition Type: 6mm plastic BB's.
Ammunition Capacity: 16 round full size drop out magazine.
FPS: 370.
Trigger Pull: The Single Action Only trigger pull on the Umarex Elite Force Blowback CO2 Airsoft Race Gun is what you want when looking for a gun made specifically for IPSC styled shooting. The trigger is nice and light with a very short take up and crisp release. Exactly what you would be looking for when wanting to shoot accurately and quickly as in with IPSC competition shooting!
Accuracy: I have not done a field test or shooting video for the Umarex Elite Force Blowback CO2 Airsoft Race Gun so far, I am just waiting for the weather to get a little bit better but that should be soon! I woudl expect this pistol to get close to 400 fps on a warm day and pretty decent shots pre CO2 with its shorter blowback action and magazine design that seals the Airsoft BB in the breach. We will have to wait and see ot be sure...
Build Quality: The Umarex Elite Force Blowback CO2 Airsoft Race Gun is well built, it's pretty much entirely metal except for the grips and part of the full size magazine. It weighs in at a hefty 2.5 pounds so be prepared for a relatively heavy pistol but with good balance that will offset the weight of it. The tolerances are very good with very little slide wiggle the slide spring is nice and firm and the slide catch release seems to function really well, I like that the slide racking handle can be switched to either side of the gun depending on your shooting preference.
Realism: The Umarex Elite Force Blowback CO2 Airsoft Race Gun is not based on any one gun that I am aware of but overall looks the part of a real gun with all the working parts and features of a semi auto pistol of this type. You will find a full size drop out magazine is sprung to eject with force when you press the magazine release which is great for IPSC shooting. The slide catch/release will also lock the slide back on the last shot and with rails top and bottom you have several options for adding accessories.
All metal construction - good weight and very solid feeling gun.
Heavy snappy blowback action, good recoil spring tension.
Fit and finish is really nice.
Well balanced, so even with heavy blowback the gun should stay on target.
Really light, short and smooth single action trigger, for quick follow up shots.
Can take the sight rail off and install one of the two included adjustable open sight options.
Expect it to get a decent amount of shots per CO2 because of the limited blowback action and magazine design.
Would make a nice IPSC trainer.
Cons:
Comes with a red tip but may be able to take it off.
Not sure about the hop-up setup, believe it has hop-up but no way to adjust it that I could find.
Has that white waring instruction labeling on the slide, at least it is in very small print.
Comments:
Overall the Umarex Elite Force Blowback CO2 Airsoft Race Gun is a really nice competition shooting pistol and I am looking forward to getting some shooting time in with it to see if it performs as good as I believe it will. I am also hoping with it's slightly shorter blowback action and magazine design that not only will it get good fps but also a reasonable amount of shots per CO2. At this point I am not sure if am going to put a Red Dot on the sight rail or take the sight rail off and go with open metal sights, either way I pretty sure to expect fast and accurate shooting with this IPSC inspired Race Gun.
My Vimeo Video Review for the Umarex Elite Force Blowback CO2 Airsoft Race Gun:
Some more of my Personal airgun pistols for sale! I am showcasing here on the Replica Airguns website and over on the Replica Airguns YouTube channel a series of videos I am making for the purpose of selling some guns out of my personal collection. I simply have to make room for the new guns I will be testing and reviewing for everyone, my collection has gotten a little bit out of hand and needs to be thinned down a bit :)
In this 6th Mike's Personal Guns For Sale video, I am offering three of my Airsoft pistols, the super popular Dan Wesson 6 Inch Silver in pretty much brand new condition complete with the box, manual, speed loader and shells. I also have tow rather hard to get Airsoft guns that are in somewhat limited working condition and need a little TLC. But the simple fact that they are not easily obtained here in Canada does bring up their value a little bit.
Make sure to watch my above YouTube video to see these Airsoft Pistols I am selling and instructions on how you can take part in the sale and purchase of them. By the way I am only selling to Canadian residents since shipping cross borders is a little sketchy.
Here is a list of the Airsoft Pistols I am selling from my personal gun collection:
In this 2016 SHOT Show Interview I talk with Chip Hunnucutt from Crosman Corporation. Chip was eager to show off Crosman's new Airbow which is a essentially a hybrid PCP Air Rifles combined with a Crossbow. SO take away the bow and replace the power source with a 3000 PSI compressed air system that is capable of shooting standard archery arrows at 450 fps with 160 foot pounds of energy using 375 grain arrows.
The Crosman Airbow on a full 3000 PSI charge can deliver 8 consecutive shots @ the regulated 450 fps. The Airbow also weighs in at 7 pounds and being that it is a Bullpup design it is only 33.5 inches long so nice and compact for an arrow shooter.
Since the power is generated by the PCP compressed air system there is no heavy cocking rope so a simple lift of the ambidextrous cocking bolt is all that is needed to charge the Crosman Airbow. The Airbow also comes standard with a CenterPoint® 6x40 mm scope specially designed with the Airbow in mind.
Since the Crosman Airbow is technically an under 500 fps airgun, it should be considered an uncontrolled firearm here in Canada which means no PAL license will be required to buy and own the Crosman Airbow in Canada. In terms of using the Airbow for hunting as it is not a bow but rather an Airgun, that is yet to be determined here in Canada.
In this 2016 SHOT Show Interview I talk with Bob Li from Action Sport Games. Bob shows me some of the new products this year from ASG. Some of ASG's newer pistols are the Dan Wesson 715, the CZ 75 SP-01 Shadow, the CZ P-09. New to the rifle line is the CZ Bren 80, also a couple of sniper rifles, the M40A5 and M40A3. ASG is also coming out with a an Inferno HPA version of their CZ Scorpion EVO 3A1.
The ASG Dan Wesson 715 has ot me my favorite product from ASG, you need to hold it in your hand to really understand how solid this pistol really is at close to 3 pounds. Everything about it is an improvement over previous Dan Wesson models including the trigger and hammer action, crane setup and the more actuate frame length with the new more compact internal CO2 valve. The ASG Dan Wesson 715 will be shipping in 4.5mm Steel BB, 6mm Plastic Airsoft and .177 caliber pellet versions.
ASG's two new Full blowback CZ 75 SP-01 Shadow, the CZ P-09 pistols should be coming out shortly, both will be available in 4.5mm Steel BB and 6mm Plastic Airsoft. Both pistols feature a metal slide and frame with full size drop out metal magazines and will have CO2 and Green Gas magazine configurations. The CZ P-09 will have a threaded barrel and barrel protector.
This is my SHOT Show 2016 Teaser Video! You will get to see some new gun highlights from companies like Umarex, ASG, Crosman, Sig Sauer, KWA and ISC. I will be following up this video with some interview videos very soon so do make sure to check back for those uploads. All I can say about the show is it’s huge! So much to see, so much walking and too much to take in…
ASG:
As always, ASG had some new products this year. The all new Dan Wesson 715 357 Magnum shell loading Revolver! This gun feels absolutely amazing in the hand and will be available in Steel BB, Airsfot and even Pellet shooting versions. Also new are the CZ P-09 and CZ 75 SP-01 Shadow Full Blowback BB and Airsoft Pistols.
Crosman:
Big at Crosman this year was their PCP Airbow, Crosman put a lot of focus on this product and even had a lot of crossbows on display to go with their new PCP Airbow. Crosman also introduced their low cost entry level Benjamin Maximus PCP rifle in .177 and .22 calibers offerings. Not really much in the way of replica pistols from Crosman this year, but then again last year was kind of the same?
Sig Sauer:
I finally made it to the Sig Sauer Booth this year to checkout their new CO2 Pellet gun line. All new Sig Airguns are made true to size and weight with similar trigger actions as their real steel versions. The Sig MPX is their more compact (shorter barreled) pellet shooting CO2 rifle with internal blowback and belt fed 30 round magazine. The Sig MCX is the longer barreled rifle version but built much the same as the MPX. Sig also introduced two new pellet shooting CO2 Blowback Pistols, the P226 and the P250. Both use similar double ended rotary magazines as the Umarex PX4.
Umarex:
Umarex always seems to have some new exciting Airguns products to offer at SHOT Show. The PPK is back with a few updates including no more ugly CO2 tab sticking out of the bottom! And yes the Beretta Model 92A1 will finally be shipping soon, I believe in February! My favorite product this year from Umarex would have to be the Full Blowback, Full size drop out magazine S&W M&P 40 CO2 BB Pistol. Umarex released yet another 1911 on the market, this version does come with a stick mag and sports pretty high fps and more shots per CO2 then the KWC based 1911’s. The super popular Colt SAA Revolver is now available in a pellet shooting version with a rifled barrel :) Umarex had on display another low cost revolver, the ultra futuristic looking Brodax CO2 BB Revolver.
KWA:
KWA always has really nice high quality products to showoff at there booth each year, we may even start carrying some of KWA's products this year, fingers crossed on that one… New to the KWA line are some AEG rifles with simulated blowback action, I really liked the Blowback AEG AK they had on display. KWA also released a new Airsoft shell loading revolvers that had some of the nicest looking brass and aluminum shells. On display under a glass cover was a very solid Gas Blowback Thompson Machine-gun with real wood stock, it was absolutely gorgeous!
ISC:
ISC known for their top quality AEG internals, had their full line of high quality Airsoft rifles on display. And new this year to ICS was their first ever Airsoft pistol, the blowback BLE Alpha. The BLE should be out mid year and looked and felt really nice. The trigger on it was super short and light.
I have some really awesome Interview videos I’m working on, I will be uploading them shortly so stay tuned for those…
When I say Airguns, I am referring to pretty much all BB, Airsoft, Pellet, Paintball and even Blank guns for most of the topics listed here.
Do’s:
Treat your Airgun just like you would a real gun. If something goes wrong, perhaps the outcome will not be as severe but do you really want to take a trip down to your local emergency ward to get a BB or Pellet removed?
Always assume your airgun is loaded, for some reason it always seems those empty guns are the ones that do the most damage.
Be discrete, If it looks like a gun other people will think it is a gun so don’t flash your airguns around in public. Keep it in a case when transporting and shoot it in an area that will not alarm other people.
Always wear eye protection when shooting your Airgun. Do you really want to shoot your eye out? No Joke!
Be aware of your surroundings like windows, hard objects that could make your ammo bounce back at you. Make sure you are shooting your Airgun in a safe direction at all times, know your target and beyond.
Use Airguns to teach others and learn how to safely and effectively shoot a gun. Airguns can be less intimidating then a real gun (Not so loud and very little recoil) and make for great start out and transitions guns.
Use Airguns to get more inexpensive trigger time and become a more experienced shooter. Airguns cosy only pennies per round to shoot and can be shot in way more areas than a real gun can, practice makes perfect so get shooting!
Use Airguns in areas where real guns may not be allowed or safe to use. Again, Airguns can be shot in all kinds of places, in your back yard or even in a properly setup indoor home range.
Use Airguns with adequate power for safe and humane pest control where real guns may be prohibited.Airguns are quiet and less likely for the bullet to travel long ranges which makes them ideal for close range pest control in areas where real guns are too loud and to powerful.
Don’ts:
Do not assume because it is an airgun it is not dangerous or simply a toy. Many Deaths have been caused by Airguns along with a lot of pain and suffering so treat your Airgun with respect. It is not a toy or you would find them in the toy department at your local store along with yo-yos and stuffed animals.
Do not point or shoot at people unless of course you are using an Airsoft gun in an Airsoft field or facility. Yes Airsoft guns are meant to shoot at each other (with appropriate attire like eye protection and full body clothing), but steel BB and Pellet can cause serious injury especially at close range and on direct skin contact.
Do not leave your Airgun loaded, you never know who is going to come across it and accidentally discharge it. Remember, a loaded gun is a dangerous gun in the wrong hands. You may know better than to assume the gun is undulated but children and even adults without any gun training will most definitely handle the airgun without consideration of the danger it poses.
Do not use an Airgun for self protection. See my related video. Simply put, Airguns are not practical for self defense because they rarely have enough Stopping Power. The ones that do have enough power need to be pre-charged and in most cases are only single shot meaning if you miss or don’t get the job done no the first shot then you are done.
Do not use an underpowered Airgun for pest control. See related video. Using a low powered BB pistol for pest control is cruel, you will only injure the animal making it suffer unnecessarily. Use a high powered pellet rifle to get the job done.
Do not take your gun apart, in most cases this will void the warranty and the reality is that airguns rarely need to be cleaned since no dirty gun powder is used. lead pellet rifles may require occasional barrel cleaning to keep the rifled barrel free of debris.
Do not over oil your Airgun, a little goes a long way and too much oil will just attracted dirt, use the right airgun oil and just enough to keep part functioning smoothly.
Do not over pump an Airgun. Over pumping an Airgun can cause damage to valves and seals and in a worse case situation a rupture the air pressure reservoir or even cause the airgun to explode!
Can I use Airsoft BB's in my BB Pistol? I would have to say this is by far the number one question I get asked in the comments section of my Vimeo videos. I have made several videos where this question gets addressed within the video but so far to date I have not made a stand alone video just covering Airsoft BB use in BB Guns.
So here it is, and now I have a video I can link to this so very common question, if you where wondering about this yourself than please watch my YouTube Video on this topic as it goes into a fair amount of detail about it.
The short answer to this question is no, you can not use 6mm Airsoft BB's in a 4.5mm Steel BB Pistol or Rifle. For the simple reason that 6mm is larger than 4.5mm and so the physical diameter of a6mm Plastic Airsoft BB is just to large to fit inside of a 4.5mm Steel BB magazine or barrel.
People have commented about using a 4.5mm plastic Airsoft BB in a 4.5mm BB gun and yes this could in theory be an option but I discuss why I feel this is not a good idea based on size and mass.
With the popularity of the KWC - Cybergun 1911 Blowback CO2 Pistols and how super realistic they are in so many ways, it is no surprise that people often ask me if they can replace the original grips with grips made for a real 1911.
The short answer is yes you can! You will have to be prepared to remove just a little bit of material from the backside of both grips near the bottom of the handle where there is an area that has been flared out to accommodate the CO2. Not really a big deal, you can use a Dremel for the quick and easy approach or even some sand paper if you don't mind taking a little more time.
I'm getting close to uploading 600 videos now over on the Replica Airguns Vimeo channel, so there are bound to be a lot of similar questions and popular discussions. In this Replica Airguns Vimeo Video I address what I feel are my Top 10 Most Common Airgun Questions and Discussions.
