Power Sources Covered in this review: CO2 - Green Gas / Propane - Spring - AEG / AEP (Automatic Electric Gun - Airsoft Electric Pistol)
Pro’s:
CO2 Airsoft Guns allow for fast repeat shooting, great for action shooters, generally CO2 Airsoft Guns will have a little more power then Green Gas Airsoft Guns. There is no need to pump or cock your CO2 powered Airsoft gun in-between shots and a CO2 power source can allow for a very realistic action of the gun you are shooting.
Green Gas (Propane) Airsoft Guns operate much the same as CO2 Airsoft guns so they all make for great action shooters and the Green Gas powers the mechanical operation allowing for very realistic operation. Green Gas (Propane) Airsoft Guns can cost a little bit less to operate that a CO2 Airsoft Gun especially if you plan to use Propane as it can be cheaper to buy than the smaller 12 gram CO2 Cartridges.
Spring Airsoft Guns are generally fairly basic and low cost so they are the usually the most affordable Airsoft guns to buy. There is no need to buy CO2 or Green Gas or even a Battery and Charger Setup so the cost to shoot Spring Airsoft Guns is only going to be subject to the Airsoft BB’s you plan on buying.
AEG (Automatic Electric Guns) have the most consistent power as they use a spring internally that the electric motor draws back before each shot, the internal spring will essentially apply the same force to the Airsoft BB’s with each shot. AEG (Automatic Electric Guns) are a great option when you are wanting a Full Auto Airsoft gun since there is no cool down effect and as long as your batteries are charged and you have Airsoft BB’s in your magazine, the gun will simply keep shooting. AEG (Automatic Electric Guns) allow for the highest capacity magazines and often hold as many as 500 Airsoft BB’s in a single magazine. So if you’re looking for raw firepower an AEG or AEP Airsoft Gun is your best option. Once you have purchased your AEG (Automatic Electric Gun) and a battery and charger setup, they are fairly inexpensive to operate since no CO2 or Green Gas is required.
Con’s:
CO2 Airsoft Guns require the additional cost to buy the CO2 cartridges as they will not function without it. CO2 Airsoft Guns have a limited power output and lose power as you shoot and use up the CO2. CO2 Airsoft Guns are effected by hot and cold temperatures and will have less power in colder temperatures and may not even work in super cold environments. CO2 Airsoft Guns will have a more conservative ammunition capacity since too high of a capacity magazine would freeze up the magazine and even the gun.
Again since Green Gas (Propane) Airsoft Guns work much like CO2 Airsoft Guns, they are effected by cool down and lose power when shoot quickly or as the Green Gas or Propane runs low. Green Gas does not expand as much as CO2 so it will not be as powerful and even less effective in colder temperatures. Green Gas Airsoft Guns will have a more conservative ammunition capacity since too high of a capacity magazine would freeze up.
Spring Airsoft Guns are not the best action shooters since you need to manually operate the slide to pullback the spring prior to each shot, this does work well with Pump, Lever and Bolt Action Airsoft guns but is not the best option for pistols since most real steel pistols operate in semi auto mode.
If you plan to use your AEG (Automatic Electric Gun) in a battle then it will require a multi battery setup which does cost a bit more upfront. AEG (Automatic Electric Guns) are know to not operate as realistically as a CO2 or Green Gas Airsoft gun since CO2 and Green Gas Guns do allow for the same realistic mechanical operation which can give very believable blowback operation, this is hard to replica with an AEG Airsoft Gun.
Power Sources Covered in this review: CO2 - Spring Piston - Variable Pump -HPA (High Pressure Air)
Pro’s:
CO2 Airguns allow for fast repeat shooting, great for action shooters, generally CO2 Airguns will supply a medium power range. No need to pump or cock your CO2 powered weapon in-between shots and a CO2 power source can allow for a very realistic action of the gun you are shooting.
Spring Piston Airguns are best suited of single shot situations, they can provide low to high power output depending on the spring used. Spring Piston Airguns are very low cost to operate since you only need to buy the Pellets or BB’s. Spring Piston Airguns are not greatly effected by outside temperatures.
Variable Pump Airguns allow you to decide how much power your gun will have and can offer very high power output depending on the Airgun. Variable Pump Airguns are very low cost to operate since you only need to buy the Pellets or BB’s. Variable Pump Airguns are not greatly effected by outside temperatures. Variable Pump Airguns generally have very low recoil and vibration.
HPA (High Pressure Air) Airguns generally do not require pumping or cocking in-between shots and some even come in semi automatic or bolt action. HPA Airguns can have very high power output and even be used on larger game using large caliber ammunition. HPA Air Rifles have lower recoil and low vibration. HPA Airguns can be charged ahead off time so they are ready for use when you need them.
Con’s:
CO2 Airguns require the additional cost to buy the CO2 as they do not function without it. CO2 Airguns have a limited power output and lose power as you shoot and use up the CO2. CO2 Airguns are effected by hot and cold temperatures and will have less power in colder temperatures and may not even work in super cold environments.
Spring Piston Airguns require cocking before each shot. Spring Piston Airguns can have a lot of recoil and vibration, so much so that special optics must be considered when buying an optical sight. The action of the spring recoil can effect accuracy, especially if you are not use to the vibration and recoil or have spent some time practicing using a Spring Piston Airgun.
Variable Pump Airguns will require multiple pumps to achieved maximum power output which can take some time in-between shots. So you are going to have to work for each shot.
HPA (High Pressure Air) Airguns require the use of a manual pump to fill their built in air tank to maximum pressure and it does take a lot of time to manual fill an HPA tank. Alternatively you can have the air tank filled at a shop or buy a pressurization system similar to a scuba tank out paintball setup, the cost of this setup can be very high but will save you the castle of manually pumping air in to your HPA Airgun. HPA Airguns are generally a little more bulky then other Airgun systems since they have to accommodate fairly large air pressure tanks.
This is not to say that a “Real Gun” is not as good as an Airgun or better in other ways, in this video I’m just pointing out how an Airgun in some cases can actually be better suited than a Real Gun.
Availability: What I mean by this, is that in many countries Real Guns can be very hard to acquire and often require safety course and applications before one can purchase a Real Gun. I have no problem with this but it is a reality that must be considered. Having an Airgun versus not having a gun at all makes it a better option for people that live in countries that have strict gun laws. Here in Canada we are allowed Real Guns, even pistols but we do have restriction on our pistols and so I can only get certain guns in an Airgun version. As a collector this is better than not having the gun at all.
Price to Buy: Generally speaking you can pickup an enter level Airgun for much less money than a real gun.
Cost to Shoot: Real gun ammo prices have been steadily increasing to the point that a day out shooting can cost several hundred dollars just on the ammunition alone.
Comparison of Price:
50 rounds of 9mm ammo will cost around $18.00
6000 rounds of 4.5mm Steel BB will cost about $18.00
CO2 is a bit less than $1 per 12 gram Cylinder which can yield up to 100 shots each.
To shoot 100 rounds of 9mm will cost close to $40 versus 100 shots of 4.5mm steel BB at around $1.
For this reason alone an Airgun can make a lot of sense even for Real Gun owners looking to get more cost effective practice time.
Access to Shooting Locations: Depending on where you live you will have to consider your local laws and where you are allowed to shoot both types of guns but typically you can shoot an Airgun safely just about anywhere as long as you implement some backstop safety precautions. Here in Canada we can only shoot a pistol at designated gun ranges, where as Airguns have a lot more allowances to shot them as long as you are not braking any city bylaws.
Training Guns: Even if you plan to eventually step up to a Real Gun at some point, an airgun is a great option to first learn proper gun handling skills since if you where to make a mistake, the consequences are much less severe. Airguns are also a lot less intimidating than a real gun since they are much quieter and have less recoil, you don’t even need to wear ear protection with most Airguns which means an instructor can communicate to his pupil on the range a lot easier.
Prop Guns: Since Replica Airguns look so much like real guns these day, they can often be used as a safer substitute for use in Movie, TV or other Photo and Video productions. Using a Real Gun on set generally requires a certified “Gun Wrangler” be on hand as Real Guns must be transported, stored and handled using very strict regulations. Airguns generally do not need to follow the same rigid regulations that Real Guns are bound to.
Tactical Training with Live Targets: Obviously shooting a real gun at a live target would not fair well for anyone involved, so that is completely out of the question. Airsoft Airguns are however perfect for Tactical Training and other weapons based simulations. All that is required for safety when using Airsoft guns is the use of eye protection and generally some heavy clothing.
I am sure there are some more areas in which Airguns may have the advantage over a Real Gun but these are the main ones that I could think of.
In this Field Test Shooting video I test out the KJWorks KP-11 Hi-Capa 1911 CO2 Blowback Airsoft Pistol to determine what the real work velocity is and also how well it performs in terms of accuracy. To test velocity I use a my Chrony Chronograph and do my best to get 5 good readings which I then average out. I always use a brand new 12 gram CO2 cartridge and generally use .20 gram plastic Airsoft BB's for my entire Field Testing. To test accuracy I set myself up 30 feet back using a semi rested position, to do this I place a sand bag to rest my hand and gun on and then stand securely in the back while I place 10 rounds on a paper target. There is obviously some humane factor involved but I can usually get a good idea on how accurate a given gun is.
During the Velocity or Feet Per Second Chronograph testing, I did manage to get 5 good readings, not all in a row but all within the first 10 or so shots. The KJWorks KP-11 Hi-Capa 1911 CO2 Blowback Airsoft Pistol shot hard and averaged 420fps again using .20 gram Airsoft BB's.
For my accuracy testing, all 10 shots placed within about 3 inches and they where fairly well centered left to right but did shoot a little bit high, this could be corrected using the hop-up adjustment to bring the Airsoft BB's down just a little.
I was rather surprised at how loud the KJWorks KP-11 Hi-Capa 1911 CO2 Blowback Airsoft Pistol is, it is by far one of the loudest CO2 Pistols I have shot to date other than the Umarex Desert Eagle Pellet Pistol. The KJWorks KP-11 Hi-Capa 1911 CO2 Blowback Airsoft Pistol also has a lot of blowback kick which makes it a lot of fun to shoot. Don't expect a lot of shots per CO2 since it uses a lot of CO2 per shot but in my books it is worth it for the added blowback recoil.
The KJWorks KP-11 Hi-Capa 1911 CO2 Blowback Airsoft Pistol may shoot a little bit hot for indoor Airsoft close quarters games but if you plan to use it outdoors at longer ranges it would definitely send Airsoft BB's out to further away targets. You could also pickup a Green Gas Magazine to lower the FPS about 50fps or so which would calm the KJWorks KP-11 down enough for indoor shooting.
Action: Semi auto, single & double action with full blowback.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 25 round full size drop out metal magazine.
FPS: 366+ with extended barrel.
Trigger Pull: The trigger pull on the VFC FN Herstal FNX45 Tactical GBB Airsoft Pistol is surprisingly light in single action mode, there is also minimal takeup. When shooting in double action the trigger pull length is much longer and heavier and has a bit of a stickiness too it but since this is a blowback pistol most of your shooting will be in single action mode where the trigger feels great!
Accuracy: I haven't done a dedicated Field Test Shooting Video yet for the VFC FN Herstal FNX45 Tactical GBB Airsoft Pistol but I did get the chance to play around with it when I did my I.C.U. 2.0 HD Action Camera review. In terms of power and accuracy it feels pretty good and you can expect to get decent power and accuracy out of it, we will have to wait and see how it performs on paper targets and when tested on the Chrony.
Build Quality: The VFC FN Herstal FNX45 Tactical GBB Airsoft Pistol is well made overall, I have found pretty much all the VFC airguns I have gotten my hands on seem to be well made and very realistic. you will find metal parts where they would be on the real Steel version of this pistol and same goes for plastic parts like the frame in this case. The finish seems to be holding up nicely too for me.
Realism: VFC really seams to pay a lot of attention to every detail of their Airsoft guns and the VFC FN Herstal FNX45 Tactical GBB Airsoft Pistol is no exception. All the mechanical working parts on this Airsoft version work as they would on the real .45 ACP FN Herstal FNX45, even the extractor is a separate part not moulded into the slide like you would find on most Airsoft pistols. You also get Interchangeable Back Straps to accommodate different hand sizes and of course it's fully FN licensed!
Excellent reproduction of the real steel FN Herstal FNX45 in looks and operation.
Very Crisp Firm full blowback operation.
Excellent fit and finish.
Everything is Ambidextrous so great for lefties too.
High Rise sighs suitable for the addition of a moc suppressor.
Comes with two interchangeable internal barrel lengths.
Fully field strip-able.
Fully FN Herstal Licensed.
Cons:
Comes with a red tip.
Magazine is kind of shiny
My serial number plate fell off while shooting it so make sure yours is on tight.
Comments:
Like I have mentioned throughout this review, VFC not only makes super realistic Airsoft guns, they also make a really high quality product. The VFC FN Herstal FNX45 Tactical GBB Airsoft Pistol is another example of this and offers everything you would hope to expect in an Airsoft Replica! The only down side is the orange tip but that can be sorted out easy enough after you get it. It's definitely not a small gun so keep that in mind when deciding on buying it, overall the VFC FN Herstal FNX45 Tactical GBB Airsoft Pistol is a really nice Airsoft gun at a reasonable price point.
My Vimeo Video Review for the VFC FN Herstal FNX45 Tactical GBB Airsoft Pistol:
Trigger Pull: The trigger pull on the KJWorks KP-11 1911 is very good since it is modeled after a real steel 1911 which makes it short and crisp with a nice light trigger pull. There is a very slight take-up at the very beginning of the pull but once your get past this the release is crisp and predictable. Since it is not a double action trigger you will need to either rack the slide for your first shot or pull the hammer back if you have already chambered a round.
Accuracy: I have not done my actual Field Test Shooting video review for the KJWorks KP-11 M1911 Airsoft Pistol so I do not have any definitive feedback for you but based on my experiences shooting other KJWorks 1911 styled Airsoft CO2 Pistols I expect it to have great blowback action recoil, a nice trigger and good overall FPS and accuracy. In terms of reliability, KJWorks pistols are solid in this department.
Build Quality: As expected, the KJWorks KP-11 Hi-Capa 1911 CO2 Blowback Airsoft Pistol build quality is exactly like all the other KJWorks Airsoft guns I've tested so far, Build quality for the price point is top notch with tolerances between the moving parts like the slide and frame are extremely tight showing excellent workmanship and machining from KJWorks. The finish is always a step above other similar styled Airsoft and BB guns, youn really don't have to worry about the finish coming of as easy.
Realism: The KJWorks CO2 KP-11 Hi-Capa 1911 Blowback Airsoft Pistol copies the real steel very popular even today Colt 1911 45 caliber pistol, it can be field stripped very similarly to a real 1911 Semi Auto pistol and all parts function virtually the same including a working safety, grip safety, slide catch-release, magazine release and hammer. This Hi-Capa version has a more tactical look with a wider frame for what would be a double stack hi capacity styled magazine.
Has really good weight but not too heavy since it has a polymer frame..
Expect to have typical KJWorks crisp and firm full blowback operation.
Excellent fit and finish. I like the mat textured finish which looks to bed super durable.
Nice bright white dot sights, really easy to see.
I like the look of the tactical hammer and trigger.
Nice high capacity magazine with a little extra zing for the CO2 Mag.
Fully field strip-able.
Cons:
Is not really setup up for left handers with no real ambidextrous components.
CO2 magazine is long to accommodate the 12 gram CO2.
Grips may be a bit thick for smaller hands.
Comments:
I love 1911 pistols and enjoy shooting them, there is something about how they feel in the hand that is different form most other pistols. They always feel so solid. The KJWorks Airsoft versions capture that feeling exactly and again the little bit more you may pay for a KJWorks 1911 over some other lesser quality Full blowback 1911's is worth the cost in my books. This Hi-Capa 1911 version with it's tactical look and finish would make a great game player for sure!
My Vimeo Table Top Review of the KJWorks KP-11 Hi-Capa 1911 CO2 Blowback Airsoft Pistol:
I was personally confused about some of the similarities and differences between several models of KJWorks Beretta M9 CO2 Blowback Airsoft Pistols, so I decided to make a video where I go over 4 models of KJWorks M9 Pistols and point out the commonalities and differences between them.
Here are the 4 versions of KJWorks Beretta M9 CO2 Blowback Airsoft Pistols:
All of them come with interchangeable 25 round CO2 Magazines.
All of them shoot around 360+ fps.
All have a metal slide and frame.
All weigh close to the same weight (2.1 - 2.4 pounds).
All shoot in single and double action.
All have ambidextrous safeties.
All have white dot sights.
Prices range from $184 -$200.
Here is a list of the differences between them:
The VE, Vertex and M9A1 come in a semi gloss finish while the Tactical is more of a matt black.
The VE and M9A1 have rails for accessory attachments while the Vertex and Tactical do not.
The Vertec, Tactical and M9A1 have laniard loops while the VE does not.
Some slight trigger guard differences between the models but very subtle.
The Vertex and M9A1 share the same style classic Beretta pistol grip, The Tactical has a tactical finger pistol grip and the VE has it’s own unique pistol grip.
Make sure to watch my Vimeo video where I cover this information in detail:
Another Airsoft Pistol Preview Video to share with everyone. First up we have a nice lighter weight CO2 powered 1911 from KJWorks called the KP-11 The lower receiver is polymer which helps to keep this gun a little bit lighter all around but it still has good weight to it coming in at a little over 2 pounds, the grips are larger than some 1911's since the KP-11 has a double stack style full size drop out metal magazine. You will also find some nice Tactical upgrade like adjustable white dot sights, a lower rail for accessories and milled trigger and hammer.
I also show off an interesting and not all that common pistol from Cybergun, the FNX -45 Tactical in Gas Blowback. For import into Canada it ships with a longer barrel which stick out of the front of the gun but it also comes with a shorter barrel you can install after your receive it. The Longer barrel gives the Cybergun FNX -45 Tactical Airsoft Pistol the extra velocity to allow it to be Canada import ready. The FNX -45 Tactical is a really detailed and well built Airsoft Pistol. By the way the FNX -45 Tactical is also availabl in Dark Earth color.
Here are some of the specifications for the KJWorks KP-11 and Cybergun FNX -45 Tactical Airsoft Pistols:
Propulsion: Green gas or 12 Gram CO2 dependant on magazine used.
Action: Blowback,Single action only.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 29 rounds.
FPS: 410-440 fps
Trigger Pull: The trigger pull on the KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine is pretty much exactly like a real Ruger 10/22, nice and short, not to light or heavy, crisp and single action only. If you already have a Ruger 10/22 and want to pickup this Airsoft version for some anytime shooting then you will not be disappointed in the trigger since it is already what you are used to.
Accuracy: I decided to setup my paper target a little further out than my standard 30 feet, so I took it back to around 50 feet and put around 24 shots into it in a fairly quick succession from a rested position. The KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine grouped continently and well centred on target getting around a 3 inch grouping. This was using a red dot scope but with the out of the box hop-up setting in place. I was a little bit surprised by my fps results as my Chronograph recorded an impressive 445 average 5 shot fps using the lower powered green gas magazine. All shot where within only a few fps of each other too! I can only imagine how hard this gun would shoot using the alternative CO2 Magazine. Blowback action was just enough to give some feedback and of course allowed for the bolt to cycle giving the KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine a true single action trigger pull.
Build Quality: The build quality for all KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine is very good with a nice weight and feel to it, It really does feel like I am holding a real Ruger 10/22 and it is one of the most popular semi auto 22LR rifles out there for a reason. Mechanically this Ryger 10/22 copy works great, super consistent and very responsive. The fit and finish as with all KJWorks guns is top notch.
Realism: The KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine is for all intents and purposes simple an Airsoft version of the Ruger 10/22 and even though I have no way to confirm this, I would imagine many 10/22 after market accessories may actually work with the KJWork 10/22 Gas Blowback Airsoft Carbine. Everything works just like it would on a real 10/22 without the loud noise and ejecting shells.
Built on the very popular 10/22 platform so lots of people are going to be very familiar with this rifle and may want an Airsoft version they can shoot just about any time they feel like it.
Good weight and feel to it.
Blowback semi auto action with true single action trigger.
Lots of rail access points for tons of add on accessories.
Pop-up fully adjustable sights stay out of the way but are ready to go when needed.
Easy to adjust Hop-up.
Available magazines in both CO2 and Green Gas.
Adjustable AR styled rear stock with AR pistol grips.
Sling mounts included.
Works with standard Airsoft screw on flash hider or suppressors.
Awesome FPS and consistency.
Very accurate even at 50 feet, around a 3 inch 25 shot grouping.
Cons:
No full auto mode.
Higher capacity mag would have been nice.
Would be nice to have a higher capacity magazine for it.
Comments:
I am really impressed with the KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine! It feel and shoots a lot like the real steel version but with less noise and recoil. For back yard shooting fun and practice you can not find a cheaper gun out there to simulate shooting your real 10/22 and of course this rifle used on an Airsoft field would be a perfect fir for almost any shooting environment since it is light, compact, accurate and powerful. I think I found my newest favorite Blowback Airsoft Rifle :)
My Vimeo Table Top Review of the KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine:
Materials: Mostly plastic with some metal construction.
Weight: 1.3 pounds (586 grams).
Barrel: 5.5 inches, non-rifled.
Propulsion: 12 gram CO2.
Action: Revolver, single & double actions.
Ammunition Type: 4.5mm steel BB's.
Ammunition Capacity: 10 rounds.
FPS: 375.
Trigger Pull: The trigger pull on the Umarex Brodax CO2 BB Revolver is actually rather nice. If you decide to cock the hammer back and shoot it single action style then you get a little bit of that SAA Revolver like ratcheting sound. The trigger pull in single action mode is short with virtually no take-up and on the light side. Double action shooting with the Umarex Brodax CO2 BB Revolver is not overly long or heavy either so action shooting is totally possible with this BB shooting CO2 revolver.
Accuracy: I can not comment so far on the shooting performance for the Umarex Brodax CO2 BB Revolversince I have not shot it yet. The weather is getting nicer outside so that should happen pretty soon. The claimed FPS for the Umarex Brodax CO2 BB Revolver is stated at only 375 which I find seems a bit low for a none blowback fairly straight forward BB pistol with an almost 6 inch barrel so hopefully my testing shows performance up into the 400's which I am hoping for. The open sights are non adjustable but there are tons more options by taking advantage of the two rails top and bottom for adding either a red dot or laser to increased target shooting ability.
Build Quality: The Umarex Brodax CO2 BB Revolver is pretty much an all metal pistol with the outer shell being made up of plastic, there is a fair bit of internal metal going on along with the trigger, hammer and of course the inner barrel made out of metal parts. Mechanically the Umarex Brodax CO2 BB Revolver feels solid and even though it only weight in at 1.3 pounds it feels much heavier in the hand.
Realism: The Umarex Brodax CO2 BB Revolver as far as I know is not an exact replica of any real steal gun currently in production. It's basically a spin off of an ultra tactical .44 magnum revolver with a super beefed up front barrel assembly sporting all kinds of accessory option to be placed on the top and bottom rails. I like that Umarex made sure to recess the barrel opening so it has a more realistic barrel size. Like many new CO2 airguns coming out these days the CO2 is not only well hidden inside the grips but a handy Allen key is built into the handle.
Not the heaviest revolver on the market but it feels really nice in the hand and has good balance, the weight is not bad at all and feels heavier than 1.3 pounds.
Trigger action is really good in both single and double action, short light single action trigger and totally usable double action trigger.
CO2 is well hidden with built in Alan key in the handle.
Rails top and bottom for all kinds of accessory add on options.
Barrel is recessed for that larger caliber look.
Nice and discreet safety.
Comes with three 10 shot easy to load rotary magazines.
Low cost with high fun factor.
Cons:
Grips are a bit hard to remove to get at the CO2, may work-in over time?
All black sights are not great on dark backgrounds and are non adjustable.
Would have liked to see fps into the 400 range.
Comments:
The Umarex Brodax CO2 BB Revolver when I first picked it up did not appeal to me all that much, maybe knowing it was for the most part yet another mostly plastic BB revolver with those thin pop in disc magazines didn't help me take notice much. But as I have been playing around with the Umarex Brodax CO2 BB Revolver it has grown on me a lot. I think it has a really cool look that is also very usable in terms of putting juts about any accessory you want on this CO2 revolver. The hammer and trigger action are also both excellent for not juts an inexpensive Airgun but even a higher end airgun. And right out of the box, or should I say clam-shell plastic wrap, you get three rotary disc magazines which is a nice bonus.
My Vimeo Table Top Review for the Umarex Brodax CO2 BB Revolver:
Some more of my Personal airgun pistols for sale! I am showcasing here on the Replica Airguns website and over on the Replica Airguns YouTube channel a series of videos I am making for the purpose of selling some guns out of my personal collection. I simply have to make room for the new guns I will be testing and reviewing for everyone, my collection has gotten a little bit out of hand and needs to be thinned down a bit :)
In this 6th Mike's Personal Guns For Sale video, I am offering three of my Airsoft pistols, the super popular Dan Wesson 6 Inch Silver in pretty much brand new condition complete with the box, manual, speed loader and shells. I also have tow rather hard to get Airsoft guns that are in somewhat limited working condition and need a little TLC. But the simple fact that they are not easily obtained here in Canada does bring up their value a little bit.
Make sure to watch my above YouTube video to see these Airsoft Pistols I am selling and instructions on how you can take part in the sale and purchase of them. By the way I am only selling to Canadian residents since shipping cross borders is a little sketchy.
Here is a list of the Airsoft Pistols I am selling from my personal gun collection:
When I say Airguns, I am referring to pretty much all BB, Airsoft, Pellet, Paintball and even Blank guns for most of the topics listed here.
Do’s:
Treat your Airgun just like you would a real gun. If something goes wrong, perhaps the outcome will not be as severe but do you really want to take a trip down to your local emergency ward to get a BB or Pellet removed?
Always assume your airgun is loaded, for some reason it always seems those empty guns are the ones that do the most damage.
Be discrete, If it looks like a gun other people will think it is a gun so don’t flash your airguns around in public. Keep it in a case when transporting and shoot it in an area that will not alarm other people.
Always wear eye protection when shooting your Airgun. Do you really want to shoot your eye out? No Joke!
Be aware of your surroundings like windows, hard objects that could make your ammo bounce back at you. Make sure you are shooting your Airgun in a safe direction at all times, know your target and beyond.
Use Airguns to teach others and learn how to safely and effectively shoot a gun. Airguns can be less intimidating then a real gun (Not so loud and very little recoil) and make for great start out and transitions guns.
Use Airguns to get more inexpensive trigger time and become a more experienced shooter. Airguns cosy only pennies per round to shoot and can be shot in way more areas than a real gun can, practice makes perfect so get shooting!
Use Airguns in areas where real guns may not be allowed or safe to use. Again, Airguns can be shot in all kinds of places, in your back yard or even in a properly setup indoor home range.
Use Airguns with adequate power for safe and humane pest control where real guns may be prohibited.Airguns are quiet and less likely for the bullet to travel long ranges which makes them ideal for close range pest control in areas where real guns are too loud and to powerful.
Don’ts:
Do not assume because it is an airgun it is not dangerous or simply a toy. Many Deaths have been caused by Airguns along with a lot of pain and suffering so treat your Airgun with respect. It is not a toy or you would find them in the toy department at your local store along with yo-yos and stuffed animals.
Do not point or shoot at people unless of course you are using an Airsoft gun in an Airsoft field or facility. Yes Airsoft guns are meant to shoot at each other (with appropriate attire like eye protection and full body clothing), but steel BB and Pellet can cause serious injury especially at close range and on direct skin contact.
Do not leave your Airgun loaded, you never know who is going to come across it and accidentally discharge it. Remember, a loaded gun is a dangerous gun in the wrong hands. You may know better than to assume the gun is undulated but children and even adults without any gun training will most definitely handle the airgun without consideration of the danger it poses.
Do not use an Airgun for self protection. See my related video. Simply put, Airguns are not practical for self defense because they rarely have enough Stopping Power. The ones that do have enough power need to be pre-charged and in most cases are only single shot meaning if you miss or don’t get the job done no the first shot then you are done.
Do not use an underpowered Airgun for pest control. See related video. Using a low powered BB pistol for pest control is cruel, you will only injure the animal making it suffer unnecessarily. Use a high powered pellet rifle to get the job done.
Do not take your gun apart, in most cases this will void the warranty and the reality is that airguns rarely need to be cleaned since no dirty gun powder is used. lead pellet rifles may require occasional barrel cleaning to keep the rifled barrel free of debris.
Do not over oil your Airgun, a little goes a long way and too much oil will just attracted dirt, use the right airgun oil and just enough to keep part functioning smoothly.
Do not over pump an Airgun. Over pumping an Airgun can cause damage to valves and seals and in a worse case situation a rupture the air pressure reservoir or even cause the airgun to explode!
Can I use Airsoft BB's in my BB Pistol? I would have to say this is by far the number one question I get asked in the comments section of my Vimeo videos. I have made several videos where this question gets addressed within the video but so far to date I have not made a stand alone video just covering Airsoft BB use in BB Guns.
So here it is, and now I have a video I can link to this so very common question, if you where wondering about this yourself than please watch my YouTube Video on this topic as it goes into a fair amount of detail about it.
The short answer to this question is no, you can not use 6mm Airsoft BB's in a 4.5mm Steel BB Pistol or Rifle. For the simple reason that 6mm is larger than 4.5mm and so the physical diameter of a6mm Plastic Airsoft BB is just to large to fit inside of a 4.5mm Steel BB magazine or barrel.
People have commented about using a 4.5mm plastic Airsoft BB in a 4.5mm BB gun and yes this could in theory be an option but I discuss why I feel this is not a good idea based on size and mass.
I don't often review target and or hunting rifles since for the most part Replica Airguns is all about well... replica airguns :) I have reviewed some of my own personal spring piston and pump rifles since I have them and there is a cross over in folks that like both the replica airguns and airguns meant for target and or hunting purposes.
We do have a small selection of spring piston rifles in our Replica Airguns Canada store suitable for target and small game so I thought I would point some of them out in this preview video.
Ammunition Capacity: 15 round full size metal magazine.
FPS: 300+
Trigger Pull: The trigger pull on the ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol is I would have to say one of the nicest 1911 single action triggers I have tested so far. The take-up is very slight with an extremely light trigger pull required to release the hammer. Any lighter and I would say it would be too light and perhaps prone to accidental firing.The three hole tactical trigger extends out a little further than some 1911's but feels secure on the finger.
Accuracy: At this point I have not shot the ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol but have high expectations based on the overall quality of this pistol and form other reviews I have read on this Airsoft 1911 replica. According to the manufacturers claimed fps, we should get somewhere right around 300 fps. The ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol has an adjustable rear sight for windage and we can take care of elevation using the adjustable hop-up so zoning in the Socom Gear US Marine MEU SOC 1911 to shoot dead center on target should not be too difficult.
Build Quality: The ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol is one of those Airguns that really catches your eye, and once you pick it up and hold it in your hands you discover that not only does it look really great but it also feels really great in your hands! The tolerances of the parts are excellent, everything mechanical is smooth without any friction and you can even see the texture of the metal grain through the quality matt black powder finish.
Realism: The ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol is a a fantastic replica of a real steel MEU SOC 1911 used by the US Marine Corps' Marine Expeditionary Unit (MEU). The balance and weight really make this 1911 Airsoft pistol feel like your holding the real deal, all the mechanic parts function as they would compared to the original and the ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol is fully field stripable.
Excellent quality, durable black powder coat matte finish .
Enhanced Pro-Grip with brass marine inserts
MEU SOC 1911 Licensed.
Three hole tactical trigger with skeleton hammer.
Comes in a hard shell case with Gemtech Outback II 5-inch silencer and lanyard.
Rail for adding accessories.
Cons:
FPS is kind of low for Canada Market so not one we can regularly get in stock.
A bit on the pricy side.
No option of CO2 magazine.
Comments:
With all the BB and Airsoft 1911's out there what makes the ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol stand out from the rest. First off it feel the most believabel when holding it in your hand, it seems ot have that perfect weight and balance that is often hard to replicate in an Airgun. With features like enhanced Pro-Grips with brass marine inserts, MEU SOC 1911 licensing, three hole tactical trigger, ambidextrous safety, super smooth and light single action trigger, White dot adjustable sights and the included hard shell case with lanyard and Gemtech silencer you can not go wrong with the ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol.
My Vimeo Video Review for the ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol:
During this Field Test Shooting Review Video I test out the ASG - Marushin Chrome Derringer 6mm Gas Airsoft Pistol by shooting some rounds through the Chronograph to get an idea on how powerful it really is. I also step back 30 feet and place some rounds down range on my paper target to see just how accurate this little surprise double shot Airsoft pistol is.
In terms of power, all I had to go on was the factory claimed power rating of .6 joules. So I filled up the ASG - Marushin Chrome Derringer 6mm Gas Airsoft Pistol with Propane gas, loaded two .20 gram BB's and shot them both one after the other though my Chrony. I did find that topping up the gas was necessary between loading this gun as the gas chamber is very small. You will only get three shots out of a fill but the last shot is really slow.
I did find that I consistently got right around 250 fps on the fist shot and pretty much bang on 200 fps for the follow-up shot. Not super fast but fast enough to hit a small paper target 30 feet away pretty much every shot. Shooting 6 rounds on my paper target from 30 feet back using a semi rested position I was able to get 5 out of 6 shots pretty well placed on my paper target. I am not sure what happened to the 6th shot but it seemed to hook really hard to the right, perhaps the Airsoft BB was deformed? My 6 shot grouping with the excepting of the one shot that went MIA ended up being about 5 inches, not bad for such a small little low fps pistol.
So in terms of usefulness what can you expect from the ASG - Marushin Chrome Derringer 6mm Gas Airsoft Pistol? Well you are for sure not going to be sniping anyone with it but it could for sure come in handy as a surprise back for your backup gun!
Action: Over-under double barrel single action only.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 2 rounds.
Energy: .6 Joules.
Trigger Pull: The trigger pull on the ASG - Marushin Chrome Derringer is single action only so you will have to cock the hammer separately for each of the two shots. The action of the single action trigger is extremely short with virtually no take-up to speak of. The trigger pull is also very light.
Accuracy: This part of the review is yet to be determined as I have not done my Field Test or Shooting tests for this pistol. I will put a link in here when I have done my official Field Shooting Test. I have done a little bit of playing around with the ASG - Marushin Chrome Derringer 6mm Gas Airsoft Pistol and can say it is not going to be the most accurate or powerful gun out there but that's not really what this ultra compact gun is meant for, more of a surprise, hey where did that come from kind of gun!
Build Quality: The ASG Chrome Derringer 6mm Gas Airsoft Pistol is built by Marushin and as a Japanese based company it is going to be mostly plastic but with that said this little pistol is built really well, the mechanical parts that need to be metal are, like the grips hammer, trigger, safety and many of the pins and screws. Everything is tight and the tolerances are excellent. The finish is also pretty much flawless.With the added metal parts this .5 pounds pistol actually feels pretty solid in the hand and it's hard to tell so much of it it is actually plastic.
Realism: The ASG - Marushin Chrome Derringer 6mm Gas Airsoft Pistol looks the part of a real steel Derringer in terms of size and mechanical parts all functioning as they would. Even the over-under barrels are recessed to look like a much larger caliber than 6mm. The only real give away would be the small gas valve located under the handle and of coursee the lighter weight.
Not a lot of meat parts but the metal grips, hammer, trigger and safety seem to add enough weight to make this Derringer feel pretty solid in the hand.
Nice recessed over-under barrels.
Mechanical part feel solid and tight.
Cons:
Main gun build is plastic, typical of Marushin guns.
Not a lot of power from my preliminary testing.
Only 2 shots so make them count!
Comments:
The ASG - Marushin Chrome Derringer is a rather unique 6mm Gas Airsoft Pistol and is not going to make a very good primary weapon or for that matter even a good secondary weapon, but on that off chance you want surprise on your side then this little guy would make a really great last resort gun for when you only have that one shot up close and personal and it's now or never... There's also the fact that it's a Derringer and how cool is that!
My Vimeo Table Top Video Review for this ASG Chrome Derringer 6mm Gas Airsoft Pistol:
In this Field Test Shooting video I test out the performance of the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol using my Chronograph to get a real world (FPS) Feet Per Second rating. I also position myself 30 feet back and shoot 10 rounds at a paper target using a semi-rested shooting position (Sand bag up front and standing in the back).
In terms of velocity the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol shot a bit on the fast side at 414 FPS when averaging a 5 shot strong using .20 gram BB's with a brand new CO2. Keep in mind I was using the CO2 magazine which will have more power than the Gas Magazine version. I would assume the Gas mag version would shoot right around the mid 300's which may be more suited for indoor Airsoft games. For outside Airsoft wars you may want the extra power of the CO2 mag for shooting at targets further distances out.
Stepping back 30 feet and shooting at my paper target, the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol produced a decent 2 inch 10 shot grouping that was just a hair low but well centered left and right. The low factor could be adjusted up using some Hop-up tweaking. The trigger in single action mode is light and the release is crisp. Even the double action trigger is fairly light for double action, but there is a lot more take up since your finger is doing all the work that the blowback action would normally do for you when shooting in single action.
With the heavy blowback and high FPS the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol creates a really great shooting experience. It would be great for some target practice, getting some additional trigger time in if you are a Sig Sauer P226 owner and would make an excellent outdoor Airsfot war backup weapon. The quality is excellent and as a lover of the Sig Sauer lineup of guns I highly recommend this Airsoft pistol from KJWorks.
Trigger Pull: The trigger pull on the KJWorks KP01-E2 Sig Sauer P226 Airsoft Replica is good in both single and double action. Once the slide is pulled back and released the first round is chambered and the hammer will remain back placing the KJWorks P226 in single action mode, the pull is light and the take-up is nice and short, most of your shots will be in single action mode unless you use the de-cocker to lower the hammer for a subsequent double action follow-up shot, double action shots are still pretty light but much longer in order to cock the hammer back.
Accuracy: (I have not shot the KJWorks distributed CO2 Mag version but I have already done a Field Test Shootinng Review for the same KJWORKS gun distributed and licensed by Cybergun in the Gas Mag version. Here is what I had to say about the Cybergun Gas Magazine version: "Shooting the Cybergun Sig P226 from 20 feet out in semi rested position I was able to get very good results. I placed 10 rounds in about 1.5 inches with the shot placement being a bit low possibly due to my barrel mod, adjusting the hop-up may bring the aim point back up to where it should be. The Sig Sauer P226 Airsoft Replica shot right around the 316 fps range while conducting my 5 shot average chrony testing which was lower than advertised but I was using much heavier .20 gram BB's. You can expect to get a full magazine worth of shots out of each gas fill-up but I did notice that as the magazine got colder it did tend to become much less efficient and also seemed to vent a lot of vapor."
Build Quality: The build quality for all KJWorks guns in my opinion is one of the best in the business. Fit and finish is top notch with close tolerances in the working parts as you would find in a real steel gun. The paint is excellent and in general will wear much better than other Airsoft guns out there. The KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol is pretty much all metal and feels it, the recoil spring is nice and firm and all working parts are smooth and crisp when operated.
Realism: The KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol is a replica of the real steel Sig Sauer P226 with the exception of the licensing. The KJWorks KP01-E2 really is a great looking and functioning Airsoft Replica. You can field strip this gun exactly like a real Sig Sauer and all the mechanical parts work just the same including a working de-cocker and adjustable front sight. It is really hard to distinguish the Airsoft version from the real Sig P226 in both looks and feel.
All metal pistol with good overall realistic weight to it.
Very crisp and firm full blowback operation.
Some of the best fit and finish in the industry. Especially in price range.
Nice accurate looking and working Sig Sauer P226 Replica.
Working de-cocker.
White dot sights for quick target acquisition.
Front sight is adjustable for windage.
Full size drop out magazine holds Airsoft BB's and CO2.
Fully field strip-able.
Cons:
No actual Sig Sauer Licensing but very clean look.
CO2 Mag does stick out a bit and add to size
Comments:
I am a huge Sig Sauer fan so I have kind of high expectations with a replica gun! The KJWorks lineup as a whole is really fantastic, and what I say about the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol can be said about the entire lineup. KJWorks makes a super well built product that replicates the real steal version almost exactly other then they shoot Airsoft BB's instead of actual bullets. When holding a KJWorks gun in the hand you can feel the quality, in weight, ballence and especially when operating the slide, trigger and other working parts. Everything just feels so perfect and responsive. For the money you can not go wrong with the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol or any other KJWorks gun for that matter.
My Vimeo Table Top Review of the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol:
This First Person Shooting Clay Pigeons Video with my KJWorks M9A1 and 1911 Airsoft Pistol is to serve two purposes: Number one and really the only reason needed to make a video like this... To get outside on a nice warm summer day and practice some tactile shooting all while recording it in first person so you can come along and enjoy it with me :)
Secondly I wanted to inform everyone that the video uploads will be a bit lighter for the next week or so since I am on what I call a working holiday. I am focusing on a Fitness Contest this weekend along with a Fitness Expo the following weekend, nothing to do with Replica Airguns but it does coincide with my other Website and YouTube channelGetFitOver40.com. The Fitness contest is the Victoria Cup where I will be competing in the Men's Physique (Masters - Over 40) and (Open - All Ages) divisions. The Fitness Expo is called "theFitExpo" and it is in Anaheim California.
So if you want to watch more of my videos then you will have to checkout my other fitness channel for the next week where I will be posting lots of related content on what's going on fitness wise in my life right now.
