View fullsize

Airguns are not toys and as so require proper storage, transportation and handling so as not to cause an accident that could be minor or even deadly.

No matter if you are handling an Airgun or a “Real Gun”, they should both be handled in the same manner even if the consequences from an accident with an Airgun may be less serious. Life long injuries like the loss of an eye are nothing to be taken lightly.

For the most part, what I talk about in this Airgun Safety 101 video can also be applied to a “Real Gun” although most countries will have stricter laws and guidelines in the storage, transportation and handling of “Real Guns” over an Airgun.

View fullsize

Storing Your Airgun:

In Canada an unregulated Airgun does not have any real specific safe storage guidelines but common sense should be used and I recommend that you at the bare minimum keep your Airgun in some sort of locked space whether it be a safe, cabinet or room that is locked all of the time.

You can also put a trigger lock on your Airgun if you do not have a lockable storage location for it.

You should also make sure to store your Airgun unloaded, at least when it comes to BB’s and or Pellets. If there is some unused CO2 in it, or it is charged with Compressed Air, but unloaded in terms of ammunition, that is OK, but again keep it in a safe location away from anyone that may be able to get their hands on it and hurt themselves or others.

View fullsize

Transporting Your Airgun:

Again, in Canada an unregulated Airgun does not have any real transportation guidelines but if you keep your Airgun out in the open and someone sees it, they will most certainly call the police and more than likely you may find yourself staring down the wrong end of a police firearm, at least until they sort it all out. This is very serious as unfortunately people have died as a result of handling their Airguns out in the open and underestimating what kind of police response that may entail.

For that reason alone, always keep your Airgun out of sight in a case or backpack or the trunk of your car. Never transport your Airgun loaded and it is best if you can lock it in a case or put a trigger lock on it for added safety when transporting it.

View fullsize

Shooting Your Airgun:

Shooting your Airgun is always the most enjoyable part of owning an Airgun, so don’t do something stupid and turn that experience into a nightmare. Treat your Airgun as if it is deadly at all times, never point it at anything you do not intend on shooting.

Keep your safety on until you are ready to shoot. Never put your finger on the trigger until you are ready to shoot it and only shoot it in a safe location with an appropriate background and backstop.

Think of the barrel of your Airgun as a light saber that if it crosses even your arm, it could cut it off. Even a BB to the arm is a serious matter. I had a friend that shot himself in the arm with a BB Gun and the BB lodged in the tendons of his wrist requiring an operation to remove it. He was a violin player so this could have ended his violin playing, but luckily he was OK.

When Your finger is not on the trigger it should be held across the trigger guard in a straight position to ensure no accidental misfires.

Wear eye protection, Steel BB’s will bounce back when they hit a hard surface and can come back with enough force to injure an eye easily. Generally Airguns do not require ear protection but some can be loud enough that you may want to wear some sort of ear protection as a precaution.

Only shoot with others that are responsible and take Gun Safety very seriously. Young people will need constant supervision and it is best to go through all of this first before even considering handing them an Airgun for the first time. Perhaps start them off with something like an Airsoft gun which will have less consequences if an accident were to take place.

Airguns are awesome in so many ways and allow for a similar shooting experience to a “Real Gun”. They can be used in more situations, with less overall cost and are a great way to learn proper gun handling and how to improve your shooting ability even if you are a “Real Gun” owner. Always be responsible with your Airgun not only for yourself but for others as it only takes a few idiots to ruin things for the rest of us. Don’t be that Idiot please!

• Buy Airguns in Canada

• Buy Airguns in the US

Many Canadians ask about options for what they perhaps could use for home defense since we are not allowed to really use any kind of a weapon to defend ourselves. A product classified as “Less Lethal” may be of interest to people living in Canada. I interviewed Byrna, just such a company that offers alternatives to standard “Lethal Interventions” for self protection and Josh from Byrna was kind enough to go over their pistol and rifle offerings specifically built to shoot paintball type ammunition for the purpose of stopping bad guys.

I am hoping this is a product we will be able to add to our online Replica Airgun Stores, as they do tick the boxes for import into Canada such as shooting well under 500 fps, yet having the ability to cause serious injury so as to allow them to be considered a non regulated firearm.

• Buy Replica Airguns in Canada

• Buy Replica Airguns in the US

View fullsize

In this Indoor Field Test Shooting Video I test out the Umarex T4E TR68 .68 Caliber Paintball Revolver to see what the real world velocity is and what kind accuracy I can get shooting at a paper target 30 feet away. For this Video Review I use a brand new CO2 along with .68 caliber Rubber Balls. I have already made a Table Top Video for the Umarex T4E TR68 so check that out if you’re interested in specifications and details along with more closeup video of this Paintball Revolver. And for fun I also made an interesting outside shooting video using actual Paintballs that highlights this Revolver along with the Umarex T4E HK VP9 .43 Cal. Paintball Pistol.

So let’s get straight to the shooting results! For my Chronograph test, being indoors the temperature was about room temperature, maybe a bit lower at around 19-20 Degrees Celsius or 66-68 Degrees Fahrenheit. Temperature can affect velocity as CO2 performs better in warmer conditions. My fastest Chronograph result was 205 fps while my slowest shot hitting 190 fps resulting in a average of 198 fps . Keep in mind the .68 caliber Rubber Balls have a lot more weight to them than the smaller .50 or .43 Caliber Balls used in other Umarex T4E Paintball Airguns.

View fullsize

Next I performed the accuracy portion which for me is the fun part, I often shoot 10 rounds in to my paper targets setup 30 feet down range, since the Umarex T4E TR68 .68 Caliber Paintball Revolver magazines only holds 5 rounds, I did have to make a quick magazine change half way through my Accuracy Test. I was also using a semi-rested shooting position with my hands resting on a sandbag up front and sitting on a stool in the back. There was also one other disruption in my shooting worth mentioning as I had to go up and put the paper target back on as it was dislodged by the energy of these larger Rubber Balls. That all said, I was able to get about a 5 inch grouping from my 10 rounds which is pretty good for a Paintball Airgun. I am confident you will be able to get all your shots on a body sized target at 30 feet out with a little bit of practice. Most of the shots were pretty well centered, perhaps just a little bit under the bullseye.

Even though the Umarex T4E TR68 .68 Caliber Paintball Revolver is a lot larger than the somewhat similar Umarex T4E TR50 .50 Caliber Paintball Revolver, I prefer it as I found it to shoot a bit more reliably and with good accuracy. It is maybe a bit large for some people as compared to the TR50 but I feel the extra size is worth it for the increased energy at point of impact and again the superior accuracy and reliability.

• Buy the Umarex T4E TR68 .68 Caliber Paintball Revolver in Canada

• Buy the Umarex T4E TR68 .68 Caliber Paintball Revolver in the US

View fullsize

Summer will be over before we know it, so why not get out and shoot some Paintball Pistols on a bunch of random targets in the yard before fall kicks in! I rarely get to use actual Paintballs in my Paintball Guns as I mainly test indoors and so I pretty much have to use Rubber Balls or have to deal with a bunch of clean up afterwards.

So today I grabbed my two newest Umarex T4E Paintball Pistols, the Umarex T4E TR68 and Umarex T4E HK VP9. I of course I loaded them up with their appropriate ammo .68 and .43 caliber Paintballs, and headed outside.

View fullsize

Figuring out how to make the video interesting and get lots of different camera angles can be fun, so I decided to grab my Hover Camera X1 which I think from now on is going to be my new “Camera Man” when I need a camera recoding me as I move around. I also placed my Insta 360 One R and my iVUE Vista Camera glasses in the mix. All being audio recorded with my Comica Vimo C Wireless Lapel Mic so you can actually hear everything clearly.

Seems like a lot of production using all of these recording devices and then having to line up, cut and mix everything together in post. Well you guys are worth it and I’m a bit of a tech junky so it was all kind of fun for me too.

• Buy Paintball Guns in Canada

• Buy Paintball Guns in the US

View fullsize

Type: Paintball Gun.
Manufacturer: Umarex - T4E.
Model: T4E TR68
Materials: Metal & Polymer.
Weight: 773 grams (1.7 pounds).
Barrel: 6.5 inches (165mm) ,Smooth bore.
Total Length: 13 inches (331mm).
Power Source: 1x12 gram CO2.
Action: Revolver - Double action only trigger.
Ammo Type: .68 Caliber Paintball or Rubber Ball.
Ammo Capacity: 5 Rounds x 3 magazines.
FPS: 230-300.

View fullsize

Trigger Pull: The trigger pull on Umarex T4E TR68 .68 Caliber Paintball Revolver is double action only but not very long with a much smoother feel than the TR50, so maybe Umarex did some improving here. without any ammo in it the T4E TR68 trigger feels responsive for a double action trigger. We will have to see when I do my Field Test Shooting Video how it performs and if fully loaded up and primed, if it feels the same?

Accuracy: So far I have not had the opportunity to test the Umarex T4E TR68 .68 Caliber Paintball Revolver out, the only other similar product that may compare would be the Umarex T4E TR50 but I have a feeling both these guns will perform rather different since the ammo is a lot larger on the TR68. Also with the way the different triggers feel, I expect this to help with performance on the Umarex T4E TR68.

View fullsize

Build Quality: The build quality of the Umarex T4E TR68 .68 Caliber Paintball Revolver is good overall. It is a mostly plastic build with some metal parts where they need to be internally. It is essentially two plastic halves held together by small screws with few actual mechanical working external parts. You have the trigger with its working trigger safety, the removable magazine and magazine release and of course the quick puncture CO2 screw knob. The hammer is internal. The Umarex T4E TR68 .68 Caliber Paintball Revolver is not very heavy but it does feel really solid in the hand because of its very large size.

Realism: The Umarex T4E TR68 .68 Caliber Paintball Revolver is not really a replica per say of any real steel gun that I know of. It does share a lot of similarities with the Crosman Vigilante which is a CO2 BB/Pellet Revolver with its main design going back several decades. The Umarex T4E TR68 .68 Caliber Paintball Revolver looks similar to what a modern looking large caliber revolver such as a 357 or 44 magnum looks like. It is not going to fool anyone up close that you actually have a real steel revolver but then again I don’t think if you are shooting it at anyone they are going to want to get all that close to you :)

View fullsize

Pros:

• Hoping to get a bit more raw energy out of the T4E TR.68 than the TR50 as it uses larger heavier ammo. (TR50 averaged 328 using rubber balls for reference).

• Lots of mounting options for accessories like a tac light, laser or other sighting option with it’s upper and lower picatinny rail setup.

• Quick CO2 pierce system so you can leave a CO2 in it ready to go any time with no worries about CO2 leaking out while in storage.

• Working Trigger Safety.

• White dot sights super easy to see on targets of varying colors and shades.

• DOA Trigger feels pretty decent, not too long or heavy.

• Comes with 3 total magazines you can preload ready for use.

• Super non-complicated design. Once loaded with CO2 and Paintballs or Rubber Balls, all you need to do is hit the CO2 knob and then pull the trigger.

• Build quality feels good, the gun is fairly beefy but not overly heavy.

• Grip is normal size even thought the gun itself is fairly large.

Cons:

• Mostly all plastic build.

• Sights are not adjustable so hopefully it is well centered out of the box.

• Do not expect a lot of shots per CO2. Will find out when I do my Field Test Shooting Review.

View fullsize

Comments:

The Umarex T4E TR68 .68 Caliber Paintball Revolver is an interesting Paintball gun, overseas versions are marketed as the HDR86 which stands for “Home Defense Revolver”, while the North American or Canada version is marketed as the TR68 for “Training Revolver”. This is mainly because in Europe most countries are not allowed to own real handguns but can own “Self Defense handguns”. In the US real handguns are very easy to obtain and can be used for self defense. Just across the border here in Canada we can not really purposely have on hand anything that we plan to use as a weapon for self defense so the Umarex T4E TR68 .68 Caliber Paintball Revolver, like the TR50 is marketed as a Training Revolver. What’s the difference? Not much, our North American 230+ fps version is a lot like the lower powered German versions in terms of power but you can also get more powerful versions in the UK. All that said, the Umarex T4E TR68 .68 Caliber Paintball Revolver at least here in Canada is made and marketed as a Training Paintball gun maybe not all that suitable on the field? What you decide to do with it is up to you.

• Buy the Umarex T4E TR68 .68 Caliber Paintball Revolver in Canada

• Buy the Umarex T4E TR68 .68 Caliber Paintball Revolver in the US

In this Replica Airguns Unboxing Video I take a look at 6 Airguns consisting of 2 Paintball Pistols, 3 Airsoft Rifles and one Pellet Rifle. This is not a full review in any way but is rather a preview of what i will be doing full Reviews for over the next several weeks.

View fullsize

Umarex T4E HK VP9 .43 Cal Paintball Pistol:

• Manufacturer: T4E Umarex

• Type: .43 Cal. Paintball Pistol

• Action: CO2 Blowback DOA

• FPS: 300+

• Ammunition Capacity: 8 Rounds

View fullsize

Umarex T4E TR68 .68 Cal Paintball Revolver:

• Manufacturer: T4E Umarex

• Type: .68 Cal. Paintball Revolver

• Action: CO2 Revolver DOA

• FPS: 300+

• Ammunition Capacity: 5 Rounds

View fullsize

Specna Arms Core SA-CO2 AEG Airsoft Rifle:

• Manufacturer: Spec Arms

• Type: .6mm Airsoft BB

• Action: AEG Semi/Full Auto SAO

• FPS: 410

• Ammunition Capacity: 450 Rounds

View fullsize

Bear River Black Ops SR4 AEG Airsoft Rifle:

• Manufacturer: Bear River

• Type: .6mm Airsoft BB

• Action: AEG Semi/Full Auto SAO

• FPS:400

• Ammunition Capacity: 300 Rounds

View fullsize

S&T Armament KAR 98K Spring Airsoft Rifle:

• Manufacturer: S&T Armament

• Type: .6mm Airsoft BB

• Action: Bolt Spring Action SAO

• FPS:400

• Ammunition Capacity: 11 Rounds

View fullsize

Beeman Black Panther Break Barrel Pellet Rifle:

• Manufacturer: Beeman

• Type: .177 & .22 Cal. Pellets

• Action: Break Barrel Spring Piston SAO

• FPS:495

• Ammunition Capacity: 1 Round

View fullsize

Cost:

Airguns are generally cheaper to buy and for sure cheaper to shoot. Airguns can cost as little as $50-100 to buy while real guns in similar models will cost many time more. Cost of ammo is so much less expensive than Real Gun ammo by a mile!

View fullsize

Difficulty to Obtain:

Airguns in most countries do not require any licensing or registration. Generally there are more available options in Airgun choices than Real Gun choices as restrictions often prohibit many Real Guns to be obtained.

View fullsize

Places to Shoot:

Unless you live in a super remote locations and your laws allow you to shoot Real Guns in those locations, then in most cases you can shoot an Airgun almost anywhere within reason. You can even shoot certain Airgun models in your basement. Airsoft is a great option for indoor shooting as the plastic ammo does not carry very much energy so with minimal effort you can make a backstop that will trap the ammo very well.

View fullsize

Trigger Time:

Because ammo is much less expensive and places you can shoot are easier to find, you can get a lot more Trigger Time under your belt which will also improve your shotgun with Real Guns and after all it’s just fun to shoot guns even if they are Airguns.

View fullsize

Safety:

I am not talking about safety in terms of protection. I am talking about safety as in if you do something stupid and your Gun goes off accidentally. If you accidentally fire your Airgun indoors, the bullet will not travel through floors or walls and potentially harm or kill someone on the other side. If you do manage to shoot yourself with an Airgun, the consequence are much less severe than shooting yourself with a Real Gun. That said, always treat an Airgun as if it was a Real Loaded Gun, as server injury and even death can occur even with an Airgun.

View fullsize

Ware Games and Training Situations:

There is no way you can use a standard Real Gun to shoot at people, unless extensively altered with special parts that make the Real Gun unusable to shoot live ammo. With Airguns you have the choice of using an Airsoft or Paintball gun that are both designed specifically for this purpose.

View fullsize

Pest Control:

If you have the need for pest control in an urban area where you do not want a stray bullet to travel too far or penetrate buildings if a shot where to go awry, then an Airgun designed for accuracy and power may be perfect for the job. Accuracy with target and hunting Airguns is on par if not better than many Real Guns and are have powerful enough to kill a pest humanely without having too much power for the job and having to worry as much about your background.

View fullsize

Prop Guns:

As mentioned already, Airguns can look a lot like Real Guns, so they are perfect to be used as a stand-in or Prop Gun when you need to simulate the look and function of a Real Gun. Again they are easier and cheaper to obtain and if something does go wrong, the consequences are much less severe.

View fullsize

Social Stigma:

Unfortunately Real Guns and perhaps any gun these days are looked upon with a social stigma as being the cause of the Crime rather than a tool used in a Crime. And so people blame Guns for these crimes rather than the people committing these crimes. If a person is motivated enough to do something bad, they are going to do it either way and will use whatever means is available to them to commit these Crimes. Including other means like: Knives, Blunt Objects, Poisons, Vehicles, Explosives… Sad but true! Airguns are not used in homicides or mass shootings as they are completely underpowered for a crime like this. They can however be used in crimes as a show of threat, as they do look a lot like real guns, generally people that use Airguns for real crimes, if challenged will give up immediately as they are completely outgunned. Don’t bring an Airgun to a Real Gun fight, you have better chance with a knife!

View fullsize

Type: Paintball Shotgun.
Manufacturer: Umarex - T4E.
Model: Umarex T4E HDB.
Materials: Metal & Polymer.
Weight: 5.52 pounds (2.5 kg).
Barrel: 18.5 inches (470.5mm) Metal smooth bore.
Power Source: 1x12 gram CO2.
Action: Semi Auto DOA with Internal Magazine.
Ammo Type: .68 Caliber Paintball or Rubber Ball.
Ammo Capacity: 16 Rounds.
FPS: 220 claimed

View fullsize

Trigger Pull: The trigger pull on Umarex T4E HDB .68 Caliber Paintball Shotgun is basically a Double Action Only Trigger as there is no blowback or way in which to preload a hammer or striker system. So basically your finger does all the work so the trigger pull is I would say about medium length and about medium pull. It does works just fine for fairly rapid follow up shooting. Each pull of the trigger also extends a rear breach-like tube that seals off the CO2 from the internal magazine or there would be a lot of CO2 leakage.

View fullsize

Accuracy: Normally I do not get the chance to perform the Field Test before making my Table Tope Video Review but with the Umarex T4E HDB .68 Caliber Paintball Shotgun, I did it the other way around so I do have performance metrics I can share with you, at least summarized. I suggest watching my Full Field Test Shooting Video Review for the Umarex T4E HDB .68 Caliber Paintball Shotgun for a the full breakdown. In summary, the Umarex T4E HDB .68 Caliber Paintball Shotgun shot a bit low on the target but had a decent grouping of I would say around 4-6 inches which is really good for a Paintball Gun. In terms of power my Chronograph results shooting 5 rounds produced an average of 176fps but the temperature was not super warm so in warmer conditions you can expect this to go up a bit, I would say 200fps is realistic.

View fullsize

Build Quality: The build quality of the Umarex T4E HDB .68 Caliber Paintball Shotgun is really good for the lower price of this unit compared to other higher priced T4E products, you will get a pretty much all plastic outer shell. That said there is still a fair amount of metal in this PaintBall Shotgun including the barrel, internal magazine, sights, trigger, sling mounts and some internal parts. All in all the Umarex T4E HDB .68 Caliber Paintball Shotgun has a good weight and feel to it with nice fit and finish.

View fullsize

Realism: The Umarex T4E HDB .68 Caliber Paintball Shotgun as far as I know is not an exact replica of any specific Shotgun but it does look like what you would expect to see from a Pistol Grip Tactical Styled Shotgun. In terms of mechanical working parts everything does what it supposed to do and works as expected.

Purchase it from the Canada Replica Airguns Store or the US Replica Airguns Store

View fullsize

Pros:

• Accuracy was really good, probably my tightest grouping so far to date with a Paintball Gun shooting at 30 feet away.

• Lots of mounting option for accessories like a tac light, laser or other sighting option with it’s top and side picatinny rail and M-LOK setup.

• Quick CO2 pierce system so you can leave a CO2 in it ready to go any time with no worries about CO2 leaking out over time.

• Simple to use Cross Bolt Safety.

• Nice high capacity super easy to load 16 round magazine.

• Ambidextrous sling mountain points.

• Low cost for what you get compared to other Umarex/T4E products.

• Build quality feels pretty good considering it is a much lower cost than other T4E rifles/shotguns.

• Looks very intimidating.

View fullsize

Cons:

• Mostly plastic external build.

• Sights are not adjustable.

• Will not get lots of shots per single CO2.

• No rear stock so will not be as accurate using a non rested shooting posting.

Comments:

The Umarex T4E HDB .68 Caliber Paintball Shotgun is a well built and decent performing Paintball Shotgun and for the price you do get a lot of gun for your money. In some ways it even outperforms the HDX in my books including lower price, ease to load, quicker follow shots being semi auto, more compact size and even accuracy was better with the Umarex T4E HDB .68 Caliber Paintball Shotgun. So if you’re on a budget, don’t feel like you are compromising at all here, you are getting a really good Paintball Shotgun solution!

• Buy the Umarex T4E HDB .68 Caliber Paintball Shotgun in Canada

• Buy the Umarex T4E HDB .68 Caliber Paintball Shotgun in the US

View fullsize

In this Field Test Shooting Video I test out the Umarex T4E HDB .68 Caliber Paintball Shotgun to see what the actual fps is and what kind of accuracy we can get out of these .68 Caliber Rubber balls at 30 feet down range. I have not done a Table Top Video just yet for the Umarex T4E HDB .68 Caliber Paintball Shotgun so stay posted for that upcoming video so stay posted for that, in the meantime you can watch my Preview Videos where I do show it up and close and go over some main specifications.

Starting with the velocity portion of this video I used .68 caliber rubber balls which are not super heavy and not made out of a very hard rubber as you can squish them with your fingers fairly easily. I put 5 rounds through my chronograph after loading a pair of 12 gram CO2 cartriges into the CO2 chamber. My results averaged 176fps which may seem slower than expected but they did hit my target pretty hard pulling the paper in with them. Each round was fairly consistent ranging from 167 to 182 fps trailing off a bit after each shot which is expected.

View fullsize

Moving on to the accuracy portion for the Umarex T4E HDB .68 Caliber Paintball Shotgun, I proceeded to shoot around 10 rounds into my fresh paper target setup 30 feet down range. My target is basically an 8.5 x 11 sheet of paper and my goal was ot get all my shots onto the paper which I easily managed. I was impressed with the grouping from the Umarex T4E HDB .68 Caliber Paintball Shotgun as it performed better than most Paintball guns using rubber balls. The shot placement was a bit lower than I was aiming but all the rounds where within I would say 4-5 inches of each other with no real outliers in the grouping.

All in all the Umarex T4E HDB .68 Caliber Paintball Shotgun performed better than I was expecting, I bit more fps would be nice but the rubber balls do hit the paper with a fair amount of energy, I would for sure not want to get hit by one at close range with light clothing on. The accuracy again was really good for a a paintball rifle and this being one of the lower cost Umarex T4E rifle/shotgun based products it performed as good if not better than much higher priced versions. If you’re looking for a fun Paintball Rifle that won’t break the bank and has a good feature set then pick one up for us!

• Buy the Umarex T4E HDB .68 Caliber Paintball Shotgun in Canada

• Buy the Umarex T4E HDB .68 Caliber Paintball Shotgun in the US

In this Preview Review Video I take a look at 4 newer products now in our Replica Airguns Online Store. One is a 4.5mm Steel BB Revolver, two are 6mm Airsoft Pistols and one is a .68 caliber Paintball Shotgun.

View fullsize

The first item I take look at in this video is the Umarex HK30 AEG Airsoft Pistol, this product is pretty entry level with analyst all plastic build and is very light to hold. It does however shoot in both semi and full auto since it is an AEG Airsfto Pistol (not many of them out there). The fps is rather low at a claimed fps at just under 200, the Umarex HK30 AEG Airsoft Pistol also comes with two 16 round remove; plastic magazines. Who knows, maybe it will be fun?

View fullsize

Next I take a look at the ASG Dan Wesson 2.5 inch 4.5mm Steel BB Gold Revolver. This is a CO2 powered shell loading BB revolver very much like similar ones I have reviewed in the past but in Gold finish. Will the gold finishes make it perform better, well I guess we better find out!

View fullsize

I then take a look at a “Glock Like” CO2 Blowback Airsoft Pistol for KJWorks called the KP13. It has a full size drop out metal magazine that holds the CO2 along with 24 rounds of 6mm Airsoft BB’s. The KJWorks KP-13 has a metal slide, metal magazine and polymer frame with a velocity over 360fps using the included barrel extension.

View fullsize

Last but perhaps the most interesting for me is the Umarex T4E HDB which is a lower cost Paintball/Rubber Ball Shotgun which could possibly be used for home protection? The T4E HDB is a mostly plastic constructed rifle with decent weight to it and uses an internal spring fed 16 round magazine. You will find all kinds of mounting points for accessories and for a sling on the Umarex T4E HDB and again at much lower cost than similar T4E rifle based Paintball/Rubber ball Airguns.

View fullsize

In this Field Test Shooting Video I test out the Umarex T4E HDX .68 Paintball Shotgun to find out what the actual fps is and if .68 Caliber Rubber Balls shot out of this Paintball gun are even going to be somewhat accurate at 30 feet out? If you have not already watched my Table Top Video where I go over the details and specifications with some closer up video showing you around the Umarex T4E HDX .68 Paintball Shotgun then make sure to watch it here…

Starting with the velocity portion of this video I used .68 caliber rubber balls which are not super heavy and not made out of a very hard rubber as you can squish them with your fingers fairly easily. I put 5 rounds through my chronograph after loading a pair of 12 gram CO2 cartriges into the CO2 chamber. My results averaged 206 fps which may seem slower than expected but they did hit my target pretty hard and actually knocked the cardboard backing right off of it. Each round was fairly consistent ranging from 203 to 210 fps.

View fullsize

Moving on to the accuracy portion of this test I proceeded to shoot around 10 rounds into my fresh paper target setup 30 feet down range. My target is basically an 8.5 x 11 sheet of paper and my goal was ot get all my shots onto the paper which I managed successfully. I would say most of the rounds all hit within about 5-6 inches of each other which for a Paintball Gun is very good! Keep in mind I was shooting using a seated position with the Umarex T4E HDX .68 Paintball Shotgun rested up front on a sand bag.

All in all the Umarex T4E HDX .68 Paintball Shotgun performed really well shooting consistent velocities and also getting all the rounds on an 8.5 x 11 inch target easily at 30 feet away which means if you where shooting at a persons body area you would easily hit it every shot making this a decent close quarters shooter which is what it really would be used for at the end of the day. Could you use it for less lethal home defense? I guess so especially if you can get your hands on pepper balls but I am not sure if regular rubber or paintballs balls would stop someone? Just seeing this impressive shotgun may in fact be more of a deterrent then being shot by it, but if it get’s the job done then why not.

• Buy the Umarex T4E HDX .68 Paintball Shotgun in Canada

• Buy the Umarex T4E HDX .68 Paintball Shotgun in the US

View fullsize

Type: Paintball Shotgun.
Manufacturer: Umarex - T4E.
Model: HDX .68 Paintball Shotgun.
Materials: Metal & Polymer.
Weight: 6.8 pounds (3.100 kg).
Barrel: 16.2 inches (411.5mm) Metal smooth bore.
Power Source: 2x12 gram CO2.
Action: Pump Action with Internal Magazine.
Ammo Type: .68 Caliber Paintball or Rubber Ball.
Ammo Capacity: 16 Rounds.
FPS: 250-360?

View fullsize

Trigger Pull: The trigger pull on Umarex T4E HDX .68 Paintball Shotgun is a single action only trigger that requires the Pump Action to engage the trigger. Without working the pump the trigger is in the rear portion and does not operate until the Shotgun is pumped, then it pops forward and becomes active. At that point I would say it is fairy short and light, maybe with a little bit of friction but not bad overall. There is also a cross-bolt safety right behind the trigger making it easy to engage and disengage the safety.

Accuracy: So far I have not had the opportunity to test the Umarex T4E HDX .68 Paintball Shotgun but plan a full Field Test Shooting Video shortly. As with most Paintball Airguns they are not going to be super accurate even at 30 feet away. Generally speaking most tests I have done with Paintball guns using rubber balls perform about the same with most of the rubber balls hitting my paper sheet target (8x11) but some even missing completely. In terms of power, on the box Umarex claims 250 fps but I have seen higher velocity specifications on websites including our own so I guess we will find out for sure when I perform my Field Test Shooting Video for the Umarex T4E HDX .68 Paintball Shotgun,

View fullsize

Build Quality: The build quality of the Umarex T4E HDX .68 Paintball Shotgun is very good since this Paintball Shotgun is made for military and law enforcement training use. It has a very good weight and feel to it and has metal parts where you would expect them including the receiver. If you picked this item up along with a real steel Shotgun it would be hard to tell or feel the difference at first inspection.

Realism: The Umarex T4E HDX .68 Paintball Shotgun as far as I know is not an exact replica of any specific Shotgun but it does look like what you would expect to see from a Tactical Styled Pump Action Shotgun. In terms of mechanical working parts everything does what it supposed to do and works as expected.

Purchase it from the Canada Replica Airguns Store or the US Replica Airguns Store

View fullsize

Pros:

• Expected fairly high fps power of 350+ with .68 caliber paintballs/rubber balls, a bit too high for your average paintball field but perhaps powerful enough to discourage an extruder?

• Lots of mounting option for accessories like a tac light, laser or other sighting option with its upper and lower picatinny rail setup.

• Quick CO2 pierce system so you can leave a CO2 in it ready to go any time with no worries about CO2 leaking out.

• Simple to use Cross Bolt Safety.

• Nice high capacity 16 round internal magazine.

• Dual CO2 offers more shots per CO2 change.

• Build quality feels really good, very solid, with lots of weight to it.

• Very intimidating looking, just that alone may scare off an intruder.

View fullsize

Cons:

• Need a tool to load rounds.

• Will not get lots of shots per dual CO2, around 70 or so but not bad.

• A bit on the large and bulky side.

View fullsize

Comments:

I am not sure exactly what one would use this Paintball Rifle for but there are a few options. You could use it on the field but with everyone else using high capacity rapid fire Paintball Guns you might be “Out Gunned” to say the least unless of course everyone else was limited in some way to their ammo capacity and rate of fire. Again the Umarex T4E HDX .68 Paintball Shotgun could be used as a non lethal home defense option when combined with the right ammunition type like say some pepper balls? The look of this Shotgun is probably enough to make an intruder get the heck out but I would not count on it. No matter what you plan to use it for it is an awesome Paintball Airgun for sure but just be aware if is not going to be the cheapest option at around $450 Canadian.

• Buy the Umarex T4E HDX .68 Paintball Shotgun in Canada

• Buy the Umarex T4E HDX .68 Paintball Shotgun in the US

As the title suggest this a video about a Huge Mystery Box so I am not going to say what’s in it, I can say that their are 4 main products mostly rifles per-say. One is a Futuristic Full Auto BB Rifle, one is a Paintball Shotgun, One is an AEG Airsoft Rifle and one is a Replica Break Barrel Pellet Rifle.

So I have a lot of variety here to show everyone! I did absolutely zero research on any of the products I show in this video since like you I had no real idea what was inside other than how many and that most where rifle based.

Enjoy finding out what new products I will be reviewing over the next month with dedicated Table Top and Field Test Shooting videos.

There are many types of magazines used in Airguns and some of this is dependent on the ammunition used.

For instance a stacked type of magazine often used for Steel BB and Airsoft can not be used for Pellets as pellets tend to deform when stacked in such a way since there is no metal casting protecting them from mashing into each other.

So what type of magazines do we generally see in Airguns? The most common Airgun magazines are as follows:

Simple Stick Magazine

• Mostly used with Steel BB but also found in some Airsoft Airguns.

• Some Pellet Airguns use a type of stick magazine with a rotary magazine on each end.

• Used in non-blowback and blowback Airguns.

• Can be made from plastic or steel or a combination of both materials.

Full Size Drop Out Magazine

• Used with Steel BB and Airsoft guns.

• Generally you will find these types magazines hold both the BB’s and CO2.

• Used in non-blowback and blowback Airguns.

• Commonly used with Airsoft Rifles in mid to high capacity.

• Can be made from plastic or steel or a combination of both materials.

Rotary magazine

• Used with Steel BB, Airsoft and Pellet Airguns.

• Used in non-blowback and blowback Airguns.

• Can be made from plastic or steel.

• Can often use mixed ammo types as in both 4.5mm Steel BB and .177 caliber pellet.

Belt Fed Magazine

• Like rotary magazine belt fed magazine can accommodate Steel BB, Pellet and Airsoft but are most often used with Pellet Airguns.

• Usually found in a full size magazine that also holds the CO2.

• Used in non-blowback and blowback Airguns.

• Can be made from plastic or steel or a combination of both materials.

Internal Magazine

• Used with Steel BB, Airsoft.

• Can have a hopper built in hat feeds a spring fed magazine.

• Usually found in lesser expensive Airguns but not a rule.

In this Video I go through each type of Airgun Magazine and talk about their differences and uses.

View fullsize

I don’t do a lot of paintball gun reviews, they just don’t come across my table all that often so it’s a lot fo fun when I do get the chance to shoot some beefier caliber ammunition in the Replica Airguns Sea Can Indoor Airgun Shooting Range. Of course I use rubber ball ammo rather than standard paintball rounds in order to keep the mess to a minimum.

I have not done my Table Top YouTube Video Review yet for the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun but you can checkout a Preview Video for now. In Summary the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun is a pretty much exactly what the name says. It’s basically a sawn off pistol grip styled double barrel shotgun that uses CO2 and shoots .68 caliber paintballs. You have a selector for shooting either out of the left or right barrel or if you want to can even both at the same time but this really slows down the fps so I would not advise it with the 200 fps version that I was testing with.

View fullsize

Now on to the actual testing of the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun! As alway I like to find out how close to the factory claimed fps I will get. Umarex claims around 200 fps for this version which is around 7.5 Joules of energy, apparently there is a 16 Joules version that shoots closer to 300 fps but we do not carry it at least right now. I put a couple fo rounds through my Umarex T4E HDS Double Barrel CO2 Paintball Shotgun using rubber ball paintballs which will be a little bit heavier than a standard paintballs and my first shot yielded 180 fps, my second shot was slightly higher at 184 fps so pretty close to the claimed 200 fps and that was in not the warmest of environments since the temperature in the Replica Airguns Sea Can Indoor Airgun Shooting Range was only 16 Degrees Celsius (60 Degrees Fahrenheit).

View fullsize

Next up it was time to see how the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun performed shooting at a target setup 30 feet away. Since there are no actual sights on the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun I had to kind eyeball it and as I shot it more and more I was able to get my shots closer to the center of the target. The Umarex T4E HDS Double Barrel CO2 Paintball Shotgun is not a tac driver but at 30 feet out you should be able to hit an 8-10 inch target pretty consistently. I don’t recommend using the double shot option since the same amount of CO2 is applied to both rounds that would normally be applied to one round decreasing the fps by about half making the paintball rounds shoot a lot slower and not really being that effective. This may be an option with the higher 300 fps version of the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun.

So all in all I had a lot of fun shooting the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun, it’s kind of like a big boy Nerf Gun that you can take onto the paintball field if you wanted to. For home defense I think it is a bit underpowered but there may be a little bit of shock factor that could slow someone down or deter them enough to either give you time get away or take shelter somewhere safe. Maybe using the pepper rounds would work OK in this situation? Either way the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun is a really cool and unique CO2 Airgun that is not overly expensive and a welcome addition to any Airgun enthusiasts collection.

• Buy the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun in Canada

• Buy the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun in the US

View fullsize

In this Unboxing Preview video you really can’t get too much different in terms of product types. First up I showcase the Umarex T4E HDS Double Barrel .68 caliber CO2 Paintball Shotgun. I then take a look at the Diana Bandit PCP and Diana Chaser CO2 Bolt Action Match Grade .177 Caliber Pellet Pistols.

The Umarex T4E HDS Double Barrel .68 caliber CO2 Paintball Shotgun is a two shot short barrelled that could come in handy for CQB engagements but it looks to be designed also as a none lethal home defence weapon since you can load a CO2 without piercing it but when in a bind you simply hit the CO2 screw and it pierces the CO2 activating the gun for instant use. I will have to test this one out to see if it really has enough power to stop an intrude, after all you only get two shots so they better count!

View fullsize

And then we have two Diana Match Grade CO2 Bolt Action Pellet Pistols, both has a similar bolt, sights, barrel and trigger setup but with the Diana Bandit you get a wooden grips, an included 10 shot rotary magazine and it’s PCP powered so you will need a compressor or a pump to use it. The Diana Chaser on the other hand is CO2 powered, has a plastic pistol grip and does not include the 10 shot rotary magazine but you can buy it later on if you get bored loading one round at a time into the breach. I expect both of these pistols to be tack drivers!

View fullsize

The Umarex T4E HDS Double Barrel .68 caliber CO2 Paintball Shotgun is available in both our Canada and US Online Replica Airgun Store while Both Diana Pellet Pistols can only be found in our Canada Store.

• Buy the Umarex T4E HDS Double Barrel .68 caliber CO2 Paintball Shotgun in Canada

• Buy the Umarex T4E HDS Double Barrel .68 caliber CO2 Paintball Shotgun in the US

• Buy the Diana Chaser CO2 .177 Caliber Pellet Pistol in Canada

• Buy the Diana Bandit PCP .177 Caliber Pellet Pistol in Canada

I made a similar video about how to hold your airgun a while back but sometimes they get a bit buried in all the video I make. I feel it's really important how you grip your gun even if it's only an airgun with very little kick or recoil. Proper pistol grip is something you should use no matter what so that you can carry it forward to what ever gun you are shooting.

More kick or recoil means a firmer grip is required to hold the gun so when shooting a powder burner with lots of kick grip becomes even more important.

In this video I go over the proper two handed grip to use when holding a pistol, which hand to hold lose and which had to grip tight, how to overlap your fingers and thumbs.

One of the most common types of question I get on my Replica Airguns YouTube channel has to be something like… Why is my Airgun not working? Most of the time the amount of info about the problem is limited to something like… “It was working yesterday but now it’s not working anymore” or something like “when I pull the trigger nothing happens”. My personal favorite is… “I took my gun apart and now it doesn’t work!”

I just made a similar video for Blank Guns and as I said in that video, trying to trouble shoot a mechanical or technical problem over the internet is very difficult, this goes for cars, guns, computers or what have you…

In this Why is My CO2 Airgun Not Working video I will however cover some of the more common and obvious problems I have seen relating to why a CO2 Airgun may not be working properly. I really don’t get a lot of questions about Spring Piston or Pump Airguns so I will be focusing on CO2 Airguns in this video. There will be a lot of crossover with CO2 Airsoft guns so this video may be helpful for some of you Airsofters out there

First let’s get the super obvious stuff out of the way! 

• Did you put a new CO2 cartridge in it and is it pierced all the way?

• Did you load BB’s or Pellets into the Airguns magazine and is the magazine in the gun correctly?

• Is the safety off?

• If the gun is a blowback semi auto single action Airgun then did you pull the slide back prior to the first shot?

CO2 Related Problems:

Not all CO2 cartridges are created equal, they often have slightly different shaped nubs on them and some brands will work better than others in different Airguns. If the shape of the CO2 nub does not fit properly into the valve area then it may not pierce or it could pierce but then not allow you to tighten it all the way losing all the CO2 in the process. If the CO2 is coming form the airguns handle to CO2 Valve area then this is an indication that your problem is related to the area where the CO2 enters the airgun.

There is a seal where the CO2 cartridge buts up to the valve, this seal can be damaged or even deformed from usage or even leaving your CO2 in the gun for too long. The outside CO2 Valve seal can also take the shape of a specific CO2 nub so when you use a different brand CO2 the seal may not properly make concat with the new CO2 type you are using, again causing leaking or even the total loss of all your CO2. Watch my YouTube video on “How to Fix Leaking CO2 in an Airgun”.

CO2 Valve Related Problems:

Again, make sure that Outside CO2 Valve Seal is in good condition and any leaking is not being caused by this problem, if you have checked the Out Side Seal and everything is OK with it then perhaps there is a problem with the CO2 valve?

One indication that your CO2 Valve might be the culprit is the total loss of all your CO2 when you try to insert and tighten a new CO2 Cartridge. Usually all the CO2 will exit the barrel, not the handle or valve area. What may be happening is the valve is stuck open or the internal seal is broken or deformed. If this is the case you will have to remove the valve and have a look inside, this is a lot easier on CO2 airguns that have the CO2 valve in the magazine, if the CO2 valve is in the actual Airguns then a lot more disassembly may be required and I would recommend an Airgun technician take care of this for you.

If the gavel is in the magazine then you will have to unscrew it, you may require a special tool for this? Once the valve is out of the magazine  take a look inside and examine the internal seal, also look for any bits of metal shavings as they can disrupt the action of the valve causing leaking. Give the inside of the valve a good clean and then lubricate it with some silence spray. hopefully that fixes your problem!

BB’s getting Stuck in the Blowback Gas Tube:

I have actually made a dedicated video for this problem so I will put a link to it in the description of this video. The main reason people may have this problem is because we all like to rack that slide on our full blowback Airguns, but if you have a fully loaded magazine then each time you reach that slide without shooting the gun, you are inadvertently trying to load another BB into the breach area, the breach is only designed to hold one BB at a time so after a few racks of the slide the newly loaded have no place to go but into the Gas Tube where they can get stuck and cause having to the operation of your Full Blowback CO2 Airgun.

BB’s Rolling Out of the Barrel of Your CO2 Airgun:

This is not actually a fault of the gun but happens because of the way the gun is designed. This situation can happen with certain CO2 Airguns when the gun user pulls the trigger really slowly while the gun is point slightly in a downward position. What is actually happening is the first part of the trigger is made to draw a BB from the magazine into the breach of the gun. If the barrel of the gun does not have a rubber hop-up stopper in it then the BB is free to roll down the barrel and out of the gun. How do you fix this problem? Be more committed to your trigger pull and or shoot at a target that is not so low. Perhaps place your targets slightly higher than the gun so the barrel is not pointing down, especially if you like to take your time with the trigger :)

A Little Maintenance Can Go a Long Way!

Sometimes a good cleans is all you need to do to get things working as they should, again I have already made video Tutorial Showing “How to Clean Airguns and Blank Guns”.

What about stuff like My Airgun is jammed or my trigger is stuck or some random part fell out of my gun?

There is only so much I can cover in this video, most other problems are going to get a bit more complicated to fix and I suggest if your Airgun is not working and the suggestions I have made in this video do not solve your problem, then consider taking your gun into a gun tech.

First off I want to say it’s hard to trouble shoot technical or mechanical problems over the internet regardless of if ithas to do with guns, cars, computers or pretty much anything where unless you are there in person it’s really hard to figure out the problem.

But I will attempt to address some of the more common issues why a blank gun may not be functioning properly.

Why is my Semi Auto Blank Gun Not Cycling or Ejecting Shells?

One very common reason a blank gun may not be cycling the shells properly is because the owner has removed the barrel restrictor plug. People usually do this to make the barrel opening look more realistic but the barrel restrictor is a necessary component to increase the back pressure allowing the slide to cycle fully to the rear position so it can eject and pickup a new shell.

The blanks you are using may not have enough gun powder in them. Some blank guns require banks with more gun powder than others, again this additional internal pressure forces the slide all the way back, if the blank does not have enough gun powder in it then only a partial slide motion happens and so the discharged shell may not eject properly, in this case the user would have to clear the blank gun manually so another shell can then be picked up and loaded into the breach.

If your blank guns is dirty or not lubricated then it may act sluggish again restricting the full movement of the slide which will effect correct operation. Make sure to thoroughly clean and lubricate your blank gun, that may be a quick fix for you!

You may have a faulty extractor? The extractor is like a hook that grabs the discharged shell while the slide is in the reward position pulling or extracting the shell out of the breach. If the extractor is worn or broken then the empty shell will not be ejected from the breach so when a new shell is picked up from the magazine it has nowhere to go and usually you will get a jam-up in the ejection port area.

One final situation that can cause your blank gun to not cycle properly is to strong of a slide spring, some blank guns out of the box just come with a really heavy slide spring, so much so that even blanks with lots of gunpowder in them are still not strong enough to make the slide operate full motion. Your only option here would be to replace the heavy slide spring with a lighter one.

Why Are My Blanks Not Firing?

This is a situation where you pull the trigger and nothing happens. Lets get the obvious causes right out of the way here… Did you put blanks in your gun and are they new blanks? Did you chamber the first round in your semi auto pistol?

So now that that’s out of the way let’s look at some other reasons why your blank gun may not be firing a blank. Perhaps the firing pin is broken? Most blank guns are not made out of carbon steel and even the firing pins can be lesser quality than what you would find in a real gun so blank guns are more prone to breaking than real guns. I have seen broken firing pins in blank guns first hand so make sure to check the firing pin and that it is fully operational.

Try changing up your blanks to another brand? Again blank gun ammunition is not made to the same higher standards that real firearm ammo is made and some primers may require a little more pressure than your gun is providing. Even with real guns an ammo change may help the gun operate better.

Why is the Trigger or Hammer Not Operating Properly?

I have come across blank guns where there are mechanical problems in the trigger and hammer areas, you may be able to address this yourself but I would recommend taking your blank gun to a gunsmith since you will have to take the gun pretty much full apart to fix a problem in the trigger and hammer areas.

Of course make sure your gun is clean and lubricated, this can help a lot with the mechanical areas of your blank gun.

One problem I saw with a few EKOL Special 99’s was specifically with the single action potion of the trigger, when I would pull the hammer back it would not lock back and the hammer would often slip and fire randomly, this is rather dangerous. When I took the gun apart I found that the table top or step that the trigger was supposed to catch on was worn down on the edge so it would simply slip off. I was able to fix this by filing a new edge on the step area. Again this can happen because blank guns are not made out of as high quality metal materials as real guns.

Why does the Flame Come out the Top of My Blank Gun and Not the Front?

If you find that the flame or discharge comes out of the top of your blank gun and not the barrel, this usually does not mean anything is wrong with your blank gun. All it means is you own a top venting blank gun and not a front firing blank gun. In some countries front firing blank guns are not allowed but front venting blank guns are. The same may also be reversed in some countries, for instance here in Canada we can only import front firing blank guns with flare adaptors since our blank guns are imported under the assumption that they are to be used as signaling or flare devices.

Can I Convert my Top Venting Blank Gun into a Front Venting Blank Gun?

I really don't recommend altering a blank gun in any way as it may be a violation of your local laws and it could cause the blank gun to malfunction in a very bad way causing serious injury or even death!

In theory I suppose it may be possible to convert your Top Venting Blank Gun into a Front Venting Blank Gun but again you would need to allow for just the right amount of back pressure so a wide open barrel would not work unless it was a revolver. You can not simply remove the red plug and bingo you have a front firing blank gun because in most cases the barrel will be completely plugged in the frontal region. Not only would you need to drill out the plugged portion of the barrel but you would also have to somehow fill in the top venting area and again makes sure to allow for just enough back pressure to cycle the slide back and forth.

Hopefully this has helped some of you with blank gun issues. If you’re looking for a blank gun make sure to come down to www.ReplicaAirguns.ca and www.ReplicaAirguns.us and have a look in our blank gun area of our online stores.

I already made several review videos for both Gletcher NGT (4.5mm Steel BB) and the Gletcher NGT R (.177 Cal Pellet) Revolvers, including table top and shooting videos. So make sure to check those videos out for more information on both versions of Gletcher NGT and NGT R Revolvers.

I did however miss some noteworthy details that I wanted to cover in this video. Firstly, the real steal Nagant M1895 Revolver this Gletcher NGT is styled after has a very unique gas-sealing system that the Airgun version does not replicate or really require but it is worth mentioning.

Here is some more info on how the original Nagant M1895 Revolver Gas Seal System works:

(From Wikipedia) The M1895 by contrast, has a mechanism which, as the hammer is cocked, first turns the cylinder and then moves it forward, closing the gap between the cylinder and the barrel. The cartridge, also unique, plays an important part in sealing the gun to the escape of propellant gases. The bullet is deeply seated, entirely within the cartridge case, and the case is slightly reduced in diameter at its mouth. The barrel features a short conical section at its rear; this accepts the mouth of the cartridge, completing the gas seal. By sealing the gap, the velocity of the bullet is increased by 15 to 45 m/s (50 to 150 ft/s.) This feature also eliminates the possibility of injury through the dangerous expansion of gases from the cylinder behind the barrel, which are easily capable of severing a finger if the user holds the gun incorrectly (with a finger positioned in front of the cylinder during fire) - a noted safety-issue in conventional revolvers.

Moving on to some of the features incorporated into the Gletcher NGT NGT-R CO2 BB and Pellet Revolver that I did not point in any of my previous videos. There is an extractor rod that can be used to extract a shell, this is not really necessary on the airgun version since the shells do not expand and tighten on the cylinder as they would n the real steal Nagant M1895 Revolver built is nice that we can replicate this feature with the Airgun version. You can also remove the cylinder completely from both the BB and Pellet shooting Gletcher NGT NGT-R CO2 Revolvers. The cylinder is actually very heavy and adds a lot of weight to this compact 7 shot Revolver.

It is always nice when an Airgun is built in such a way that it replicates the real steal version as closely as possible and the Gletcher NGT NGT-R CO2 BB and Pellet Revolvers do this nearly perfectly.

Buy Gletcher NGT Revolvers in Canada

Buy Gletcher NGT Revolvers in the US