View fullsize

Airguns are not toys and as so require proper storage, transportation and handling so as not to cause an accident that could be minor or even deadly.

No matter if you are handling an Airgun or a “Real Gun”, they should both be handled in the same manner even if the consequences from an accident with an Airgun may be less serious. Life long injuries like the loss of an eye are nothing to be taken lightly.

For the most part, what I talk about in this Airgun Safety 101 video can also be applied to a “Real Gun” although most countries will have stricter laws and guidelines in the storage, transportation and handling of “Real Guns” over an Airgun.

View fullsize

Storing Your Airgun:

In Canada an unregulated Airgun does not have any real specific safe storage guidelines but common sense should be used and I recommend that you at the bare minimum keep your Airgun in some sort of locked space whether it be a safe, cabinet or room that is locked all of the time.

You can also put a trigger lock on your Airgun if you do not have a lockable storage location for it.

You should also make sure to store your Airgun unloaded, at least when it comes to BB’s and or Pellets. If there is some unused CO2 in it, or it is charged with Compressed Air, but unloaded in terms of ammunition, that is OK, but again keep it in a safe location away from anyone that may be able to get their hands on it and hurt themselves or others.

View fullsize

Transporting Your Airgun:

Again, in Canada an unregulated Airgun does not have any real transportation guidelines but if you keep your Airgun out in the open and someone sees it, they will most certainly call the police and more than likely you may find yourself staring down the wrong end of a police firearm, at least until they sort it all out. This is very serious as unfortunately people have died as a result of handling their Airguns out in the open and underestimating what kind of police response that may entail.

For that reason alone, always keep your Airgun out of sight in a case or backpack or the trunk of your car. Never transport your Airgun loaded and it is best if you can lock it in a case or put a trigger lock on it for added safety when transporting it.

View fullsize

Shooting Your Airgun:

Shooting your Airgun is always the most enjoyable part of owning an Airgun, so don’t do something stupid and turn that experience into a nightmare. Treat your Airgun as if it is deadly at all times, never point it at anything you do not intend on shooting.

Keep your safety on until you are ready to shoot. Never put your finger on the trigger until you are ready to shoot it and only shoot it in a safe location with an appropriate background and backstop.

Think of the barrel of your Airgun as a light saber that if it crosses even your arm, it could cut it off. Even a BB to the arm is a serious matter. I had a friend that shot himself in the arm with a BB Gun and the BB lodged in the tendons of his wrist requiring an operation to remove it. He was a violin player so this could have ended his violin playing, but luckily he was OK.

When Your finger is not on the trigger it should be held across the trigger guard in a straight position to ensure no accidental misfires.

Wear eye protection, Steel BB’s will bounce back when they hit a hard surface and can come back with enough force to injure an eye easily. Generally Airguns do not require ear protection but some can be loud enough that you may want to wear some sort of ear protection as a precaution.

Only shoot with others that are responsible and take Gun Safety very seriously. Young people will need constant supervision and it is best to go through all of this first before even considering handing them an Airgun for the first time. Perhaps start them off with something like an Airsoft gun which will have less consequences if an accident were to take place.

Airguns are awesome in so many ways and allow for a similar shooting experience to a “Real Gun”. They can be used in more situations, with less overall cost and are a great way to learn proper gun handling and how to improve your shooting ability even if you are a “Real Gun” owner. Always be responsible with your Airgun not only for yourself but for others as it only takes a few idiots to ruin things for the rest of us. Don’t be that Idiot please!

• Buy Airguns in Canada

• Buy Airguns in the US

View fullsize

What you can expect from this Field test Shooting Video for the Barra 1866 Junior Dual Ammo Pump Cowboy Rifle are two things for sure. I test out the velocity with both 4.5mm Steel BB’s and .177 caliber lead pellets, I also chuck both of these rounds downrange to see if one may be more accurate than the other and how close I can get a 5 shot grouping for each ammunition type. If you are looking for details and specifications and perhaps some more close up video of the Barra 1866 Junior Dual Ammo Pump Cowboy Rifle then you may want to watch my Table Top Video for it here.

If you have watched any of my hundreds of Field Test Videos, then you already know I start off shooting 5 or so rounds through my Chronograph to see what the average velocity is going to be. In this Field Test I shoot 3 rounds of each ammo type, 3 BB’s and 3 pellets since it is a pump Airgun and they tend to be more consistent than a CO2 Airgun. Barra claims around 350 fps, I am not sure if this is for BB’s or Pellets or both? As it turns out (spoiler alert), both ammo types performed about the same in both the velocity and accuracy portion of my testing. For BB’s, my chronograph testing got 303, 316 and 316 for an average of 312 fps. For pellets my chronograph results were 309, 309, 314 for an average of 311, so only 1 fps off between the two. Keep in mind the BB’s weigh around 5.1 grain while the pellets I was using were around 7 grain, so the pellets will be carrying more energy downrange and hit a bit harder. By the way they are also harder to load so I would suggest just shooting the steel BB’s in this one since you can keep the fun times flowing better...

Next up for my accuracy test of the Barra 1866 Junior Dual Ammo Pump Cowboy Rifle, I again shot both ammo types, but 5 rounds of each and just like the velocity test they matched each other almost exactly. Both the steel BB’s and lead pellets I was using shot really well centered left to right, maybe just a hair to the left and both shot just about an inch or so high on the bullseye I was aiming at 30 feet away. The 5 BB’s grouped nicely for me at about an inch while the pellets did get a slightly tighter 3/4 inch grouping for me in this test. I was using a semi rested shooting position sitting on a stool in the back with the rifle rested on a sand bag up front.

The Barra 1866 Junior Dual Ammo Pump Cowboy Rifle really surprised me in how it performed, It’s not going to be the most powerful BB/pellet cowboy rifle out there but compared to a Red Ryder it does have a bit more punch and in terms of accuracy I found it shot better for me than at least I can do with a Red Ryder type BB rifle. You also have the option of shooting BB’s or Pellets but I would recommend shooting BB’s since you have that 50 round hopper and the BB’s auto load when you pull the bolt back which is much easier than loading pellets with a pair of tweezers which is what I needed to do to get them in with my sausage fingers. One more thing to mention is I do not recommend pumping this air rifle more than 1 time, not only does the manual say not to, but there is little benefit in pumping it more times with only the risk to damaging the airgun. I pumped it 4 times and only got about 20 fps more out of it so just don’t do it. If you want a Cowboy style Air Rifle with a little more realism than say a Red Ryder but that shoots about the same then checkout the Barra 1866 Junior Dual Ammo Pump Cowboy Rifle.

• Buy the Barra 1866 Junior Dual Ammo Pump Cowboy Rifle in Canada

• Buy the Barra 1866 Junior Dual Ammo Pump Cowboy Rifle in the US

View fullsize

Type: Lever/Pump Dual Ammo Rifle
Manufacturer: Distributed by Barra.
Model: Junior Dual Ammo Pump Cowboy Rifle.
Materials: Mostly plastic, some metal.
Weight: 4.1 pounds (1859 grams).
Total Length: 36 inches (91.44mm).
Barrel: 18 inches (45.7cm) metal rifled.
Propulsion: Pump Compressed Air.
Action: Lever/Pump
Ammunition Type: .4.5mm steel BB’s & .177 Caliber Pellets.
Ammunition Capacity: 50 BB’s in hopper, single shot Pellets.
FPS: Claimed 350-400.

View fullsize

Trigger Pull: The trigger pull on Barra 1866 Junior Dual Ammo Pump Cowboy Rifle is respectable at about 5 pounds with a medium to short pull length. I would say it is perfect for novice shooters as it is not overly light so as not to go off easily by accident and not too heavy for youth shooters with less finger strength than adults. When you pull the bolt back to reload the ammo, the internal cocking mechanism is activated allowing for single action type shooting. You do need to activate the bolt with each shot.

View fullsize

Accuracy: My dedicated field test shooting video is planned for this week, so for now I have no idea what to expect in terms of velocity and accuracy from the Barra 1866 Junior Dual Ammo Pump Cowboy Rifle, other than it is claimed to shoot around 350 fps when using pellets. It does have an 18 inch rifles barrel which should contribute to helping a lot with accuracy, so I do have high expectations especially since it has a pretty good trigger and when looking down the sights they allow for a nice tight fix on the target. The rear stock is short but not so short that it feels cramped for an adult shooter which should also help when I perform my accuracy test.

View fullsize

Build Quality: The Barra 1866 Junior Dual Ammo Pump Cowboy Rifle is nothing special when it comes to materials being used in it. It is for the most plastic with the exception of the inner and outer barrel along with the rear sight and I would imagine some other internal parts. It does feel not so bad as it is a bit over 4 pounds and is smaller in nature so it feels solid enough in the hand. I wish the Pump/Lever was metal as it would of felt a bit more solid and would have added a bit more additional weight to the Barra 1866 Junior Dual Ammo Pump Cowboy Rifle. Fit and finish is good and overall the gun looks and feels good.

View fullsize

Realism: The Barra 1866 Junior Dual Ammo Pump Cowboy Rifle is essentially styled after the Old West Lever Action Cowboy Rifle, and it has everything we would expect other than loading shells which is available in other Lever Action Air Rifles if you don’t mind paying a premium for one. The lever is actually not a lever but more of a pump so the action and look of the lever is not exactly as you would expect from a true lever action rifle, but when it is locked in place it does look the part. The gold receiver and rifle band looks sharp and I feel matches up with the dark imitation wood stock nicely. One point to make is that the hammer is not the hammer but actually the safety and the bolt not only opens the breach area but also acts as the cocking mechanism for the internal hammer.

View fullsize

Pros:

• Super easy to pump.

• Fit and finish looks decent for a mostly plastic airgun.

• In terms of realism it does look like a more compact lever action rifle for the most part

• Can shoot either BB’s or Pellets.

• Holds 50 BB’s in the hoper for quicker follow up shooting.

• Metal octagon outer barrel adds addition weight to a mostly plastic gun.

• Rear sight is metal and is also adjustable for elevation.

• Trigger pull is pretty decent, not too light but is short and about 5 pounds.

• Recessed barrel for added realism.

• Made for kids but the shoulder pull length and sight placement works for adults too.

• The gold receiver looks good and gives it a unique look.

Cons:

• Mostly plastic build.

• Manual says only one pump but I wonder why this is the case or perhaps just to deregulate it?

• Pellets are hard to load especially if you have larger hands and fingers.

View fullsize

Comments:

The Barra 1866 Junior Dual Ammo Pump Cowboy Rifle is a competitor for products like the Red Ryder but it has a bit more realism in terms of looking more like a replica of a real steel Lever Action Cowboy Rifle. It also allows for shooting pellets and has an actual rifled barrel so hopefully this helps with accuracy. You can still kind of shoot it Lever Action Style when shooting BB’s but there is the addition of charging the bolt with each shot over and above working the Lever / Pump, so it will take a bit more time to get those follow up shots as compared to a Red Ryder BB Rifle. One other point to make is that the lever is actually not a lever but more of a pump since this is not spring powered but instead has an air reservoir which on this version only allows for one pump, but on the non-junior version you can pump it up to 10 times and get a claimed 800 fps out of it (US Version). I am going to try pumpkin the Barra 1866 Junior Dual Ammo Pump Cowboy Rifle up to three times to see if there is any difference in power but this could void your warranty if you damage the air reservoir by over pressuring it. So be good and only pump yours once as instructed in the manual.

• Buy the Barra 1866 Junior Dual Ammo Pump Cowboy Rifle in Canada

• Buy the Barra 1866 Junior Dual Ammo Pump Cowboy Rifle in the US

There are many types of magazines used in Airguns and some of this is dependent on the ammunition used.

For instance a stacked type of magazine often used for Steel BB and Airsoft can not be used for Pellets as pellets tend to deform when stacked in such a way since there is no metal casting protecting them from mashing into each other.

So what type of magazines do we generally see in Airguns? The most common Airgun magazines are as follows:

Simple Stick Magazine

• Mostly used with Steel BB but also found in some Airsoft Airguns.

• Some Pellet Airguns use a type of stick magazine with a rotary magazine on each end.

• Used in non-blowback and blowback Airguns.

• Can be made from plastic or steel or a combination of both materials.

Full Size Drop Out Magazine

• Used with Steel BB and Airsoft guns.

• Generally you will find these types magazines hold both the BB’s and CO2.

• Used in non-blowback and blowback Airguns.

• Commonly used with Airsoft Rifles in mid to high capacity.

• Can be made from plastic or steel or a combination of both materials.

Rotary magazine

• Used with Steel BB, Airsoft and Pellet Airguns.

• Used in non-blowback and blowback Airguns.

• Can be made from plastic or steel.

• Can often use mixed ammo types as in both 4.5mm Steel BB and .177 caliber pellet.

Belt Fed Magazine

• Like rotary magazine belt fed magazine can accommodate Steel BB, Pellet and Airsoft but are most often used with Pellet Airguns.

• Usually found in a full size magazine that also holds the CO2.

• Used in non-blowback and blowback Airguns.

• Can be made from plastic or steel or a combination of both materials.

Internal Magazine

• Used with Steel BB, Airsoft.

• Can have a hopper built in hat feeds a spring fed magazine.

• Usually found in lesser expensive Airguns but not a rule.

In this Video I go through each type of Airgun Magazine and talk about their differences and uses.

In this SHOT Show Las Vegas 2020 Interview Video Scott takes us through a range of new products from Air Venturi.

View fullsize

Scott and I talk about the Air Venturi TR5 and how it came about to fill the hole the Baikal MP-61 left behind. We also talk a look at some new Air Rifles, a pumper called the Butterfly with a super cool linkage based system that makes pumping a lot easier. A PCP side lever cocking Air Rifle that I’m not even sure has a name yet but will be available in .177 .22 and .25 caliber pellet for around $299 US.

View fullsize

The only Air Venturi replica we looked at is a new Springfield Armory under lever Spring Piston Air rifle modeled after the M1A. Last up Scott went showed us how the Bada Bang targeting system is shaping up and looks to be almost ready for production.

View fullsize

The Umarex Strike Point is a lot like the Crosman series of bolt action multi-pump pellet shooters at least in design. Sure it has a more futuristic and plastic build to it but mechanically it works pretty much the same as the Crosman Bolt Action Multi-pump Pellet Pistols. What I really wanted to know is will the Umarex Strike Point .22 Caliber Pellet Pistol perform as good?

View fullsize

Umarex states that you can pump the Umarex Strike Point .22 Caliber Pellet Pistol 10 times maximum so that's what I will did for my Feet Per Second Testing and the Umarex Strike Point .22 Caliber Pellet Pistol was very consistent producing a 427 fps 3 shot string using fairly heavy 14.3 grain lead pellets. Of course lighter alloy pellets should go right up to the claimed 500 fps. I also tested out a 5 pump shot to see what kind of velocity I would get since you don't always need maximum power for basic plinking and target shooting. The velocity did drop as expected but not that much getting 356 fps which is plenty fast for all intents and purposes.

View fullsize

Moving on to my Target accuracy testing, I placed 6 shot in total on my paper target setup 30 feet down range using a rested and seated shooting position. My first 4 shots made a single half inch hole but then my shooting table seemed to move on my 5th and 6th shot making me use a slightly different hold and I believe this caused these 5th and 6th shots to drop a bit. Based on my first 4 shots I expect the Umarex Strike Point .22 Caliber Pellet Pistol to shoot consistent half inch groupings from 30 feet away especially once you get use to the trigger and sights. The shots where all a bit low but this is not a problem since the rear sight on the Umarex Strike Point .22 Caliber Pellet Pistol is adjustable for windage and elevation.

View fullsize

All in all the Umarex Strike Point .22 Caliber Pellet Pistol is a nice target and even small pest control air pistol for at least closer up shooting. The trigger is not as light as the Crosman series but it works just fine. If you want something a little more up to date than what Crosman is offering in a bolt action multi-pump Pellet Pistol then you may want to consider the Umarex Strike Point .22 Caliber Pellet Pistol as an option.

• Buy the Umarex Strike Point .22 Caliber Pellet Pistol in Canada

• Buy the Umarex Strike Point .22 Caliber Pellet Pistol in the US

Some more Airguns to show everyone! Today I have three very different styles for you... In this Preview video I show off a Multi-pump Pellet Target Pistol, a CO2 Blowback Airsoft Pistol and an AEG AK47 Kalashnikov with all the bells and whistles!

View fullsize

First off is the Strike Point Multi-pump .22 Caliber Target Pellet Pistol from Umarex. It's kind of like the Crosman 1322 Pistol but with more plastic parts on the outside so it's a little bit more bulky than the Crosman. Other than that both Multi-pump Target Air Pistols share similar bolt actions, cross bolt safeties and adjustable rear sights. With 10 pumps you shoudl get around 465 fps form a standard .22 caliber lead pellet so the Umarex Strike Point Multi-pump .22 Caliber Target Pellet Pistol should even be OK for small pest control as long as it proves to be accurate.

View fullsize

I previously reviewed the KWC M40 in it's standard barrel length, the KWC M&P 40 Extended Barrel Airsoft Pistol is pretty much the same Airsoft pistol but with an extended slide and barrel along with higher sights and a vented slide. I also like the stainless steel barrel which give the KWC M&P 40 Extended Barrel Airsoft Pistol a nice tow tone look.

View fullsize

Lastly I take a look at a full featured AEG Kalashnikov Tactical AK47 Airsoft Rifle that comes with everything you are going to need including the battery, charger, two 550 round magazines and an included fore-grip. The AK47 Kalashnikov Tactical 60Th Ann. Airsoft Rifle feels really good in the hands with its near 7 pounds of weight. I look forward to giving this AEG Airsoft rifle a test run for sure!

View fullsize

• Buy the Umarex Strike Point Easy Load Bolt .22 Pellet Airgun in Canada

• Buy the Umarex Strike Point Easy Load Bolt .22 Pellet Airgun in the US

• Buy the KWC M&P 40 Extended Barrel Airsoft Pistol in Canada

• Buy the AK47 Kalashnikov Tactical 60Th Ann. Airsoft Rifle in Canada

• Buy the AK47 Kalashnikov Tactical 60Th Ann. Airsoft Rifle in the US

I made a similar video about how to hold your airgun a while back but sometimes they get a bit buried in all the video I make. I feel it's really important how you grip your gun even if it's only an airgun with very little kick or recoil. Proper pistol grip is something you should use no matter what so that you can carry it forward to what ever gun you are shooting.

More kick or recoil means a firmer grip is required to hold the gun so when shooting a powder burner with lots of kick grip becomes even more important.

In this video I go over the proper two handed grip to use when holding a pistol, which hand to hold lose and which had to grip tight, how to overlap your fingers and thumbs.

View fullsize

Type: Multi-pump Pellet-BB rifle.
Manufacturer: Umarex USA.
Model: NXG APX.
Materials: Metal and polymer parts.
Weight: 3.4 pounds (1.54 kg).
Barrel: 20 inches, rifled.
Propulsion: Multi-pump.
Action: Single shot pellets/repeater BB's.
Ammunition Type: .177 caliber pellets & 4.5mm steel BB's.
Ammunition Capacity: 75 BB's in hopper.
FPS: up to 490.

View fullsize

Trigger Pull: The trigger pull on the Umarex NXG APX Multi-pump Pellet-BB Rifle is not too bad, I would not say it's overly light but not on the heavy side either. Essentially it has a single action trigger since you need to pre-charge the bolt to engage the trigger. There is a little bit of take-up and then a fairly noticeable break point where you will feel the most trigger weight right before it releases.

View fullsize

Accuracy: So far I have not performed my Field Test Shooting review for the Umarex NXG APX Multi-pump Pellet-BB Rifle so I do not have any velocity or accuracy information to share at this point. I do plan on making that Shooting video Review this week so stay posted for that one.

View fullsize

Build Quality: The Umarex NXG APX Multi-pump Pellet-BB Rifle is not going to be one of your highest quality airguns but it does get the job done and feels solid enough with all the working parts feeling tight and secure. Most of the Umarex NXG APX Multi-pump Pellet-BB Rifle is plastic, even the bolt and trigger but you will find more metal inside where it counts like the inner steel barrel and the outer steel barrel shroud. The stock is plastic and that's OK, I do like the addition of the rubber butt pad and cheek rest as they work well and help to make the Umarex Umarex NXG APX Multi-pump Pellet-BB Rifle feel comfortable to hold in position and shoot.

View fullsize

Realism: Since the Umarex NXG APX Multi-pump Pellet-BB Rifle is not a replica, realism is not really a factor here but it does look like a gun so treat it as if it was a real gun since most people will not know the difference. Always transport and store any airgun safely and discreetly.

View fullsize

Pros:

• Low cost air rifle with a lot of features.

• Iron sights actually look really usable with the fiber optic red dot up front.

• Comes with an 4x15 optical sight which should help with accuracy at longer ranges.

• Super easy to pump even when getting close to the 10 pump max.

• Built in auto safety.

• Stock and cheek rest position feel really good.

• Choice of shooting pellets or BB’s.

• Trigger feels pretty good, not too heavy.

• Mostly an ambidextrous design so good for lefties too.

• Has a rifled barrel.

• Overall a good looking air rifle.

View fullsize

Cons:

• Mostly plastic, not the highest quality build.

• Included 4x15 scope is super low budget but will work till you can upgrade it down the road.

View fullsize

Comments:
I really hope the Umarex NXG APX Multi-pump Pellet-BB Rifle shoots well as it is kind of a cool air rifle with a lot of features at a low price tag and would make a great little target and maybe even small pest air rifle if it turns out to be accurate and hit that near 500 fps mark with pellets. The Umarex NXG APX Multi-pump Pellet-BB Rifle is not going to win any quality or design awards but from a usability stand point it works well and feels good to hold and shoot, the rear stock and cheek rest are in a perfect piston for me and this is a pretty small airgun overal. Personally I would invest in an upgraded scope, something like the Walther 4x32 would be perfect and not too expensive.

The Umarex NXG APX Multi-pump Pellet-BB Rifle is available in both the Stand Alone Air Rifle and Kit Version that comes with the addition of safety glasses, targets and ammo.

Buy Umarex NXG APX Multi-pump Pellet-BB Rifle in Canada

Buy Umarex NXG APX Multi-pump Pellet-BB Rifle in the US

View fullsize

For my first official Field Test Shooting Video I test out the Crosman American Classic P1322 22 Caliber Pellet Pistol! Perhaps I should start calling these videos Sea Can or Shipping Container Shooting videos? Anyway, like always I put some rounds through the Chronograph to see what kind of real world fps I get from the Crosman American Classic P1322 22 Caliber Pellet Pistol. You will all be happy to know the Chrony is working really well in its new home. I played around with it a bit and found that using the light kit I bought gets me very consistent fps readings :)

Since the Crosman American Classic P1322 22 Caliber Pellet Pistol is a multi-pump airgun there is no real need to shoot more than 3 or so shots, after all there is a fair amount of pumping involved. After three consistent test shots the variation was only about 2 fps apart coming in at an average of 491 fps using Crosman flathead pellets that I would say are around 12-13 grain in weight. Just for fun a did a half pump only cracking the Crosman American Classic P1322 22 Caliber Pellet Pistol 5 times to see what a half power shot would result in and it did scrub off about 200 fps, still good enough for target plinking.

View fullsize

Next up I performed my accuracy test shooting from close to 30 feet back on a paper target using a rested position, (sitting in the back with my hands resting on a sand bag). Still a bit of human factor involved but stable enough to get a good idea of the accuracy for the Crosman American Classic P1322 22 Caliber Pellet Pistol. I had a bit of a camera technical problem so I ended up performing this test twice, the first time I got about a 3/4 inch 5 shot group. The second time I rushed it a bit and ended up widening out the group a little.

Overall the Crosman American Classic P1322 22 Caliber Pellet Pistol is a really great target and even small pest close range pistol that you can pickup at a very affordable price. I really wish we carried a few of the Crosman airguns, at least ones like this, perhaps down the road...

Type: Pellet Air Pistol.

Manufacturer: Crosman.

Model: P1322 American Classic.

Materials: Metal & plastic.

Weight: 2 pounds.

Barrel: 10.25 inches, metal rifled.

Propulsion: Multi-pump pneumatic, up to 10 pumps.

Action: Bolt-action single shot, single action only.

Ammunition Type: .22 caliber pellets.

Ammunition Capacity: 1 round.

FPS: 460.

Trigger Pull: The trigger pull on the Crosman American Classic P1322 22 Caliber Pellet Pistol is non-adjustable but is short and fairly light with virtually no creep at all, it's just right there! The Crosman American Classic P1322 will allow for very accurate shot placement with only a little trigger time required to get use to the release tension required.

Accuracy: I found my Original Crosman 1377 (The .177 caliber version of this airgun) to be an amazing target pistol, getting about a 1/2 inch grouping from 30 feet out in a semi-rested position. And I even performed my accuracy test twice with the same result each time. In terms of fps performance, the Crosman American Classic P1322 22 Caliber Pellet Pistol is not required to be detuned for Canada importation so we should see very close to 460 fps even using heavier grain lead pellets! Make sure to look for my upcoming Field Test Shooting video for the Crosman American Classic P1322 22 Caliber Pellet Pistol.

Build Quality: The Crosman American Classic P1322 22 Caliber Pellet Pistol is not a fancy looking airgun but it gets the job done with a mostly all metal design and build. Remember this Croman configuration has been around since 1977 so about  40 years and has pretty much stayed the same so Crosman must be doing something right with the American Classic series if it has stood the test of time with very few changes to its design other than some cosmetics ones.

Realism: The Crosman P1322 American Classic Air Pistol is not a replica of any gun out there. The P1322 is made as a target airgun, so it looks like a target air pistol and is not expected to resemble a tradition real steel pistol of any sort.

Pros:

• Fairly inexpensive target pistol (under $100 Canadian - $79 US)

• Know to be very accurate.

• Ability to regulate power with the amount of pumps.

• Mostly all metal construction.

• Rifled steel barrel.

• Adjustable rear sight.

• Light single action trigger.

• Would be good for small close shot pest control because of good FPS and good accuracy for shot placement ability.

• Lots of mods and upgrades available for this series of Crosman Airguns.

Cons:

• The trigger is a bit thin (Can be upgraded).

• Rear sight is adjustable but is hard to setup.

• All black sights are hard to aim on darker targets.

• Pumping is fairly firm and will take some time for max 10 pump power.

Comments:

The Crosman American Classic P1322 22 Caliber Pellet Pistol is a bit of a sleeper target pistol. It has been around for a long time and for this reason can be overlooked. It also is a super flashy looking airgun that requires a bit of manual pumping to get to maximum power. There is also the kind of finicky sight setup required to get this air pistol to shoot on target. If you can put all that aside you have yourself a super accurate and rather powerful little target or even small pest control airgun for a lot less money than some other pellet target pistols out there. And to be honest I would trade having to pump this gun up over a springer for the main reason that the recoil is so much less violent on a pump gun allowing for better accuracy at the end of the day. When you factor in all the mods that are available for this line of Crosman Airguns the sky is the limit allowing for a ton of customization in performance and looks.

My Vimeo Video Review of the Crosman P1322 American Classic .22 Caliber Target Pistol:

Buy Pellet Airguns in the Canada Store

First off, I want to thank Crosman for providing these two guns for review! Now they're not exactly new guns by any means but for sure worth showing and doing some update reviews for.

Starting with the Crosman PFAM98 Taurus PT-92:

The Crosman PFAM98 Taurus PT-92 is essential a KWC made M92 also branded as the same gun as the Cybergun GSG 92 and the Swiss Arms P92.

So for all intense and purposes if you have watched any of my other revise on this line of KWC Beretta /Taurus BB pistols and even Airsoft versions then this BB gun should be really familiar to you.

History of the Taurus PT-92:

It is often referred to as a Berate 92 copy but in fact it is a Taurus PT-92 replica. The Taurus PT-92 is a product of Brazil, Taurus actually bought the entire Brazilian Beretta factory back in 1980 including drawings, tooling, machinery, and a very experienced work force to make the guns. Taurusimmediately sought to improve on the Beretta design, resulting in the popular and acclaimed Taurus PT-92.

Specifications for the Crosman PFAM98 Taurus PT-92:

• Full Blowback operation.

• Full metal frame, slide and magazine.

• 12 gram CO2.

• 4.5mm steel BB’s.

• 20 shot full size drop out metal magazine.

• Smooth bore barrel.

• Single and double action trigger.

• 2.44 pounds (1107 grams).

• Up to 400fps.

• Replica of Taurus PT-92.

• Made for Crosman by KWC in Taiwan.

Next up the Crosman American Classic P1322.

The American Classic P1322 is basically a .22 caliber version of the .177 caliber 1377 Pneumatic Pump Air Pistol. So make sure to watch the video reviews I have already done for the Crosman American Classic P1377. Other than caliber the .22 caliber version at least in Canada is more powerful since it has not been detuned for Canada import. The .22 caliber version has a claimed fps of 460 which is under our 500 fps import limitation while the standard non detuned .177 caliber version has a max claimed fps of up to 600 which can set off alarms at customs. For this reason the Crosman American Classic P1377 Canada version is detuned to shoot under 500 fps.

Crosman use to make a similar version of the Crosman American Classic P1322 called the Back Packer which had a slightly longer barrel and came with a removable stock. You can kind of replicate this gun by adding the stock but it will have a shorter barrel. Keep in mind there are a ton of mods available for this series of Crosman airguns including barrels, bolts, trigger, Internals stocks, scope mounts…

PHOTOSpecifications for the Crosman American Classic P1322:

• Metal and plastic construction.

• Pneumatic pump.

• .22 caliber lead pellets.

• Single shot bolt action.

• Rifled metal barrel.

• Single action only.

• Up to 460fps using lead pellets (10 pumps).

• 1.88 pounds (853 grams)

Keep posted for my full update reviews for these airguns...

One of the most common types of question I get on my Replica Airguns YouTube channel has to be something like… Why is my Airgun not working? Most of the time the amount of info about the problem is limited to something like… “It was working yesterday but now it’s not working anymore” or something like “when I pull the trigger nothing happens”. My personal favorite is… “I took my gun apart and now it doesn’t work!”

I just made a similar video for Blank Guns and as I said in that video, trying to trouble shoot a mechanical or technical problem over the internet is very difficult, this goes for cars, guns, computers or what have you…

In this Why is My CO2 Airgun Not Working video I will however cover some of the more common and obvious problems I have seen relating to why a CO2 Airgun may not be working properly. I really don’t get a lot of questions about Spring Piston or Pump Airguns so I will be focusing on CO2 Airguns in this video. There will be a lot of crossover with CO2 Airsoft guns so this video may be helpful for some of you Airsofters out there

First let’s get the super obvious stuff out of the way! 

• Did you put a new CO2 cartridge in it and is it pierced all the way?

• Did you load BB’s or Pellets into the Airguns magazine and is the magazine in the gun correctly?

• Is the safety off?

• If the gun is a blowback semi auto single action Airgun then did you pull the slide back prior to the first shot?

CO2 Related Problems:

Not all CO2 cartridges are created equal, they often have slightly different shaped nubs on them and some brands will work better than others in different Airguns. If the shape of the CO2 nub does not fit properly into the valve area then it may not pierce or it could pierce but then not allow you to tighten it all the way losing all the CO2 in the process. If the CO2 is coming form the airguns handle to CO2 Valve area then this is an indication that your problem is related to the area where the CO2 enters the airgun.

There is a seal where the CO2 cartridge buts up to the valve, this seal can be damaged or even deformed from usage or even leaving your CO2 in the gun for too long. The outside CO2 Valve seal can also take the shape of a specific CO2 nub so when you use a different brand CO2 the seal may not properly make concat with the new CO2 type you are using, again causing leaking or even the total loss of all your CO2. Watch my YouTube video on “How to Fix Leaking CO2 in an Airgun”.

CO2 Valve Related Problems:

Again, make sure that Outside CO2 Valve Seal is in good condition and any leaking is not being caused by this problem, if you have checked the Out Side Seal and everything is OK with it then perhaps there is a problem with the CO2 valve?

One indication that your CO2 Valve might be the culprit is the total loss of all your CO2 when you try to insert and tighten a new CO2 Cartridge. Usually all the CO2 will exit the barrel, not the handle or valve area. What may be happening is the valve is stuck open or the internal seal is broken or deformed. If this is the case you will have to remove the valve and have a look inside, this is a lot easier on CO2 airguns that have the CO2 valve in the magazine, if the CO2 valve is in the actual Airguns then a lot more disassembly may be required and I would recommend an Airgun technician take care of this for you.

If the gavel is in the magazine then you will have to unscrew it, you may require a special tool for this? Once the valve is out of the magazine  take a look inside and examine the internal seal, also look for any bits of metal shavings as they can disrupt the action of the valve causing leaking. Give the inside of the valve a good clean and then lubricate it with some silence spray. hopefully that fixes your problem!

BB’s getting Stuck in the Blowback Gas Tube:

I have actually made a dedicated video for this problem so I will put a link to it in the description of this video. The main reason people may have this problem is because we all like to rack that slide on our full blowback Airguns, but if you have a fully loaded magazine then each time you reach that slide without shooting the gun, you are inadvertently trying to load another BB into the breach area, the breach is only designed to hold one BB at a time so after a few racks of the slide the newly loaded have no place to go but into the Gas Tube where they can get stuck and cause having to the operation of your Full Blowback CO2 Airgun.

BB’s Rolling Out of the Barrel of Your CO2 Airgun:

This is not actually a fault of the gun but happens because of the way the gun is designed. This situation can happen with certain CO2 Airguns when the gun user pulls the trigger really slowly while the gun is point slightly in a downward position. What is actually happening is the first part of the trigger is made to draw a BB from the magazine into the breach of the gun. If the barrel of the gun does not have a rubber hop-up stopper in it then the BB is free to roll down the barrel and out of the gun. How do you fix this problem? Be more committed to your trigger pull and or shoot at a target that is not so low. Perhaps place your targets slightly higher than the gun so the barrel is not pointing down, especially if you like to take your time with the trigger :)

A Little Maintenance Can Go a Long Way!

Sometimes a good cleans is all you need to do to get things working as they should, again I have already made video Tutorial Showing “How to Clean Airguns and Blank Guns”.

What about stuff like My Airgun is jammed or my trigger is stuck or some random part fell out of my gun?

There is only so much I can cover in this video, most other problems are going to get a bit more complicated to fix and I suggest if your Airgun is not working and the suggestions I have made in this video do not solve your problem, then consider taking your gun into a gun tech.

First off I want to say it’s hard to trouble shoot technical or mechanical problems over the internet regardless of if ithas to do with guns, cars, computers or pretty much anything where unless you are there in person it’s really hard to figure out the problem.

But I will attempt to address some of the more common issues why a blank gun may not be functioning properly.

Why is my Semi Auto Blank Gun Not Cycling or Ejecting Shells?

One very common reason a blank gun may not be cycling the shells properly is because the owner has removed the barrel restrictor plug. People usually do this to make the barrel opening look more realistic but the barrel restrictor is a necessary component to increase the back pressure allowing the slide to cycle fully to the rear position so it can eject and pickup a new shell.

The blanks you are using may not have enough gun powder in them. Some blank guns require banks with more gun powder than others, again this additional internal pressure forces the slide all the way back, if the blank does not have enough gun powder in it then only a partial slide motion happens and so the discharged shell may not eject properly, in this case the user would have to clear the blank gun manually so another shell can then be picked up and loaded into the breach.

If your blank guns is dirty or not lubricated then it may act sluggish again restricting the full movement of the slide which will effect correct operation. Make sure to thoroughly clean and lubricate your blank gun, that may be a quick fix for you!

You may have a faulty extractor? The extractor is like a hook that grabs the discharged shell while the slide is in the reward position pulling or extracting the shell out of the breach. If the extractor is worn or broken then the empty shell will not be ejected from the breach so when a new shell is picked up from the magazine it has nowhere to go and usually you will get a jam-up in the ejection port area.

One final situation that can cause your blank gun to not cycle properly is to strong of a slide spring, some blank guns out of the box just come with a really heavy slide spring, so much so that even blanks with lots of gunpowder in them are still not strong enough to make the slide operate full motion. Your only option here would be to replace the heavy slide spring with a lighter one.

Why Are My Blanks Not Firing?

This is a situation where you pull the trigger and nothing happens. Lets get the obvious causes right out of the way here… Did you put blanks in your gun and are they new blanks? Did you chamber the first round in your semi auto pistol?

So now that that’s out of the way let’s look at some other reasons why your blank gun may not be firing a blank. Perhaps the firing pin is broken? Most blank guns are not made out of carbon steel and even the firing pins can be lesser quality than what you would find in a real gun so blank guns are more prone to breaking than real guns. I have seen broken firing pins in blank guns first hand so make sure to check the firing pin and that it is fully operational.

Try changing up your blanks to another brand? Again blank gun ammunition is not made to the same higher standards that real firearm ammo is made and some primers may require a little more pressure than your gun is providing. Even with real guns an ammo change may help the gun operate better.

Why is the Trigger or Hammer Not Operating Properly?

I have come across blank guns where there are mechanical problems in the trigger and hammer areas, you may be able to address this yourself but I would recommend taking your blank gun to a gunsmith since you will have to take the gun pretty much full apart to fix a problem in the trigger and hammer areas.

Of course make sure your gun is clean and lubricated, this can help a lot with the mechanical areas of your blank gun.

One problem I saw with a few EKOL Special 99’s was specifically with the single action potion of the trigger, when I would pull the hammer back it would not lock back and the hammer would often slip and fire randomly, this is rather dangerous. When I took the gun apart I found that the table top or step that the trigger was supposed to catch on was worn down on the edge so it would simply slip off. I was able to fix this by filing a new edge on the step area. Again this can happen because blank guns are not made out of as high quality metal materials as real guns.

Why does the Flame Come out the Top of My Blank Gun and Not the Front?

If you find that the flame or discharge comes out of the top of your blank gun and not the barrel, this usually does not mean anything is wrong with your blank gun. All it means is you own a top venting blank gun and not a front firing blank gun. In some countries front firing blank guns are not allowed but front venting blank guns are. The same may also be reversed in some countries, for instance here in Canada we can only import front firing blank guns with flare adaptors since our blank guns are imported under the assumption that they are to be used as signaling or flare devices.

Can I Convert my Top Venting Blank Gun into a Front Venting Blank Gun?

I really don't recommend altering a blank gun in any way as it may be a violation of your local laws and it could cause the blank gun to malfunction in a very bad way causing serious injury or even death!

In theory I suppose it may be possible to convert your Top Venting Blank Gun into a Front Venting Blank Gun but again you would need to allow for just the right amount of back pressure so a wide open barrel would not work unless it was a revolver. You can not simply remove the red plug and bingo you have a front firing blank gun because in most cases the barrel will be completely plugged in the frontal region. Not only would you need to drill out the plugged portion of the barrel but you would also have to somehow fill in the top venting area and again makes sure to allow for just enough back pressure to cycle the slide back and forth.

Hopefully this has helped some of you with blank gun issues. If you’re looking for a blank gun make sure to come down to www.ReplicaAirguns.ca and www.ReplicaAirguns.us and have a look in our blank gun area of our online stores.

Power Sources Covered in this review: CO2 - Spring Piston - Variable Pump -HPA (High Pressure Air)

Pro’s:

• CO2 Airguns allow for fast repeat shooting, great for action shooters, generally CO2 Airguns will supply a medium power range. No need to pump or cock your CO2 powered weapon in-between shots and a CO2 power source can allow for a very realistic action of the gun you are shooting.

• Spring Piston Airguns are best suited of single shot situations, they can provide low to high power output depending on the spring used. Spring Piston Airguns are very low cost to operate since you only need to buy the Pellets or BB’s. Spring Piston Airguns are not greatly effected by outside temperatures.

• Variable Pump Airguns allow you to decide how much power your gun will have and can offer very high power output depending on the Airgun. Variable Pump Airguns are very low cost to operate since you only need to buy the Pellets or BB’s. Variable Pump Airguns are not greatly effected by outside temperatures. Variable Pump Airguns generally have very low recoil and vibration.

• HPA (High Pressure Air) Airguns generally do not require pumping or cocking in-between shots and some even come in semi automatic or bolt action. HPA Airguns can have very high power output and even be used on larger game using large caliber ammunition. HPA Air Rifles have lower recoil and low vibration. HPA Airguns can be charged ahead off time so they are ready for use when you need them.

Con’s:

• CO2 Airguns require the additional cost to buy the CO2 as they do not function without it. CO2 Airguns have a limited power output and lose power as you shoot and use up the CO2. CO2 Airguns are effected by hot and cold temperatures and will have less power in colder temperatures and may not even work in super cold environments.

• Spring Piston Airguns require cocking before each shot. Spring Piston Airguns can have a lot of recoil and vibration, so much so that special optics must be considered when buying an optical sight. The action of the spring recoil can effect accuracy, especially if you are not use to the vibration and recoil or have spent some time practicing using a Spring Piston Airgun.

• Variable Pump Airguns will require multiple pumps to achieved maximum power output which can take some time in-between shots. So you are going to have to work for each shot.

• HPA (High Pressure Air) Airguns require the use of a manual pump to fill their built in air tank to maximum pressure and it does take a lot of time to manual fill an HPA tank. Alternatively you can have the air tank filled at a shop or buy a pressurization system similar to a scuba tank out paintball setup, the cost of this setup can be very high but will save you the castle of manually pumping air in to your HPA Airgun. HPA Airguns are generally a little more bulky then other Airgun systems since they have to accommodate fairly large air pressure tanks.

I already made several review videos for both Gletcher NGT (4.5mm Steel BB) and the Gletcher NGT R (.177 Cal Pellet) Revolvers, including table top and shooting videos. So make sure to check those videos out for more information on both versions of Gletcher NGT and NGT R Revolvers.

I did however miss some noteworthy details that I wanted to cover in this video. Firstly, the real steal Nagant M1895 Revolver this Gletcher NGT is styled after has a very unique gas-sealing system that the Airgun version does not replicate or really require but it is worth mentioning.

Here is some more info on how the original Nagant M1895 Revolver Gas Seal System works:

(From Wikipedia) The M1895 by contrast, has a mechanism which, as the hammer is cocked, first turns the cylinder and then moves it forward, closing the gap between the cylinder and the barrel. The cartridge, also unique, plays an important part in sealing the gun to the escape of propellant gases. The bullet is deeply seated, entirely within the cartridge case, and the case is slightly reduced in diameter at its mouth. The barrel features a short conical section at its rear; this accepts the mouth of the cartridge, completing the gas seal. By sealing the gap, the velocity of the bullet is increased by 15 to 45 m/s (50 to 150 ft/s.) This feature also eliminates the possibility of injury through the dangerous expansion of gases from the cylinder behind the barrel, which are easily capable of severing a finger if the user holds the gun incorrectly (with a finger positioned in front of the cylinder during fire) - a noted safety-issue in conventional revolvers.

Moving on to some of the features incorporated into the Gletcher NGT NGT-R CO2 BB and Pellet Revolver that I did not point in any of my previous videos. There is an extractor rod that can be used to extract a shell, this is not really necessary on the airgun version since the shells do not expand and tighten on the cylinder as they would n the real steal Nagant M1895 Revolver built is nice that we can replicate this feature with the Airgun version. You can also remove the cylinder completely from both the BB and Pellet shooting Gletcher NGT NGT-R CO2 Revolvers. The cylinder is actually very heavy and adds a lot of weight to this compact 7 shot Revolver.

It is always nice when an Airgun is built in such a way that it replicates the real steal version as closely as possible and the Gletcher NGT NGT-R CO2 BB and Pellet Revolvers do this nearly perfectly.

Buy Gletcher NGT Revolvers in Canada

Buy Gletcher NGT Revolvers in the US

I get asked on a daily bases form many of my Vimeo Viewers about how and if there is a way to get rid of the White lettering on Airguns, Typically people are wanting to remove the intrusive Warning instructions from Airguns like the Cybergun Tanfoglio Witness 1911, the Cybergun/Swiss Arms GSG 92/P92 and many other CO2 Replica Airguns that have lettering or branding that you may want to get rid of.

In this Instructional Tutorial Video I show you how can at least tone down the white lettering and even completely remove it on some Airguns without damaging the Airguns finish underneath the white lettering. You will have to use some patience and perhaps repeat this method a few times but the end result is worth the effort.

The magical product I use to remove the white lettering on many popular Airguns is a product from Birchwood Casey called the Presto Gun Blue Pen. This product is actually designed to touch up real steel gun in areas where the blueing has worn off, lucky for us the Birchwood Casey Presto Gun Blue Pen also works well to remove the ugly white lettering from Airguns.

I have often been asked which of the Shells for the Shell Loading Revolvers work in which Shell Loading Revolvers? After all many of them look a lot alike so can you mix and match Shells for the various types of Shell Loading Revolvers?

In this Vimeo Instructional Video I test out a bunch of Shells to see which ones actually will work or not work in several of the most popular Shell Loading Revolvers.

Some of the Shell Loading Revovers Tested in this Instructional Video are:

• Dan Wesson Classic Revolver (BB, Airsoft, Pellet)

• Dan Wesson 715 Revolver (BB, Airsoft, Pellet)

• Colt Single Action Army Peacemaker (BB, Airsoft, Pellet)

• Gletcher NGT and NGT-R (BB and Pellet)

• Webley Mark VI (BB)

• KWC 357 / Umarex 357 (BB, Airsoft)

• G&G G731 (Airsoft) 

When I say Airguns, I am referring to pretty much all BB, Airsoft, Pellet, Paintball and even Blank guns for most of the topics listed here.

Do’s:

1. Treat your Airgun just like you would a real gun. If something goes wrong, perhaps the outcome will not be as severe but do you really want to take a trip down to your local emergency ward to get a BB or Pellet removed?

2. Always assume your airgun is loaded, for some reason it always seems those empty guns are the ones that do the most damage.

3. Be discrete, If it looks like a gun other people will think it is a gun so don’t flash your airguns around in public. Keep it in a case when transporting and shoot it in an area that will not alarm other people.

4. Always wear eye protection when shooting your Airgun. Do you really want to shoot your eye out? No Joke!

5. Be aware of your surroundings like windows, hard objects that could make your ammo bounce back at you. Make sure you are shooting your Airgun in a safe direction at all times, know your target and beyond.

6. Use Airguns to teach others and learn how to safely and effectively shoot a gun. Airguns can be less intimidating then a real gun (Not so loud and very little recoil) and make for great start out and transitions guns.

7. Use Airguns to get more inexpensive trigger time and become a more experienced shooter. Airguns cosy only pennies per round to shoot and can be shot in way more areas than a real gun can, practice makes perfect so get shooting!

8. Use Airguns in areas where real guns may not be allowed or safe to use. Again, Airguns can be shot in all kinds of places, in your back yard or even in a properly setup indoor home range.

9. Use Airguns with adequate power for safe and humane pest control where real guns may be prohibited.Airguns are quiet and less likely for the bullet to travel long ranges which makes them ideal for close range pest control in areas where real guns are too loud and to powerful.

Don’ts:

1. Do not assume because it is an airgun it is not dangerous or simply a toy. Many Deaths have been caused by Airguns along with a lot of pain and suffering so treat your Airgun with respect. It is not a toy or you would find them in the toy department at your local store along with yo-yos and stuffed animals.

2. Do not point or shoot at people unless of course you are using an Airsoft gun in an Airsoft field or facility. Yes Airsoft guns are meant to shoot at each other (with appropriate attire like eye protection and full body clothing), but steel BB and Pellet can cause serious injury especially at close range and on direct skin contact.

3. Do not leave your Airgun loaded, you never know who is going to come across it and accidentally discharge it. Remember, a loaded gun is a dangerous gun in the wrong hands. You may know better than to assume the gun is undulated but children and even adults without any gun training will most definitely handle the airgun without consideration of the danger it poses.

4. Do not use an Airgun for self protection. See my related video. Simply put, Airguns are not practical for self defense because they rarely have enough Stopping Power. The ones that do have enough power need to be pre-charged and in most cases are only single shot meaning if you miss or don’t get the job done no the first shot then you are done.

5. Do not use an underpowered Airgun for pest control. See related video. Using a low powered BB pistol for pest control is cruel, you will only injure the animal making it suffer unnecessarily. Use a high powered pellet rifle to get the job done.

6. Do not take your gun apart, in most cases this will void the warranty and the reality is that airguns rarely need to be cleaned since no dirty gun powder is used. lead pellet rifles may require occasional barrel cleaning to keep the rifled barrel free of debris.

7. Do not over oil your Airgun, a little goes a long way and too much oil will just attracted dirt, use the right airgun oil and just enough to keep part functioning smoothly.

8. Do not over pump an Airgun. Over pumping an Airgun can cause damage to valves and seals and in a worse case situation a rupture the air pressure reservoir or even cause the airgun to explode!

With the popularity of the KWC - Cybergun 1911 Blowback CO2 Pistols and how super realistic they are in so many ways, it is no surprise that people often ask me if they can replace the original grips with grips made for a real 1911.

The short answer is yes you can! You will have to be prepared to remove just a little bit of material from the backside of both grips near the bottom of the handle where there is an area that has been flared out to accommodate the CO2. Not really a big deal, you can use a Dremel for the quick and easy approach or even some sand paper if you don't mind taking a little more time.

In this Vimeo Video I demonstrate using grips that fit a real 1911 and show you just exactly where you will need modify them to fit on the KWC and Cybergun CO2 Blowback 1911 pistol series.

Buy the KWC Blowback CO2 1911 BB Pistol in Canada