View fullsize

Airguns are not toys and as so require proper storage, transportation and handling so as not to cause an accident that could be minor or even deadly.

No matter if you are handling an Airgun or a “Real Gun”, they should both be handled in the same manner even if the consequences from an accident with an Airgun may be less serious. Life long injuries like the loss of an eye are nothing to be taken lightly.

For the most part, what I talk about in this Airgun Safety 101 video can also be applied to a “Real Gun” although most countries will have stricter laws and guidelines in the storage, transportation and handling of “Real Guns” over an Airgun.

View fullsize

Storing Your Airgun:

In Canada an unregulated Airgun does not have any real specific safe storage guidelines but common sense should be used and I recommend that you at the bare minimum keep your Airgun in some sort of locked space whether it be a safe, cabinet or room that is locked all of the time.

You can also put a trigger lock on your Airgun if you do not have a lockable storage location for it.

You should also make sure to store your Airgun unloaded, at least when it comes to BB’s and or Pellets. If there is some unused CO2 in it, or it is charged with Compressed Air, but unloaded in terms of ammunition, that is OK, but again keep it in a safe location away from anyone that may be able to get their hands on it and hurt themselves or others.

View fullsize

Transporting Your Airgun:

Again, in Canada an unregulated Airgun does not have any real transportation guidelines but if you keep your Airgun out in the open and someone sees it, they will most certainly call the police and more than likely you may find yourself staring down the wrong end of a police firearm, at least until they sort it all out. This is very serious as unfortunately people have died as a result of handling their Airguns out in the open and underestimating what kind of police response that may entail.

For that reason alone, always keep your Airgun out of sight in a case or backpack or the trunk of your car. Never transport your Airgun loaded and it is best if you can lock it in a case or put a trigger lock on it for added safety when transporting it.

View fullsize

Shooting Your Airgun:

Shooting your Airgun is always the most enjoyable part of owning an Airgun, so don’t do something stupid and turn that experience into a nightmare. Treat your Airgun as if it is deadly at all times, never point it at anything you do not intend on shooting.

Keep your safety on until you are ready to shoot. Never put your finger on the trigger until you are ready to shoot it and only shoot it in a safe location with an appropriate background and backstop.

Think of the barrel of your Airgun as a light saber that if it crosses even your arm, it could cut it off. Even a BB to the arm is a serious matter. I had a friend that shot himself in the arm with a BB Gun and the BB lodged in the tendons of his wrist requiring an operation to remove it. He was a violin player so this could have ended his violin playing, but luckily he was OK.

When Your finger is not on the trigger it should be held across the trigger guard in a straight position to ensure no accidental misfires.

Wear eye protection, Steel BB’s will bounce back when they hit a hard surface and can come back with enough force to injure an eye easily. Generally Airguns do not require ear protection but some can be loud enough that you may want to wear some sort of ear protection as a precaution.

Only shoot with others that are responsible and take Gun Safety very seriously. Young people will need constant supervision and it is best to go through all of this first before even considering handing them an Airgun for the first time. Perhaps start them off with something like an Airsoft gun which will have less consequences if an accident were to take place.

Airguns are awesome in so many ways and allow for a similar shooting experience to a “Real Gun”. They can be used in more situations, with less overall cost and are a great way to learn proper gun handling and how to improve your shooting ability even if you are a “Real Gun” owner. Always be responsible with your Airgun not only for yourself but for others as it only takes a few idiots to ruin things for the rest of us. Don’t be that Idiot please!

• Buy Airguns in Canada

• Buy Airguns in the US

There are many types of magazines used in Airguns and some of this is dependent on the ammunition used.

For instance a stacked type of magazine often used for Steel BB and Airsoft can not be used for Pellets as pellets tend to deform when stacked in such a way since there is no metal casting protecting them from mashing into each other.

So what type of magazines do we generally see in Airguns? The most common Airgun magazines are as follows:

Simple Stick Magazine

• Mostly used with Steel BB but also found in some Airsoft Airguns.

• Some Pellet Airguns use a type of stick magazine with a rotary magazine on each end.

• Used in non-blowback and blowback Airguns.

• Can be made from plastic or steel or a combination of both materials.

Full Size Drop Out Magazine

• Used with Steel BB and Airsoft guns.

• Generally you will find these types magazines hold both the BB’s and CO2.

• Used in non-blowback and blowback Airguns.

• Commonly used with Airsoft Rifles in mid to high capacity.

• Can be made from plastic or steel or a combination of both materials.

Rotary magazine

• Used with Steel BB, Airsoft and Pellet Airguns.

• Used in non-blowback and blowback Airguns.

• Can be made from plastic or steel.

• Can often use mixed ammo types as in both 4.5mm Steel BB and .177 caliber pellet.

Belt Fed Magazine

• Like rotary magazine belt fed magazine can accommodate Steel BB, Pellet and Airsoft but are most often used with Pellet Airguns.

• Usually found in a full size magazine that also holds the CO2.

• Used in non-blowback and blowback Airguns.

• Can be made from plastic or steel or a combination of both materials.

Internal Magazine

• Used with Steel BB, Airsoft.

• Can have a hopper built in hat feeds a spring fed magazine.

• Usually found in lesser expensive Airguns but not a rule.

In this Video I go through each type of Airgun Magazine and talk about their differences and uses.

View fullsize

Type: Arrow Rifle.
Manufacturer: Umarex
Model: AirSaber Elite X2.
Materials: Metal and Polymer.
Weight: 8.7 pounds (3.9kg).
Air Tank: 4000 PSI - 240cc.
Barrel: Double barrel system.
Propulsion: PCP (Compressed Air).
Action: Side cocking - Single action trigger.
Ammunition Type: 350 grain Arrows.
Ammunition Capacity: 2.
Max FPS: 450 Claimed.

View fullsize

Trigger Pull: The trigger on the Umarex AirSaber Elite X2 Double Barrel PCP Arrow Rifle is single action only requiring you to engage the side cocking latch system before you can shoot it. You will also be required to manually select the barrel using the side mounted cross bolt between shots. The trigger feels pretty light in general since it is a single action only trigger but it does have a fair amount take-up and creep before releasing.

View fullsize

Accuracy: I have not performed any shooting tests with the Umarex AirSaber Elite X2 Double Barrel PCP Arrow Rifle as of yet and I am not sure if I will since this product does require a high powered crossbow type backstop which I do not have at this time. I want to make sure I have a safe shooting environment before unleashing 169 foot pounds of energy downrange. I would imagine since the Umarex AirSaber Elite X2 Double Barrel PCP Arrow Rifle is designed more for mid to large game hunting that it will be accurate out to mid and long ranges, of course you will need to practice at the ranges you will be shooting at to know how the arrow will fly and how much elevation you will need to to adjust for.

View fullsize

Build Quality: The Umarex AirSaber Elite X2 Double Barrel PCP Arrow Rifle is really well built and solid coming in at 8.7 pounds. For it’s size it is not heavy since it ustilizes a combination of metal, aluminum and polymer. All the mechanical parts feel high quality and reactive.

View fullsize

Realism: The Umarex AirSaber Elite X2 Double Barrel PCP Arrow Rifle is not a replica of any real steel gun in production since it is a hunting rifle through and through. It is rifle shaped of course since that is what we have gown accustomed to using and so why change the main design. If you have used a rifle before then you will have no problem using the Umarex AirSaber Elite X2 Double Barrel PCP Arrow Rifle as it is more of a rifle and less of a bow or crossbow to use. It just happens to shoot arrow rather than bullet.

View fullsize

Pros:

• Canada non PAL Airgun with enough power to hunt medium to larger game!

• Overall price point is good, nothing like this to compare to.

• Arrows are propelled from the front, so no archers paradox when aiming.

• Arrows come with field tip arrows but can be unscrewed and replaced with broad tip arrow heads for hunting.

• Easy to use cross bolt safety on trigger.

• Pistol grip allows for easy hold and control.

• Fit and finish is excellent.

• PCP for more power and consistency than CO2.

• Picatinny rails on top for scope, sides and bottom for other accessories.

• Rubber butt-plate for added comfort.

• Improved easy to use side cocking system.

• Double barrel allows for quick follow up shot.

• Higher PSI for high power with same amount of shots as older single barrel AirSaber.

Cons:

• Need a pump or other compressed air-fill system.

• Will require a proper backstop system to practice safety with.

• Arrows are not cheap so make sure of your shots.

View fullsize

Comments:
The Umarex AirSaber Elite X2 Double Barrel PCP Arrow Rifle is a really unique product that allows virtually anyone to be able to hunt even larger game without a firearms license in Canada. It is not really a riffle or a crossbow, it is it’s own creation that takes the best of a rifle and the best from archery combining both into an easy to learn and use way to be able to hunt proficiently and perhaps even in areas rifles are not allowed to go. For the extra $100 or so I would recommend the Umarex AirSaber Elite X2 Double Barrel version over the original single version barrel but both will get the job done at the end of the day since usually your first shot is your only shot.

• Buy the Umarex AirSaber Elite X2 Double Barrel PCP Arrow Rifle in Canada

• Buy the Umarex AirSaber Elite X2 Double Barrel PCP Arrow Rifle in the US

In this Preview Unboxing Video I take a look at three rifles, two are Airsoft Rifles and one is an Archery Rifle. Then First Airsoft Rifle form Tokyo Marui i s full Gas Blowback all metal build AR 15 of the highest quality and realism while the second Airsoft Rifle from Sig Sauer is an AEG but again a high quality product for sure. Lastly I take a look at Umarex’s lates Airsaber which now sports dual Arrow configuration for quick follow up shots. I do plan to make future more intensive table top and shooting videos for some if not all of thees Rifles but this video will at least wet your appetite a bit.

View fullsize

Tokyo Marui CQBR Block 1 GBB Airsoft Rifle:

• Type: GBB Airsoft

• Caliber 6mm Airsoft

• FPS: 350-400

• Magazine Capacity: 35

• Weight: 9.9 pounds

• Length: 27.5 inches

• Material: Mostly Metal

• Action: Semi & Full Auto

View fullsize

Sig Sauer Proforce MCX Virtus AEG Airsoft Rifle:

• Type: AEG Airsoft

• Caliber 6mm Airsoft

• FPS: 420

• Magazine Capacity: 120

• Weight: 7 pounds

• Length: 29 inches

• Material: Mostly Metal

• Action: Semi & Full Auto

View fullsize

Umarex Airsaber Elite X2 Archery Rifle:

• Type: PCP Archery

• Capacity: 4000 PSI / 240 CC Tank

• FPS: 450 / 169 ft-lbs

• Ammo Capacity: 2

• Weight: 8.7 pounds

• Length: 42.5 inches

• Material: Metal & plastic

• Action: Side cocking lever

View fullsize

This was an unusual Field Test Review for me to do as I really don’t test out Bows or Crossbows all that much and I don’t have the best backstop setup for doing such reviews. So I spent some time making a backstop that was capable of stopping these just over 6 inch almost 10 gram or 150 grain bolts. It required some layers of foam and cardboard along with a blanket behind just in case, and even with this setup the bolts managed to lodge themselves right up to the Fletching (feather part of the arrow). Also make sure to watch my Table Top Video Review for the Bear X Desire XL Crossbow to see it up nice and close and get all the specifications and features.

I kind of wanted to change up this review just a bit and so I recorded my Chronograph Velocity at the same time as I did my Target or Accuracy Test to simplify things. I used 5 bolts in all and got what I felt was a good result using the Bear X Desire XL Crossbow.

In terns of velocity Bear X claims that the Bear X Desire XL Crossbow will shoot around 175 fps. I was able to get consistent 190+ fps readings using the 147 grain 6.5 inch aluminum bolts with my lowest fps being 192 and the highest being 194 so super consistent. This gave an overall Foot Pound energy of 12.4 foot pounds! This is enough for small pests for sure, it really comes down to accuracy at this point as you will want to get either a head or shoulder area shot for a humane kill.

View fullsize

I did do a pre test to make sure I was on target and duding this test I was able to get about a 5 inch 5 shot grouping. During my recored Accuracy Test this did open up a bit as one arrow went high and to the right so if I leave that arrow out of the test I did manage to get another 5 inch grouping with three of the arrows all within 1.5 inches of each otter. I figure with high quality arrows and some practice time using the Bear X Desire XL Crossbow, you should be able to use it for small pest control at least at closer in ranges.

All in all the Bear X Desire XL Crossbow surprised me with how powerful it really was and with the accuracy using standard default bolts. This is for sure not a toy and you would never want to accidentally shoot this at someone as it could cause a very serious injury or even death and I mean that since these arrow would for sure pierce several inches into the body. So if you’re looking for something with a bit more raw power than your standard non-regulated Airgun, then check out the Bear X Desire XL Crossbow over in both our Canada and US Online Replica Airguns Stores.

• Buy the Bear X Desire XL Crossbow in Canada

• Buy the Bear X Desire XL Crossbow in the US

View fullsize

Type: Compact Crossbow.
Manufacturer: Bear X.
Model: Desire XL.
Materials: Metal & plastic.
Weight: 2.3 pounds (1 kilograms).
Length: 20-22 inches.
Propulsion: Bow.
Action: Single action trigger.
Ammunition Type: Aluminum bolts (Comes with 3).
Ammunition Capacity: 1.
FPS: 175fps.
Draw: 60 pounds

View fullsize

Trigger Pull: The trigger pull on the Bear X Desire XL Crossbow is medium to heavy, it is a single action only trigger as you need ot cock the bow in order for the trigger to be engaged. The safety is also engaged when you cock the bow requiring you to take the Bear X Desire XL Crossbow off safe before shooting as an added layer of safety.

View fullsize

Accuracy: I have not made my Field Test Shooting Video for the Bear X Desire XL Crossbow and so I have not sea what to expect for it. I have watched a few videos of other people reviewing it and it looks to perform fairly well but until I get a few bolts in a target downrange I can not say for certain the accuracy of the Bear X Desire XL Crossbow. I will have to figure out some sort of a usable back stop in order to make this Field Test Shooting Video but have some ideas already on material to use as my back stop. FPS is claimed ot be around 175 and I will be doing my best to Chronograph the Bear X Desire XL Crossbow so we can confirm that rating for ourselves…

View fullsize

Build Quality: The Bear X Desire XL Crossbow is actually made pretty decently, yes it is mostly plastic and light weight but feels sturdy enough to hold, the only real metal I can confirm is the cocking rail, mostly everything else other than the nuts and bolts that hold it together are some sort of plastic, the bow itself may be a composite material but I am not sure what exactly it is?

View fullsize

Realism: The Bear X Desire XL Crossbow is not a Replica as is what I usually review here on the channel. But I think their is a crossover in terms of interest for a product like this with people that are also interested in airguns. I know I like the Bear X Desire XL Crossbow and can see a place for it in my collection even if it’s not a replica product.

View fullsize

Pros:

• Fairly inexpensive.

• Super light weight.

• Can shoot in a variety of situations.

• Easy to draw the bow.

• Safety is automatically engaged.

• Picatinny rail already has iron fully adjustable rear sight but can mount a red dot if you like.

• Fiber optic front sight.

• 3 bolts included.

• 175 fps (not sure of the ft/lbs)?

• Comes with fore grip.

• 3 portion adjustable rear but stock.

View fullsize

Cons:

• Will need a good backstop or will lose or damage a lots of bolts.

• Takes a little bit of time to set it up but not too hard if you follow the instructions.

View fullsize

Comments:

The Bear X Desire XL Crossbow is an interesting product that once purchased and if you manage to not lose the bolts will cost virtually nothing to shoot since you can reuse the bolts all day long given you shoot them on target and that target does not damage the bolts. It may not offer the rapid fire action shooting of a replica semi auto CO2 Pistol but still challenges the shooter in terms of getting the best possible accuracy out of it and at the end of the day trigger time is trigger time! If you are looking for something a bit different than your CO2 Air Gun then maybe the Bear X Desire XL Crossbow will fill that requirement.

• Buy the Bear X Desire XL Crossbow in Canada

• Buy the Bear X Desire XL Crossbow in the US

In this Preview Unboxing Vimeo Video I take a look at five very different products! A Spring Piston .177 Caliber Pellet Pistol, an Airsoft GBB Pistol, a Compact Crossbow, a full auto CO2 Blowback BB Pistol and a PPC .22 Caliber Pellet Rifle.

View fullsize

First up is the Umarex Ruger Mark IV Spring Piston Pellet Pistol which is a single shot replica pellet pistol that shoots .177 caliber pellets at up to 320 fps using a spring piston break barrel system. The Umarex Ruger Mark IV Spring Piston Pellet Pistol is a target plinker with fully adjustable fiber optic sights and should be a lot of fun to shoot!

View fullsize

Next I take a look at a Gas Blowback Airsoft Pistol from Action Army that closely resembles the Ruger Mark IV pistol with perhaps a more compact look. The Action Army AAP-01 GBB Airsoft Pistol is full blowback a full size drop out magazine and fiber optic sights. It also come with a threaded barrel and barrel extension for adding a longer barrel and much suppressor.

View fullsize

Next on my list of new items is the Bear X Desire XL Crossbow which is a 2.2 pound compact bolt shooting crossbow that sports a rail system with included adjustable iron sights that also allow for a red dot if you want to really customize it. The Bear X Desire XL Crossbow has a 60 pound draw and shoots arrows/bolts at up to 175 fps.

View fullsize

Another AR BB Rifle/Pistol from Crosman is the Crosman A4-P Full Auto CO2 BB Pistol which is essentially a pistol version of the AR Platform. If you like the Crosman DPMS SBR, R1, PDW then you will probably also like the Crosman AP-4. Like the others it uses dual CO2’s and shoots 4.5mm Steel BB;s in semi or full auto at 1400 rounds per minute until the 25 round magazine is empty.

View fullsize

Last included in this preview video is the Air Venturi Avenger Regulated PCP Pellet Rifle. I’m a bit uncertain about this one as I am pretty sure it is the non detuned PAL version that requires a firearms license here in Canada as it shoots at full velocity (.22 caliber pellet at 950 fps). If that’s the case then it will not be available in our Canada Replica Airguns Store but may be available in the US Replica Airguns Store. If it is the detuned version or a detuned version becomes available in Canada then I imagine we will at some point have it in the Canada replica Airguns Store. That said the Air Venturi Avenger Regulated PCP Pellet Rifle uses compressed air and shoots either .177. .22 or .25 caliber pellets using a latch system and rotary magazine.

View fullsize

For this Field Test Shooting Video I actually had to go outside and use my field so in order to have an appropriate amount of distance to properly test the Umarex AirJavelin Archery CO2 Arrow Rifle. My Indoor Airgun Shooting Range is only 30 feet long and my metal backstop was simply not usable for the arrows.

I setup a make ship arrow backstop using a large bag of bark mulch with a rubber matt over top. This setup seemed to work really well for the Umarex AirJavelin Archery CO2 Arrow Rifle allowing the arrows to stick in most of the way. My target was setup around 55 feet away and I was using rested but standing shooting position for my testing.

View fullsize

I decided to combine the Chromo and Accuracy portion of my Field Test Shooting Video for the Umarex AirJavelin Archery CO2 Arrow Rifle by recording each shot on my chronograph while I placed shots on target, why not right? I placed 6 arrows on target with 5 of my shots being recorded by the chronograph. The average fps was only 156, the highest being 183 and lowest being 136. I did experience a bit of a CO2 leak when I first placed my 88 gram CO2 in the Umarex AirJavelin Archery CO2 Arrow Rifle. I believe this was because I did not pull the bolt back which allowed the valve mechanism to be open slightly. I realized this fairly quickly and pulled the bolt back which saved most of the CO2 but I did lose a some. This may have lowered the fps a little bit but I was surprise that the Umarex AirJavelin Archery CO2 Arrow Rifle was recording about half the fps claimed by Umarex. That said the effectiveness of the arrows and penetration into the backstop would for sure get the job done if I was trying to eradicate some small to medium sized pests.

View fullsize

In terms of accuracy I was very impressed with the Umarex AirJavelin Archery CO2 Arrow Rifle. At 55 feet or so I was able to get 5 of the arrows all within 2-3 inches of each other, I did have one arrow drop a little bit lower than the main grouping. I’m not sure if I would want to shoot a pest out at 50-60 feet but it could be done with the Umarex AirJavelin Archery CO2 Arrow Rifle especially if you where to add a nice red dot or optical sight to it. I would think the Umarex AirJavelin Archery CO2 Arrow Rifle would be best suited shooting small to medium game at 30-40 feet which should allow for sub 2 inch groupings.

View fullsize

All in all the Umarex AirJavelin Archery CO2 Arrow Rifle performed well and was a lot more accurate then I was expecting it to be. I was a bit disappointed with the fps as I was hoping for something between 200-300 but again this may have been as a result of low CO2. If your looking for something for small to medium pest control at ranges up to 50 feet or so the Umarex AirJavelin Archery CO2 Arrow Rifle will get the job done nicely. You can also checkout my Table Top Review where I show you around the Umarex AirJavelin Archery CO2 Arrow Rifle and the Umarex AirSaber Archery PCP Arrow Rifle.

• Buy the Umarex AirJavelin Archery CO2 Arrow Rifle in Canada

• Buy the Umarex AirJavelin Archery CO2 Arrow Rifle in the US

View fullsize

Type: Archery.
Manufacturer: Umarex.
Model: AirJavelin & AirSaber.
Materials: Metal & polymer construction.
Weight: 3.9 pounds / 6.3 pounds no scope.
Foot Pounds Energy: 34 ft/lbs / 124 ft/lbs.
Total Length: 34 inches / 41 inches.
Propulsion: 88 gram CO2 x1 / PCP 3625 PSI, 250 cc.
Action: Bolt single action.
Ammunition Type: Carbon fiber 190 grain / 350 grain arrows (Field tip can be swapped over to broad-head)
Ammunition Capacity: 1 Arrow.
Max FPS: 300 / 450.

View fullsize

Trigger Pull: The trigger pull on both the Umarex AirJavelin and the Umarex AirSaber are both single action that require the bolts to be pulled back in order to shoot them. The Umarex AirJavelin trigger is not as short, light or crisp as the Umarex AirSaber, the Umarex AirSaber for sure feels higher quality as expected.

View fullsize

Accuracy: This is going to be very interesting as I have never shot anything like this before but from what I was told at SHOT Show this year I can expect very accuracy results from both the Umarex AirJavelin and the Umarex AirSaber Archery CO2 and PCP Arrow Rifles. I’m not sure if I will test the Umarex AirSaber unless I can make a safe shooting range for it, luckily I live out on average so as long as I can setup a good backstop I should be able to test them both.

View fullsize

Build Quality: The build quality of the Umarex AirJavelin and the Umarex AirSaber Archery CO2 and PCP Arrow Rifles is very good overall, the Umarex AirJavelin is mostly plastic and is not very heavy but the fit and finish is good all round. The Umarex AirSaber on the other hand has a lot of metal used in the construction, the only real plastic found on the Umarex AirSaber would be in the stock. The Umarex AirSaber is for sure a step up in quality over the Umarex AirJavelin but will cost you almost double in the end.

View fullsize

Realism: This is going to be pretty short section since both the Umarex AirJavelin and the Umarex AirSaber Archery CO2 and PCP Arrow Rifles are not replicas of any actual gun in production. Their primary use is going to be for hunting and or pest control I would say.

View fullsize

Pros:

• Only Canada non PAL Airguns with enough power to hunt medium and larger game.

• Overall price point is good, nothing like this to compare to.

• Arrows are propelled from the front, no archers paradox when aiming.

• Arrows come with field tip arrows but can be unscrewed and replaced with broad tip arrows for hunting.

• Easy to use cross bolt safeties.

• Pistol grips allow for easy hold and control.

• Fit and finish is very good and excellent on the AirSaber.

• AirJavelin: 88 Gram CO2 for quick easy use.

• AirSaber: PCP for more power and larger game options.

• AirJavelin: White dot up front with fully adjustable peep sight on back.

• AirJavelin: M-Lock on sides for adding accessories.

• AirSaber: Picatinny rails on top for scope, sides and bottom for accessories.

• AirJavelin: Adjustable AR-style rear stock.

• AirJavelin: Rubber buttplate for added comfort.

View fullsize

Cons:

• No scope or sights with base model AirSaber so you will need to get one for it.

• Not a lot of shots per 88 gram CO2, will need a pump for the PCP AirSaber.

• Arrows are not cheap so make sure of your shots.

View fullsize

Comments:
The Umarex AirJavelin and Umarex AirSaber Archery CO2 and PCP Arrow Rifles are very interesting in that they are really the only Canada legal “firearms” that can actually put down small, medium and even large game without requiring a firearms license (PAL). This is because they do not exceed 500 fps, they do exceed the foot pound energy limit of 4.2 foot pounds but since both of these rifles do not exceed the 500 fps limit they do not exceed both requirements to place them in the regulated firearms category that requires a firearms license. This is great news for anyone in Canada without a PAL license that wants to be able to hunt various game or take care of pests humanly. Umarex has also been kind enough to bring us two variations on this design. The Umarex AirJavelin more economical and easier to use CO2 powered version designed for small to medium sized game and the Umarex AirSaber higher quality PCP powered big brother version designed to be used even for larger game. Both are great, all you need to do is pick which one is right for you!

My Table Top Review for the Umarex AirJavelin and AirSaber Archery CO2 and PCP Arrow Rifles:

• Buy the Umarex AirJavelin Archery CO2 Arrow Rifle in Canada

• Buy the Umarex AirSaber Archery PCP Arrow Rifle in Canada

• Buy the Umarex AirSaber Archery PCP Arrow Rifle with Scope in Canada

I made a similar video about how to hold your airgun a while back but sometimes they get a bit buried in all the video I make. I feel it's really important how you grip your gun even if it's only an airgun with very little kick or recoil. Proper pistol grip is something you should use no matter what so that you can carry it forward to what ever gun you are shooting.

More kick or recoil means a firmer grip is required to hold the gun so when shooting a powder burner with lots of kick grip becomes even more important.

In this video I go over the proper two handed grip to use when holding a pistol, which hand to hold lose and which had to grip tight, how to overlap your fingers and thumbs.

One of the most common types of question I get on my Replica Airguns YouTube channel has to be something like… Why is my Airgun not working? Most of the time the amount of info about the problem is limited to something like… “It was working yesterday but now it’s not working anymore” or something like “when I pull the trigger nothing happens”. My personal favorite is… “I took my gun apart and now it doesn’t work!”

I just made a similar video for Blank Guns and as I said in that video, trying to trouble shoot a mechanical or technical problem over the internet is very difficult, this goes for cars, guns, computers or what have you…

In this Why is My CO2 Airgun Not Working video I will however cover some of the more common and obvious problems I have seen relating to why a CO2 Airgun may not be working properly. I really don’t get a lot of questions about Spring Piston or Pump Airguns so I will be focusing on CO2 Airguns in this video. There will be a lot of crossover with CO2 Airsoft guns so this video may be helpful for some of you Airsofters out there

First let’s get the super obvious stuff out of the way! 

• Did you put a new CO2 cartridge in it and is it pierced all the way?

• Did you load BB’s or Pellets into the Airguns magazine and is the magazine in the gun correctly?

• Is the safety off?

• If the gun is a blowback semi auto single action Airgun then did you pull the slide back prior to the first shot?

CO2 Related Problems:

Not all CO2 cartridges are created equal, they often have slightly different shaped nubs on them and some brands will work better than others in different Airguns. If the shape of the CO2 nub does not fit properly into the valve area then it may not pierce or it could pierce but then not allow you to tighten it all the way losing all the CO2 in the process. If the CO2 is coming form the airguns handle to CO2 Valve area then this is an indication that your problem is related to the area where the CO2 enters the airgun.

There is a seal where the CO2 cartridge buts up to the valve, this seal can be damaged or even deformed from usage or even leaving your CO2 in the gun for too long. The outside CO2 Valve seal can also take the shape of a specific CO2 nub so when you use a different brand CO2 the seal may not properly make concat with the new CO2 type you are using, again causing leaking or even the total loss of all your CO2. Watch my YouTube video on “How to Fix Leaking CO2 in an Airgun”.

CO2 Valve Related Problems:

Again, make sure that Outside CO2 Valve Seal is in good condition and any leaking is not being caused by this problem, if you have checked the Out Side Seal and everything is OK with it then perhaps there is a problem with the CO2 valve?

One indication that your CO2 Valve might be the culprit is the total loss of all your CO2 when you try to insert and tighten a new CO2 Cartridge. Usually all the CO2 will exit the barrel, not the handle or valve area. What may be happening is the valve is stuck open or the internal seal is broken or deformed. If this is the case you will have to remove the valve and have a look inside, this is a lot easier on CO2 airguns that have the CO2 valve in the magazine, if the CO2 valve is in the actual Airguns then a lot more disassembly may be required and I would recommend an Airgun technician take care of this for you.

If the gavel is in the magazine then you will have to unscrew it, you may require a special tool for this? Once the valve is out of the magazine  take a look inside and examine the internal seal, also look for any bits of metal shavings as they can disrupt the action of the valve causing leaking. Give the inside of the valve a good clean and then lubricate it with some silence spray. hopefully that fixes your problem!

BB’s getting Stuck in the Blowback Gas Tube:

I have actually made a dedicated video for this problem so I will put a link to it in the description of this video. The main reason people may have this problem is because we all like to rack that slide on our full blowback Airguns, but if you have a fully loaded magazine then each time you reach that slide without shooting the gun, you are inadvertently trying to load another BB into the breach area, the breach is only designed to hold one BB at a time so after a few racks of the slide the newly loaded have no place to go but into the Gas Tube where they can get stuck and cause having to the operation of your Full Blowback CO2 Airgun.

BB’s Rolling Out of the Barrel of Your CO2 Airgun:

This is not actually a fault of the gun but happens because of the way the gun is designed. This situation can happen with certain CO2 Airguns when the gun user pulls the trigger really slowly while the gun is point slightly in a downward position. What is actually happening is the first part of the trigger is made to draw a BB from the magazine into the breach of the gun. If the barrel of the gun does not have a rubber hop-up stopper in it then the BB is free to roll down the barrel and out of the gun. How do you fix this problem? Be more committed to your trigger pull and or shoot at a target that is not so low. Perhaps place your targets slightly higher than the gun so the barrel is not pointing down, especially if you like to take your time with the trigger :)

A Little Maintenance Can Go a Long Way!

Sometimes a good cleans is all you need to do to get things working as they should, again I have already made video Tutorial Showing “How to Clean Airguns and Blank Guns”.

What about stuff like My Airgun is jammed or my trigger is stuck or some random part fell out of my gun?

There is only so much I can cover in this video, most other problems are going to get a bit more complicated to fix and I suggest if your Airgun is not working and the suggestions I have made in this video do not solve your problem, then consider taking your gun into a gun tech.

First off I want to say it’s hard to trouble shoot technical or mechanical problems over the internet regardless of if ithas to do with guns, cars, computers or pretty much anything where unless you are there in person it’s really hard to figure out the problem.

But I will attempt to address some of the more common issues why a blank gun may not be functioning properly.

Why is my Semi Auto Blank Gun Not Cycling or Ejecting Shells?

One very common reason a blank gun may not be cycling the shells properly is because the owner has removed the barrel restrictor plug. People usually do this to make the barrel opening look more realistic but the barrel restrictor is a necessary component to increase the back pressure allowing the slide to cycle fully to the rear position so it can eject and pickup a new shell.

The blanks you are using may not have enough gun powder in them. Some blank guns require banks with more gun powder than others, again this additional internal pressure forces the slide all the way back, if the blank does not have enough gun powder in it then only a partial slide motion happens and so the discharged shell may not eject properly, in this case the user would have to clear the blank gun manually so another shell can then be picked up and loaded into the breach.

If your blank guns is dirty or not lubricated then it may act sluggish again restricting the full movement of the slide which will effect correct operation. Make sure to thoroughly clean and lubricate your blank gun, that may be a quick fix for you!

You may have a faulty extractor? The extractor is like a hook that grabs the discharged shell while the slide is in the reward position pulling or extracting the shell out of the breach. If the extractor is worn or broken then the empty shell will not be ejected from the breach so when a new shell is picked up from the magazine it has nowhere to go and usually you will get a jam-up in the ejection port area.

One final situation that can cause your blank gun to not cycle properly is to strong of a slide spring, some blank guns out of the box just come with a really heavy slide spring, so much so that even blanks with lots of gunpowder in them are still not strong enough to make the slide operate full motion. Your only option here would be to replace the heavy slide spring with a lighter one.

Why Are My Blanks Not Firing?

This is a situation where you pull the trigger and nothing happens. Lets get the obvious causes right out of the way here… Did you put blanks in your gun and are they new blanks? Did you chamber the first round in your semi auto pistol?

So now that that’s out of the way let’s look at some other reasons why your blank gun may not be firing a blank. Perhaps the firing pin is broken? Most blank guns are not made out of carbon steel and even the firing pins can be lesser quality than what you would find in a real gun so blank guns are more prone to breaking than real guns. I have seen broken firing pins in blank guns first hand so make sure to check the firing pin and that it is fully operational.

Try changing up your blanks to another brand? Again blank gun ammunition is not made to the same higher standards that real firearm ammo is made and some primers may require a little more pressure than your gun is providing. Even with real guns an ammo change may help the gun operate better.

Why is the Trigger or Hammer Not Operating Properly?

I have come across blank guns where there are mechanical problems in the trigger and hammer areas, you may be able to address this yourself but I would recommend taking your blank gun to a gunsmith since you will have to take the gun pretty much full apart to fix a problem in the trigger and hammer areas.

Of course make sure your gun is clean and lubricated, this can help a lot with the mechanical areas of your blank gun.

One problem I saw with a few EKOL Special 99’s was specifically with the single action potion of the trigger, when I would pull the hammer back it would not lock back and the hammer would often slip and fire randomly, this is rather dangerous. When I took the gun apart I found that the table top or step that the trigger was supposed to catch on was worn down on the edge so it would simply slip off. I was able to fix this by filing a new edge on the step area. Again this can happen because blank guns are not made out of as high quality metal materials as real guns.

Why does the Flame Come out the Top of My Blank Gun and Not the Front?

If you find that the flame or discharge comes out of the top of your blank gun and not the barrel, this usually does not mean anything is wrong with your blank gun. All it means is you own a top venting blank gun and not a front firing blank gun. In some countries front firing blank guns are not allowed but front venting blank guns are. The same may also be reversed in some countries, for instance here in Canada we can only import front firing blank guns with flare adaptors since our blank guns are imported under the assumption that they are to be used as signaling or flare devices.

Can I Convert my Top Venting Blank Gun into a Front Venting Blank Gun?

I really don't recommend altering a blank gun in any way as it may be a violation of your local laws and it could cause the blank gun to malfunction in a very bad way causing serious injury or even death!

In theory I suppose it may be possible to convert your Top Venting Blank Gun into a Front Venting Blank Gun but again you would need to allow for just the right amount of back pressure so a wide open barrel would not work unless it was a revolver. You can not simply remove the red plug and bingo you have a front firing blank gun because in most cases the barrel will be completely plugged in the frontal region. Not only would you need to drill out the plugged portion of the barrel but you would also have to somehow fill in the top venting area and again makes sure to allow for just enough back pressure to cycle the slide back and forth.

Hopefully this has helped some of you with blank gun issues. If you’re looking for a blank gun make sure to come down to www.ReplicaAirguns.ca and www.ReplicaAirguns.us and have a look in our blank gun area of our online stores.

I already made several review videos for both Gletcher NGT (4.5mm Steel BB) and the Gletcher NGT R (.177 Cal Pellet) Revolvers, including table top and shooting videos. So make sure to check those videos out for more information on both versions of Gletcher NGT and NGT R Revolvers.

I did however miss some noteworthy details that I wanted to cover in this video. Firstly, the real steal Nagant M1895 Revolver this Gletcher NGT is styled after has a very unique gas-sealing system that the Airgun version does not replicate or really require but it is worth mentioning.

Here is some more info on how the original Nagant M1895 Revolver Gas Seal System works:

(From Wikipedia) The M1895 by contrast, has a mechanism which, as the hammer is cocked, first turns the cylinder and then moves it forward, closing the gap between the cylinder and the barrel. The cartridge, also unique, plays an important part in sealing the gun to the escape of propellant gases. The bullet is deeply seated, entirely within the cartridge case, and the case is slightly reduced in diameter at its mouth. The barrel features a short conical section at its rear; this accepts the mouth of the cartridge, completing the gas seal. By sealing the gap, the velocity of the bullet is increased by 15 to 45 m/s (50 to 150 ft/s.) This feature also eliminates the possibility of injury through the dangerous expansion of gases from the cylinder behind the barrel, which are easily capable of severing a finger if the user holds the gun incorrectly (with a finger positioned in front of the cylinder during fire) - a noted safety-issue in conventional revolvers.

Moving on to some of the features incorporated into the Gletcher NGT NGT-R CO2 BB and Pellet Revolver that I did not point in any of my previous videos. There is an extractor rod that can be used to extract a shell, this is not really necessary on the airgun version since the shells do not expand and tighten on the cylinder as they would n the real steal Nagant M1895 Revolver built is nice that we can replicate this feature with the Airgun version. You can also remove the cylinder completely from both the BB and Pellet shooting Gletcher NGT NGT-R CO2 Revolvers. The cylinder is actually very heavy and adds a lot of weight to this compact 7 shot Revolver.

It is always nice when an Airgun is built in such a way that it replicates the real steal version as closely as possible and the Gletcher NGT NGT-R CO2 BB and Pellet Revolvers do this nearly perfectly.

Buy Gletcher NGT Revolvers in Canada

Buy Gletcher NGT Revolvers in the US

I get asked on a daily bases form many of my Vimeo Viewers about how and if there is a way to get rid of the White lettering on Airguns, Typically people are wanting to remove the intrusive Warning instructions from Airguns like the Cybergun Tanfoglio Witness 1911, the Cybergun/Swiss Arms GSG 92/P92 and many other CO2 Replica Airguns that have lettering or branding that you may want to get rid of.

In this Instructional Tutorial Video I show you how can at least tone down the white lettering and even completely remove it on some Airguns without damaging the Airguns finish underneath the white lettering. You will have to use some patience and perhaps repeat this method a few times but the end result is worth the effort.

The magical product I use to remove the white lettering on many popular Airguns is a product from Birchwood Casey called the Presto Gun Blue Pen. This product is actually designed to touch up real steel gun in areas where the blueing has worn off, lucky for us the Birchwood Casey Presto Gun Blue Pen also works well to remove the ugly white lettering from Airguns.

I have often been asked which of the Shells for the Shell Loading Revolvers work in which Shell Loading Revolvers? After all many of them look a lot alike so can you mix and match Shells for the various types of Shell Loading Revolvers?

In this Vimeo Instructional Video I test out a bunch of Shells to see which ones actually will work or not work in several of the most popular Shell Loading Revolvers.

Some of the Shell Loading Revovers Tested in this Instructional Video are:

• Dan Wesson Classic Revolver (BB, Airsoft, Pellet)

• Dan Wesson 715 Revolver (BB, Airsoft, Pellet)

• Colt Single Action Army Peacemaker (BB, Airsoft, Pellet)

• Gletcher NGT and NGT-R (BB and Pellet)

• Webley Mark VI (BB)

• KWC 357 / Umarex 357 (BB, Airsoft)

• G&G G731 (Airsoft) 

With the popularity of the KWC - Cybergun 1911 Blowback CO2 Pistols and how super realistic they are in so many ways, it is no surprise that people often ask me if they can replace the original grips with grips made for a real 1911.

The short answer is yes you can! You will have to be prepared to remove just a little bit of material from the backside of both grips near the bottom of the handle where there is an area that has been flared out to accommodate the CO2. Not really a big deal, you can use a Dremel for the quick and easy approach or even some sand paper if you don't mind taking a little more time.

In this Vimeo Video I demonstrate using grips that fit a real 1911 and show you just exactly where you will need modify them to fit on the KWC and Cybergun CO2 Blowback 1911 pistol series.

Buy the KWC Blowback CO2 1911 BB Pistol in Canada

Whether you like it or not, most of us have come across an Airgun with an ugly orange tip on it at some point. In most cases you will find the intrusive orange or red tips on Airsoft guns that shoot plastic BB's, in some cases you will even find them on Airguns that shoot either lead pellets and/or steel BB's.

It really comes down to where you live as to what your local gun laws have determined is required for your area. You may even live in a region where Airguns and Airsoft guns are not allowed at all! So for you a red or orange tip on the front would be welcome if it would allow you to own an Airgun or Airsoft gun. What about the entire gun being painted a bright color, well that is the case for some folks so again having a red or orange tips may not be as bad as it originally seemed...

In Canada where I live, we used to only be allowed Airsoft guns that had clear sections as our replica gun laws are very strict and all black Airsoft guns would have fallen iinto the "replica" category if they did not have large clear plastic see-through sections on them. This clear section law was revised somewhat over the last several years to allow for all black Airsoft guns here in Canada. It was determined that many Airsoft guns with higher fps limits could cause a serious injury to a human, making them less of a toy in the eyes of the law and more of a weapon. Because of this, Airsoft guns that are capable of shooting a .20 gram plastic BB at a velocity of 360 fps or "higher" are now considered to be similar in the eyes of the law to a regular steel BB or lead pellet shooting Airgun. In Canada, Pellet and Steel BB guns are actually considered firearms of a sort so this allows the higher fps Airsoft guns to be all black since it can not be a replica of a firearm if it is in fact considered to be a firearm by law.

The long and short of all of this is that here in Canada we do not require our Airsoft guns to have orange or red tips since they are considered more or less to be just like any other Airgun and our Airguns do not have red or orange tips either.

Getting back to the title of this article "No Orange Tip On Your Airsoft Gun! Are You Insane?" I often get folks from the US giving me heck for removing the orange tips from my Airsoft guns or asking me why my Airsoft guns don't have them in the first place. These people even state that I could get in a lot of trouble for this! Perhaps they think I live in the US or that US laws govern Canada as well? I am not sure but I can say for the record that I am not breaking any laws at least here in Canada where I live.

I know in the US that wholesalers and retailers by law have to sell Airsoft guns with the affixed orange tips on them, once the end user receives that gun and depending on which state they live in, it may or may not be legal to remove the orange tip. Again, you will need to look into your local state laws as they are different from state to state in the US.

If you have been watching my Full Auto Fun Videos, then you will have noticed that I have recently been using Clay Pigeons as my go-to targets. Generally Clay Pigeons are shot from launchers and used with shotguns since the flight of the Clay Pigeon simulates a bird in flight nicely.

So I thought, why not use them as reactive targets for my Airguns and Airsoft guns? It turns out they work pretty darn good, well at least with 4.5mm Steel BB pistols and I would imagine even better with pellet guns. What about Airsoft guns, will the Airsoft lighter weight plastic BB's have enough mass to get the job done?

You'll have to watch this video to find out the answer to that question when I unload a full magazine of .20 gram Airsoft BB's into some Clay Pigeons using my KWC .50 Desert Eagle...

Buy KWC Airsoft Desert Eagle in Canada

Buy KWC Silver Desert Eagle in Canada 

A very common occurrence with CO2 Airguns and Airsoft guns are leaky CO2 seals. Usually this occurs right where the CO2 cartridge connects to the main valve area. This can be either in the gun or in the magazine depending on the setup of the airgun.

There are many reasons why this can happen, but the most common reasons are a worn-out or dried up seals or even a seal that has been imprinted or misshapen from the constant pressure of the tip of the CO2 pressing against it.

When this happens you may encounter a leaking CO2, the severity of the leak can vary from mild slow leaks to leaks that can be so bad that the gun is unusable. Keep in mind there can be other problems not related to the CO2 seal such as in the valve area, the fix I show you in this YouTube video will not fix a leaking valve, you can try using something like Crosman Pellgun oil for a problem like that.

Watch my below Vimeo video where I show you how you can easily use some Plumbers Teflon Tape to improve the contact points between your CO2 and CO2 main seal and eliminate leaking CO2 in your Airgun.

A very common question I get asked is "How Long Can I Leave CO2 in My Airgun?" So what do I do when I get asked a question over and over again... Well I make a video and give you my answer to the question.

Some CO2 Related Questions I seem to get over and over again are:

1. Can I leave an unused CO2 in my Airgun and for how long is it safe?

2. Can I reuse a C2 once it is empty?

3. Can I use my gun without CO2?

In this YouTube video I address questions 1 and 2, I kind of forgot about question number 3 since it is not as often but it does come up from time to time believe it or not and the answer to being able to use a CO2 airgunwith out CO2 is "NO", It's kind of like trying to drive a car without gas, or turn on a light without electricity or stay alive without food...

So anyways, watch my below Vimeo video for answers to questions one and two: