In this "head to head to head" pistol shootout I compare three of my more powerful, or you could say effective air pistols against each other. Shooting at some pop cans from about 30 feet away to see how destructive each one is. I don't generally recommend air pistols for pest control simply because they tend to be less accurate and powerful than rifles, especially out at the longer ranges where a magnified scope is required and notably where the pesky vermin like to hang out.

I would have to say out of the three tested in this video comparison, the Webley Alecto in .22 caliber and the Modified Drozd Full Auto BB Gun would for sure get the job done at closer ranges. The Webley Alecto simply because it can hurl a heavy grain .22 caliber lead pellet right around the 500 fps mark which will take down small pests, again at close ranges.

My second choice or even first choice depending on how active the pest are would be my modified full auto 1200 rounds per minute Drozd that hurls 4.5mm Steel BB's at over 500 fps (under 4.2 foot pounds) at a rate of 20 BB's per second! A 4.5mm Steel BB traveling at 500 fps will penetrate fur and feathers very well and with most of the 20 BB's hitting a target in a matter of 1 second, that is going to humanly put a small to even medium sized pest down for sure. And yes the Drozd becomes a pistol when yuo take the rear stock off ;)

My last choice for the job is the Xisico XSP180 in .177 caliber since like the Webley Alecto it is only a single shot, so you got to make it count and being that it has less overall energy than the Webley Alecto again I would prefer the Alecto over the XSP180.

Watch my "head to head to head" Vimeo video to see how these three pellet pistols compare:

Another quick revisit of the KWC/Cybergun M92 Beretta - Taurus full metal, full blowback, CO2 4.5mm Steel BB pistol series. They come in several flavors but are all made by KWC and in many cases redistributed licensed by Cybergun. This Field Test Shooting Video Review focuses on the Cybergun Swiss Arms P92 version.

I have several videos I made for the Cybergun GSG 92 version showcasing an early on Table Top Review, Field Test Review and even a Full Auto Mod Video.

Now that I have a more standardized Field Test Shooting format, I though I would revisit this series of KWC/Cybergun Beretta - Taurus Replica BB Pistols and do a follow up Field Test to get some more camera angles and hopefully a nice tight target grouping using my standard semi rested position from 20 feet away.

I also incorporate some high speed video near the end of this Field Test Shooting video Review to go along with the Chronograph and target portion of the Filed Test Shooting review.

The KWC - Cybergun Full Blowback All metal serious of Replica CO2 BB Pistols has been hugely popular over here at Replica Airguns and for good reason, they are very realistic in looks and operation, are priced very respectably and replicate several of the more popular semi auto pistols.

Buy the Swiss Arms P92 in Canada  -  Buy the Swiss Arms P92 in the US

I wanted to show off a few new items that I will be reviewing, one being the Crosman MK-177 Pellet and BB pneumatic multi-pump air rifle that was very graciously provided to me by Crosman for review. And the other item is something kind of new in terms of the type of gun, since it is not really gun but rather a bow, or crossbow to be exact. We hope to be adding to our Replica Airguns Store a couple variations of the Avalanche Trailblazer 150lb Crossbows in wood stock and polymer stock versions.

Here are a couple key points about each item being looked at in this update video and then I will leave you with some detailed photos to drool over and of course my YouTube Update Video to watch...

Crosman MK-177 multi-pump bolt action .177 caliber BB/pellet air rifle:

• Shoots both .177 caliber pellets and 4.5mm Steel BB's

• Maximum 800 FPS (US Version being reviewed here)

• 5 shot pellet magazine and 300+ BB reservoir

• Multi-pump single shot bolt action

• 3-10 pumps per shot

• 16.75 inch rifled barrel

• 3.5 pounds

• Mostly plastic with some internal metal parts

Avalanche Trailblazer 150lb Crossbow with Wood Stock:

• 150 pound pull

• Fiberglass bow

• Wood Stock

• Comes with two arrows

• Fully adjustable rear sight

• Can mount a dovetail sight to it.

Buy Air Rifles in Canada  -  Buy Air Rifles in the US

• Checkout my Field Test Review for the Umarex Walther P99 CO2 Blowback Airsoft Pistol:

Type: Airsoft Pistol.

Manufacturer: Umarex.

Model: Walther P99 DAO

Materials: Metal & Polymer.

Weight: 1.5 pounds.

Barrel: 4 inches, metal non-rifled.

Propulsion: 12 gram CO2.

Action: Semi auto, double action only with blowback.

Ammunition Type: 6mm plastic Airsoft BB's.

Ammunition Capacity: 15 round stick magazine.

FPS: 380.

Trigger Pull: The Double Action Only trigger pull on the Umarex Walther P99 CO2 Blowback Airsoft Pistol is long but not overly heavy for a double action trigger, it does have a break point mid way where it locks partway back, I presume this is the point in which a BB is loaded from the magazine into the barrel? The rest of the pull is still medium but much shorter with a distinct release point.

Accuracy: I did do a quick preliminary test before I made this table top review to get an idea of where this gun performs in terms of FPS and accuracy, I shot 5 rounds through my Chronograph on a fresh CO2 and got an average of 333FPS which was a bit lower than the claimed 380 but it was not the hottest of days. I also stepped back 20 feet and from a semi rested position I was able to get 9 shots within 2 inches of each other which was not bad for a DAO gun that I have never shot before. I did shoot a bit down and to the left with the set sights.

Build Quality: The Umarex Walther P99 is well built for its rather low price tag, it may not have all the bells and whistles but it does get the job done with good fit and finish and materials used. You will find a plastic/polymer frame but there is a lot of metal where it would normally be found on the real steel version like in the slide, magazine, trigger, slide catch, magazine release, inner barrel and many other internal parts. No real complaints here!

Realism: The Umarex Walther P99 CO2 Blowback Airsoft Pistol is pretty close in looks to a real steel Walther P99 with the exception of a missing decocker, but I'm pretty sure this is the same with the real steel DAO version? There is also the funny looking safety on the right side of the frame found on many Umarex airguns. I have to mention the red tip but again this can be removed and even when removed the barrel it is still recessed which adds to the realism. The Blowback action, Walther licensing and nice heavy weight all add up to make this Airsoft pistol look and feel the part.

Purchase it from: The Replica Airguns Store

Pros:

• Low cost for a very believable and solid replica.

• All metal stick magazine.

• Metal slide and internal parts gives it decent weight.

• Rail for accessories.

• Well hidden CO2 screw.

• Walther licensing.

• Recessed inner barrel.

• White dot sights, easy to use.

• Right amount of power for indoor CQB style airsoft games.

Cons:

• Comes with a red tip even in Canada.

• Double action only, so trigger is a bit heavier.

• Kind of funny safety, not like the real gun.

• Blowback was a bit sluggish.

Comments:

Overall the Umarex Walther P99 CO2 Blowback Airsoft Pistol is a very good buy, it's a decent replica of the real steel Walther P99 with blowback operation, lots of metal parts, good fit and finish, decent performance and full Walther licensing and trademarks. All at a very affordable price tag. It may lack some of the extras you will find on more expensive and more functional Airsoft pistols but the simplicity of the Umarex Walther P99 CO2 Blowback Airsoft Pistol means it will most likely be a bit more reliable with less to go wrong down the road. If you have been looking for a nice Walther styled replica in an Airsoft version this may be just be the ticket!

My Vimeo Video Review for the Umarex Walther P99 CO2 Blowback Airsoft Pistol:

Buy the Umarex P99 CO2 Pistol in Canada 

Buy the Umarex P99 CO2 Pistol in the US

Here is a quick Update video of three Airsoft guns, two of which I have touched upon before but have not gotten around to doing any actual Table Top or Field Test Shooting videos for you (The ASG Dan Wesson Airsoft Revolver and the Umarex P99 Blowback Airsoft Pistol). I also show you a new Umarex Airsoft Gas Blowback PDW, the H&K MP7 A1, a very realistic version I am sure will be of interest to many of my Airsoft fans.

I will be doing proper Table Top and Field Test Videos for each of these Airsoft guns as soon as I can get to them all, starting with the Umarex Gas Blowback H&K MP7 A1 Airsoft PDW so stay posted for these upcoming video reviews...

Buy ASG Airsoft Pistols in Canada  -  Buy ASG Airsoft Pistols in the US

Buy this Airsoft Pistol in Canada  -  Buy this Airsoft Pistol in the US

Buy this Airsoft Machine Pistol in Canada  -  Buy this Airsoft Machine Pistol in the US

After many many requests to show how the Umarex Walther PPK CO2 Tab Modification is done I have relented to public demand. I don't actually cut my tab in this PPK CO2 Tab Modification Video but I do go step-by-step in detail and compare my modified Umarex PPK to my unmodified Umarex PPK. It is really very basic on how this is done and only a hack say and perhaps a file are all that is required to make the modifications to the PPK CO2 tab in order to make it flush with the bottom of the handle area.

Your best bet is to simply watch my YouTube Video located below and follow the steps there but here it is in text form:

1. Place an empty (already pierced) CO2 into your Umarex Walther PPK and tighten the unmodified CO2 tab until fully tightened, just like you would tighten a fresh CO2.

2. Take note at how many threads are exposed between the bottom of the handle and the top of the plastic CO2 tab, there should be about 2-4 threads exposed.

3. Unscrew the CO2 tab all the way, place the PPK BB Pistol so it is secure (in a vice of some sort) and use a hacksaw or dremel to shorten the CO2 screw just above the plastic tab at the thread location you previously noted. Be conservative as you can always cut or file the screw a bit shorter if your first cut was not short enough.

4. Now use the same hacksaw or dremel to cut a notch in the exposed cut area of the CO2 screw so that you can use a slot screwdriver to tighten the CO2 screw.

5. That's it - Enjoy your modified Umarex Walther PPK CO2 BB Pistol!

Watch my Vimeo Video of the Umarex Walther PPK CO2 Tab Modification Tutorial:

Buy the PPK/S in Canada   -   Buy the PPK/S in the US

This is not meant to be a full review of either the BB or Airsoft version of the Cybergun - KWC CO2 Blowback Mini UZI's but I do talk about specifications, show you around both guns, and put them both through a full Field Test so I guess in a way, perhaps it can be considered to be a full review ;)

I will list the specifications here for you but I am not going to get into details like Trigger Pull, Build Quality, Accuracy and Realism. You can check out my other video reviews for more information on the Mini UZI:

• Cybergun 4.5mm CO2 Blowback Mini UZI Review

• Cybergun - KWC Mini UZI 4.5mm BB Gun Full Auto Modification

• Cybergun Mini UZI CO2 4.5mm BB Gun Chronograph and Full Auto Shooting Test

• Dual Full Auto BB Machine Gun Destruction

Type: CO2 Blowback Machine gun.

Manufacturer: Cybergun - KWC.

Model:Mini UZU.

Materials: Metal and Polymer.

Weight: 4.8 pounds.

Barrel: Metal, non-rifled.

Propulsion: CO2 x1.

Action: BB Semi auto only - Airsoft selectable semi & full auto, single action only.

Ammunition Type: 4.5mm Steel BB - 6mm Plastic Airsoft

Ammunition Capacity: 25 - 38 rounds

FPS: 350 - 400

As I said you can check out all my other videos for info on these very accurate Mini UZI Replicas, I mainly want to go over some of the main differences and similarities for both the BB and Airsoft versions.

In terms of build quality they are made almost exactly the same and weigh in at a hefty near 5 pounds, the only differences are the inner barrel and magazines to accommodate the different sized ammo. The BB version has a 25 round single stack magazine that does not have a follower to stop the bolt from continuing to operate even after the magazine is empty. While the 6mm Airsoft version has a double stack magazine that holds 38 rounds and does have a follower to stop the bolt which can save you some unintentional wasted CO2.

The Airsoft Mini UZI version is distributed by KWC while the 4.5mm BB version is distributed by Cybergun, you will find the UZI and IWI licensing on the Cybergun 4.5mm BB version but not on the KWC 6mm Airsoft version.

Out of the box the KWC Airsoft Mini UZI is ready to go in both semi auto and full auto while the 4.5mm steel BB version will only shoot in semi auto mode, it can however be easily modded to shoot in full auto.

Both guns come in cardboard boxes with manuals, some BB's and an Allen key to tighten the CO2. The KWC Airsoft Mini UZI also comes with a handy speed loader.

There is a slight fps velocity difference between the two with the KWC Airsoft 6mm plastic rounds traveling at around 400 fps (with .20 gram BB's) and the 4.5mm Steel BB's traveling at right around 350 fps. In the field test portion I test both guns out on some water filled cans to see how each ammo type performs in terms of penetration.

Your best bet is to watch both my Table Top and Field Test Comparison Video Reviews and see for yourself how they compare!

Buy BB Mini UZI in Canada   -   Buy BB Mini UZI in the US

Buy Airsoft Mini UZI in Canada   -   Buy Airsoft Pistols in the US

• Also Checkout my Field Test Shooting Review for the Cybergun Sig Sauer P226.

Type: 6mm Plastic BB Airsoft Pistols.

Manufacturer:Cybergun

Model:Sig Sauer P226

Materials: Metal slide & frame.

Weight: 2 pounds (920 grams).

Barrel: Metalnon-rifled smooth bore.

Propulsion: Gas Blowback (GBB).

Action: Single and double action.

Ammunition Type: 6mm plastic Airsoft BB's.

Ammunition Capacity: 26 rounds.

FPS: 383 fps (Using .12 gram BB's).

Trigger Pull: The trigger pull on the Cybergun Sig Sauer P226 Airsoft Replica is good in both single and double action. Once the slide is pulled back and released the first round is chambered and the hammer will remain back placing the P226 in single action mode, the pull is light and the take-up is fairly short, most of your shots will be in single action mode unless you use the de-cocker to lower the hammer for a subsequent double action next shot, double action shots are still pretty light but much longer in order to cock the hammer.

Accuracy: Shooting the Cybergun Sig P226 from 20 feet out in semi rested position I was able to get very good results. I placed 10 rounds in about 1.5 inches with the shot placement being a bit low possibly due to my barrel mod, adjusting the hop-up may bring the aim point back up to where it should be. The Sig Sauer P226 Airsoft Replica shot right around the 316 fps range while conducting my 5 shot average chrony testing which was lower than advertised but I was using much heavier .20 gram BB's. You can expect to get a full magazine worth of shots out of each gas fill-up but I did notice that as the magazine got colder it did tend to become much less efficient and also seemed to vent a lot of vapor.

Build Quality: The build quality is generally good and I was surprised at the finish on this model as the paint is not showing any wear marks so far, the fit is good with minimal slide and barrel wobble and everything is working very well with no problems so far with a fair amount of shots through it, guess you could say I like shooting this gun :) Most of the gun is metal with only the grips and a couple internal parts being plastic.

Realism: The Cybergun Sig Sauer P226 6mm Airsoft pistol is a replica of the real steel Sig Sauer P226 right down to the licensing and it really is a great looking and functioning Airsoft Replica. You can field strip this gun exactly like a real Sig and all the mechanical parts work just the same including a working de-cocker and adjustable front sight.

Available in the:Replica Airguns Store

Pros:

• All metal pistol with good overall realistic weight to it.

• Very crisp and firm full blowback operation.

• Excellent fit and finish - paint seems to be wearing well.

• Nice accurate looking and working Sig Sauer P226 Replica with licensing

• Working de-cocker.

• White dot sights for quick target acquisition.

• Front sight is adjustable for windage.

• Full size drop out magazine holds BB's and gas.

• Fully field strip-able.

Buy this Airsoft Pistol in Canada  -  Buy this Airsoft Pistol in the US

Cons:

• Comes with an orange tip not required for Canada.

• Seemed to shoot a bit low for me, could adjust with hop-up a bit?

• Only one magazine per Gas fill.

Comments:

I am a big Sig Sauer fan so it would take a lot for me to not give this gun a good review, with that said it performed pretty well, sure it was not the most powerful but I was using gas over CO2 so I was not expecting too much, it also shot a bit low for me but again that may have been because of the barrel mod so who really knows for sure at this point ;) And yes it came with that unsightly orange tip that I took short work of removing. At teh end of the day I still love it and it performed well without letting me down, just like a would expect from a real Sig Sauer!

My Vimeo Table Top  Review of the Cybergun Sig Sauer P226 GBB Blowback Airsoft Pistol:

Buy this Airsoft Pistol in Canada  -  Buy this Airsoft Pistol in the US

• Also Checkout my Table Top Review for the Cybergun Sig Sauer P226.

I usually do my Table Top Video Review first but this time around I did my Field Test Video Review first since I was all setup checking out a couple other guns at the time. When I do my detailed Table Top Video Review for the Cybgergun Sig Suer P226, I'll post the link here so stay tuned. If you have not already checked out my Barrel Mod Video for this same gun then check that video out where I remover the extended orange portion of the metal barrel and make the barrel flush with the end of the slide which is how the real steel version was originally made.

Getting back to the Cybergun Sig Sauer P226 GBB blowback Airsoft Pistol field test, as per usual I test this Airsoft semi auto gas blowback pistol on the Chronograph to see what kind of real world velocity I get and since I had some Green Gas on hand, I used it for this part of the review and got an average of 315 fps with a six shot string.

I also stepped back 20 feet and shot 10 times at my stationary target using a semi rested position (sand bag up front and kneeling in the back). Even though the Sig Sauer P226 shot a bit low I did get about a 1.25 inch group with the exception of one flyer that hooked down just a bit making the 10 shot group a bit wider at just under 2 inches. The low shot placement may have been caused by my barrel mod but since I did not do a before and after test, I can not say for sure?

Make sure to watch my YouTube Video of this Field Test as it also includes some nice slow-motion of the slide blowback at both 400 and 1200 frames per second.

Watch my full Video Field Test Shooting Vimeo Video below:

Buy this Airsoft Pistol in Canada  -  Buy this Airsoft Pistol in the US

I have not done my official Table Top and Shooting Reviews for the Gas Blowback Airsoft Cybergun Sig Sauer P226 but I really wanted to cut off the ugly orange painted barrel tip, it was kind of driving me crazy! keep in mind here in Canada we are not required to have orange tips on our Airsoft guns, most of the all metal or all black Airsoft guns imported these days fall into the "airgun uncontrolled firearms" category. If you live in the US or other parts of the world you could be breaking the law if you do this mod so be warned...

Your best best is to simply watch my Vimeo Video as I show you exactly how I removed the orange painted portion of the metal barrel using a hack saw, file, vice and some sand paper. All in all it was not too difficult and only took about 15 minutes to complete...

Buy this Airsoft Pistol in Canada  -  Buy this Airsoft Pistol in the US

I already posted that I recently hit 10,000,00 YouTube video Views but I have been hinting about there being another Giveaway/Contest. After much thought I wanted to have a way that more than just one person could benefit from this. So I decided to list a bunch of my Canada Store products on sale. (Sorry US customers but I have a lot more restrictions in the US when it comes to what I can do with my pricing).

These Canadian sales will be in effect from now until October 10th and to make things even better, one lucky shopper during this time will get their entire order for free (This includes US Customers too).

So make sure to get in on the savings and the chance to get your order free!

In this "Update Video" I also show off some new previously owned guns added to my collection, an Airsoft ASG shell ejecting CZ 75, a no-name KSC Airsoft shooter and a Gamo Combat .177 caliber pellet revolver. And if you're into spring piston break barrel pistols, make sure to watch for my customized Exisco XSP180 .177 caliber Verminator!

Ten Million Video Views Giveaway Plus CZ 75 - Glock Airsoft - Gamo Combat Pellet Revolver

Here is a sample of some of the items on sale right now...

Buy King Arms M4A1 in Canada 

Buy King Arms M4A1 in the US

Buy Webley Alecto in Canada

Buy Webley Alecto in the US

Buy EKOL ES55 in Canada

Buy EKOL ES55 in the US

Check out all items on Sale Now!

When it comes to Airguns and Blank Guns, it's not often that an item is actually more money to buy in the US but with the Webley Alecto, it was actually more money in the US so I got to thinking, why not ship our Canada version to our US customers so they can save a few bucks! Both the US and Canada Webley Alecto are the same with only one exception, the Canada version has been detuned but this can be easily rectified with a simple valve modification (Instructions delivered after purchased from Replica Airguns).

Of course you can still buy the Alecto here in Canada at the already low Canadian price.

Buy Webley Alecto in Canada   -   Buy Webley Alecto in the US

Click here to check out my Field Test for the Baikal Drozd Blackbird

Type: BB Machine gun.

Manufacturer:Baikal.

Model:Blackbird IZH MP-661K.

Materials: Metal & Polymer.

Weight: 4 pounds.

Barrel: 8 inches, metal-rifled.

Propulsion: CO2 or (Bulk air with adaptor).

Action: Electronic trigger with 1-3-6 round burst & 300-340-600 Rounds Per Minute.

Ammunition Type: 4.5mm steel BB's.

Ammunition Capacity: 900 rounds.

FPS: 360-500.

Trigger Pull: The trigger pull on the IZH Drozd Blackbird is nice and light due to the fact that the trigger is not mechanical but is instead an electronic on-off switch that operates a solenoid. The solenoid pulsates in turn hitting the CO2 valve release. This is how the single fire and burst fire rates are achieved, by means of electronics.

Accuracy: The Drozd Blackbird is designed to be a machine gun and so testing it in single shot mode for accuracy is kind of taking it out of its element. Even so it did reasonably well, but when when I flicked it over to full auto it actually seemed to tighten up and start grouping even more centered and closer together considering the vast amount of rounds coming out of the barrel all at once :)

Build Quality: This is a typical Russian made gun, all business and less importance put on looks but even so it is visually appealing, at least to me! Everything works exactly as it should and even though the main shell is made out of plastic, it's really more of a weapons grade polymer so there is no cause for concern here. There are a fair amount of metal components like the factory barrel, much of the magazine and many internal parts. This air gun is very durable!

Realism: The Baikal Drozd Blackbird IZH MP-661K is not a replica, but it does look like a sub machine gun of sorts, I'm really just not sure exactly what it looks like as it kind of has its own look. When you start shooting it, looks just don't seem to matter anymore, all you can think about is how much damage is happening down range.

Purchased From: The Replica Airguns Store.

Pros:

• Very well made BB machine gun.

• Excellent power.

• Good accuracy in all shooting modes.

• Uses the 12 gram and 88 gram CO2 (Can also convert to bulk air)

• Stock version can shoot up to 600 rounds per minute.

• Rifled barrel.

• Adjustable rear sight for windage and elevation.

• Improved rail sits higher and is longer then the classic Drozd.

• Drastically Improved magazine capacity (motor hopper system)

• Many mods available for this gun.

• Great for pest control, especially the ones that are on the move.

• 10 out of 10 on the fun factor.

• Made in Russia.

<!-- google_ad_client = "ca-pub-9036472715040282"; /* Replica Airguns Content */ google_ad_slot = "1487049688"; google_ad_width = 468; google_ad_height = 15; //-->

Cons:

• BB Hopper motor sound is a bit annoying!

• A bit more accuracy in semi auto mode would have been nice.

• On the pricey side.

Comments:

The Baikal Drozd Blackbird IZH MP-661K takes all the fun you get with the Classic Drozd and gives you even more fun. It may be one of the more pricy BB machine guns on the market but it is well worth the extra cost to get such a quality product that not only is great out of the box but can also be modified in so many ways to improve its performance and looks dramatically. If you are looking for the absolute top player in the BB Machine gun category then the Drozd Blackbird is the top contender with its excellent build quality and performance along with the nearly unlimited modifications available to make the Blackbird perform up to anyones standards.

My Vimeo Video Review for this Russian made Blackbird BB Machine gun:

Buy this gun in Canada   -   Buy this gun in the US

Click here to check out my Table Top Review for the Baikal Drozd Blackbird

I'm kind of doing this one backwards this time around. I was going to do the table top review of the Baikal Drozd Blackbird first but the weather was just too nice to pass up today to not get outside and give this gun a thorough testing.

I will be posting the table top review in a few days with all the specification (Here it is now) but if you're looking for some basic info on the Blackbird you can checkout our online store where you can find some statistics on the Drozd Blackbird and you can also checkout my Drozd Classic Review where I do a short comparison between the Drozd Classic and the newer updated Blackbird version.

I had a lot of fun shooting this gun, it lays down a lot of steel in a very short amount of time and has a virtually endless 900 round BB hopper that just keeps on going. During my testing I shot close to 400 rounds or more using one 88 gram CO2 cartridge and even near the end the Baikal Drozd Blackbird had pretty good feet per second performance.

My Baikal Blackbird does have some upgrades: (JimC Barrel, Full Auto-High RPM Mod Chip, Added Accessory Rails, Red Dot Scope, Tactical Light, Laser and Bulk Air kit) but the stock version is "almost" as fun :)

Enjoy this Vimeo video, it was crazy fun to make!

Buy this gun in Canada   -   Buy this gun in the US

Thought I would share this photo of a Magazine doubler for his Umarex MP5K PDW one of my viewers (Daniel) sent to me. He lives in the UK and bought his from a supplier out his way. I don't sell them sorry but I have included an Amazon link for my US viewers.

Sometimes you just got to make a video because you can and because it's just plain old fun! And that's why I made this video of me shooting some cans with dual full auto BB machine guns. One is my full auto converted and trusted Cybergun Mini UZI and the other is my newly acquired ZMZ Tyrex PPA-K-01 Russian Machine Pistol.

So sit back and enjoy, I know I did :)

Buy this gun in Canada   -   Buy this gun in the US

One of my viewers sent some photos of his custom sanded and polished two-tone ASG STI Duty One 1911. Ken did an awesome job and it makes me want to do the same to mine :)

He started out by sanding off the paint with 500 grit sandpaper and working his way finer right up to 2000 grit and then finishing off with some Meguiar’s NXT Generation metal polish. The results are amazing -  see for yourself!

Buy this gun in Canada 

Buy this gun in the US

Type: BB Machine gun.

Manufacturer:Baikal.

Model:IZH MP-661K.

Materials: Metal & Polymer.

Weight: 3.5 pounds.

Barrel: 8 inches, metal-rifled.

Propulsion: CO2 or (Bulk air with adaptor).

Action: Electronic trigger with 1-3-6 round burst & 300-340-600 Rounds Per Minute.

Ammunition Type: 4.5mm steel BB's.

Ammunition Capacity: 30 rounds.

FPS: 360-500.

Trigger Pull: The trigger pull on the IZH Drozd is nice and light due to the fact that the trigger is not mechanical but is instead an electronic on-off switch that operates a solenoid. The solenoid pulsates in turn hitting the CO2 valve release. This is how the single fire and burst fire rates are achieved.

Accuracy: When I was sighting the Baikal Drozd in I got several 5 shot groups well within 1 inch 30 feet out from the target. But when I did my actual video accuracy test, the Drozd did not perform as well, getting more like a 2 inch group, still very reasonable for a gun that can shoot 600 rounds per minute out of the box and 1200 rounds per minute when modified. With metal streaming out the barrel like that you are pretty much going to hit what ever you point it at, the odds are in your favor!

Build Quality: This is a typical Russian made gun, all business and less importance put on looks but even so it is visually appealing, at least to me! Everything works exactly as it should and even though the main shell is plastic it is really a weapons grade polymer so there is no cause for concern here. There are a fair amount of metal components like the factory barrel, most of the magazine and many internal parts.

Realism: Again, the Baikal Drozd IZH MP-661K is not a replica, but it does look like a sub machine gun in many ways, I'm really just not sure exactly what it looks like but when you are shooting this gun you really don't think much about this point because you are too busy grinning!

Purchased From: The Replica Airguns Store.

Pros:

• Very well made BB machine gun.

• Excellent power.

• Good accuracy in all shooting modes.

• Uses the 12 gram CO2 - a bit cheaper! (Can also convert to bulk air)

• Stock version can shoot up to 600 rounds per minute.

• Multiple stock lengths.

• Rifled barrel.

• Adjustable rear sight for windage and elevation.

• Removable magazine hold BB's and CO2.

• Many mods for this gun.

• Great for pest control, especially the ones that don't stay still.

• Made in Russia.

<!-- google_ad_client = "ca-pub-9036472715040282"; /* Replica Airguns Content */ google_ad_slot = "1487049688"; google_ad_width = 468; google_ad_height = 15; //-->

Cons:

• 12 Gram CO2 - you need to change it often!

• Top Accessory rail is a bit short and low.

• Rear stock can get lose sometimes (just add some tape to tighten it up a bit).

Comments:

The Baikal IZH MP-661K is one of the most fun BB machine guns out there and well worth the extra cost to get such a quality product that not only is great out of the box but can also be modified in so many ways to improve it's performance and looks dramatically. Sure the Baikal IZH MP-661K now has a big brother, the Drozd Blackbird, but the Blackbird may be just a bit of overkill for some, I kind of like the Drozd Classics more compact size and if you can't nail what your shooting at with 30 rounds then your doing something very wrong! The Drozd is really the epitome of extreme BB gun weaponry!

My Vimeo Video Review for this Russian made BB Machine gun:

Buy BB Rifles in Canada

Buy BB Rifles in the US

Mil3 sent me some more updated photos of his customized Cybergun Tanfoglio Witness 1911 now with the Sight Rail add on.

Buy this gun in Canada   -   Buy this gun in the US

The Webley Alecto (AKA: Zoraki HP-01) may not fit in exactly as a "Replica" Airgun, although it does resemble a bloated Dessert Eagle! But it is an Airgun worthy of spending some time reviewing an this is now my third Vimeo Video review for the Webley Alecto. My first Video Review was a Table Top Review where I covered most of the Webley's basic operation. My second Vimeo Video was a Chronograph Test to see what my Webley Alecto could do performance wise for FPS.

<!-- google_ad_client = "ca-pub-9036472715040282"; /* Replica Airguns Content */ google_ad_slot = "1487049688"; google_ad_width = 468; google_ad_height = 15; //-->

I really wanted to do a video of this gun just shooting because that's what it does best, put lead down range very accurately! So I setup three cameras to capture it all from just about every angle I could think of and I set up 30 feet away from my target and shot 5 rounds in a rested position using a Red Dot Scope. The results where not surprising - pretty close to a 1/2 inch grouping!

If you're looking for a compact, hard hitting, accurate target or small pest control Air gun then look no further, the Webley Alecto has the goods!

Watch the full Multi-angle Vimeo Video of my Webley Alecto Shooting Test:

Buy this gun in Canada

Buy this gun in the US