Full Auto Fun video number three this week and this one is perhaps the craziest one! When you take a Drozd Blackbird that already has a 800-1000 round BB magazine, convert it to 1200 rounds of full auto, add a custom JimC Barrel to it, some bulk CO2 and a bunch of other cosmetic accessories... Well you get the most ridiculous full auto BB gun you can ask for.
Since I had an extra 800-900 BB's more than I am used to when making these full auto videos, I decided to add a few additional targets over and above the clay pigeons I have been using so far. I picked up a nice fairly heavy gauge Santa tin and a rather solid hard wax candle from the dollar store that proved to add some drama to this Full Auto Fun video!
Make sure to also watch my first two Full Auto Fun videos:
If you like what you see in this video and want an absolutely crazy BB gun, then checkout our Replica Airguns Store where we Sell the Drozd BB gun and some add ons for it!
This "Full Auto Fun" video focuses on my KWC/Cybergun 4.5mm Steel BB CO2 Blowback Mini UZI BB Gun, where I kick of a short series based around shooting a bunch of 4.5mm Steel BB machine guns! Sounds like fun cause it is fun!
This KWC/Cybergun Blowback Mini UZI comes in a variety of versions, 4.5mm Steel BB and Airsoft versions, it also comes in RWS and KWC Distributed models.
In this video I basically shoot a bunch of clay pigeons positioned in various locations and film it using 4 different camera angles to spice things up a bit.
I also mention some upcoming videos where I will be shooting my RAP4 MP5 and Baikal Drozd Blackbird Full Auto BB guns so make sure to watch those video when I upload them later on this week!
In this "head to head to head" pistol shootout I compare three of my more powerful, or you could say effective air pistols against each other. Shooting at some pop cans from about 30 feet away to see how destructive each one is. I don't generally recommend air pistols for pest control simply because they tend to be less accurate and powerful than rifles, especially out at the longer ranges where a magnified scope is required and notably where the pesky vermin like to hang out.
I would have to say out of the three tested in this video comparison, the Webley Alecto in .22 caliber and the Modified Drozd Full Auto BB Gun would for sure get the job done at closer ranges. The Webley Alecto simply because it can hurl a heavy grain .22 caliber lead pellet right around the 500 fps mark which will take down small pests, again at close ranges.
My second choice or even first choice depending on how active the pest are would be my modified full auto 1200 rounds per minute Drozd that hurls 4.5mm Steel BB's at over 500 fps (under 4.2 foot pounds) at a rate of 20 BB's per second! A 4.5mm Steel BB traveling at 500 fps will penetrate fur and feathers very well and with most of the 20 BB's hitting a target in a matter of 1 second, that is going to humanly put a small to even medium sized pest down for sure. And yes the Drozd becomes a pistol when yuo take the rear stock off ;)
My last choice for the job is the Xisico XSP180 in .177 caliber since like the Webley Alecto it is only a single shot, so you got to make it count and being that it has less overall energy than the Webley Alecto again I would prefer the Alecto over the XSP180.
Watch my "head to head to head" Vimeo video to see how these three pellet pistols compare:
Two of our most popular single shot target/hunting pellet shooters are back in stock again after what has been a rather long delay. The truth of the matter is we just didn't have a supplier for them anymore here in Canada until now. Webley as a company has been through some pretty big changes over the past several years and now hopefully it has all been worked out and supply will be steady.
Don't worry about the quality, that is still top notch! We now have the Turkish made Webley Alecto and Webley Tempest (both available in .177 and .22 caliber pellets) back in stock and I am happy to say the Alecto has even been improved with an upgraded Air Reservoir and even higher fps than before which means the Webley Alecto and the Webley Tempest now shoot right up to our maximum fps here in Canada before becoming restricted firearms so no need for an R-PAL which means happy shooting in places other than a gun range!
I would even rcomend both these Webley pistols for small pest control especially in the .22 caliber versions as they have the power and accuracy to get the job done.
In this Comparison Video I go through the benefits and shortcomings of CO2, Spring Piston and Pump Airguns. I focus mainly on Airguns but there is a bit of a crossover with Airsoft guns.
All three systems (CO2, Spring, Pump) create pressure that forces the ammunition with a high force out of the barrel. Similar to how gun powder is the source of energy for a bullet.
Here are some basic statements that best describe CO2, Spring Piston and Pump Airguns.
CO2 Airguns:
CO2 Airguns use the expansion of CO2 gas to create the pressure required for the ammo.
CO2 Airguns generally store enough CO2 for multiple shots per cartridge.
CO2 Airguns have a limit as to how much power they can produce since CO2 has a set vapor pressure of 850 psi, or about 56 bar at room temperature which is around 25 C or 77 F. CO2 Gas also requires a warm environment to expand so warmer temperature and longer barrels help with power.
Some CO2 guns can also use pressurized air tanks in place of CO2.
Spring Piston Airguns:
Spring Airguns use the release of a pre-cocked spring and plunger system to compress air to power the ammo.
Spring Piston Airguns require the cocking of the spring between each shot so they are single shot only.
Spring Airguns are limited to how much effort is humanly possible to cock the spring into position. If you make the spring to strong then not everyone will be able to use the Airgun effectively. Too week of a spring and the Airgun will lack power.
Spring Piston Airguns are known for having a fair amount of recoil and vibration when the spring moves both forward and backwards quickly inside the Airgun.
Spring Airguns can use either a mechanical spring or a gas spring.
Pump Airguns:
Pump Airguns (either Single or Multi-Pump) store air pressure in a chamber that when released, powers the ammo.
Most Pump Airguns require at least 1 or more pumps, often up to 10 pumps for each shot and you generally only get one shot per set of pumps. Not to be confused with PCP Airguns (Pre Charged Pneumatic) which have large pressure tanks that are recharged with a high volume of pressurized air that is capable of shooting multiple shots per charge.
Pump Airguns are also somewhat limited to how much effort is humanly possible since the higher the chamber pressure, the harder it will be to pump the Airgun.
Misc Airguns:
Generally speaking both Spring and Multi-Pump Airguns have more potential power than a CO2 guns since CO2 has a set peek pressure limit.
Pump and CO2 Airguns are know to have very little recoil since the pressure is stored in a chamber and then released by a valve. No slapping back and forth of a large internal spring.
Pros:
CO2 Airguns:
CO2 Airguns allow for multiple shots per CO2 cartridge for more realistic action shooting.
CO2 Airguns do not require any human effort to charge the gun other than loading the CO2 and Ammo into the Airgun.
CO2 Airguns allow for true semi auto shooting ability.
Spring Piston Airguns:
Spring Airguns have the potential for high velocity since the larger and stiffer the spring, the greater the output force.
Spring Airguns do not require anything other than your ammunition, typically either a Pellet or BB.
Spring Airguns are mechanically very simple which makes them very reliable and less expensive to produce than other types of Airguns.
Pump Airguns:
Pump Airguns have the potential for high velocity since more pumps equals greater output force, only limited by the users strength and the pressure rating of the Airgun.
Pump Airguns do not require anything other than your ammunition, typically either a Pellet or BB.
Pump Airguns have next to no recoil which makes them very easy to shoot and highly accurate.
Cons:
CO2 Airguns:
CO2 Airguns require the purchase and use of CO2 or they simple do not work.
CO2 Airguns are very susceptible to temperature changes, especially cold temperature since CO2 needs a warm environment in order to expand. Cool down effect also plays a role in power output.
CO2 Airguns have a maximum set amount of power output.
Spring Piston Airguns:
Spring Airguns require the pre-cocking of the spring for each shot.
Spring Airguns can take some getting used to since the spring recoil/vibration requires a very lose grip (Military Grip) to shoot accurately with them.
Spring Airguns should not be stored pre-cocked since this can damage the spring, less so with gas spring versions.
Pump Airguns:
Pump Airguns require pre-pumping to pressurize the air chamber for each shot.
Pump Airguns, especially Multi-Pump Airguns take the most amount of human effort for each shot.
Pump Airguns need to stored with at least one pump in them or the seals can get damaged over time.
I finally answer the question... Which Airgun is the Best? There has to be a best airgun out there right? So let's cut to the chase and stop waisting everyones time and money buying the third Best Airgun or even the second best Airgun! Why would you even want anything other than the very best Airgun available to mankind!
I really hope you weren't one of the gullible ones that actually bought something other than the Best Airgun, well I guess you're going to have to watch my YouTube video to find out which Airgun is the Best Airgun of all time...
So it's 2014 but I still needed to make my 2013 Airgun, Airsoft Gun and Blank Gun Collection Favorites for 2013. It's become a tradition I guess you could say. No I do not show all the guns in my collection but I do cover most of my favorites and also some new guns I picked up in 2013.
Here's a peek but make sure to watch the YouTube video bellow where I go over all my top picks for 2013. You can also buy many of the guns I show in this YouTube video over in our Canada and US Replica Airguns Store!
Another quick revisit of the KWC/Cybergun M92 Beretta - Taurus full metal, full blowback, CO2 4.5mm Steel BB pistol series. They come in several flavors but are all made by KWC and in many cases redistributed licensed by Cybergun. This Field Test Shooting Video Review focuses on the Cybergun Swiss Arms P92 version.
Now that I have a more standardized Field Test Shooting format, I though I would revisit this series of KWC/Cybergun Beretta - Taurus Replica BB Pistols and do a follow up Field Test to get some more camera angles and hopefully a nice tight target grouping using my standard semi rested position from 20 feet away.
I also incorporate some high speed video near the end of this Field Test Shooting video Review to go along with the Chronograph and target portion of the Filed Test Shooting review.
The KWC - Cybergun Full Blowback All metal serious of Replica CO2 BB Pistols has been hugely popular over here at Replica Airguns and for good reason, they are very realistic in looks and operation, are priced very respectably and replicate several of the more popular semi auto pistols.
FPS: 750 with Pellets and 800 with BB's for the US version (Up to 495 with Canada version).
Trigger Pull: The trigger pull on the Crosman MK-177 is medium length and fairly light. The trigger mainly releases the bolt so no pre-cocking of the trigger is required. The trigger is plastic but seems to work just fine as there is no real load on the trigger when shooting, you do need to get used to where the release point since there is some take up well before the trigger releases.
Accuracy: I found the Crosman MK-177 Air Rifle to be a very good shooter, getting about a 1 inch 10 shot grouping from 30 feet out in a semi rested position (sand bag up front, standing in the back). I also put 3 rounds through my somewhat failing Chrony Chronograph using 3,5 & 10 pumps and the MK-177 with the maximum 10 pump shot as high as 631 fps using 6.9 grain RWS lead pellets. I would expect the Canadian detuned version to shoot well below the 500 fps Canada limit much like my Canadian Crosman M4-177 I reviewed a while back.
Build Quality: The Crosman MK-177 Multi-pump Air Rifle is mostly molded plastic, but for a $100-ish Military Styled Replica Air Rifle it hits the mark in terms of affordability and if it was an all metal airgun you would more than likely expect to double or tripple this price point! Even though plastic is used throughout this Air Rifle, there are some internal metal parts where they need to be, the fit and finish seems to be good and I do not get the feeling the Crosman MK-177 is cheaply made in any way. The fact that most parts are molded means there is very little that can snap or break off and will make this air rifle even more durable longterm.
Realism: The Crosman MK-177 is a lose replica or copy of an FN SCAR Assault Rifle or ACR. It is not exact in terms of true dimensions to accommodate the pumping mechanism, You will not find very many working parts as just about everything is molded into the plastic on this Crosman MK-177 rifle. Unlike the Crosman M4-177 the lower magazine area is not removable and the rear stock is also none adjustable, I am not sure why Crosman didn't add these features to the MK-177 like they did to the M4-177? I am glad to see another Replica Assault rifle on the market as so few of them are available in Pellet or steel BB shooters.
None red dot version comes with detachable and adjustable iron sights.
Rails on top and sides for accessories.
Option of shooting pellets or BB's, I would stick to pellets and save the barrel since it is not semi auto.
Feels super solid since there are very few moving parts that could break.
Looks like the Crosman M4-177 Pellet magazines are compatible.
Cons:
Mostly plastic and just about everything is molded into the gun.
Bolt and magazine are on opposite sides?
Would of been cool if Crosman made a dedicated BB magazine?
Comments:
The Crosman MK-177 Multi-Pump Pellet/BB Air Rifle is very much like it's brother the Crosman M4-177 with a few plusses and a few minuses when comparing the two of them together. On the plus side the MK-177 has a bit more power and also the pumping is much easier while yielding higher internal pressures. On the downside the Crosman MK-177 is almost entirely molded plastic with no removable lower magazine or adjustable stock, and the bolt has been switched around to what I feel is the wrong side since now you need to index the magazine on one side and work the bolt on the other requiring a less efficient approach. Either way it is nice to have another replica air rifle on the marker and for the relatively low price you get a nice accurate pellet rifle, great for target shooting and even small pest control.
Watch my Vimeo Full Video Review of the Crosman MK-177 Pellet/BB Air Rifle:
I wanted to cover some basic Airgun, Airsoft Gun, Blank Gun and Paintball Gun information on what do they all shoot, what makes them shoot and some other miscellaneous info thrown in along the way...
Your should also watch the video attached at the bottom of this post as it goes into a fair amount of detail.
Let's begin with the types of ammo used:
Airgun Ammo
Airgun ammo for the most part is broken down into BBs and Pellets, the most standard size BB and Pellet is the 4.5mm or .177 caliber Steel BB and Lead Pellet. You can also get Pellets in other calibers and even other materials other than lead such as steel or aluminum, some can have plastic skirting around a metal interior.
Pellets also come in a variety of caliber's like .177, .20. 22. 25 and even larger but then I would start considering them to be bullets as they will take on the shape of a bullet when they get into the larger sizes.
Airgun Ammo is not be fired at people, it is primarily used for target and hunting small game.
Airguns can use Spring Pistons, CO2, Compressed Air and Multi-pump propulsion systems.
Airsoft Gun Ammo
Airsoft Guns for the most part shoot round 6mm (.22 caliber) plastic BBs which come in a variety of weights ranging from .12 grams up to .48 grams. There are larger Airsoft BBs such as 8mm and even larger.
There are biodegradable and even tracer florescent Airsoft BBs available.
Airsoft Ammo is traditionally used for Airsoft battles and can be fired at people using protective gear. Airsoft Ammo can also be used for target shooting.
Airsoft Guns can use Spring Pistons, Spring Piston - AEG (Electric Motor) CO2, Gas (Green, Red, Propane) and Compressed Air propulsion systems.
Paintball Gun Ammo
Paintball Guns or "Markers" have been historically used for the sport of Paintball but their whereabouts came from the need of ranchers and forestry workers to mark trees. Hence the name "Marker"
Paintball ammo comes in a variety of sizes ranging with the most common being .43 and .68 caliber. They are generally made from a gelatin outer coating containing primarily polyethylene glycol, other non-toxic and water-soluble substances, and dye, they are usually biodegradable.
Paintball Guns can also shoot a variety of Paintball Ammo that can be made out of Rubber, Plastic, Glass and they can also contain Powders and even Pepper for use in non lethal defense.
Paintball Guns can generally use either CO2 or Compressed Air as their propellant.
Blank Gun Ammo
Blank Guns are just like Real Guns but without the dangerous bullet at the end of the brass shell. Other than that they work exactly the same as a Real Gun!
Blank Guns are used when a bullet is not required or even wanted. For instance... Gun safety, gun training, training animals to be around guns and/or loud noises, Props for Movies - Stage - Film - TV, Collectors that do not want the red tape associated with owning a Real Gun or when owning a Real Gun is prohibited.
Blank Guns can shoot a variety of sized ammo, most common are .22 caliber crimped, .380 crimped, 8mm P.A.K. and 9mm P.A.K.
Blank Guns use gun powder as their means of operation.
Here are the most common forms of propulsion used in the guns we discussed earlier:
CO2
CO2 is the most common propellant in Airguns (BB and Pellet), it is also used in Airsoft Guns and Paintball Guns.
CO2 is a compressed gas which expands when released, it requires a warm environment to fully expand and tends to cool it's surroundings quickly when shot fast or in full automatic which can slow the velocity of the projectile and even freeze up the gun being used.
The most common reusable CO2 cartridges are 12 and 88 gram but you can get larger CO2 tanks in a variety of sizes that can be refilled with CO2.
Gas
Gas is used primarily in Airsoft Guns, I have not personally seen an Airgun that is made to use Gas other than CO2.
Gas is similar to CO2 in that it is a compressed gas that expands when releases, it also cools down the gun it is being used in and requires a warm environment.
Gas comes in a variety of names, Green Gas, Red Gas and Propane Gas. Green Gas contains Propane as it's base but has additives in it like silicone for lubrication .
Red Gas is know to be a bit more powerful than Green Gas as it has Chlorodifluoromethane or HCFC-22, R22 or Freon 22 used in refrigeration which turns to a liquid under a slightly higher pressure giving you slightly higher fps.
Many people use propane gas with an adapter that allows the mixture of silicone as propane is cheaper to buy.
Compressed Air (HPA)
Compressed Air (HPA - High Pressure Air) is most commonly used in Airguns and Paintball Guns but some people use it for their Gas based Airsoft guns.
The compressed air comes from high PSI tanks that can be purchased in a variety of sizes and contains compressed air at pressures up to 5000psi.
These tanks are reusable and usually need to be refilled at a paintball or scuba shop, some people buy their own compressors or large scuba tanks for refilling purposes.
Some Compressed Air (HPA) guns have their own built in tanks that can be filled with a compressor or even a manual pump.
Compressed air does not cool down the gun it is being used in and is a great option for high output or fully automatic guns.
Multi-Pump Pneumatic
Multi-Pump Pneumatic systems are most commonly used in Pellet and/or BB guns.
Multi-Pump Pneumatic guns use the same principle as HPA - High Pressure Air guns in that they require pressurized air as the propellant. The main difference with Multi-Pump Pneumatic guns, is that you do all the work by pumping the gun between shots. Generally speaking you pump the gun 3-10 times, take a shot and repeat this process.
Multi-Pump Pneumatic guns are not effected by air temperature and are great for target and small pest control.
Spring Piston
Spring pistons are generally found in Pellet Rifles and Pistols but some Airsoft Guns also use a Spring Piston System and generally speaking Spring Piston Guns are single shot only or in other words, the Spring needs to be drawn back before each shot. Spring Piston Guns can have magazines that allow for quicker repeat shots.
Spring Piston Guns come in many cocking configurations, Brake Barrel and Side lever to name a couple.
The Spring can be a Mechanical Spring or a Gas Spring.
Spring Piston Guns are not effected by temperature and are often used for small game hunting and target shooting.
Automatic Electric Guns (AEG)
Automatic Electric Guns are generally found in Airsoft Rifles but there are some Airsoft Pistols (AEP) that use this same system.
Automatic Electric Guns use a similar system to a Spring Piston gun but have an electric motor that does all the work of drawing back the spring. You can even have fully automatic AEG guns.
The power for the electric motor comes from removable batteries, so it is a combination a battery supplying the motor with the power to draw back the spring that creates a pillow of air that shoots the BB.
AEG Airsoft Guns are great for situations when you require high capacity magazines with full auto capability.
Gun Powder
Gun powder is used in Blank Guns, in the same manor that it is used in a Real Gun, the charge from the Gun Powder supplies the force required to operate the blowback in most semi auto Blank Pistols, it also creates the sound of a live round along with the muzzle flash which makes Blank Guns great for training and as Props for Movies and Film.
Because the kinetic energy from a blank gun is the same as a real gun, blank guns can be very dangerous when used in close proximity to an object, see my "Are Blank Guns Dangerous Video"!
Some other Gun Relevant Terminology:
Blowback
Blowback operation is when some of the force of the propellant is used to move the slide backwards, which in most cases cocks the hammer for single action and can also pickup and chamber a round into the barrel.
The slide spring supplies the energy for the return to the forward position of the slide.
Blowback Guns do rob some power from the bullet force and in the case of CO2 or Gas Guns the also reduce the amount of shots per CO2 or Gas fill.
Revolver, Semi Automatic
Revolver: Revolvers feed ammunition via the rotation of a cartridge-filled cylinder, in which each cartridge is contained in its own ignition chamber, and is sequentially brought into alignment with the weapon's barrel by a mechanism linked to the weapon's trigger (double-action) or its hammer (single-action)
Semi Automatic: semi-automatic pistols use the energy of one shot to reload the chamber for the next. Typically recoil energy from a fired round is mechanically harnessed. After a round is fired, the pistol will cycle, ejecting the spent casing and chambering a new round from the magazine, allowing another shot to take place immediately.
Single Shot, Repeater, Semi Automatic & Fully Automatic
Single Shot: A Single Shot Gun needs to be reloaded each time it is shot.
Repeater: Repeating action Guns are single barreled guns containing multiple rounds of ammunition. These rounds are loaded from a magazine by means of a manual or automatic mechanism, and the action that reloads the rifle also typically re-cocks the firing action. The term repeating rifle is most often applied to weapons in which the next cartridge is loaded by a manual action, as opposed to semi-automatic rifles, in which the force of one shot is used to load the next.
Semi Automatic: A semi-automatic, or self-loading, firearm is a weapon that performs all steps necessary to prepare the weapon to fire again after firing.
Fully Automatic: A Gun that uses either its recoil or a portion of the gas propelling the projectile to remove the spent cartridge (in the case of a gun-shell), fire again repeatedly, as long as the trigger is held down or until the magazine is exhausted. Automatic Guns are distinguished from semi-automatic Guns in their ability to fire more than one shot in succession once the trigger is pulled.
Single-Action (SA): trigger performs the single action of releasing the hammer or striker to discharge the firearm each time the trigger is pulled.
Double-Action (DA): The trigger both cocks and releases the hammer or striker
SA-DA: A SA/DA firearm combines the features of both mechanisms. You can pull the trigger in Double Action when the hammer is down which cocks and releases the trigger or you can cock the hammer with your thumb and then release the trigger using Single Action to fire the weapon.
Lever Action, Pump Action, Bolt Action
Lever Action: In a classic lever-action firearm, rounds are individually loaded into a tubular magazine parallel to and below the barrel. A short bolt is held in place with an over center toggle action. Once closed, the over center action prevents opening solely by the force on the bolt when the weapon is fired. This toggle action is operated by a hand grip that forms part of the trigger guard. When operated, a spring in the tubular magazine pushes a fresh round into position. Returning the operating lever to the home position chambers the round and closes the breach.
Pump Action: With a pump-action firearm, the action is operated by a movable fore-end that goes backwards and forwards to eject, extract, and chamber a round of ammunition. Pump-actions are usually associated with shotguns.
Bolt Action: The bolt opens and closes the breech end of the barrel and contains the firing pin. The bolt is held in place with a lever that fits into a notch. Moving this lever out of the notch will release the restraint on the bolt, allowing it to be drawn back. An extractor removes the spent cartridge, which is then ejected through the lever slot. A spring at the bottom of the magazine pushes up the reserve rounds, positioning the topmost between the bolt and the chamber at the base of the barrel. Pushing the bolt lever forward chambers this round and pushing the lever into the notch locks the bolt and enables the trigger mechanism.
Magazine vs Clip
Magazine: A magazine is an ammunition storage and feeding device within or attached to a repeating firearm. Magazines can be removable (detachable) or integral to the firearm. The magazine functions by moving the cartridges stored in the magazine into a position where they may be loaded into the chamber by the action of the firearm. The detachable magazine is often referred to as a clip, although this is technically inaccurate.
Clip: A clip is a device that is used to store multiple rounds of ammunition together as a unit, ready for insertion into the magazine or cylinder of a firearm. This speeds up the process of loading and reloading the firearm as several rounds can be loaded at once, rather than one round being loaded at a time. The term "clip" is also frequently used to refer to a detachable magazine, though such usage is incorrect.
I wanted to show off a few new items that I will be reviewing, one being the Crosman MK-177 Pellet and BB pneumatic multi-pump air rifle that was very graciously provided to me by Crosman for review. And the other item is something kind of new in terms of the type of gun, since it is not really gun but rather a bow, or crossbow to be exact. We hope to be adding to our Replica Airguns Store a couple variations of the Avalanche Trailblazer 150lb Crossbows in wood stock and polymer stock versions.
Here are a couple key points about each item being looked at in this update video and then I will leave you with some detailed photos to drool over and of course my YouTube Update Video to watch...
Crosman MK-177 multi-pump bolt action .177 caliber BB/pellet air rifle:
Shoots both .177 caliber pellets and 4.5mm Steel BB's
Maximum 800 FPS (US Version being reviewed here)
5 shot pellet magazine and 300+ BB reservoir
Multi-pump single shot bolt action
3-10 pumps per shot
16.75 inch rifled barrel
3.5 pounds
Mostly plastic with some internal metal parts
Avalanche Trailblazer 150lb Crossbow with Wood Stock:
Action: Semi auto, double action only with blowback.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 15 round stick magazine.
FPS: 380.
Trigger Pull: The Double Action Only trigger pull on the Umarex Walther P99 CO2 Blowback Airsoft Pistol is long but not overly heavy for a double action trigger, it does have a break point mid way where it locks partway back, I presume this is the point in which a BB is loaded from the magazine into the barrel? The rest of the pull is still medium but much shorter with a distinct release point.
Accuracy: I did do a quick preliminary test before I made this table top review to get an idea of where this gun performs in terms of FPS and accuracy, I shot 5 rounds through my Chronograph on a fresh CO2 and got an average of 333FPS which was a bit lower than the claimed 380 but it was not the hottest of days. I also stepped back 20 feet and from a semi rested position I was able to get 9 shots within 2 inches of each other which was not bad for a DAO gun that I have never shot before. I did shoot a bit down and to the left with the set sights.
Build Quality: The Umarex Walther P99 is well built for its rather low price tag, it may not have all the bells and whistles but it does get the job done with good fit and finish and materials used. You will find a plastic/polymer frame but there is a lot of metal where it would normally be found on the real steel version like in the slide, magazine, trigger, slide catch, magazine release, inner barrel and many other internal parts. No real complaints here!
Realism: The Umarex Walther P99 CO2 Blowback Airsoft Pistol is pretty close in looks to a real steel Walther P99 with the exception of a missing decocker, but I'm pretty sure this is the same with the real steel DAO version? There is also the funny looking safety on the right side of the frame found on many Umarex airguns. I have to mention the red tip but again this can be removed and even when removed the barrel it is still recessed which adds to the realism. The Blowback action, Walther licensing and nice heavy weight all add up to make this Airsoft pistol look and feel the part.
Metal slide and internal parts gives it decent weight.
Rail for accessories.
Well hidden CO2 screw.
Walther licensing.
Recessed inner barrel.
White dot sights, easy to use.
Right amount of power for indoor CQB style airsoft games.
Cons:
Comes with a red tip even in Canada.
Double action only, so trigger is a bit heavier.
Kind of funny safety, not like the real gun.
Blowback was a bit sluggish.
Comments:
Overall the Umarex Walther P99 CO2 Blowback Airsoft Pistol is a very good buy, it's a decent replica of the real steel Walther P99 with blowback operation, lots of metal parts, good fit and finish, decent performance and full Walther licensing and trademarks. All at a very affordable price tag. It may lack some of the extras you will find on more expensive and more functional Airsoft pistols but the simplicity of the Umarex Walther P99 CO2 Blowback Airsoft Pistol means it will most likely be a bit more reliable with less to go wrong down the road. If you have been looking for a nice Walther styled replica in an Airsoft version this may be just be the ticket!
My Vimeo Video Review for the Umarex Walther P99 CO2 Blowback Airsoft Pistol:
I will be doing proper Table Top and Field Test Videos for each of these Airsoft guns as soon as I can get to them all, starting with the Umarex Gas Blowback H&K MP7 A1 Airsoft PDW so stay posted for these upcoming video reviews...
After many many requests to show how the Umarex Walther PPK CO2 Tab Modification is done I have relented to public demand. I don't actually cut my tab in this PPK CO2 Tab Modification Video but I do go step-by-step in detail and compare my modified Umarex PPK to my unmodified Umarex PPK. It is really very basic on how this is done and only a hack say and perhaps a file are all that is required to make the modifications to the PPK CO2 tab in order to make it flush with the bottom of the handle area.
Your best bet is to simply watch my YouTube Video located below and follow the steps there but here it is in text form:
Place an empty (already pierced) CO2 into your Umarex Walther PPK and tighten the unmodified CO2 tab until fully tightened, just like you would tighten a fresh CO2.
Take note at how many threads are exposed between the bottom of the handle and the top of the plastic CO2 tab, there should be about 2-4 threads exposed.
Unscrew the CO2 tab all the way, place the PPK BB Pistol so it is secure (in a vice of some sort) and use a hacksaw or dremel to shorten the CO2 screw just above the plastic tab at the thread location you previously noted. Be conservative as you can always cut or file the screw a bit shorter if your first cut was not short enough.
Now use the same hacksaw or dremel to cut a notch in the exposed cut area of the CO2 screw so that you can use a slot screwdriver to tighten the CO2 screw.
That's it - Enjoy your modified Umarex Walther PPK CO2 BB Pistol!
Watch my Vimeo Video of the Umarex Walther PPK CO2 Tab Modification Tutorial:
This is not meant to be a full review of either the BB or Airsoft version of the Cybergun - KWC CO2 Blowback Mini UZI's but I do talk about specifications, show you around both guns, and put them both through a full Field Test so I guess in a way, perhaps it can be considered to be a full review ;)
I will list the specifications here for you but I am not going to get into details like Trigger Pull, Build Quality, Accuracy and Realism. You can check out my other video reviews for more information on the Mini UZI:
As I said you can check out all my other videos for info on these very accurate Mini UZI Replicas, I mainly want to go over some of the main differences and similarities for both the BB and Airsoft versions.
In terms of build quality they are made almost exactly the same and weigh in at a hefty near 5 pounds, the only differences are the inner barrel and magazines to accommodate the different sized ammo. The BB version has a 25 round single stack magazine that does not have a follower to stop the bolt from continuing to operate even after the magazine is empty. While the 6mm Airsoft version has a double stack magazine that holds 38 rounds and does have a follower to stop the bolt which can save you some unintentional wasted CO2.
The Airsoft Mini UZI version is distributed by KWC while the 4.5mm BB version is distributed by Cybergun, you will find the UZI and IWI licensing on the Cybergun 4.5mm BB version but not on the KWC 6mm Airsoft version.
Out of the box the KWC Airsoft Mini UZI is ready to go in both semi auto and full auto while the 4.5mm steel BB version will only shoot in semi auto mode, it can however be easily modded to shoot in full auto.
Both guns come in cardboard boxes with manuals, some BB's and an Allen key to tighten the CO2. The KWC Airsoft Mini UZI also comes with a handy speed loader.
There is a slight fps velocity difference between the two with the KWC Airsoft 6mm plastic rounds traveling at around 400 fps (with .20 gram BB's) and the 4.5mm Steel BB's traveling at right around 350 fps. In the field test portion I test both guns out on some water filled cans to see how each ammo type performs in terms of penetration.
Your best bet is to watch both my Table Top and Field Test Comparison Video Reviews and see for yourself how they compare!
I don't often get to shoot my airguns out at the 100 foot mark but I purchased my Sheridan Silver Streak .20 Caliber Multi Pump Pellet Rifle mainly to shoot up to and even past this fairly distant range as the Silver Streak is my new vermin gun for pests around the farm. I get a lot of Crows that to be honest are just feathered bullies that pick on all the other friendly birds on the farm, they have also been known to get into my garbage and even attack the Eagles and Hawks in the area. Flying Rats I like to call them.
In this Field test Shooting video I test out my brand new Sheridan Silver Streak on the Chronograph to see just how powerful it really is not just at the maximum 8 pumps but also at 3 and 5 pumps. I was actually very surprised at the very decent power I got from only 3 pumps (460 fps), you could easily take out a small rat with the 14.3 grain .20 caliber lead pellets I was using for my Chrony test. At 5 pumps I gained close to another 100 fps and at 8 pumps I maxed out at just a hair under 640 fps respectively. With the 14.3 grain pellets I was using this worked out to right around 13 foot pounds of energy. (My Sheridan was purchased using a PAL)
I also shot my Sheridan Silver Streak .20 Caliber Pellet Rifle at a target setup 100 feet or just over 30 yards away and was able to get what I felt was a nice 1.5 inch 5 shot grouping. 4 of the 5 pellets where all within 1 inch of each other with my first shot being a bit lower and to the right of the rest spreading the group out to about 1.5 inches. Keep in mind I was also a bit winded from all the pumping and I could feel and see my heartbeat in my 9 power Bushnell scope making my crosshairs bob back and forth ever so slightly.
I have not shot my Sheridan Silver Streak all that much and plan to hone my skills further so when the time comes I will be ready for them pesky crows.
Stay tuned for my future Table Top review of my Sheridan Silver Streak, for now you can checkout my Preview video that has some preliminary info.
I like to show off some of my acquisitions from time to time even if they are guns I don't necessarily have for sale, I am a collector and some items are not always common enough or even popular enough to keep in our Replica Airguns Store.
Today I show you two blank guns I picked up from a recent gun show I attended in Chilliwack BC. There where not many blank guns at the show, the two I found may have been the only blank guns there, at least that I saw? The ROHM RG300 .22 Caliber Blank Pistol and RST MOD. 1966 .22 Caliber Blank Revolver I picked up for a pretty good price, at least in my mind, $55 for the ROHM and $20 for the RTS. A nice addition to my blank gun collection!
I have been contemplating between a PCP (Pre Charged Pneumatic) or a really good Multi-pump air rifle for pest control around my house, I have been using a spring piston rifle but the combination of my limited skills with spring piston rifles and the fact that most pests in my area stay a good 50+ yards back, means I need an airgun with pin-point accuracy. At the end of the day I decided on the Sheridan Silver Streak because it was a bit more affordable than a PCP air rifle and also the Sheridan is such a classic air rifle but still with the right amount of power and accuracy to get the job done.
Trigger Pull: The trigger pull on the Cybergun Sig Sauer P226 Airsoft Replica is good in both single and double action. Once the slide is pulled back and released the first round is chambered and the hammer will remain back placing the P226 in single action mode, the pull is light and the take-up is fairly short, most of your shots will be in single action mode unless you use the de-cocker to lower the hammer for a subsequent double action next shot, double action shots are still pretty light but much longer in order to cock the hammer.
Accuracy: Shooting the Cybergun Sig P226 from 20 feet out in semi rested position I was able to get very good results. I placed 10 rounds in about 1.5 inches with the shot placement being a bit low possibly due to my barrel mod, adjusting the hop-up may bring the aim point back up to where it should be. The Sig Sauer P226 Airsoft Replica shot right around the 316 fps range while conducting my 5 shot average chrony testing which was lower than advertised but I was using much heavier .20 gram BB's. You can expect to get a full magazine worth of shots out of each gas fill-up but I did notice that as the magazine got colder it did tend to become much less efficient and also seemed to vent a lot of vapor.
Build Quality: The build quality is generally good and I was surprised at the finish on this model as the paint is not showing any wear marks so far, the fit is good with minimal slide and barrel wobble and everything is working very well with no problems so far with a fair amount of shots through it, guess you could say I like shooting this gun :) Most of the gun is metal with only the grips and a couple internal parts being plastic.
Realism: The Cybergun Sig Sauer P226 6mm Airsoft pistol is a replica of the real steel Sig Sauer P226 right down to the licensing and it really is a great looking and functioning Airsoft Replica. You can field strip this gun exactly like a real Sig and all the mechanical parts work just the same including a working de-cocker and adjustable front sight.
Seemed to shoot a bit low for me, could adjust with hop-up a bit?
Only one magazine per Gas fill.
Comments:
I am a big Sig Sauer fan so it would take a lot for me to not give this gun a good review, with that said it performed pretty well, sure it was not the most powerful but I was using gas over CO2 so I was not expecting too much, it also shot a bit low for me but again that may have been because of the barrel mod so who really knows for sure at this point ;) And yes it came with that unsightly orange tip that I took short work of removing. At teh end of the day I still love it and it performed well without letting me down, just like a would expect from a real Sig Sauer!
My Vimeo Table Top Review of the Cybergun Sig Sauer P226 GBB Blowback Airsoft Pistol:
I usually do my Table Top Video Review first but this time around I did my Field Test Video Review first since I was all setup checking out a couple other guns at the time. When I do my detailed Table Top Video Review for the Cybgergun Sig Suer P226, I'll post the link here so stay tuned. If you have not already checked out my Barrel Mod Video for this same gun then check that video out where I remover the extended orange portion of the metal barrel and make the barrel flush with the end of the slide which is how the real steel version was originally made.
Getting back to the Cybergun Sig Sauer P226 GBB blowback Airsoft Pistol field test, as per usual I test this Airsoft semi auto gas blowback pistol on the Chronograph to see what kind of real world velocity I get and since I had some Green Gas on hand, I used it for this part of the review and got an average of 315 fps with a six shot string.
I also stepped back 20 feet and shot 10 times at my stationary target using a semi rested position (sand bag up front and kneeling in the back). Even though the Sig Sauer P226 shot a bit low I did get about a 1.25 inch group with the exception of one flyer that hooked down just a bit making the 10 shot group a bit wider at just under 2 inches. The low shot placement may have been caused by my barrel mod but since I did not do a before and after test, I can not say for sure?
Make sure to watch my YouTube Video of this Field Test as it also includes some nice slow-motion of the slide blowback at both 400 and 1200 frames per second.
Watch my full Video Field Test Shooting Vimeo Video below:
I have not done my official Table Top and Shooting Reviews for the Gas Blowback Airsoft Cybergun Sig Sauer P226 but I really wanted to cut off the ugly orange painted barrel tip, it was kind of driving me crazy! keep in mind here in Canada we are not required to have orange tips on our Airsoft guns, most of the all metal or all black Airsoft guns imported these days fall into the "airgun uncontrolled firearms" category. If you live in the US or other parts of the world you could be breaking the law if you do this mod so be warned...
Your best best is to simply watch my Vimeo Video as I show you exactly how I removed the orange painted portion of the metal barrel using a hack saw, file, vice and some sand paper. All in all it was not too difficult and only took about 15 minutes to complete...
