I usually do my Table Top Video Review first but this time around I did my Field Test Video Review first since I was all setup checking out a couple other guns at the time. When I do my detailed Table Top Video Review for the Cybgergun Sig Suer P226, I'll post the link here so stay tuned. If you have not already checked out my Barrel Mod Video for this same gun then check that video out where I remover the extended orange portion of the metal barrel and make the barrel flush with the end of the slide which is how the real steel version was originally made.
Getting back to the Cybergun Sig Sauer P226 GBB blowback Airsoft Pistol field test, as per usual I test this Airsoft semi auto gas blowback pistol on the Chronograph to see what kind of real world velocity I get and since I had some Green Gas on hand, I used it for this part of the review and got an average of 315 fps with a six shot string.
I also stepped back 20 feet and shot 10 times at my stationary target using a semi rested position (sand bag up front and kneeling in the back). Even though the Sig Sauer P226 shot a bit low I did get about a 1.25 inch group with the exception of one flyer that hooked down just a bit making the 10 shot group a bit wider at just under 2 inches. The low shot placement may have been caused by my barrel mod but since I did not do a before and after test, I can not say for sure?
Make sure to watch my YouTube Video of this Field Test as it also includes some nice slow-motion of the slide blowback at both 400 and 1200 frames per second.
Watch my full Video Field Test Shooting Vimeo Video below:
My 5 shot Chronograph test resulted in a lower than expected 308 average fps while my accuracy test shot from 20 feet out in a semi rested position this time received a just over 2 inch group but with most shots being within 1 inch, I have found with Airsoft guns that there can be some floaters perhaps due to inconsistencies with some of the ammo. In terms of shot placement the KJWORKS KP-05 HI-CAPA 1911 shot very well centered only being just slightly high and to the left but only marginally. I was also able to get 2 full magazines plus another half mag this time around so just over 60 shots with the KP-05.
KJWorks KP-05 1911 HI-CAPA Airsoft Pistol although not shooting as hard as I though it would still performed great for me and would make a great field gun as it performs very well and has a nice high capacity magazine which would come in handy in the heat of battle.
My 5 shot Chronograph test resulted in a very respectable 366 average fps while my accuracy test shot from 20 feet out in a semi rested position this time around came in a bit higher than my pre test right at around 2 inches. Several of the shots hit right on top of each other. In terms of shot placement the KJWorks KP-09 CZ 75 shot fairly well centered but just a bit high and a tad to the left. I was also able to again get 3 full magazines or around 75 shots out of this heavy blowback Airsoft pistol.
KJWorks KP-09 CZ 75 Airsoft Pistol really has a lot going for it, it's a great Replica of a real steel CZ 75 with a very nice single action trigger, it has great snappy full blowback with excellent fps and accuracy and it even gets a solid 75 shots out of a single CO2 which is very good for this style of full blowback gun.
I have not done my official Table Top and Shooting Reviews for the Gas Blowback Airsoft Cybergun Sig Sauer P226 but I really wanted to cut off the ugly orange painted barrel tip, it was kind of driving me crazy! keep in mind here in Canada we are not required to have orange tips on our Airsoft guns, most of the all metal or all black Airsoft guns imported these days fall into the "airgun uncontrolled firearms" category. If you live in the US or other parts of the world you could be breaking the law if you do this mod so be warned...
Your best best is to simply watch my Vimeo Video as I show you exactly how I removed the orange painted portion of the metal barrel using a hack saw, file, vice and some sand paper. All in all it was not too difficult and only took about 15 minutes to complete...
Trigger Pull: The trigger pull on the KJWORKS KP-05 is what you would expect from a true 1911 single action only trigger, it has very little take up with a smooth crisp and light release to it.
Accuracy: I shot the KJWORKS KP-05 from 20 feet out in semi rested position and got very good test results. I was able to place 10 rounds in under 1.5 inches and getting four shots right in the bullseye making the shot placement very good even without adjusting the sights (which can be adjusted for windage). The KJWORKS HP-05 1911 styled HI-CAPA Airsoft Replica shot right around 300 fps range while conducting my 5 shot average chrony testing which was surprisingly low for the CO2 magazine version, this may have been a temperature or CO2 related condition, when I conduct my full Field Test Shooting Review, I will review this and see if we can do better? I also got two full 30 round magazines worth of shots which is what you would expect from this style of full heavy blowback airsoft pistol.
Build Quality: I am extremely impressed with the build quality of all the KJWORKS Airsoft guns so far, the fit and finish is the best around on any of my guns including my 4.5mm steel BB shooters. After shooting several magazines worth of BB's, areas that are painted like the metal friction areas show very light wear which is rarely the case with metal built blowback airguns. Again the tolerances between the moving parts like the slide and frame are very tight showing excellent workmanship and machining from KJWORKS.
Realism: The KJWORKS KP-05 6mm Airsoft pistol is a replica of a High Capacity styled tactical 1911 45 Auto and is a great looking and functioning replica. You will not find any actual licensing on this pistol and the CO2 magazine does stick out a bit to accommodate the 12 gram CO2 but other than that this Airsoft pistol looks and works near exactly like a real 1911 tactical semi auto and is fully field strip-able. I really like the updated more tactical add ons like the tactical rail, machined trigger and hammer, white dot adjustable sights, wrap around grips and ambidextrous safety.
All metal pistol with good overall realistic weight to it.
Full heavy blowback operation.
Typical KJWORKS excellent fit and finish.
High capacity magazine 30 rounds.
Very good accuracy and well centered on target.
Nice replica of a High Capacity Tactical 1911 styled pistol.
I like the stainless highlights and ambidextrous safety and Rail for accessories.
Fully field strip-able.
Cons:
Shot a bit low Feet Per Second for me - should do better?
CO2 magazine is long to accommodate the 12 gram CO2.
Slide is heavy enough but seems to be a bit sluggish which is kind of a 1911 trademark so that can be taken as good or bad.
Comments:
The KJWORKS KP-05 1911HI-CAPA is another excellent full blowback Airsoft pistol from KJWORKS. The HP-05 is a classic upgraded more modernized version of the 1911 semi auto pistol which is a great foundation to build any pistol from. I found the CO2 usage to be decent on the KP-05 but felt that I should have been able to get more fps out of this pistol, I will be testing the KJWORKS KP-05 again and hope to see some better results in this area. With that aside, the KP-05 1911 HI-CAPA is a great shooter and as is, with its high capacity magazine would be a perfect sidearm for any Airsoft related squirmish or even just for honing up your shooting skills when getting to the gun range is not an option.
Trigger Pull: The trigger pull on the KJWORKS KP-09 CZ 75 Airsoft Replica is surprisingly light in single action but incredibly sticky at first in double action, with that said you really will not be shooting very often in double action unless you happen to de-cock the gun for some reason, at least you have the ability to shoot with the hammer down in double action when required. In signal action it took me a bit to get used to the very light trigger pull as I was letting some shots go off early.
Accuracy: I shot the KJWORKS KP-09 from 20 feet out in semi rested position and got very satisfactory results. I was able to place 10 rounds under 2 inches almost getting a 1 inch group with the exception of one flyer. Shot placement was also well centered but just a bit high which could easily be corrected by adjusting my aim point just a bit down. The KJWORKS CZ 75 Airsoft Replica shot right around the 360 fps range while conducting my 5 shot average chrony testing which is right where this gun is supposed to be. I also got three full 24 round magazines worth of shots with a bit of CO2 left over for a partial mag, so this gun can easily get 75 shots out of a 12 gram CO2 - not bad at all for this style of full heavy blowback airsoft design.
Build Quality: I am extremely impressed with the build quality of pretty much all the KJWORKS Airsoft guns, the fit and finish is the best I have seen on any of my guns including my 4.5mm steel BB shooters. Even after shooting several magazines worth of BB's, the painted metal friction areas show very light wear which is not always the case with metal built blowback airguns. (there was some wear present within the ejection port but this is common even with real steel guns as metal on metal will wear down the finish). The tolerances between the moving parts like the slide and frame are very tight showing excellent workmanship and machining.
Realism: The KJWORKS KP-09 6mm Airsoft pistol is a replica of the real steel CZ 75 and is a great looking and functioning copy. You will not find actual licensing on this version and the CO2 magazine does stick out a bit to accommodate the 12 gram CO2 but other than that this Airsoft pistol looks and works near exactly like the real mccoy and is full field strip-able. Even the safety operates just the same with safety available on half cock and full cock only.
All metal pistol with good overall realistic weight to it.
Very crisp and firm full blowback operation.
Excellent fit and finish - best I have seen.
Excellent fps and CO2 efficiency (three plus full 24 round magazines)
Good accuracy and well centered on target.
Very believable working replica of the real steel CZ 75.
Fully field strip-able.
Cons:
Does not have official CZ 75 licensing.
CO2 magazine is long to accommodate the 12 gram CO2.
Did get some finish wear in the ejection port area.
Comments:
The KP-09 CZ 75 is another wonderful full blowback Airsoft pistol from KJWORKS. The CZ 75 is a classic semi auto pistol and deserves the attention to detail the KJWORKS version demonstrates. I found the CO2 usage to be very good on the KP-09 considering the rather high 360+ fps I was abel to get with it. Top this off with high marks in the accuracy department and you have a real winner here. So if you're looking for a quality Airsoft Replica of the classic CZ 75 that shoots straight and hard and looks and operates just like the real steel version then the KJWORKS KP-09 should just do the trick for you.
Here's a heads up on some new items we will be adding to the Canada Replica Airguns Store very soon so keep checking back if you're interested in them!
Your best bet is to Watch My Vimeo Video as I go over them all and show you around the new products, but for now here is some basic info on each item:
I am happy to report back to you on all the new cool stuff I got to see at this years 2013 SHOT Show in Las Vegas. Make sure to also watch my Vimeo video at the bottom of this post for some first person styled play by play of my experience at the Vegas SHOT Show 2013. (like you're there with me ;)
First up I want to cover a new gun from ASG, I have been wanting to get my hands on the 4.5mm Bersa BP9CC and I finally got to, not only did I get my hands on it but ASG was kind enough to supply me with one to take home for review. You can get the Bersa BP9CC in both Blowback and non-blowback versions and also in either BB or Airsoft. I opted for the 4.5mm BB Blowback version. I will be reviewing this BB gun very soon!
ASG also had a very cool prototype of an Airsoft CZ Scorpion EVO 3A1 hopefully coming out soon.
While roaming around SHOT Show 2013, I came across an interesting booth from FlashFog Security. I often get people asking me about using an airgun as a home defense weapon and I strongly advise against this. If the intruder is not scared off by the gun there is little an airgun can do to actually stop them. The FlashFog system works by rapidly filling a room with dense fog combined with a strobe light effect which blinds and disorients intruders completely. There is little an intruder can do other then try and get the heck out of there!
UPDATE: FlashFog just added a new section to their website specifically for School Security to help keep our schools safer from potential safety threats! So check it out: School Security Smoke Screen
I was a bit surprised by Gamo this year, they tend to stay away from actual Replica's and generally make BB/Pellet guns that look like popular guns but not any gun in particular. Gamo has a new BB/Pellet MP9 based machine pistol that uses a similar mechanism to their P-25 and PT-85 so it can shoot both 4.5mm BB's and .177 caliber Pellets using a double ended 16 shot rotary magazine. It also has an internal blowback system so it should have some recoil feel to it! I am pretty sure it is semi auto only but still a nice addition to their lineup!
Gamo also brought out a new 4.5mm BB Blowback pistol called the C-15 which has a metal slide and plastic frame, it kind of reminds me of the Umarex HPP in how it looks and feels.
Umarex had several new products that I am sure everyone is going to like! One that I think will do really well is the Steel Force, the Steel Force is designed around the 4.5mm BB shooting Steel Storm platform so it has a 6 round burst blowback operation and holds the 2x12 gram CO2 in the magazine while the BB's go in a 300 round hopper that feeds into a 30 round spring fed internal magazine. Like the Steel Storm it will shoot around 430 fps. The Steel Force has the advantage of being styled after the AR platform so it has a collapsible stock which will make shooting very easy.
Another often asked for airgun replica is the historic German Luger. This year Umarex stepped up to the plate and introduced the Umarex P.08 4.5mm BB pistol. Sorry, no blowback or even a working slide on this one but it is all metal and has a very good weight and feel to it.
If you're a fan of the entry level Umarex XBG then you may be interested in the new Umarex T.D.P. 45 which is very similar to the XBG in looks and features but with a slightly different look to it.
If you've ever wanted to turn your pistol into more of a PDW styled gun, you may be able to depending on which Umarex gun you have? Umarex added a very cool accessory called the T.A.C Converter that converts your Umarex HK USP (BB-Airsoft), SW MP40 (BB), XBG (BB), CZ Enforcer (Airsoft) and Walther P99 DOA (Airsoft) into more of a tactical (PDW) or Personal Defense Weapon complete with for-grip, adjustable rear sight, lots of rail options and a foldable stock.
I am assuming the Crosman M4-177 Pellet/BB Rifle has been doing well for Crosman as they have expanded with some more similar assault styled air rifles. The Crosman MSR77NP pretty much looks like a classic M16 but is in fact a Nitro Piston break barrel pellet rifle able to shoot .177 caliber pellets at 1200 fps (I hope there is a 499 fps Canada version planned too?).
A new takeoff of the M4-177 is the MK-177 which also shoots .177 caliber pellets and 4.5mm BB's using a multi-Pump System but it uses an upgraded more efficient pump system that squeaks out more fps with less pumps. The Crosman MK-177 is designed after the FN SCAR and is available in an adjustable iron sight version or a Red Dot equipped kit version.
One thing you can never get enough of in my opinion is another 1911 pistol! Crosman is introducing their GI Model 1911BB Blowback 4.5mm CO2 pistol, the one they had on hand was more of a prototype so the slide was not operational but it will feature an all metal design, blowback operation, 450 fps and a 20 round drop out magazine. I am sorry to say but it looks like the Crosman C51 has been dropped from Crosman's lineup but if you want a similar styled gun you can checkout the KWC SW40F which is a very close airsoft version.
We recently started carrying G&G Armament Airsoft guns, you can checkout my review of the Xtreme 45. I did stop by their booth and they had some new products on display, the M1 Grand (all wood stock) Airsoft had it's magwell all wrapped up as G&G had a propriety magazine system they did not want their competition to see. G&G also had some very interesting targets that light up, when shot they would react by individually turning off so you could see if you hit it or not.
There was a rather large crowd at the KWA booth but it was a shared booth so it's hard to say what everyone was looking at, the KWA area was pretty full, I did talk to the KWA rep and asked him point blank if KWC and KWA where the same or sister companies and the answer was not at all. There are often a lot of guns that look like they could be from the same company, I guess there is a lot of copying going on ;) One gun from KWA I would love to get my hands on is the Kriss SMG!
Now keep in mind many of these guns I have highlighted today are not available yet and a lot of them should be coming out in the spring time frame so please try to refrain from repeatedly asking when I will review them and have them in the store, it takes time and as much as we all want them now, they get here when they get here!
Watch my Vimeo video of the Replica Aiguns at SHOT Show Vegas 2013
I've already done a KJWORKS review on the KP-02, KP-07 and Elite 1A and they turned out to be very high quality Airsoft pistols so the extra price does get you a higher quality gun. So in this preview we are simply looking at some more models that from the looks of things I expect to be more of the same in terms of high quality and excellent functionality.
The KJWorks models we are looking at today are the KP-05 (1911 HI-CAPA), the KP-09 (CZ 75) and the M9 (Beretta M9). Even though none of them are licensed, they are very detailed and realistic copies of the original real steel versions with full blowback operation, heavy metal drop out magazines and lots of metal throughout. You would be hard pressed to tell them apart from the real powder versions.
All version in this preview load CO2 in the magazine along with 6mm Plastic Airsoft BB's, none of them have any orange markings or translucent parts as they fall into the uncontrolled firearms category here in Canada.
I look forward to doing my full review of these three very nice KJWorks Airsoft pistols.
I have talked about how KWC and Cybergun are really the same product and that Cybergun and KWC products in many cases are really the same gun but with some versions having slightly different markings on the guns themselves.
Today I show you a new 4.5mm Steel BB gun we just brought into the store very closely related to the Cybergun Tanfoglio Witness 1911, or otherwise known as the KWC Model 1911. This new airguns is a Tactical version of the Model M1911 and it goes by the name Model M1911 A1 Tac. It shares the same internal parts as the Tanfoglio Witness 1911 including the 4.5mm Steel BB magazine but the Tactical version is all black and has several updated modern parts that you would not find in a traditional 1911 A1 45 auto replica: Like the tactical trigger, hammer, adjustable white dot sights and accessory rial. This gun would make an awesome IPSC trainer for sure.
At this point there is no 6mm Airsoft version but you can get the KWC Model 1911 and M92 in 6mm Airsoft all metal versions.
I also compare my GSG 92 4.5mm Steel BB pistol I reviewed in the past and show you that it is identical to the KWC same M92 version with the exception of some marking on the slide. Many people even prefer the KWC branded models as they do not have the rather offensive white warning instructions all over them.
So if you're in the market for one of these super popular KWC/Cybergun blowback ultra realistic BB and Airsoft pistols you do have some options to consider...
Watch my Vimeo Video Preview for these very popular KWC/Cybergun Blowback Pistols:
In this part of the review I test the HK G36 KV AEG Rifle using my Chronograph to see what the 5 shot feet per second average is using fully charged batteries. I got pretty much right bang on to the factory claimed 450 fps using .20 gram 6mm plastic Airsoft BB's and consistency was within a few fps for each shot.
I also take the Umarex HK G36 KV AEG Blowback (EBB) Airsoft Rifle back 30 feet and shoot it at a target using a semi rested position (sand bag up front, standing in the back) and shoot in both semi auto and full auto, there really was no real difference in accuracy using both selections, I think the built in magnified scope helped out here to get a very tight 1.5 inch group shooting in semi and full auto.
So far out of all my AEG rifles I would have to say the Umarex HK G36 KV (EBB) performed the best getting very consistent and high fps and tight groupings in both semi and full auto even using light weight .20 gram BB's.
Watch my Field Test Shooting Vimeo Video Review for the Umarex HK G36 KV AEG Blowback Airsoft Rifle:
This is the official Field Test or Shooting Video Review for the G&G Xtreme 45 CO2 Blowback Airsoft Pistol. If you haven't checked out my Table top Video Review for the G&G Xtreme 45, make sure to do so as I have some more photos there and also all the specifications and details including the Pros & Cons for the G&G Xtreme 45.
In this part of the review I test the G&G Xtreme 45 CO2 Blowback Airsoft Pistol using my Chronograph to see what the 5 shot feet per second average is using a mostly brand new CO2. I got pretty close to 400 fps which is not bad considering the very cold day and the fact that I had to reset my Chronograph and missed the most powerful first several shots.
I also take the G&G Xtreme 45 back 30 feet and shoot it at a target using a semi rested position (sand bag up front, standing in the back) and again I was plagued by technical difficulties and had to redo this part of the test as one of my cameras was not working. I did get a nice 2 inch 10 shot grouping the first time around, the second go resulted in a 3 inch 10 shot group which is pretty good for an airsoft pistol using light weight .20 gram BB's at this range.
All in all the G&G Xtreme 45 CO2 Blowback Airsoft Pistol performed very well for me and considering the fairly low price point and long list of features I would have to say it is good value for the low cost, and it has some pretty nice curb appeal going for it too.
It would not be the end of another year without another Airgun, Airsoft Gun and Blank Gun Collection video for you. This year I'm not showing all my guns, I started to take them out and quickly realized there where just way too many and this years video would have been several hours long and would have taken most of the week for me to shoot and edit...
So this year I have hand picked some of my top favorites and most notable replica Airgun, Airsoft Gun and Blank Guns. They may not all be the best made or hardest shooters or even all that accurate but each one has some significants to me.
Trigger Pull: The trigger pull on the Umarex HK G36 KVis fairly short and light as it is essentially just an electrical on off switch for the internal electronic components. You can shoot the G36 very quickly in semi auto mode, and in full auto it cycles very quickly giving a high rate of fire.
Accuracy: In my brief pre-testing without any sighting in, the Umarex Heckler & Koch G36 KV shot just a bit off center to the right from a 30 foot semi rested position and produced a nice 2 inch grouping. In full auto the grouping opened up a bit but still punched a nice 1.5 inch hole in the target with most of the BB hitting there.
Build Quality: The Umarex HK G36 KV is very well made, yes it has lots of polymer but so does the real version and the plastic seems very durable, the fit and finish looked great and there is a lot of metal in and around the G36 where it would be on the real steel gun and where it is really required to be. Like the trigger, top rail, pins, selector switch, barrel, gearbox and gears.
Realism: Similar to my WE G39C reviewed earlier, I bet if you had a real Heckler & Koch G36 sitting beside the Umarex HK G36 KV, you would be hard pressed to tell them apart? The Umarex is also fully HK licensed and trademark throughout even including the 5.56mm NATO markings.
Excellent attention to detail with lots of working parts.
All metal internals and metal external mechanical parts.
Semi auto & full auto selectable.
Full HK licensing and markings.
Accurate 2 inch 10 shot group from 30 feet out.
Nice high 450+ FPS.
Full ambidextrous, even the charging handle can be switched side to side.
High capacity magazine (400 rounds)
Built in 3x optical sight with ability to add a Red Dot for close quarter shooting.
4 position adjustable folding stock.
Easy access to hop up system.
Cons:
Does not come with a battery or charger.
Came with the orange tip, you may want to replace it or paint it black?
May be too powerful for close quarter skirmishes without some detuning.
Comments:
This is my first Umarex Airsoft rifle product review and I have to say it really seems good so far, I have not had a lot of hands on time shooting the Umarex HK G36 KV but right out of the box I was getting very good results, nice high 450+ fps and good groupings even out at further range. The fit and finish are all very good and the realism is as good, if not better than other Airsoft AEG I have reviewed. I like the built in 3x Optical Scope and the addition of an upper rail to accommodate a Red Dot, this gives you the ability to acquire quick close up shot placements using a Red Dot while also being able to focus in on further out targets using the magnified optical scope. I look forward to my official Field Test shooting review.
Materials: Mostly metal construction with a few plastic parts.
Weight: 2.1 pounds.
Barrel: 4.88 inches, metal non-rifled.
Propulsion: CO2 x 1.
Action: Semi auto blowback, single action only.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 16 round magazine.
FPS: 400+.
Trigger Pull: The trigger pull on the G&G Xtreme 45 is very smooth in single action only mode with there being just a bit of take-up and then a fairly light release, the light blowback and single action trigger allow fast sequential shooting with good groupings.
Accuracy: This is somewhat yet to be determined in my upcoming Field Test Shooting portion of this review but I did get the chance to take it outside and put some rounds down range, performance overall seemed decent.
Build Quality: This is an almost all metal air gun with good fit and finish and a nice hefty 2.1 pound weight to it. very similar in build to the Umarex Colt Special Combat 4.5mm BB Pistol reviewed earlier! The only plastic parts to speak of are the grips. In a perfect world, real wood grips would be nice but I have feeling that real 1911 grips may just fit this gun?
Realism: The G&G Xtreme 45 is a very good replica of the classic 45 auto 1911 styled pistol, with the exception of the trigger mechanism. I was happy to see if had a single action only trigger like you would find in a 1911 so this was a bonus. Overall weigh and feel make this Airsoft pistol a very believable gun and the blowback although light gives some nice feedback when shooting and the allowable single action trigger on followup shot.
Blowback operation (enough to give it some shot feedback and also cocks the hammer for easy single action trigger pull).
High fps for a blowback Airsoft pistol.
Expect to get decent amount of shots per CO2.
Fully adjustable rear sight.
Attractive two tone finish.
Magazine is all metal full size and hold both the CO2 and BB's and has a flush hidden CO2 screw.
Rain for accessories.
Very affordable gun considering all of the features it comes with.
Cons:
Blowback operation is light and not a full cycle.
Slide catch does not engage on the last round.
Does not have a true 1911 styled trigger but at least is single action.
Comments:
The G&G Xtreme 45 CO2 Blowback Airsoft Pistol is a great combination of realism and practicality toped with lots of great features you don't often find in a gun in this price range: Almost all metal, blowback operation, good fps and CO2 usage, fully adjustable rear sight, full size drop out metal magazine with hidden tab, awesome looks, and low price point. If your in the market for a good all around 1911 styled Airsoft blowback pistol, definitely put this one on the check list!
My Vimeo Video Review for the G&G Xtreme 45 CO2 Blowback Airsoft Pistol:
This Update video addresses the similarities between the KWC and Cybergun product lines, specifically the KWC Model 1911 vs. the Cybergun Tanfoglio Witness 1911 and the KWC Taurus PT99 vs. the Cybergun GSG 92. In a nutshell, they are all made by KWC and are exactly the same with the exception of some of the licensing and branding that goes on the slides. Cybergun simply contracts KWC to make the guns for them and add some slight different printing. All parts are interchangeable.
I also show you the Silver Finish Blowback Airsoft KWC Desert Eagle and mention again that the licensing on this one is kind of hit and miss depending on what KWC sends us. So when you order one there is an additional surprise waiting for you when you open the box :)
Lastly, I show for the first time a G&G Airsoft product, the G&G Xtreme 45 Blowback that looks an awful lot like the Umarex Colt Special Combat chambered in 4.5mm Steel BB. The main differences are that the Colt Special Combat is a BB gun and the Xtreme 45 is an Airsoft gun. The G&G has blowback where as the Colt Special Combat does not have blowback.
Make sure to checkout my Vimeo video of this product update for even more info!
A bit of a heads up, one of our most poplar BB and Airsoft Pistols, the Dan Wesson line is for the most part fairly well stocked right now in the Canada Replica Airguns Store and ready for the Christmas rush! With that said don't hold off too long because we always run out of at least a few of the most popular versions...
Trigger Pull: The trigger pull on the Bolt Airsoft B4A1 is fairly short and light as it is essentially just an on off switch for the internal electronic components. You can shoot this gun very quickly in semi auto mode, and of course in full auto when full auto position is selected. As is with all AEG rifles there is a bit of a delay while the spring is retracted and released, this is not as noticeable in full auto.
Accuracy: I tested the B4A1 Airsoft rifle by putting around 10 rounds into a target from 30 feet with .36 gram Airsoft 6mm BB's while using a semi rested position (sand bag in the front - standing in the rear). I used a non-magnified red dot scope for this test rather than using the built in iron sights. I got very good result in semi auto and even with the recoil making my sights jump around a bit in full auto still stayed well centered on target and got about a 1.5 inch group in both semi and full auto. My chronograph testing with lighter .20 gram BB's resulted in a 421 fps 5 shot average.
Build Quality: The Bolt Airsoft B4A1 Metal AEG Carbine is very well made with a full Metal upper and lower receiver, along with metal and polymer parts exactly where they would be on the real steel version of an actual Colt M4. The only plastic or nylon components are the stocks and the grips and perhaps some internal parts. I found the adjustable stock and magazine tolerance to be tighter than my King Arms M4A1 I previously reviewed which showed the Bolt B4A1 had a bit higher quality in the workmanship, for the most part the fit and finish was very good!
Realism: As with many Airsoft guns, there is great attention to realism and the Bolt Airsoft BRSS B4A1 Carbine is another great example of an Airsoft Carbine based on the Colt M4 platform. It is an AEG but because of the BRSS (Bolt Recoil Shock System) you get a very nice compromise between a conventional AEG and a GBB (Gas Blow Back Airsoft) gun. In other words, like a standard AEG I get that endless stream of consistent BB's flying down range on target but unlike a true Gas Blow Back Airsoft gun, I don't get that drop off in power and limitation to about 30 usable rounds per magazine . What I do get similar to a GBB is that recoil action that helps make the shooting experience so much more believable! Even the sound from the Bolt B4A1 is much snapper than a standard AEG and more like a GBB. I also like the fact that the charging handle and forward assist work similarly to a real M4 and also the dust cover cleverly exposes the bolt and internal hop-up for easy adjustment along with the bolt cycling just like a GBB rifle would cycle which is similar to a real steel M4.
Great attention to detail with lots of working parts.
All Metal upper and lower receiver, lots of metal parts throughout.
Semi auto & full auto selectable.
High capacity 300+ round magazine.
Removable carry handle with Weaver/Picatinny rail underneath.
Nice high 420 real FPS.
Extremely accurate for plastic BB's.
Fully adjustable sights with two position Peep sights.
6 position adjustable stock.
Easy access to internal hop-up system.
Realistic Blowback Recoil system (BRSS) for a very believable shooting experience!
Cons:
May not get off as many shots per battery charge as a traditional AEG because of the Bolt Recoil Shock System.
Does not come with battery or charger but most higher end AEG's also do not.
Not yet readily available in Canada, maybe we can change that :)
Comments:
The Bolt Airsoft B4A1 Blowback Airsoft Carbine is a great compromise for the avid Airsofter looking for a practical skirmish weapon, but also craving the realistic experience of having blowback with recoil which up until now was really only provided by Gas Blow Back systems. I really like this concept and find it great fun to shoot even if its just for plinking in the yard. The overall quality is very good and you just have to love the M4 platform it's based on. If you're into customizing you can mix and match many external and internal parts with other existing Airsoft mechanical parts and I would imagine real steel accessories. I like mine as is with my addition of a riser and Red Dot and if I every get a chance to get out for a skirmish this will be my weapon of choice for sure!
I got a few sample products I wanted to quickly share with everyone :) First off Bolt Airsoft, a Taiwanese based company, sent me one of their B4A1 (M4A1 Copy) AEG Airsoft rifles featuring BRSS - (Bolt Recoil Shock System) which has Blowback with simulated recoil.
The Bolt B4A1 is designed after the M4A1 and looks and works like most AEG Airsoft rifles giving you sustained performance and the use of high capacity magazines but Bolt has added their BRSS - (Bolt Recoil Shock System) which gives you the feedback and recoil you would normally only get with a true GBB (Gas Blow Back) Airsoft gun.
I will be doing a full review very shortly so watch for it!
I also received from ASG (Action Sport Games) a few Mock Airsoft Suppressors, all of them are B&T (Brügger & Thomet) derivatives. It was nice that they sent me the version (MP9 QD) that fits perfectly on my ASG/KWA MP9. The other tow are the ROTEX-IIIA and ROTEX-IIIA Compact that fit perfectly on to a standard flash hider and even include one with them.
Check out my Vimeo Preview Video of these Review items from Bolt Airsoft and ASG:
Trigger Pull: The trigger pull on the ASG/KWC MP9 A3 is single action only as the charging handle has to be pulled back to open and release the bolt for the first shot. There is a trigger safety but it is not noticeable when shooting this Airsoft machine gun. There is a short take-up and then a light release and short reset.
Accuracy: Right away I put my NcSTAR 1x25 Red Dot sight on the ASG/KWC MP9 A3 as it was a perfect fit for this small and compact machine pistol, it did not take long to sight it in and I was able to get decent accuracy in both semi auto and full auto burst due to the mild but very fast cycle rate. I was able to get a 2 inch grouping at 30 feet out using a rested position. In full auto mode the grouping did not really get too much wider. I also got between 350 and 370 fps when testing the ASG MP9 on my Chronograph.
Build Quality: The ASG/KWC MP9 A3 Airsoft Machine Pistol is built very well, using similar components that you would find on the real steel version so yes it has a plastic shell but that is to be expected. The ASG/KWC MP9 A3 does use lots of metal where it needs to be like in the internal parts, pins, bolt, barrel, rails and even the magazine. The fit and finish is near perfect!
Realism: I have to say the ASG/KWC MP9 A3 is pretty much a bang on copy of the real steel Brügger & Thomet MP9 A3. The only telltale sign is the ASG branding on the right side along with the 6mm caliber beside the ASG logo. One other small detail is the magazine which is metal on the Airsoft version where as you would find the real version uses a transparent polymer magazine.
Rate of fire is very fast and does not slow down much even when the gas is running low.
Good overall power for a short barreled gas blowback gun.
Very nice trigger with working trigger safety.
Excellent replica of the real steel version in just about every way.
Can add a lot of gear and make this gun your own.
Decent price for all you get out of the ASG MP9!
Cons:
Bolt didn't lock back for me when the gun got really cold?
Real magazine would actually be transparent polymer.
Comments:
I really like the ASG/KWC MP9 A3! I love the look, I love the features and the price is also really good for what you are getting. I was really impressed with the super high cycle rate and because of the small low weight bolt the gun does not move around too much or slow down in rounds per minute even when you do a full mag dump. There is however just enough blowback recoil to give you that GBB realistic feel! I also found that the magazine holds a lot of gas so it is possible to get two magazine worth of shots out of a single fill, that's around 100 shots. I also like how easy it is to add to the ASG/KWC MP9 A3, I had mine pimped out and looking amazing right away and suggest if you get one you do the same :)
My Vimeo Video of the ASG/KWC MP9 A3 Airsoft Machine Pistol:
