View fullsize

Airguns are not toys and as so require proper storage, transportation and handling so as not to cause an accident that could be minor or even deadly.

No matter if you are handling an Airgun or a “Real Gun”, they should both be handled in the same manner even if the consequences from an accident with an Airgun may be less serious. Life long injuries like the loss of an eye are nothing to be taken lightly.

For the most part, what I talk about in this Airgun Safety 101 video can also be applied to a “Real Gun” although most countries will have stricter laws and guidelines in the storage, transportation and handling of “Real Guns” over an Airgun.

View fullsize

Storing Your Airgun:

In Canada an unregulated Airgun does not have any real specific safe storage guidelines but common sense should be used and I recommend that you at the bare minimum keep your Airgun in some sort of locked space whether it be a safe, cabinet or room that is locked all of the time.

You can also put a trigger lock on your Airgun if you do not have a lockable storage location for it.

You should also make sure to store your Airgun unloaded, at least when it comes to BB’s and or Pellets. If there is some unused CO2 in it, or it is charged with Compressed Air, but unloaded in terms of ammunition, that is OK, but again keep it in a safe location away from anyone that may be able to get their hands on it and hurt themselves or others.

View fullsize

Transporting Your Airgun:

Again, in Canada an unregulated Airgun does not have any real transportation guidelines but if you keep your Airgun out in the open and someone sees it, they will most certainly call the police and more than likely you may find yourself staring down the wrong end of a police firearm, at least until they sort it all out. This is very serious as unfortunately people have died as a result of handling their Airguns out in the open and underestimating what kind of police response that may entail.

For that reason alone, always keep your Airgun out of sight in a case or backpack or the trunk of your car. Never transport your Airgun loaded and it is best if you can lock it in a case or put a trigger lock on it for added safety when transporting it.

View fullsize

Shooting Your Airgun:

Shooting your Airgun is always the most enjoyable part of owning an Airgun, so don’t do something stupid and turn that experience into a nightmare. Treat your Airgun as if it is deadly at all times, never point it at anything you do not intend on shooting.

Keep your safety on until you are ready to shoot. Never put your finger on the trigger until you are ready to shoot it and only shoot it in a safe location with an appropriate background and backstop.

Think of the barrel of your Airgun as a light saber that if it crosses even your arm, it could cut it off. Even a BB to the arm is a serious matter. I had a friend that shot himself in the arm with a BB Gun and the BB lodged in the tendons of his wrist requiring an operation to remove it. He was a violin player so this could have ended his violin playing, but luckily he was OK.

When Your finger is not on the trigger it should be held across the trigger guard in a straight position to ensure no accidental misfires.

Wear eye protection, Steel BB’s will bounce back when they hit a hard surface and can come back with enough force to injure an eye easily. Generally Airguns do not require ear protection but some can be loud enough that you may want to wear some sort of ear protection as a precaution.

Only shoot with others that are responsible and take Gun Safety very seriously. Young people will need constant supervision and it is best to go through all of this first before even considering handing them an Airgun for the first time. Perhaps start them off with something like an Airsoft gun which will have less consequences if an accident were to take place.

Airguns are awesome in so many ways and allow for a similar shooting experience to a “Real Gun”. They can be used in more situations, with less overall cost and are a great way to learn proper gun handling and how to improve your shooting ability even if you are a “Real Gun” owner. Always be responsible with your Airgun not only for yourself but for others as it only takes a few idiots to ruin things for the rest of us. Don’t be that Idiot please!

• Buy Airguns in Canada

• Buy Airguns in the US

There are many types of magazines used in Airguns and some of this is dependent on the ammunition used.

For instance a stacked type of magazine often used for Steel BB and Airsoft can not be used for Pellets as pellets tend to deform when stacked in such a way since there is no metal casting protecting them from mashing into each other.

So what type of magazines do we generally see in Airguns? The most common Airgun magazines are as follows:

Simple Stick Magazine

• Mostly used with Steel BB but also found in some Airsoft Airguns.

• Some Pellet Airguns use a type of stick magazine with a rotary magazine on each end.

• Used in non-blowback and blowback Airguns.

• Can be made from plastic or steel or a combination of both materials.

Full Size Drop Out Magazine

• Used with Steel BB and Airsoft guns.

• Generally you will find these types magazines hold both the BB’s and CO2.

• Used in non-blowback and blowback Airguns.

• Commonly used with Airsoft Rifles in mid to high capacity.

• Can be made from plastic or steel or a combination of both materials.

Rotary magazine

• Used with Steel BB, Airsoft and Pellet Airguns.

• Used in non-blowback and blowback Airguns.

• Can be made from plastic or steel.

• Can often use mixed ammo types as in both 4.5mm Steel BB and .177 caliber pellet.

Belt Fed Magazine

• Like rotary magazine belt fed magazine can accommodate Steel BB, Pellet and Airsoft but are most often used with Pellet Airguns.

• Usually found in a full size magazine that also holds the CO2.

• Used in non-blowback and blowback Airguns.

• Can be made from plastic or steel or a combination of both materials.

Internal Magazine

• Used with Steel BB, Airsoft.

• Can have a hopper built in hat feeds a spring fed magazine.

• Usually found in lesser expensive Airguns but not a rule.

In this Video I go through each type of Airgun Magazine and talk about their differences and uses.

View fullsize

There has been some confusion when it comes to the KWC made Mini UZI regarding semi and full auto abilities and also when it comes to build materials. But before we get into that if you have one of these Mini UZI Blowback BB or Airsoft guns then most likely yours is made by KWC even if it was distributed through RWS, Umarex, Gletcher, Cybergun or some other company. When it comes to the build materials used they are all made by KWC so they are all built the same with plastic and metal in the same places.

View fullsize

Let’s first talk about why some of these Mini UZI’s only come in semi auto with the Full auto selection not available out of the box. This is most likely because in some countries a full auto BB and/or Airsoft gun can be illegal so to play it safe many airguns that are originally made to shoot in both semi and full auto are modified to only shoot full auto. This is the case with most of the companies that redistribute the KWC Mini UZI under their own brand name. That said if you buy the KWC Mini UZI in either 4.5.mm Steel BB or 6mm Plastic Airsoft from our Replica Airguns Canada or US Online Stores, you will be getting a full auto ready out of the box airgun!

If your MINI UZI Airgun is not full auto ready then checkout my Full Auto Mod Video but make sure before you do this modification it is legal in your country to do so or you could be looking at jail time :(

View fullsize

When it comes to build materials the KWC Mini UZI is often described on websites as being full metal which is close but not entirely true. It is accepted that most full metal airguns will have plastic grips but the KWC Mini UZI also has a plastic shroud around the main receiver that is am all in one piece that makes o=up the front and back sights. This might lead you to think that the gun is mainly plastic which is far from the case since all other parts like the receiver block, bolt, top plate, barrel, rear stock, trigger and magazine are metal. This give the KWC Mini UZI its sold 4.8 pound weight. The heavy metal internal bolt really makes this blowback airgun rock when you shoot it simulating very close recoil action to a 22LR. The KWC Mini UZI for sure has the most blowback recoil out there.

View fullsize

If you are looking for the most bad ass and action packed full auto BB or Airsoft Gun then I would highly suggest you consider getting one of these KWC Mini UZI’s. Just be sure to have lots of CO2 and BB’s on hand because you will go through both like crazy…

• Buy the KWC Mini UZI BB Gun in Canada

• Buy the KWC Mini UZI Airsoft Gun in Canada

• Buy the KWC Mini UZI BB Gun in the US

• Buy the KWC Mini UZI Airsoft Gun in the US

I made a similar video about how to hold your airgun a while back but sometimes they get a bit buried in all the video I make. I feel it's really important how you grip your gun even if it's only an airgun with very little kick or recoil. Proper pistol grip is something you should use no matter what so that you can carry it forward to what ever gun you are shooting.

More kick or recoil means a firmer grip is required to hold the gun so when shooting a powder burner with lots of kick grip becomes even more important.

In this video I go over the proper two handed grip to use when holding a pistol, which hand to hold lose and which had to grip tight, how to overlap your fingers and thumbs.

View fullsize

I usually do my Table Top Video Review first but in this case I decided to pump out my Field Test Shooting video ahead of it. So if you're looking for more detailed specifications then just wait a bit till I get my Table Top Review out. What you really need to know about the Umarex Morph 3X CO2 BB Gun is that it's a CO2 4.5mm BB Gun with a 30 round internal magazine sporting multiple configurations as the stock, barrel and forward stock are all removable so it can be a pistol or a rifle and many variations in-between, even more than 3X of them.

View fullsize

The US version of the Morph 3X CO2 BB Gun when installing the rifled barrel (Which is not rifled buy the way), will shoot faster than when the Morph 3X CO2 BB Gun is in pistol version since the add on barrel adds a lot of additional barrel length to the airgun. The Canadian version which I am testing does come with the extension rifle barrel but it is only for show as the inside is missing the 4.5mm inner barrel. This is because our Canadian import laws for uncontrolled firearms would not allow the rifle version of the Morph 3X CO2 BB Gun here in Canada as it would potentially shoot with too much fps (around 600 fps) and foot pounds of energy for our Canadian non regulated gun laws. As it stand the Canadian version of the Morph 3X CO2 BB Gun has an fps rating of 480 fps in both pistol and rifle configurations.

View fullsize

All that aside how did the Morph 3X CO2 BB Gun do during my testing? Awesome to be precise! It actually averaged a 5 shot Chronograph Velocity Test of 498 fps even in pistol configuration which is very impressive for a CO 2 BB gun. I also was able to get the majority of my 10 shots on a paper target positioned 30 feet away from me using a rested seated position within about 3/4 of an inch. I even played around a bit with holding the Morph 3X CO2 BB Gun out in front like a pistol and tight to my shoulder using the rear stock.

View fullsize

It's kind of too bad we don't have the inner rifled version here in Canada as even at 600 fps we are just under 4.2 foot pound Canadian limit but trying to explain that this is still OK to our CBSA border guards is just a little too much for them to process :) Even without the inner barrel the Morph 3X CO2 BB Gun is a really great and super versitile airgun with lots of power and just as good accuracy!

Buy Umarex MORPH 3X CO2 Carbine in Canada 
Buy Umarex MORPH 3X CO2 Carbine in the US

One of the most common types of question I get on my Replica Airguns YouTube channel has to be something like… Why is my Airgun not working? Most of the time the amount of info about the problem is limited to something like… “It was working yesterday but now it’s not working anymore” or something like “when I pull the trigger nothing happens”. My personal favorite is… “I took my gun apart and now it doesn’t work!”

I just made a similar video for Blank Guns and as I said in that video, trying to trouble shoot a mechanical or technical problem over the internet is very difficult, this goes for cars, guns, computers or what have you…

In this Why is My CO2 Airgun Not Working video I will however cover some of the more common and obvious problems I have seen relating to why a CO2 Airgun may not be working properly. I really don’t get a lot of questions about Spring Piston or Pump Airguns so I will be focusing on CO2 Airguns in this video. There will be a lot of crossover with CO2 Airsoft guns so this video may be helpful for some of you Airsofters out there

First let’s get the super obvious stuff out of the way! 

• Did you put a new CO2 cartridge in it and is it pierced all the way?

• Did you load BB’s or Pellets into the Airguns magazine and is the magazine in the gun correctly?

• Is the safety off?

• If the gun is a blowback semi auto single action Airgun then did you pull the slide back prior to the first shot?

CO2 Related Problems:

Not all CO2 cartridges are created equal, they often have slightly different shaped nubs on them and some brands will work better than others in different Airguns. If the shape of the CO2 nub does not fit properly into the valve area then it may not pierce or it could pierce but then not allow you to tighten it all the way losing all the CO2 in the process. If the CO2 is coming form the airguns handle to CO2 Valve area then this is an indication that your problem is related to the area where the CO2 enters the airgun.

There is a seal where the CO2 cartridge buts up to the valve, this seal can be damaged or even deformed from usage or even leaving your CO2 in the gun for too long. The outside CO2 Valve seal can also take the shape of a specific CO2 nub so when you use a different brand CO2 the seal may not properly make concat with the new CO2 type you are using, again causing leaking or even the total loss of all your CO2. Watch my YouTube video on “How to Fix Leaking CO2 in an Airgun”.

CO2 Valve Related Problems:

Again, make sure that Outside CO2 Valve Seal is in good condition and any leaking is not being caused by this problem, if you have checked the Out Side Seal and everything is OK with it then perhaps there is a problem with the CO2 valve?

One indication that your CO2 Valve might be the culprit is the total loss of all your CO2 when you try to insert and tighten a new CO2 Cartridge. Usually all the CO2 will exit the barrel, not the handle or valve area. What may be happening is the valve is stuck open or the internal seal is broken or deformed. If this is the case you will have to remove the valve and have a look inside, this is a lot easier on CO2 airguns that have the CO2 valve in the magazine, if the CO2 valve is in the actual Airguns then a lot more disassembly may be required and I would recommend an Airgun technician take care of this for you.

If the gavel is in the magazine then you will have to unscrew it, you may require a special tool for this? Once the valve is out of the magazine  take a look inside and examine the internal seal, also look for any bits of metal shavings as they can disrupt the action of the valve causing leaking. Give the inside of the valve a good clean and then lubricate it with some silence spray. hopefully that fixes your problem!

BB’s getting Stuck in the Blowback Gas Tube:

I have actually made a dedicated video for this problem so I will put a link to it in the description of this video. The main reason people may have this problem is because we all like to rack that slide on our full blowback Airguns, but if you have a fully loaded magazine then each time you reach that slide without shooting the gun, you are inadvertently trying to load another BB into the breach area, the breach is only designed to hold one BB at a time so after a few racks of the slide the newly loaded have no place to go but into the Gas Tube where they can get stuck and cause having to the operation of your Full Blowback CO2 Airgun.

BB’s Rolling Out of the Barrel of Your CO2 Airgun:

This is not actually a fault of the gun but happens because of the way the gun is designed. This situation can happen with certain CO2 Airguns when the gun user pulls the trigger really slowly while the gun is point slightly in a downward position. What is actually happening is the first part of the trigger is made to draw a BB from the magazine into the breach of the gun. If the barrel of the gun does not have a rubber hop-up stopper in it then the BB is free to roll down the barrel and out of the gun. How do you fix this problem? Be more committed to your trigger pull and or shoot at a target that is not so low. Perhaps place your targets slightly higher than the gun so the barrel is not pointing down, especially if you like to take your time with the trigger :)

A Little Maintenance Can Go a Long Way!

Sometimes a good cleans is all you need to do to get things working as they should, again I have already made video Tutorial Showing “How to Clean Airguns and Blank Guns”.

What about stuff like My Airgun is jammed or my trigger is stuck or some random part fell out of my gun?

There is only so much I can cover in this video, most other problems are going to get a bit more complicated to fix and I suggest if your Airgun is not working and the suggestions I have made in this video do not solve your problem, then consider taking your gun into a gun tech.

First off I want to say it’s hard to trouble shoot technical or mechanical problems over the internet regardless of if ithas to do with guns, cars, computers or pretty much anything where unless you are there in person it’s really hard to figure out the problem.

But I will attempt to address some of the more common issues why a blank gun may not be functioning properly.

Why is my Semi Auto Blank Gun Not Cycling or Ejecting Shells?

One very common reason a blank gun may not be cycling the shells properly is because the owner has removed the barrel restrictor plug. People usually do this to make the barrel opening look more realistic but the barrel restrictor is a necessary component to increase the back pressure allowing the slide to cycle fully to the rear position so it can eject and pickup a new shell.

The blanks you are using may not have enough gun powder in them. Some blank guns require banks with more gun powder than others, again this additional internal pressure forces the slide all the way back, if the blank does not have enough gun powder in it then only a partial slide motion happens and so the discharged shell may not eject properly, in this case the user would have to clear the blank gun manually so another shell can then be picked up and loaded into the breach.

If your blank guns is dirty or not lubricated then it may act sluggish again restricting the full movement of the slide which will effect correct operation. Make sure to thoroughly clean and lubricate your blank gun, that may be a quick fix for you!

You may have a faulty extractor? The extractor is like a hook that grabs the discharged shell while the slide is in the reward position pulling or extracting the shell out of the breach. If the extractor is worn or broken then the empty shell will not be ejected from the breach so when a new shell is picked up from the magazine it has nowhere to go and usually you will get a jam-up in the ejection port area.

One final situation that can cause your blank gun to not cycle properly is to strong of a slide spring, some blank guns out of the box just come with a really heavy slide spring, so much so that even blanks with lots of gunpowder in them are still not strong enough to make the slide operate full motion. Your only option here would be to replace the heavy slide spring with a lighter one.

Why Are My Blanks Not Firing?

This is a situation where you pull the trigger and nothing happens. Lets get the obvious causes right out of the way here… Did you put blanks in your gun and are they new blanks? Did you chamber the first round in your semi auto pistol?

So now that that’s out of the way let’s look at some other reasons why your blank gun may not be firing a blank. Perhaps the firing pin is broken? Most blank guns are not made out of carbon steel and even the firing pins can be lesser quality than what you would find in a real gun so blank guns are more prone to breaking than real guns. I have seen broken firing pins in blank guns first hand so make sure to check the firing pin and that it is fully operational.

Try changing up your blanks to another brand? Again blank gun ammunition is not made to the same higher standards that real firearm ammo is made and some primers may require a little more pressure than your gun is providing. Even with real guns an ammo change may help the gun operate better.

Why is the Trigger or Hammer Not Operating Properly?

I have come across blank guns where there are mechanical problems in the trigger and hammer areas, you may be able to address this yourself but I would recommend taking your blank gun to a gunsmith since you will have to take the gun pretty much full apart to fix a problem in the trigger and hammer areas.

Of course make sure your gun is clean and lubricated, this can help a lot with the mechanical areas of your blank gun.

One problem I saw with a few EKOL Special 99’s was specifically with the single action potion of the trigger, when I would pull the hammer back it would not lock back and the hammer would often slip and fire randomly, this is rather dangerous. When I took the gun apart I found that the table top or step that the trigger was supposed to catch on was worn down on the edge so it would simply slip off. I was able to fix this by filing a new edge on the step area. Again this can happen because blank guns are not made out of as high quality metal materials as real guns.

Why does the Flame Come out the Top of My Blank Gun and Not the Front?

If you find that the flame or discharge comes out of the top of your blank gun and not the barrel, this usually does not mean anything is wrong with your blank gun. All it means is you own a top venting blank gun and not a front firing blank gun. In some countries front firing blank guns are not allowed but front venting blank guns are. The same may also be reversed in some countries, for instance here in Canada we can only import front firing blank guns with flare adaptors since our blank guns are imported under the assumption that they are to be used as signaling or flare devices.

Can I Convert my Top Venting Blank Gun into a Front Venting Blank Gun?

I really don't recommend altering a blank gun in any way as it may be a violation of your local laws and it could cause the blank gun to malfunction in a very bad way causing serious injury or even death!

In theory I suppose it may be possible to convert your Top Venting Blank Gun into a Front Venting Blank Gun but again you would need to allow for just the right amount of back pressure so a wide open barrel would not work unless it was a revolver. You can not simply remove the red plug and bingo you have a front firing blank gun because in most cases the barrel will be completely plugged in the frontal region. Not only would you need to drill out the plugged portion of the barrel but you would also have to somehow fill in the top venting area and again makes sure to allow for just enough back pressure to cycle the slide back and forth.

Hopefully this has helped some of you with blank gun issues. If you’re looking for a blank gun make sure to come down to www.ReplicaAirguns.ca and www.ReplicaAirguns.us and have a look in our blank gun area of our online stores.

I already made several review videos for both Gletcher NGT (4.5mm Steel BB) and the Gletcher NGT R (.177 Cal Pellet) Revolvers, including table top and shooting videos. So make sure to check those videos out for more information on both versions of Gletcher NGT and NGT R Revolvers.

I did however miss some noteworthy details that I wanted to cover in this video. Firstly, the real steal Nagant M1895 Revolver this Gletcher NGT is styled after has a very unique gas-sealing system that the Airgun version does not replicate or really require but it is worth mentioning.

Here is some more info on how the original Nagant M1895 Revolver Gas Seal System works:

(From Wikipedia) The M1895 by contrast, has a mechanism which, as the hammer is cocked, first turns the cylinder and then moves it forward, closing the gap between the cylinder and the barrel. The cartridge, also unique, plays an important part in sealing the gun to the escape of propellant gases. The bullet is deeply seated, entirely within the cartridge case, and the case is slightly reduced in diameter at its mouth. The barrel features a short conical section at its rear; this accepts the mouth of the cartridge, completing the gas seal. By sealing the gap, the velocity of the bullet is increased by 15 to 45 m/s (50 to 150 ft/s.) This feature also eliminates the possibility of injury through the dangerous expansion of gases from the cylinder behind the barrel, which are easily capable of severing a finger if the user holds the gun incorrectly (with a finger positioned in front of the cylinder during fire) - a noted safety-issue in conventional revolvers.

Moving on to some of the features incorporated into the Gletcher NGT NGT-R CO2 BB and Pellet Revolver that I did not point in any of my previous videos. There is an extractor rod that can be used to extract a shell, this is not really necessary on the airgun version since the shells do not expand and tighten on the cylinder as they would n the real steal Nagant M1895 Revolver built is nice that we can replicate this feature with the Airgun version. You can also remove the cylinder completely from both the BB and Pellet shooting Gletcher NGT NGT-R CO2 Revolvers. The cylinder is actually very heavy and adds a lot of weight to this compact 7 shot Revolver.

It is always nice when an Airgun is built in such a way that it replicates the real steal version as closely as possible and the Gletcher NGT NGT-R CO2 BB and Pellet Revolvers do this nearly perfectly.

Buy Gletcher NGT Revolvers in Canada

Buy Gletcher NGT Revolvers in the US

I get asked on a daily bases form many of my Vimeo Viewers about how and if there is a way to get rid of the White lettering on Airguns, Typically people are wanting to remove the intrusive Warning instructions from Airguns like the Cybergun Tanfoglio Witness 1911, the Cybergun/Swiss Arms GSG 92/P92 and many other CO2 Replica Airguns that have lettering or branding that you may want to get rid of.

In this Instructional Tutorial Video I show you how can at least tone down the white lettering and even completely remove it on some Airguns without damaging the Airguns finish underneath the white lettering. You will have to use some patience and perhaps repeat this method a few times but the end result is worth the effort.

The magical product I use to remove the white lettering on many popular Airguns is a product from Birchwood Casey called the Presto Gun Blue Pen. This product is actually designed to touch up real steel gun in areas where the blueing has worn off, lucky for us the Birchwood Casey Presto Gun Blue Pen also works well to remove the ugly white lettering from Airguns.

I have often been asked which of the Shells for the Shell Loading Revolvers work in which Shell Loading Revolvers? After all many of them look a lot alike so can you mix and match Shells for the various types of Shell Loading Revolvers?

In this Vimeo Instructional Video I test out a bunch of Shells to see which ones actually will work or not work in several of the most popular Shell Loading Revolvers.

Some of the Shell Loading Revovers Tested in this Instructional Video are:

• Dan Wesson Classic Revolver (BB, Airsoft, Pellet)

• Dan Wesson 715 Revolver (BB, Airsoft, Pellet)

• Colt Single Action Army Peacemaker (BB, Airsoft, Pellet)

• Gletcher NGT and NGT-R (BB and Pellet)

• Webley Mark VI (BB)

• KWC 357 / Umarex 357 (BB, Airsoft)

• G&G G731 (Airsoft) 

I reviewed the Original ANT (Advanced Novelty Tech) CO2 HPA Conversion Kit last year and did both a Table Top Review and Field Test Shooting Review, so make sure to check out my video reviews for the Original ANT Advanced Novelty Tech CO2 HPA Conversion Kit.

Well ANT (Advanced Novelty Tech) made an update model that supports a bunch more guns, that's a good thing of course. This new model is called the "FIRE" and it supports the following guns. I did find however that ANT list that the Gletcher NGT and Webley Mark VI Revolvers where supported by the FIRE but my findings indicated the CO2 screw on both these guns had a smaller diameter so they where not compatible. Other than that small discrepancy most of the other guns on their list should work just fine.

What exactly is the ANT Advanced Novelty Tech FIRE CO2 HPA Conversion Kit?

The Advanced Novelty Tech FIRE CO2/HPA Conversion Kit is a remote line adapter for Airsoft, BB, and pellet guns. Compatible with over 60 guns, it is easy to install and converts a compatible gun for use with a Paintball remote line and CO2 or HPA tank. Eliminating the need for disposable CO2 cartridges, while still being interchangeable with disposable CO2 cartridges, it delivers a longer, more powerful, and more consistent shooting experience between refills.

So what is the ANT Advanced Novelty Tech FIRE CO2 HPA Conversion Kit going to do for you?

• Eliminate the need for the more expensive disposable 12 gram CO2 cartridges.

• Use interchangeably with disposable 12 gram CO2 cartridges.

• Use in conjunction with a Paintball remote line with standard quick disconnect fittings and a CO2 or HPA tank. (recommended use up to 1000 psi)

• Shoot thousands of rounds before needing to refill your CO2.

• Fits compatible Airsoft, BB, and pellet gun CO2 pistols.

• Easy drop-in installation.

• Overall cost savings.

• More consistent FPS especially when shooting fast or in full auto.

• Longer play time :)

I will be doing a Field Test Shooting Review for the ANT Advanced Novelty Tech FIRE CO2 HPA Conversion Kit but based on my experience with the Original ANT CO2 HPA Conversion Kit I expect it to work as advertised.

I am showcasing here on the Replica Airguns website and over on the Replica Airguns YouTube channel a series of videos I am making for the purpose of selling some guns out of my personal collection. I simply have no more room for the new guns and in some cases I either have duplicate guns or very similar versions so there is no need to have both. Some guns I am less attached to and as I already stated I need to make room for some of the new stuff I will be reviewing and or buying for myself.

In this third Mike's Personal Guns For Sale video I am offering four BB rifles, three of which have full auto or at least burst mode ability and the fourth BB rifles is more of a Shotguns with the ability to shoot three BB's at once. Most of these BB rifles are really hard to get here in Canada now since one is not made anymore and the two are simply not currently being imported into Canada.

Make sure to watch my above YouTube video to see these four BB rifles I am selling and instructions on how you can take part in the sale and purchase of them. By the way I am only selling to Canadian residents since shipping cross borders is a little sketchy.

Here is a list of the BB Rifles I am selling from my personal gun collection:

Custom Baikal Drozd Blackbird 4.5mm Steel BB Machine Gun $925

Umarex EBOS 4.5mm Steel BB Machine Gun $225

Umarex SG9000 4.5mm Steel BB Shotgun $175

Umarex Steel Storm 4.5mm Steel BB Gun $100

With the popularity of the KWC - Cybergun 1911 Blowback CO2 Pistols and how super realistic they are in so many ways, it is no surprise that people often ask me if they can replace the original grips with grips made for a real 1911.

The short answer is yes you can! You will have to be prepared to remove just a little bit of material from the backside of both grips near the bottom of the handle where there is an area that has been flared out to accommodate the CO2. Not really a big deal, you can use a Dremel for the quick and easy approach or even some sand paper if you don't mind taking a little more time.

In this Vimeo Video I demonstrate using grips that fit a real 1911 and show you just exactly where you will need modify them to fit on the KWC and Cybergun CO2 Blowback 1911 pistol series.

Buy the KWC Blowback CO2 1911 BB Pistol in Canada

Whether you like it or not, most of us have come across an Airgun with an ugly orange tip on it at some point. In most cases you will find the intrusive orange or red tips on Airsoft guns that shoot plastic BB's, in some cases you will even find them on Airguns that shoot either lead pellets and/or steel BB's.

It really comes down to where you live as to what your local gun laws have determined is required for your area. You may even live in a region where Airguns and Airsoft guns are not allowed at all! So for you a red or orange tip on the front would be welcome if it would allow you to own an Airgun or Airsoft gun. What about the entire gun being painted a bright color, well that is the case for some folks so again having a red or orange tips may not be as bad as it originally seemed...

In Canada where I live, we used to only be allowed Airsoft guns that had clear sections as our replica gun laws are very strict and all black Airsoft guns would have fallen iinto the "replica" category if they did not have large clear plastic see-through sections on them. This clear section law was revised somewhat over the last several years to allow for all black Airsoft guns here in Canada. It was determined that many Airsoft guns with higher fps limits could cause a serious injury to a human, making them less of a toy in the eyes of the law and more of a weapon. Because of this, Airsoft guns that are capable of shooting a .20 gram plastic BB at a velocity of 360 fps or "higher" are now considered to be similar in the eyes of the law to a regular steel BB or lead pellet shooting Airgun. In Canada, Pellet and Steel BB guns are actually considered firearms of a sort so this allows the higher fps Airsoft guns to be all black since it can not be a replica of a firearm if it is in fact considered to be a firearm by law.

The long and short of all of this is that here in Canada we do not require our Airsoft guns to have orange or red tips since they are considered more or less to be just like any other Airgun and our Airguns do not have red or orange tips either.

Getting back to the title of this article "No Orange Tip On Your Airsoft Gun! Are You Insane?" I often get folks from the US giving me heck for removing the orange tips from my Airsoft guns or asking me why my Airsoft guns don't have them in the first place. These people even state that I could get in a lot of trouble for this! Perhaps they think I live in the US or that US laws govern Canada as well? I am not sure but I can say for the record that I am not breaking any laws at least here in Canada where I live.

I know in the US that wholesalers and retailers by law have to sell Airsoft guns with the affixed orange tips on them, once the end user receives that gun and depending on which state they live in, it may or may not be legal to remove the orange tip. Again, you will need to look into your local state laws as they are different from state to state in the US.

While the weather is still nice, I decided to setup some clay pigeon targets at varying further out ranges than the typically 30 feet I shoot on my deck. So I figured 40-60-80-100 foot ranges would be a good test to see if a 4.5mm Steel BB rifle could effectively hit targets at any of these ranges.

I did do a similar test earlier on using my Umarex Steel Force but I think the Steel Force may have been a bit underpowered for the 80-100 foot shots.

So today I brought out my Drozd Blackbird since it has a bit of power and what it may lack in accuracy it for sure makes up in volume! As with many of my shooting videos I captured all the fun using a bunch of different cameras and camera angles and today I even wore a dedicated lapel mic which I have a min-review for coming up shortly!

So make sure to watch my YouTube video and see how the Baikal Drozd Blackbird does shooting clay pigeons up to 100 feet away...

Buy the Drozd BlackBird Machine Gun in the Canada Store 

Buy Drozd BB Guns in the Canada store

If you have been watching my Full Auto Fun Videos, then you will have noticed that I have recently been using Clay Pigeons as my go-to targets. Generally Clay Pigeons are shot from launchers and used with shotguns since the flight of the Clay Pigeon simulates a bird in flight nicely.

So I thought, why not use them as reactive targets for my Airguns and Airsoft guns? It turns out they work pretty darn good, well at least with 4.5mm Steel BB pistols and I would imagine even better with pellet guns. What about Airsoft guns, will the Airsoft lighter weight plastic BB's have enough mass to get the job done?

You'll have to watch this video to find out the answer to that question when I unload a full magazine of .20 gram Airsoft BB's into some Clay Pigeons using my KWC .50 Desert Eagle...

Buy KWC Airsoft Desert Eagle in Canada

Buy KWC Silver Desert Eagle in Canada 

You guessed it, another Full Auto Fun YouTube Video! And another great Blowback BB gun from the past dusted off and brought out for some more shooting fun :)

You may remember my Cybergun GSG 92 CO2 Blowback 4.5mm Steel BB Pistol that I made several video reviews of, including a how to modify it to shoot both in semi auto and full auto modes. Well the good news is our new KWC Model M92 unlicensed versions (no ugly warning lettering either) now come with the semi and full auto selectable feature so no need to modify, just buy one and your ready to go!

With that said this video is me actually shooting my original Cybergun / KWC Licensed GSG 92 version that I modded to shoot full auto. It was giving me a bit of trouble today but it seemed to work out the kinks near the end.

In an upcoming Full Auto Fun Video I do plan to bring out a new KWC full auto ready M92 and Mini UZI to see how these factory full auto 4.5mm BB guns shoot out of the box.

Buy the KWC M92 BB Pistol

Some more Full Auto Fun Videos coming at you and make sure to check my previous ones out too!

In this Full Auto Fun Field Test Shooting video I bring out my original Umarex Walther PPK Blowback CO2 BB Pistol. The PPK I converted to full auto and that started it all off by being my first YouTube video upload. Wow, that was a while ago now!

I do have to say, modifying the PPK to Full Auto is not recommended, mine originally worked well but the heavy blowback in full auto eventually broke the firing pin setup and I lost it somewhere in my back field. I had to Macgyver a bolt in place to kind of work but now my Full Auto Modded PPK shoots out of control, what I mean by this is when I press the trigger, it does not stop shooting until all the BB's are gone. Safe, I don't think so!

My suggestion is to leave the Umarex Walther PPK as is, it truly is a an awesome CO2 Blowback BB replica with some really decent blowback recoil in a small airgun.

Buy the Umarex Walther PPK in Canada

Buy the Umarex Walther PPK in the US

Full Auto Fun video number three this week and this one is perhaps the craziest one! When you take a Drozd Blackbird that already has a 800-1000 round BB magazine, convert it to 1200 rounds of full auto, add a custom JimC Barrel to it, some bulk CO2 and a bunch of other cosmetic accessories... Well you get the most ridiculous full auto BB gun you can ask for.

Since I had an extra 800-900 BB's more than I am used to when making these full auto videos, I decided to add a few additional targets over and above the clay pigeons I have been using so far. I picked up a nice fairly heavy gauge Santa tin and a rather solid hard wax candle from the dollar store that proved to add some drama to this Full Auto Fun video!

Make sure to also watch my first two Full Auto Fun videos:

• KWC CYBERGUN MINI UZI 4.5MM STEEL BB MODIFIED FULL AUTO FUN

• RAP4 RAP5 MP5 4.5MM STEEL BB MODIFIED FULL AUTO FUN

If you like what you see in this video and want an absolutely crazy BB gun, then checkout our Replica Airguns Store where we Sell the Drozd BB gun and some add ons for it!

Buy the Drozd BB Guns in the Canada Store

This "Full Auto Fun" video focuses on my KWC/Cybergun 4.5mm Steel BB CO2 Blowback Mini UZI BB Gun, where I kick of a short series based around shooting a bunch of 4.5mm Steel BB machine guns! Sounds like fun cause it is fun!

This KWC/Cybergun Blowback Mini UZI comes in a variety of versions, 4.5mm Steel BB and Airsoft versions, it also comes in RWS and KWC Distributed models.

In this video I basically shoot a bunch of clay pigeons positioned in various locations and film it using 4 different camera angles to spice things up a bit.

I also mention some upcoming videos where I will be shooting my RAP4 MP5 and Baikal Drozd Blackbird Full Auto BB guns so make sure to watch those video when I upload them later on this week!

Buy BB Mini UZI in Canada

Buy BB Mini UZI in the US

Buy Airsoft Mini UZI in Canada 

Buy Airsoft Pistols in the US