Materials: Mostly metal with some plastic construction.
Weight: 2 pounds (900 grams).
Barrel: 2.25 inches, non-rifled.
Propulsion: 12 gram CO2.
Action: Revolver, single & double actions.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 6 rounds.
FPS: 360+.
Trigger Pull: The trigger pull on the KWC 357 2.5 Inch CO2 Airsoft Revolver is good in both single and double action, even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, most likely because the spring tension that pushes the inner barrel to make contact with the cylinder is noticeably lighter on the KWC 357's. Even the hammer is smoother and has less wiggle, just a better trigger and hammer mechanism overall.
Accuracy: This is yet to be determined but I did notice on the KWC Airsoft versions of their shell loading Airsoft Revolvers, that they do have a built in preset Hop-up by way of a small rubber bar that goes along the top of the barrel just inside the rear portion. This will create some backspin which will keep the Airsoft BB's trajectory more level but should also help them stay more accurate in general as compared to a plastic Airsoft BB that is not spinning but rather just floating through the air.
Build Quality: The KWC 357 2.5 Inch CO2 Airsoft Revolver being mostly metal has a very good build quality, perhaps even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, even the weight of the KWC 357 is noticeably more! The only real plastic or rubber I could find was in the grips and the shell tips. Fit and finish was also good with no noticeable wear or sloppy workmanship.
Realism: The KWC 357 2.5 Inch CO2 Airsoft Revolver overall is a close copy a the real steel 357 styled revolver. I did notice the rear portion of the receiver (between the rear cylinder and hammer) to be a bit longer perhaps to accommodate the CO2 valve length, but other than that this pistol is super close to the original 357 styled revolver it is based on. Again being all metal gives this CO2 Airsoft revolver very realistic weight and feel and the loadable brass shells make using this gun almost exactly like using a real shell loading revolver but for much less cost per shot and of course a lot less recoil on the hands that a real 357 magnum or even when shooting 38 special shells for that matter ;)
Pretty all the parts work as they would in a similar real steel revolver of this type.
Good overall weight, Very dense because of the shorter barrel.
Should have good overall power, accuracy and shots per CO2 (based on Colt Python testing).
Fully adjustable rear sight for windage and elevation.
Well hidden CO2 Screw.
Recessed barrel.
Not much white writing on the gun.
Nice easy Trigger pull in both single and double action.
Cons:
Short 2.25 inch barrel will rob power but the Dan Wesson style long barrel Airsoft revolvers are know to be a bit hot for some Airsoft games so this may be a good thing.
Grips may be a bit large for people with small hands.
All black sights with no white dots are not great on dark backgrounds or low lighting.
Comments:
The KWC 357 2.5 Inch CO2 Airsoft Revolver is yet another addition to the increasing lineup of shell loading revolvers available today in both Steel BB and Airsoft versions. The 2.5 inch reviewed here is meant to be the compact version with its snub nosed barrel but I would have to say it is not a small gun at all coming in at 2 pounds and with rather large grips and a pretty large cylinder to pack around. But then again, that may be just what you are looking for? The shorter barrel will lower the fps a bit which may bring it back in line with the requirements of some Airsoft fields and the addition of the built in preset Hop-up, this pistol should shoot pretty well out at medium and even longer ranges.
My Vimeo Table Top Review for the KWC 357 2.5 Inch CO2 Airsoft Revolver:
Action: Semi auto blowback, double and single action.
Ammunition Type: Airsoft 6mm plastic BB's.
Ammunition Capacity: 25 rounds
FPS: 390
Trigger Pull: The trigger pull on the KWC Model 226-S5 Sig Sauer CO2 Blowback Airsoft Pistol is what you would expect from a blowback pistol with true single action capability. nice and light with a short take-up in single action and also decent when shooting in double action which for the most part you will not be doing since the blowback pre-cocks the hammer for single action shooting.
Build Quality: Very good, pretty much an all metal construction, good weight and craftsmanship, slide wiggle is minimal, fit and finish is good. As with many of the KWC airguns that use an electromagnetic powder coating, the finish looks great but is thin so it does wear off on the high posts and where metal on metal movement takes place.
Realism: Compared to the real steel Sig Sauer X-Five, the KWC version is pretty close, although it does have a bit different looking slide in terms of the groves or slide serration's, and of course there is no Sig Sauer licensing on the KWC version. You also do not get the ugly white warning instructions so there is a bit of a trade off here and the KWC version also comes with a fully adjustable rear sight which is nice if your aim point is off a bit. Over all the KWC Model 226-S5 Sig Sauer CO2 Blowback Airsoft Pistol is super realistic with its full blowback operation, full size drop out metal magazine and ability to filed strip just like the real steel Sig Sauer it replicates.
All metal construction - Extremely good weight and solid feeling gun. As real as you can get.
Heavy blowback action.
Accurate X-five replica without the Sig Licensing or white warning instructions.
Awesome training gun.
Both SA & DA with excellent trigger pull, very smooth and light.
Has the fully adjustable rear sight for windage and elevation.
Nice high capacity full size drop out metal magazine.
Fully field strippable.
Cons:
Top loading magazine only.
Sacrifice some fps and shots per CO2 because of the heavy blowback but worth it.
Finish is prone to wear on the high spots and metal on metal areas
Comments:
I am really looking forward to my Field Test Shooting video for this Airsoft pistol, the KWC Model 226-S5 Sig Sauer is a nice big heavy pistol with lots of blowback, right up my alley! I am hoping the hop-up will keep this gun in the same accuracy zone as the 4.5mm Cybergun X-Five version, I may just have to test them head to head to find out? If you're a Sig Sauer fan like me, and require a solid useable Airsoft pistol for gaming or just plinking, the KWC Model 226-S5 Sig Sauer CO2 Blowback Airsoft Pistol should do the job well and at a price point that is very reasonable.
My Vimeo Videos for the KWC Model 226-S5 Sig Sauer CO2 Blowback Airsoft Pistol:
Materials: Mostly metal with some plastic construction.
Weight: 2.75 pounds (1218 grams).
Barrel: 5.5 inches, non-rifled.
Propulsion: 12 gram CO2.
Action: Revolver, single & double actions.
Ammunition Type: 4.5mm steel BB's.
Ammunition Capacity: 6 rounds.
FPS: 400fps.
Trigger Pull: The trigger pull on the KWC 357 6 Inch CO2 BB Revolver is good in both single and double action, even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, most likely because the spring tension that pushes the inner barrel to make contact with the cylinder is noticeably lighter on the KWC 357. Even the hammer is smoother and has less wiggle, just a better trigger and hammer mechanism overall.
Accuracy:Based on my results shooting the Umarex Colt Python 357 which is essentially the same gun in a different finish. The results I got shooting my 6 round group from a 30 foot out semi rested position where good overall. Vertically there was about a 2 inch spread while horizontally there was about a 1 inch spread. I did find the plastic tips on the brass shells seemed to be a bit tight at first and this is when I did most of my Chronograph and target shooting. I believe the tightness effected the consistency of the FPS which also effected the accuracy especially up and down. I did get one shot out of the Umarex Colt Python 357 well over the claimed 400 fps but again the fps was rather erratic most likely because of the snug BB fit due to shell break-in.
Build Quality: The KWC 357 6 Inch CO2 BB Revolver being mostly metal has a very good build quality, perhaps even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, even the weight of the KWC 357 came in close to a half of a pound more! The only real plastic I could find was in the grips and the shell tips. Fit and finish was also good with no noticeable chrome wear or sloppy workmanship. It will be interesting to see how the Chrome finish wears over time...
Realism: The KWC 357 6 Inch CO2 BB Revolver overall is a close copy a the real steel 357 styled revolver. I did notice the rear portion of the receiver (between the rear cylinder and hammer) to be a bit longer perhaps to accommodate the CO2 valve length, but other than that this pistol is super close to the original 357 styled revolver it is based on. Again being all metal gives this CO2 BB revolver very realistic weight and feel and the loadable brass shells make using this gun almost exactly like using a real shell loading revolver but for much less cost per shot and of course a lot less recoil on the hands.
It's a revolver with actual shells! Give you the feeling of loading and shooting a real revolver.
Mostly all metal design.
lots of detail, well made, Chrome looks nice, not sure if it will ear better than the black finish?
Good overall weight, heaviest out of all the shell loaders.
Should have good overall power, accuracy and shots per CO2 (based on Colt Python testing).
Fully adjustable sights for windage and elevation.
Well hidden CO2 Screw.
Recessed barrel.
Nice easy Trigger pull in both single and double action.
Cons:
Grips are a bit rough.
Grips may be a bit large for people with small hands.
Black rear sight may not be great on dark backgrounds or low lighting.
Comments:
The ASG Dan Wesson shell loading revolvers reintroduced me to the joy of loading and shooting a revolver which up until that point was not that realistic of an experience when using a BB or Pellet revolver. The KWC 357 6 Inch CO2 BB Revolver like the Umarex Colt Python 357 has taken it up a notch by adding just a bit more overall weight, a smother trigger and hammer mechanism and styling this revolver on the Classic 357 magnum platform. And all of this for even less than the cost of the original Dan Wesson shell loading series CO2 BB revolvers. If you're a revolver fan, make sure to grab one of these, the Chrome finish is really eye catching and would make a great addition to your revolver collection for sure.
My Vimeo Table Top Review for the KWC 357 6 Inch CO2 BB Revolver:
Some more CO2 pistols I will be doing Table Top and Field Test video reviews for in the near future. Some of them I have already reviewed in different caliber versions, either 4.5mm Steel BB or 6mm Plastic Airsoft.
From KWC I show off two revolvers styled after the 357 and if you watched my Umarex Colt Python 357 Review then you will notice the similarities between these KWC made revolvers since they are all made by KWC. The Model 357 6 inch version is finished in Chrome and made to shoot 4.5mm Steel BB's while the KWC Model 357 2.5 inch shoots 6mm Plastic BB's and is in all black. At this time I do not have these KWC revolver listed in the Replica Airguns Canada Store but should have them listed fairly soon...
Better late than never this time, here is my official announcement for the 2014 Halloween Costume Contest Giveaway!
In a nutshell the basic Costume Contest Giveaway rules are as follows:
Upload your Halloween Costume video response before midnight November 10th.
Costumes should be based around a weapon of some sort.
Comment to this YouTube video with a link to your YouTube Halloween Costume entry video.
The winner (Canada & US only) will get a KWC/Cybergun Blowback Pistol of their choice (standard versions).
Of course anyone from outside of Canada and the US can send me a video link to their Halloween Costume videos and I will be sure to include your videos in my Featured Halloween Costume Contest Giveaway 2014 YouTube Playlist even though you are not eligible to win a prize.
Good look to all and looking forward to seeing all of your Halloween Costumes...
This update video is to let all my Canada Online Replica Airguns viewers know about a recent major update and redesign we made to our Canada Replica Airguns Store! In a nut shell, lots of improvements and way easier to find just what you are looking for and watch my reviews while you check out the guns and stuff!
Make sure to watch my Table Top Review for this pistol for if you have not already done so. In this Field Test Shooting portion of my review for the Umarex Magnum Research Baby Desert Eagle CO2 BB Pistol, I shoot 5 rounds through my Chronograph to find out if the claimed 410-420 fps is accurate or not. I also setup a paper target at my standard 30 foot range and shoot 10 rounds using a semi rested position (Standing in the back while resting the gun on a sand bag up front). I did not add any additional sight options to the rails on the Umarex Baby Desert Eagle but rather stuck with the open sights for this field test.
In terms of performance, the Umarex Magnum Research Baby Desert Eagle CO2 BB Pistol did pretty good for a really low cost BB gun with a rather long heavy unpredictable double action trigger. I was a bit surprised when I walked up to review the target to find just over a 2 inch group since while shooting it felt like I was pulling a many of the shots. The open sights are not adjustable in any way but I did shoot down the middle pretty well, but on the high side of the target. I would need to aim low to get this gun to shoot in the bulls-eye form 30 feet away. Either that or add some sort of sight to the top mounted picatinny rail.
My fps Chrony testing for the Umarex Baby Desert Eagle backed the claimed 410-420 fps claims from Umarex, I actually shot a 5 shot average of 417 fps so right on the money here and you may be able to expect even a bit more on a warm summer days since my test was done at moderate fall temperatures.
All in all a decent shooter, good fps, efficient on CO2 and for a heavy DOA trigger I was even able to get a respectable grouping.
Ammunition Capacity: 15 rounds - Internal spring fed magazine.
FPS: 420.
Trigger Pull: The trigger on the Umarex Baby Desert Eagle is double action only, it is a very long trigger that has a medium to heavy pull weight with a very long take up and unpredictable release point. Shooting accurately and controlled will take some time in the saddle so to speak but can be achieved. This pistol is really for plinking at pop cans and such, shooting off hand for fun. My full Field Test Shooting Review to follow shortly...
Build Quality: The Magnum Research Baby Desert Eagle is pretty much all plastic with some internal metal parts. The only actual working external parts are the trigger and the cross bolt safety. The slide catch, hammer, slide mounted safety and take down lever are all moulded into the plastic of the gun and are none functional. Even the magazine is internal so no need for a magazine release here! In the case of the Baby Desert Eagle, perhaps less is more since there is very little to break off or go wrong with this simplistic BB shooter ;)
Realism: This is a very close replica in terms of looks only (not to scale) to the real actual Magnum Research Desert Eagle with licensed trademarks and all. Keep in mind this is the "Baby" version so it is significantly smaller and lighter than the Pellet shooting full size Magnum Research Desert Eagle which could actually be a benefit to those with smaller hands. But again if we are simply talking about "looking like" a Desert Eagle than the Umarex Baby Desert Eagle does look the part, well except for the strange looking slide trigger.
Will fit smaller hands much better than the full sized Desert Eagle.
Has both a top and bottom picatinny rail for all your accessory mounting needs.
Magnum Research Licensed.
Not bad in terms of power, accuracy and CO2 usage combination.
Cons:
Mostly all plastic.
Very few actual working parts, only the trigger and cross bolt safety.
Trigger is very long and kind of unpredictable.
If you decide to mount the included top picatinny rail, you will not be able to use the pistols built in iron sights anymore.
Unsightly screw holes on the left side of this air pistol.
No drop out magazine of any type.
Comments:
OK, so I'm rarely thrilled with the lower budget plastic super simple BB pistols but they do have their place. The tend to work well and stay reliable since there are fewer parts and less mechanical gizmos to get messed up. When the shooting begins and the steel starts to fly, they point the same and they hit your target just the same and all for a lot less out of pocket fun. On the plus side the Umarex Baby Desert Eagle is a pretty decent looking Desert Eagle copy all be it a much smaller version so if you've always wanted the big boy version with it's super huge handle and rather steep price point, well now you can get it in a size and price reduced version that just may be all you really need...
Watch my YouTube Video Review for the Umarex Magnum Research Baby Desert Eagle:
Since I have already doen dedicated reviews for both the T.A.C Converter and XBG BB Pistol, I won't drag this written reviw on too long since yuo can read my other dedicated reviews for each product.
In a nutshell, when you buy the Umarex T.A.C. Converter XBG CO2 BB Pistol Combo, you get the XBG CO2 4.5mm BB Pistol preinstalled in the T.A.C Converter, you also get the included fore-grip which is renovable by the way can coudl be used stand alone on any other gun with an under barrel Picatinny rail.
Keep in mind that this combo kit only works with the XBG Pistol since there are no included adaptors for the other Umarex pistols designed to work with the T.A.C Converter. (H&K USP, S&W M&P40, XBG, CZ Enforcer, Walther P99 DAO, SA177).
The addition of the T.A.C. Converter to the XBG really improves the shoot-ability since the rear folding stock allows for a much more stable hold position. You also have the addition of whit dot sights front and back with the rear sight being adjustable for windage only. I would recommend a compact light weight red dot sight for this gun since using the included open sights are hard to keep in focus because of how close the rear sight ends up being to your eyes when in the shouldered position.
With the top, bottom, and side picatinny rails you can add litterally all types of accessories to this package including a tac light, laser, optical sight, red dot, folding metal sights to name a few.
The XBG BB Pistol has a nice combincation of 400+ fps with tuns of shots per CO2 and respectible accuary with easy access to the Drop out metal BB magazine.
Here is my follow up Shooting Field Test to my ASG STI Duty One Non-blowback Table Top Review. During this Field Test Shooting video review I not only shoot my Non-blowback STI Duty One version but I also compare it to the Blowback ASG STI Duty One to see if fps and accuracy are effected when adding Blowback to the equation? I shoot 5 rounds through my Chronograph with both guns to get an average fps and I also step back 30 feet and setup resting my hands on a sand bag and standing in the back for a fairly secure shooting stance. I did my standard 10 shot grouping for my accuracy test from 30 feet away.
Overall both guns performed similarly and as expected the Blowback did effect the fps but not as much as I expected it to? I was expecting the Non-blowback STI Duty One to be at least 50 fps faster but it was only around 20 or so. I am fairly certain since the fps os so close between the two guns, that you will get more shots form a CO2 out of the Non-blowback ASG STI Duty One since there is no CO2 being used to make the slide recoil back and forth. In the end the Non-blowback STI shot an average fps of 373 while the Blowback version shot an average fps of 356.
When it came to accuracy, both guns performed about the same getting about a 2 inch group from 30 feet back. The Blowback STI did spread the BB's out more from side to side perhaps because of the slide recoil while the Non-blowback ASG STI Duty One seemed to shoot Horizontally tighter.
Personally since both guns shoot almost as high of fps and both STI Duty One's seem to be about the same accuracy wise. Why not just go with the blowback version since you will be shooting in single action most of the time which allows for a faster and lighter trigger pull. The only real downside to the Blowback STI Duty One is perhaps a bit more CO2 usage but you can still expect to get around 100 shots per CO2 which is very good for a CO2 blowback pistol.
Here is my follow up Shooting Field Test to my Umarex CP88 Competition Table Top Review. During this Field Test Shooting video review I not only shoot my CP88 Competition version but I also compare it to the non Competition CP88 version to see if fps and accuracy are effected when adding the longer barrel? I shoot 5 rounds through my Chronograph with both guns to get an average fps and I also step back 30 feet and setup resting my hands on a sand bag and standing in the back for a fairly secure shooting stance. Since the Umarex Walther CP88's have an 8 shot rotary magazine I went with an 8 shot grouping for my accuracy test from 30 feet.
Overall both guns performed similarly and as expected the longer barrel CP88 Competition had the higher fps with 424 average versus 347 average, but what was surprising was how much faster the CP88 Competiton shot. Right around 80 fps more which is significant considering there is only 2 inches more of added barrel length to the Umarex CP88 Competition version. I am thinking that perhaps my CP88 Competition test model was tuned a bit better at the factory?
When it came to accuracy, both guns performed about the same getting about 1 inch group from 30 feet back. This was not a surprise since barrel length has less effect on accuracy than most people think.
Both guns are a pleasure to shoot and will not only perform great shooting close up but if you go with the higher fps Umarex Walther CP88 Competition you will be able to shoot much further out because of the rifled barrel and decent fps performance.
Trigger Pull: The trigger pull on the ASG STI Duty One 1911 Non Blowback is fairly light in both single and double action. Take-up is the same in both modes but when in single action mode most of the trigger pull has little to no resistance until you get to the break point near the end where the hammer is released.
Accuracy: In an Earlier review I shot the Blowback version STI Duty One 1911 air gun at a target from 20 feet away in a free standing position, and it performed well getting a 1.5 to 2 inch grouping right in the center of the target. The rear sight is adjustable for windage which is always nice to have just in case you are shooting a bit to the left or right. For me there was no need to adjust the sights. My Chrony testing with an eight shot averaged result was 373 fps - very decent for a blowback pistol! It will be interesting to see how this Non Blowback version performs since there is more CO2 going to the BB and less gun movement without the Blowback operation.
Build Quality: ASG did a great job designing and making the STI Duty One 1911 Non Blowback BB gun, they didn't really compromise on anything other than going with a polymer frame! With that said all that important parts like the Slide, Slide Catch, Safety, Mag Release, Hammer, Barrel and Magazine are all metal. The fit and finish as with all the ASG air guns is very good!
Realism: The ASG STI Duty One 1911 Non Blowback version is a close replica to the real steel STI 1911, the only real giveaway is the trigger design, as a true 1911 trigger is not your typical lever type. Even with the different type of trigger the STI Duty One is a very good replica complete with STI licensing and trademarks.
No Blowback action but does have a working slide and slide catch.
Adjustable rear sight for windage.
Shoots in both single and double action.
Good quality control, very well made, fit and finish is good.
Should have good power and accuracy like the blowback version, perhaps even a bit better.
May have even better CO2 usage than the already good blowback version.
Metal drop out magazine.
Good STI Replica.
Holds really well in the hand.
Cons:
Trigger is not true to the real steel 1911.
No working grip safety like a real 1911.
Polymer frame rather than a metal frame.
CO2 can be hard to get out.
Comments:
In terms of comparing the Non Blowback version of the ASG STI Duty One 1911 to the Blowback version without actually shooting it, they are pretty much identical except for the double and single action trigger found on the Non Blowback version. Even the slide seems to work the same. The big difference will be when I shoot the Non Blowback ASG STI Duty One. Will it shoot with a lot more FPS and will the reduced slide movement give it more accuracy? I am assuming yes to both of these question but I guess we will all have to wait and see when I do my official Shooting Field Test Comparison...
Watch my Vimeo Video Review for the ASG STI Duty One Non Blowback CO2 BB Pistol:
This video is to give you a heads up on a few guns I will be reviewing shortly. Most of them are different version of guns I have already reviewed except for the Baby Desert Eagle which so far has eluded me :)
So this is not an Airgun related video or even a gun related product review, unless of course, like me you make Gun YouTube videos that require recording gear? In this video I showcase a neat little Lavalier (Lapel) Microphone called the RØDE SmartLav I picked up the other day. Mainly to let you know that the audio in many of my videos will sound a lot better since I will be wearing the RØDE SmartLav during any videos where I get away from the camera.
Camera Microphones usually sound pretty decent when you are up nice and close to them, but as you get further away from the camera (and built in camera mic), you start to sound like you are far away or in a cave. The room tone starts to get mixed in with your voice making the recording sound echoey and thin.
So in order to keep my voice sounding rich and clear, I will be wearing this RØDE SmartLav when I shoot videos that require me to be out front of the camera.
So what makes the RØDE SmartLav so "Smart"? The Smart part is that it works with a "Smart" Phone. All you need to do is plug the RØDE SmartLav into your smartphone, use a recording App like the RØDE Rec and record your voice directly to your Smartphone. Once you are finished your video shoot, you simply match up the audio to the video in your editing software and bingo - you have professional sounding voice audio in your videos.
And because you are recording "hard wired" directly into your iPhone or smart phone, there is no wireless signal to worry about which can often have interference or even cut right out. With the RØDE SmartLav you could literally walk a mile away from the camera and sound exactly as if you where right beside it.
So I think you understand the purpose for one of theses handy little Lapel mics, enjoy the improved audio in my future vids and for those tech savvy people out there, here are the specifications for the RØDE SmartLav:
Acoustic Principle: Pressure Gradient
Active Electronics: JFET
Capsule: 0.10"
Polar Pattern: Omnidirectional - picks up all sides equally
Address Type: End
Frequency Range: 20Hz - 20kHz (selected HPF @ 0)
Output Impedance: 0Ω
Sensitivity: -32.0dB re 1 Volt/Pascal (25.50mV @ 94 dB SPL) +/- 2 dB @ 1kHz
While the weather is still holding on, I setup some clay pigeon targets at varying further out distances than the typically 30 feet I shoot on my deck. I paced out approximately 40-60-80-100+ foot ranges conservatively thinking this would be a good test to see if a 6mm Airsoft rifle could effectively hit targets at any of these ranges using heavy .36 gram Airsoft BB's.
So today I brought out an Airsoft Sniper rifle since this is what it's made to do, the model being the ASG AW .308 Airsoft Sniper. As with many of my shooting videos I captured all the fun using a bunch of different cameras and camera angles along with a dedicated lapel microphone so the audio also comes in nice and clear.
So make sure to watch my YouTube video and see how the ASG AW .308 Airsoft Sniper Rifle does shooting clay pigeons up to 100 Plus feet away...
While the weather is still nice, I decided to setup some clay pigeon targets at varying further out ranges than the typically 30 feet I shoot on my deck. So I figured 40-60-80-100 foot ranges would be a good test to see if a 4.5mm Steel BB rifle could effectively hit targets at any of these ranges.
I did do a similar test earlier on using my Umarex Steel Force but I think the Steel Force may have been a bit underpowered for the 80-100 foot shots.
So today I brought out my Drozd Blackbird since it has a bit of power and what it may lack in accuracy it for sure makes up in volume! As with many of my shooting videos I captured all the fun using a bunch of different cameras and camera angles and today I even wore a dedicated lapel mic which I have a min-review for coming up shortly!
So make sure to watch my YouTube video and see how the Baikal Drozd Blackbird does shooting clay pigeons up to 100 feet away...
I decided to do my Field test of the Gletcher M1891 Sawn Off Mosin Nagant Rifle a little different than my standard filed tests. I pretty much already did a similar Field Test for the M1891 during Table Top Review and if I used the same methods for testing I would most definitely have gotten the same results. Which by the way where a 1.75 inch group from a full 17 round magazine shooting from 30 feet back, and an average of 430 feet per second.
As you know, I have been utilizing clay pigeons in many of my shooting videos so I thought, why not have some more fun and set up a bunch of miscellaneous targets at a variety of distances ranging from 30 feet, right up to 80 feet, and see what I can hit shooting the Gletcher M1891 shooting a couple mags of 4.5mm steel BB's.
Model: Gletcher M1891 (Replica of Sawn Off Mosin Nagant "Obrez").
Materials: Metal & plastic.
Weight: 5.7 pounds (2.6kg).
Barrel: 5.5 inches, smooth bore (inner barrel).
Propulsion: CO2.
Action: Bolt - single shot - single action.
Ammunition Type: 4.5mm Steel BB's.
Ammunition Capacity: 16 rounds. (I was able to fit 17 rounds in the magazine)
FPS: 394fps (120m/s).
Trigger Pull: The trigger pull on the Gletcher M1891 is single action only, the bolt cycle does most of the work setting up the loading of a BB into the chamber and pre-cocking the bolt spring. The take up is minimal and the release is about medium to light weight. The bolt snaps forward firmly and with a nice clanking sound, you can even feel the weight of it as it moves forward.
Accuracy: I did take the opportunity to do a quick pre-test with my Gletcher M1891. I shot several rounds through my Chronograph and averaged around 430 fps which is a bit higher than the claimed 394. I also shot a couple of magazines at a paper target standing 30 feet back using a semi rested position and was about to get a 1.75 inch 17 round group which is pretty good considering I found it kind of unusual to hold the Gletcher M1891 in this manner. The Gletcher M1891 does take some getting used to since you hold it like a rifle but do not rest it against your shoulder for stability.
Build Quality: The Gletcher M1891 is really well made, you can tell by it's robust weight and how solid the action feels when you draw the bolt back and release it the first time. Everything that would be metal on the real Mosin Nagant is metal on the Gletcher M1891 including the full size dropout magazine that holds both the BB's and CO2. Yes the stock is imitation wood but in some ways it is harder than real wood and may actually hold up better. The finish looks great and I like the silver bolt, as with most electromagnetically coated finishes, the coating is not thick so it will wear off in the high spots fairly easily. Some touch up can solve this problem fairly easily.
Realism: I've never actually put my hands on a real steel Mosin Nagant Rifle but from the photos I viewed online, the Gletcher M1891looks really accurate in terms of being a BB replica. Of course the magazine has been adapted to fit CO2 and BB's but once placed in the gun it is nearly impossible to tell it from a real Mosin Nagant, or I should say a sawn off version of one. The weight of this rifle (5.7 pounds) gives it the feeling of genuineness. The only real giveaway is the imitation wood stock which looks pretty good considering. I have read online that a real Mosin Nagant stock can be adapted to fit the Gletcher M1891 so that would indicate that it is fairly true in size and construction to a real Mosin Nagant Rifle.
Pros:
Very Unique BB gun.
A piece of history you can shoot in your back yard.
Mostly all metal gun.
Nice heavy 5.7 pound weight to it.
Adjustable rear sight, at least for elevation.
Nice single action trigger.
Bolt action feels great and has a firm release.
Full size drop out metal magazine that holds both the BB's and the CO2.
More fps than claimed and decent accuracy, I expect to get lots of shots out of a single CO2 because of the magazine design.
Cons:
Stock is plastic but looks good considering.
No real way to adjust windage and the rear sight does wiggle a bit from side to side which could throw off the aim.
Electromagnetically coated finish may be prone to wear in the high spots.
Comments:
The Gletcher M1891 is one of the most interesting BB guns I have had the opportunity to review, it has history, it's kind of a pistol and kind of a rifle at the same time and in this sawn off configuration it looks both old school and modern. I could almost see it being used as the perfect zombi gun ;) Getting away from it's unique looks, the Gletcher M1891 performs very well, shooting a respectable 430 fps with accuracy that surprised me since I found it a bit hard to hold at first. There is something very gratifying about having to work a bot or lever or the hammer on a single action revolver that makes each shot just that much more precious! If you're looking for that ultimate eye catcher that people will have to take a second look at than this is the one for you.
My Vimeo Table Top Video of the Gletcher M1891 Mosin Nagant Replica BB Rifle:
In this video I show you a very interesting 4.5mm CO2 BB replica rifle. A riffle that has a history in the Russian Military going back to the 1800's, but this one has been modified and in a way almost looks modern.
You will have to watch my YouTube update video to see what this mystery gun is, full table top review to follow this week!
I often get asked about using a 4.5mm Steel BB gun for pest control and to be honest I really don't think a BB gun is the right tool even at close range to properly and humanly take care of pests when need be. A much better tool is a high powered pellet rifle in just about any caliber as long as you have taken the time to practice your shot placement at a variety of ranges.
Pellets on the other hand, since they are shot out of a rifled barrel are generally super accurate, even within an inch or so at long ranges. Steel BB's on the other hand will do OK within 20-30 feet but once they get to the farther out ranges, they tend to drift a lot, making it very hard to predict exactly where they are going to go...
So I thought I would back up my words with a real world test by taking an average mid priced BB rifle and taking aim at some clay pigeon targets setup about 100 feet away. Watch my YouTube video to see how my Umarex Steel Force did shooting in semi auto at 100+ feet out.
